Original record summaries, dates and identifiers for this model-year. Records 701–800 of 1,802, ordered newest first. Dated records on this page: Feb 13, 2017–Oct 1, 2017.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Oct 1, 2017Service Bulletin/Repair Instructions
17-NA-172
NHTSA communication ID: 10190234
NHTSA source summary · Original PDF not reviewed by Recallfolio
Rear Suspension Sagging or Sitting Low, Vehicle Not Level After Sitting Overnight Vehicles in new car inventory may be observed or some customers may comment that the rear of the vehicle is riding/sitting low, vehicle sagging, vehicle not level, suspension bottomed out, etc. Review probable causes below.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version. If the Firmware Over-the-Air version on the scan tool equals 6708 the technician will need to contact General Motors Technical Assistance Center for further assistance. If the Firmware Over-the-Air version on the scan tool is lower than 6708 Dealer can order the part thought the Instrument Sales and Service website process.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician the steps to diagnose and repair vehicles that may have an Object Detection System Message Diagnostic Trouble Codes U0075, U026A, U026B, U026C, U0265, U0268, and/or U0269 stored in the active safety module. Technician should inspect his Multiple Diagnostic Interface cable for damage. Technician should use the Multiple Diagnostic Interface on a like vehicle with object detection bus or theEL-47955-1 MDI 1, MDI 2 Self-Test Loopback Adapter,if there are no issues found finish with diagnosing the customer’s concern, if concern is present in the like vehicle replace the Multiple Diagnostic Interface cable.
Source components: BACK OVER PREVENTION: SENSING SYSTEM: CAMERA · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · EQUIPMENT:ELECTRICAL · LANE DEPARTURE · PARKING BRAKE · SERVICE BRAKES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for programming the low speed LAN module due to the mirrors memory position reverse tilt position is inoperative.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin advises the possible issues that may occur using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact Partech and/or the Techline Customer Support Center for additional support.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that Diagnostic Trouble Code B127E in the Human Machine Interface with Regular Production Option Code U42 or UWG will be current when playing a DVD or Blu-Ray on the Integrated Center Stack display. When the disc is ejected the Diagnostic Trouble Code will be history. If the Diagnostic Trouble Code B127E remains current after ejecting the disc follow Service Information diagnostic procedure instructions for B127E with Regular Production Option Code U42 or UWG.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician with information regarding high misfire rates always on #1 cylinder. A customer may complain of misfires or roughness on cold start up with a P0300 diagnostic trouble code. Technician is to add coolant dye to the system and run the engine through warm up to circulate the dye. Pressurize the cooling system after a cold soak and inspect the cylinder with a bore scope for coolant dye. Dye is used to identify coolant over residual fuel being that might be left in the cylinder. The technician is not to replace the cylinder head as it will not correct this concern. In some cases it is necessary to remove the head for inspection. Do not replace the engine for small surface pock marks or a pitting appearance this is normal and do not connect to coolant passages. Usually if porosity is present there will be a break in the carbon ring. Only replace the engine if true porosity is found. Technician is to call Product Quality Center with the latest version of bulletin 02-07-30-029 if porosity is found and engine replacement is required.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin communicates part restriction and ordering process information for OnStar Vehicle Communication Interface Modules (VCIM) (GMNA Only).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a radio screen appears bubbled or is delaminating. Technician should replace the Integrated Center Stack with the latest part number out of the parts catalog.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about customers that may complain of various concerns when using Bluetooth components. Technician should use the Preliminary Information to gather information from the customer on their Bluetooth device and the concern they are having before calling General Motors Technical Assistance Center.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provide policy information on warranty and policy exchange program for electronic products for U.S. and Canada dealers only.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on Information on How to Prevent Inadvertent Vehicle Starting from Key Fob or OnStar Mobile Application and where to locate the information for future use.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides information on Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the transport mode message on and off.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about the text messaging feature on some newer General Motors infotainment systems. Pair the iPhone to the system then enter the Bluetooth settings menu, select the “i” icon next to the vehicle name in the device and enable show notifications. The text messaging feature will be available on the next ignition cycle. However with iPhones text messages cannot be responded to when using the infotainment system, they can only be received. For android devices pair the phone to the system during the pairing process the phone will ask you to allow the vehicle to access the device contacts. A second question will pop up on the device asking to allow the vehicle to access the message access profile. Both have to be allowed for the text messaging feature to work.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:IGNITION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to remove the trunk applique wire harness and body harness connectors to correct a customer concern of unwanted trunk opening, unable to open trunk, back up camera and/or license plate lamps inoperative caused by to corrosion of the applique wiring harness connector X411, as a result of water intrusion.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicatesIn ambient temperatures 100F (37.7 C)degrees or higher, DTCs P2635 and/or P018B may set.The vehicle may also exhibit a hesitation or stalling condition.Excessively Hot and sustained ambient temperatures over 100F (37.7 C) degrees Mainly in TX, AZ, UT, NV, CA, NM (could be any state) causingVapor buildup in fuel feed line.Customers can be advised to utilize fuels with octane levels greater than 91, Refrain from extended idleing periods if possible, park vehicles in covered garage.Replacing the fuel pump will not repare this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides the technician with steps to resolve the issue of an oily substance that may be found on the inside windshield surface, and appears to be leaking from the rear view mirror area. Technician will remove the moisture sensor and clean the glass and mounting bracket with alcohol wipe. If the gel separates from the sensor the sensor will need to be replaced.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides the technician with information on the proper washing of the bright aluminum moldings to avoid the moldings from getting damaged. It is recommended that a non-alkaline solution be used for preparation & washing of the bright aluminum moldings.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about the rear view camera options on the vehicles equipped with rear view camera. The rear view camera brightness can be adjusted on some models while the transmission is in reverse and using the Menu or Select button. To turn off or on the guidelines in the rear view camera, use the radio display Config icon then Display, then the guidelines option.
