2016 BMW 328I Manufacturer communications & TSBs.Page 4
Original record summaries, dates and identifiers for this model-year. Records 301–387 of 387, ordered newest first. Dated records on this page: Jan 1, 2015–Feb 1, 2016.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Feb 1, 2016Service Bulletin/Repair Instructions
B130315
NHTSA communication ID: 10151079
NHTSA source summary · Original PDF not reviewed by Recallfolio
SI B13 03 15 February 2016 Fuel Systems Technical Service This Service Information bulletin supersedes SI B13 03 15 dated March 2015 and replaces SI B13 04 13 dated March 2014. SUBJECT N20, N26, N55, N63TU, S63TU and S55 Engines: Bosch Injector ETK Part Number Error. The current version of the ETK incorporates multiple part number errors for the Bosch type injectors. Ordering the injectors by VIN number or manual identification in ETK may result in an incorrect part number.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Service Information bulletin supersedes SI 12 33 14 dated December 2015. SUBJECT Fault Code 1D2008 Stored in DME. The Service Engine Soon light is on. Fault Code 1D2008: Map thermostat: jammed open is stored in the DME. There may also be a complaint of low heat output with lower outside temperatures. CAUSE During the engine warm-up, the engine coolant does not reach operating temperature within the DME's allowable time limits. This is caused by either a faulty thermostat inside the transmission oil heat exchanger or a faulty engine characteristic map thermostat.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT ADAPTIVE/MOBILITY · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The upper crankshaft guide bearing may wear out prematurely. The wear on the upper guide bearing can cause the clutch pedal to malfunction during shifting. The Engine Malfunction warning may be illuminated and a fault will be stored in the DME memory for the crankshaft sensor. Noise may be heard from the lower engine and transmission bell housing area. Engine damage can occur in rare occasions.
Source components: ENGINE · EQUIPMENT ADAPTIVE/MOBILITY · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
February 2016 Engine Technical Service This Service Information Bulletin supersedes SI B11 16 15 dated September 2015 SUBJECT N20 and N26 engine: Smoke from Exhaust when Starting a Cold Engine. When starting a cold engine, blue smoke can be seen emitting from the exhaust tailpipe for approximately 10-20 seconds. No turbo charger boost faults are stored and no drivability issues can be detected. CAUSE When the vehicle is parked overnight the engine oil pressure will equalize and may leak past the turbo charger exhaust side turbine seal.
Source components: ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER · ENGINE AND ENGINE COOLING:ENGINE:OTHER FUEL TYPES:TURBO/SUPERCHARGER · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"?SUBJECT During the QC1 the BMW Assist Test Call Fails . After the transport mode is deleted (during the QC1), a BMW Assist (SOS) test call is made by pressing the SOS/ E-Call button. However, the call only connects via voice (no data is transmitted). The operator indicates that a crash call has been sent. ATM fault code ""B7F348 - Provisioning without signature OTA"" is stored. The provisioning of the ATM (Advanced Telematics Module) has failed."
NHTSA source summary · Original PDF not reviewed by Recallfolio
?SUBJECT Incremental Map Update of the NBT EVO Head Unit . Customers may be receiving onscreen messages concerning updates of their navigation system. Database mapping procedure in vehicles with the NBT EVO Head Unit (Head Unit high 2) has been changed to automatic, periodic, Over- the-Air (OTA), regional, incremental updates. INFORMATION Customers may not be familiar with the messages seen prior to, during, and after this update which may prompt inquiries. The following information provides an overview of the automatic OTA process that has replaced the previously required BMW center visit for navigation map updates. UPDATE DETAILS Updates can occur up to 4 times per year, ensuring that customers have the newest map data available. At a minimum, updates occur during first 2 years of vehicle ownership at no additional charge to the customer. At additional customers expense updates can also occur for up to 4 years (depending upon vehicle retail date and BMW assist options selected). Please check the BMW connected drive service cockpit for details on an individual vehicles coverage. To access the BMW connected drive service cockpit refer to the attachment.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Whistling Noise Coming from the Center Vent - A/C is Off . A very high pitched whistling or beeping noise is heard coming from the center vents. The flow of refrigerant through the expansion valve at certain temperature differentials.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Whistling Noise Coming from the Center Vent - A/C is Off . A very high pitched whistling or beeping noise is heard coming from the center vents. The flow of refrigerant through the expansion valve at certain temperature differentials.
NHTSA source summary · Original PDF not reviewed by Recallfolio
?Clock gains or loses time. The time displayed in the KOMBI (instrument cluster) may gain or lose a few minutes each week. Internal KOMBI calculation error.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Vehicles which have had the Instrument Cluster (KOMBI) replaced may display incorrect CBS (Condition Based Service) data after programming. AFFECTED VEHICLES Vehicles which require this Service Action to be completed will show it as ""Open"" when checked either in the ""Service Menu"" of DCSnet (Dealer Communication System) or with the Key Reader. Incorrect SW calibration loaded after KOMBI replacement."
NHTSA source summary · Original PDF not reviewed by Recallfolio
SI B11 14 15 October 2015 Engine Technical Service This Service Information bulletin supersedes SI B11 14 15 dated October 2015. The plastic oil filter housing may fail and lead to an internal and/or external engine oil or coolant leak.
