2016 BMW 328I Manufacturer communications & TSBs.Page 3
Original record summaries, dates and identifiers for this model-year. Records 201–300 of 387, ordered newest first. Dated records on this page: Feb 1, 2016–Mar 1, 2017.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Mar 1, 2017Service Bulletin/Repair Instructions
B130315
NHTSA communication ID: 10146573
NHTSA source summary · Original PDF not reviewed by Recallfolio
N20, N26, N55, N63TU, S63TU and S55 Engines: Bosch Injector ETK Part Number Error What's New: ? Procedure change: indentifying injector type using an ISTA test plan. . The current version of the ETK incorporates multiple part number errors for the Bosch type injectors. Ordering the injectors by VIN number or manual identification in ETK may result in an incorrect part number.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE ENGINE SOON LIGHT IS ON WITH PT-CAN FAULTS STORED . The Service engine soon light (MIL) is on and the transmission may go into failsafe. The problem may be intermittent along with any of the following check control messages displayed or stored. Transmission temperature Drivetrain fault Chassis stabilization Note: Any combination of the following faults can be stored. DME faults: CDBB04: No message (request, torque, crankshaft, transmission 2), receiver DME, transmitter EGS CDBE04: No message (display, engine speed, dynamic), receiver DME, transmitter EGS CDBF04: No message (status, transmission control unit), receiver DME, transmitter EGS CDC004: No message (diagnosis, OBD gearbox), receiver DME, transmitter EGS CDC104: No message (data, transmission train), receiver DME, transmitter EGS CDC201: No message (request, torque, crankshaft, EGS), receiver DME, transmitter EGS EGS faults: 4209A4: Temperature sensor system: Hotmode 3 - excess temperature CF1501: No message (diagnosis OBD engine), receiver EGS, transmitter DME/DDE CF1521: Message (group fault 1 - effect during driving: considerable): Receiver EGS, transmitter DME/DDE CF1531: Message (group fault 2 - effect on driving: possible): Receiver EGS, transmitter DME/DDE CF1541: Message (group fault 3 - effect on driving: none): Receiver EGS, transmitter DME/DDE CF2C21: Signal (actual engine speed, crankshaft - signals a poor quality useful signal, 0xA5) undefined, transmitter DME/DDE The EGS harness wiring from connector X13*2B becomes damaged due to abrasive movement inside the corrugated housing.
NHTSA source summary · Original PDF not reviewed by Recallfolio
?VOLUNTARY EMISSIONS RECALL CAMPAIGN 16E-A05 - N26 ENGINE: REPLACE TURBOCHARGER OIL SUPPLY LINE What's New: ? Labor allowance adjusted for xDrive vehicles . Carbonization of the turbocharger sealing ring can cause the exhaust to smoke briefly during cold start up.
NHTSA source summary · Original PDF not reviewed by Recallfolio
?Service Action: Replace the Thermostat What's New: ? Part number and quantity of coolant has been updated. Refer to the Warranty section for details. . The Service Engine Soon light is on with corresponding fault codes in the DME for the engine thermostat.
NHTSA source summary · Original PDF not reviewed by Recallfolio
HEADUNIT NAVIGATION MAPS (HU-H HU-H2 HU-B): The Headunit High (HU-H), also called NBT, began replacing the Car Information Computer (CIC) on certain MY2013 vehicles with option 609 (7/2012+).
NHTSA source summary · Original PDF not reviewed by Recallfolio
?Various Check Control Messages Caused by Shorted K- CAN This Service Information bulletin supersedes SI B61 03 15 dated June 2016. . The customer states that one or more of the following CC messages are displayed: 627 - Steering behavior: Drive moderately 070 - Steering: Drive moderately 765 - Rear-end collision restricted 850 - Pedestrian warning restricted 236 - Driving stabilization: Drive moderately 299 - SOS call system failure 042 - Brake system: Drive moderately After performing a vehicle test, one or more of the following fault codes are stored: ACSM - C9549A Message faulty (seat memory), ACSM receiver, driver's seat module transmitter FEM - D91DE0 No message, receiver FEM, transmitter TMSL FEM - D91EE5 No message, receiver FEM, passenger seat module transmitter ACSM - C9540C Message missing, receiver ACSM, transmitter FEM TMSL - D95402 Message missing, receiver TMSL, transmitter FEM KOMBI - E11454 No message, receiver KOMBI, transmitter REM FEM - D91DE6 No message, receiver FEM, transmitter TMSL TMSR - D99401 Message missing, receiver TMSR, transmitter FEM TMSR - D99402 Message missing, receiver TMSR, transmitter FEM FEM - 8041BA AHL system faulty FEM - D916C3 No message, receiver FEM, transmitter TCB ZBE - E2D403 No message, receiver CON, transmitter FEM-ZGM TRSVC - CA9428 Message incorrect, receiver TRSVC, transmitter PDC-REM TMSL- D95401 Message missing, receiver TMSR, transmitter FEM HU-H - S0397 MOST configuration was not stored TCB - E1445F KCAN2 or KCAN4: Line fault/electrical fault FEM - 8041B6 LWR faulty REM - E58468 Body CAN2; communication fault TRSVC - CA9427 Message incorrect, receiver all around vision camera, transmitter PDC/REM FEM - D91CEC Message missing, receiver FEM, transmitter REM Shorted K-CAN wiring under driver or passenger seat Shorted K-CAN2 wires were shorted between the left side trunk trim panel and the body of the vehicle Shorted K-CAN in left rear wheel well area Shorted K-CAN under center console trim Shorted K-CAN und
NHTSA source summary · Original PDF not reviewed by Recallfolio
?MISSING AUDIO NOTIFICATION WHEN STORING SEAT MEMORY . When saving seat memory settings (Memory 1 or Memory 2) with a vehicle without navigation, there is no audio tone confirmation. Software error in control unit of Seat Module 2.
