The manufacturer’s record · Page 2 of 3
Original record summaries, dates and identifiers for this model-year. Records 101–200 of 271, ordered newest first. Dated records on this page: May 1, 2014–Jun 1, 2016.
Back to 2013 BMW X5 problems & recallsThis archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
NHTSA communication ID: 10151375
NHTSA source summary · Original PDF not reviewed by Recallfolio
HeadUp Display does not Show Full Street Names. INFORMATION Design of the HUD has limited display area. (It can only show a certain number of text characters). NOTE: Parts replacement or programming the vehicle will not recitify the situation!
Source components: EQUIPMENT · EQUIPMENT:ELECTRICAL.
Source record 10151375 at NHTSANHTSA communication ID: 10151373
NHTSA source summary · Original PDF not reviewed by Recallfolio
"BMW Maintenance Program: 12-Volt Battery Replacement Measure. INFORMATION This bulletin outlines a customer satisfaction measure that has been designed exclusively for the BMW vehicles listed above. It involves the replacement of the 12-volt battery as a preventive maintenance measure. This 12-volt battery replacement measure is: Effective for repairs dated on or after January 1, 2015. Applicable to vehicles that are still covered by the BMW Maintenance Program. This program is valid for 4 years or 50,000 miles, whichever occurs first. The calculation is based on the current date of repair. It is ""applicable"" when the 12volt battery was not replaced within the last 12 months. You can then perform the battery replacement as outlined below. Please check the warranty claim history for the specific vehicle in the DCSnet Warranty Vehicle Inquiry to confirm the battery was not already replaced within the previous 12 months."
Source components: ELECTRICAL SYSTEM:12V/24V/48V BATTERY.
Source record 10151373 at NHTSANHTSA communication ID: 10151335
NHTSA source summary · Original PDF not reviewed by Recallfolio
Bluetooth Connection Failures. There are various connectivity failures with the following devices: Apple iPhones Samsung S6 and the S6 Edge. Connectivity failure examples are: Call disconnection - Call is transferred back to the handset. In some instances the call is then transferred back to the vehicle. Contact List incomplete General connection failures Apple iOS software (issue started with iOS 8.3 continues with iOS 9.x and its variants) Samsung S6 and S6 Edge device firmware.
Source components: EQUIPMENT · EQUIPMENT:ELECTRICAL.
Source record 10151335 at NHTSANHTSA communication ID: 10151303
NHTSA source summary · Original PDF not reviewed by Recallfolio
"N63, N63TU and N63R Engines: Upper Oil Pan Removal and Installation Repair Instructions This Service Information bulletin supersedes SI B11 17 15 dated August 2015.. INFORMATION When removing and/or installing the engine upper oil pan assembly, the oil pan can sustain damage if this operation is not performed correctly. Before loosening or tightening the engine upper oil pan refer to the newly released Repair Instruction 11 13 010 ""Removing and installing/replacing upper oil sump"" in ISTA/D 3.55.11 or higher for the proper procedures. IMPORTANT: The new repair instructions will state one of the following before reinstalling the upper engine oil pan. ""All threads must be cleaned with screw tap"" Or ""Clean all threads with screw tap. Order number 81 43 0 402 559"" Or ""Clean all threads with a thread cutter"". The current repair instruction terminology will be modified to include this information."
Source components: ENGINE · EQUIPMENT.
Source record 10151303 at NHTSANHTSA communication ID: 10151302
NHTSA source summary · Original PDF not reviewed by Recallfolio
N63, N63TU, S63 and S63TU Engines: Oil Leak from the Rear of the Engine and Transmission Bell Housing. Customer complains that engine oil is leaking from the center of the vehicle. When verified, the engine oil residue can be seen leaking from between the engine and the transmission bell housing.
Source components: POWER TRAIN · POWER TRAIN:CLUTCH ASSEMBLY:BELL HOUSING.
Source record 10151302 at NHTSANHTSA communication ID: 10151301
NHTSA source summary · Original PDF not reviewed by Recallfolio
N63 and S63 Engine: Valve Seal Replacement This Service Information bulletin and attachment supersedes SI B11 08 15 dated March 2016. Refer to the following applicable SIBs before replacing the valve seals. SI B11 07 11 - Turbocharger Failure: Oil Supply and Return Line Blockage and Proper Repairs SI B11 07 12 - N63 Engine: Oil Consumption and/or Rough Running Complaints SI B11 01 13 - N63 Engine: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity SI B11 03 13 - Engine Oil Consumption (all models) If the valve seals are leaking, one of the following will help determine if the seals should be replaced. Smoke from the tailpipe when starting or aggressively accelerating and decelerating the engine Excessive engine oil consumption Spark plugs fouled with engine oil
Source components: ENGINE.
Source record 10151301 at NHTSANHTSA communication ID: 10151262
NHTSA source summary · Original PDF not reviewed by Recallfolio
Squeaking Brakes on the Front Axle for the E70 and E71. A squeaking noise can be heard from the front axle during braking. Front axle brake system
Source components: SERVICE BRAKES.
Source record 10151262 at NHTSANHTSA communication ID: 10151255
NHTSA source summary · Original PDF not reviewed by Recallfolio
ISTA/P Cannot Program an E-Series N55 Replacement DME. ISTA/P fails when attempting to program a replacement DME (MEVD172) on BN2000 E-Series vehicles with the Continental HPP. Part number: 12 14 8 618 483. DME logistic error between the replacement hardware and basic software prevents correct programming with ISTA/P.
Source components: ELECTRICAL SYSTEM · EQUIPMENT.
Source record 10151255 at NHTSANHTSA communication ID: 10151248
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Service Information bulletin and attachment supersedes SI B11 08 15 dated November 2015. SUBJECT N63 and S63 Engine: Valve Seal Replacement. Refer to the following applicable SIBs before replacing the valve seals. SI B11 07 11 - Turbocharger Failure: Oil Supply and Return Line Blockage and Proper Repairs SI B11 07 12 - N63 Engine: Oil Consumption and/or Rough Running Complaints SI B11 01 13 - N63 Engine: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity SI B11 03 13 - Engine Oil Consumption (all models) If the valve seals are leaking, one of the following will help determine if the seals should be replaced. Smoke from the tailpipe when starting or aggressively accelerating and decelerating the engine Excessive engine oil consumption Spark plugs fouled with engine oil
Source components: ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER · EQUIPMENT · FUEL SYSTEM, GASOLINE.
Source record 10151248 at NHTSANHTSA communication ID: 10151246
NHTSA source summary · Original PDF not reviewed by Recallfolio
"The crankcase ventilation connection line may deteriorate prematurely causing any of the following: vacuum leak various fault codes related to mixture control stored in the DME customer complaints about rough idle speed Check Engine Light illumination. AFFECTED VEHICLES This Service Action involves certain E70 X5 M and E71 X6 M vehicles produced from March 1, 2011 to July 23, 2014. Vehicles which require this Service Action to be completed will show it as ""Open"" when checked either in the ""Service Menu"" of DCSnet (Dealer Communication System) or with the Key Reader."
Source components: ENGINE AND ENGINE COOLING.
Source record 10151246 at NHTSANHTSA communication ID: 10076475
NHTSA source summary · Original PDF not reviewed by Recallfolio
Service Action: S63 Engine Replace Crankcase Vent Connecting Line The crankcase ventilation connection line may deteriorate prematurely causing any of the following: vacuum leak various fault codes related to mixture control stored in the DME customer complaints about rough idle speed Check Engine Light illumination.
Source components: ENGINE.
Source record 10076475 at NHTSANHTSA communication ID: 10151165
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Service Information bulletin and attachment supersedes SI B11 08 15 dated November 2015. SUBJECT N63 and S63 Engine: Valve Seal Replacement. Refer to the following applicable SIBs before replacing the valve seals. B11 07 11 - Turbocharger Failure: Oil Supply and Return Line Blockage and Proper Repairs B11 07 12 - N63 Engine: Oil Consumption and/or Rough Running Complaints B11 01 13 - N63 Engine: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity B11 03 13 - Engine Oil Consumption (all models) If the valve seals are leaking, one of the following will help determine if the seals should be replaced. Smoke from the tailpipe when starting or aggressively accelerating and decelerating the engine Excessive engine oil consumption Spark plugs fouled with engine oil
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE · EQUIPMENT.