Source components: BACK OVER PREVENTION: CAMERA SYSTEM · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicatesIn ambient temperatures 100F (37.7 C)degrees or higher, DTCs P2635 and/or P018B may set.The vehicle may also exhibit a hesitation or stalling condition.Excessively Hot and sustained ambient temperatures over 100F (37.7 C) degrees Mainly in TX, AZ, UT, NV, CA, NM (could be any state) causingVapor buildup in fuel feed line.Customers can be advised to utilize fuels with octane levels greater than 91, Refrain from extended idleing periods if possible, park vehicles in covered garage.Replacing the fuel pump will not repare this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary information bulletin provides a procedure on a brief rattle or tick when revving the engine when the vehicle is in P (Park) or N (Neutral). The same rattle or tick can sometimes be heard at the beginning or end of a vehicle acceleration while in D (Drive).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicatesIn ambient temperatures 100F (37.7 C)degrees or higher, DTCs P2635 and/or P018B may set.The vehicle may also exhibit a hesitation or stalling condition.Excessively Hot and sustained ambient temperatures over 100F (37.7 C) degrees Mainly in TX, AZ, UT, NV, CA, NM (could be any state) causingVapor buildup in fuel feed line.Customers can be advised to utilize fuels with octane levels greater than 91, Refrain from extended idleing periods if possible, park vehicles in covered garage.Replacing the fuel pump will not repare this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the programming and activation of the OnStar system. For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a knock noise, seized engine, lower end squeak or squeal from the engine. Technician will inspect the oil control solenoids for metal debris. Also inspect for damage to the cam caps Journals and camshaft journals on the heads. The check the timing chain idler sprockets for stiffness when turning. If any of these instances would be a cause to replace the engine instead of repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a ticking noise on cold start after sitting more than 6 hours. Technician will inspect the oil pump pick-up tube to block seal being compressed. It the seal is compressed replace the seal and retest.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides information regarding the normal characteristic of instrument panel red brake light intermittently comes on.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides information for re-torqueing both (RH and LH) rear shock absorber bolts to eliminate a clunk noise from the rear suspension while driving over bumps.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary information bulletin provides a procedure on a brief rattle or tick when revving the engine when the vehicle is in P (Park) or N (Neutral). The same rattle or tick can sometimes be heard at the beginning or end of a vehicle acceleration while in D (Drive).
Source components: ENGINE · POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin advises of a new fuel injection kit used for decarbonizing the intake valves, and explains how toptier fuels should be used to reduce carbon build up.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides information for re-torqueing both (RH and LH) rear shock absorber bolts to eliminate a clunk noise from the rear suspension while driving over bumps.