NHTSA source summary · Original PDF not reviewed by Recallfolio
?RATTLING/CREAKING NOISE FROM REAR BENCH SEAT BACKREST . Rear seat bench backrest makes creaking or rattling noise when driving on uneven surface. Torsional stresses on vehicle body cause movement between seat back and latching mechanism. Friction among backrest locking mechanism components generates noise.
NHTSA source summary · Original PDF not reviewed by Recallfolio
?FRONT SUSPENSION RIDE HEIGHT HAS DROPPED . INFORMATION Please refer to the Electronic Parts Catalog (EPC), using the VIN to locate the part numbers. WARRANTY INFORMATION Damages due to outside influences are not covered under the terms of the BMW limited warranties.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"? NO REGENERATION OF THE DIESEL PARTICULATE FILTER (DPF) This Service Information bulletin supersedes SI B18 03 10 dated November 2010. . The Service Engine Soon lamp is illuminated. The following fault codes may be stored in the DDE: N47T/N57T engine 245700 - Particle filter system: particulate filter highly loaded (Exhaust backpressure high) 245800 - particle filter system - filter is heavily contaminated. (exhaust backpressure is above maximum) M57Y engine 480A Particle filter system - filter is heavily contaminated. (exhaust backpressure is too high) 481A Particle filter system - filter is heavily contaminated. (exhaust backpressure is above maximum) CAUSE 1. Faults with the exhaust system that affect the monitoring of the DPF by the DDE 2. Unfavorable recent driving profile INFORMATIOM During normal driving, there is a continuous regeneration of the diesel particulate filter that takes place at exhaust-gas temperatures between 280 and 350°C (slower oxidation process). The soot particles can only be burned off when the required exhaust-gas temperature has been reached. Under certain driving conditions (i.e., prolonged short trips or an exhaust system which never reaches soot burn-off temperatures), the DPF can become restricted. The DDE will initiate periodic regeneration automatically, at the latest after 600 miles. In vehicles making many short distance journeys, periodic regeneration takes place after only 250-500 miles. The Digital Diesel Electronics control unit evaluates the time for periodic regeneration from the following values: average distance driven average driving speed temperature in the diesel particulate filter values from the exhaust pressure sensor The DDE initiates the regeneration process by decreasing incoming air by the throttle valve, and one or two post injections are executed. This heats the exhaust-gas temperature to approx. 600° C . When the exhaust temp reaches this point: The soot is burned off with the residual oxygen. The
Source components: ENGINE · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"? DIESEL PARTICULATE FILTER (DPF) CLEANING . The following performance issues may be noticed by the customer: CC-Message ""Drive faulty"" Engine jerking or a lack of power over the whole engine speed range Malfunction indicator lamp (MIL) is illuminated The following fault codes may be stored in the DDE: N47T/N57T engine Main Faults: 245700 - Particle filter system: particulate filter highly loaded (Exhaust backpressure high) 258300 - Exhaust backpressure sensor, Signal: Signal too high Secondary Faults: 244C00 - Charging pressure control, control deviation: charging pressure too low/positive deviation 25DA00 - Exhaust gas difference pressure sensor particle filter, Signal: short circuit to plus pole M57Y engine Main Faults: 480A particle filter system 481A particle filter system Secondary Faults: 4530 charging pressure control, control deviation 429A charging pressure control low pressure stage, control deviation Clogged DPF."
Source components: ENGINE · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
?VOLUNTARY EMISSIONS RECALL CAMPAIGN 16E-A05 - N26 ENGINE: REPLACE TURBOCHARGER OIL SUPPLY LINE . Carbonization of the turbocharger sealing ring can cause the exhaust to smoke briefly during cold start up.
Source components: ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
During opening and closing of the tailgate, a creaking noise can be heard from the tailgate lock. Excess friction caused by dust/dirt entry into the tailgate lock and on the striker.
NHTSA source summary · Original PDF not reviewed by Recallfolio
?WHEEL COVER PILOT PROGRAM. BMW is piloting/testing a measure that is designed to help prevent brake disc/rotor surface corrosion on new vehicles during transportation and storage.
Source components: SERVICE BRAKES, AIR:DISC · SERVICE BRAKES, AIR:DISC:ROTOR · SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC · SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC:ROTOR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
?SERVICE ACTION: REPLACE LOW-PRESSURE ELECTRIC IN-TANK FUEL Please perform the procedure outlined in this Service Information on all affected vehicles before customer delivery or the next time the vehicle is in the shop.
NHTSA source summary · Original PDF not reviewed by Recallfolio
?Service Action: Replace the Thermostat. Please perform the procedure outlined in this Service Information on all affected vehicles before customer delivery. In the event the customer has already taken delivery of the vehicle, please perform the procedure the next time the vehicle is in the shop. This Service Information bulletin supersedes SI B11 10 15 dated January 2016.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SI B65 09 15 November 2016 Audio, Navigation, Monitors, Alarms,SRS Technical Service NBT Head Unit High (HU-H) Resets Intermittently or Permanently. The Head Unit-High (HU-H) resets intermittently or permanently. 1. The display is inoperative and there is no audio output 2. Automatic system start-up after a couple of seconds Fault Code E1C440 set No Fault Codes set Software error in the Head Unit High (HU-H)
NHTSA source summary · Original PDF not reviewed by Recallfolio
TURN SIGNAL - INTERMITTENTLY FLASHES AT FASTER RATE. Turn signal, intermittently, flashes at faster rate or not at all. Software error in FEM (Front Electronics Module)
Source components: ELECTRICAL SYSTEM · EXTERIOR LIGHTING:TURN SIGNAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
LANE CHANGE WARNING: FALSE ACTIVATION. Lane Change Warning (LCW) system issues warnings when no other vehicle is present: illuminates lane change warning indicator on the exterior mirrors vibrates steering wheel Lane change sensor software
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · LANE DEPARTURE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"USB DEVICE IS NOT DETECTED BY CHAMP2 HEAD UNIT. Media connected to the USB connector is not recognized by the audio system. Playback of files from the media is not possible. Message displayed on the audio system display: ""Title cannot be reproduced"" ""Is being read"" (but never plays back any audio) CAUSE Media with data files stored in more than 32 directories or 32 subdirectories within a directory. Media with a large number of files. Media exceeds total storage capacity of 32 GB."
