2017 BMW X5 Manufacturer communications & TSBs.Page 3
Original record summaries, dates and identifiers for this model-year. Records 201–299 of 299, ordered newest first. Dated records on this page: Jan 1, 2016–May 1, 2017.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
May 1, 2017Service Bulletin/Repair Instructions
B120817
NHTSA communication ID: 10149227
NHTSA source summary · Original PDF not reviewed by Recallfolio
POWERTRAIN FAULTS DUE TO CHAFING OF ENGINE WIRING HARNESS. One or more of the following fault codes are stored in the DDE: 29FB00 - DeNOx system, warning and switching off scenario: Warning level 1 280D00 - NOx-Sensor upstream DeNOx-catalytic converter, signal NOx: NOx-Signal invalid for too long 280F00 - NOx-Sensor downstream DeNOx-catalytic converter, signal NOx: NOx-signal invalid for too long 29FC00 - DeNOx-system, warning and switch-off scenario: Warning level 2 CD840A - FA-CAN bus: Control unit switched off from bus (Bus off) CD94C7 - Message (RQ_PWR_EL_EPS, 234.0.2, FX): Messaging from EPS failed CD951C - Message (AVL_STMOM_DV_ACT_AVL_FORC_GRD, 49.0.2, FX):Messaging from EPS failed CD9536 - Message (DIAG_OBD_SCR, 0x3EE, FA): Messaging from SCR control unit failed CD953A - Message (ST_FFLV_SCRA, 0x40B, FA): Messaging from SCR control unit failed CD953C - Message (ST_RESO_SCRA, 0x8A, FA): Messaging from SCR control unit failed CD942B - Message (DT_GRDT, 0x1AF, A): Messaging from transmission control unit failed CD946B - Message (ST_GRB_ECU, 0x39A, FA): Messaging from transmission control unit failed CD9487 - Message (RQ_TORQ_CRSH_GRB, 0xB0, A): Messaging from transmission control unit failed CD94B9 - Message (DISP_RPM_ENG_DYNS, 0xF8, A): Signal(s) in message invalid CD94BA - Message (DISP_RPM_ENG_DYNS, 0xF8, A): Messaging from transmission control unit failed CD94C3 - Message (DIAG_OBD_GRB, 0x396, FA): Messaging from transmission control unit failed CD94DC - Transmission control unit, communication: Transmission communication via A- CAN and FACAN failed CD94ED - Message (DT_DISP_GRDT, 0x3FD, FA): Messaging from transmission control unit failed CD950D - Message (RQ_TORQ_CRSH_GRB_2, 0xA0, A): Signal(s) in message invalid ? CD950F - Message (RQ_TORQ_CRSH_GRB_2, 0xA0, A): Messaging from transmission control unit failed ? CD9549 - Message (DIENSTE-ID2=19 request MSA function, 0x598, FA): Message from transmitter control unit (EGS_EL) failed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"?Telematics Device Spares Replacement Part Activation via DCSnet for BMW Assist What's New: ? Model: All models added along with 6AC option code ? Situation: All information added ? Information: Deleted CDMA related information and added activation of Wi-Fi control unit ? Procedure: Added "Note" regarding ConnectedDrive support hotline information . A replacement telematics control unit must only be activated for vehicles with an active BMW Assist subscription. Note: 2G CDMA and 2G GSM telematics control units cannot be activated because they are no longer supported and the supporting network(s) have been decommissioned. INFORMATION The following changes have taken place: All Telematics control unit replacements must be activated by Part managers via the DCSnet application. New steps included in the procedure for activating Telematics control unit replacements for vehicles equipped with Wi-Fi Hotspot (6WD)."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"LIST OF AVAILABLE FM RADIO STATIONS TEMPORARILY NOT AVAILABLE. INFORMATION As of 11/2015, all Entry-NAV/Media head units supplied in new vehicles were upgraded for improved noise characteristics and quality. As a part of this upgrade, the hardware updating the sender lists was changed from an "update after every diversity reception interruption or maximum of four minutes" configuration to "regular interval updates (every four minutes) without regard to diversity reception status" configuration. This may cause a delay of up to four minutes for updates to the sender list when leaving areas of poor reception. The last received transmitter, before the entrance into underground car parking or a tunnel, is still received and will show station identification. This fixed interval update does not apply to Traffic Message Channel updates which remain active. This new equipment operation pattern may be noticed by the customer after replacement of their Head unit. All replacement Head units delivered since 01/2016 have the upgraded design. An immediate solution would be for the customer to select one of their stored favorite stations via the menu or favorites buttons. PARTS INFORMATION Parts exchange or a software update are not effective or approved for this situation. WARRANTY INFORMATION Not applicable."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"?BMW Maintenance Program: 12-Volt Battery Replacement Measure What's new: ? "Models" updated: Model Year 2017 vehicles added ? "Models" updated: Model Year G12 (7 Series) excluded from program ? "Procedure" updated: N63R engine added to 2016 Model Year G12 (7 Series) ? Attachment updated with G12 (7 Series) production date range for 2016 Model Year. INFORMATION This bulletin outlines a customer satisfaction measure that has been designed exclusively for the BMW vehicles listed above. It involves the replacement of the 12-volt battery as a preventive maintenance measure. This 12-volt battery replacement measure is: Effective for repairs dated on or after January 1, 2015. Applicable to vehicles that are still covered by the BMW Maintenance Program. This program is valid for 4 years or 50,000 miles, whichever occurs first. The calculation is based on the current date of repair. It is "applicable" when the 12volt battery was not replaced within the last 12 months. You can then perform the battery replacement as outlined below. Please check the warranty claim history for the specific vehicle in the DCSnet Warranty Vehicle Inquiry to confirm the battery was not already replaced within the previous 12 months."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"SME FAULT CODE 21F02A. Upon starting the vehicle, the following CC message is displayed to the customer: "Powertrain malfunction!" (CCM-ID: 633) In addition, one or several of the following CC message(s) may be displayed: "Charging not possible" (CCM-ID: 804), "Hybrid system malfunctioning!" (CCM-ID: 585), "Drive. No restart" (CCM-ID: 586) or "Engine fault! Power loss" (CCM-ID: 29). Possible hardware defect of the safety box."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"HV CHARGING INTERMITTENTLY NOT POSSIBLE. HV charging is intermittently not possible. When charging problem occurs, a CCM 804 "Charging Not Possible" will be displayed. Affected vehicles may begin to charge if the charger plug is rapidly plugged/unplugged several times. Charging problem may be noticed consistently at same charging location, but not at others. KLE Software."