Source record 10151165 at NHTSANHTSA communication ID: 10151119
NHTSA source summary · Original PDF not reviewed by Recallfolio
SI B84 03 14 February 2016 Communication Systems Technical Service This Service Information bulletin supersedes SI B84 03 14 dated October 2014. SUBJECT Bluetooth Connection Failures. There are various connectivity failures with the following devices: Apple iPhones Samsung S6 and the S6 Edge. Connectivity failure examples are: Call disconnection - Call is transferred back to the handset. In some instances the call is then transferred back to the vehicle. Contact List incomplete General connection failures CAUSE Apple iOS software (issue started with iOS 8.3 continues with iOS 9.x and its variants) Samsung S6 and S6 Edge device firmware CORRECTOPM None available at this time. We are currently working with the device manufacturer on a solution.
Source components: ELECTRICAL SYSTEM · EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10151119 at NHTSANHTSA communication ID: 10151115
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUBJECT Audio System Speaker Testing. For audio system speaker testing there is a NED (Non Electrical Diagnosis) Test Plan available. CAUSE We previously recommended use of the Audio Test CD (ATC) from BMW. This CD has been discontinued.
Source components: ELECTRICAL SYSTEM · EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10151115 at NHTSANHTSA communication ID: 10151080
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain air conditioning condensers must be replaced. Premature condenser failure due to corrosion. Replace the condenser if the vehicle contains the affected part number (9255983) AND the production date of the part falls on or before 11/11/13.
Source components: EQUIPMENT:APPLIANCE:AIR CONDITIONER.
Source record 10151080 at NHTSANHTSA communication ID: 10151071
NHTSA source summary · Original PDF not reviewed by Recallfolio
"This Service Information bulletin and attachment supersedes SI B11 16 14 dated May 2015. designates changes to this revision SUBJECT N63 Engine: Check the Timing Chain. INFORMATION This bulletin outlines the procedure for checking the engine timing chains for wear, and should be completed in conjunction with SI B11 06 14, ""N63 Customer Care Package."" The N63CCP and N63 Engine Check the Timing Chain are NOT mandatory Technical Campaigns or Recalls. They should be completed only based on parts availability, workshop capacity, and the customer's schedule. Performing the test plans identified in the procedure below will detect wear at an early stage and, if necessary, provide a repair solution. To avoid future valvetrain wear, the vehicle must be reprogrammed and a shorter oil service interval must be retrofitted via ISTA/P. Finally, drain and replace the engine's oil and filter. After completing all necessary repairs included in the N63 Customer Care Package and the Timing Chain Check, the vehicle must be test driven for up to 30 minutes to ensure that the repairs were performed to the highest standard."
Source components: ENGINE · ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:BELTS AND ASSOCIATED PULLEYS · EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10151071 at NHTSANHTSA communication ID: 10151068
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Service Information bulletin supersedes SI B07 03 14 dated October 2015. Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Fault codes stored in vehicles being serviced are not being diagnosed, leading to repeat repair visits (source- Analysis of FASTA data and repeat repair visit reports). INFORMATION Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) to find their root cause during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
Source components: ELECTRICAL SYSTEM · ENGINE · EQUIPMENT · STEERING.
Source record 10151068 at NHTSANHTSA communication ID: 10151023
NHTSA source summary · Original PDF not reviewed by Recallfolio
Whistling Noise Coming from the Center Vent - A/C is Off . A very high pitched whistling or beeping noise is heard coming from the center vents. The flow of refrigerant through the expansion valve at certain temperature differentials.
Source components: EQUIPMENT:APPLIANCE:AIR CONDITIONER.
Source record 10151023 at NHTSANHTSA communication ID: 10151015
NHTSA source summary · Original PDF not reviewed by Recallfolio
SI B61 30 14. January 2016. General Electrical Systems Technical Service This Service Information bulletin supersedes SI B61 30 14 dated December 2015. designates changes to this revision SUBJECT BMW Maintenance Program: 12-Volt Battery Replacement Measure . INFORMATION This bulletin outlines a customer satisfaction measure that has been designed exclusively for the BMW vehicles listed above. It involves the replacement of the 12-volt battery as a preventive maintenance measure. This 12-volt battery replacement measure is: Effective for repairs dated on or after January 1, 2015. Applicable to vehicles that are still covered by the BMW Maintenance Program. This program is valid for 4 years or 50,000 miles, whichever occurs first. The calculation is based on the current date of repair. It is "applicable" when the 12volt battery was not replaced within the last 12 months. You can then perform the battery replacement as outlined below. Please check the warranty claim history for the specific vehicle in the DCSnet Warranty Vehicle Inquiry to confirm the battery was not already replaced within the previous 12 months.
Source components: ELECTRICAL SYSTEM.
Source record 10151015 at NHTSANHTSA communication ID: 10150904
NHTSA source summary · Original PDF not reviewed by Recallfolio
The high-pressure injectors may fail, resulting in an engine malfunction warning and reduced engine output.
Source components: ENGINE · FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM:INJECTORS.
Source record 10150904 at NHTSANHTSA communication ID: 10147882
NHTSA source summary · Original PDF not reviewed by Recallfolio
"?SI B61 30 14December 2015 General Electrical SystemsTechnical Service This Service Information bulletin supersedes SI B61 30 14 dated July 2015. designates changes to this revision SUBJECT BMW Maintenance Program: 12-Volt Battery Replacement Measure. INFORMATION This bulletin outlines a customer satisfaction measure that has been designed exclusively for the BMW vehicles listed above. It involves the replacement of the 12-volt battery as a preventive maintenance measure. This 12-volt battery replacement measure is: Effective for repairs dated on or after January 1, 2015. Applicable to vehicles that are still covered by the BMW Maintenance Program. This program is valid for 4 years or 50,000 miles, whichever occurs first. The calculation is based on the current date of repair. It is ""applicable"" when the 12volt battery was not replaced within the last 12 months. You can then perform the battery replacement as outlined below. Please check the warranty claim history for the specific vehicle in the DCSnet Warranty Vehicle Inquiry to confirm the battery was not already replaced within the previous 12 months. "
Source components: ELECTRICAL SYSTEM.
Source record 10147882 at NHTSANHTSA communication ID: 10147862
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Engine Idle Speed Fluctuates Intermittently, when Shifting into Gear. While stationary, the engine idle speed could fluctuate (once or a few times) after engaging either ""Drive"" or ""Reverse gear. It is possible that the engine could also stall. This situation is intermittent, difficult to reproduce, and would not cause a fault to be stored. However, it is more likely to occur right after restarting a hot engine, A/C on, steering turned, and at ambient temperatures above 70° F. CAUSE DME software error (idle speed controller set point)."
Source components: ENGINE.
Source record 10147862 at NHTSANHTSA communication ID: 10147808
NHTSA source summary · Original PDF not reviewed by Recallfolio
N63 Engine: Valve Seal Replacement. Refer to the following applicable SIBs before replacing the valve seals. ? B11 07 11 - Turbocharger Failure: Oil Supply and Return Line Blockage and Proper Repairs ? B11 07 12 - N63 Engine: Oil Consumption and/or Rough Running Complaints ? B11 01 13 - N63 Engine: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity ? B11 03 13 - Engine Oil Consumption (all models) If the valve seals are leaking, one of the following will help determine if the seals should be replaced. ? Smoke from the tailpipe when starting or aggressively accelerating and decelerating the engine ? Excessive engine oil consumption ? Spark plugs fouled with engine oil
Source components: ENGINE.
Source record 10147808 at NHTSANHTSA communication ID: 10147763
NHTSA source summary · Original PDF not reviewed by Recallfolio
Delivery Stop: Program Electronic Control Unit. A Delivery Stop has been issued on F15 PHEV vehicles produced from July 6, 2015 to October 21, 2015. These vehicles require programming of the Electric Machine Electronics (EME) Control Unit. The software will be available with ISTA/P 3.57.1 as of November 6, 2015. This bulletin will be updated with repair instructions and warranty information when it becomes available. Please contact your field representatives if you have any questions.
Source components: ELECTRICAL SYSTEM · ENGINE.
Source record 10147763 at NHTSANHTSA communication ID: 10147761
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Engine Idle Speed Fluctuates Intermittently, when Shifting into Gear. While stationary, the engine idle speed could fluctuate (once or a few times) after engaging either ""Drive"" or ""Reverse gear. It is possible that the engine could also stall. This situation is intermittent, difficult to reproduce, and would not cause a fault to be stored. However, it is more likely to occur right after restarting a hot engine, A/C on, steering turned, and at ambient temperatures above 70° F. CAUSE DME software error (idle speed controller set point)."
Source components: ELECTRICAL SYSTEM · ENGINE.
Source record 10147761 at NHTSANHTSA communication ID: 10147759
NHTSA source summary · Original PDF not reviewed by Recallfolio
?N63 Engine: Valve Seal Replacement. Refer to the following applicable SIBs before replacing the valve seals. B11 07 11 - Turbocharger Failure: Oil Supply and Return Line Blockage and Proper Repairs B11 07 12 - N63 Engine: Oil Consumption and/or Rough Running Complaints B11 01 13 - N63 Engine: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity B11 03 13 - Engine Oil Consumption (all models) If the valve seals are leaking, one of the following will help determine if the seals should be replaced. Smoke from the tailpipe when starting or aggressively accelerating and decelerating the engine Excessive engine oil consumption Spark plugs fouled with engine oil.
