2013 BMW X5 Manufacturer communications & TSBs.Page 3
Original record summaries, dates and identifiers for this model-year. Records 201–271 of 271, ordered newest first. Dated records on this page: Aug 1, 2012–Apr 1, 2014.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Apr 1, 2014Service Bulletin/Repair Instructions
650514
NHTSA communication ID: 10148276
NHTSA source summary · Original PDF not reviewed by Recallfolio
Traffic Information Is Inoperative. The traffic information is intermittently or permanently inoperative. * Traffic flow is not displayed on the navigation map. * The traffic list is empty. 1. The Offboard Availability (backend) system is unavailable and is not sending traffic information. 2. The traffic information feature is not activated correctly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored: * 213901 - Power management: Reduction or shutdown of individual electrical consumer * 8040BD - Reset or deactivation of Terminal 30F * 8040B9 - De-activation of terminal 30B: Top start capability limit reached * 8020E8 - Reset or deactivation of terminal 30F * 800E89 - FRM: start capability limit reached with lights active during stationary mode * 93076B - Deactivation of terminal 30B: upper start capability limit reached * 93076A - Deactivation of terminal 15: upper start capability limit reached, but deactivation preventer active * 93076C - Deactivation of terminal 30B: upper start capability limit reached, but deactivation preventer or legal loads active * 930769 - Deactivation of terminal 15: upper start capability limit reached Note: When the outside temperatures drop below 46F, the charging system is switch to full charge. CAUSE * The check control message (ID 229) is caused by a heavily discharged battery. * The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). * In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. * Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. * The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
A customer may complain of a delay in engine response after decelerating at low road speeds and then reaccelerating. This can occur when the transmission remains in a high gear due to a delay in the transmission downshifting. This situation can be more noticeable while driving on roads with slight turns or with an increasing gradient. Unfavorable EGS and DME software
Source components: ELECTRICAL SYSTEM:SOFTWARE · ENGINE · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
N63 and S63 Engine: High-pressure Fuel Injector Replacement Procedures. The customer complains that one of the following scenarios has been encountered while operating the vehicle: * During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. * During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated. While driving or idling, the engine will misfire and the Service Engine Soon lamp is illuminated. * Various misfire faults are stored in DME fault memory. CAUSE An internal failure of the high-pressure fuel injector can lead to incorrect operation.
NHTSA source summary · Original PDF not reviewed by Recallfolio
N52T / N55 with 8HP45: Delay in Engine Response. A customer may complain of a delay in engine response after decelerating at low road speeds and then reaccelerating. This can occur when the transmission remains in a high gear due to a delay in the transmission downshifting. This situation can be more noticeable while driving on roads with slight turns or with an increasing gradient. Unfavorable EGS and DME software
NHTSA source summary · Original PDF not reviewed by Recallfolio
ConnectedDrive/BMW Assist System Information and Availability. ConnectedDrive features are partially or completely inoperative. Examples of some of these features are listed below: * BMW Assist Inoperative ? SOS call ? Roadside Assistance call * My BMW Remote App * BMW Online - Google local search * Concierge CAUSE The Electronic Subscriber Agreement (ESA) is inactive. * No active contract for ConnectedDrive features Offboard Availabilty (Backend) system issues * The external network was/is inoperative. * No data is sent to the vehicle.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"ConnectedDrive/BMW ASSIST Features Are Inoperative. ConnectedDrive features are partially or completely inoperative. * No traffic information (RTTI / ARTTI) * BMW ASSIST ""My Info"" service doesn't work. CAUSE The Electronic Subscriber Agreement (ESA) is inactive. * No active contract for ConnectedDrive features Offboard Availability (Backend) system issues * The external network was/is inoperative. * No data is sent to the vehicle."
NHTSA source summary · Original PDF not reviewed by Recallfolio
Delay in Automatic Driving Light Switching On/Off. When driving out of a tunnel or exiting underground parking, the automatic driving light remains switched on for two minutes, even in daylight. The automatic driving light switching on/off can be shorter or longer when it starts to get dark. CAUSE The software for the switch-on threshold is lowered to protect the xenon light source.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Outside Door Mirror Moves when Locking or Unlocking the Vehicle. The door mirror tilts immediately after unlocking or locking. The mirror position does not correspond to the memory position preset by the customer. Pressing the seat memory button typically will return the mirror to the stored position. Poor electrical contacts of the mirror drive in the mirror housing INFORMATION The problem has been integrated into ISTA diagnostics. Complete the diagnosis test plan using the latest ISTA version. The test plan can be accessed via the following path: ""Information Search / Function Structure / Body / Mirror / Exterior mirrors / Driver's or passenger side / Exterior Mirror https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/15...12/6/2013 Page 2 of 2 Malfunction,"" and then press ""Start Search."" Select the test plan ""AM5102_00010."""