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE ACTION: CHECK CHARGING OF THE HIGH VOLTAGE BATTERY. High-voltage charging system may not work correctly. Alternative Mobility Solutions (AMS) Reimbursement This BMW Service Action repair qualifies for Alternative Mobility Solution (AMS) expense reimbursement. Please refer to SI B01 29 16 for claim submission details. Intermittent hardware failure of the charging module (KLE).
NHTSA source summary · Original PDF not reviewed by Recallfolio
SLIGHT SHUDDERING UNDER ACCELERATION FROM 40-60MPH. When initiating gradual acceleration at between 40mph to 60mph, customer may experience some minor shuddering under acceleration. Some situations that may lead to this experience would be: Gradual depressing of the accelerator pedal Change in load (increase in road grade) Acceleration request by cruise control The following conditions must be present for this situation to occur: "Auto eDrive" driving mode selected Engine speed of approximately 1500 rpm Transmission in Drive, running in 7th or 8th gear, Low State of Charge (SOC) of high voltage battery. No fault codes are stored as a result of this performance issue. Stacking of tolerances in the driveline.
NHTSA source summary · Original PDF not reviewed by Recallfolio
LOSS OF SEAT ADJUSTMENT CONTROL. What is new? Procedure section updated with video link as a repair hint. Front seat electric adjustment controls do not function. Electrostatic discharge damage the seat module.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Ticking Noise from the Front Axle When Cornering What's New: ? Changes to the procedure, parts information and warranty labor operations. The customer may complain of a ticking noise from the front axle when cornering, maneuvering, parking or pulling away from a parking space. The noise can be heard as a metallic ticking from the area of the front wheels. Movement between the inner contact surfaces of the brake disc and drive flange of the wheel bearing hub.
NHTSA source summary · Original PDF not reviewed by Recallfolio
?N20, N26, N55, N63TU, S63TU and S55 Engines: Bosch Injector ETK Part Number Error What's New: ? Identifying the injector type using the ISTA test plan ? Determining the injector part number using the new the parts table. The current version of the ETK incorporates multiple part number errors for the Bosch type injectors. Ordering the injectors by VIN number or manual identification in ETK may result in an incorrect part number.
NHTSA source summary · Original PDF not reviewed by Recallfolio
?SATELLITE RADIO DETERIORATION IN RECEPTION QUALITY DUE TO NEW CELLULAR FREQUENCIES . INFORMATION Inform the customer that the introduction of these expanded frequencies by the wireless mobile providers may be influencing reception quality. BMW is currently working with the wireless mobile providers in order to improve the quality of reception and help alleviate the issues that are caused by the wireless mobile expanded frequencies. Once we have more information about this situation this service information bulletin will be updated. Currently Satellite Radio is provided by SiriusXM for BMW customers via geosynchronous (GEO) satellites located roughly above the equator. This means that the satellite signal to some parts of the United States can come in at an angle as low as 32 degrees to the horizon. Due to this angle, buildings, hills, trees, highway sound blocking walls or other obstacles might block the satellite signal coming from reaching the vehicle receiver antenna and might cause audio cut outs, unless the wireless provider has installed terrestrial repeaters. Reception quality decreases the further north you travel, as the angle of the incoming signal gets smaller. Also adverse weather conditions might affect reception. At this time, in the event of a customer complaint or inquiry on interference noise: Do not replace any parts Do not program or carry out other work on the vehicle Explain to customer about the new Wireless Communications Service (WCS) signals When investigating Satellite Radio cutouts or a temporary loss of reception: Please compare to a similarly equipped vehicle. Keep in mind the roofline of the vehicle, size of the antenna (sharkfin) and location of the antenna on the vehicle will all affect the strength of the reception. Do not compare a Sport Activity Vehicle (SAV) with a high roofline mounted antenna to a different vehicle such as a coupe or convertible with a much lower mounting point of the antenna. Replace no parts Do not prog
NHTSA source summary · Original PDF not reviewed by Recallfolio
?NBT HEAD UNIT ABORTS IMPORT OF CD Whats New: ? G12 (7 Series) removed ? I01 (i3) removed ? Warranty Section updated for removal of G12 and I01 . While importing a CD to the internal music collection of an NBT head unit the process aborts. You will see 'import error' on the radio display when this occurs. NBT Head Unit software
NHTSA source summary · Original PDF not reviewed by Recallfolio
N20, N26, N55, N63TU, S63TU and S55 Engines: Bosch Injector ETK Part Number Error What's New: ? Procedure change: indentifying injector type using an ISTA test plan. . The current version of the ETK incorporates multiple part number errors for the Bosch type injectors. Ordering the injectors by VIN number or manual identification in ETK may result in an incorrect part number.
NHTSA source summary · Original PDF not reviewed by Recallfolio
HEADUNIT NAVIGATION MAPS (HU-H HU-H2 HU-B): The Headunit High (HU-H), also called NBT, began replacing the Car Information Computer (CIC) on certain MY2013 vehicles with option 609 (7/2012+).
NHTSA source summary · Original PDF not reviewed by Recallfolio
"?SERVICE ACTION: TARGETED ILLUMINATION - REPROGRAM CONTROL UNITS . Affected vehicles need to have control units reprogrammed. CCM (Check Control Message) ""Dynamic Light Spot has failed"" for left or right side. Stepper motors in the targeted illumination headlights can become non-functional at their stop limit."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"CHANGE TO PHEV HV BATTERY CELL MODULES. INFORMATION There has been a change to all Generation 3 PHEV high-voltage (HV) battery cell modules. The number of temperatures sensors on the cell modules has decreased from 4 sensors to 3 sensors. This change has to be taken into account when replacing a component within the HV battery that requires the charging or discharging of a cell module with the Deutronic DBL1200HV-60 cell module charger. When connecting the cell module to the charger the number of temperature sensors (NTC's) will need to be changed to 3 for the charger to charge the module correctly. Refer to the DBL1200HV-60 manual for more information (Attached). To verify how many temperature sensors are on the cell module use the ""Diagnosis"" function of the DBL1200HV-60 cell module charger. The example to the right shows 3 temperature sensors. The message ""ZKS not connected"" will be displayed if the incorrect amount of temperature sensors (NTC's) is selected."