NHTSA source summary · Original PDF not reviewed by Recallfolio
XM Satellite Radio Reception. INFORMATION Currently Satellite Radio is provided by SiriusXM for BMW customers. SiriusXM is the only company currently broadcasting Satellite Radio in North America. Satellite radio is broadcast from two different sets of Satellites using different earth orbits. XM uses geosynchronous (GEO) satellites located roughly above the equator. This means that the satellite signal to some parts of the United States can come in at an angle as low as 32 degrees to the horizon. This is different than Sirius Satellites in a Highly Elliptical Orbit (HEO) which currently come in to the vehicle at a higher angle to the horizon. As of April 2016 Sirius equipped head units will move to the XM Satellites constellation and will show the same location based cutouts. SiriusXM is currently updating the repeater network to cover areas of low reception, but the general disadvantage of geostationary satellites can't be compensated completely. Buildings, hills, trees, highway sound blocking walls or any other obstacles might block the satellite signal coming from the south at a 32 degree elevation angle and might cause audio cut outs in absence of terrestrial repeaters. Reception quality decreases the further north you travel, as the angle of the incoming signal gets flatter. Adverse weather conditions will affect reception. Sirius XM will increase the amount of Sirius and XM repeaters gradually to improve situation in metropolitan areas. When investigating Satellite Radio cutouts or a temporary loss of reception: Please compare to a similarly equipped vehicle. Do not compare an XM equipped vehicle to a Sirius equipped vehicle. Replace no parts Customers should direct all reception complaints to one of the following: BMW Customer Relations department at either 1-800-831-1117 or customerrelations@bmwusa.com BMW Genius Hotline 1-844-443-6487 or to the dealers onsite BMW Genius Customers must provide the exact location (street address or Latitude/Longitude), weathe
NHTSA source summary · Original PDF not reviewed by Recallfolio
Instrument Cluster Outside Temperature Display Implausible. INFORMATION This service information bulletin provides technical, diagnostic and/or repair-related information. Eligible and Covered Work/Repairs To submit a claim for the repair of a verified defect in materials or workmanship, please following the established and applicable warranty policy and procedures together with the using corresponding defect code and labor operations provided in the KSD2.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Head-Up Display (HUD) Rattling Noises During Image Adjustment or While Driving. When operating the Head-Up Display (HUD) adjustment a noise can be heard from inside the dashboard behind the Instrument Cluster. While driving over rough roads something can be heard rattling inside the HUD. Internal HUD failure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"The Low Washer Fluid Warning Light is illuminated when the Washer Fluid Tank is Full. INFORMATION The use of a ""non-approved"" washer fluid can cause the low fluid warning light to come on even when the reservoir is full. An analysis of parts returned to warranty has shown the sensor is operating correctly. Do not replace the reservoir with integrated sensor for these situations. We recommend using ""BMW Group approved"" washer fluid when servicing the vehicle or performing repairs on the windshield washer system. Refer to ISTA document ""FB-GZ-B17A-F20 Washer fluid level sensor"" for information on how this capacitive sensor operates. If the correct washer fluid is being used, diagnose the system using normal troubleshooting with ISTA. A fault code may be stored if an electrical fault occurs in the circuit. PARTS INFORMATION Part NumberDescriptionQuantity83 19 2 406 220BMW WWS Cold Weather Concentrate 35% 55 GalAs needed83 19 2 361 205BMW Windshield Washer Concentrate 1 GalAs neededNote: As applicable, do not exceed your state's maximum for the allowable amount/percentage of ""Washer Concentrate"" that can be used when mixing the windshield washer fluid solution. WARRANTY INFORMATION The issue described in this bulletin is not a vehicle-related defect in materials or workmanship. If a vehicle repair is required as a result of this issue, it is are not claimable under a BMW limited warranty."
NHTSA source summary · Original PDF not reviewed by Recallfolio
?SI B51 24 15December 2015 Body EquipmentTechnical Service This Service Information bulletin supersedes SI B51 24 15 dated September 2015. designates changes to this revision SUBJECT Groaning Noise from the Exterior Mirror. A groaning noise is heard coming from the area around the outside mirror when opening and closing the door. The noise is more noticeable when the door is fully open to the end stop. CAUSE The outer front door weather strip rubs against the mirror housing.
NHTSA source summary · Original PDF not reviewed by Recallfolio
?SI B34 08 14 Brakes December 2015 Technical Service This Service Information bulletin supersedes SI 34 08 14 dated July 2015. designates changes to this revision SUBJECT Ticking Noise from Front Axle When Cornering. The customer may complain of a ticking noise from the front axle when cornering, maneuvering, parking or pulling away from a parking space. The noise can be heard as a light metallic ticking from the front outer cornering wheel. Movement between the brake disc and wheel bearing hub.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Fault Code 1D2008 Stored in DME. The Service Engine Soon light is on. Fault Code 1D2008: Map thermostat: jammed open is stored in the DME. There may also be a complaint of low heat output with lower outside temperatures. CAUSE During the engine warm-up, the engine coolant does not reach operating temperature within the DME's allowable time limits. This is caused by either a faulty thermostat inside the transmission oil heat exchanger or a faulty engine characteristic map thermostat.
