2013 BMW 328I Manufacturer communications & TSBs.Page 6
Original record summaries, dates and identifiers for this model-year. Records 501–600 of 633, ordered newest first. Dated records on this page: Feb 1, 2013–Mar 1, 2014.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Mar 1, 2014Service Bulletin/Repair Instructions
640613
NHTSA communication ID: 10147927
NHTSA source summary · Original PDF not reviewed by Recallfolio
A/C Cooling: Intermittent Reduction of Air Flow. The customer may complain of reduced air flow when the air conditioning system is operated for an extended time, usually longer than one hour. The complaint can vary due to one or more of the following variables: * High outside ambient temperature * Too much humidity * A/C temperature and fan settings set too low for too long Note: It is very difficult to duplicate this issue due the required outdoor weather conditions and length of driving time needed. CAUSE Evaporator starts to freeze up due to the position of the evaporator temperature sensor
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT:APPLIANCE:AIR CONDITIONER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Active Headlight Control Malfunction in Both Headlights. AHL (Active Headlight Control) malfunctions on both sides. Both lights aim either up or down while driving. CAUSE Broken mounting bolt holding on the rear height sensor bracket
NHTSA source summary · Original PDF not reviewed by Recallfolio
"?SI B12 24 13 March 2014 Engine Electrical SystemsTechnical Service This Service Information bulletin supersedes SI B12 24 13 dated January 2014. PERFORM THE PROCEDURE OUTLINED IN THIS SERVICE INFORMATION ON ALL AFFECTED VEHICLES BEFORE CUSTOMER DELIVERY OR THE NEXT TIME THEY ARE IN THE SHOP FOR MAINTENANCE OR REPAIRS. BMW centers must ensure Recalls are completed after having been notified by BMW of North America, LLC (BMWNA) that a safety-related defect or noncompliance exists in any motor vehicle or item of replacement equipment in the center's possession at the time of notification. In BMW NA's case, this notification would typically be made by the issuance of a Recall notification in the form of a Service Information bulletin (SIB) or transmission of a Dealer Communication System (DCS) Recall message. Under the National Traffic and Motor Vehicle Safety Act of 1966, as amended, if a Recall Campaign is announced by BMW NA, centers must ensure that all Recalls on new vehicles and new items of replacement equipment are completed BEFORE delivery to the consumer. This means that centers may not legally deliver new motor vehicles or new items of replacement equipment to consumers with an open Recall. The Safety Act also prohibits centers from selling or leasing the motor vehicle or item of replacement equipment, unless and until the open Recall has been completed BEFORE delivery. This also pertains to vehicles in the Certified Pre-Owned program, and to items of replacement equipment. Finally, BMW centers should not sell or use parts that have been recalled by BMW NA. Please follow the specific instructions provided by BMW NA on the return or disposition of the parts. designates changes to this revision SUBJECT Voluntary Emissions Recall Campaign 13E-A03: Program Control Units (OBD). Due to an error in the DME (Digital Motor Electronics) software, the required oxygen sensor onboard diagnostics (OBD) is not functioning. As a result, the ""Readiness bit"" confirmin
NHTSA source summary · Original PDF not reviewed by Recallfolio
iPhone Charging Status Constantly Switches On and Off. INFORMATION Do not replace any other parts! Advise the customer that he/she must use one of the following: * The original Apple iPhone/iPOD USB cable that came with the device * A BMW supplied iPhone/iPOD USB adapter cable PARTS INFORMATION
NHTSA source summary · Original PDF not reviewed by Recallfolio
Headunit-High: Navigation Road Map Installation After Replacement. When replacing the HU-H, the road map database version that was in the defective HU-H must be installed in the new HU-H.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Airbag Warning Light: ACSM FC 930A60 Seat Occupancy Detection. According to the customer, the airbag warning light was on, but it may not be on when the vehicle arrives in the workshop. ACSM fault code ""930A60 - Seat occupancy detection, front passenger; malfunction"" is stored. The fault may or may not currently be present. CAUSE The front passenger seat occupancy mat consists of a seat occupancy mat with a capacitive sensor system. This means a front passenger is detected by measuring the resistance of the human body. The fault is set when moisture is detected on the mat itself."
NHTSA source summary · Original PDF not reviewed by Recallfolio
Service Action: Replace Blower Motor Regulator. The blower motor regulator has an internal fault; after starting the engine, there may be a delay of up to a minute before the blower motor comes on CAUSE Faulty blower motor regulator (output stage)
Source components: ENGINE AND ENGINE COOLING · VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM:FAN/MOTOR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
?Taillight Is Loose in the Trunk Lid. The customer may notice the taillight is either loose or protruding outward from the trunk lid. CAUSE The taillight is not attached to the trunk lid properly due to the taillight design. If a customer complains of this taillight issue, an improved part is now available.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The Condition Based Service (CBS) due date is reset to 01/2000 and cannot be updated for: * Oil Service * Check Vehicle Note: No fault code is stored Software error in the Instrument Cluster
NHTSA source summary · Original PDF not reviewed by Recallfolio
?Sunroof Gets Stuck or Moves in Small Steps. During opening or closing the sunroof, one or more of the following situations may occur: 1. The sunroof becomes stuck 2. One-touch open and close no longer works 3. The sunroof moves in small steps. CAUSE Software error in the sunroof control module (FZD) Some or all of the following fault codes may be stored: 0x030212 - SHD: Activation timeout, no block recognition 0x030214 - SHD: Zero position passed, loss of calibration 0x030215 - SHD: Invalid characteristic curve, not normalized 0x030216 - SHD: 90% motor temperature threshold exceeded 0x030217 - SHD: Motor operation interrupted by overheating 0x030218 - SHD: Motor does not start due to overvoltage or undervoltage 0x030219 - SHD: Errors in the checksum coding 0x03021C - SHD: Not initialized due to invalid marginal conditions (motor driver) 0x030220 - SHD: System not normalized 0x801A02 - Coding: Control unit is not coded.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Noise from Rearview Mirror. Rattling noises can be heard from the rearview mirror when driving. CAUSE The mirror electrical connector is loose in the mirror base.