NHTSA source summary · Original PDF not reviewed by Recallfolio
?RATTLE/ POPPING FROM REAR HATCH AREA . There are two related but separate issues (only one may be present at a time) during driving, especially on uneven surfaces: A. Clicking noises or squeaking noises from the area of the rear hatch. Or B. A popping sound coming from the area of the rear hatch. Bump stop height: A. Situation A - settling of the bump stops over time allows vibration, rattle of the hatch. B. Situation B - the bump stops may be adjusted too high, putting torsional stress on the hatch, causing flexing (popping) noises.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"?AUTOMATIC TRANSMISSION DRIVEABILITY COMPLAINTS . Hesitant drive off, sluggish driving behavior. The Automatic Transmission (AT) switches into emergency mode and operates only in first gear, Manual shifting (+/-) in Sport Program (using both gear selector and/or shift paddles) is not possible. 44E257 - ""N6 speed sensor: Direction of rotation invalid"" is stored in transmission control module Transmission Control Unit (GKEG3HY) software"
Source components: POWER TRAIN · POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"? NO REGENERATION OF THE DIESEL PARTICULATE FILTER (DPF) This Service Information bulletin supersedes SI B18 03 10 dated November 2010. . The Service Engine Soon lamp is illuminated. The following fault codes may be stored in the DDE: N47T/N57T engine 245700 - Particle filter system: particulate filter highly loaded (Exhaust backpressure high) 245800 - particle filter system - filter is heavily contaminated. (exhaust backpressure is above maximum) M57Y engine 480A Particle filter system - filter is heavily contaminated. (exhaust backpressure is too high) 481A Particle filter system - filter is heavily contaminated. (exhaust backpressure is above maximum) CAUSE 1. Faults with the exhaust system that affect the monitoring of the DPF by the DDE 2. Unfavorable recent driving profile INFORMATIOM During normal driving, there is a continuous regeneration of the diesel particulate filter that takes place at exhaust-gas temperatures between 280 and 350°C (slower oxidation process). The soot particles can only be burned off when the required exhaust-gas temperature has been reached. Under certain driving conditions (i.e., prolonged short trips or an exhaust system which never reaches soot burn-off temperatures), the DPF can become restricted. The DDE will initiate periodic regeneration automatically, at the latest after 600 miles. In vehicles making many short distance journeys, periodic regeneration takes place after only 250-500 miles. The Digital Diesel Electronics control unit evaluates the time for periodic regeneration from the following values: average distance driven average driving speed temperature in the diesel particulate filter values from the exhaust pressure sensor The DDE initiates the regeneration process by decreasing incoming air by the throttle valve, and one or two post injections are executed. This heats the exhaust-gas temperature to approx. 600° C . When the exhaust temp reaches this point: The soot is burned off with the residual oxygen. The
Source components: ENGINE · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"? DIESEL PARTICULATE FILTER (DPF) CLEANING . The following performance issues may be noticed by the customer: CC-Message ""Drive faulty"" Engine jerking or a lack of power over the whole engine speed range Malfunction indicator lamp (MIL) is illuminated The following fault codes may be stored in the DDE: N47T/N57T engine Main Faults: 245700 - Particle filter system: particulate filter highly loaded (Exhaust backpressure high) 258300 - Exhaust backpressure sensor, Signal: Signal too high Secondary Faults: 244C00 - Charging pressure control, control deviation: charging pressure too low/positive deviation 25DA00 - Exhaust gas difference pressure sensor particle filter, Signal: short circuit to plus pole M57Y engine Main Faults: 480A particle filter system 481A particle filter system Secondary Faults: 4530 charging pressure control, control deviation 429A charging pressure control low pressure stage, control deviation Clogged DPF."
Source components: ENGINE · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"? DIAGNOSING NON FUNCTIONING ""eDRIVE"" This Service Information bulletin supersedes SI B12 27 16 dated November 2016. The customer complains that the vehicle will not go into ""eDrive"", and in some cases ""eDrive"" is greyed-out in the control display (CID) and is not selectable. Also, there are no pertinent electric drivetrain fault codes that assist with diagnosis. Possible 12 volt battery failure, Intelligent Battery Sensor (IBS) failure or MSA deactivation."
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:12V/24V/48V BATTERY · ENGINE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"?CCM: ""START/STOP FAILED"": LOSS OF POWER . Malfunction Indicator Lamp (MIL) is illuminated Check Control Message (CCM) states ""Auto Start/Stop function failed"" One or more of the following codes may be stored in the DME fault memory' 120408: ""Charging pressure control: switching off as a subsequent reaction"" 130F20: ""Exhaust camshaft: angular offset to crankshaft outside of tolerance"" 130E20: ""Intake camshaft: angular offset to crankshaft outside of tolerance"" 164040: ""Intake camshaft: Installation faulty"" 164041: ""Exhaust camshaft: Installation faulty"" Incorrect camshafts timing position (in reference to crankshaft). Combustions occurring just as engine is stopping, drive the engine backwards, dragging the belt drive and toothed belt starter motor backwards. High-inertia torque loading on the camshaft sprockets and crankshaft at this point causes slippage, unintentionally adjusting the timing."
Source components: ENGINE · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"?N63, N63TU, N63R, S63 AND S63TU ENGINES: UPPER OIL PAN REMOVAL AND INSTALLATION REPAIR INSTRUCTIONS This Service Information bulletin supersedes SI B11 17 15 dated October 2016. . INFORMATION When removing and/or installing the engine upper oil pan assembly, the oil pan can sustain damage if this operation is not performed correctly. Before loosening or tightening the engine upper oil pan refer to the newly released Repair Instruction 11 13 010 ""Removing and installing/replacing upper oil sump"" in ISTA/D 3.55.2 or higher for the proper procedures. IMPORTANT: The new repair instructions will state one of the following before reinstalling the upper engine oil pan. ""All threads must be cleaned with screw tap"" Or ""Clean all threads with screw tap. Order number 81 43 0 402 559"" Or ""Clean all threads with a thread cutter"". The current repair instruction terminology will be modified to include this information."
NHTSA source summary · Original PDF not reviewed by Recallfolio
?N63T AND S63T ENGINE: VALVE SEAL REPLACEMENT . This SI provides a new tool and a new procedure for the N63TU valve seals replacement. Please refer to the following applicable SIBs before replacing the valve seals. SI B11 07 11 - Turbocharger Failure: Oil Supply and Return Line Blockage and Proper Repairs SI B11 01 13 - N63 and N63TU Engines: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity SI B11 03 13 - Engine Oil Consumption (all models) SI B11 04 13 - N63TU Engine: Engine Oil Consumption If the valve seals are leaking, one of the following will help determine if the seals should be replaced. Smoke from the tailpipe when starting or aggressively accelerating and decelerating the engine Excessive engine oil consumption Spark plugs fouled with engine oil.