Source components: ENGINE · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Delivery Stop: B58 Engine - Check Crankshaft Bearing Shells.A Delivery Stop has been issued on F30 and F32 certain vehicles produced from July 2015 (start of production) to December 2, 2015. These vehicles may have upper guide bearing shells that may exhibit wear at low mileage. There are 45 vehicles affected by this stop. For your convenience, attached you will find the list of affected VINs. This bulletin will be updated with repair instructions and warranty information when it becomes available. Affected vehicles can be identified with a ?Vehicle Comment? in DCS Warranty Vehicle Inquiry or ISPA Light with a specific description.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Radio reception disturbed when the taillights are active. Page 1 of 2 November 2015 Technical Service Radio reception interference may be observed between 90.0 MHz and 100.0MHz on the FM band. The noise is present when the taillights are active (lights or braking). Right Rear taillight assembly problem
NHTSA source summary · Original PDF not reviewed by Recallfolio
HU-H: Headunit Resets Intermittently or Permanently. The HU-H (Headunit-High) resets intermittently or permanently. ? The display is inoperative and there is no audio output ? Automatic system start-up after a couple of seconds CAUSE Software error in the HU-H
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
A/C Cooling: Intermittent Reduction of Air Flow. Customer may complain of reduced air flow when the air conditioning system is operated for an extended time, usually longer than 30 minutes. INFORMATION Possibility of reproducing this situation is improved by the following conditions ? High outside ambient temperature ? High humidity Note: It is very difficult to duplicate this issue. The fault may be reproduced under the following conditions: ? Air-conditioning system switched on ? Driving Experience switch NOT set to Eco Pro ? Slower fan speeds ? Temperature setting below 68°F (20°C) ? Trip duration at least 30 minutes ? Outside temperature above 68°F (20°C) NOTE: After parking the vehicle or switching off the air-conditioning system for at least 20 minutes, the symptom disappears (ice melts off evaporator and puddles under the car from the A/C drains.). Evaporator starts to freeze up due to the position of the evaporator temperature sensor.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · EQUIPMENT:APPLIANCE:AIR CONDITIONER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"The illumination (back lighting) for the E-Call (Emergency/SOS call) button in the FZD (sunroof module) overhead console does not work. This picture shows the E-Call button illumination (back lighting) not working. Note: Pressing the E-Call button will start an SOS call, even though the back lighting is not working.This picture shows E-Call illumination (back lighting) working. AFFECTED VEHICLES This Service Action involves the F34 (3 Series Gran Turismo) and F36 (4 Series Gran Coupe) models, produced from 7/27/2015 to 7/30/2015. Please perform it the next time this vehicle comes to your workshop. Vehicles which require this Service Action to be completed will show it as ""Open"" when checked either in the ""Service Menu"" of DCSnet (Dealer Communication System) or with the Key Reader. Missing wiring harness for the illumination of the E-Call button."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Active Sound Design ASD inoperative after programming. After programming with ISTA/P V3.56.1 Active Sound Design (ASD) no longer provides simulated engine sounds A fault is stored in the ASD module. Fault Code 8053A5 ""ASD; invalid coding data for equalizing"" Invalid ASD coding data"
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT:ELECTRICAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Water Ingress into the Luggage Compartment after opening the Tailgate. A small quantity of water may enter the luggage compartment after opening the tailgate CAUSE The water drain hose(s) on the rear spoiler is blocked.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Check Control Message: Tire Pressure Monitor (RDCi) Failure. A Check Control Message states Tire Pressure Monitor (RDCi) has failed CAUSE Hardware in the remote control unit (FBD3 antenna)
Source components: TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Grinding or cracking noise when putting vehicle in gear/ ""Drive Disturbed"" displayed. A metallic grinding or cracking noise is heard from the rear of the vehicle when selecting Drive or Reverse. There may also be a Check Control message ""Drive Disturbed"" displayed. CAUSE The inner and/or outer universal joint on the right and/or left rear output shaft has failed."
NHTSA source summary · Original PDF not reviewed by Recallfolio
ConnectedDrive Messages Are Not Received In the Vehicle. One or both of the following may occur: SMS based messages are not received in the vehicle. These are: Text messages - Office feature MyInfo Google send to car - addresses and Points of Interests (POI) Concierge The activation code is not accepted by the ConnectedDrive Portal. Software error in the HU-H (Head unit High).
NHTSA source summary · Original PDF not reviewed by Recallfolio
"HU-B: Bluetooth Connection Fails Sporadically. The Bluetooth system works intermittently. One or more of the following scenarios may occur: Bluetooth pairing is not possible - display shows ""Please wait"" Unable to select the check box to activate Bluetooth Device does not reconnect to the vehicle after a key cycle Audio interference noise is heard listening to iPod etc. When trying to access the user manual, the display shows ""Please wait"" Incorrect software installed in the HU-B (Headunit Basic)."
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Parking Maneuvering Assistant and Park Distance Control Failure. After activating the PMA (Parking Maneuvering Assistant) or PDC (Park Distance Control), the system stops functioning and a CCM (Check Control Message) is displayed advising the driver of the failure. The following fault code is stored in the PMA control unit 0x481E4D - PMA control unit internal, internal ASIC fault Software error in the PMA control unit Affected I-Level: F2x from F020-15-03-500 F3x from F020-15-07-500
Source components: LANE DEPARTURE: LANE KEEP: STEERING ASSIST.
NHTSA source summary · Original PDF not reviewed by Recallfolio
IHKA - Outlet Temperature is Different on Both Sides. The IHKA settings on the left- and right-hand side are identical. The outlet temperature for both sides is different. Software application error in IHKA.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"IHKA - Blower Runs in Emergency Mode. After the ignition is turned off and the vehicle is locked, the heating and air conditioning blower motor runs continuously. The next time the vehicle is started there may be the CCM (Check control message) displayed for ""Increased battery discharge"". CAUSE The blower output stage receives an invalid LIN bus signal during operation and switches to emergency mode. The blower will continue to run with the specified emergency mode after the ignition is turned off and the vehicle is locked."
NHTSA source summary · Original PDF not reviewed by Recallfolio
IHKA - Recirculation Function Changes from Manual to Automatic. While driving, the air recirculation button on IHKA changes by itself from manual to automatic or automatic to manual mode. CAUSE The IHKA operating software is too sensitive.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Reverse Light is Intermittently Inoperative. CCM (Check control message) is displayed indicating a ""reverse light"" is out. CAUSE There is a weak spring in bulb socket or bulb carrier (on the luggage compartment lid) which is causing a bad contact with the bulb."
Source components: EXTERIOR LIGHTING:BACK UP LIGHTS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Under certain conditions, the additional radiator could not be cooled sufficiently. This could cause the engine to overheat. The engine power would be reduced and a Check Control Message would appear. AFFECTED VEHICLES This Delivery Stop involves F34 (3 Series Gran Turismo) produced from July 13, 2015 to July 18, 2015. Vehicles which require this Delivery Stop to be completed will show it as ""Open"" when checked either in AIR, the ""Service Menu"" of DCSnet (Dealer Communication System) or with the Key Reader."