Source components: ELECTRICAL SYSTEM · VISIBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Service Action: Remove and Discard Water Drain Plugs from E-Box. Water leaks into the cabin due to clogged drain plugs in the E-boxes. CAUSE The drain plug slots are too small and clog.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Reduced Engine and Air-Conditioning Performance. When driving with high outside ambient temperatures, repeated stop and go, or high load operation over longer distances, the engine performance can be reduced. The air-conditioning system blower output may also be reduced, and in some circumstances the compressor is switched off. There could be any of the following faults stored depending on the conditions present at the time. DME * Fault 1A2108: Electric fan, self-diagnosis, interval stage 1: Minor fan fault EGS (also possibly set) * Fault 421722: DME/DDE interface: Forced upshift due to thermal engine protection request IHKA (possibly set without DME or EGS faults) * Fault 801224: Air conditioning compressor: Shut-down due to excess pressure in refrigerant circuit * Fault 801228: Blower output stage: Blower output reduction due to power management The Service Engine Soon lamp (MIL) would not be illuminated in these situations. 1. A DME software error in the control of the 850W electric fan over-boost or high speed function. 2. The electric cooling fan design was not robust enough for continuous over-boost or high speed operation.
Source components: ENGINE · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Enabling Code FSC/SWT - Enabling the Navigation System Map at QC1. The navigation system is inoperative unless the map is enabled during the QC1 Pre-Delivery Check. INFORMATION New vehicles come equipped with a navigation road map that must be enabled via an enable code (FSC). This process is part of the QC1 Pre-Delivery Check performed with the ISID (ISTA Diagnosis). IMPORTANT: There is no programming involved!
NHTSA source summary · Original PDF not reviewed by Recallfolio
"ConnectedDrive/BMW ASSIST Features Are Inoperative. ConnectedDrive features are partially or completely inoperative. * No traffic information (RTTI / ARTTI) * BMW ASSIST ""My Info"" service doesn't work. CAUSE The Electronic Subscriber Agreement (ESA) is inactive. * No active contract for ConnectedDrive features Offboard Availability (Backend) system issues * The external network was/is inoperative. * No data is sent to the vehicle."
NHTSA source summary · Original PDF not reviewed by Recallfolio
Headunit-High: INITIAL Enabling Code Is Not Accepted Via I-Drive. INFORMATION Do not replace any parts. NOTE: First time activation of the navigation system should always be performed during the Quality Certification 1 (QC1) Pre-Delivery Check, with the vehicle connected to the diagnosis system ISTA. Refer to SI B65 30 09. Connect the vehicle to the diagnosis system ISTA and activate the navigation system. The code is entered when running the QC1 Pre-Delivery Check test module. Refer to SI B09 04 09. IMPORTANT: No programming is required. WARRANTY INFORMATION Not applicable since the first time activation of the navigation system is part of the QC1 process and cannot be claimed separately.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Service Action: Replace Blower Motor Regulator. The blower motor regulator has an internal fault; after starting the engine, there may be a delay of up to a minute before the blower motor comes on CAUSE Faulty blower motor regulator (output stage)
NHTSA source summary · Original PDF not reviewed by Recallfolio
?SI B64 06 13 January 2014 Body EquipmentTechnical Service This Service Information bulletin supersedes SI B64 06 13 dated November 2013. designates changes to this revision SUBJECT A/C Cooling: Intermittent Reduction of Air Flow. The customer may complain of reduced air flow when the air conditioning system is operated for an extended time, usually longer than one hour. The complaint can vary due to one or more of the following variables: * High outside ambient temperature * Too much humidity * A/C temperature and fan settings set too low for too long Note: It is very difficult to duplicate this issue due the required outdoor weather conditions and length of driving time needed. CAUSE Evaporator starts to freeze up due to the position of the evaporator temperature sensor
Source components: ENGINE AND ENGINE COOLING · VISIBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
One or Both Trunk Lid Tail Lamps Malfunction. One of the tail lamps is out in the trunk lid light cluster. This is accompanied by one of the following CCM (Check Control Messages): * Tail lamp in tailgate malfunction * Rear fog light malfunction * Reversing light malfunction CAUSE Bulb socket, rear lamp in trunk lid defective
NHTSA source summary · Original PDF not reviewed by Recallfolio
Delay in Automatic Driving Light Switching On/Off. When driving out of a tunnel or exiting underground parking, the automatic driving light remains switched on for two minutes, even in daylight. The automatic driving light switching on/off can be shorter or longer when it starts to get dark. CAUSE The software for the switch-on threshold is lowered to protect the xenon light source.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Fog Light Operation Changed After Programming. After the vehicle is programmed with ISTA/P 2.49.x or 2.50.x (integration level earlier than F02013-11-502), the fog lights cannot be operated when the light switch is in the parking light position. Note: The fog light operation has been changed in vehicles produced from March 2013. The fog lights cannot be operated when the light switch is in the park position. This is normal operation due to state legislative requirements that have changed; no further action is required. CAUSE Software error with ISTA/P 2.49.x and 2.50.x
NHTSA source summary · Original PDF not reviewed by Recallfolio
ELV Does Not Release. Cause 1: The steering column is held against the steering lock because of torque from the steering gear. In such cases, a yellow check control warning (CC ID# 187) is shown in the instrument cluster, but no faults are stored. Cause 2: Communication fault in the CAS (Car Access System) and ELV system network and/or battery low. The problem may cause the ELV warning to be displayed in yellow or red.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Erroneous Trunk Lid Open Check Control Message. The trunk open check control message may appear, even though the trunk lid or tailgate is fully closed and latched. CAUSE Incorrect adjustment of the trunk latch striker
NHTSA source summary · Original PDF not reviewed by Recallfolio
Service Action: Remove Water Drain Plugs from E-Box. The water drain plugs for the left- and right-side E-box may clog. This can lead to water collection/corrosion and allow water to enter the passenger compartment. CAUSE The water drain plug slots are too small.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Squeaking Noises when Steering Wheel Is Turned. There are squeaking noises from the steering spindle when the steering wheel is turned. The steering spindle gaiter is insufficiently lubricated.