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"NBT-EVO Head Unit Cannot Be Swapped Between Vehicles for Testing This Service Information bulletin supersedes SI B65 13 16 dated July 2016.. If an NBT-EVO head unit is swapped into a different vehicle it will enter a locked mode once it recognizes a different VIN. This will set a fault in the Head Unit (NBT-EVO), Fault Code ""B7F87A: Burgler Actively Registered / Component Protection Active"" This will require REPLACEMENT of the head unit to restore operation. To prevent easy re-use of stolen Head units additional features are introduced with 11/15 ISTA/P software to bring NBT-EVO to a higher security level. In NBT-EVO the mechanism is called ""Trusted VIN"""
NHTSA source summary · Original PDF not reviewed by Recallfolio
"HEADLIGHT ASSEMBLIES HAVE VISIBLE INTERNAL MOISTURE/CONDENSATION. Water on the inside (A) or misting (B) of both headlight lenses that is visible from outside. Water inside the headlights can be caused by two situations: Water/moisture ingress into the headlight housing. Thermal conditions that result in the formation of condensation. Note: An important indication that the moisture issue is caused by ""condensation"" rather than a ""water leak"" into the headlight housing, there will be misting/condensation in ""both headlights."""
NHTSA source summary · Original PDF not reviewed by Recallfolio
WATER DRIPPING INTO LUGGAGE COMPARTMENT FROM OPEN TRUNK LID. Water drips into luggage compartment when the trunk lid is lifted (also see attached video below). www.tinyurl.com/F30trunk trunk lid making sure it flows over the taillight. Open the trunk lid within one minute of pouring water over taillight. Water trapped between the tail light module and the body of the vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
8HP: TRANSMISSION FLUID LOSS FROM COOLER LINES CONNECTIONS. There is a transmission fluid leak in the area around the oil cooler lines (on the transmission side). CAUSE Damaged O-rings due to unfavorable cooling line connection tolerances
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
VOLUNTARY EMISSIONS RECALL CAMPAIGN 16E-A05 - N26 ENGINE: REPLACE TURBOCHARGER OIL SUPPLY LINE. Carbonization of the turbocharger sealing ring can cause the exhaust to smoke briefly during cold start up.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits This Service Information bulletin supersedes SI B07 03 14 dated October 2015.. Fault codes stored in vehicles being serviced are not being diagnosed, leading to repeat repair visits (source- Analysis of FASTA data and repeat repair visit reports). INFORMATION Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) to find their root cause during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"NBT NAVIGATION DOES NOT ROUTE ON TOLL ROADS. NBT Navigation does not provide routes that include certain toll roads. CAUSE Roads that have toll lanes ""without a cash option"" where not utilized for routing in NBT map data versions: NEXT 2015-1 NEXT 2015-2 NEXT 2016-1 As an enhancement, the NEXT 2017-1 map release now provides information about toll lanes ""without cash option"". UPDATE Install new map data."
NHTSA source summary · Original PDF not reviewed by Recallfolio
?AUDIO VOLUME NOT RESTORED AFTER MSA STOP, ENTRY HEAD UNIT. Volume of audio system (when set to near maximum) is reduced when Auto Start-Stop (MSA) stop occurs and is not restored upon automatic engine restart. This is normal system behavior - serves to protect the head unit, battery drain and avoidance of incremental leaps in the loudness. The loudness is reduced to 2/3 of maximum and is not restored. Note: Air conditioning output is also reduced upon MSA stop and is not restored for similar reasons.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE ACTION: LEFT SIDE DOORS MAY NOT OPEN FROM OUTSIDE. Left side doors (front and/or rear) may not be able to be opened from the outside. Bowden cable may twist and come loose from the bracket on the outside door handle support.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE ACTION: CHECK RIGHT SIDE REAR DOOR FOR WATER LEAK TIGHTNESS. The sound insulation on the right side rear door may not have been bonded properly. The right rear door sound insulation may not have been applied correctly and can cause water leaks.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CBS BRAKE PAD CALCULATION AND CORRECTION. When a vehicle comes into the workshop for any repair or maintenance job, the bundling calculator recommends a brake maintenance checkup. No brake warning light is illuminated. CBS shows 3,107 miles or slightly higher for the next brake service displayed via Key Reader, or vehicle's Control Display (in Vehicle Info/Status/Service required/Brake pads) CAUSE CBS calculates the remaining brake pad wear based on brake pressure, speed, vehicle specific parameters (i.e. NAO pads), brake temperature as well as cumulative brake application time. Due to variation of these parameters and outside environmental influences, this calculation can deviate from the real brake pad wear. Starting from the above-mentioned production dates of the vehicles indicated, the CBS brake pad wear calculation has been changed, and is now based only on the brake pad wear sensor. Important Note: To avoid a too-slow wear prediction, the CBS brake model will estimate the need for repairs, in some cases, rather early. Calculation will level at 3,107 miles and stay at this value until the CBS brake pad wear sensor is triggered. https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/36...11/8/2016 Page 2 of 2 After the sensor is triggered, the CBS mileage will count down indicating to the customer that the brake repairs will be due.