Source components: ENGINE AND ENGINE COOLING:COOLING SYSTEM:RADIATOR ASSEMBLY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Driver or Passenger's Front Doors Handles Inoperable. Sporadically it is not possible to open the driver or passenger's front door from the outside or inside door handle. Multiple attempts will eventually open the door. Comfort access operation of the outside door handle works properly. This situation occurs at temperatures below 37 °F. CAUSE Incorrect routing of the Bowden cable.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Groaning Noise from the Exterior Mirror. A groaning noise is heard coming from the area around the outside mirror when opening and closing the door. The noise is more noticeable when the door is fully open to the end stop. CAUSE The outer front door weather strip rubs against the mirror housing.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The Driver's Door Can No Longer Be Opened from the Outside. The driver's door cannot be opened from the outside by the door handle. The door still can be opened from the inside. CAUSE The Bowden cable has become detached.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Check Control Message: Tire Pressure Monitor (RDCi) Failure. A Check Control Message states Tire Pressure Monitor (RDCi) has failed CAUSE Hardware in the remote control unit (FBD3 antenna)
Source components: TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Shudder from the Driveline on Vehicles with xDrive. There is a shudder or vibration from the driveline when taking off from a stop, or when accelerating at highway speeds. CAUSE Possible multiple root causes related to the engine, wheels & tires, suspension components or internal wear on the clutch plates of the xDrive transfer case.
Source components: POWER TRAIN:DRIVELINE · WHEELS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
?N20 and N26 engine: Smoke from Exhaust when Starting a Cold Engine. When starting a cold engine, blue smoke can be seen emitting from the exhaust tailpipe for approximately 10-20 seconds. No turbo charger boost faults are stored and no drivability issues can be detected. Engine oil leakage into the induction system and/or the turbo charger assembly.
Source components: ENGINE · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Instrument Cluster: CBS ""Running-in Check"" is Displayed. After replacing and / or programming the instrument cluster with ISTA/P 3.55.0 or higher (integration Level F020-15-03-501 or higher), the CBS (Condition Based Service) displays ""running-in check"" or ""1200 mile service is due"". The parameters of the CBS scopes for oil service, brake fluid, etc, can also be implausible or invalid. CAUSE Error in the CBS mapping data in the FEM (Front Electronics Module) and corrupt data in the instrument cluster during programming."
NHTSA source summary · Original PDF not reviewed by Recallfolio
Vibration or Shudder from Driveline when Accelerating from a Stop. Chassis stabilization warning is displayed. Vehicle may exhibit a shudder or vibration when taking off from a stop. One or more of the following fault codes may be stored: LMV ? 440101 - Transfer box (VTG): End of transmission service life reached ? 440105 - Transfer box (VTG ) Calibration Faulty ? 440115 - Transfer box (VTG): Calibration angle deviation outside tolerance? 44011B - Set torque outside of the torque characteristic curve EGS ? 420611 - DSC interface (wheel speed): non-permitted deviation of wheel speed (actual speed of wheel RL/FL/RR/FR, 0x254) from output speed and turbine speed DSC ? 48097D - Transfer box: Fault, clutch position known, only rear-wheel drive These symptoms or faults would be stored on a vehicle with low mileage (< 12,500 miles). CAUSE A front or rear differential with the incorrect gear ratio was installed in the car. The front and rear differentials need to be geared exactly the same for the xDrive to function properly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NAV Road Map Installation Using USB Stick. INFORMATION The Navigation road map can be installed onto the head unit in the vehicle using a USB stick connected to the USB connector in the center console in the vehicle. ? 32GB USB stick is necessary ? Desired NAV road map version can be retrieved from the HDD-Update console PROCEDURE 1. Copy the desired NAV road map from the HDD-Update console onto a 32GB USB stick. Refer to Attachment. 3. When prompted, enter the 20-digit enabling code. 4. Start the NAV road map installation and follow the on-screen instructions. WARRANTY INFORMATION Not applicable. ATTACHMENTS View PDF attachment B651015_Attachment.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Horn Blows when Unlocking Vehicle. The customer states that the vehicle horn sounds briefly when unlocking the vehicle or opening the door. In some cases, the washers spray briefly on the windshield. Front Electronics Module (FEM) software error
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Affected vehicles in dealer inventory must not be retailed or delivered until the label is removed. Vehicles at ports of entry will be remedied prior to dealer delivery. On affected vehicles, there is an incorrect label regarding the appropriate engine oil. Affected vehicles can be identified with a ""Vehicle Comment"" in the DCS Warranty Vehicle Inquiry or ISPA Light. Remove the engine oil label (located in the front or rear of the hood)."
NHTSA source summary · Original PDF not reviewed by Recallfolio
Ticking Noise from Front Axle When Cornering. The customer may complain of a ticking noise from the front axle when cornering, maneuvering, parking or pulling away from a parking space. The noise can be heard as a light metallic ticking from the front outer cornering wheel. Movement between the brake disc and wheel bearing hub.