Source components: ELECTRICAL SYSTEM · STRUCTURE · VISIBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
N55: Engine Difficult to Start at Cold Ambient Temperatures. The complaint may include any of the following symptoms: * The engine stalls immediately after a cold start before driving away * The engine may run roughly or misfire after a cold start * The engine does not start cold or may take several attempts * To assist starting when cold, the accelerator may need to be depressed slightly and the idle speed raised for a few seconds so the engine does not stall This can occur most frequently at outside ambient temperatures between -15°C and + 15°C. It is possible that the Service Engine Soon (MIL) lamp is on with misfire fault(s) stored, but it is equally possible that there will be no faults stored in the DME. Unfavorable DME software Cold start or idling problems may arise due to poor fuel quality. The use of summer fuel during cold outside temperatures may also lead to such problems.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Service Action: Retrofit Bracket for EGR Cooler. The flexible pipe on the high-pressure Exhaust Gas Recirculation (EGR) cooler may leak. CAUSE Excessive vibration and/or tension at the flexible elbow of the EGR cooler can cause it to leak.
NHTSA source summary · Original PDF not reviewed by Recallfolio
N63 and S63 Engine: High-pressure Fuel Injector Replacement Procedures. The customer complains that one of the following scenarios has been encountered while operating the vehicle: * During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. * During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated. ??While driving or idling, the engine will misfire and the Service Engine Soon lamp is illuminated. * Various misfire faults are stored in DME fault memory. CAUSE An internal failure of the high-pressure fuel injector can lead to incorrect operation.
NHTSA source summary · Original PDF not reviewed by Recallfolio
N63T Engine: New Test Plan to Check Engine Oil Level with ISTA/D 3.39.21. INFORMATION With the release of ISTA/D 3.39.21, a new test plan is available for checking the engine oil level in some vehicles with the N63T engine. The test plan will help identify the actual oil level, and advise the amount that will need to be added to correctly fill the engine when topping up. When performing the scheduled oil service and filling the engine with the amount specified, the applicable ISTA/D repair instruction does not require performing this test plan. Applicable models: * F01 and F02 with the N63T engine, produced from 3/2013 and later with I-Level F001-13-03-501 or higher * F06, F07, F12 and F13 with the N63T engine, produced from 3/2013 and later with I-Level F001-13-03-501 or higher * F10 with the N63T engine produced from 7/2013 and later with I-Level F010-13-07-501 or higher Test plan path: Service Function/Drive/Motor Electronics/Motor Oil/Oil Level IMPORTANT: Do not perform this test plan on the following vehicles: * E70, E71, F01, F02, F04, F06, F07, F12 and F13 vehicles with the N63 or N63T engine, produced before 3/2013 l * F10 vehicles with the N63 engine produced before 7/2013 If this test plan is performed on these vehicles, the result is an incorrect measurement and level indication; overfilling of the engine will occur. Overfilling of the engine will result in engine damage. When a solution for vehicles which are not at one of the integration levels above is available, it will be communicated promptly. WARRANTY INFORMATION Not applicable. [ Copyright (c)2013 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/15702.1.B11071... 11/12/2013
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Service Action: Retrofit Bracket for EGR Cooler. The flexible pipe on the high-pressure Exhaust Gas Recirculation (EGR) cooler may leak. CAUSE Excessive vibration and/or tension at the flexible elbow of the EGR cooler can cause it to leak. VEHICLES AFFECTED This Service Action involves certain E70 vehicles with the M57Y engine which were produced from 10/2011 to 7/2012. In order to determine whether a specific vehicle has had this Service Action completed or is affected by this Service Action, first check the B-pillar label for code number 651. If code number 651 has been punched out, the campaign has already been performed. If code number 651 has not been punched out, it will be necessary to utilize the ""Service Menu"" of DCSnet (Dealer Communication System) or the Key Reader. Based on the response of the system, either proceed with the corrective action or take no further action."