NHTSA source summary · Original PDF not reviewed by Recallfolio
VOLUNTARY EMISSIONS RECALL CAMPAIGN 16E-A05 - N26 ENGINE: REPLACE TURBOCHARGER OIL SUPPLY LINE. Carbonization of the turbocharger sealing ring can cause the exhaust to smoke briefly during cold start up.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"SERVICE ACTION: SUPPLEMENTARY PAGE NEEDED IN OWNER'S MANUAL. Operator's manual of affected vehicles does not contain required information on wireless smartphone charging accessory. AFFECTED VEHICLE Vehicles which require this Service Action to be completed will show it as ""Open"" when checked either in the ""Service Menu"" of DCSnet (Dealer Communication System) or with the Key Reader."
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOS MALFUNCTION DISPLAYED. An SOS malfunction is seen in the Kombi. When pressing the E-Call/SOS button in the overhead console, nothing happens. Fault code B7F33C (internal ECU error) is stored in the Telematics control unit (ATM/TCB2). There are 2 known causes for this failure. They are as follows: Software file missing from the ATM/TCB2 control module Water leak at shark-fin leading to corrosion in the ATM/TCB2 control module
NHTSA source summary · Original PDF not reviewed by Recallfolio
"HVAC BLOWER NOT WORKING This Service Information bulletin supersedes SI B64 12 16 dated August 2016. HVAC blower is not working. Condensation occurs even though blower is working. CC message ""Increased battery discharge"" - standby current violation may be displayed. Climate control unit (IHKA) software"
NHTSA source summary · Original PDF not reviewed by Recallfolio
REWORKING THE PVC SEAM SEAL ON THE RIGHT REAR WHEEL ARCH. PVC Seam Sealer on the right rear inner wheel arch may not have been properly applied. Ineffective manufacturing procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CREAKING NOISES FROM DOOR TRIM PANEL. Creaking noise is heard from door trim panel while driving on rough roads. Door trim panel is contacting the inner door panel.
NHTSA source summary · Original PDF not reviewed by Recallfolio
HOOD GAS-FILLED SHOCK ABSORBER MOUNT IS BROKEN. Hood gas filled shock absorber is loose or broken, the hood does not remain in the opened position. Gas filled shock absorber mounting point has broken free from the body.
NHTSA source summary · Original PDF not reviewed by Recallfolio
BMW ONLINE NON-FUNCTIONAL: CHECK ICC-ID IN ACCOUNT. The ConnectedDrive Services are non-functional after a hardware exchange of the telematics control unit. This is not indicated by CC-message. ConnectedDrive Services not synchronized by Telematics Control Unit.
NHTSA source summary · Original PDF not reviewed by Recallfolio
INFORMATION ON THE OPERATION OF THE SMART OPENER. INFORMATION ON THE OPERATION OF THE SMART OPENER MODEL F07 (5 Series Gran Turismo) F10 (5 Series) F12 (6 Series Convertible) F13 (6 Series Coupe) F15 (X5) F16 (X6) F22 (2 Series Coupe) F23 ( 2 Series Convertible) F25 (X3) F26 (X4) F30 (3 Series Sedan) F31 (3 Series Wagon) F32 (4 Series Coupe) F33 (4 Series Convertible) F34 (3 Series Gran Turismo) F36 (4 Series Gran Coupe) F48 (X1) F80 (M3 Sedan) F82 (M4 Coupe) F83 (M4 Convertible) F85 (X5 M) F86 (X6 M) G12 (7 Series) I01 (i3 Series) Vehicles with option code SA-0322 (Comfort Access) without M-Sport trim INFORMATION The smart opener (Contactless tailgate) operates as described below: Ignition key must be within 3 feet behind the vehicle, clear from any interference like a smartphone The customer must be at least an arms-length behind the vehicle Kick your foot forwards & backwards under the vehicle in one quick movement The taillights flash confirming that the trunk will open The trunk then successfully opens For more information an instructional video can be viewed which demonstrates the operation. Thanks to BMW of Tenafly for providing the video. tinyurl.com/Autotrunk1 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/358...9/3/2016 Page 2 of 2 WARRANTY INFORMATION Not applicable. [ Copyright (c)2016 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/358...9/3/2016
NHTSA source summary · Original PDF not reviewed by Recallfolio
"HVAC BLOWER NOT WORKING. HVAC blower is not working. Condensation occurs even though blower is working. CC message ""Increased battery discharge"" - standby current violation may be displayed. Climate control unit (IHKA) software"
NHTSA source summary · Original PDF not reviewed by Recallfolio
TAILGATE UNINTENTIONALLY OPENS. Trunk/tailgate may open when vehicle is locked. Trunk/tailgate may open while the vehicle is in motion. Usually after stopping, such as a traffic light etc. Vehicle key trunk/tailgate button may accidentally be pressed, thus opening the tailgate.