Source components: POWER TRAIN:AXLE ASSEMBLY · SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC · WHEELS:HUB.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Power-Assisted Steering Failure. The power-assisted steering fails with a warning lamp in the instrument cluster or a check control message in the Central Information Display. In some cases, the Dynamic Stability Control warning lamp (DSC) in the instrument cluster may also be illuminated. Failure of the power-assisted steering may be caused by various software-related issues. The following codes may be stored in the fault memory of the Electric Power Steering (EPS): Scenario 1: 0x4823E1 Scenario 2: 0x4823CB/0x4823CC Scenario 3: 0x4823D2 and/or 0x4823EC Scenario 4: 0x48239C (DSC warning lamp lights up in the instrument cluster) Scenario 5: No communication with the EPS is possible (not accessible using diagnostics) Scenario 6: 0x4823EE and 0x4823C2
Source components: SERVICE BRAKES, HYDRAULIC:POWER ASSIST · STEERING · STEERING:ELECTRIC POWER ASSIST SYSTEM · STEERING:HYDRAULIC POWER ASSIST SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Engine Malfunction Warning Illuminated with FC 193208: Fuel Level Plausibility Stored in DME. The customer states that the engine malfunction warning lamp is illuminated, and while filling the fuel tank, the fuel gauge did not show the proper fill level. After the vehicle is driven a short distance, the fuel gauge will update to full. When diagnosed, the following fault is stored in the DME: ? FC 193208 Fuel level, plausibility: deviation between consumption and level change Please proceed to the Procedure section. Vehicles with option 610 (Head-Up Display) are not affected. Please follow the ISTA/D test plan for the applicable faults stored in the DME, including the one listed in this bulletin. CAUSE A software error in the instrument cluster causes the fuel gauge to incorrectly update while refilling. The error occurs when the vehicle is powered up after refilling.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Front Parking Lights Inoperative. After programming the vehicle with ISTA/P 3.56.1, both front parking lights (integrated in the headlights) have been deactivated and no Check Control message is displayed. CAUSE FEM software error in ISTA/P 3.56.1
Source components: ELECTRICAL SYSTEM · EXTERIOR LIGHTING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Horn(s) Fail to Work. While trying to activate the horn, one or both horns fail to work. One or more of the following fault codes can be stored in the FEM: ? ""8044A3 - Wiring, horn short circuit to earth"" ? ""8044A4 - Wiring, horn short circuit to positive"" ? ""8044A5 - Wiring, horn relay is defective or short circuit to positive"" Water has entered the horn and caused it to fail internally (shorted out)."
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:HORN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Check Control Message: Tire Pressure Monitor (RDCi) Failure. A Check Control Message states Tire Pressure Monitor (RDCi) has failed CAUSE Hardware in the remote control unit (FBD3 antenna)
NHTSA source summary · Original PDF not reviewed by Recallfolio
8HP: Transmission Fluid Loss from Cooler Lines Connections. There is a transmission fluid leak in the area around the oil cooler lines (on the transmission side). CAUSE Damaged o-rings due to unfavorable cooling line connection tolerances
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
HU-H: Headunit Resets Intermittently or Permanently. The HU-H (Headunit-High) resets intermittently or permanently. ? The display is inoperative and there is no audio output ? Automatic system start-up after a couple of seconds CAUSE Software error in the HU-H
NHTSA source summary · Original PDF not reviewed by Recallfolio
Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15°F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can occur. The check control message (ID 229) is caused by a heavily discharged battery. ? The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). ? In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. ? Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. ? The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting down certain electrical consumers.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Removal Process: B-Pillar High Gloss Trim Protective Wrap. INFORMATION ONLY The key for successful wrap removal is to have the body cool (below 60 degrees) and dry. The recommendations are as follows: ? Before removing the B-pillar wrap, make sure the car body is dry and cool. ? Removing the wrap in the early morning hours will provide the best results. ? In warmer climates, it is recommended to keep the cars in an A/C environment at least overnight, and then, in the morning, slowly peel off the wrap. ? If there is still any glue residue left, use masking tape to cover the glue area. Wait for a few minutes, and then pull off the masking tape. Repeat this process until the glue is fully removed. [ Copyright (c)2015 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/233...6/4/2015
NHTSA source summary · Original PDF not reviewed by Recallfolio
Valve Stem Replacement with Wheel Electronics. INFORMATION The valve stems are single-use only, and must be replaced every time the wheel electronics are replaced. If you loosen the nut (1), you must replace the valve stem. Failure to replace the valve stem will lead to a pressure leak. The proper repair procedure can be found in REP 3611533. Not applicable. [ Copyright (c)2015 BMW of North America, Inc. ] Page 1 of 3 Page 1 of 1 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015 Page 1 of 3 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015
NHTSA source summary · Original PDF not reviewed by Recallfolio
?SI B12 21 14May 2015 Engine Electrical SystemsTechnical Service This Service Information bulletin supersedes SI B12 21 14 dated April 2015. designates changes to this revision SUBJECT Engine Malfunction Warning Illuminated with FC 193208: Fuel Level Plausibility Stored in DME. The customer states that the engine malfunction warning lamp is illuminated, and while filling the fuel tank, the fuel gauge did not show the proper fill level. After the vehicle is driven a short distance, the fuel gauge will update to full. When diagnosed, the following fault is stored in the DME: ? FC 193208 Fuel level, plausibility: deviation between consumption and level change Please proceed to the Procedure section. Vehicles with option 610 (Head-Up Display) are not affected. Please follow the ISTA/D test plan for the applicable faults stored in the DME, including the one listed in this bulletin. CAUSE A software error in the instrument cluster causes the fuel gauge to incorrectly update while refilling. The error occurs when the vehicle is powered up after refilling.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Surround View Camera Last User Mode Operation Change. After programming with ISTA/P 2.53.5 or a more recent version, the rear camera view is displayed when the reverse gear is selected. The vehicle does not remember the last user mode (surround/top camera view). INFORMATION An operational concept change for the surround/top camera view was introduced with ISTA/P 2.53.5 (I-level Fxx-14-07-505). When the reverse gear is selected, the default view will be the rear camera. The surround/top camera view has been removed from the last user mode function. This is to meet the upcoming (new) federal regulations regarding rear view cameras. Note: The surround/top camera view is available, but the driver must manually switch the camera view using the iDrive controller.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"N20 and N26 Engines: ETK Injector Part Number Error. INFORMATION The current version of ETK has an error on screen 13_1417: ""High -pressure pump/Tubing."" When selecting the high-pressure pump, the screen states ""only in conjunction with injector."" Disregard this statement and only replace the high-pressure pump. If injectors need to be replaced, enter the VIN of the vehicle into the ETK and select the part numbers found on screen 13_1416: ""High-pressure rail/injector/mounting."" Always enter the VIN for the vehicle into ETK when searching for parts. When the ETK is corrected, this SIB will be updated. WARRANTY INFORMATION Not applicable. [ Copyright (c)2015 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/224...5/4/2015"
NHTSA source summary · Original PDF not reviewed by Recallfolio
Engine Malfunction Warning Illuminated with FC 193208: Fuel Level Plausibility Stored in DME. The customer states that the engine malfunction warning lamp is illuminated, and while filling the fuel tank, the fuel gauge did not show the proper fill level. After the vehicle is driven a short distance, the fuel gauge will update to full. When diagnosed, the following fault is stored in the DME: ? FC 193208 Fuel level, plausibility: deviation between consumption and level change Please proceed to the Procedure section. Vehicles with option 610 (Head-Up Display) are not affected. Please follow the ISTA/D test plan for the applicable faults stored in the DME, including the one listed in this bulletin. CAUSE A software error in the instrument cluster causes the fuel gauge to incorrectly update while refilling. The error occurs when the vehicle is powered up after refilling.