NHTSA source summary · Original PDF not reviewed by Recallfolio
this informational bulletin provides Information on Using MyBuick, MyCadillac, MyChevrolet, and MyGMC Phone Applications to Control GM Accessory Remote Start Kits.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides information to dealership personnel which may be helpful when addressing underbody component corrosion with customers.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to Complete the Circuit/System Verification steps to correct a condition of Malfunction Indicator Lamp (MIL) - Check Engine Light On, DTC P182E.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for the GM of Canada OnStar Cellular Communication Upgrade to 3G/4G LTE for vehicles that may need an upgrade.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to apply copper paste to the brake calipers to correct a condition of Brake Squeal or Squeak Noise Intermittently on Initial Brake Applies.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have noise from the exhaust. Technician may find the left hand catalytic converter pipe cracking near cylinder head mounting flange weld. Technician will need to replace the catalytic converter with latest part number from General Motors Service Parts Operations. General Motors is working on a solution for this concern.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on On rare occasions, a security code input message with SPS error code E5659, M5304, and/or M5530 may be displayed in TIS2web when the technician is programming any module. If this concern is encountered, the technician should start by ensuring that the module being programmed is not a used module and that the VIN matches on VIN plate, TIS2web programming screen, and GDS2 module identification information screen.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a "ADAPTIVE CRUISE TEMPORARILY UNAVAILABLE" message on the Driver Information Center when attempting to activate the cruise. Technician will need to perform a Multi Axis Sensor yaw rate sensor learn procedure. If needed, also perform the Long Range Radar Learn called-out in the Radar Sensor Module - Long Range Programming and Setup procedure in Service Information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the engine stops running after extended idle with shifter in park. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle. If the customer exits the vehicle with the fob in their possession while the engine is running and the shifter is left in park, the engine will shut off after 1 - 2.5 hours depending on model year. If the customer is sitting in the vehicle with the engine running and the fob is in the vehicle, the Passive Entry Passive Start system will reach out and look for the fob after 1 - 2.5 hours depending on model year. If the fob is located, the timer will reset an additional 1 - 2.5 hours depending on model year.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to help the dealership technicians perform a parasitic drain test for the OnStar module. When performing battery parasitic drain test, there may be some confusion as to what the normal power consumption reading should be from the OnStar system.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon and may also have an oil or coolant leak. Technician may find coolant or oil in a spark plug tube. If the Spark Plug Tube is leaking and it is determined that the oil or coolant is not coming from a leak above the spark plug then replace the cylinder Head, spark plug and coil.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Bulletin provides guidelines for Dealers required to contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin provides information on how to properly clean wheel speed sensors and wheel bearings that may cause conditions of EBCM Wheel Speed Sensor Diagnostic Aid for ABS Message -Click Or Ratchet Noise- Service Traction Message - Service Stabilitrak Message - Service Steering Message due to dirt and debris.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle that has no XM audio on certain channels but XM channel info is displayed. Technician will need to contact XM and deactivate and activate the module.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have an OnStar Turn-By-Turn Navigation the system that is inoperative. Technician verifies there are no Diagnostic Trouble Codes are present in the Antilock Braking System and Vehicle Communication Interface Module of the vehicle. If no Diagnostic Trouble Codes found call OnStar using the Blue button on the OnStar key pad and ask the advisor for a turn by turn route. Also make a OnStar personal call and a call into the vehicle. If normal diagnostics do not lead to a resolution technician will need to call General Motors Technical Assistance Center for further assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician the steps needed to diagnose and repair the vehicles that may have unwanted or phantom phone calls. Technician will need to determine what type of call the customer is having that is unwanted. The vehicle may receive an incoming call just like any other phone. Typically the customer will hear the phone ringing in the vehicle. This scenario also includes incoming Bluetooth calls. One type of unwanted call can be made if the key pad is faulty the OnStar system will try to make a blue button call for shorted voltage in the circuits. The OnStar module could have an internal fault and produce a ″Phone Unavailable″ audio message also it may have a Diagnostic Trouble Code U1500 or B1000. Refer to diagnostics for the Diagnostic Trouble Code making sure to follow any applicable Bulletins or Preliminary Information sheets. A “Ready” or “OnStar ready” audio message heard while driving. In some cases it has been found that the customer is inadvertently pressing the ″push to talk″ button on the steering wheel controls. On rare occasions, other issues in the steering column or Steering Wheel Control system may induce this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
44180 02 - Customer Satisfaction. Certain vehicles may have key codes which were inappropriately handled by a third party which could increase the risk of vehicle theft. Dealers are to replace all applicable keys and lock cylinders with new key configurations.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to install dust deflectors when replacing wheel bearings on vehicles no matter what the concern is of the vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the programming and activation of the OnStar system. For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information on a rattle, tick, or knock type noise. Any drivability concerns they should be addressed prior to the following diagnostic progression. A sound file or video with sound of the noise needs to be made prior to dis-assembly to help isolate to one area in the engine. There are four different steps to diagnosis the concern. This communication was updated to include the 2017 model year.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on Clicking/Ticking Sound/Noise Heard During Cold Start and that this should be considered a normal characteristic.