NHTSA source summary · Original PDF not reviewed by Recallfolio
?SERVICE ACTION: CHECK CHARGING OF THE HIGH VOLTAGE BATTERY Please perform the procedure outlined in this Service Information on all affected vehicles prior to customer delivery, or the next time the vehicle is in the shop.
NHTSA source summary · Original PDF not reviewed by Recallfolio
?SERVICE ACTION: REAR SIDE WINDOWS MAY NOT BE PROPERLY AFFIXED TO BODY. Please perform the procedure outlined in this Service Information on all affected vehicles before customer delivery. In the event the customer has already taken delivery of the vehicle, please perform the procedure the next time the vehicle is in the shop.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · VISIBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SI B65 09 15 November 2016 Audio, Navigation, Monitors, Alarms,SRS Technical Service NBT Head Unit High (HU-H) Resets Intermittently or Permanently. The Head Unit-High (HU-H) resets intermittently or permanently. 1. The display is inoperative and there is no audio output 2. Automatic system start-up after a couple of seconds Fault Code E1C440 set No Fault Codes set Software error in the Head Unit High (HU-H)
NHTSA source summary · Original PDF not reviewed by Recallfolio
"SME FAULT CODE 21F21F. The fault code (FC) ""21F21F - High-voltage system: Monitoring of insulation resistance deactivated due to fault of the safety box"" is stored in the battery management electronics (SME). The fault does not set any CCM's, is not perceivable to the customer and has no effect on the complete vehicle operation. Safety box malfunction"
NHTSA source summary · Original PDF not reviewed by Recallfolio
"NBT-EVO Head Unit Cannot Be Swapped Between Vehicles for Testing This Service Information bulletin supersedes SI B65 13 16 dated July 2016.. If an NBT-EVO head unit is swapped into a different vehicle it will enter a locked mode once it recognizes a different VIN. This will set a fault in the Head Unit (NBT-EVO), Fault Code ""B7F87A: Burgler Actively Registered / Component Protection Active"" This will require REPLACEMENT of the head unit to restore operation. To prevent easy re-use of stolen Head units additional features are introduced with 11/15 ISTA/P software to bring NBT-EVO to a higher security level. In NBT-EVO the mechanism is called ""Trusted VIN"""
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Third Row of Seats Blower is Inoperative. The blower in the third row of seats is not working and the fault code ""E70C32 - AC-LIN: Heating in third row of seats is not responding"" has been entered in the IHKA (Integrated Heating and Airconditioning, Automatic) control unit. CAUSE LIN BUS short or open circuit in wiring or connectors Blower motor, micro switch defective Control unit, A/C, for 3rd seat row defective"
Source components: ELECTRICAL SYSTEM · EQUIPMENT:APPLIANCE:AIR CONDITIONER · SEATS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"HEADLIGHT ASSEMBLIES HAVE VISIBLE INTERNAL MOISTURE/CONDENSATION. Water on the inside (A) or misting (B) of both headlight lenses that is visible from outside. Water inside the headlights can be caused by two situations: Water/moisture ingress into the headlight housing. Thermal conditions that result in the formation of condensation. Note: An important indication that the moisture issue is caused by ""condensation"" rather than a ""water leak"" into the headlight housing, there will be misting/condensation in ""both headlights."""
NHTSA source summary · Original PDF not reviewed by Recallfolio
"FC 44E4D1 stored in Transmission Control Unit, either: 1. When no other fault codes stored. ? Customer has seen no performance issues. OR 2. When any of the following fault codes are stored. 44D141 - transmission monitoring: Clutch A and D implausible 44D0E1 - transmission monitoring: Clutch B implausible 44D191 - transmission monitoring: Clutch C and D implausible 44D151 - transmission monitoring: Clutch A and E implausible 44D0D1 - transmission monitoring: Clutch A implausible 44CFB1 - transmission monitoring: Clutch A, D and E implausible 44CFD1 - transmission monitoring: Fault pattern - gear monitoring implausible And possibly: ? Customer reports harsh shifting ? Check Control message ""Drivetrain malfunction"" Various"
NHTSA source summary · Original PDF not reviewed by Recallfolio
"DIAGNOSING NON FUNCTIONING ""eDRIVE"". The customer complains that the vehicle will not go into ""eDrive"", and in some cases ""eDrive"" is greyed-out in the control display (CID) and is not selectable. Also, there are no pertinent electric drivetrain fault codes that assist with diagnosis. Possible 12 volt battery or Intelligent Battery Sensor (IBS) failure."
NHTSA source summary · Original PDF not reviewed by Recallfolio
KAFAS CAMERA-BASED ASSISTANCE SYSTEM LIMITS. INFORMATION The situations described above may all be caused by known limitations of the system such as: Dirty windshield Incomplete calibration process Unsuccessful calibration Restricted visibility- weather conditions or parked vehicles Missing lamps on target vehicle Non-standard vehicle exterior surfaces Insufficient ambient lighting Abrupt motion of target vehicle.
Source components: ENGINE · LANE DEPARTURE: SENSING SYSTEM: OTHER · SERVICE BRAKES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"NBT NAVIGATION DOES NOT ROUTE ON TOLL ROADS. NBT Navigation does not provide routes that include certain toll roads. CAUSE Roads that have toll lanes ""without a cash option"" where not utilized for routing in NBT map data versions: NEXT 2015-1 NEXT 2015-2 NEXT 2016-1 As an enhancement, the NEXT 2017-1 map release now provides information about toll lanes ""without cash option"". UPDATE Install new map data."