NHTSA source summary · Original PDF not reviewed by Recallfolio
One or both of the situations listed below may be encountered: ? Android device connection stability (dropped calls) ? Third-Party App Metadata: The album art and song title do not update when streaming audio from Pandora or Spotify, etc. New KISU (Customer Initiated Software Update) software is available on the TIS website. This software improves the Bluetooth functionality in our vehicles, and it helps to keep us up-to-date with technology innovation.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Remote Control Not Detected and/or Engine Will Not Start. One or more of the following situations can occur: 1. The remote control is not detected and the check control message (CCM) ""No remote control. Unable to start"" or ""Hold the remote control on the steering column"" is displayed. ? Fault code ""D90D1E - LIN bus error FBD receiver 1"" is stored. 2. The engine does not start with the CCM with ""Battery in the key is dead."" However, it must work when used with the second key. ? Fault Code ""9308B0 - ID transmitter: Battery undervoltage"" is stored. 3. The remote control is not detected and the CCM ""Central locking does not open,"" and/or ""Engine fails to start"" is displayed. An outside influence is causing interference with the remote control or the battery in the remote control key is defective."
NHTSA source summary · Original PDF not reviewed by Recallfolio
Horn Blows when Unlocking Vehicle. The customer states that the vehicle horn sounds briefly when unlocking the vehicle or opening the door. In some cases, the washers spray briefly on the windshield. Front Electronics Module (FEM) software error
NHTSA source summary · Original PDF not reviewed by Recallfolio
General Electrical Systems Technical Service. Various Check Control Messages Caused by Shorted K-CAN. The customer states that one or more of the following CC messages are displayed: ? 627 - Steering behavior: Drive moderately ? 070 - Steering: Drive moderately ? 765 - Rear-end collision restricted ? 850 - Pedestrian warning restricted ? 236 - Driving stabilization: Drive moderately ? 299 - SOS call system failure ? 042 - Brake system: Drive moderately After performing a vehicle test, one or more of the following fault codes are stored: ? ACSM - C9549A Message faulty (seat memory), ACSM receiver, driver's seat module transmitter ? FEM - D91DE0 No message, receiver FEM, transmitter TMSL ? FEM - D91EE5 No message, receiver FEM, passenger seat module transmitter ? ACSM - C9540C Message missing, receiver ACSM, transmitter FEM ? TMSL - D95402 Message missing, receiver TMSL, transmitter FEM ? KOMBI - E11454 No message, receiver KOMBI, transmitter REM ? FEM - D91DE6 No message, receiver FEM, transmitter TMSL ? TMSR - D99401 Message missing, receiver TMSR, transmitter FEM ? TMSR - D99402 Message missing, receiver TMSR, transmitter FEM ? FEM - 8041BA AHL system faulty ? FEM - D916C3 No message, receiver FEM, transmitter TCB ? ZBE - E2D403 No message, receiver CON, transmitter FEM-ZGM ? TRSVC - CA9428 Message incorrect, receiver TRSVC, transmitter PDC-REM ? TMSL- D95401 Message missing, receiver TMSR, transmitter FEM ? HU-H - S0397 MOST configuration was not stored ? TCB - E1445F KCAN2 or KCAN4: Line fault/electrical fault ? FEM - 8041B6 LWR faulty ? REM - E58468 Body CAN2; communication fault ? TRSVC - CA9427 Message incorrect, receiver all around vision camera, transmitter PDC/REM ? FEM - D91CEC Message missing, receiver FEM, transmitter REM Shorted KCAN wiring under driver or passenger seat.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Front Floor Mats Do Not Stay in Place. The Velcro patch attached to the bottom of the floor mat peels off. Poor adhesion of the Velcro patch Thank you for all the PuMA ""Info Only"" cases. From these cases, it has been determined that the Velcro peeling fault occurs on mats produced prior to May 2014. We no longer need ""Info Only"" cases from this time period."
NHTSA source summary · Original PDF not reviewed by Recallfolio
Fault Code 1D2008 Stored in DME. The Service Engine Soon light is on. Fault Code 1D2008: Map thermostat: jammed open is stored in the DME. There may also be a complaint of low heat output with lower outside temperatures. CAUSE During the engine warm-up, the engine coolant does not reach operating temperature within the DME's allowable time limits. This is caused by either a faulty thermostat inside the transmission oil heat exchanger or a faulty engine characteristic map thermostat.