NHTSA source summary · Original PDF not reviewed by Recallfolio
BMW: SOME VEHICLES MAY EXPERIENCE HIGH PRESSURE EXHAUST GAS RECIRCULATION (EGR) COOLER LEAKING FROM FLEXIBLE PIPE, DUE TO EXCESSIVE VIBRATION AND/OR TENSION AT FLEXIBLE ELBOW OF EGR COOLER. MODEL E70 (XDRIVE35D). NO MODEL YEAR. *PE UPDATED 1/28/14. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
Window Guide Is Pushed up and Distorted. The customer may notice the front window seal looks deformed or distorted in the uppermost area of the window. CAUSE Front window guide fitment gap tolerance to the door frame
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Oil Leak from Turbocharger Charge Air Hose. The customer may complain of an oil leak from the engine area. The ""Service Engine Soon"" lamp may also be illuminated with fault code ""4674 - FMO injection quantities-observer"" stored. CAUSE The molded seal in the charge air pipe may have been cut by debris abrasions, causing an external leak of air and oil in the charged air system of the turbocharger. An improved seal has been developed to correct this issue."
NHTSA source summary · Original PDF not reviewed by Recallfolio
BMW: OIL LEAKS FROM THE AIR HOSE ON TURBOCHARGER. THIS IS DESIGNATED FOR E70, AND E90 MODELS WITH M57Y DIESEL ENGINES. SERVICE ENGINE SOON LAMP MAY BE ILLUMINATED. *KB
Source components: ENGINE AND ENGINE COOLING:ENGINE:DIESEL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Water Leak from the Front of the Sunroof. During extended periods of heavy rain, water may enter the vehicle from the area around the front of the sunroof cassette, the Roof Control Panel (FZD), the map lights, or the A-pillars. The customer may also simply state that the carpet in the front of the vehicle is wet. The sunroof cassette is overflowing due to the fact that one or both of the front sunroof drains are trapped or twisted.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Outside Door Mirror Moves when Locking or Unlocking the Vehicle. The door mirror tilts immediately after unlocking or locking. The mirror position does not correspond to the memory position preset by the customer. Pressing the seat memory button typically will return the mirror to the stored position. Poor electrical contacts of the mirror drive in the mirror housing INFORMATION The problem has been integrated into ISTA diagnostics. Complete the diagnosis test plan using the latest ISTA version. The test plan can be accessed via the following path: ""Information Search / Function Structure / Body / Mirror / Exterior mirrors / Driver's or passenger side / Electrochromic Mirror,"" and then press ""Start Search."" Select the test plan ""AM5102_00010."""
NHTSA source summary · Original PDF not reviewed by Recallfolio
Grating Noise from Side Window Defroster Vent. The customer may notice a grating or creaking noise coming from the instrument panel at the extreme left or right side. It is only heard when the vehicle is in motion. CAUSE The side window defroster vent fitment (in the instrument panel) causes a grating noise when driving, and torsional forces are applied. The driver's or passenger's side can both be affected.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Brake Fluid Maintenance Service: 36-Month Interval. The CBS displays the first brake fluid service as a 36-month interval from the date of production instead of the appropriate 24-month interval.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Clicking Noise from Front Axle. Clicking noises are heard from the front axle area while maneuvering at low speeds (e.g., parking lot maneuvers). CAUSE Movement between the contact surfaces of the wheel bearing and swivel bearing (knuckle)
NHTSA source summary · Original PDF not reviewed by Recallfolio
"?Panoramic Sunroof Repair Instructions. INFORMATION Sunroof Repair Instructions: The panoramic sunroof contains several ""mechanism sets"" which can be repaired and/or replaced independently in the event of a mechanical failure. When performing such a repair to any of these sets, the TIS/ISTA Repair Instructions (REP) should always be consulted. Due to the complex nature of these repairs, a set of complementary instructions with additional detail, explanation, and photos has been developed. The attached Repair Instructions should always be used in conjunction with the TIS/ISTA REP. "
NHTSA source summary · Original PDF not reviewed by Recallfolio
Brake Fluid Maintenance Service: 36-Month Interval. The coding in these vehicles has the CBS displaying the first brake fluid service as a 36-month interval from the date of production, instead of the appropriate 24-month interval.
NHTSA source summary · Original PDF not reviewed by Recallfolio
N55: Idle Fluctuates Briefly After a Cold Engine Start. Under certain engine cold starts, the engine idle may fluctuate during the first 10-20 seconds of operation before becoming stable. No faults will be stored in this situation, which will usually only occur at specific engine temperatures, making it difficult to reproduce in the workshop. Unfavorable DME software calibration
NHTSA source summary · Original PDF not reviewed by Recallfolio
Steering Column Automatic Adjustment Is Inoperative. The steering column automatic adjustment, when leaving and entering the vehicle, is inoperative. The steering column manual adjustment works properly. CAUSE CAS (Car Access System) error: Electric steering column adjustment is not initialized. No faults codes are stored in the system.