NHTSA source summary · Original PDF not reviewed by Recallfolio
?AUDIO VOLUME NOT RESTORED AFTER MSA STOP, ENTRY HEAD UNIT. Volume of audio system (when set to near maximum) is reduced when Auto Start-Stop (MSA) stop occurs and is not restored upon automatic engine restart. This is normal system behavior - serves to protect the head unit, battery drain and avoidance of incremental leaps in the loudness. The loudness is reduced to 2/3 of maximum and is not restored. Note: Air conditioning output is also reduced upon MSA stop and is not restored for similar reasons.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CBS BRAKE PAD CALCULATION AND CORRECTION. When a vehicle comes into the workshop for any repair or maintenance job, the bundling calculator recommends a brake maintenance checkup. No brake warning light is illuminated. CBS shows 3,107 miles or slightly higher for the next brake service displayed via Key Reader, or vehicle's Control Display (in Vehicle Info/Status/Service required/Brake pads) CAUSE CBS calculates the remaining brake pad wear based on brake pressure, speed, vehicle specific parameters (i.e. NAO pads), brake temperature as well as cumulative brake application time. Due to variation of these parameters and outside environmental influences, this calculation can deviate from the real brake pad wear. Starting from the above-mentioned production dates of the vehicles indicated, the CBS brake pad wear calculation has been changed, and is now based only on the brake pad wear sensor. Important Note: To avoid a too-slow wear prediction, the CBS brake model will estimate the need for repairs, in some cases, rather early. Calculation will level at 3,107 miles and stay at this value until the CBS brake pad wear sensor is triggered. https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/36...11/8/2016 Page 2 of 2 After the sensor is triggered, the CBS mileage will count down indicating to the customer that the brake repairs will be due.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SHUDDER OR JERKING IN 7TH AND 8TH GEARS AT 1000 - 1400 RPM. A shudder or slight jerking can be felt when driving with the transmission in 7th or 8th gear and the engine speed is between 1,000 and 1,400 RPM. No related faults are stored and there are not any problems in the chassis systems or with the wheels and tires. This shudder or jerking could begin due to the characteristic power pulses of the N63T engine when it is in VVT mode at low engine loads.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"HVAC BLOWER NOT WORKING This Service Information bulletin supersedes SI B64 12 16 dated August 2016. HVAC blower is not working. Condensation occurs even though blower is working. CC message ""Increased battery discharge"" - standby current violation may be displayed. Climate control unit (IHKA) software"
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE ENGINE SOON (MIL) - SME FC 21F20D. Malfunction Indicator Lamp (MIL) is illuminated. The following codes may be stored in the fault memory of the battery management electronics (SME). 21F20D - SME, safety concept: Switch-off of switch contactors by safety circuit 21F1F6 - High-voltage battery, switch contactors: Switch-off after a fault Software bug: erroneous fault code stored in SME.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CLICKING NOISE FROM FRONT AXLE This Service Information bulletin supersedes SI 31 01 12 dated June 2015. Clicking noises are heard from the front axle area while maneuvering at low speeds (e.g., parking lot maneuvers). CAUSE Movement between the contact surfaces of the wheel bearing and swivel bearing (knuckle)
NHTSA source summary · Original PDF not reviewed by Recallfolio
DDE FAULT CODE: 28DE00 - EXHAUST GAS PRESSURE SENSOR BEFORE TURBINE, PLAUSIBILITY. After performing repairs where the engine harness was disconnected and reconnected at the differential pressure and the exhaust pressure sensor, the following fault is then stored in the DDE: 28DE00 - Exhaust gas pressure sensor before Turbine, plausibility: exhaust gas pressure in front of turbine dynamically not plausible
NHTSA source summary · Original PDF not reviewed by Recallfolio
CHECK CONTROL MESSAGE: NO OIL PRESSURE. Check Control message: Oil pressure warning. Stop carefully is displayed. There are no related faults to oil pressure stored in the DDE. Unfavorable DDE software application When operating during automatic engine start-stop function stop, it may be the case that the oil pressure is incorrectly determined to be too low, which triggers a CC message.
NHTSA source summary · Original PDF not reviewed by Recallfolio
BMW ONLINE NON-FUNCTIONAL: CHECK ICC-ID IN ACCOUNT. The ConnectedDrive Services are non-functional after a hardware exchange of the telematics control unit. This is not indicated by CC-message. ConnectedDrive Services not synchronized by Telematics Control Unit.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"INCORRECT TIRE AND LOADING INFORMATION LABEL. Five (5) vehicles were produced with an incorrect Tire and Loading Information label. The label may not reflect the proper ""Cold Tire Pressure"" specifications for the vehicle. AFFECTED VEHICLES Only the vehicles listed below are affected by this action: VINsMYModelCurrent Address State5UXKR0C5XF0K588942015X5 xDrive35iNew Jersey5UXKR0C57F0K588982015X5 xDrive35iFlorida5UXKR0C54F0K589072015X5 xDrive35iMassachusetts5UXKR0C58F0K589092015X5 xDrive35iNew York5UXKR0C5XF0K589132015X5 xDrive35iVirginia"
NHTSA source summary · Original PDF not reviewed by Recallfolio
INFORMATION ON THE OPERATION OF THE SMART OPENER. INFORMATION ON THE OPERATION OF THE SMART OPENER MODEL F07 (5 Series Gran Turismo) F10 (5 Series) F12 (6 Series Convertible) F13 (6 Series Coupe) F15 (X5) F16 (X6) F22 (2 Series Coupe) F23 ( 2 Series Convertible) F25 (X3) F26 (X4) F30 (3 Series Sedan) F31 (3 Series Wagon) F32 (4 Series Coupe) F33 (4 Series Convertible) F34 (3 Series Gran Turismo) F36 (4 Series Gran Coupe) F48 (X1) F80 (M3 Sedan) F82 (M4 Coupe) F83 (M4 Convertible) F85 (X5 M) F86 (X6 M) G12 (7 Series) I01 (i3 Series) Vehicles with option code SA-0322 (Comfort Access) without M-Sport trim INFORMATION The smart opener (Contactless tailgate) operates as described below: Ignition key must be within 3 feet behind the vehicle, clear from any interference like a smartphone The customer must be at least an arms-length behind the vehicle Kick your foot forwards & backwards under the vehicle in one quick movement The taillights flash confirming that the trunk will open The trunk then successfully opens For more information an instructional video can be viewed which demonstrates the operation. Thanks to BMW of Tenafly for providing the video. tinyurl.com/Autotrunk1 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/358...9/3/2016 Page 2 of 2 WARRANTY INFORMATION Not applicable. [ Copyright (c)2016 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/358...9/3/2016