Source components: ENGINE · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SI B11 22 14March 2015 EngineTechnical Service This Service Information bulletin supersedes SI 11 22 14 dated February 2015. PERFORM THE PROCEDURE OUTLINED IN THIS SERVICE INFORMATION ON ALL AFFECTED VEHICLES BEFORE CUSTOMER DELIVERY OR THE NEXT TIME THEY ARE IN THE SHOP FOR MAINTENANCE OR REPAIRS. designates changes to this revision SUBJECT Service Action: Replace the Thermostat. The Service Engine Soon light is on with corresponding fault codes in the DME for the engine thermostat. CAUSE Moisture and corrosion could develop on the electrical contacts for the heater circuit in the thermostat.
NHTSA source summary · Original PDF not reviewed by Recallfolio
N20 and N26 Engine: Oil Leaks from Cylinder Head Cover. There is an engine oil leakage under the vehicle, or the vehicle smells of engine oil. The cylinder head cover gasket is leaking engine oil due to loose retaining bolt(s).
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Airbag Warning Light: ACSM FC 930A60 or 930A1C Seat Occupancy Detection. According to the customer, the airbag warning light was on, but it may not be on when the vehicle arrives in the workshop. 1. ACSM fault code ""930A60 - Seat occupancy detection, front passenger; malfunction"" is stored. The fault may or may not currently be present. Or 2. ACSM fault code ""930A1C - Seat occupancy detection, front passenger; malfunction"" is stored. The fault may or may not currently be present. CAUSE The front passenger seat occupancy mat consists of a seat occupancy mat with a capacitive sensor system. This means a front passenger is detected by measuring the resistance of the human body. The fault is set when moisture is detected on the mat itself."
NHTSA source summary · Original PDF not reviewed by Recallfolio
Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15°F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored. When the outside temperatures drop below 46°F, the charging system is switch to full charge. CAUSE ? The check control message (ID 229) is caused by a heavily discharged battery. ? The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). ? In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. ? Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. ? The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting down certain electrical consumers.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SI B12 21 14February 2015 Engine Electrical SystemsTechnical Service This Service Information bulletin supersedes SI B12 21 14 dated December 2014. designates changes to this revision SUBJECT Engine Malfunction Warning Illuminated with FC 193208: Fuel Level Plausibility Stored in DME. The customer states that the engine malfunction warning lamp is illuminated, and while filling the fuel tank, the fuel gauge did not show the proper fill level. After the vehicle is driven a short distance, the fuel gauge will update to full. When diagnosed, the following fault is stored in the DME: z FC 193208 Fuel level, plausibility: deviation between consumption and level change Please proceed to the Procedure section. Vehicles with option 610 (Head-Up Display) are not affected. Please follow the ISTA/D test plan for the applicable faults stored in the DME, including the one listed in this bulletin. CAUSE A software error in the instrument cluster causes the fuel gauge to incorrectly update while refilling. The error occurs when the vehicle is powered up after refilling.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SI B11 22 14February 2015 EngineTechnical Service This Service Information bulletin supersedes SI 11 22 14 dated January 2015. PERFORM THE PROCEDURE OUTLINED IN THIS SERVICE INFORMATION ON ALL AFFECTED VEHICLES BEFORE CUSTOMER DELIVERY OR THE NEXT TIME THEY ARE IN THE SHOP FOR MAINTENANCE OR REPAIRS. designates changes to this revision SUBJECT Service Action: Replace the Thermostat. The Service Engine Soon light is on with corresponding fault codes in the DME for the engine thermostat. CAUSE Moisture and corrosion could develop on the electrical contacts for the heater circuit in the thermostat.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Service Information bulletin supersedes SI B65 24 13 dated January 2014. designates changes to this revision SUBJECT Headunit-High: INITIAL Enabling Code Is Not Accepted Via I-Drive. INFORMATION Do not replace parts and do not program the vehicle for this issue. First-time activation of the navigation system should always be performed during the Quality Certification 1 (QC1) Pre-Delivery Inspection (PDI), with the vehicle connected to the ISTA diagnosis system. Refer to SI B65 22 14. WARRANTY INFORMATION Not applicable since the first time activation of the navigation system is part of the QC1 process and cannot be claimed separately. [ Copyright (c)2015 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/20588.1.B652413....3/2/2015
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Service Information bulletin supersedes SI B65 13 12 dated September 2012. designates changes to this revision SUBJECT Headunit High: Navigation System Road Map Usage. INFORMATION The Headunit High (HU-H), also called NBT, began replacing the Car Information Computer (CIC) on certain MY2013 vehicles with option 609. This change will affect the navigation system road map data support process and the warranty spare parts processes for the HU-H. For the US market, all vehicles will come pre-loaded from the factory with the latest navigation system road map database version that was available at the time of vehicle production. Therefore, there will be no physical copy of the navigation system road map data media DVD set or USB stick placed in these vehicles at the Vehicle Distribution Center (VDC). NOTE: Additionally, all replacement HU-H parts come with a pre-loaded version of the current available navigation system road map database installed. A set of DVD copies of the navigation system road map database, HU-H NAVI Road Map North America NEXT, is shipped to all BMW centers through the automatic tool shipment program with each release of a navigation system road map database. IMPORTANT: Additional copies or earlier NAV road map database versions cannot be ordered individually! Therefore, please take special care to archive the HU-H NAV road map DVD sets! The NAV road map data on the DVD set can also be installed into the Network Attached Storage (NAS). From there it then can be installed onto the HU-H in the vehicle, using the Integrated Service Technical Application for Programming (ISTA/P). For installation of the navigation system road map data media DVD set onto the Network Attached Storage (NAS), please contact your ISPI NEXT Administrator. In addition to this procedure, it is also possible to download the NAV road map data on the DVD set directly to the hard disc drive (HDD) integrated in the HU-H by inserting the DVDs one by one into the HU-H internal DVD