Source components: ENGINE.
Source record 10147759 at NHTSANHTSA communication ID: 10147758
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Service Information bulletin supersedes SI B07 03 14 dated May 2015. designates changes to this revision SUBJECT Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Fault codes stored in vehicles being serviced are not being diagnosed, leading to repeat repair visits (source- Analysis of FASTA data and repeat repair visit reports). INFORMATION Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) to find their root cause during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
Source components: EQUIPMENT.
Source record 10147758 at NHTSANHTSA communication ID: 10147241
NHTSA source summary · Original PDF not reviewed by Recallfolio
Shudder from the Driveline on Vehicles with xDrive. There is a shudder or vibration from the driveline when taking off from a stop, or when accelerating at highway speeds. CAUSE Possible multiple root causes related to the engine, wheels & tires, suspension components or internal wear on the clutch plates of the xDrive transfer case.
Source components: POWER TRAIN:DRIVELINE · WHEELS.
Source record 10147241 at NHTSANHTSA communication ID: 10151404
NHTSA source summary · Original PDF not reviewed by Recallfolio
Vibration or Shudder from Driveline when Accelerating from a Stop. Chassis stabilization warning is displayed. Vehicle may exhibit a shudder or vibration when taking off from a stop. One or more of the following fault codes may be stored: LMV ? 440101 - Transfer box (VTG): End of transmission service life reached ? 440105 - Transfer box (VTG ) Calibration Faulty ? 440115 - Transfer box (VTG): Calibration angle deviation outside tolerance? 44011B - Set torque outside of the torque characteristic curve EGS ? 420611 - DSC interface (wheel speed): non-permitted deviation of wheel speed (actual speed of wheel RL/FL/RR/FR, 0x254) from output speed and turbine speed DSC ? 48097D - Transfer box: Fault, clutch position known, only rear-wheel drive These symptoms or faults would be stored on a vehicle with low mileage (< 12,500 miles). CAUSE A front or rear differential with the incorrect gear ratio was installed in the car. The front and rear differentials need to be geared exactly the same for the xDrive to function properly.
Source components: POWER TRAIN.
Source record 10151404 at NHTSANHTSA communication ID: 10151400
NHTSA source summary · Original PDF not reviewed by Recallfolio
"N63 and S63 Engine: Upper Oil Pan Removal and Installation Procedures. INFORMATION When removing and/or installing the N63 or S63 engine ""upper"" oil pan assembly, the oil pan can sustain damage if this operation is not performed correctly. Before loosening or tightening the upper oil pan bolts as per Repair Instruction 11 13 010 ""Removing and installing /replacing upper oil sump (N63),"" the steps outlined in the attachment of this bulletin must be followed. Refer to attached document and the instruction section that applies to the procedure being carried out. The ISTA/D repair instructions are currently being revised."
Source components: ENGINE · EQUIPMENT.
Source record 10151400 at NHTSANHTSA communication ID: 10151396
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Front Propeller (Drive) Shaft: Limited Warranty Extension to 10 Years/120,000 Miles. INFORMATION For the above-referenced vehicles, BMW of North America, LLC (""BMW NA"") is extending the limited warranty for the: ? Front propeller (drive) shaft to 10 years/120,000 miles as determined by the vehicle's original in-service date This bulletin is notice of a ""limited warranty extension."" This is NOT a notice of a Recall or Service Action. There is no immediate repair required unless the BMW vehicle is currently experiencing problem with this component. Customer Notification Letter - VIN and Component-specific Warranty Extension Even though this is NOT a Recall, BMW NA will be sending VIN-specific ""customer notification letters,"" in a ""phased"" release, beginning on or after August 24, 2015. A sample letter is attached. ELIGIBLE BMW VEHICLES To assist you in identifying the eligible vehicles, the DCSnet Warranty Vehicle Inquiry has been updated with the ""Vehicle Comment"" shown below: BMW NA has extended the limited warranty for the front propeller (drive) shaft on this vehicle to 10 years/120,000 miles as determined from the original in-service date, subject to the applicable vehicle and coverage eligibility requirements, exclusions and limitations that apply to the BMW New Vehicle Limited Warranty for Passenger Cars and Light Trucks. Please see SI B01 15 15. Note: Always check the DCSnet Warranty Vehicle Inquiry ""Vehicle Comments"" and the ""Repair History (Claims)"" sections first, before performing any repairs. "
Source components: POWER TRAIN:DRIVELINE:DRIVESHAFT.
Source record 10151396 at NHTSANHTSA communication ID: 10059089
NHTSA source summary · Original PDF not reviewed by Recallfolio
BMW - BRAKE BOOSTER VACUUM MIGHT REDUCE IF TEMPERATURE GETS BELOW 14 DEGREES *MA
Source components: SERVICE BRAKES.
Source record 10059089 at NHTSANHTSA communication ID: 10058973
NHTSA source summary · Original PDF not reviewed by Recallfolio
LIMITED WARRANTY HAS BEEN EXTENDED TO CERTAIN VEHICLES FOR 10 YEARS/120,000 MILES. WHICH EVER COMES FIRST. *MA
Source components: EQUIPMENT.
Source record 10058973 at NHTSANHTSA communication ID: 10147206
NHTSA source summary · Original PDF not reviewed by Recallfolio
CAS Module Fails Programming with CoAPI Error 2082. During vehicle programming, the CAS (Car Access System) module fails to program with CoAPI error 2082 displayed. Refer to the attachment, which lists the affected CAS serial numbers. The following part numbers are affected: 61 35 9 287 534 61 35 9 226 238 61 35 9 227 053 61 35 9 287 535
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:SOFTWARE.
Source record 10147206 at NHTSANHTSA communication ID: 10147192
NHTSA source summary · Original PDF not reviewed by Recallfolio
"?SI B13 02 15July 2015 Fuel SystemsTechnical Service This Service Information bulletin supersedes SI B13 02 15 dated May 2015. designates changes to this revision SUBJECT Service Action: N63 Replace High-Pressure Fuel Pumps. The high-pressure pump may fail, resulting in an engine malfunction warning and reduced engine output. This Service Action involves F01, F02, F04, F07, F10, F12, F13, E70, E71, and E72 vehicles with the N63 engine produced from January 1, 2011 to December 1, 2011. Vehicles which require this Service Action to be completed will show it as ""Open"" when checked either in the ""Service Menu"" of DCSnet (Dealer Communication System) or with the Key Reader. CAUSE The high-pressure pump quantity control valve may fail."
Source components: FUEL SYSTEM, GASOLINE:DELIVERY:FUEL PUMP.
Source record 10147192 at NHTSANHTSA communication ID: 10147724
NHTSA source summary · Original PDF not reviewed by Recallfolio
iDrive Controller Trim Peeling. The chrome ring on the iDrive controller is peeling. Poor chrome material adhesion.
Source components: EQUIPMENT.
Source record 10147724 at NHTSANHTSA communication ID: 10147722
NHTSA source summary · Original PDF not reviewed by Recallfolio
"BMW Maintenance Program: 12-Volt Battery Replacement Measure. INFORMATION This bulletin outlines a customer satisfaction measure that has been designed exclusively for the BMW vehicles listed above. It involves the replacement of the 12-volt battery as a preventive maintenance measure. This 12-volt battery replacement measure is: ? Effective for repairs dated on or after January 1, 2015. ? Applicable to vehicles that are still covered by the BMW Maintenance Program. This program is valid for 4 years or 50,000 miles, whichever occurs first. ? The calculation is based on the current date of repair. It is ""applicable"" when the 12-volt battery was not replaced within the last 12 months. You can then perform the battery replacement as outlined below. Please check the warranty claim history for the specific vehicle in the DCSnet Warranty Vehicle Inquiry to confirm the battery was not already replaced within the previous 12 months."
Source components: ELECTRICAL SYSTEM:12V/24V/48V BATTERY.
Source record 10147722 at NHTSANHTSA communication ID: 10147712
NHTSA source summary · Original PDF not reviewed by Recallfolio
Service Action: Reprogram the DDE. The DDE calibration for readiness monitoring may be incorrect.
Source components: FUEL SYSTEM, GASOLINE.
Source record 10147712 at NHTSANHTSA communication ID: 10059006
NHTSA source summary · Original PDF not reviewed by Recallfolio
INCORRECT DDE CALIBRATION FOR READINES MONITORING. *MA
Source components: ENGINE AND ENGINE COOLING:ENGINE:DIESEL.
