The manufacturer’s record · Page 3 of 4
Original record summaries, dates and identifiers for this model-year. Records 201–300 of 334, ordered newest first. Dated records on this page: Dec 1, 2001–May 9, 2014.
Back to 2000 Cadillac ESCALADE problems & recallsThis archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
NHTSA communication ID: 10137901
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides the technician with information on what E85 fuel may due to a non E85 vehicle.
Source components: FUEL SYSTEM, GASOLINE.
Source record 10137901 at NHTSANHTSA communication ID: 10246624
NHTSA source summary · Original PDF not reviewed by Recallfolio
Car and Truck Fix it Right the First Time Issues
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10246624 at NHTSANHTSA communication ID: 10135219
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin explains condensation in exterior lights and replacment guidelines for warranty replacement.
Source components: EXTERIOR LIGHTING.
Source record 10135219 at NHTSANHTSA communication ID: 10111810
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
Source components: EQUIPMENT · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10111810 at NHTSANHTSA communication ID: 10135198
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin is to inform dealers of an improved service strategy to aid in the replacement of hydraulic brake pipes, Customer Care and Aftersales (CCA) has released pre-formed and pre-flared hydraulic brake pipe kits.
Source components: SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:HOSES, LINES/PIPING, AND FITTINGS.
Source record 10135198 at NHTSANHTSA communication ID: 10246646
NHTSA source summary · Original PDF not reviewed by Recallfolio
Pre-Formed and Pre-Flared Hydraulic Brake Pipe Kits Now Available for Service
Source components: SERVICE BRAKES.
Source record 10246646 at NHTSANHTSA communication ID: 10111850
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that when a Canadian customer may comment that when they travel to the United States, they are unable to connect to OnStar or use hands free calling. Dealer can advise the customer that the existing cell phone provider not having roaming agreements in areas outside of Canada. At this time, a customer has the option of contacting OnStar to have a 500 number loaded for OnStar operation while in the United States.
Source components: EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
Source record 10111850 at NHTSANHTSA communication ID: 10245950
NHTSA source summary · Original PDF not reviewed by Recallfolio
Canadian Customers Unable To Place Calls In The United States
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10245950 at NHTSANHTSA communication ID: 10111964
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have the OnStar system does not respond properly to some numbers and/or voice commands. Dealer should direct the customer to review the operational characteristics in the OnStar Users Guide.
Source components: ELECTRICAL SYSTEM:SOFTWARE.
Source record 10111964 at NHTSANHTSA communication ID: 10111927
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · FUEL SYSTEM, GASOLINE · SERVICE BRAKES, HYDRAULIC.
Source record 10111927 at NHTSANHTSA communication ID: 10111894
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10111894 at NHTSANHTSA communication ID: 10190932
NHTSA source summary · Original PDF not reviewed by Recallfolio
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · WHEELS.
Source record 10190932 at NHTSANHTSA communication ID: 10190931
NHTSA source summary · Original PDF not reviewed by Recallfolio
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · WHEELS.
Source record 10190931 at NHTSANHTSA communication ID: 10112013
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
Source components: EQUIPMENT:ELECTRICAL.
Source record 10112013 at NHTSANHTSA communication ID: 10111997
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that a noise or a vibration in the vehicle that seems to be abnormal may not have been there when the vehicle was purchased. Technician should look for Non - General Motors aftermarket accessories installed on the vehicle that can cause these issues.
Source components: EQUIPMENT.
Source record 10111997 at NHTSANHTSA communication ID: 10190934
NHTSA source summary · Original PDF not reviewed by Recallfolio
Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.
Source components: EQUIPMENT ADAPTIVE/MOBILITY · STRUCTURE:FRAME AND MEMBERS:UNDERBODY SHIELDS.
Source record 10190934 at NHTSANHTSA communication ID: 10190933
NHTSA source summary · Original PDF not reviewed by Recallfolio
Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.
Source components: EQUIPMENT ADAPTIVE/MOBILITY · STRUCTURE:FRAME AND MEMBERS:UNDERBODY SHIELDS.
Source record 10190933 at NHTSANHTSA communication ID: 10118885
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on brake line kits now available and how to service them on vehicle.
Source components: SERVICE BRAKES.