NHTSA source summary · Original PDF not reviewed by Recallfolio
A customer may complain of a delay in engine response after decelerating at low road speeds and then reaccelerating. This can occur when the transmission remains in a high gear due to a delay in the transmission downshifting. This situation can be more noticeable while driving on roads with slight turns or with an increasing gradient. Unfavorable EGS and DME software
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Panoramic Sunroof Repair Instructions. INFORMATION Sunroof Repair Instructions: The panoramic sunroof contains several ""mechanism sets"" which can be repaired and/or replaced independently in the event of a mechanical failure. When performing such a repair to any of these sets, the TIS/ISTA Repair Instructions (REP) should always be consulted. Due to the complex nature of these repairs, a set of complementary instructions with additional detail, explanation, and photos has been developed. The attached Repair Instructions should always be used in conjunction with the TIS/ISTA REP. Refer to the following repair attachments: Front Glass Mechanism repair E53, E61, E70, E83, E91.pdf Rear Glass Mechanism repair E53, E61, E70, E83, E91.pdf Wind Deflector Mechanism repair E53, E61, E70, E83, E91.pdf Sunshade Mechanism repair E53, E61, E83.pdf Sunshade Mechanism repair E70, E91.pdf All panoramic roofs for the above-listed models are conceptually similar and utilize similar repairs. NOTE: An E83 (X3) sunroof cassette is used for demonstration of the repairs. Some differences may exist between this and other models. The following prerequisite work is required in order to replace the following kits (in addition to removing the cassette from the car and glass from the cassette): Front Glass Mechanism - None. Rear Glass Mechanism - Remove the front glass mechanism. Wind Deflector Mechanism - Remove the front glass mechanism; remove the rear glass mechanism. Sun shades and Shade Mechanism - None Sunroof Mechanical 3D Animation: A 3D animation has been developed in order to clarify how the sunroof mechanism operates, as well as how it is assembled and disassembled. To view this animation, open Interactive Career Pathways (ICP) and select ""Replace Front and Rear Glass Panel Mechanic"" from the Technical Service Information section of the home page. This animation allows you to: * Operate the mechanism and view from any angle; * Add or remove parts and then cycle the sunroof; * S
NHTSA source summary · Original PDF not reviewed by Recallfolio
Rattle Noise from Rear Seat Backrest. A rattle noise can be heard from the rear seat area when the vehicle is driven. CAUSE The left and right rear seat backrest locks have insufficient lubrication.
NHTSA source summary · Original PDF not reviewed by Recallfolio
DSC Warning Light is On. The warning lamps for DSC, ABS and brake warning are illuminated. There may also be a warning in the control display for 'Chassis Control System failure' One or more of the following fault codes are stored: F25, F30 DSC * D36D44 - Signal error longitudinal torque distribution (LMV) * 48097D - Transfer Case clutch position open F01, F02, F07, F10, F12 and F13 LMV: * 440108 - Control Unit internal error * 44010F - Control Unit internal error E70, E71 and E84 LMV: * 5219 - Control Unit: EEPROM Writing-reading-error * 522D - Control Unit: internal Error CAUSE Software calibration error in the LMV
NHTSA source summary · Original PDF not reviewed by Recallfolio
"The warning lamps for DSC, ABS and brake warning are illuminated. There may also be a warning in the control display for ""Chassis Control System failure."" One or more of the following fault codes are stored: DSC: * D36D44 - Signal error longitudinal torque distribution (LMV) * 48097D - Transfer Case clutch position open F01, F02, F07, F10, F12 and F13 LMV: * 440108 - Control Unit internal error * 44010F - Control Unit internal error E70, E71 and E84 LMV: * 5219 - Control Unit: EEPROM Writing-reading-error * 522D - Control Unit: internal Error CAUSE Software calibration error in the LMV"
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
N52T/N55 with 8HP45: Delay in Engine Response. When slowing down to lower suburban road speeds and then accelerating, a delay in engine response may be experienced. This situation may be more noticeable when driving in a bend in the road or on roads with a rising gradient. Unfavorable EGS and DME software calibration
NHTSA source summary · Original PDF not reviewed by Recallfolio
N63 and S63 Engine: High-pressure Fuel Injector Replacement Procedures. The customer complains that one of the following scenarios has been encountered while operating the vehicle: * During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. * During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated. ??While driving or idling, the engine will misfire and the Service Engine Soon lamp is illuminated. * Various misfire faults are stored in DME fault memory. CAUSE An internal failure of the high-pressure fuel injector can lead to incorrect operation.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Service Action: Program Control Units (Auto Hold Response). Based on the accelerator pedal request, the engine's response may not be fulfilled on hills if the ""Auto hold"" function is activated. CAUSE DME software error"
NHTSA source summary · Original PDF not reviewed by Recallfolio
N63: Drop in Engine Speed While Turning at Low Speeds. The engine speed may drop significantly below normal idling speed if the steering wheel is turned sharply at lower road speeds. Unfavorable DME software
NHTSA source summary · Original PDF not reviewed by Recallfolio
"N63 and N63T Engine: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity. Customers with one of the vehicles above may complain that the engine's oil consumption is ""too high,"" resulting in engine oil top-ups and workshop visits to address the issue before the vehicle displays an engine oil service as being ""due."" When the vehicle's engine oil drops to the minimum level, a message will display in the vehicle advising the driver to ""add 1 quart of engine oil."" After topping up and continued operation, the ""add engine oil"" message may display again before an engine oil service is required and performed. CAUSE Engines that are fitted with a turbocharger, as part of their normal operation, will consume engine oil at a higher rate than a naturally aspirated engine (non-turbocharged engine). In this case, a ""turbocharged"" engine could require topping up of the engine oil more frequently."