NHTSA source summary · Original PDF not reviewed by Recallfolio
GM6 - 6L45R: Diagnostic Procedure for Shudder or Vibration Issues. A shudder or vibration can be felt under light acceleration or when driving at constant suburban speeds. This can be most noticeable in the 1700 - 2200 engine rpm range while in 3rd through 6th gears. No faults are stored in the EGS module. CAUSE Changes in the frictional properties of the automatic transmission fluid over time can lead to momentary slipping of the torque convertor lock-up clutch.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Exhaust Flap Actuator Is Loose. INFORMATION Covered under the terms of the BMW New Vehicle/SAV Limited Warranty Defect Code:18 12 03 39 00https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/159...2/5/2014 Page 2 of 2 Labor Operation:Labor Allowance:Refer to KSDReplacing exhaust flap actuator driveLabor operation code 18 12 081 is a Main labor operation. If you are using a Main labor code for another repair, use the Plus code labor operation 18 12 581 instead. Refer to KSD2 for the corresponding flat rate unit (FRU) allowance. Enter the Chassis Number, which consists of the last 7 digits of the Vehicle Identification Number (VIN). Click on the ""Search"" button, and then enter the applicable flat rate labor operation in the FR code field."
Source components: ENGINE · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"PERFORM THE PROCEDURE OUTLINED IN THIS SERVICE INFORMATION ON ALL AFFECTED VEHICLES BEFORE CUSTOMER DELIVERY OR THE NEXT TIME THEY ARE IN THE SHOP FOR MAINTENANCE OR REPAIRS. BMW centers must ensure Recalls are completed after having been notified by BMW of North America, LLC (BMWNA) that a safety-related defect or noncompliance exists in any motor vehicle or item of replacement equipment in the center's possession at the time of notification. In BMW NA's case, this notification would typically be made by the issuance of a Recall notification in the form of a Service Information bulletin (SIB) or transmission of a Dealer Communication System (DCS) Recall message. Under the National Traffic and Motor Vehicle Safety Act of 1966, as amended, if a Recall Campaign is announced by BMW NA, centers must ensure that all Recalls on new vehicles and new items of replacement equipment are completed BEFORE delivery to the consumer. This means that centers may not legally deliver new motor vehicles or new items of replacement equipment to consumers with an open Recall. The Safety Act also prohibits centers from selling or leasing the motor vehicle or item of replacement equipment, unless and until the open Recall has been completed BEFORE delivery. This also pertains to vehicles in the Certified Pre-Owned program, and to items of replacement equipment. Finally, BMW centers should not sell or use parts that have been recalled by BMW NA. Please follow the specific instructions provided by BMW NA on the return or disposition of the parts. designates changes to this revision SUBJECT Voluntary Emissions Recall Campaign 13E-A03: Program Control Units (OBD). Due to an error in the DME (Digital Motor Electronics) software, the required oxygen sensor onboard diagnostics (OBD) is not functioning. As a result, the ""Readiness bit"" confirming a successful completion of the oxygen sensor diagnostics will not be set. In order to remedy the situation, BMW is conducting a Voluntary Emissions
NHTSA source summary · Original PDF not reviewed by Recallfolio
?N20 and N26 Engine: Various VANOS System Faults Stored in DME. The Service Engine Soon lamp and Engine Malfunction warning are illuminated, and the vehicle has reduced power output. This situation can occur as a customer complaint, or after performing repairs to the engine valve train assembly. One or more of the following faults is stored in the DME. F10, F25, F30, F31 and F34: 131401 VANOS, exhaust, starting from cold: Non-adjustable 131501 VANOS, intake, starting from cold: Non-adjustable 131808 VANOS, exhaust, starting from cold: Position not reached 131908 VANOS, intake, starting from cold: Position not reached 130104 VANOS, intake, control fault, camshaft jammed 130304 VANOS, exhaust, control fault, camshaft jammed 130308 VANOS, exhaust, control fault, position not reached 130108 VANOS, intake, control fault, position not reached E84 and E89: 2D54 VANOS, exhaust, starting from cold: Non-adjustable 2D55 VANOS, intake, starting from cold: Non-adjustable 2D56 VANOS, exhaust, starting from cold: Position not reached 2D57 VANOS, intake, starting from cold: Position not reached 2D60 VANOS, exhaust, control fault, camshaft jammed 2D5A VANOS, intake, control fault, camshaft jammed 2D5B VANOS, intake, control fault, position not reached 2D61 VANOS, exhaust, control fault, position not reached If one of the applicable faults listed above is not stored in the DME fault memory then continue troubleshooting with the applicable test plan for the fault(s) stored. CAUSE This is due to a diagnostic programming error in the DME.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Service Information bulletin B36 03 13 has been published for the Delivery Stop issued on Wednesday, November 13. The Delivery Stop affects certain 2014 model year F30, F31 and F32 October 2013 production vehicles. Tire Identification numbers (molding number and DOT number) must be checked and if necessary, affected tires replaced. Affected vehicles in center inventory must not be delivered until the tires have been checked. The small number of affected vehicles can be identified via the Key Reader, DCS Inquiry or ISPA with the description: Defect Code 0036820100, Delivery Stop, B36 03 13 Check Tire ID
NHTSA source summary · Original PDF not reviewed by Recallfolio
"USB Connection Not Working. One, or both of the scenarios listed below may be encountered: 1. The message ""Device not supported"" is displayed in the CID after connecting a USB device to the USB port using a USB cable. 2. The ""USB option"" in the menu cannot be selected (grayed out), after the vehicle was programmed with ISTA/P 2.50.2, or 2.50.3: I-Level F020-13-07-503, or F020-13-07-505. CAUSE 1. Incompatible USB cable is being used 2. Head Unit Basic software error 1 The following procedure should be performed for ""Situation 1, Cause 1"" listed above: Part A (Steps 1 to 3) 1. Duplicate the issue. 2. Verify that the USB cable which is being used, is the original cable for the device and not an aftermarket cable. 3. If the issue is resolved when using an original USB cable supplied by the manufacturer of the device, do not perform step 4 listed below. No further action is required. Part B (Step 4) 4.If the issue is still present when using the original cable from the device manufacturer, proceed to program and code the vehicle using ISTA/P 2.51.0 or higher. ? I-Level after programming would be F020-13-11-501, or higher. Note that ISTA/P will automatically reprogram and code all programmable control modules that do not have the latest software. For information on programming and coding with ISTA/P, refer to CenterNet / Aftersales Portal / Service / Workshop Technology / Vehicle Programming."