Source record 10059006 at NHTSANHTSA communication ID: 10147136
NHTSA source summary · Original PDF not reviewed by Recallfolio
Valve Stem Replacement with Wheel Electronics. INFORMATION The valve stems are single-use only, and must be replaced every time the wheel electronics are replaced. If you loosen the nut (1), you must replace the valve stem. Failure to replace the valve stem will lead to a pressure leak. The proper repair procedure can be found in REP 3611533. Not applicable. [ Copyright (c)2015 BMW of North America, Inc. ] Page 1 of 3 Page 1 of 1 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015 Page 1 of 3 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015
Source components: TIRES:VALVE · WHEELS.
Source record 10147136 at NHTSANHTSA communication ID: 10147132
NHTSA source summary · Original PDF not reviewed by Recallfolio
Service Action: Replace Oxygen Sensor. The oxygen sensor deteriorates prematurely.
Source components: ENGINE.
Source record 10147132 at NHTSANHTSA communication ID: 10147131
NHTSA source summary · Original PDF not reviewed by Recallfolio
Service Action: N63 Replace High-Pressure Fuel Pumps. The high-pressure pump may fail, resulting in an engine malfunction warning and reduced engine output.
Source components: FUEL SYSTEM, GASOLINE.
Source record 10147131 at NHTSANHTSA communication ID: 10147127
NHTSA source summary · Original PDF not reviewed by Recallfolio
"This bulletin outlines the procedure for checking the engine timing chains for wear, and should be completed in conjunction with SI B11 06 14, ""N63 Customer Care Package."" The N63CCP and N63 Engine Check the Timing Chain are NOT mandatory Technical Campaigns or Recalls. They should be completed only based on parts availability, workshop capacity, and the customer's schedule. Performing the test plans identified in the procedure below will detect wear at an early stage and, if necessary, provide a repair solution. To avoid future valvetrain wear, the vehicle must be reprogrammed and a shorter oil service interval must be retrofitted via ISTA/P. Finally, drain and replace the engine's oil and filter. After completing all necessary repairs included in the N63 Customer Care Package and the Timing Chain Check, the vehicle must be test driven for up to 30 minutes to ensure that the repairs were performed to the highest standard."
Source components: ENGINE.
Source record 10147127 at NHTSANHTSA communication ID: 10147125
NHTSA source summary · Original PDF not reviewed by Recallfolio
N63 Engine: Valve Seal Replacement. Refer to the following applicable SIBs before replacing the valve seals. ? B11 07 11 - Turbocharger Failure: Oil Supply and Return Line Blockage and Proper Repairs ? B11 07 12 - N63 Engine: Oil Consumption and/or Rough Running Complaints ? B11 01 13 - N63 Engine: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity ? B11 03 13 - Engine Oil Consumption (all models) If the valve seals are leaking, one of the following will help determine if the seals should be replaced. ? Smoke from the tailpipe when starting or aggressively accelerating and decelerating the engine ? Excessive engine oil consumption ? Spark plugs fouled with engine oil
Source components: ENGINE.
Source record 10147125 at NHTSANHTSA communication ID: 10147123
NHTSA source summary · Original PDF not reviewed by Recallfolio
Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Analysis of FASTA data and repeat repair visit reports indicates that there are many fault codes that are stored in the above vehicles, but they are not diagnosed to identify their root cause. Fault codes that are not diagnosed to find their root cause can lead to a repeat repair visit to the workshop by the customer. Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
Source components: ELECTRICAL SYSTEM.
Source record 10147123 at NHTSANHTSA communication ID: 10057338
NHTSA source summary · Original PDF not reviewed by Recallfolio
BMW: ON CERTAIN VEHICLES, ENGINE TIMING CHAIN SHOULD BE CHECKED FOR EARLY STAGES OF WEAR, AND A REPAIR SOLUTION SHOULD BE PROVIDED. *PE UPDATED 9/25/15. *PE UPDATED 10/6/15. *PE
Source components: ENGINE.
Source record 10057338 at NHTSANHTSA communication ID: 10193495
NHTSA source summary · Original PDF not reviewed by Recallfolio
The customer complains of rattling noises from the rear window when driving on rough roads.
Source components: VISIBILITY.
Source record 10193495 at NHTSANHTSA communication ID: 10152309
NHTSA source summary · Original PDF not reviewed by Recallfolio
Service Action: Program Control Units (SCR). The Selective Catalyst Reduction (SCR) control module can make an error when calculating the DEF line pressure. This could cause the Service Engine Soon light (MIL) to come on with a pressure plausibility fault stored in the SCR module.
Source components: ELECTRICAL SYSTEM.
Source record 10152309 at NHTSANHTSA communication ID: 10152308
NHTSA source summary · Original PDF not reviewed by Recallfolio
Service Action: Replace Oxygen Sensor. The oxygen sensor deteriorates prematurely.
Source components: ENGINE AND ENGINE COOLING.
Source record 10152308 at NHTSANHTSA communication ID: 10152301
NHTSA source summary · Original PDF not reviewed by Recallfolio
"This bulletin outlines the Customer Care Package program that has been designed exclusively for BMW vehicles with the N63 engine. Vehicles with the N63 high performance engine are engineered with EfficientDynamics that provides fuel economy without compromising on its ""class leading"" power and performance. To ensure these engines keep delivering the ultimate performance, we have designed this Care Package that includes a 6 point check, and if necessary, the replacement of one or more of the following powertrain components: ? Hot-Film Air Mass Sensors ? PIEZO High Pressure Fuel Injectors ? Engine Vacuum Pump ? Fuel System Low Pressure Sensor/Feed Line ? Fresh Air Intake Turbo Seals ? Crankcase Ventilation Lines (Hoses) Note: Due to ongoing quality control monitoring, testing of the Bosch fuel system low-pressure sensor showed that replacement of the fuel system low-pressure sensor with Index 1 is no longer required in this customer care package. Refer to the attached procedure for the applicable replacement instructions regarding the fuel system low-pressure sensor. This engine care package also includes a multi-point inspection of the vehicle, including tire pressures, fluid levels, safety and convenience features. The N63CCP is NOT a mandatory Technical Campaign or Recall (per the authorities). It should only be completed based on parts availability, workshop capacity, and the customer's schedule. Complete all other applicable open Campaigns per the DCS Warranty inquiry and the Key Reader. Perform all recommended, due or qualifying ""time-based"" maintenance service task items as directed by the Key Reader/ISPA Light application. When eligible, also perform the procedure described in SI B61 30 14: 12-Volt Battery Replacement together with performing the N63 Customer Care Package. After completing all the necessary repairs, the vehicle needs to be road tested for 30 minutes to assure the highest standard of performed repairs (Please see ""Warranty Inf
Source components: EQUIPMENT.
Source record 10152301 at NHTSANHTSA communication ID: 10058483
NHTSA source summary · Original PDF not reviewed by Recallfolio
BMW: PROCEDURAL INFORMATION ON THE INSTALLATION OF FUEL SYSTEM LOW PRESSURE SENSOR AND NOT CORRECTLY INSTALLED WILL LEAD TO FAILURE OF LOW PRESSURE SENSOR AND METAL SUPPLY LINE. MODEL 2008-14. *PE
Source components: FUEL SYSTEM, OTHER.
Source record 10058483 at NHTSANHTSA communication ID: 10058442
NHTSA source summary · Original PDF not reviewed by Recallfolio
BMW: ENGINE (SPARK) KNOCKING IS HEARD IF AFTER LONG IDLE PHASES AND THEN FULL THROTTLE ACCELERATIONS OCCURS AFTER DRIVING CAN CAUSE ENGINE INTERNAL DAMAGE, IN SOME VEHICLES. MODEL 2013-14 F15 (X5). *PE
Source components: ENGINE.
Source record 10058442 at NHTSANHTSA communication ID: 10147669
NHTSA source summary · Original PDF not reviewed by Recallfolio
Driveshaft Technical Service. This Service Information bulletin supersedes SI B26 01 14 dated August 2014. PERFORM THE PROCEDURE OUTLINED IN THIS SERVICE INFORMATION ON ALL AFFECTED VEHICLES BEFORE CUSTOMER DELIVERY OR THE NEXT TIME THEY ARE IN THE SHOP FOR MAINTENANCE OR REPAIRS. designates changes to this revision SUBJECT Service Action: Inspect Front Driveshaft. The universal joints in the front driveshaft may wear out prematurely.
Source components: POWER TRAIN:DRIVELINE:DRIVESHAFT.