NHTSA source summary · Original PDF not reviewed by Recallfolio
INTERMITTENT DISTORTION IN AUDIO SYSTEM, DRIVER'S SIDE. Distortion in audio system from subwoofer on driver's side. Rodent ingress into subwoofer enclosure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Delivery Stop: Remove Engine Oil Label. Affected vehicles in dealer inventory must not be retailed or delivered until the label is removed. Vehicles at ports of entry will be remedied prior to dealer delivery. On affected vehicles, there is an incorrect label regarding the appropriate engine oil. Affected vehicles can be identified with a ""Vehicle Comment"" in the DCS Warranty Vehicle Inquiry or ISPA Light. https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/248...9/3/2016 Page 2 of 2"
NHTSA source summary · Original PDF not reviewed by Recallfolio
"DSC ""WHEEL SPEED SENSOR"" FAULT CODES AND MALFUNCTION INDICATOR LAMP- DIAGNOSTIC. 1. DSC's fault codes stored from two different wheel speed sensors (both front or both rear): 4809B0 - wheel speed sensor - front left - drive off recognition faulty and 4809CD - wheel speed sensor - front right - drive off recognition faultyor 4809B9 - wheel speed sensor - rear left - drive off recognition faulty and 480686 - wheel speed sensor - rear right - drive off recognition faulty. 2. Next ignition ON (after above codes stored). a) DME fault can occur:1F054D - drive, safety function: Drive power output reduced, DSC signals implausible and b) Malfunction Indicator Lamp (MIL) may light up. Faulty drive off recognition due to: a towing operation with a raised axle operation of the vehicle on the vehicle hoist operation of the vehicle on the roller test stand DSC diagnosis recognizes implausible wheel speeds, so no control is possible. DME fault is entered on safety grounds since the DSC fault still exists after a terminal change and may only be removed while driving."
Source components: SERVICE BRAKES, AIR:ANTILOCK:WHEEL SPEED SENSOR · SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP:WHEEL SPEED SENSOR/TONE RING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"KLE CHARGING FAULT 21E6E9. During the ISTA short test diagnosis, fault code 21E6E9 - ""Charging interruption"" is found stored in the KLE (Convenience Charging Electronics) module. There is no customer complaint related to charging system, or a warning check control message display. CAUSE An Erroneous fault 21E6E9 stored in the KLE after completion of AC charging session."
NHTSA source summary · Original PDF not reviewed by Recallfolio
Rattle Or Buzzing Noise At 1500 To 2200 Rpm. When accelerating, particularly when driving off on a slope, there is a buzzing, rattling noise coming from the driver's side underbody, near the footwell area. The quick-release coupling for the fuel line is contacting the fuel line protective plate.
NHTSA source summary · Original PDF not reviewed by Recallfolio
N20 - The Service Engine Soon Light is On with DME Fault 118602 Stored. The Service Engine Soon light is on (MIL) with only the following oxygen sensor fault stored. 118602 - Oxygen sensor before catalytic converter, fine mixture control: exhaust gas after catalytic converter too lean CAUSE An actual engine related problem and/or DME software diagnostic.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"CCM - ""COOLANT LEVEL LOW"". Sporadically, while driving in ePower mode, a ""Coolant Low"" Check Control Message appears, even though coolant is at the specified level. FEM (Front Electronic Module) Control unit software error"
Source components: ENGINE · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Center Information Display Switching off. INFORMATION The brightness of the CID will reduce and may switch off completely due to high temperature rise inside the vehicle. This situation is to protect the function of the CID. After lowering the temperature, the normal functions are restored. The increased temperature, protective switch-off is the reason for the fault. The fault code does not indicate a defective head unit. The normal maximum temperature operation for the head unit is between 167 and 194 F. Within these values, the CID will gradually diminish in brightness until it completely switches off. Replacing parts or programing the vehicle will not rectify the situation. The root cause is the very high temperature and is not a fault of the vehicle's systems.
NHTSA source summary · Original PDF not reviewed by Recallfolio
HeadUp Display does not Show Full Street Names. INFORMATION Design of the HUD has limited display area. (It can only show a certain number of text characters). NOTE: Parts replacement or programming the vehicle will not recitify the situation!
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various Check Control Messages Caused by Shorted K-CAN This Service Information bulletin supersedes SI B61 03 15 dated April 2016. The customer states that one or more of the following CC messages are displayed: 627 - Steering behavior:Drive moderately 070 - Steering: Drive moderately 765 - Rear-end collision restricted 850 - Pedestrian warning restricted 236 - Driving stabilization: Drive moderately 299 - SOS call system failure 042 - Brake system: Drive moderately After performing a vehicle test, one or more of the following fault codes are stored: ACSM - C9549A Message faulty (seat memory), ACSM receiver, driver's seat module transmitter FEM - D91DE0 No message, receiver FEM, transmitter TMSL FEM - D91EE5 No message, receiver FEM, passenger seat module transmitter ACSM - C9540C Message missing, receiver ACSM, transmitter FEM TMSL - D95402 Message missing, receiver TMSL, transmitter FEM KOMBI - E11454 No message, receiver KOMBI, transmitter REM FEM - D91DE6 No message, receiver FEM, transmitter TMSL TMSR - D99401 Message missing, receiver TMSR, transmitter FEM TMSR - D99402 Message missing, receiver TMSR, transmitter FEM FEM - 8041BA AHL system faulty FEM - D916C3 No message, receiver FEM, transmitter TCB ZBE - E2D403 No message, receiver CON, transmitter FEM-ZGM TRSVC - CA9428 Message incorrect, receiver TRSVC, transmitter PDC-REM TMSL- D95401 Message missing, receiver TMSR, transmitter FEM HU-H - S0397 MOST configuration was not stored TCB - E1445F KCAN2 or KCAN4: Line fault/electrical fault FEM - 8041B6 LWR faulty REM - E58468 Body CAN2; communication fault TRSVC - CA9427 Message incorrect, receiver all around vision camera, transmitter PDC/REM FEM - D91CEC Message missing, receiver FEM, transmitter REM Shorted K-CAN wiring under driver or passenger seat Shorted K-CAN2 wires were shorted between the left side trunk trim panel and the body of the vehicle Shorted K-CAN in left rear wheel well area Shorted K-CAN under center console trim Shorted K-CAN under A-Pill
NHTSA source summary · Original PDF not reviewed by Recallfolio
RATTLE OR SCRAPING NOISE IN ROOF LINER. A scraping or groaning noise can be heard from the left or right side of the headliner from the A, B or C-pillar. The head air bag fabric may rub on the headliner.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Thumping noises from the front section of the vehicle. Thumping noises from the front section of the vehicle may occur when driving over poor road surfaces. Software of the Variable Damper Control (VDC)
NHTSA source summary · Original PDF not reviewed by Recallfolio
Vibration or Knocking Noise from the Center of the Vehicle. When accelerating, there is a knocking, or vibration, felt from the center of the vehicle. This sensation can be easily duplicated when accelerating with the transmission in 2nd or 3rd gear (manual mode). Torque flex in the rear driveshaft.