NHTSA source summary · Original PDF not reviewed by Recallfolio
BMW: WHILE ON HILLS, ENGINE RESPONSE MAY NOT BE FULFILLED, WHEN ACCELERATOR PEDAL IS DEPRESSED AND IF AUTO HOLD FUNCTION IS ACTIVATED. MODELS 2010-2013 E70, E71. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
Intermittently, the engine idle speed may fluctuate up and down or cut off under any of the following circumstances, without any relevant faults stored in the DME memory: * While driving off throttle (coasting) and braking at speeds below approx. 10 mph * While idling, low-speed maneuvering such as parking, or if the steering is turned to the full-lock position Unfavorable DME software
NHTSA source summary · Original PDF not reviewed by Recallfolio
MService Action: Replace the Coolant Pump. Coolant is leaking from the coolant pump. CAUSE The coolant pump may develop cracks in the plastic housing. These cracks may result in a coolant leak.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Front or Rear Windshield Wipers Fail to Operate. INFORMATION The following troubleshooting hints are based on known areas that can cause the situations described above to occur. 1. Front windshield wiper failure: perform the following checks only when the front windshield wiper fails to operate. If the rear wipers fail to operate, proceed to section 2. * Check Fuse F44 (30 A) and replace as necessary. * Check connector X333 at the front wiper motor to makes sure it is plugged in correctly, and no corrosion exists at the connection. Repair as needed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Battery Discharged Because of Unfavorable Driving Profile. In certain situations, the battery may become discharged when the vehicle is driven frequently on short trips (less than 3 miles per trip), or when the telephone or entertainment system is used for up to 30 minutes while the vehicle is stationary. CAUSE The vehicle charging system, in extreme conditions, is not able to properly compensate for the excessive discharging of the battery caused by an unfavorable driving profile.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Squeaking Noises from Steering Wheel While Turning. There is a squeaking noise from the steering column when the steering wheel is turned. The rubber boot on the steering column is not positioned correctly or lacks sufficient grease for the plastic bearing. INFORMATION The problem has been integrated into ISTA diagnostics. Follow the diagnosis test plan, using the latest ISTA version. In ""Information Search,"" select the ""Function Structure"" tab. Select ""Chassis and Suspension / Steering / Steering interference noise,"" and then press ""Start Search."" Select test plan ""AM3201_00222 - Steering noises."" The BMW Group has integrated NED (Non-electric Diagnosis) into diagnosis for the purpose of finding the cause of mechanical, acoustic and visual problems. Refer to bulletin B07 03 10 for more details."
NHTSA source summary · Original PDF not reviewed by Recallfolio
Oil Leak from Transfer Case. Oil is leaking from the transmission area, or oil seepage is noticed from the transmission/transfer case area during a service. CAUSE The leak can be misdiagnosed as a transmission fluid leak from either the mechatronics sleeve or transmission oil pan. The leak is actually coming from the transfer case (input or output shaft seal).
NHTSA source summary · Original PDF not reviewed by Recallfolio
N63 and S63 Engine: High-pressure Fuel Injector Replacement Procedures. The customer complains that one of the following scenarios has been encountered while operating the vehicle: * During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. * During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated. ??While driving or idling, the engine will misfire and the Service Engine Soon lamp is illuminated. * Various misfire faults are stored in DME fault memory. CAUSE An internal failure of the high-pressure fuel injector can lead to incorrect operation.