Source record 10118885 at NHTSANHTSA communication ID: 10246645
NHTSA source summary · Original PDF not reviewed by Recallfolio
Pre-Formed and Pre-Flared Hydraulic Brake Pipe Kits Now Available for Service
Source components: SERVICE BRAKES.
Source record 10246645 at NHTSANHTSA communication ID: 10112331
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
Source components: ENGINE AND ENGINE COOLING.
Source record 10112331 at NHTSANHTSA communication ID: 10113258
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Supplemental Inflatable Restraint lamp, Service Vehicle Soon lamp on and/or radio locked, possibly after module replacement. Technician will need to check for an incorrect or non-existent VIN number in modules that require them. Technician should ensure that all modules that are replaced are programmed per currently published Service Information. Technician should also check the Sensing and Diagnostic Module part number if it was replaced.
Source components: ELECTRICAL SYSTEM.
Source record 10113258 at NHTSANHTSA communication ID: 10113227
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partech for assistance.
Source components: EQUIPMENT.
Source record 10113227 at NHTSANHTSA communication ID: 10038344
NHTSA source summary · Original PDF not reviewed by Recallfolio
GM: THE FRONT OR REAR DOOR MAY NOT OPEN FROM THE INSIDE OR OUTSIDE HANDLE, THE DOOR WILL NOT UNLOCK WITH ANY METHOD. THE PROBABLY CAUSE AN INCORRECT INSTALLATION OF A HANDLE COMPONENT. *RM UPDATED ON 7/26/2013. ALL 2014 AND PRIOR GM PASSENGER CARS AND TRUCKS. *KB
Source components: LATCHES/LOCKS/LINKAGES:DOORS:LATCH.
Source record 10038344 at NHTSANHTSA communication ID: 10113074
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that after replacing the Instrument Panel Cluster the exchange center is unable to program the actual mileage on the odometer or the actual mileage is unknown. Dealer will need to follow dealer to the General Motors service policies and procedures manual section 3.2.4 odometer servicing.
Source components: ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL · EQUIPMENT.
Source record 10113074 at NHTSANHTSA communication ID: 10130652
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides Warranty Administration - New Labor Codes information.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10130652 at NHTSANHTSA communication ID: 10130627
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a revision of 99-04-20-002G to add 2013-2014 model years.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10130627 at NHTSANHTSA communication ID: 10130626
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a revision of 01-08-49-017A to add new pricing information and payment terms.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10130626 at NHTSANHTSA communication ID: 10112885
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that a noise or a vibration in the vehicle that seems to be abnormal may not have been there when the vehicle was purchased. Technician should look for Non - General Motors aftermarket accessories installed on the vehicle that can cause these issues.
Source components: EQUIPMENT.
Source record 10112885 at NHTSANHTSA communication ID: 10112857
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that, when testing any circuit for open or resistance, it is imperative that all related terminal pin fit and tension be checked when the test steps require disconnection of the connector or component, prior to any component replacement. Always use the recommended terminal test tool during these tests.
Source components: ELECTRICAL SYSTEM.
Source record 10112857 at NHTSANHTSA communication ID: 10133130
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information pre-painting/cleaning process for TPO plastic fascias.
Source components: STRUCTURE:BODY.
Source record 10133130 at NHTSANHTSA communication ID: 10112664
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles may have a no power or no connect concern. Technician will find that the OnStar led is red and Diagnostic Trouble Code U1500 is set. Technician will need to replace the Vehicle Communication Interface Module if the Station Identification number falls in the ranges 14,000,000 - 16,000,000 or 22,000,000 - 23,200,000.
Source components: ELECTRICAL SYSTEM.
Source record 10112664 at NHTSANHTSA communication ID: 10112655
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
Source components: TIRES · WHEELS.
Source record 10112655 at NHTSANHTSA communication ID: 10112641
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that fluid contamination may be directed to one of the following testing centers according to the type of fluid needing testing. Dealer should send the correct fluid to the proper testing center.
Source components: ENGINE AND ENGINE COOLING.
Source record 10112641 at NHTSANHTSA communication ID: 10138217
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a step by step procedure on how to properly use the GM chemicals to eliminate unwanted odors in vehicles and which products to use for each application.