NHTSA source summary · Original PDF not reviewed by Recallfolio
"A/C FAILURE: FC 801252 ELECTRIC A/C COMPRESSOR: INTERNAL FAULT DETECTED. Air conditioning (A/C) failure with IHKA fault code ""801252 - Electric A/C compressor: Internal fault detected"". IHKA software fault in the versions detailed in the following table: ModelISTA/P versionIntegration levelF153.57.3F025-15-11-505F303.57.2F020-15-11-504I01, I123.57.0I001-15-11-501"
NHTSA source summary · Original PDF not reviewed by Recallfolio
"HVAC BLOWER NOT WORKING. HVAC blower is not working. Condensation occurs even though blower is working. CC message ""Increased battery discharge"" - standby current violation may be displayed. Climate control unit (IHKA) software"
NHTSA source summary · Original PDF not reviewed by Recallfolio
Charging Not Possible - KLE Fault 21E715. The following conditions may exist: Charging is either stopped mid-charge or will not initiate. The corona ring around the charge port blinks red. Check engine light is turned on. Faulty software up to and including ISTA/P 3.58.3 (F025-16-03-504)
NHTSA source summary · Original PDF not reviewed by Recallfolio
NOISE FROM THE FRONT SEAT WHEN ENTERING / EXITING THE VEHICLE. The front seats generate a squeaking noise upon entering or exiting the vehicle. The noise may also occur when repositioning on the seat or movement while driving. Aged/dried leather on the seat bottom cushion rubbing against the plastic side trim.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TAILGATE UNINTENTIONALLY OPENS. Trunk/tailgate may open when vehicle is locked. Trunk/tailgate may open while the vehicle is in motion. Usually after stopping, such as a traffic light etc. Vehicle key trunk/tailgate button may accidentally be pressed, thus opening the tailgate.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Delivery Stop: Remove Engine Oil Label. Affected vehicles in dealer inventory must not be retailed or delivered until the label is removed. Vehicles at ports of entry will be remedied prior to dealer delivery. On affected vehicles, there is an incorrect label regarding the appropriate engine oil. Affected vehicles can be identified with a ""Vehicle Comment"" in the DCS Warranty Vehicle Inquiry or ISPA Light. https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/248...9/3/2016 Page 2 of 2"
NHTSA source summary · Original PDF not reviewed by Recallfolio
CLICKING NOISE FROM FRONT AXLE This Service Information bulletin supersedes SI 31 01 12 dated June 2015. Clicking noises are heard from the front axle area while maneuvering at low speeds (e.g., parking lot maneuvers). CAUSE Movement between the contact surfaces of the wheel bearing and swivel bearing (knuckle)
Source components: BACK OVER PREVENTION · EQUIPMENT · SUSPENSION:FRONT:WHEEL BEARING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Diesel Engine: Intake Manifold Damaged This Service Information bulletin supersedes SI 11 07 16 dated May 2016. The Service Engine Soon light is on. There may also be: Complaints of lack of engine performance An exhaust smell coming from the engine area. The following fault codes may be stored in the DDE: 24CE00 - Hot film air mass meter: Ratio of measured to calculated air mass too high 27F000 - Charge air hose monitoring in idle: Charge air hose fallen down 290900 - Air system, air to EGR air mass flow plausibility: Measured air mass compared to calculated air mass too high 290A00 - Air system, air to EGR air mass flow plausibility: measured air mass compared to calculated air mass too high and high charging pressure control deviation 1. Excessive thermal load from the EGR system on the intake components 2. An excessive or unmetered air leak in the intake/charge air system
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM · FUEL SYSTEM, GASOLINE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Ticking Noise from the Front Axle When Cornering This Service Information bulletin supersedes SI B34 05 15 dated December 2015. The customer may complain of a ticking noise from the front axle when cornering, maneuvering, parking or pulling away from a parking space. The noise can be heard as a metallic ticking from the area of the front wheels. Movement between the inner contact surfaces of the brake disc and drive flange of the wheel bearing hub.
NHTSA source summary · Original PDF not reviewed by Recallfolio
HeadUp Display does not Show Full Street Names. INFORMATION Design of the HUD has limited display area. (It can only show a certain number of text characters). NOTE: Parts replacement or programming the vehicle will not recitify the situation!
NHTSA source summary · Original PDF not reviewed by Recallfolio
"BMW Maintenance Program: 12-Volt Battery Replacement Measure. INFORMATION This bulletin outlines a customer satisfaction measure that has been designed exclusively for the BMW vehicles listed above. It involves the replacement of the 12-volt battery as a preventive maintenance measure. This 12-volt battery replacement measure is: Effective for repairs dated on or after January 1, 2015. Applicable to vehicles that are still covered by the BMW Maintenance Program. This program is valid for 4 years or 50,000 miles, whichever occurs first. The calculation is based on the current date of repair. It is ""applicable"" when the 12volt battery was not replaced within the last 12 months. You can then perform the battery replacement as outlined below. Please check the warranty claim history for the specific vehicle in the DCSnet Warranty Vehicle Inquiry to confirm the battery was not already replaced within the previous 12 months."