NHTSA source summary · Original PDF not reviewed by Recallfolio
N55 Engine Failsafe - FC 120308 Boost Pressure Control, Plausibility: Pressure Too Low Stored in DME Fault Memory. INFORMATION The customer complains the SES is illuminated and the engine has reduced power (engine failsafe mode).
NHTSA source summary · Original PDF not reviewed by Recallfolio
BMW: BATTERY HAS AN INCREASED DEMAND DUE TO DEVELOPEMENTAL PROCESS OF THE ELECTRICAL SYSTEM. THIS IS CAUSING THE BATTER TO NEED TO UNDERGO AN ENERGY DIAGNOSIS. *KB
NHTSA source summary · Original PDF not reviewed by Recallfolio
BMW: BATTER DISCHARGED BECAUSE OF UNFAVORABLE DRIVING PROFILE. THIS IS CAUSED ON SHORT TRIPS (LESS THAN 3 MILES) OR WHEN THE TELEPHONE OR ENTERTAINMENT SYSTEM IS USED FOR UP TO 30 MINUTES WHILE VEHICLE IS STATIONARY. MODELS X5, X6 ALL MODEL YEARS AFFECTED. *KB
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:12V/24V/48V BATTERY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various Faults Concerning the Automatic Tailgate Operation. Complaints of sporadic or permanent faults may exist with the automatic tailgate function. One or more of the following fault codes have been stored: A2AB, A2B1, A2B2, A2B3, A2B4, A2B5, A2B6, A2B7, A2B8, A2B9, A2BA, A2BC, A2BE, and A6E2. CAUSE The following four main faults are currently known: 1. The lower tailgate does not close completely. 2. The tailgate wiring harness near the hinge area is damaged. 3. Fault in the left or right side electric spindle drive 4. Fault in the tailgate lock. 5. The tailgate lock and tailgate lift drive connectors may have corrosion or discoloration. If any is seen, the part must be replaced.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Outside Door Mirror Moves when Locking or Unlocking the Vehicle. The door mirror tilts immediately after unlocking or locking. The mirror position does not correspond to the memory position preset by the customer. Pressing the seat memory button typically will return the mirror to the stored position. Poor electrical contacts of the mirror drive in the mirror housing INFORMATION The problem has been integrated into ISTA diagnostics. Complete the diagnosis test plan using the latest ISTA version. The test plan can be accessed via the following path: ""Information Search / Function Structure / Body / Mirror / Exterior mirrors / Driver's or passenger side / Electrochromic Mirror,"" and then press ""Start Search."" Select the test plan ""B5116_ECSPPL2."""
NHTSA source summary · Original PDF not reviewed by Recallfolio
Incorrect Accelerator Pedal Module. During vehicle production, certain X5 and X6 models may have been produced with an accelerator pedal module that does not have the stainless steel trim.
NHTSA source summary · Original PDF not reviewed by Recallfolio
N63: Drop in Engine Speed While Turning at Low Speeds. The engine speed may drop significantly below normal idling speed if the steering wheel is turned sharply at lower road speeds. Unfavorable DME software
NHTSA source summary · Original PDF not reviewed by Recallfolio
Incorrect Exhaust Tips Installed. The M Performance option calls for chrome black exhaust tips. Certain E70 and E71 vehicles with the M Performance option were incorrectly built with chrome exhaust tips.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
N63 and S63 Engine: High-pressure Fuel Injector Replacement Procedures. The customer complains that one of the following scenarios has been encountered while operating the vehicle: * During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. * During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated. * While driving or idling, the engine will misfire and the Service Engine Soon lamp is illuminated. * Various misfire faults are stored in DME fault memory. CAUSE An internal failure of the high-pressure fuel injector can lead to incorrect operation.
NHTSA source summary · Original PDF not reviewed by Recallfolio
?SI B11 11 12 January 2013 EngineTechnical Service This Service Information bulletin supersedes SI B11 11 12 dated November 2012. PERFORM THE PROCEDURE OUTLINED IN THIS SERVICE INFORMATION ON ALL AFFECTED VEHICLES BEFORE CUSTOMER DELIVERY OR THE NEXT TIME THEY ARE IN THE SHOP FOR MAINTENANCE OR REPAIRS. BMW centers must ensure recalls are completed after having been notified by BMW of North America, LLC (BMWNA) that a safety-related defect or noncompliance exists in any motor vehicle or item of replacement equipment in the center's possession at the time of notification. In BMW NA's case, this notification would typically be made by the issuance of a recall notification in the form of a Service Information bulletin (SIB) or transmission of a Dealer Communication System (DCS) recall message. Under the National Traffic and Motor Vehicle Safety Act of 1966, as amended, if a recall campaign is announced by BMW NA, centers must ensure that all recalls on new vehicles and new items of replacement equipment are completed BEFORE delivery to the consumer. This means that centers may not legally deliver new motor vehicles or new items of replacement equipment to consumers with an open recall. The Safety Act also prohibits centers from selling or leasing the motor vehicle or item of replacement equipment, unless and until the open recall has been completed BEFORE delivery. This also pertains to vehicles in the Certified Pre-Owned program, and to items of replacement equipment. Finally, BMW centers should not sell or use parts that have been recalled by BMW NA. Please follow the specific instructions provided by BMW NA on the return or disposition of the parts. designates changes to this revision SUBJECT Recall Campaign 12V-550:: Replace Hex Bolt with Internal Thread for Deflection Pulley. One of the alternator attaching bolts may fail. Subsequently the vehicle may lose power steering assist while driving. If power steering assistance is lost, the vehicle will remain control
NHTSA source summary · Original PDF not reviewed by Recallfolio
Service Action: CIC - Install Navigation Road Map Database 2013. The Car Information Computer (CIC) road map database 2013 must be installed onto the CIC internal Hard Disc Drive (HDD).
NHTSA source summary · Original PDF not reviewed by Recallfolio
"CCC - ""Please Insert Navigation DVD"" Appears on CID. The navigation map DVD cannot be read or detected. The message ""Please insert navigation DVD"" appears in the CID (Central Information Display). The navigation system is inoperative. This situation may also occur when upgrading to a new navigation map. The old map is recognized but the new one is not. CAUSE Faulty DVD drive; read error due to hardening of the anti-vibration gel on the read head"
NHTSA source summary · Original PDF not reviewed by Recallfolio
Service Action: Replace the Left and Right Fuel Level Sensor. After refueling, the fuel gauge will display an incorrect fuel level. When this occurs, the fuel gauge shows the fuel level as 3/4 full. CAUSE Due to a high proportion of ethanol in the fuel, the internal mechanisms of the fuel level sensors may swell. This may inhibit the movement of one or both of the fuel level sensors.
NHTSA source summary · Original PDF not reviewed by Recallfolio
BMW: SERVICE ACTION: REPLACE THE LEFT AND RIGHT FUEL LEVEL SENSOR. DUE TO HIGH PROPORTION OF ETHANOL IN THE FUEL, THE INTERNAL MECHANISMS OF THE FUEL LEVEL SENSORS MAY SWELL. THIS MAY INHIBIT THE MOVEMENT OF ONE OR BOTH OF THE FUEL LEVEL SENSORS. *JS
NHTSA source summary · Original PDF not reviewed by Recallfolio
BMW: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. N52K ENGINE DMTL PUMP: EMISSIONS WARRANTY EXTENSIONS TO 10 YEARS/120,000 MILES. BMW HAS BECOME AWARE OF A POTENTIAL PROBLEM WITH THE DURABILITY OF THE TANK LEAK DIAGNOSTIC MODULE (DMTL) PUMP ON MY 2007,2008, AND 2009.*JS
NHTSA source summary · Original PDF not reviewed by Recallfolio
PERFORM THE PROCEDURE OUTLINED IN THIS SERVICE INFORMATION ON ALL AFFECTED VEHICLES BEFORE CUSTOMER DELIVERY OR THE NEXT TIME THEY AREIN THE SHOP FOR MAINTENANCE OR REPAIRS. BMW centers must ensure recalls are completed after having been notified by BMW of North America, LLC (BMWNA) that a safety-related defect or noncompliance exists in any motor vehicle or item of replacement equipment in the center's possession at the time of notification. In BMW NA's case, this notification would typically be made by the issuance of a recall notification in the form of a Service Information bulletin (SIB) or transmission of a Dealer Communication System (DCS) recall message. Under the National Traffic and Motor Vehicle Safety Act of 1966, as amended, if a recall campaign is announced by BMW NA, centers must ensure that all recalls on new vehicles and new items of replacement equipment are completed BEFORE delivery to the consumer. This means that centers may not legally deliver new motor vehicles or new items of replacement