Source components: EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10138217 at NHTSANHTSA communication ID: 10137475
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a step by step procedure on how to properly use the GM chemicals to eliminate unwanted odors in vehicles and which products to use for each application.
Source components: EQUIPMENT.
Source record 10137475 at NHTSANHTSA communication ID: 10126171
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a step by step procedure on how to properly use the GM chemicals to eliminate unwanted odors in vehicles and which products to use for each application.
Source components: EQUIPMENT.
Source record 10126171 at NHTSANHTSA communication ID: 10112607
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
Source components: EQUIPMENT:ELECTRICAL · EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM).
Source record 10112607 at NHTSANHTSA communication ID: 10138213
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a description of the proper wheel installation and proper wheel torque techniques used to install wheels onto vehicles
Source components: EQUIPMENT · WHEELS.
Source record 10138213 at NHTSANHTSA communication ID: 10137471
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a description of the proper wheel installation and proper wheel torque techniques used to install wheels onto vehicles
Source components: WHEELS.
Source record 10137471 at NHTSANHTSA communication ID: 10112600
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician with the axel setup information from American Axle Manufacturing. Technician should be advised that the maximum pinion shim to be used or stacked behind the pinion is 0.050?, and the minimum pinion shim is 0.020? for an 8.6 axle. The range for available pinion depth shims for the 10.5? axle is 0.006? to 0.024?. When setting the backlash it should be set between 0.003? to 0.005? on a new ring and pinion for any American Axle Manufacturing application. The ring and pinion can be reused or adjusted if the mileage is less than 500 miles, if not used for towing. Technician should be advised that a ?roller coaster? or ?hourglass? pattern on the bearings may be normal up to 10,000 miles and possibly longer. With a mis-machined housing you may get a heel pattern on both sides of the gear teeth at build up can generally be corrected with backlash adjustments. When setting up an 8.6? axle with a 5 cut gear set is to use a 0.035? pinion shim and set backlash to 0.004?. When using the newer 2 cut gear set also use a 0.035? pinion shim and still set backlash to 0.004?. To set the gear pattern use backlash to adjust the pattern heel to toe. Use the pinion shim to adjust the height of the pattern. The proper drive pinion bearing pre-load is from 15 - 30 inch pounds with new bearings. The total torque to turn after the differential case is installed should increase 5 - 10 inch pounds at the pinion. A new pinion nut must be used whenever the old one is removed. The axle shaft end play specification is 0.012? per side and the radial specification is 0.002? - 0.003?. Technician should be advised that synthetic lube can be used in all new American Axle Manufacturing axle assemblies. The new pinion seal for the 8.6? axle assembly is a two piece design.
Source components: POWER TRAIN:AXLE ASSEMBLY.
Source record 10112600 at NHTSANHTSA communication ID: 10138211
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides information regarding customer concerns not duplicated and which labor operations to claim when the concern cannot be duplicated. Also provides information on how to submit claims within the global warranty managment.
Source components: EQUIPMENT.
Source record 10138211 at NHTSANHTSA communication ID: 10137469
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides information regarding customer concerns not duplicated and which labor operations to claim when the concern cannot be duplicated. Also provides information on how to submit claims within the global warranty managment.
Source components: EQUIPMENT.
Source record 10137469 at NHTSANHTSA communication ID: 10138201
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information and rules for GM keycode look up applicationa dn the key code security rules and regulations for Canada only.
Source components: EQUIPMENT.
Source record 10138201 at NHTSANHTSA communication ID: 10137459
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information and rules for GM keycode look up applicationa dn the key code security rules and regulations for Canada only.
Source components: EQUIPMENT:ELECTRICAL:ANTI-THEFT DEVICES.
Source record 10137459 at NHTSANHTSA communication ID: 10137458
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for requesting a new key code for customers with lost or stolen keys
Source components: EQUIPMENT:ELECTRICAL:ANTI-THEFT DEVICES.
Source record 10137458 at NHTSANHTSA communication ID: 10138191
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides information on what should be considerd warranty damage or damage that was at fault of the cutomer and how to properly claim them on the warranty paperwork
Source components: EQUIPMENT · VISIBILITY:REARVIEW MIRRORS/DEVICES:EXTERIOR.