Source components: POWER TRAIN · POWER TRAIN:DRIVELINE:DRIVESHAFT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Diesel Engine: Intake Manifold Damaged. The Service Engine Soon light is on. There may also be: Complaints of lack of engine performance An exhaust smell coming from the engine area. The following fault codes may be stored in the DDE: 24CE00 - Hot film air mass meter: Ratio of measured to calculated air mass too high 27F000 - Charge air hose monitoring in idle: Charge air hose fallen down 290900 - Air system, air to EGR air mass flow plausibility: Measured air mass compared to calculated air mass too high 290A00 - Air system, air to EGR air mass flow plausibility: measured air mass compared to calculated air mass too high and high charging pressure control deviation 1. Excessive thermal load from the EGR system on the intake components 2. An excessive or unmetered air leak in the intake/charge air system
Source components: ENGINE · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Bluetooth Connection Failures. There are various connectivity failures with the following devices: Apple iPhones Samsung S6 and the S6 Edge. Connectivity failure examples are: Call disconnection - Call is transferred back to the handset. In some instances the call is then transferred back to the vehicle. Contact List incomplete General connection failures Apple iOS software (issue started with iOS 8.3 continues with iOS 9.x and its variants) Samsung S6 and S6 Edge device firmware.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"""Collision Warning Failed"" or ""Pedestrian Warning Failed"" CCM Display. While driving, a Check Control Message (CCM) is displayed advising of the following: Front collision warning failed Pedestrian detection failed The following fault code is stored in the KAFAS (Camera-based Driver Assistance System): 0X800AC4 - Camera calibration failed The KAFAS camera is not properly mounted and secured to the mounting bracket on the windshield; And/ or: The mounting bracket glued to the windshield is not installed correctly. The pictures below show both incorrect and correct installation. This picture shows the KAFAS camera installed in the bracket. Notice the spacing highlighted by the ""green lines"""
NHTSA source summary · Original PDF not reviewed by Recallfolio
SI B51 23 15 Body Equipment May 2016 Technical Service The Driver's Side Front/Rear Door Can No Longer Be Opened from the Outside This Service Information bulletin supersedes SI B51 23 15 dated September 2015.. A driver's-side door cannot be opened by the outside door handle. This concern can also affect the driver's side rear door on the F34 and F36. The Bowden cable has become detached.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Passenger Side Mirror Dimming Feature Operational Change. INFORMATION The automatically dimming exterior mirror function on the passenger's side has been deleted from the Option Code 430 as noted above. The automatic dimming function will continue to be operational on the driver's side mirror and rear view mirror.
NHTSA source summary · Original PDF not reviewed by Recallfolio
F30 PHEVs- Delayed Driving Readiness Status. Immediately after an engine start (start/stop button press), the gear selector is operated, but no drive position (D or R) can be engaged (transmission stays in P). The customer must operate the gear selector again to engage a desired drive position. Unfavorable software application Vehicle requires approximately 1 second after the start/stop button is pressed to establish a Drive Readiness status. If the gear selector is operated during this 1-second window, gear selection is not going to be executed and the gear shifter must be engaged again.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:GEAR POSITION INDICATION (PRNDL).
NHTSA source summary · Original PDF not reviewed by Recallfolio
"F15, F30 PHEVs- Gear Selector Plausibility Faults. The Check Control message ""Drive: Stop carefully"" (CCM-ID: 569) is displayed. The following fault codes may be stored in the transmission EGS control module (GKEG3HY3): 44D663 - Position plausibility: Driver's choice N/P from D/R not executed CF1701 - Gear selector switch interface, communication failure CF17A1 - Message missing: receiver EGS (A-CAN), transmitter selector switch (A-CAN) EGS software diagnostic function"
Source components: POWER TRAIN · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM) · POWER TRAIN:AUTOMATIC TRANSMISSION:GEAR POSITION INDICATION (PRNDL).
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOS Malfunction Is Displayed In Kombi Sporadically. After engine start-up, a CCM (Check Control Message) for SOS malfunction is displayed in the Kombi and in the CID (Central Information Display). One or more of the fault codes below may be stored in the TCB or Combox control unit: 0xB7F32B - GSM Antenna: Open Circuit 0xB7F31F - GSM Antenna: Short to ground 0xB7F31E - GSM Antenna: Open Circuit A signal error is identified during the aerial self-test performed by the TCB (Telematic Control Box or the Combox).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Erroneous Lane Change Warning. While driving, the Lane Change Warning (Blind Spot Detection) is illuminated erroneously on either outside mirror (orange triangle) when no other vehicles are around. CAUSE F30 - Install the correct sensor frame F34 - Program the vehicle using ISTA/P 3.58.0 or higher.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Instrument Cluster Resets during Active Navigation. The instrument cluster (MID KOMBI) fails sporadically (all gauges falling briefly to zero, flashing of all indicator lights) and resets. Reset occurs during active route guidance and predictably when passing certain geographical positions. Software error in navigation head unit
NHTSA source summary · Original PDF not reviewed by Recallfolio
"The Low Washer Fluid Warning Light is illuminated when the Washer Fluid Tank is Full. The low washer fluid warning light is illuminated even though the washer fluid tank is full. There are no faults stored in the system for the washer fluid level switch. CAUSE A non-approved washer fluid is used (fluids that contain a silicone additive, normally colored other than blue). INFORMATION The washer fluid level sensor is a contactless capacitive sensor. The sensor sends a low fluid level signal to the gateway module (FEM - Front Electronics Module or BDC - Body Domain Controller) which in turn displays a low washer fluid warning in the instrument cluster. The use of a ""non-approved"" washer fluid (silicone-based fluid) can cause the low fluid warning light to come on even when the reservoir is full. Refer to ISTA document ""FB-GZ-B17A-F20 Washer fluid level sensor"" for information on how this capacitive sensor operates."