equipment to consumers with an open recall. The Safety Act also prohibits centers from selling or leasing the motor vehicle or item of replacement equipment, unless and until the open recall has been completed BEFORE delivery. This also pertains to vehicles in the Certified Pre-Owned program, and to items of replacement equipment. Finally, BMW centers should not sell or use parts that have been recalled by BMW NA. Please follow the specific instructions provided by BMW NA on the return or disposition of the parts. SUBJECT Voluntary Emissions Recall Campaign 12E-A03: Replace Emissions Label. Certain vehicles were produced with an incorrect model year label installed under the hood (model year 2013). This label needs to be removed and the correct model year 2012 label installed in its place. Customers will receive notification letters informing them to make a service appointment at their BMW centers to have the correct label installed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Service Action: CIC - Install Navigation Road Map Database 2013. Before delivering affected vehicles to the customer, the Car Information Computer (CIC) road map database 2013 must be installed onto the CIC internal Hard Disc Drive (HDD). Note: The INITIAL enabling code ""FSC CIC map, N. America 2013 INITIAL"" is necessary to start the installation process and to activate the road map database."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Discharged Battery: Energy Diagnosis Must Be Performed. The electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle ""discharged battery"" complaints. A discharged battery can have various causes, most of which do not concern the battery itself. A failed battery is often the symptom and not the cause. A fully serviceable battery fails when an electrical component causes the battery to discharge; the battery becomes internally damaged and must be replaced. For more information, refer to www.batteryuniversity.com/parttwo-42B.htm For this reason, replacing the battery is not usually a permanent repair. The cause of the discharged battery must be analyzed in order to guarantee a proper repair. In order to properly repair the vehicle the first time in the workshop, it is very important that the diagnostic test plans are performed to completion with all results taken into to consideration. The procedure as outlined below contains information that will guide the technician into properly repairing the vehicle and getting paid for a warranty claim. CAUSE Refer to the ""Procedure"" section of this Service Information for details."
NHTSA source summary · Original PDF not reviewed by Recallfolio
Clicking Noise from Front Axle. Clicking noises are heard from the front axle area while maneuvering at low speeds (e.g., parking lot maneuvers). CAUSE Movement between the contact surfaces of the wheel bearing and swivel bearing (knuckle)
NHTSA source summary · Original PDF not reviewed by Recallfolio
Service Action: Replace the Left and Right Fuel Level Sensor. After refueling, the fuel gauge will display an incorrect fuel level. When this occurs, the fuel gauge shows the fuel level as 3/4 full. CAUSE Due to a high proportion of ethanol in the fuel, the internal mechanisms of the fuel level sensors may swell. This may inhibit the movement of one or both of the fuel level sensors.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"N63 and N74 Engine: ISTA/D 2.33 Diagnostic Error in the Low-pressure Fuel Supply Sensor Value. INFORMATION When diagnosing the low-pressure fuel supply sensor with one of the following test plans and ISTA/D 2.33, an error will be encountered in the display. The value of the low-pressure fuel supply sensor will read 0 bar at all times. * B1214_DI6KNDR * D18KHDR * AT1214_DIKNDR * AT1214_DIKHDR Do not replace the low-pressure fuel supply sensor. The operating pressure of the low-pressure fuel supply sensor can found in ""DME Diagnostic Query"" using the following procedure: 1. Exit the test plan and return to the control unit tree. http://www.bmwtis.net/tiscode/cgi-bin/omcgi.exe?sie_path=/tsb/bulletins/htm_store/14907...11/7/2012 Page 2 of 2 2. Select ""DME"" in the control unit tree. 3. Select "" Call Up ECU Functions."" 4. Select ""Diagnostic Query."" 5. Select ""Fuel Pressure (Low Pressure)."" 6. Select ""Query Status."" The engine must be running to verify operation of the pressure sensor. The software error will be corrected in ISTA/D 2.34, scheduled for release in December 2012. "
NHTSA source summary · Original PDF not reviewed by Recallfolio
Service Action: Program Control Units (OBD). A software update is available for the DDE (Digital Diesel Electronics) for monitoring Exhaust Gas Recirculation (EGR) and Selective Catalyst Reduction (SCR).
NHTSA source summary · Original PDF not reviewed by Recallfolio
BMW: DUE TO DAMAGED SEAL RING, DURING ASSEMBLY, ENGINE OIL IS LEAKING FROM ENGINE OIL PUMP VOLUME CONTROL VALVE GASKET SEAL RING. MODELS E70, E71, F01, F02, F04, F07, F10, F12, F13. NO MODEL YEARS LISTED. *PE