Source record 10138191 at NHTSANHTSA communication ID: 10137448
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides information on what should be considerd warranty damage or damage that was at fault of the cutomer and how to properly claim them on the warranty paperwork
Source components: EQUIPMENT.
Source record 10137448 at NHTSANHTSA communication ID: 10138189
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on how to properly mount and balance wheels and tires on heavy duty truck models only
Source components: TIRES · WHEELS.
Source record 10138189 at NHTSANHTSA communication ID: 10137446
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on how to properly mount and balance wheels and tires on heavy duty truck models only
Source components: TIRES · WHEELS.
Source record 10137446 at NHTSANHTSA communication ID: 10112528
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that during battery parasitic drain test, there may be some confusion as to what the normal power consumption reading should be from the OnStar system. Technician should understand the power cycles of the various OnStar systems. All Generation 6, 7, 8, and 9 systems are powered up continuously for 48 hours from ignition off. After 120 hours from ignition off, these systems then completely power off. The Onstar modules draw: * IGN ON - 240 to 400 Milliamp. * IGN OFF - 3 to 20 Milliamp for 48 hours or 120 hours on Gen 9 and vehicle communication platforms. * IGN OFF - 0.2 to 0.8 Milliamp after 48 hours or 120 hours on Gen 9 and vehicle communication platforms.
Source components: ELECTRICAL SYSTEM.
Source record 10112528 at NHTSANHTSA communication ID: 10112523
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have slip in forward ranges immediately after replacing the input housing. Technician will inspect the 3-4 clutches and the forward clutch oil feed passages for leakage between circuits. Technician should apply regulated compressed air to the 3-4 clutch feed hole and the forward clutch feed hole one at a time with the input housing. Technician will need to replace the input housing if there is an air leak 3-4 clutches.
Source components: ELECTRICAL SYSTEM · POWER TRAIN:CLUTCH ASSEMBLY.
Source record 10112523 at NHTSANHTSA communication ID: 10112494
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts. Technician can check Service Information for some accessories. Technician can also contact Partech for assistance.
Source components: EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10112494 at NHTSANHTSA communication ID: 10246951
NHTSA source summary · Original PDF not reviewed by Recallfolio
Programming And Activation Of Replacement OnStar Modules.
Source components: EQUIPMENT:ELECTRICAL.
Source record 10246951 at NHTSANHTSA communication ID: 10038294
NHTSA source summary · Original PDF not reviewed by Recallfolio
GM: THERE ARE SEAT BELT PROBLEMS: DIFFICULTY LATCHING AND UNLATCHING BUCKLE. BUCKLE RELEASE BUTTON IS STICKING. SEAT BELT WARNING LIGHT ILLUMINATED. LIKELY CAUSED BY STICKY BEVERAGES THAT ARE SPILLED INTO THE BUCKLE ASSEMBLY. *RM UPDATED 4/3/12. *PE
Source components: SEAT BELTS · SEAT BELTS:FRONT:WARNING LIGHT/DEVICES.
Source record 10038294 at NHTSANHTSA communication ID: 10042986
NHTSA source summary · Original PDF not reviewed by Recallfolio
GENERAL MOTORS: INFORMATION PROVIDED BY BULLETIN FOR ALL 2012 AND PRIOR GENERAL MOTOR TRUCKS AND PASSENGER VEHICLES REGARDING THE ADJUSTABLE COMFORT AND CUSTOM UPHOLSTERY OF THE DRIVER AND THE PASSENGER HEAD RESTRAINT. *PE
Source components: SEATS:FRONT ASSEMBLY:HEAD RESTRAINT.
Source record 10042986 at NHTSANHTSA communication ID: 10038295
NHTSA source summary · Original PDF not reviewed by Recallfolio
GM: INFORMATION ON FIXING MULTIPLE SITUATIONS RIGHT THE FIRST TIME. *RM
Source components: UNKNOWN OR OTHER.
Source record 10038295 at NHTSANHTSA communication ID: 10036545
NHTSA source summary · Original PDF not reviewed by Recallfolio
BUICK/CADILLAC/CHEVROLET/GMC/OLDSMOBILE AND HUMMER: INFORMATION ON PITMAN ARM SHAFT SEAL SERVICE KIT. DO NOT REPLACE ENTIRE STEERING GEAR FOR PITMAN SEAL LEAK. TECHNICIANS HAVE BEEN REPLACING ENTIRE STEERING GEARS DUE TO NOT BEING ABLE TO SERVICE JUST LEAKING PITMAN SHAFT SEAL. *PE UPDATED 5/9/11. *PE
Source components: STEERING · STEERING:GEAR BOX:SHAFT PITMAN.
Source record 10036545 at NHTSANHTSA communication ID: 10027804
NHTSA source summary · Original PDF not reviewed by Recallfolio
GENERAL MOTORS CORP: SPECIAL COVERAGE ADJUSTMENT; ANALOG ONSTAR DEACTIVATION. *PE UPDATED 2/17/09. *PE
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:SOFTWARE · EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM).
Source record 10027804 at NHTSANHTSA communication ID: 10026804
NHTSA source summary · Original PDF not reviewed by Recallfolio
GMC: FLUID LEAK FROM TRANSMISSION OIL COOLER LINES DUE TO CORROSION. ALL 2000-2006 LIGHT DUTY TRUCKS EQUIPPED WITH THE LIGHT DUTY AUTOMATIC TRANSMISSION. *PE
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:COOLING UNIT AND LINES.
Source record 10026804 at NHTSANHTSA communication ID: 10026586
NHTSA source summary · Original PDF not reviewed by Recallfolio
BUICK CADILLAC CHEVROLET GMC HUMMER OLDSMOBILE PONTIAC SAAB SATURN SERVICE CAMPAIGN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. SPECIAL COVERAGE ADJUSTMENT-ANALOG ONSTAR DEACTIVATION. FCC RULED IN 2002 WIRELESS CARRIERS WOULD NO LONGER RE REQUIRED TO SUPPORT ANALOG WIRELESS NETWORK STARTING IN 2008. *PE CSC LETTER WAS RECEIVED. UPDATED 12/1/08. *PE
Source components: EQUIPMENT:ELECTRICAL.
Source record 10026586 at NHTSANHTSA communication ID: 10024345
NHTSA source summary · Original PDF not reviewed by Recallfolio
EATON LOCKING DIFFERENTIAL CHATTER SHUDDER NOISE ON TURNS, EQUIPPED WITH A LOCKING REAR DIFFERENTIAL RPO G80. *NJ UPDATED 7/17/2008. *PE
Source components: POWER TRAIN:DRIVELINE:DIFFERENTIAL UNIT.
Source record 10024345 at NHTSANHTSA communication ID: 10020874
NHTSA source summary · Original PDF not reviewed by Recallfolio
LEFT FRONT AXLE SHAFT DIFFICULT TO REMOVE. AXLE DIFFERENTIAL LEAK SEAL SHAFT. *KB
Source components: SUSPENSION:FRONT:SPRINGS:LEAF SPRING ASSEMBLY:U-BOLT, LEAF SPRING TO AXLE.
Source record 10020874 at NHTSANHTSA communication ID: 10000062
NHTSA source summary · Original PDF not reviewed by Recallfolio
ANTILOCK BRAKE (ABS) ACTIVATION AT LOW SPEEDS. *TT
Source components: SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP.
Source record 10000062 at NHTSANHTSA communication ID: 10005527
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY WANT TO TOW THEIR VEHICLE BEHIND ANOTHER VEHICLE WITH ALL FOUR TIRES ONT HE GROUND. THIS BULLETIN PROVIDES INFORMATION REGARDING RECREATIONAL (DINGHY) TOWING FOR CERTAIN VEHICLES INCLUDING 1988-2004 CHEVROLET AND GMC LIGHT DUTY TRUCKS. *TT
Source components: UNKNOWN OR OTHER.
Source record 10005527 at NHTSANHTSA communication ID: 10005162
NHTSA source summary · Original PDF not reviewed by Recallfolio
THE SERVICE ENGINE SOON LAMP IS ILLUMINATED, NO 3RD AND 4TH GEAR, THE TRANSMISSION DOES NOT SHIFT CORRECTLY, THE TRANSMISSION FEELS LIKE IT SHIFTS TO NEUTRAL OR A LOSS OF DRIVE OCCURS. *TT
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
Source record 10005162 at NHTSANHTSA communication ID: 619393
NHTSA source summary · Original PDF not reviewed by Recallfolio
MALFUNCTION INDICATOR LAMP (MIL) ON, TRANSMISSION STUCK IN THIRD GEAR, INSTRUMENT CLUSTER INOPERATIVE. *TT UPDATED *EH 2006 AND PRIOR GM PASSENGER CARS AND LIGHT DUTY TRUCKS. *SC
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
Source record 619393 at NHTSANHTSA communication ID: 634999
NHTSA source summary · Original PDF not reviewed by Recallfolio
DIAGNOSIS OF CRACKED OR BROKEN TRANSMISSION CASE. *TT 2006 AND PRIOR CARS AND LIGHT DUTY TRUCKS. *TT
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:LEVER AND LINKAGE:COLUMN SHIFT.
Source record 634999 at NHTSANHTSA communication ID: 10014959
NHTSA source summary · Original PDF not reviewed by Recallfolio
REPLACEMENT OF CONNECTOR WHEN REPLACING FUEL TANK MODULE/FUEL PUMP MODULE. *TT
Source components: ENGINE AND ENGINE COOLING.
Source record 10014959 at NHTSANHTSA communication ID: 10014945
NHTSA source summary · Original PDF not reviewed by Recallfolio
REVISED FRONT CASTER AND CAMBER ADJUSTMENT PROCEDURE. ORIGINAL NOT YET RECEIVED. *TT
Source components: SUSPENSION.
Source record 10014945 at NHTSANHTSA communication ID: 10012703
NHTSA source summary · Original PDF not reviewed by Recallfolio
DIAGNOSTIC INFORMATION FOR INTERMITTENT VEHICLE NO CRANK DEAD BATTERY. *EH
Source components: ENGINE AND ENGINE COOLING.
Source record 10012703 at NHTSANHTSA communication ID: 10011144
NHTSA source summary · Original PDF not reviewed by Recallfolio
POWER WINDOW MOTOR NOW AVAILABLE SEPARATELY FROM THE POWER WINDOW REGULATORY ASSEMBLY. *TT UPDATED *EH
Source components: VISIBILITY:POWER WINDOW DEVICES AND CONTROLS.
Source record 10011144 at NHTSANHTSA communication ID: 10001142
NHTSA source summary · Original PDF not reviewed by Recallfolio
MINOR SCRATCHES TO WOOD STEERING WHEELS. *TT UPDATE. *TT
Source components: STEERING.
Source record 10001142 at NHTSANHTSA communication ID: 10013030
NHTSA source summary · Original PDF not reviewed by Recallfolio
BULLETIN 04-08-64-003, FRONT DOOR POWER WINDOW MOTOR ASSEMBLIES - WARRANTY REPAIR INFORMATION. *TT
Source components: VISIBILITY:POWER WINDOW DEVICES AND CONTROLS.
Source record 10013030 at NHTSANHTSA communication ID: 10010056
NHTSA source summary · Original PDF not reviewed by Recallfolio
EXHAUST VIBRATION RESONANCE OR MOAN. (2004-2005 GMC DENALI) *SC
Source components: ENGINE AND ENGINE COOLING.
Source record 10010056 at NHTSANHTSA communication ID: 10009936
NHTSA source summary · Original PDF not reviewed by Recallfolio
EXHAUST VIBRATION RESONANCE OR MOAN 99-05 FULL SIZE TRUCKS AND UTILITY VEHICLES WITH GEN 3 V-8 ENGINES. *TC
Source components: ENGINE AND ENGINE COOLING:COOLING SYSTEM.
Source record 10009936 at NHTSANHTSA communication ID: 10009665
NHTSA source summary · Original PDF not reviewed by Recallfolio
REPLACEMENT FLEXPLATE MAY HAVE LARGER BOLT HOLES THAN THE ORIGINAL FLEXPLATE. *TT
Source components: POWER TRAIN.
Source record 10009665 at NHTSANHTSA communication ID: 10009593
NHTSA source summary · Original PDF not reviewed by Recallfolio
DOWNHILL CRUISE CONTROL SURGE. *TT
Source components: VEHICLE SPEED CONTROL:CRUISE CONTROL.
Source record 10009593 at NHTSANHTSA communication ID: 10008901
NHTSA source summary · Original PDF not reviewed by Recallfolio
REAR AXLE LOCKING DIFFERENTIAL CHATTER SHUDDER NOISE ON TURNS. *MJ
Source components: SUSPENSION:REAR.
Source record 10008901 at NHTSANHTSA communication ID: 10008883
NHTSA source summary · Original PDF not reviewed by Recallfolio
93-00 FULL SIZE UTILITIES (GMT 400 OLD STYLE ONLY) AC BLOWS WARM AND THE HIGH SIDE PRESSURE IS TOO HIGH. *MJ
Source components: EQUIPMENT:APPLIANCE:AIR CONDITIONER.
Source record 10008883 at NHTSANHTSA communication ID: 10008762
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE ENGINE SOON (SES) LIGHT ON WITH P0446 DUE TO DUST IN THE EVAP VENT VALVE ON VEHICLES THAT ARE OPERATED IN DUSTY ENVIRONMENTS, SUCH AS FARMING OR OFF-ROAD APPLICATIONS. *TT
Source components: ENGINE AND ENGINE COOLING:ENGINE.
Source record 10008762 at NHTSANHTSA communication ID: 10007237
NHTSA source summary · Original PDF not reviewed by Recallfolio
4L60E, 4L65E FORWARD AND LOW REVERSE WAVED STEEL CLUTCH PLATE APPEARANCE CHANGE. *TT
Source components: POWER TRAIN.
Source record 10007237 at NHTSANHTSA communication ID: 10006946
NHTSA source summary · Original PDF not reviewed by Recallfolio
DIAGNOSTIC TROUBLE CODE B1000. *MR
Source components: ELECTRICAL SYSTEM.
Source record 10006946 at NHTSANHTSA communication ID: 10005474
NHTSA source summary · Original PDF not reviewed by Recallfolio
NO 2ND, NO 4TH AND NO REVERSE. TO INCLUDE 2004 LIGHT DUTY AUTOMOBILES AND TRUCKS EQUIPPED WITH 4L60E OR 4L65E AUTOMATIC TRANSMISSION. *TT
Source components: POWER TRAIN.
Source record 10005474 at NHTSANHTSA communication ID: 10004214
NHTSA source summary · Original PDF not reviewed by Recallfolio
POOR PERFORMANCE FROM A STOP IN 2WD, AUTO OR 4WD HI. 2003, 2003 CADILLAC EXT ALSO INCLUDED. *TT
Source components: POWER TRAIN.
Source record 10004214 at NHTSANHTSA communication ID: 10004212
NHTSA source summary · Original PDF not reviewed by Recallfolio
THE NVG 136 ALL WHEEL DRIVE (AWD) TRANSFER CASE AND THE 236 AND 246 NVG SELECTABLE TRANSFER CASE SHUDDER ON TURNS. *TT
Source components: POWER TRAIN:TRANSFER CASE (4-WHEEL DRIVE).
Source record 10004212 at NHTSANHTSA communication ID: 10004278
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY WANT TO TOW THEIR VEHICLE BEHIND ANOTHER VEHICLE WITH ALL FOUR TIRES ONT HE GROUND. THIS BULLETIN PROVIDES INFORMATION REGARDING RECREATIONAL (DINGHY) TOWING FOR CERTAIN VEHICLES INCLUDING 1988-2004 CHEVROLET AND GMC LIGHT DUTY TRUCKS. *TT
Source components: UNKNOWN OR OTHER.
Source record 10004278 at NHTSANHTSA communication ID: 10002886
NHTSA source summary · Original PDF not reviewed by Recallfolio
SHIFT STABILIZATION AND TOW/HAUL MODE FEATURE FOR HYDRA-MATIC 4L60-E/4L65-E AND 4L80-E/4L85-E TRANSMISSIONS. *TT
Source components: POWER TRAIN.
Source record 10002886 at NHTSANHTSA communication ID: 10001298
NHTSA source summary · Original PDF not reviewed by Recallfolio
ROUGH IDLE AFTER START, AND/OR A SERVICE ENGINE SOON (SES) LIGHT. VARIOUS MODELS INCLUDING THE 1995 CHEVROLET AND GMC S/T MODELS. *TT
Source components: ENGINE AND ENGINE COOLING:ENGINE.
Source record 10001298 at NHTSANHTSA communication ID: 10001110
NHTSA source summary · Original PDF not reviewed by Recallfolio
SLIPS IN 4-WHEEL DRIVE, NOISE, VIBRATION, LEAKS, HOT ODOR. *TT
Source components: POWER TRAIN.
Source record 10001110 at NHTSANHTSA communication ID: 10000749
NHTSA source summary · Original PDF not reviewed by Recallfolio
ANTILOCK BRAKE (ABS) ACTIVATION AT LOW SPEEDS ON VARIOUS MODELS INCLUDING THE 1995 AND 1996 ENVOY. *TT
Source components: SERVICE BRAKES, AIR:ANTILOCK.
Source record 10000749 at NHTSANHTSA communication ID: 10007838
NHTSA source summary · Original PDF not reviewed by Recallfolio
DIAGNOSTIC INFORMATION FOR INTERMITTENT TRANSMISSION DOWNSHIFT, SLIP, BUSY/CYCLING TCC OR NOISY COOLING FAN. *TT
Source components: POWER TRAIN.
Source record 10007838 at NHTSANHTSA communication ID: 10008622
NHTSA source summary · Original PDF not reviewed by Recallfolio
SELF-ARTICULATING HEADREST MECHANISM ON THE SECOND ROW SEATS WITH CLEARANCE LESS THAN ALLOWED FOR INADVERTENT INSERTION OF OBJECTS OR EXTREMITIES SMALLER THAN THE INITIAL OPENING. *TT
Source components: SEATS:FRONT ASSEMBLY:HEAD RESTRAINT.
Source record 10008622 at NHTSANHTSA communication ID: 634905
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES WILL NOT MOVE WHEN 4-WHEEL DRIVE IS REQUESTED, NOISE, SHUDDER, POOR PERFORMANCE, TRANSMISSION / TRANSFER CASE SLIPS, TRANSMISSION WILL NOT UPSHIFT, SLIPS IN 4-WHEEL DRIVE. *TT
Source components: POWER TRAIN.
Source record 634905 at NHTSANHTSA communication ID: 634839
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUBJECT REGARDING REVISED WHEEL SPEED SENSOR REPLACEMENT PROCEDURE. *TT
Source components: SERVICE BRAKES, AIR:ANTILOCK:WHEEL SPEED SENSOR.
Source record 634839 at NHTSANHTSA communication ID: 634909
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUBJECT REGARDING TIE ROD REPLACEMENT- INNER PROCEDURE. *TT
Source components: STEERING:LINKAGES:TIE ROD ASSEMBLY.
Source record 634909 at NHTSANHTSA communication ID: 634903
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUBJECT REGARDING REVISED DIAGNOSTIC TROUBLE CODE B2725. *TT
Source components: UNKNOWN OR OTHER.
Source record 634903 at NHTSANHTSA communication ID: 634815
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMMENT ON A HARSH 1-2 UPSHIFT AND THE CHECK ENGINE LIGHT OR SERVICE ENGINE SOON INDICATOR IS ILLUMINATED AND DIAGNOSTIC TROUBLE CODE P1870 SET. *TT
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
Source record 634815 at NHTSANHTSA communication ID: 632346
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUBJECT REGARDING REVISED DRUM BRAKES COMPONENT SPECIFICATIONS FOR PICKUP AND UTILITY MODELS. *TT
Source components: SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DRUM.
Source record 632346 at NHTSANHTSA communication ID: 632332
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUBJECT REGARDING REVISED DRUM BRAKES COMPONENT SPECIFICATIONS. *TT
Source components: SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DRUM.
Source record 632332 at NHTSANHTSA communication ID: 628905
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMMENT ON ROUGH IDLE AFTER START UP, ESPECIALLY AFTER SETTING OVERNIGHT. *TT
Source components: ENGINE AND ENGINE COOLING:ENGINE:GASOLINE.
Source record 628905 at NHTSA