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various Check Control Messages Caused by Shorted K-CAN. The customer states that one or more of the following CC messages are displayed: 627 - Steering behavior: Drive moderately 070 - Steering: Drive moderately 765 - Rear-end collision restricted 850 - Pedestrian warning restricted 236 - Driving stabilization: Drive moderately 299 - SOS call system failure 042 - Brake system: Drive moderately After performing a vehicle test, one or more of the following fault codes are stored: ACSM - C9549A Message faulty (seat memory), ACSM receiver, driver's seat module transmitter FEM - D91DE0 No message, receiver FEM, transmitter TMSL FEM - D91EE5 No message, receiver FEM, passenger seat module transmitter ACSM - C9540C Message missing, receiver ACSM, transmitter FEM TMSL - D95402 Message missing, receiver TMSL, transmitter FEM KOMBI - E11454 No message, receiver KOMBI, transmitter REM FEM - D91DE6 No message, receiver FEM, transmitter TMSL TMSR - D99401 Message missing, receiver TMSR, transmitter FEM TMSR - D99402 Message missing, receiver TMSR, transmitter FEM FEM - 8041BA AHL system faulty FEM - D916C3 No message, receiver FEM, transmitter TCB ZBE - E2D403 No message, receiver CON, transmitter FEM-ZGM TRSVC - CA9428 Message incorrect, receiver TRSVC, transmitter PDC-REM TMSL- D95401 Message missing, receiver TMSR, transmitter FEM HU-H - S0397 MOST configuration was not stored TCB - E1445F KCAN2 or KCAN4: Line fault/electrical fault FEM - 8041B6 LWR faulty REM - E58468 Body CAN2; communication fault TRSVC - CA9427 Message incorrect, receiver all around vision camera, transmitter PDC/REM FEM - D91CEC Message missing, receiver FEM, transmitter REM Shorted K-CAN wiring under driver or passenger seat Shorted K-CAN2 wires were shorted between the left side trunk trim panel and the body of the vehicle Shorted K-CAN in left rear wheel well area Shorted K-CAN under center console trim Shorted K-CAN under A-Pillar trim
NHTSA source summary · Original PDF not reviewed by Recallfolio
Groaning Noise from Doors over Rough Roads. A groaning noise is heard from the doors when driving over rough road surfaces. Window guide rubbing on door opening.
NHTSA source summary · Original PDF not reviewed by Recallfolio
N20 - The Service Engine Soon Light is On with DME Fault 118602 Stored. The Service Engine Soon light is on (MIL) with only the following oxygen sensor fault stored. 118602 - Oxygen sensor before catalytic converter, fine mixture control: exhaust gas after catalytic converter too lean CAUSE An actual engine related problem and/or DME software diagnostic
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
N20 and N26 engine: Smoke from Exhaust when Starting a Cold Engine. When starting a cold engine, blue smoke can be seen emitting from the exhaust tailpipe for approximately 10-20 seconds. No turbo charger boost faults are stored and no drivability issues can be detected. CAUSE When the vehicle is parked overnight the engine oil pressure will equalize and may leak past the turbo charger exhaust side turbine seal.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"During the QC1 the BMW Assist Test Call Fails. After the transport mode is deleted (during the QC1), a BMW Assist (SOS) test call is made by pressing the SOS/ E-Call button. However, the call only connects via voice (no data is transmitted). The operator indicates that a crash call has been sent. ATM fault code ""B7F348 - Provisioning without signature OTA"" is stored. The provisioning of the ATM (Advanced Telematics Module) has failed."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"NBT-EVO Head Unit Cannot Be Swapped Between Vehicles for Testing. If an NBT-EVO head unit is swapped into a different vehicle it will enter a locked mode once it recognizes a different VIN. This will require REPLACEMENT of the head unit to restore operation. To prevent easy re-use of stolen Head units additional features are introduced with 11/15 ISTA/P software to bring NBT-EVO to a higher security level. In NBT-EVO the mechanism is called ""Trusted VIN"""
NHTSA source summary · Original PDF not reviewed by Recallfolio
NBT and Entry Head Unit Software Update for Improved Satellite Radio Reception. Poor Satellite Radio reception CAUSE After this software update there is a slight improvement in Satellite Radio reception for these vehicles when receiving their signal from XM Satellites. This is due to the changeover from Sirius Satellite broadcasting to XM Satellite broadcasting in 2016 (See SI B65 19 15).