NHTSA source summary · Original PDF not reviewed by Recallfolio
Service Action: Program Variable Damper Control (VDC) Unit. Unfavorable tolerances for the plug-in connections of the wheel acceleration sensors may result in fault code memory entries and the VDC being deactivated. If the VDC control unit identifies an implausable value from one of the wheel acceleration sensors, the VDC will be deactivated and the driver is informed by a Check Control message. The vehicle then defaults to the conventional suspension.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Diesel Engine: Intake Manifold Damaged. The Service Engine Soon light is on. There may also be: Complaints of lack of engine performance An exhaust smell coming from the engine area. The following fault codes may be stored in the DDE: 24CE00 - Hot film air mass meter: Ratio of measured to calculated air mass too high 27F000 - Charge air hose monitoring in idle: Charge air hose fallen down 290900 - Air system, air to EGR air mass flow plausibility: Measured air mass compared to calculated air mass too high 290A00 - Air system, air to EGR air mass flow plausibility: measured air mass compared to calculated air mass too high and high charging pressure control deviation 1. Excessive thermal load from the EGR system on the intake components 2. An excessive or unmetered air leak in the intake/charge air system
Source components: ENGINE · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Bluetooth Connection Failures. There are various connectivity failures with the following devices: Apple iPhones Samsung S6 and the S6 Edge. Connectivity failure examples are: Call disconnection - Call is transferred back to the handset. In some instances the call is then transferred back to the vehicle. Contact List incomplete General connection failures Apple iOS software (issue started with iOS 8.3 continues with iOS 9.x and its variants) Samsung S6 and S6 Edge device firmware.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"""Collision Warning Failed"" or ""Pedestrian Warning Failed"" CCM Display. While driving, a Check Control Message (CCM) is displayed advising of the following: Front collision warning failed Pedestrian detection failed The following fault code is stored in the KAFAS (Camera-based Driver Assistance System): 0X800AC4 - Camera calibration failed The KAFAS camera is not properly mounted and secured to the mounting bracket on the windshield; And/ or: The mounting bracket glued to the windshield is not installed correctly. The pictures below show both incorrect and correct installation. This picture shows the KAFAS camera installed in the bracket. Notice the spacing highlighted by the ""green lines"""
NHTSA source summary · Original PDF not reviewed by Recallfolio
Airbag (SRS) Warning Lamp Illuminated. Airbag lamp (SRS) is illuminated and both of the following fault codes are stored: 930904 - Airbag driver stage 1: Resistance too large 93090A - Airbag driver stage 2: Resistance too large CAUSE Coil spring cassette damage.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Incomplete AdBlue Check Control Message (CCM) on the Central Information Display. An incorrectly displayed AdBlue (Diesel Exhaust Fluid refill range) CCM is shown on the Central Information Display. Improper instrument cluster software
Source components: ENGINE · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Charging Not Possible - KLE Fault 21E693. The following conditions may exist: Charging is either stopped mid-charge or will not initiate. The corona ring around the charge port blinks red. Check engine light is turned on. Faulty software up to and including ISTA/P 3.58.3 (F025-16-03-504)
NHTSA source summary · Original PDF not reviewed by Recallfolio
Passenger Side Mirror Dimming Feature Operational Change. INFORMATION The automatically dimming exterior mirror function on the passenger's side has been deleted from the Option Code 430 as noted above. The automatic dimming function will continue to be operational on the driver's side mirror and rear view mirror.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"F15, F30 PHEVs- Gear Selector Plausibility Faults. The Check Control message ""Drive: Stop carefully"" (CCM-ID: 569) is displayed. The following fault codes may be stored in the transmission EGS control module (GKEG3HY3): 44D663 - Position plausibility: Driver's choice N/P from D/R not executed CF1701 - Gear selector switch interface, communication failure CF17A1 - Message missing: receiver EGS (A-CAN), transmitter selector switch (A-CAN) EGS software diagnostic function"
Source components: POWER TRAIN · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM) · POWER TRAIN:AUTOMATIC TRANSMISSION:GEAR POSITION INDICATION (PRNDL).
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Delivery Stop - Transmission Oil Cooler Lines Incorrectly Routed. A Delivery Stop has been issued for fifteen F15 vehicles produced from March 3, 2016 to March 28, 2016. In these vehicles the cooler lines for the automatic transmission may have been routed incorrectly. In such instances, the cooler lines may come into contact with the crankshaft vibration damper (pulley). Affected vehicles can be identified with a ""Vehicle Comment"" in DCS Warranty Vehicle Inquiry or ISPA Light with the description: ""A Delivery Stop has been issued for this vehicle. Dealers must ensure that all Campaigns are completed before retail delivery to the customer. See Service Information Bulletin B17 01 16."""
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION · POWER TRAIN:AUTOMATIC TRANSMISSION:COOLING UNIT AND LINES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Service Action: Program control units (DME data status). The high-voltage battery's life may be reduced when charging the high-voltage battery while the vehicle is in motion. AFFECTED VEHICLES Certain VINs (not all) produced between August 7, 2015 and April 19, 2016. Please check the key reader or the Warranty Vehicle Inquiry screen in DCSnet. The charging strategy incorporated in the DME software.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"N63, N63TU and N63R Engines: Upper Oil Pan Removal and Installation Repair Instructions This Service Information bulletin supersedes SI B11 17 15 dated August 2015.. INFORMATION When removing and/or installing the engine upper oil pan assembly, the oil pan can sustain damage if this operation is not performed correctly. Before loosening or tightening the engine upper oil pan refer to the newly released Repair Instruction 11 13 010 ""Removing and installing/replacing upper oil sump"" in ISTA/D 3.55.11 or higher for the proper procedures. IMPORTANT: The new repair instructions will state one of the following before reinstalling the upper engine oil pan. ""All threads must be cleaned with screw tap"" Or ""Clean all threads with screw tap. Order number 81 43 0 402 559"" Or ""Clean all threads with a thread cutter"". The current repair instruction terminology will be modified to include this information."
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOS Malfunction Is Displayed In Kombi Sporadically. After engine start-up, a CCM (Check Control Message) for SOS malfunction is displayed in the Kombi and in the CID (Central Information Display). One or more of the fault codes below may be stored in the TCB or Combox control unit: 0xB7F32B - GSM Antenna: Open Circuit 0xB7F31F - GSM Antenna: Short to ground 0xB7F31E - GSM Antenna: Open Circuit A signal error is identified during the aerial self-test performed by the TCB (Telematic Control Box or the Combox).
NHTSA source summary · Original PDF not reviewed by Recallfolio
"The Low Washer Fluid Warning Light is illuminated when the Washer Fluid Tank is Full. The low washer fluid warning light is illuminated even though the washer fluid tank is full. There are no faults stored in the system for the washer fluid level switch. CAUSE A non-approved washer fluid is used (fluids that contain a silicone additive, normally colored other than blue). INFORMATION The washer fluid level sensor is a contactless capacitive sensor. The sensor sends a low fluid level signal to the gateway module (FEM - Front Electronics Module or BDC - Body Domain Controller) which in turn displays a low washer fluid warning in the instrument cluster. The use of a ""non-approved"" washer fluid (silicone-based fluid) can cause the low fluid warning light to come on even when the reservoir is full. Refer to ISTA document ""FB-GZ-B17A-F20 Washer fluid level sensor"" for information on how this capacitive sensor operates."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"""Comfort Access Restricted"" Check Control Message is Displayed. ""Comfort Access Restricted"" CCM (Check Control Message) is permanently displayed.. The CCM ID: D0h. The comfort access is functioning correctly. No comfort access aerial fault codes stored in the BDC (Body Domain Controller). Software error in the BDC"
NHTSA source summary · Original PDF not reviewed by Recallfolio
"NBT-EVO Head Unit Cannot Be Swapped Between Vehicles for Testing. If an NBT-EVO head unit is swapped into a different vehicle it will enter a locked mode once it recognizes a different VIN. This will require REPLACEMENT of the head unit to restore operation. To prevent easy re-use of stolen Head units additional features are introduced with 11/15 ISTA/P software to bring NBT-EVO to a higher security level. In NBT-EVO the mechanism is called ""Trusted VIN"""
NHTSA source summary · Original PDF not reviewed by Recallfolio
NBT and Entry Head Unit Software Update for Improved Satellite Radio Reception. Poor Satellite Radio reception CAUSE After this software update there is a slight improvement in Satellite Radio reception for these vehicles when receiving their signal from XM Satellites. This is due to the changeover from Sirius Satellite broadcasting to XM Satellite broadcasting in 2016 (See SI B65 19 15).