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Service Information bulletin supersedes SI B65 10 09 dated March 2013. designates changes to this revision SUBJECT CIC head unit: Vehicle Position Is Missing or Incorrect on Navigation Map. The vehicle position is missing or incorrect on the navigation map. The navigation system integrated in the Car Information Computer (CIC) is not calibrated correctly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Service Information bulletin supersedes SI B65 05 09 dated July 2009. designates changes to this revision SUBJECT CIC Headunit: Navigation System Road Map Usage. INFORMATION The Car Information Computer (CIC) began replacing the Car Communication Computer (CCC) on vehicles with option 609 in September of 2008. This change affected the navigation system road map data support process and the warranty spare parts processes for the CIC. For the US market, all vehicles come pre-loaded from the factory with the latest navigation system road map database version that was available at the time of vehicle production. Therefore, no physical copy of the navigation system road map data media DVD set or USB stick is placed in these vehicles at the Vehicle Distribution Center (VDC). NOTE: Additionally, all replacement CIC parts come with a pre-loaded version of the current available navigation system road map database installed. A set of DVD copies of the navigation system road map database, CIC NAVI Road Map North America PREMIUM, is shipped to all BMW centers through the automatic tool shipment program with each release of a navigation system road map database. IMPORTANT: Additional copies or earlier NAV road map database versions cannot be ordered individually! Therefore, please take special care to archive the CIC NAV road map DVD sets! The NAV road map data on the DVD set can also be installed into the Network Attached Storage (NAS). From there, it can then be installed onto the CIC in the vehicle, using the Integrated Service Technical Application for Programming (ISTA/P). For installation of the navigation system road map data media DVD set onto the Network Attached Storage (NAS), please contact your ISPI Next Administrator. In addition to this procedure, it is also possible to download the NAV road map data on the DVD set directly to the hard disc drive (HDD) integrated in the CIC by inserting the DVDs one by one into the CIC internal DVD drive. It will take approxim
NHTSA source summary · Original PDF not reviewed by Recallfolio
"SUBJECT Check Control Message: Parking Light Failed. z A CCM (Check Control Message) displays ""Parking Light failed."" z All lights are functioning correctly. Software error in the TMS (Driver Module for Headlight)"
NHTSA source summary · Original PDF not reviewed by Recallfolio
"SUBJECT Ticking Noise from Front Axle When Cornering. Covered under the terms of the BMW New Vehicle/SAV Limited Warranty. Defect Code:34 11 00 57 00Labor Operation:Labor Allowance:Description:34 11 220Refer to KSDRemoving and installing both front brake discsAnd:34 99 0002 FRUWork time for sanding hub surface of brake discs and cleaning wheel hub surfacesLabor operation code 34 11 220 is a Main labor operation. If you are using a Main labor code for another repair, use the Plus code labor operation 34 11 609 instead. With the front brake calipers removed, use 34 11 612, or with the front brake pads removed, use 34 11 613. Refer to KSD2 for the corresponding flat rate unit (FRU) allowance. Enter the Chassis Number, which consists of the last 7 digits of the Vehicle Identification Number (VIN). Click on the ""Search"" button, and then enter the applicable flat rate labor operation in the FR code field. Even though work time labor operation code 34 99 000 ends in ""000"", it is not considered a Main labor operation. Also, since the ""work time"" FRU allowance to be claimed is specified, a separate punch time is not required."
Source components: SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC · WHEELS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUBJECT N20, N26, and N55 Engines with Injector Electrical Faults. Any of the following symptoms could occur simultaneously with injector electrical faults stored in the DME: z After the engine is turned off for a short time, it can no longer be started; however, the starter motor turns. z The engine starts but immediately cuts off. z The engine runs erratically or lacks power. z The Service Engine Soon light (MIL) may be on with several poetential faults stored. The DME has malfunctioned due to an internal fault.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"SUBJECT N55: Slight Surging at Constant Speeds when Accelerating Very Lightly. The vehicle shudders or surges slightly while driving at constant speeds and applying the accelerator very lightly. This symptom is most easily reproduced under light loads when the current fuel consumption is approximately 3448 miles per gallon. The current fuel consumption can selected and monitored in the instrument cluster while driving (the ""fuel consumption, current"" option is set to active in the settings menu). No relevant fault will be stored in the DME memory. DME software; the fuel injection rate under these conditions is too close to the minimum calculated threshold."
Source components: VEHICLE SPEED CONTROL · VEHICLE SPEED CONTROL:ACCELERATOR PEDAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUBJECT DME Internal and Valvetronic Faults Set at Cold Ambient Temperatures. The Service Engine Soon light (MIL) can be illuminated with the erroneous internal and Valvetronic faults stored in the DME. The MIL will only come on if the fault has been detected on two (or more) consecutive drive cycles. The following fault codes may be stored in the DME: E Seriesz 36AE - DME, internal fault, Valvetronic: Current implausible One or more of the following secondary faults may also be stored: z 2DE2 - Valvetronic, actuation, voltage phase: Line disconnection z 2DE3 - Valvetronic, actuation, volt phase: Line disconnection z 2DE4 - Valvetronic, actuation, volt phase: Line disconnection F Seriesz 1F0905 - DME, internal fault, Valvetronic: Current implausible One or more of the following secondary faults may also be stored: z 135B10 - Valvetronic, actuation, voltage phase: Line disconnection z 135B11 - Valvetronic, actuation, volt phase: Line disconnection z 135B12 - Valvetronic, actuation, volt phase: Line disconnection Engine performance and driving characteristics are not affected. DME software diagnostic sensitivity.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUBJECT N20 and N26 Differential Pressure Sensor Fault 195002 Stored in DME. The Service Engine Soon (MIL) light is on with the following differential pressure sensor fault stored: z 195002 - Differential pressure sensor, tank vent valve, electrical: Short circuit to ground During engine operation, vibration and movement of the sensor can damage the pin contacts of the harness connector, or cause a break in the wiring.