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
NHTSA source summary · Original PDF not reviewed by Recallfolio
NBT Head Unit Aborts Import of CD. While importing a CD to the internal music collection of an NBT head unit the process aborts. You will see 'import error' on the radio display when this occurs. NBT Head Unit software
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Air Conditioning Refrigerant R1234yf Introduction. Highlights of R-1234yf Meets SAE J2888_201301 ""This SAE Standard covers fittings, couplers, and hoses intended for connecting service hoses from mobile air- conditioning Systems to service equipment such as charging, recovery and recycling equipment"" New tools and equipment are required. To service vehicles equipped with R-1234yf refer to SI B04 02 16. Air conditioning technician certification is required to work on system. Refer to your State Law. Unique low and high side fittings. Revised evaporator core as per SAE J2842. System will use about 5% more refrigerant than a comparable R134a system. System oil is a specific PAG oil. Refer to ISTA repair recommendation. Do not interchange components between systems using other refrigerants. Do not reuse Seals / O-ring material from another system. The system piping has internal heat exchangers (IHX or IWT) as introduced in the G12 (7 series). SAFETY INFORMATION Several precautions need to be observed when working on automotive air conditioning systems: Always wear eye protection and gloves while handling refrigerant or servicing air conditioning system. Avoid breathing R1234yf lubricant vapor or mist. Use only approved service equipment to discharge A/C systems. If refrigerant or compressor oil contacts the skin or eyes, large quantities of cool water should be used to flush the affected area. Never heat a refrigerant container with an open flame. Keep all refrigerant away from open flames. Under no circumstances should R1234yf service equipment or vehicle A/C systems be pressure tested or leak tested with air/R1234yf mixtures. NOTE: The use of compressed air (shop air) for leak detection in an R1234yf system can contaminate the system and/or refrigerant with moisture. Leak detection equipment that meets the SAE J2791 standard will work with R1234yf Never use fittings for an R12 or R134a system on an R1234yf system. Any difficulty in connecting service equipm
NHTSA source summary · Original PDF not reviewed by Recallfolio
Howling Noise from the Rear Differential. When coasting from 85 - 70 mph, there is a howling noise from the rear differential. CAUSE Resonance behavior during the running-in phase of the PHEV rear differential
Source components: EQUIPMENT ADAPTIVE/MOBILITY · POWER TRAIN:DRIVELINE:DIFFERENTIAL UNIT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Vibrations Felt In Steering Wheel Only When Steering Wheel Heating Is Active. The customer states there is a small twitch/pulse of the steering wheel (1 second intervals) when the steering wheel heating is active. Note: The complaint is more noticeable with a cold steering wheel and vehicle voltage higher than 14 volts. Steering wheel control unit
NHTSA source summary · Original PDF not reviewed by Recallfolio
SI B11 26 15 March 2016 Engine Technical Service This Service Information Bulletin supersedes SI B11 26 15 dated February 2016. The upper crankshaft guide bearing may wear out prematurely. The wear on the upper guide bearing can cause the clutch pedal to malfunction during shifting. The Engine Malfunction warning may be illuminated and a fault will be stored in the DME memory for the crankshaft sensor. Noise may be heard from the lower engine and transmission bell housing area. Engine damage can occur in rare occasions.
Source components: ENGINE · EQUIPMENT ADAPTIVE/MOBILITY · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SI B84 03 14 February 2016 Communication Systems Technical Service This Service Information bulletin supersedes SI B84 03 14 dated October 2014. SUBJECT Bluetooth Connection Failures. There are various connectivity failures with the following devices: Apple iPhones Samsung S6 and the S6 Edge. Connectivity failure examples are: Call disconnection - Call is transferred back to the handset. In some instances the call is then transferred back to the vehicle. Contact List incomplete General connection failures CAUSE Apple iOS software (issue started with iOS 8.3 continues with iOS 9.x and its variants) Samsung S6 and S6 Edge device firmware CORRECTOPM None available at this time. We are currently working with the device manufacturer on a solution.
Source components: ELECTRICAL SYSTEM · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUBJECT Audio System Speaker Testing. For audio system speaker testing there is a NED (Non Electrical Diagnosis) Test Plan available. CAUSE We previously recommended use of the Audio Test CD (ATC) from BMW. This CD has been discontinued.
Source components: ELECTRICAL SYSTEM · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Service Information bulletin supersedes SI B64 09 15 dated January 2016. designates changes to this revision SUBJECT Whistling Noise Coming from the Center Vent - A/C is Off. A very high pitched whistling or beeping noise is heard coming from the center vents. The flow of refrigerant through the expansion valve at certain temperature differentials.
NHTSA source summary · Original PDF not reviewed by Recallfolio
February 2016 General Electrical Systems Technical Service This Service Information bulletin supersedes SI B61 03 14 dated May 2015. SUBJECT Check Control Messages Related to Battery Charge during Cold Ambient Temperatures. On cold days (an outside ambient temperature below 15F), customers may notice a check control message related to the battery displayed on the instrument cluster and the control information display. The check control message (ID 229) is caused by a heavily discharged battery. The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit).
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUBJECT Whistling Noise from the B-pillar. A whistling noise can be heard from the left or right side B-pillar area when the sunroof is open or tilted at highway speeds. Edge protection on the B-pillar
Source components: STRUCTURE:FRAME AND MEMBERS · VISIBILITY:SUN/MOON ROOF ASSEMBLY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUBJECT Noise from the Headliner. A scraping or groaning noise can be heard from the left or right side of the headliner from the A, B or C-pillar. The head air bag fabric may rub on the headliner.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SI B36 01 15 February 2016 Wheel and Tires Technical Service This Service Information bulletin supersedes SI 36 01 15 dated October 2015. designates changes to this revision SUBJECT Check Control Message: Tire Pressure Monitor (RDCi) Failure. A Check Control Message states Tire Pressure Monitor (RDCi) has failed CAUSE Hardware in the remote control unit (FBD3 antenna)
Source components: EQUIPMENT · TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS.