Original record summaries, dates and identifiers for this model-year. Records 1,001–1,100 of 1,589, ordered newest first. Dated records on this page: Mar 12, 2014–Jul 31, 2014.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Jul 31, 2014Service Bulletin/Repair Instructions
PIC5959B
NHTSA communication ID: 10112144
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle that has no XM audio on certain channels but XM channel info is displayed. Technician will need to contact XM and deactivate and activate the module.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a message on the radio "maximum number of phones are currently paired to the vehicle". Dealer should advise the customer this is normal operation of the vehicle due to the maximum number of five phones can be paired to a vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides technicians with ways to decrease the tire slipping on the rim and reduce to possible chances of the customers concerns over tire vibration are repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides technicians with ways to decrease the tire slipping on the rim and reduce to possible chances of the customers concerns over tire vibration are repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides technicians with ways to decrease the tire slipping on the rim and reduce to possible chances of the customers concerns over tire vibration are repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a brake pedal may not raise or seem stuck down after a normal braking event. Technician will need to replace the brake pedal arm.
Source components: SERVICE BRAKES, HYDRAULIC:PEDALS AND LINKAGES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about a service engine soon light on. Technician will find diagnostic trouble codes P0089 and P228D set in the engine control module. This concern could be due to an incorrect intake camshaft or camshaft actuator sprocket. A diagnostic trouble code of P0171 could also set from installing incorrect injectors.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Technical bulletin provides a procedure to request a hard mute from Onstar when navigation is annoucing directions and to correct the customers concern of the radio being loud during navigation.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin was created to inform the technician of cold start ticking noises in the engine compartment may be caused by the fuel pump and/or the fuel injectors and no
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Technical bulletin provides a procedure to request a hard mute from Onstar when navigation is annoucing directions and to correct the customers concern of the radio being loud during navigation.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin was created to inform the technician of cold start ticking noises in the engine compartment may be caused by the fuel pump and/or the fuel injectors and no
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Technical bulletin provides a procedure to request a hard mute from Onstar when navigation is annoucing directions and to correct the customers concern of the radio being loud during navigation.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin was created to inform the technician of cold start ticking noises in the engine compartment may be caused by the fuel pump and/or the fuel injectors and no
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about a service engine soon light on. Technician will find diagnostic trouble codes P0089 and P228D set in the engine control module. This concern could be due to an incorrect intake camshaft or camshaft actuator sprocket. A diagnostic trouble code of P0171 could also set from installing incorrect injectors.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This information for Warranty administration - Changes the Service Policy and Procedures Section 1.6.2.11 and list the requirements for the dealer to comply.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This information for Warranty administration - Changes the Service Policy and Procedures Section 1.6.2.11 and list the requirements for the dealer to comply.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a short, sharp rattle noise from the front of the engine at start up. Technician may find Diagnostic Trouble Codes P0011 P0014 P0016 or P0017. Technician will need to inspect the engine belt. If the vehicle is equipped with a hydraulic power steering, technician will need to verify the power steering pulley outer edge is aligned flush with shaft and repair as needed. If pulley alignment is correct or vehicle does not have hydraulic steering, replace the engine belt. If the noise is still present and it is coming from the cam actuators they will need to be replaced.
Source components: ENGINE AND ENGINE COOLING · ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:BELTS AND ASSOCIATED PULLEYS · STEERING:HYDRAULIC POWER ASSIST SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CHEVROLET/BUICK/GMC: AFTER HAVING INTAKE CAMSHAFT OR INTAKE CAMSHAFT ACTUATOR REPLACED, SERVICE ENGINE SOON LIGHT IS ON, ENGINE HAS LOW POWER OR IS IDLING ROUGH WITH A WHINE NOISE FROM HIGH PRESSURE FUEL PUMP. MODEL 2010-2011 LACROSSE, EQUINOX, TERRAIN, REGAL. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have Diagnostic Trouble Code P00C6 and/or P228C set. Technician will need to inspect the terminals at the Engine Control Module for fit and tension as well as the crimp to wire connection. Terminals to inspect in the ECM are connector x2 terminals 3, 18, and 19 for the fuel rail pressure sensor. Also connector x3 terminals 16 and 32 for the high pressure fuel pump.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin was created to aid the technician in diagnosing the difference between a shock or strut that has a fluid residule from a possible external source from a leaking shaft seal.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a short, sharp rattle noise from the front of the engine at start up. Technician may find Diagnostic Trouble Codes P0011 P0014 P0016 or P0017. Technician will need to inspect the engine belt. If the vehicle is equipped with a hydraulic power steering, technician will need to verify the power steering pulley outer edge is aligned flush with shaft and repair as needed. If pulley alignment is correct or vehicle does not have hydraulic steering, replace the engine belt. If the noise is still present and it is coming from the cam actuators they will need to be replaced.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary bulletin provides a procedure on how to reset the power folding mirriors after they been folded manually, to fix the customers concern of the mirriors shaking or fluttering at normal driving speeds.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary bulletin provides procedures on how to reset or refresh the XM radio receiver is the customers states that they only get a few channels.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may not receiving all channels on the XM band. Technician will need to use a scan tool and verify current Digital Radio Receiver Status under Data Display. Technician will need to look at the second line labeled Digital Radio Receiver Status will display a number of 00 - 04. Technician will repair per the status code.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the programming and activation of the OnStar system. For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle that have a Malfunction Indicator Lamp on. Technician may find Diagnostic Trouble Codes P0601, P0603, P0604, P062F or P1621 stored in the Transmission Control Module. Technician will need to ensure that the Diagnostic Trouble Codes are set in the Transmission Control Module. If the Diagnostic Trouble Codes are only set in the Transmission Control Module reprogram the Transmission Control Module.
Source components: POWER TRAIN · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides explanation on using the tire sealent in the GM kit as a temporary fix only untill the tire can be properly repaired under the new tire warranty.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a process to the service agents that are not required to contact PQC, to determine when to replace a assembly as opposed to repairing and if an engine or transmission is being returned, that it has all the information in relation to that part being returned.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to test for oil consumption and install new pistons and rings if no signs of consumption or oil leaks have been validated.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have the Antilock Braking System, Service Traction Control System, and/or Service Stabilitrak lights are on. The Electronic Brake Control Module may have one or more of the following Diagnostic Trouble Codes C0035-C0050 with specifically symptom 18, 5A, or 0F. Technician will gain access to the correct wheel bear per the Diagnostic Trouble Code that is set. If debris is found on the magnetic encoder ring it will needed to be cleaned.
Source components: SERVICE BRAKES, AIR:ANTILOCK · SERVICE BRAKES, AIR:ANTILOCK:CONTROL UNIT/MODULE · SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP · SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP:CONTROL UNIT/MODULE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
GM: THE BRAKE, TRACTION, OR STABILITY LIGHTS ARE ON BECAUSE OF DEBRIS STUCK ON THE WHEEL SPEED SENSOR. UPDATED ON 06/15/2011. *KB UPDATED ON 06/20/2011. *RM UPDATED 6/27/11. *PE UPDATED 10/3/11. *PE UPDATED 05/08/2013 *JS UPDATED ON 7/9/2013. *KB UPDATED 7/28/14. *PE
Source components: SERVICE BRAKES, AIR:ANTILOCK:WHEEL SPEED SENSOR · SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP:WHEEL SPEED SENSOR/TONE RING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have black smoke on a cold start. A dual-pulse injection strategy is utilized during engine cold start to reduce the time required to bring the catalytic converter up to operating temperature. This split injection strategy lasts for about 60 seconds on cold start. This process may cause the customer to see increased black smoke during cold start and should be considered normal.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a ticking noise on cold start after sitting more than 6 hours. Technician will inspect the oil pump pick-up tube to block seal being compressed. It the seal is compressed replace the seal and retest.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This information bulletin provides the technician with additional information on fixing the vehicle right the first time by listing possible concerns to specific vehicles.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a radio with the timeshift feature is inoperative. Dealer will need to replace the radio for this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
GM: SOME DTC CODES MAY BE SET, P0016, P0017, P0018, P0019, P0008, OR P0009. 3.6 LY7 WITH CAM ACTUATOR DTC.THE RELUCTOR FOR THE CRANKSHAFT SENSOR PRESSED ON THE CRANKSHAFT MAY HAVE MOVED. ALSO INCLUDED BUICK ALLURE MODEL YEAR 2005. *JS
NHTSA source summary · Original PDF not reviewed by Recallfolio
GM: INCONSISTENT REAR BACK UP CAMERA OPERATION, BLUETOOTH DELAY, INTERMITTENT AUDIO CONCERNS, BLANK DVD DISPLAY, AS WELL AS OTHER NAVIGATION RADIO/CLOCK CONCERNS. THE RADIO MAY NEED TO BE REPLACED. *JS
NHTSA source summary · Original PDF not reviewed by Recallfolio
GM: SOME VEHICLES REQUIRE REPLACEMENTS FOR HIGH FEATURE V6 TIMING CHAIN KITS AND GUIDE REPLACEMENTS. ALSO INCLUDED CHEVROLET CAPTIVA. MODEL YEARS 2007-2013. *JS UPDATED 7/18/14. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that Diagnostic Trouble Codes P0016, P0017, P0018, P0019, P0008 or P0009 may be set. Technician will need to inspect for loose timing chains or tensioners. If after following Service Information diagnostics the root cause is not found inspect the reluctor for the crankshaft sensor. If the reluctor has moved then replace crankshaft.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to test for oil consumption and install new pistons and rings if no signs of consumption or oil leaks have been validated.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that were built with a dampener on the rear toe adjust link. Technician can remove the dampener, engineering has determined that this dampener does not make a noticeable impact on noise, vibration, or harshness.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary bulletin provides a procedure to repair or replace the steering column seal to correct the customers concern of a groan, squeak or rubbing noise when turning the steering wheel.