NHTSA source summary · Original PDF not reviewed by Recallfolio
Touchpad Integrated in the iDrive Controller Is Intermittently Inoperative. Intermittently the Touchpad integrated in the iDrive controller is inoperative. * No entries can be made using the Touchpad * Fault code is stored in the touch-box control unit Software error in the touch-box control unit (TBX)
NHTSA source summary · Original PDF not reviewed by Recallfolio
A/C Cooling: Intermittent Reduction of Air Flow. The customer may complain of reduced air flow when the air conditioning system is operated for an extended time, usually longer than one hour. The complaint can vary due to one or more of the following variables: * High outside ambient temperature * Too much humidity * A/C temperature and fan settings set too low for too long Note: It is very difficult to duplicate this issue due the required outdoor weather conditions and length of driving time needed. CAUSE Evaporator starts to freeze up due to the position of the evaporator temperature sensor
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT:APPLIANCE:AIR CONDITIONER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Daytime Running Light Does Not Switch ON. The DRL (Daytime Running Light) is off and cannot be switched on after importing the personal profile from another vehicle. The CID (Central Information Display) display shows that it is active. CAUSE Software error when importing the personal profile from a vehicle which has a different head unit
Source components: ELECTRICAL SYSTEM · EXTERIOR LIGHTING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Integrated Owner's Manual No Longer Available After Programming. After a programming or replacement of the Front Electronics Module (FEM), the customer states that the Integrated Owner's Manual (IBA) can no longer be selected in the vehicle. CAUSE FEM application error
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Outside Door Mirror Moves when Locking or Unlocking the Vehicle. The door mirror tilts immediately after unlocking or locking. The mirror position does not correspond to the memory position preset by the customer. Pressing the seat memory button typically will return the mirror to the stored position. Poor electrical contacts of the mirror drive in the mirror housing INFORMATION The problem has been integrated into ISTA diagnostics. Complete the diagnosis test plan using the latest ISTA version. The test plan can be accessed via the following path: ""Information Search / Function Structure / Body / Mirror / Exterior mirrors / Driver's or passenger side / Exterior Mirror https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/15...12/6/2013 Page 2 of 2 Malfunction,"" and then press ""Start Search."" Select the test plan ""AM5102_00010."""
Source components: ELECTRICAL SYSTEM · STRUCTURE · VISIBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"?PERFORM THE PROCEDURE OUTLINED IN THIS SERVICE INFORMATION ON ALL AFFECTED VEHICLES BEFORE CUSTOMER DELIVERY OR THE NEXT TIME THEY ARE IN THE SHOP FOR MAINTENANCE OR REPAIRS. SUBJECT Service Action: Continental Tires, Inspect and Replace if Necessary. During manufacturing process of the Continental tires, there may have been a deviation from the production specifications. AFFECTED VEHICLES This Service Action involves F30, F31 and F32 vehicles. In order to determine whether a specific vehicle has had this Service Action completed or is affected by this Service Action, first check the B-pillar label for code number 659. If code number 659 has been punched out, the campaign has already been performed. If code number 659 has not been punched out, it will be necessary to utilize the ""Service Menu"" of DCSnet (Dealer Communication System) or the Key Reader. Based on the response of the system, either proceed with the corrective action or take no further action."
NHTSA source summary · Original PDF not reviewed by Recallfolio
Incorrect Remaining Service Life from CBS Data for Brake pads. The calculated remaining service life for the brake pads (front and/or rear axle) from the CBS data does not match the actual brake pad thickness. The customer notices implausible remaining distances (too high or too low) on the front and/or the rear axle brake system. Note: E9x vehicles with xDrive are not affected by this bulletin. Software calculation in the brake pad wear model
NHTSA source summary · Original PDF not reviewed by Recallfolio
Service Action: Program Control Units (Direct Ozone Reduction). The DME diagnostic for direct ozone reduction, by means of the environmental air catalyst sensor (EAC) located in the radiator, is not carried out correctly as required by emissions regulations.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
N55: Engine Difficult to Start at Cold Ambient Temperatures. The complaint may include any of the following symptoms: * The engine stalls immediately after a cold start before driving away * The engine may run roughly or misfire after a cold start * The engine does not start cold or may take several attempts * To assist starting when cold, the accelerator may need to be depressed slightly and the idle speed raised for a few seconds so the engine does not stall This can occur most frequently at outside ambient temperatures between -15°C and + 15°C. It is possible that the Service Engine Soon (MIL) lamp is on with misfire fault(s) stored, but it is equally possible that there will be no faults stored in the DME. Unfavorable DME software Cold start or idling problems may arise due to poor fuel quality. The use of summer fuel during cold outside temperatures may also lead to such problems.
NHTSA source summary · Original PDF not reviewed by Recallfolio
MN16 Engine: FC 2D9B Knock Sensor, Signal Is Stored in the DME. Certain areas of the US experience extremely cold climate conditions during the winter months, which can cause the Service Engine Soon lamp to illuminate while the engine temperature is increasing to full operating temperature. The following fault may be stored in the DME: ??FC 2D9B Knock Sensor, Signal CAUSE Unfavorable DME knock sensor diagnostic at outside ambient temperatures below -5° C
Source components: ENGINE · POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Intermittently Stored FM Radio Stations Default to FM 87.7. Intermittently, the stored FM radio stations default to FM 87.7 after vehicle start-up. CAUSE 1. Low battery voltage or voltage drop at the head unit 2. Radio station preset contains FM 87.7 3. Remote key memory not set correctly or the setting is lost
NHTSA source summary · Original PDF not reviewed by Recallfolio
"The replacement OC3 seat mat (front passenger seat occupancy) will not enable when following ISTA Repair Instruction REP 65 77 604, ""Replacing sensor mat (OC3 mat) for passenger seat occupancy detector."" 1. When the new mat is installed in the vehicle, too much pre-load pressure will prevent the mat from being enabled. ISTA/P WILL NOT enable the new part, and will cause permanent damage to it. 2. The new part has incorrect coding."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"ACSM and ICM Warning Lamps Are Illuminated. Various warning lamps and check control messages relating to the ACSM and ICM systems are illuminated. Many ""No Message"" faults are stored for various control modules. The ACSM and ICM modules may also not be responding to a vehicle test in ISTA. CAUSE Ground point Z10*10B is loose."
NHTSA source summary · Original PDF not reviewed by Recallfolio
Noise from Steering Column Switch Cluster when Turning. A scraping noise is heard from the SZL (Steering Column Switch Cluster) area. This occurs when turning the wheel from 30 to 60 degrees. CAUSE The unlocking pin in the SZL makes contact with the steering wheel.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Rattling Noise in the Front Door. The customer may complain of a rattling noise from the front door panel when the vehicle is in motion. CAUSE The wiring harness near the tweeter is not routed correctly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SI B17 02 12 October 2013 Cooling SystemsTechnical Service This Service Information bulletin supersedes SI 17 02 12 dated November 2012. designates changes to this revision SUBJECT Low Coolant Warning Is Displayed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
N55 Engine: Erroneous Service Engine Soon Lamp Illuminated with Mixture Faults Stored in the DME. INFORMATION An error has been identified in the current version of ETK regarding N55 fuel injector replacement part numbers and production dates. Installing the incorrect injector part number can lead to an erroneous Service Engine Soon lamp illumination and various mixture faults stored in the DME. Correct part numbers and applicable production dates: P/N 13 64 7 639 994 is for all vehicles produced from 7/2013 P/N 13 64 7 597 870 is for all vehicles produced from 1/2011 to 7/2013 P/N 13 53 7 568 607 is for all vehicles produced to 1/2011 It is good practice to verify that the part number being removed from the engine matches the new injector part number, until further notice. When the ETK data is corrected, a notification will be distributed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Service Action: Program Control Units (MSA). Certain MY 2014 F34 vehicles were produced with the MSA (automatic engine start/stop) mode set to "Default on."
NHTSA source summary · Original PDF not reviewed by Recallfolio
?Blower Makes an Unusual Noise. An unusual howling noise is heard coming from the glove compartment and passenger foot well area (blower motor). 6. Remove the cover (1) by loosening the three fasteners circled in red, and then remove the side panel trim piece (2) by CAUSE Foreign material such as leaves may have entered the blower motor via the fresh air intake.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Head-up Display: Navigation Information Is Not Displayed. The navigation system information (turn advice - arrow view) is no longer displayed on the Head-up Display (HUD). Turning the ignition on and off doesn't resolve the issue. Application error between the instrument cluster and the Head-up Display
NHTSA source summary · Original PDF not reviewed by Recallfolio
Sunroof Gets Stuck or Moves in Small Steps. During opening or closing the sunroof, one or more of the following situations may occur: 1. The sunroof becomes stuck 2. One-touch open and close no longer works 3. The sunroof moves in small steps. CAUSE Software error in the sunroof control module (FZD) Some or all of the following fault codes may be stored: 0x030212 - SHD: Activation timeout, no block recognition 0x030214 - SHD: Zero position passed, loss of calibration 0x030215 - SHD: Invalid characteristic curve, not normalized 0x030216 - SHD: 90% motor temperature threshold exceeded 0x030217 - SHD: Motor operation interrupted by overheating 0x030218 - SHD: Motor does not start due to overvoltage or undervoltage 0x030219 - SHD: Errors in the checksum coding 0x03021C - SHD: Not initialized due to invalid marginal conditions (motor driver) 0x030220 - SHD: System not normalized 0x801A02 - Coding: Control unit is not coded
NHTSA source summary · Original PDF not reviewed by Recallfolio
N20 Engine: Ticking Noise from High-pressure Fuel Pump. The customer complains of a high-frequency ticking noise from the engine compartment. The noise can be heard inside and outside the vehicle. Mechanical vibrations inside the high-pressure fuel pump
NHTSA source summary · Original PDF not reviewed by Recallfolio
N55 Engine: Erroneous Service Engine Soon Lamp Illuminated with Mixture Faults Stored in the DME. INFORMATION An error has been identified in the current version of ETK regarding N55 fuel injector replacement part numbers and production dates. Installing the incorrect injector part number can lead to an erroneous Service Engine Soon lamp illumination and various mixture faults stored in the DME. Correct part numbers and applicable production dates: P/N 13 64 7 639 994 is for all vehicles produced from 7/2013 P/N 13 64 7 597 870 is for all vehicles produced up to 7/2013
NHTSA source summary · Original PDF not reviewed by Recallfolio
N20 and N26 Engine: Various VANOS System Faults Stored in DME. The Service Engine Soon lamp and Engine Malfunction warning are illuminated, and the vehicle has reduced power output. Various faults related to VANOS operation are stored in the DME. While performing the test plan, the results may appear to be inconclusive because the fault will not clear from DME fault memory. CAUSE This is due to a programming error associated with ISTA/P 2.49 and lower. The error is corrected with ISTA/P 2.50.2 or higher.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Tail Lamp Is Loose in theTrunk Lid. The customer may notice the tail lamp is either loose or protruding outward from the trunk lid. CAUSE The tail lamp is not attached to the trunk lid properly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Key Intermittently Not Detected and Not Possible to Start Engine. Intermittently it is not possible to start the engine. Terminal 15 cannot be switched on. The remote control key is not detected inside the vehicle. The following check control messages are displayed: * ""Remote control not present or disrupted. Not possible to start engine"" * ""No remote control. Not possible to start engine"" Note: The vehicle can still be started via the emergency start coil on the side of the steering column. Front Electronic Module (FEM) software error"
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Service Action: Repair Corrosion Protection on the Trunk B+ Connector. The corrosion protection on the outside of the trunk (back of rear right-hand wheel arch) around the battery positive connector is insufficient, and leads to corrosion on the body. AFFECTED VEHICLES This Service Action involves F30 vehicles which were produced from 9/2011 to 10/2012. In order to determine whether a specific vehicle has had this Service Action completed or is affected by this Service Action, first check the B-pillar label for code number 645. If code number 645 has been punched out, the campaign has already been performed. If code number 645 has not been punched out, it will be necessary to utilize the ""Service Menu"" of DCSnet (Dealer Communication System) or the Key Reader. Based on the response of the system, either proceed with the corrective action or take no further action."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Outside Door Mirror Moves when Locking or Unlocking the Vehicle. The door mirror tilts immediately after unlocking or locking. The mirror position does not correspond to the memory position preset by the customer. Pressing the seat memory button typically will return the mirror to the stored position. Poor electrical contacts of the mirror drive in the mirror housing INFORMATION The problem has been integrated into ISTA diagnostics. Complete the diagnosis test plan using the latest ISTA version. The test plan can be accessed via the following path: ""Information Search / Function Structure / Body / Mirror / Exterior mirrors / Driver's or passenger side / Electrochromic Mirror,"" and then press ""Start Search."" Select the test plan ""AM5102_00010."""
NHTSA source summary · Original PDF not reviewed by Recallfolio
Brake Fluid Maintenance Service: 36-Month Interval. The CBS displays the first brake fluid service as a 36-month interval from the date of production instead of the appropriate 24-month interval.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Squeaking Noises when Steering Wheel Is Turned. There are squeaking noises from the steering spindle when the steering wheel is turned. The steering spindle gaiter is insufficiently lubricated.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The Service Engine Soon Lamp On with Post Oxygen Sensor Faults Stored. The Service Engine Soon (MIL) lamp is on and the following faults are stored in the DME fault code memory. BN2000 (E-Series) vehicles: * 2D22: Oxygen sensor downstream of catalytic converter, electric: open circuit BN2020 (F-Series) vehicles: * 12AB04: Oxygen sensor downstream of catalytic converter, electric: open circuit * 12AC04: Oxygen sensor downstream of catalytic converter 2, electric: open circuit These faults may occur sporadically after a long MSA engine stop. Unfavorable DME software diagnostics (fault is erroneous) This software error affects vehicles produced from 3/2013 to 6/2013, as well as older vehicles which have been programmed during service work to a current integration level of Xxxx-13-03-5xx.
NHTSA source summary · Original PDF not reviewed by Recallfolio
No Flashing Confirmation when DWA Is Activated. The DWA alarm (Anti-theft Alarm System) has no confirmation if the vehicle is unlocked with the hood open and then locked again. CAUSE Software error in the DWA
NHTSA source summary · Original PDF not reviewed by Recallfolio
Service Action: Repair Corrosion Protection on the Trunk B+ Connector. The corrosion protection on the outside of the trunk (back of rear right-hand wheel arch) around the battery positive connector is insufficient, and leads to corrosion on the body.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Brake Fluid Maintenance Service: 36-Month Interval. The coding in these vehicles has the CBS displaying the first brake fluid service as a 36-month interval from the date of production, instead of the appropriate 24-month interval.
NHTSA source summary · Original PDF not reviewed by Recallfolio
N20 and N26 Engine: Various VANOS System Faults Stored in DME. The Service Engine Soon lamp is illuminated; Engine Malfunction warning is illuminated; and the vehicle has reduced power output. Various faults related to VANOS operation are stored in the DME. While performing the test plan, the results may appear to be inconclusive because the fault will not clear from DME Fault Memory. The ISTA/D diagnostic test plan does incorporate a VANOS bleed function, but it does not advise the technician to bleed the VANOS system after a VANOS or engine oil supply component replacement. CAUSE This is due to an error in the current level of ISTA/D. The error will be corrected with ISTA/D 2.41.0.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Headunit Basic: Intermittently No AM Radio Reception. The Headunit Basic (HU-B), also called Radio Professional or ENTRY head unit, intermittently does not have AM radio reception after starting the vehicle when left in AM mode. * Only hissing or static noise can be heard * AM radio stations are correctly displayed Proper function can be restored by switching to FM mode and back to AM mode. No fault code is stored in the head unit. Software issue in the HU-B
NHTSA source summary · Original PDF not reviewed by Recallfolio
Condition Based Service Due Date Is Reset to 01/2000. The Condition Based Service (CBS) due date is reset to 01/2000 and cannot be updated for: * Oil Service * Check Vehicle Note: No fault code is stored Software error in the Instrument Cluster
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"BMW NA has agreed to extend the emissions warranties of the turbocharger's wastegate to: ??8 years or 82,000 miles, whichever occurs first, as determined from the vehicle's original in-service date select the ""Vehicle Comment"" button to display the extended coverage information. The terms of the original New Vehicle/SAV Limited Warranty and applicable emissions warranty still apply. BMW NA will not provide warranty coverage to any Settlement Class Member's vehicle containing modifications or alterations to the turbocharger or its wastegates (software, hardware or otherwise), or evidencing other conditions not normally covered under the original New Vehicle/SAV Limited Warranty or applicable emissions warranty. Modifications excluded from warranty coverage include any aftermarket parts that affect the turbocharger system, or if there are other conditions that would normally exclude it from warranty coverage."
NHTSA source summary · Original PDF not reviewed by Recallfolio
iPhone Charging Status Constantly Switches On and Off. Do not replace any other parts! Advise the customer that he/she must use one of the following: * The original Apple iPhone/iPOD USB cable that came with the device * A BMW supplied iPhone/iPOD USB adapter cable PARTS INFORMATION Part Number
NHTSA source summary · Original PDF not reviewed by Recallfolio
TCB: Emergency Call Is Erroneously Triggered. An emergency call is erroneously made with no input from the driver. The following fault codes are stored in the TCB: * 0xB7F325 - Emergency call loud speaker: break in circuit * 0xB7F319 - Emergency call button: short circuit * 0xB7F326 - Emergency call loud speaker: short circuit to earth * 0xB7F33E - Automatic emergency call triggered frequently CAUSE TCB control unit error
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Safety Belt Extender ""Handover"" Fails to Deliver the Belt to the Customer. The customer states that the seat belt extender ""handover"" on the front driver's or passenger side failed to deliver the belt. One or more of the following situations may apply: * The safety belt extender extends but the belt slips off. * The ""hand"" on the extender fails. * The safety belt is twisted. * The extender will not operate and makes noise while extending. S One or more of the following causes may apply: 1. The safety belt is incorrectly positioned. 2. The ""hand"" on the extender has mechanically failed. 3. The safety belt slips off the ""hand"" due to excessive resistance from the seat belt reel, not allowing the belt to extend properly. The seat belt is twisted. 4. The safety belt slips off the ""hand"" due to the belt material being excessively worn. 5. The safety belt extender fails to extend or retract intermittently due to FRM (Footwell Module) software. 6. The safety belt extender is noisy or inoperative, due to a communication problem or incorrect power or ground."
NHTSA source summary · Original PDF not reviewed by Recallfolio
The PDC system falsely detects obstacles on all front and rear sensors when no obstacles are present around the vehicle. Software error in the REM (Rear Electronic Module)
NHTSA source summary · Original PDF not reviewed by Recallfolio
In all audio modes (radio, CD, AUX-In, etc.), the audio output is distorted. It is more noticeable with high bass and high audio volume settings. There may also be an intermittent interference noise coming from the loudspeakers at low audio volume or when the radio is turned off. Audio settings in the RAD2+ (radio professional)
NHTSA source summary · Original PDF not reviewed by Recallfolio
Head-up Display: Navigation Information Is Not Displayed. The navigation system information (turn advice - arrow view) is no longer displayed on the Head-up Display (HUD). Turning the ignition on and off doesn't resolve the issue. Application error between the instrument cluster and the Head-up Display
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
"REM: Various Electrical Faults in Rear of a Vehicle. Various electrical faults associated with the rear of the vehicle occur, including one or more of the following: * The REM (Rear Electronic Module) does not respond to diagnosis. * The one-touch function of the rear power windows is inoperative. * The rear power windows cannot be initialized. * The trunk lid cannot be opened. * The brake lights are not working (check control message ""Left/right brake light failed"" is displayed). * The rear turn indicator lights are not working (check control message ""Rear left/right turn indicator failed"" is displayed). One or more of the following faults are stored in the REM: * ""804805 Internal software control unit fault"" * ""804876 Turn indicator, rear left, faulty"" * ""804877 Turn indicator, rear right, faulty"" * ""804872 Brake light, left, faulty"" * ""804874 Brake light, right, faulty"" * ""30195 Window regulator, passenger's side door, rear: invalid characteristic curve, no normalization present"" * ""30115 Power window, rear door on driver's side: invalid characteristic curve, no normalization present"" * ""301A0 Window regulator on passenger's side door, rear: system is not normalized"" * ""30120 Power window, rear door on driver's side: system is not standardized"" CAUSE Rear power window drive(s) faulty"
NHTSA source summary · Original PDF not reviewed by Recallfolio
DSC Warning Light is On. The warning lamps for DSC, ABS and brake warning are illuminated. There may also be a warning in the control display for 'Chassis Control System failure' One or more of the following fault codes are stored: F25, F30 DSC * D36D44 - Signal error longitudinal torque distribution (LMV) * 48097D - Transfer Case clutch position open F01, F02, F07, F10, F12 and F13 LMV: * 440108 - Control Unit internal error * 44010F - Control Unit internal error E70, E71 and E84 LMV: * 5219 - Control Unit: EEPROM Writing-reading-error * 522D - Control Unit: internal Error CAUSE Software calibration error in the LMV
NHTSA source summary · Original PDF not reviewed by Recallfolio
Electronic Power Steering (EPS) Fails when Starting: Fault Code 4823E1. The EPS fails briefly when starting the engine. FC 4823E1 is stored in the EPS_20 control unit. CAUSE Specific undervoltage situation during engine starting.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"The warning lamps for DSC, ABS and brake warning are illuminated. There may also be a warning in the control display for ""Chassis Control System failure."" One or more of the following fault codes are stored: DSC: * D36D44 - Signal error longitudinal torque distribution (LMV) * 48097D - Transfer Case clutch position open F01, F02, F07, F10, F12 and F13 LMV: * 440108 - Control Unit internal error * 44010F - Control Unit internal error E70, E71 and E84 LMV: * 5219 - Control Unit: EEPROM Writing-reading-error * 522D - Control Unit: internal Error CAUSE Software calibration error in the LMV"
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"N54 Engine: Diagnosis of Cold Start Rough Running with Misfire Faults. The customer may complain that during the cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. Various misfire fault codes (e.g., 29CC, 29D2, 29D1, 29D0, 29C0, 29CF) may be stored in the DME control module. The engine rough running complaint can be reproduced on a cold start in the workshop. During the course of diagnosis, the spark plugs, removed from the misfiring cylinders after the problem was reproduced, are found to be soaked (""wet"") with fuel, while the injector tips are covered with a layer of carbon deposit. Possible cause: high-pressure injector failure (leakage or incorrect spraying pattern) due to internal wear or unfavorable stock of tolerances IMPORTANT: For comprehensive N54 drivability diagnostics, always refer to the ""N54 Engine Diagnostic Fault Tree"" file (the current version ""02_14_13"" is found as a PDF attachment to SI B12 55 06)."
NHTSA source summary · Original PDF not reviewed by Recallfolio
Service Engine Soon Light Flashes with Throttle Adaptation Faults Stored. The EML light flashes with a check control message for reduced power output and/or the Service Engine Soon lamp (MIL) flashes. During the throttle valve adaptation (teach-in limit run), faults may occur due to signal voltage oscillations. This could lead to a termination of the teach-in routine or an incorrect value taught in at the lower limit. The following faults can be stored in the DME memory: E82, E84, E88, E89, E92, and E93 BN2000 vehicles * 28D0: throttle valve, adaptation: Initial adaptation, lower limit not taught in * 28D4: throttle valve, adaptation: Subsequent teach-in, lower limit not taught in * 28C4: throttle valve, adaptation: Emergency air position not adapted * 28A0: throttle valve angle - Intake manifold absolute comparison: pressure too high ??3166: Tank-ventilation system: fault F01, F02, F06, F07, F10, F12, F13, F30, F31, and ALPINA B7 BN2020 vehicles: * 101408: throttle valve, adaptation: Initial adaptation, lower limit not taught in * 107AE0: throttle valve, adaptation: Subsequent teach-in, lower limit not taught in * 101402: throttle valve, adaptation: Emergency air position not adapted * 101F01: throttle valve angle - Intake manifold absolute comparison: pressure too high ??190F08: Tank-ventilation system: fault Sensitivity of the throttle valve sensor (only affects parts installed during this production period)
NHTSA source summary · Original PDF not reviewed by Recallfolio
PERFORM THE PROCEDURE OUTLINED IN THIS SERVICE INFORMATION ON ALL AFFECTED VEHICLES BEFORE CUSTOMER DELIVERY OR THE NEXT TIME THEY ARE IN THE SHOP FOR MAINTENANCE OR REPAIRS. BMW centers must ensure recalls are completed after having been notified by BMW of North America, LLC (BMWNA) that a safety-related defect or noncompliance exists in any motor vehicle or item of replacement equipment in the center's possession at the time of notification. In BMW NA's case, this notification would typically be made by the issuance of a recall notification in the form of a Service Information bulletin (SIB) or transmission of a Dealer Communication System (DCS) recall message. Under the National Traffic and Motor Vehicle Safety Act of 1966, as amended, if a recall campaign is announced by BMW NA, centers must ensure that all recalls on new vehicles and new items of replacement equipment are completed BEFORE delivery to the consumer. This means that centers may not legally deliver new motor vehicles or new items of replacement equipment to consumers with an open recall. The Safety Act also prohibits centers from selling or leasing the motor vehicle or item of replacement equipment, unless and until the open recall has been completed BEFORE delivery. This also pertains to vehicles in the Certified Pre-Owned program, and to items of replacement equipment. Finally, BMW centers should not sell or use parts that have been recalled by BMW NA. Please follow the specific instructions provided by BMW NA on the return or disposition of the parts. SUBJECT Voluntary Emissions Recall Campaign 13E-A02: Replace Emissions Label. Certain vehicles were produced without the required emissions label installed on the underside of the engine hood. Customers will receive notification letters informing them to make a service appointment at their BMW centers to have the correct label installed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Rear-view Camera Does Not Turn On Automatically. When the reverse gear is selected, the rear-view camera does not turn on automatically. The driver must activate the rear-view camera using the iDrive controller or the camera button. CAUSE Software error in the Front Electronics Module (FEM)
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Headunit-Basic: CID is blank and ""NO SIGNAL"" is Displayed. Intermittently the Central Information Display (CID) is blank and ""NO SIGNAL"" is displayed on the CID. ??Fault Code B7F8C3 ""no response from CID (HW error: loss of CID communication)"" is stored in the HU-B Error in the Headunit-Basic (HU-B), also called Radio Professional or ENTRY head unit."
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
In all audio modes (radio, CD, AUX-In, etc.), the audio output is distorted. It is more noticeable with high bass and high audio volume settings. There may also be an intermittent interference noise coming from the loudspeakers at low audio volume or when the radio is turned off. Audio settings in the RAD2+ (radio professional)
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Enabling and Replacing New OC3 Seat Mat. The replacement OC3 seat mat (front passenger seat occupancy) will not enable when following ISTA Repair Instruction REP 65 77 604, ""Replacing sensor mat (OC3 mat) for passenger seat occupancy detector."" When the new mat is installed in the vehicle, too much pre-load pressure will prevent the mat from being enabled. ISTA/P WILL NOT enable the new part, and will cause permanent damage to it."
Source components: AIR BAGS · AIR BAGS:SENSOR:OCCUPANT CLASSIFICATION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The vehicle position is missing or incorrect on the navigation map. The navigation system integrated in the Car Information Computer (CIC) is not calibrated correctly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Basic SVS: Voice Recognition Inoperative After Programming. After programming the vehicle with ISTA/P 2.48.x, the voice recognition (Basic SVS) is inoperative. NOTE: The Basic SVS only includes voice recognition for phone functions. Error in the coding data of ISTA/P 2.48.x The voice recognition function is unintentionally deactivated.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Advanced Onboard Battery Diagnostics. INFORMATION Starting with the introduction of the F10 (5 Series), an advanced intelligent battery sensor has been used. This now makes it possible for the vehicle to monitor the condition of the battery in order to determine if the battery needs to be recharged or replaced, along with the remaining capacity of the battery. The analysis and testing of the battery's SoC (State of Charge) and SoH (State of Health) is now performed using ISTA (Integrated Service Technical Application) diagnosis. A separate test using a battery tester is no longer needed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Retractable Hard Top (RHT) Is Not Stacking Properly - Frame Bent. The RHT frame is bent or twisted and cannot be operated in either direction, or the roof shells are not stacking properly. The hydraulic roof cylinders operate out of sequence causing the frame to twist.
NHTSA source summary · Original PDF not reviewed by Recallfolio
ncorrect Remaining Service Life from CBS Data for Brake pads. The calculated remaining service life for the brake pads (front and/or rear axle) from the CBS data does not match the actual brake pad thickness. The customer notices implausible remaining distances (too high or too low) on the front and/or the rear axle brake system. Software calculation in the brake pad wear model
NHTSA source summary · Original PDF not reviewed by Recallfolio
Service Action: Replace Coolant Expansion Tank. The low coolant level warning may come on in the information display. CAUSE Insufficient contact at the electrical connector for the coolant level sensor causes an inaccurate reading of the coolant level.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
One or more of the following situations may occur sporadically: * The vehicle does not start * The vehicle stops running * The air conditioning compressor does not turn on * Reverse lights do not work * The transmission does not shift into gear * Various chassis and engine check control messages CAUSE The ground point Z6000*4B on the engine block near the starter is loose.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
N55 Engine Failsafe - FC 120308 Boost Pressure Control, Plausibility: Pressure Too Low Stored in DME Fault Memory. INFORMATION The customer complains the SES is illuminated and the engine has reduced power (engine failsafe mode).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Service Action: Real Time Traffic Information Activation. The Real Time Traffic Information (RTTI) is inoperative. ??The traffic information icon is missing from the menu in the navigation map screen. CAUSE Option 6UH (RTTI) is missing from the Vehicle Order (VO).
NHTSA source summary · Original PDF not reviewed by Recallfolio
"After FEM Replacement, ISTA/P Unable to Read Vehicle Order. After the FEM (Front Electronic Module) is replaced, ISTA/P states ""The vehicle order could not be read from the vehicle. Import of the vehicle order required."" The replacement FEM does not contain the vehicle-specific data, including the Vehicle Order (VO). The proper ISTA/P parts replacement procedure was not performed."
NHTSA source summary · Original PDF not reviewed by Recallfolio
Advanced Onboard Battery Diagnostics. Starting with the introduction of the F10 (5 Series), an advanced intelligent battery sensor has been used. This now makes it possible for the vehicle to monitor the condition of the battery in order to determine if the battery needs to be recharged or replaced, along with the remaining capacity of the battery. The analysis and testing of the battery's SoC (Stateof Charge) and SoH (State of Health) is now performed using ISTA (Integrated Service Technical Application) diagnosis. A separate test using a battery tester is no longer needed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Front Seat Headrest Height Changes. The left or right front seat headrest can no longer be lowered to its lowest position, and is at a different height than before.