Source record 10147669 at NHTSANHTSA communication ID: 10147660
NHTSA source summary · Original PDF not reviewed by Recallfolio
"SI B12 10 15 Engine Electrical Systems March 2015 Technical Service This Service Information bulletin supersedes SI B12 10 15 dated January 2015. designates changes to this revision SUBJECT N63: CBS Oil Service Conversion in ISTA/P. The CBS oil service conversion performed for the N63 Customer Car Package and timing chain check (SI B11 16 14) did not work correctly with ISTA/P 3.54.x or 3.55.0. It did not change the interval to the desired 12 months/10,000 miles for the vehicles listed above in the specified production ranges. The ""Conversion, oil service 12 months/15,000 km/10,000 miles"" is working properly for all other N63 vehicles produced after these dates. Incorrect coding data in the affected ISTA/P versions"
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT:ELECTRICAL.
Source record 10147660 at NHTSANHTSA communication ID: 10147656
NHTSA source summary · Original PDF not reviewed by Recallfolio
"This bulletin outlines the procedure for checking the engine timing chains for wear, and should be completed in conjunction with SI B11 06 14, ""N63 Customer Care Package."" The N63CCP and N63 Engine Check the Timing Chain are NOT mandatory Technical Campaigns or Recalls. They should be completed only based on parts availability, workshop capacity, and the customer's schedule. Performing the test plans identified in the procedure below will detect wear at an early stage and, if necessary, provide a repair solution. To avoid future valvetrain wear, the vehicle must be reprogrammed and a shorter oil service interval must be retrofitted via ISTA/P. Finally, drain and replace the engine's oil and filter. After completing all necessary repairs included in the N63 Customer Care Package and the Timing Chain Check, the vehicle must be test driven for up to 30 minutes to ensure that the repairs were performed to the highest standard. AFFECTED VEHICLES This Service Action applies to E70, E71, E72, F01, F02, F04, F07, F10, F12, and F13 vehicles with the N63 engines corresponding to the production dates listed above. First check if a Service Action label with a code number 728 is already attached to the B-pillar. If a code number 728 has already been punched out, the Campaign has already been performed and no further action is necessary. Eligible vehicles will show the following Service Action-related Campaign Code: 00 13 48 02 00 If the vehicle already has a label from a previous Service Action/Recall Campaign, affix the new label next to the old one. Do not affix one label on top of another one, because a number from an underlying label could appear in the punched-out hole of the new label."
Source components: ENGINE.
Source record 10147656 at NHTSANHTSA communication ID: 10147655
NHTSA source summary · Original PDF not reviewed by Recallfolio
"N63: Quality Control Monitoring After CCP. INFORMATION If the vehicle exhibits any of the above drivability issues, perform the ISTA/D N63 Misfire Detection test plan. Please make sure the FASTA data is transmitted. Submit a PuMA case titled ""N63: Drivability after CCP."" Follow the recommendations received."
Source components: ENGINE.
Source record 10147655 at NHTSANHTSA communication ID: 10058494
NHTSA source summary · Original PDF not reviewed by Recallfolio
DOOR OPENS, WHILE DRIVING, TO FIRST STAGE, CAUSING CHECK CONTROL MESSAGE TO BE DISPLAYED *CN
Source components: LATCHES/LOCKS/LINKAGES:DOORS:LATCH · STRUCTURE:BODY:DOOR.
Source record 10058494 at NHTSANHTSA communication ID: 10147085
NHTSA source summary · Original PDF not reviewed by Recallfolio
"SI B61 30 14February 2015 General Electrical SystemsTechnical Service This Service Information bulletin supersedes SI B61 30 14 dated January 2015. designates changes to this revision SUBJECT BMW Maintenance Program: 12-Volt Battery Replacement Measure. INFORMATION This bulletin outlines a customer satisfaction measure that has been designed exclusively for the BMW vehicles listed above. It involves the replacement of the 12-volt battery as a preventive maintenance measure. This 12-volt battery replacement measure is: ? Effective for repairs dated on or after January 1, 2015. ? Applicable to vehicles that are still covered by the BMW Maintenance Program. This program is valid for 4 years or 50,000 miles, whichever occurs first. ? The calculation is based on the current date of repair. It is ""applicable"" when the 12-volt battery was not replaced within the last 12 months. You can then perform the battery replacement as outlined below. Please check the warranty claim history for the specific vehicle in the DCSnet Warranty Vehicle Inquiry to confirm the battery was not already replaced within the previous 12 months."
Source components: ELECTRICAL SYSTEM.
Source record 10147085 at NHTSANHTSA communication ID: 10147068
NHTSA source summary · Original PDF not reviewed by Recallfolio
"This Service Information bulletin and attachment supersedes SI B11 16 14 dated January 2015. designates changes to this revision SUBJECT N63 Engine: Check the Timing Chain. INFORMATION This bulletin outlines the procedure for checking the engine timing chains for wear, and should be completed in conjunction with SI B11 06 14, ""N63 Customer Care Package."" The N63CCP and N63 Engine Check the Timing Chain are NOT mandatory Technical Campaigns or Recalls. They should be completed only based on parts availability, workshop capacity, and the customer's schedule. Performing the test plans identified in the procedure below will detect wear at an early stage and, if necessary, provide a repair solution. To avoid future valvetrain wear, the vehicle must be reprogrammed and a shorter oil service interval must be retrofitted via ISTA/P. Finally, drain and replace the engine's oil and filter. After completing all necessary repairs included in the N63 Customer Care Package and the Timing Chain Check, the vehicle must be test driven for up to 30 minutes to ensure that the repairs were performed to the highest standard."
Source components: ENGINE.
Source record 10147068 at NHTSANHTSA communication ID: 10147067
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Service Information bulletin supersedes SI B07 03 14 dated February 2015. designates changes to this revision SUBJECT Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Analysis of FASTA data and repeat repair visit reports indicates that there are many fault codes that are stored in the above vehicles, but they are not diagnosed to identify their root cause. Fault codes that are not diagnosed to find their root cause can lead to a repeat repair visit to the workshop by the customer. Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
Source components: ELECTRICAL SYSTEM.
Source record 10147067 at NHTSANHTSA communication ID: 10057707
NHTSA source summary · Original PDF not reviewed by Recallfolio
BMW:SOME BMW MODELS MAY OR MAY NOT DISPLAY AIRBAG WARNING LIGHT. *TA
Source components: AIR BAGS:FRONTAL:SENSOR/CONTROL MODULE-INACTIVE · INTERIOR LIGHTING.
Source record 10057707 at NHTSANHTSA communication ID: 10057340
NHTSA source summary · Original PDF not reviewed by Recallfolio
BMW: CALCULATION ERROR BY SCR MODULE SOFTWARE OF DEF LINE PRESSURE CAUSING SERVICE ENGINE SOON LIGHT (MIL) TO ILLUMINATE. *PE
Source components: ELECTRICAL SYSTEM:SOFTWARE · ENGINE AND ENGINE COOLING:ENGINE:DIESEL.
Source record 10057340 at NHTSANHTSA communication ID: 10147624
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Service Information bulletin supersedes SI B65 10 09 dated March 2013. designates changes to this revision SUBJECT CIC head unit: Vehicle Position Is Missing or Incorrect on Navigation Map. The vehicle position is missing or incorrect on the navigation map. The navigation system integrated in the Car Information Computer (CIC) is not calibrated correctly.
Source components: EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM).
Source record 10147624 at NHTSANHTSA communication ID: 10147623
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Service Information bulletin supersedes SI B65 05 09 dated July 2009. designates changes to this revision SUBJECT CIC Headunit: Navigation System Road Map Usage. INFORMATION The Car Information Computer (CIC) began replacing the Car Communication Computer (CCC) on vehicles with option 609 in September of 2008. This change affected the navigation system road map data support process and the warranty spare parts processes for the CIC. For the US market, all vehicles come pre-loaded from the factory with the latest navigation system road map database version that was available at the time of vehicle production. Therefore, no physical copy of the navigation system road map data media DVD set or USB stick is placed in these vehicles at the Vehicle Distribution Center (VDC). NOTE: Additionally, all replacement CIC parts come with a pre-loaded version of the current available navigation system road map database installed. A set of DVD copies of the navigation system road map database, CIC NAVI Road Map North America PREMIUM, is shipped to all BMW centers through the automatic tool shipment program with each release of a navigation system road map database. IMPORTANT: Additional copies or earlier NAV road map database versions cannot be ordered individually! Therefore, please take special care to archive the CIC NAV road map DVD sets! The NAV road map data on the DVD set can also be installed into the Network Attached Storage (NAS). From there, it can then be installed onto the CIC in the vehicle, using the Integrated Service Technical Application for Programming (ISTA/P). For installation of the navigation system road map data media DVD set onto the Network Attached Storage (NAS), please contact your ISPI Next Administrator. In addition to this procedure, it is also possible to download the NAV road map data on the DVD set directly to the hard disc drive (HDD) integrated in the CIC by inserting the DVDs one by one into the CIC internal DVD drive. It will take approxim
Source components: EQUIPMENT · EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM).
Source record 10147623 at NHTSANHTSA communication ID: 10147607
NHTSA source summary · Original PDF not reviewed by Recallfolio
?SI B13 07 14January 2015 Fuel SystemsTechnical Service This Service Information bulletin supersedes SI 13 07 14 dated October 2014. designates changes to this revision SUBJECT DDE Fault Codes 4862 and 4B82 for EGR Air Mass Plausibility. The Service Engine Soon light is illuminated with one or both of the following fault codes stored in the DDE: z 4B82 - Exhaust-gas recirculation-rate control, control deviation z 4862 - Air system, air to EGR mass flow, plausibility CAUSE Air mass monitoring of the EGR valve is outside allowable limits.
Source components: FUEL SYSTEM, GASOLINE.
Source record 10147607 at NHTSANHTSA communication ID: 10147602
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUBJECT N20, N26, and N55 Engines with Injector Electrical Faults. Any of the following symptoms could occur simultaneously with injector electrical faults stored in the DME: z After the engine is turned off for a short time, it can no longer be started; however, the starter motor turns. z The engine starts but immediately cuts off. z The engine runs erratically or lacks power. z The Service Engine Soon light (MIL) may be on with several poetential faults stored. The DME has malfunctioned due to an internal fault.
Source components: ENGINE · FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM.
Source record 10147602 at NHTSANHTSA communication ID: 10147600
NHTSA source summary · Original PDF not reviewed by Recallfolio
"SUBJECT N63: CBS Oil Service Conversion in ISTA/P. The CBS oil service conversion being performed for the N63 Customer Car Package and timing chain check (SI B11 16 14) does not work correctly. It does not change the interval to the desired 12 months/10,000 miles for the vehicles listed above in the specified production ranges. The ""Conversion, oil service 12months/15,000km/10,000 miles"" is working properly for all other N63 vehicles produced after these dates. Incorrect coding data in the current ISTA/P version"
Source components: ENGINE · EQUIPMENT.
Source record 10147600 at NHTSANHTSA communication ID: 10147595
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUBJECT DME Internal and Valvetronic Faults Set at Cold Ambient Temperatures. The Service Engine Soon light (MIL) can be illuminated with the erroneous internal and Valvetronic faults stored in the DME. The MIL will only come on if the fault has been detected on two (or more) consecutive drive cycles. The following fault codes may be stored in the DME: E Seriesz 36AE - DME, internal fault, Valvetronic: Current implausible One or more of the following secondary faults may also be stored: z 2DE2 - Valvetronic, actuation, voltage phase: Line disconnection z 2DE3 - Valvetronic, actuation, volt phase: Line disconnection z 2DE4 - Valvetronic, actuation, volt phase: Line disconnection F Seriesz 1F0905 - DME, internal fault, Valvetronic: Current implausible One or more of the following secondary faults may also be stored: z 135B10 - Valvetronic, actuation, voltage phase: Line disconnection z 135B11 - Valvetronic, actuation, volt phase: Line disconnection z 135B12 - Valvetronic, actuation, volt phase: Line disconnection Engine performance and driving characteristics are not affected. DME software diagnostic sensitivity.
Source components: ELECTRICAL SYSTEM · ENGINE.
Source record 10147595 at NHTSANHTSA communication ID: 10147593
NHTSA source summary · Original PDF not reviewed by Recallfolio
"This Service Information bulletin and attachment supersedes SI B11 06 14 dated January 2015. designates changes to this revision SUBJECT N63 Engine: Customer Care Package. INFORMATION This bulletin outlines the Customer Care Package program that has been designed exclusively for BMW vehicles with the N63 engine. Vehicles with the N63 high performance engine are engineered with EfficientDynamics that provides fuel economy without compromising on its ""class leading"" power and performance. To ensure these engines keep delivering the ultimate performance, we have designed this Care Package that includes a 6 point check, and if necessary, the replacement of one or more of the following powertrain components: z Hot-Film Air Mass Sensors z PIEZO High Pressure Fuel Injectors z Engine Vacuum Pump z Fuel System Low Pressure Sensor/Feed Line z Fresh Air Intake Turbo Seals z Crankcase Ventilation Lines (Hoses) This engine care package also includes a multi-point inspection of the vehicle, including tire pressures, fluid levels, safety and convenience features. The N63CCP is NOT a mandatory Technical Campaign or Recall (per the authorities). It should only be completed based on parts availability, workshop capacity, and the customer's schedule. Complete all other applicable open Campaigns per the DCS Warranty inquiry and the Key Reader. Perform all recommended, due or qualifying ""time-based"" maintenance service task items as directed by the Key Reader/ISPA Light application. When eligible, also perform the procedure described in SI B61 30 14: 12-Volt Battery Replacement together with performing the N63 Customer Care Package. After completing all the necessary repairs, the vehicle needs to be road tested for 30 minutes to assure the highest standard of performed repairs (Please see ""Warranty Information"" section below)."
Source components: ENGINE · EQUIPMENT · EQUIPMENT:ELECTRICAL.
Source record 10147593 at NHTSANHTSA communication ID: 10057527
NHTSA source summary · Original PDF not reviewed by Recallfolio
BMW: SELECTIVE CATALYST REDUCTION MODULE (SCR) HAS A STORED FAULT, PRESSURE BUILD UP IS LOW, CAUSING SERVICE ENGINE SOON LIGHT TO ILLUMINATE. *
Source components: ENGINE.
Source record 10057527 at NHTSANHTSA communication ID: 10148194
NHTSA source summary · Original PDF not reviewed by Recallfolio
iPhone 6, 6 Plus, 5, 5S, 5C, 4S, 4, and 3GS with iOS 8.x Information. INFORMATION There is one major difference in functionality since iOS 8.0 was released. Scenario: z The customer leaves the vehicle and turns his or her phone off. z He or she turns the phone back on. z He or she enters the vehicle, but does not unlock the phone and start driving. Result: z The phone reconnects to the Bluetooth system (normal). z However, it does not transfer the contact list (not normal). z The contact list in the iDrive will be empty. z The call list in the Kombi will display only phone numbers, but no names. z The hands-free system works for accepting calls and conversing on calls started on the phone. Solution: z Prior to the customer entering the vehicle they must unlock the phone (passkey) With the release of Apple's new iPhone 6, 6 Plus and iOS 8.x software, there have been many questions regarding the new phone and software. The information in the attachment to this Service Information will help answer these questions. A printed copy can be given to the customer if needed. The attachment provides information on the differences between the new iPhone 6, 6 Plus and the previous versions, along with Apple software improvements in the following areas: 1. Visual comparison 2. Connectivity 3. Functionality Refer to the PDF file in the "Attachment" section of this bulletin for complete details. Information on the iPhone 6 is also available via the following: z www.bmwusa.com/bluetooth website NOTE: This SI will be updated as new information is received.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:SOFTWARE · EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10148194 at NHTSANHTSA communication ID: 10148184
NHTSA source summary · Original PDF not reviewed by Recallfolio
BMW Maintenance Program: 12-Volt Battery Replacement Measure.
Source components: ELECTRICAL SYSTEM:12V/24V/48V BATTERY · EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10148184 at NHTSANHTSA communication ID: 10148172
NHTSA source summary · Original PDF not reviewed by Recallfolio
N63 and S63 Engine: High-pressure Fuel Injector Replacement Procedures. The customer complains that one of the following scenarios has been encountered while operating the vehicle: ? During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. ? During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated.? While driving or idling, the engine will misfire and the Service Engine Soon lamp is illuminated. ? Various misfire faults are stored in DME fault memory. CAUSE An internal failure of the high-pressure fuel injector can lead to incorrect operation.
Source components: ENGINE AND ENGINE COOLING.
Source record 10148172 at NHTSANHTSA communication ID: 10148163
NHTSA source summary · Original PDF not reviewed by Recallfolio
N63 Engine: Check the Timing Chain. INFORMATION This bulletin outlines the procedure to check the engine timing chains for wear and should be completed in conjunction with SI B11 06 14 "N63 Customer Care Package". Performing the test plans identified in the procedure below will detect wear at an early stage and if necessary provide a repair solution. To avoid future valvetrain wear, the vehicle must be reprogrammed and a shorter oil service interval must be retrofitted via ISTA/P. Finally, drain and replace the engine's oil and filter. After completing all necessary repairs included in the N63 Customer Care Package and the Timing Chain Check, the vehicle must be test driven for up to 30 minutes to assure the highest standard of performed repairs.
Source components: ENGINE AND ENGINE COOLING.
Source record 10148163 at NHTSANHTSA communication ID: 10148161
NHTSA source summary · Original PDF not reviewed by Recallfolio
INFORMATION This bulletin outlines the Customer Care Package program that has been designed exclusively for BMW vehicles with the N63 engine. Vehicles with the N63 high performance engine are engineered with EfficientDynamics that provides fuel economy without compromising on its "class leading" power and performance. To ensure these engines keep delivering the ultimate performance, we have designed this Care Package that includes a 6 point check, and if necessary, the replacement of one or more of the following powertrain components: ? Hot-Film Air Mass Sensors ? PIEZO High Pressure Fuel Injectors ? Engine Vacuum Pump ? Fuel System Low Pressure Sensor/Feed Line ? Fresh Air Intake Turbo Seals ? Crankcase Ventilation Lines (Hoses) This engine care package also includes a multi-point inspection of the vehicle, including tire pressures, fluid levels, safety and convenience features. The procedure described in this bulletin should be completed in conjunction with performing SI B11 16 14, N63 Engine: Check the Timing Chain. Perform all recommended, due or qualifying "time-based" maintenance service tasks as directed by the Key Reader/ISPA Light application. Note: The procedure in SI B11 16 14 includes an engine oil and filter change. When applicable, also perform the procedure described in SI B61 30 14, 12-Volt Battery Replacement under the BMW Maintenance Program together with performing the N63 Customer Care Package. After completing all necessary repairs, vehicle needs to be test driven for up to 30 minutes to assure the highest standard of performed repairs.
Source components: ENGINE AND ENGINE COOLING.
Source record 10148161 at NHTSANHTSA communication ID: 10057341
NHTSA source summary · Original PDF not reviewed by Recallfolio
BMW: MALFUNCTION WARNING LIGHT FOR ENGINE IS ILLUMINATED DUE TO PURGE AIR SYSTEM MICRO LEAKAGE AND VENTILATION OF FUEL TANK FROM CONTAMINATION. *PE
Source components: ENGINE.
Source record 10057341 at NHTSANHTSA communication ID: 10148423
NHTSA source summary · Original PDF not reviewed by Recallfolio
Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored: z 213901 - Power management: Reduction or shutdown of individual electrical consumer z 8040BD - Reset or deactivation of Terminal 30F z 8040B9 - De-activation of terminal 30B: Top start capability limit reached z 8020E8 - Reset or deactivation of terminal 30F z 800E89 - FRM: start capability limit reached with lights active during stationary mode z 93076B - Deactivation of terminal 30B: upper start capability limit reached z 93076A - Deactivation of terminal 15: upper start capability limit reached, but deactivation preventer active z 93076C - Deactivation of terminal 30B: upper start capability limit reached, but deactivation preventer or legal loads active z 930769 - Deactivation of terminal 15: upper start capability limit reached Note: When the outside temperatures drop below 46F, the charging system is switch to full charge. CAUSE z The check control message (ID 229) is caused by a heavily discharged battery. z The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). z In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. z Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. z The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting
Source components: ELECTRICAL SYSTEM.
Source record 10148423 at NHTSANHTSA communication ID: 10149382
NHTSA source summary · Original PDF not reviewed by Recallfolio
iPhone: Connection Failures with iOS 7. There are various connectivity failures with the iPhone using iOS 7. Some examples are listed below: z Call disconnection z Contact List incomplete z General connection failures Apple software iOS 7 and its variants
Source components: ELECTRICAL SYSTEM.
Source record 10149382 at NHTSANHTSA communication ID: 10149381
NHTSA source summary · Original PDF not reviewed by Recallfolio
Side View Camera Does Not Display Picture. The side view camera does not display a picture: z After engaging reverse gear z Activating the side view camera via the switch on the center console near the gear shift CAUSE z Water (moisture) entering the cable assembly, causing corrosion on the pins in the connector(s) at the camera(s) z Poor cable connection to the camera(s)
Source components: BACK OVER PREVENTION.
Source record 10149381 at NHTSANHTSA communication ID: 10149357
NHTSA source summary · Original PDF not reviewed by Recallfolio
DDE Fault Codes 4882 and 4B82 for EGR Air Mass Plausibility. The Service Engine Soon light is illuminated with one or both of the following fault codes stored in the DDE: 4B82 - Exhaust-gas recirculation-rate control, control deviation 4862 - Air system, air to EGR mass flow, plausibility CAUSE Air mass monitoring of the EGR valve is outside allowable limits.
Source components: ENGINE AND ENGINE COOLING.
Source record 10149357 at NHTSANHTSA communication ID: 10149356
NHTSA source summary · Original PDF not reviewed by Recallfolio
Service Action: Replace the Oxygen Sensor. The oxygen sensor deteriorates prematurely.
Source components: ENGINE AND ENGINE COOLING.
Source record 10149356 at NHTSANHTSA communication ID: 10149282
NHTSA source summary · Original PDF not reviewed by Recallfolio
Engine Damage Due to Debris in Oil Passages. After performing extensive engine repairs (e.g., cylinder head removal), the engine begins to knock and may lose power. Debris has entered the engine oiling passages during cleaning of the engine block and cylinder head mating surfaces during engine repair.
Source components: ENGINE.
Source record 10149282 at NHTSANHTSA communication ID: 10149279
NHTSA source summary · Original PDF not reviewed by Recallfolio
Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Analysis of FASTA data and repeat repair visit reports indicates that there are many fault codes that are stored in the above vehicles, but they are not diagnosed to identify their root cause. Fault codes that are not diagnosed to find their root cause can lead to a repeat repair visit to the workshop by the customer. Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
Source components: EQUIPMENT.
Source record 10149279 at NHTSANHTSA communication ID: 10149278
NHTSA source summary · Original PDF not reviewed by Recallfolio
BMW Customer-Focused Satisfaction (CFS) Program. Based on customer feedback, BMW has determined that during the first three years of service, some vehicles may require specific additional service work. BMW of North America, LLC ("BMW NA") is pleased to announce the Customer-Focused Satisfaction (CFS) Program. This new program's procedure will be available for your center to address these customers' concerns, starting with claim repair dates on or after September 1, 2014. As part of our pledge to deliver the ultimate BMW driving experience, for the above-referenced BMW vehicles, we developed this program to increase our customers' satisfaction by helping to prevent unexpected repair visits.
Source components: EQUIPMENT.
Source record 10149278 at NHTSANHTSA communication ID: 10057567
NHTSA source summary · Original PDF not reviewed by Recallfolio
BMW: SOME VEHICLES EXPERIENCING VARIOUS MESSAGE DISPLAYED REGARDING MALFUNCTION OF LED HEADLIGHT, WITH OPTIONS 0552 AND 0524. *PE
Source components: EXTERIOR LIGHTING:HEADLIGHTS.
Source record 10057567 at NHTSANHTSA communication ID: 10057566
NHTSA source summary · Original PDF not reviewed by Recallfolio
BMW: SOME VEHICLES, WITH 552 OPTION, ARE EXPERIENCING A MALFUNCTION OF LED HEADLIGHT ON ONE WHERE IT FLICKERS ON AN DOFF DURING DRIVING AND THE CONTROL CHECK MESSAGE IS INDICATING DEFECTIVE DRIVING LIGHT OR PARKING LIGHT. *PE
Source components: EXTERIOR LIGHTING:HEADLIGHTS.
Source record 10057566 at NHTSANHTSA communication ID: 10057337
NHTSA source summary · Original PDF not reviewed by Recallfolio
BMW: DUE TO DEBRIS ENTERING OIL PASSAGE OF ENGINE, IT WILL KNOCK AND LOSE POWER, DURING CYLINDER HEAD MATING SURFACES AND CLEANING OF ENGINE BLOCK AFTER REPAIR TO ENGINE. *PE
Source components: ENGINE.
Source record 10057337 at NHTSANHTSA communication ID: 10057336
NHTSA source summary · Original PDF not reviewed by Recallfolio
BMW: NEW SERVICE PROGRAM PROCEDURE IS NOW AVAILABLE REGARDING THE BRAKE FLUID, TIRE PRESSURES, LOCK/STRIKER ADJUSTMENTS FOR TRUNK OR TAILGATE, BATTERY, EXTERIOR LIGHTING. *PE
Source components: EQUIPMENT.