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
NHTSA source summary · Original PDF not reviewed by Recallfolio
NBT Head Unit Aborts Import of CD. While importing a CD to the internal music collection of an NBT head unit the process aborts. You will see 'import error' on the radio display when this occurs. NBT Head Unit software
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
NHTSA source summary · Original PDF not reviewed by Recallfolio
"False Alarms of the Anti-Theft Alarm System. The alarm (DWA) siren continues to activate after locking vehicle An ""unapproved"" device is connected to the On-Board Diagnostics (OBD) port of the vehicle. This keeps the Ethernet communication line active which triggers the alarm when the vehicle tries to enter sleep mode."
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:ANTI-THEFT DEVICES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Air Conditioning Refrigerant R1234yf Introduction. Highlights of R-1234yf Meets SAE J2888_201301 ""This SAE Standard covers fittings, couplers, and hoses intended for connecting service hoses from mobile air- conditioning Systems to service equipment such as charging, recovery and recycling equipment"" New tools and equipment are required. To service vehicles equipped with R-1234yf refer to SI B04 02 16. Air conditioning technician certification is required to work on system. Refer to your State Law. Unique low and high side fittings. Revised evaporator core as per SAE J2842. System will use about 5% more refrigerant than a comparable R134a system. System oil is a specific PAG oil. Refer to ISTA repair recommendation. Do not interchange components between systems using other refrigerants. Do not reuse Seals / O-ring material from another system. The system piping has internal heat exchangers (IHX or IWT) as introduced in the G12 (7 series). SAFETY INFORMATION Several precautions need to be observed when working on automotive air conditioning systems: Always wear eye protection and gloves while handling refrigerant or servicing air conditioning system. Avoid breathing R1234yf lubricant vapor or mist. Use only approved service equipment to discharge A/C systems. If refrigerant or compressor oil contacts the skin or eyes, large quantities of cool water should be used to flush the affected area. Never heat a refrigerant container with an open flame. Keep all refrigerant away from open flames. Under no circumstances should R1234yf service equipment or vehicle A/C systems be pressure tested or leak tested with air/R1234yf mixtures. NOTE: The use of compressed air (shop air) for leak detection in an R1234yf system can contaminate the system and/or refrigerant with moisture. Leak detection equipment that meets the SAE J2791 standard will work with R1234yf Never use fittings for an R12 or R134a system on an R1234yf system. Any difficulty in connecting service equipm
NHTSA source summary · Original PDF not reviewed by Recallfolio
SI B84 03 14 February 2016 Communication Systems Technical Service This Service Information bulletin supersedes SI B84 03 14 dated October 2014. SUBJECT Bluetooth Connection Failures. There are various connectivity failures with the following devices: Apple iPhones Samsung S6 and the S6 Edge. Connectivity failure examples are: Call disconnection - Call is transferred back to the handset. In some instances the call is then transferred back to the vehicle. Contact List incomplete General connection failures CAUSE Apple iOS software (issue started with iOS 8.3 continues with iOS 9.x and its variants) Samsung S6 and S6 Edge device firmware CORRECTOPM None available at this time. We are currently working with the device manufacturer on a solution.
Source components: ELECTRICAL SYSTEM · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUBJECT Audio System Speaker Testing. For audio system speaker testing there is a NED (Non Electrical Diagnosis) Test Plan available. CAUSE We previously recommended use of the Audio Test CD (ATC) from BMW. This CD has been discontinued.
Source components: ELECTRICAL SYSTEM · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
February 2016 General Electrical Systems Technical Service This Service Information bulletin supersedes SI B61 03 14 dated May 2015. SUBJECT Check Control Messages Related to Battery Charge during Cold Ambient Temperatures. On cold days (an outside ambient temperature below 15F), customers may notice a check control message related to the battery displayed on the instrument cluster and the control information display. The check control message (ID 229) is caused by a heavily discharged battery. The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit).
NHTSA source summary · Original PDF not reviewed by Recallfolio
SI B36 01 15 February 2016 Wheel and Tires Technical Service This Service Information bulletin supersedes SI 36 01 15 dated October 2015. designates changes to this revision SUBJECT Check Control Message: Tire Pressure Monitor (RDCi) Failure. A Check Control Message states Tire Pressure Monitor (RDCi) has failed CAUSE Hardware in the remote control unit (FBD3 antenna)
Source components: EQUIPMENT · TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SI B13 03 15 February 2016 Fuel Systems Technical Service This Service Information bulletin supersedes SI B13 03 15 dated March 2015 and replaces SI B13 04 13 dated March 2014. SUBJECT N20, N26, N55, N63TU, S63TU and S55 Engines: Bosch Injector ETK Part Number Error. The current version of the ETK incorporates multiple part number errors for the Bosch type injectors. Ordering the injectors by VIN number or manual identification in ETK may result in an incorrect part number.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The DDE software application for exhaust gas recirculation control (EGR) does not favorably match the diesel fuel grades available in many parts of the US market. The high pressure EGR cooler could become filled with soot particulate to the point that exhaust gas flow and cooling efficiency are significantly reduced. This could result in the Service Engine Soon light coming on with EGR control / Air mass faults being stored in the DDE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Under certain engine operating conditions the measured air mass between the cylinder banks 1-4 and 5-8 is miscalculated by the DME's. This could result in incorrect engine torque and mismatched ignition parameters with the possibility of internal engine damage.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Whistling Noise Coming from the Center Vent - A/C is Off . A very high pitched whistling or beeping noise is heard coming from the center vents. The flow of refrigerant through the expansion valve at certain temperature differentials.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Instrument Cluster Multifunction Display Intermittently Blank . Some information displays in the Instrument Cluster (KOMBI) may intermittently go blank. This may include the tachometer and speedometer displays. There is a software error in the KOMBI.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Vehicles which have had the Instrument Cluster (KOMBI) replaced may display incorrect CBS (Condition Based Service) data after programming. AFFECTED VEHICLES Vehicles which require this Service Action to be completed will show it as ""Open"" when checked either in the ""Service Menu"" of DCSnet (Dealer Communication System) or with the Key Reader. Incorrect SW calibration loaded after KOMBI replacement."