Source record 10057336 at NHTSANHTSA communication ID: 10148034
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Intelligent Battery Sensor Diagnosis Hints. The vehicle enters the workshop with one or more of the following complaints: * Check Control Message related to battery discharge * No-start condition * Consumer power reduction (reduced blower speed, heated seats operation, etc.) * The following fault codes may be stored in the DME a. 2E8B - Intelligent battery sensor, signal b. 2E8C - Intelligent battery sensor, function c. 2E8D - Intelligent battery sensor, signal transmission d. 2E8E - Intelligent battery sensor, communication CAUSE A faulty battery or IBS sensor (not both) The power management system and IBS in the vehicle cannot determine if the battery needs to be replaced. This is normal operation for all E-Series vehicles because they do not have the Advanced IBS sensor that the F-Series vehicles do. An external battery tester (Midtronics EXP-1000) must be used to determine if the battery needs to be replaced. Energy Diagnosis will not prompt for a battery replacement unless the battery is ""aged."" When energy diagnosis identifies the battery as ""aged,"" it means the amount of energy discharge over the course of the life of the battery has reached its maximum (worn out). In most cases, energy diagnosis states that the battery is OK. This is typically an indication of the current State of Charge (SoC), not the State of Health (SoH). The SoC is defined as the current amount of energy left in the battery (displayed as a percentage). The SoH is defined as an evaluation of the condition of the battery over a period of time (displayed as a percentage). For more information about batteries, refer to Training Manual ST051, ""07 Battery Basics."""
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
Source record 10148034 at NHTSANHTSA communication ID: 10056716
NHTSA source summary · Original PDF not reviewed by Recallfolio
BMW: CHECK CONTROL MESSAGE (CCM) IS DISPLAYED, WHEN DOOR OPENS TO FIRST STAGE DUE TO REAR OR FRONT DOOR LOCK AND BOWDEN CABLE COVER AND DOOR LOCK WOULD NEED REPLACING, AS NEEDED. MODEL 2013-15 F15 (X5). *PE
Source components: STRUCTURE:BODY:DOOR.
Source record 10056716 at NHTSANHTSA communication ID: 10148219
NHTSA source summary · Original PDF not reviewed by Recallfolio
Service Action: Inspect Front Driveshaft. The universal joints in the front driveshaft may wear out prematurely.
Source components: POWER TRAIN:DRIVELINE:DRIVESHAFT.
Source record 10148219 at NHTSANHTSA communication ID: 10148215
NHTSA source summary · Original PDF not reviewed by Recallfolio
BMW Customer-Focused Satisfaction (CFS) Program. Based on customer feedback, BMW has determined that during the first three years of service, some vehicles may require specific additional service work. BMW of North America, LLC ("BMW NA") is pleased to announce the Customer-Focused Satisfaction (CFS) Program. This new program's procedure will be available for your center to address these customers' concerns, starting with claim repair dates on or after September 1, 2014. As part of our pledge to deliver the ultimate BMW driving experience, for the above-referenced BMW vehicles, we developed this program to increase our customers' satisfaction by helping to prevent unexpected repair visits.
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10148215 at NHTSANHTSA communication ID: 10148135
NHTSA source summary · Original PDF not reviewed by Recallfolio
ConnectedDrive/BMW Assist System Diagnosis Information. ConnectedDrive/BMW Assist features are partially or completely inoperative. This Service Information bulletin is being published because vehicles are down for an extended period of time when researching system failures with ConnectedDrive or BMW Assist. This Service Information bulletin will assist you both in identifying the issue and providing technical support. CAUSE Not enough information is available for BMW NA engineers to assist the technician in diagnosing the root cause.
Source components: ELECTRICAL SYSTEM:SOFTWARE.
Source record 10148135 at NHTSANHTSA communication ID: 10148120
NHTSA source summary · Original PDF not reviewed by Recallfolio
Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15°F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored: * 213901 - Power management: Reduction or shutdown of individual electrical consumer * 8040BD - Reset or deactivation of Terminal 30F * 8040B9 - De-activation of terminal 30B: Top start capability limit reached * 8020E8 - Reset or deactivation of terminal 30F * 800E89 - FRM: start capability limit reached with lights active during stationary mode * 93076B - Deactivation of terminal 30B: upper start capability limit reached * 93076A - Deactivation of terminal 15: upper start capability limit reached, but deactivation preventer active * 93076C - Deactivation of terminal 30B: upper start capability limit reached, but deactivation preventer or legal loads active * 930769 - Deactivation of terminal 15: upper start capability limit reached Note: When the outside temperatures drop below 46°F, the charging system is switch to full charge. CAUSE * The check control message (ID 229) is caused by a heavily discharged battery. * The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). * In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. * Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. * The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shut
Source components: ELECTRICAL SYSTEM.
Source record 10148120 at NHTSANHTSA communication ID: 10148087
NHTSA source summary · Original PDF not reviewed by Recallfolio
External Engine Oil Leaks and Repairs. During the vehicle's operational life, normal engine oil seepage or sweating, in addition to accumulated road dust, dirt and grime in the engine compartment can cause the appearance of a more severe oil leak. This is further exaggerated by residual oil that remains on the engine assembly after maintenance services are performed, e.g., oil filter changes, "engine oil top-offs," etc. If this visual appearance of accumulated oil on the engine assembly as an "active leak" is misinterpreted, unnecessary gasket repairs/replacements will result. Specifically, our analysis of the claim-related data for vehicles equipped with the engines noted in this bulletin is showing an above-average number of engine gasket repair/replacement claim submissions. The purpose of this bulletin is to provide your workshop with information and a procedure that will help in identifying engine oils leaks that do and do not require a repair.
Source components: ENGINE AND ENGINE COOLING.
Source record 10148087 at NHTSANHTSA communication ID: 10148101
NHTSA source summary · Original PDF not reviewed by Recallfolio
iPhone: Connection Failures with iOS 7. There are various connectivity failures with the iPhone using iOS 7. Some examples are listed below: * Call disconnection * Contact List incomplete * General connection failures CAUSE Apple software iOS 7 and its variants.
Source components: ELECTRICAL SYSTEM.
Source record 10148101 at NHTSANHTSA communication ID: 10056099
NHTSA source summary · Original PDF not reviewed by Recallfolio
BMW: WHEN USING IPHONE, VARIOUS CONNECTIVITY FAILURES OCCUR, SUCH AS DISCONNECTION OF CALL, LIST OF CONTACTS INCOMPLETE, DUE TO THE VARIANTS AND SOFTWARE USED. MODEL 2008-2014.
Source components: COMMUNICATION · ELECTRICAL SYSTEM:SOFTWARE.
Source record 10056099 at NHTSANHTSA communication ID: 10056094
NHTSA source summary · Original PDF not reviewed by Recallfolio
BMW: DUE TO GUIDE SUPPORTS BEING INCORRECT, THE REAR SHOCK ABSORBERS WERE ASSEMBLED, WHICH WITHIN A LOW MILEAGE CAUSES A RATTLING NOISE. MODEL F15 (X5). *PE
Source components: SUSPENSION:REAR:SHOCK ABSORBER.
Source record 10056094 at NHTSANHTSA communication ID: 10148318
NHTSA source summary · Original PDF not reviewed by Recallfolio
Tire Pressure Monitor System (TPMS) Functional Changes. INFORMATION There has been a disruption in the production and supply chain of certain electronic components. These events have influenced global manufacturing facilities, including the automotive sector. In order to fulfill customer demand and maintain production schedules, BMW has made a change to the Tire Pressure Monitor System of certain vehicles. https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/16234.2.B360211.... 6/8/2014 Page 2 of 2 Although the basic system operation and function remain the same, changes have been made to the vehicle's display elements when a low tire pressure condition occurs. The following points apply to vehicles produced during the period listed above: * The Tire Pressure Monitor System continues to meet all federal requirements. * When a low tire pressure condition is detected, a general system warning is issued. The warning will be displayed in the instrument cluster (KOMBI) and/or Control Display, depending on the vehicle's equipment level (refer to the attachment). * When a driver is alerted to a low pressure condition, all four tires should be inspected for damage and proper inflation. The system components, wheel electronics and central antennae/module are fully compatible with current replacement parts. This functional change represents a running production change and is not a defect in materials or workmanship. Any further changes to the system function or components will be communicated in a future bulletin. It is imperative that all service personnel be familiar with these changes. WARRANTY INFORMATION Not applicable.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS.
Source record 10148318 at NHTSANHTSA communication ID: 10148308
NHTSA source summary · Original PDF not reviewed by Recallfolio
N63 and S63 Engine: High-pressure Fuel Injector Replacement Procedures. The customer complains that one of the following scenarios has been encountered while operating the vehicle: * During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. * During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated. While driving or idling, the engine will misfire and the Service Engine Soon lamp is illuminated. * Various misfire faults are stored in DME fault memory. CAUSE An internal failure of the high-pressure fuel injector can lead to incorrect operation.
Source components: FUEL SYSTEM, GASOLINE · FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM:INJECTORS.
Source record 10148308 at NHTSA