4014412018194
NHTSA communication ID: 10250665
NHTSA source summary · Original PDF not reviewed by Recallfolio
Shock absorber leaks: assessment aid
Source components: EQUIPMENT · STRUCTURE.
Source record 10250665 at NHTSAThe manufacturer’s record · Page 5 of 7
2010 Audi S4
Manufacturer communications & TSBs.Page 5
Original record summaries, dates and identifiers for this model-year. Records 401–500 of 681, ordered newest first. Dated records on this page: Oct 2, 2013–Jul 2, 2014.
Back to 2010 Audi S4 problems & recallsRead the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
4014402023187
NHTSA communication ID: 10250664
NHTSA source summary · Original PDF not reviewed by Recallfolio
Squeaking noises when steering or maneuvering
Source components: STEERING.
Source record 10250664 at NHTSAA401441 2018194-
NHTSA communication ID: 10122540
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 40 number 13-34 dated September 23, 2013. Oil appears on one or several shock absorbers.
Source components: SUSPENSION:FRONT:SHOCK ABSORBER · SUSPENSION:REAR:SHOCK ABSORBER.
Source record 10122540 at NHTSAA401440 2023187-
NHTSA communication ID: 10122539
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 40 number 13-35 dated September 23, 2013. Squeaking noises are heard when the steering wheel is turned or maneuvered. The noises may be more prevalent in wet weather. The folds of the outer rubber boots on the front axle shafts may come in contact with each other when the steering wheel is turned, causing squeaking noises. These noises are more likely to occur when the vehicle is new. The volume and occurrence of the noise will dissipate after a short break-in period.
Source components: STEERING: STEERING WHEEL/HANDLE BAR.
Source record 10122539 at NHTSAEdition92
NHTSA communication ID: 10231130
NHTSA source summary · Original PDF not reviewed by Recallfolio
Idenifying and mixing factory fill engine coolants
Source components: ENGINE AND ENGINE COOLING:COOLING SYSTEM.
Source record 10231130 at NHTSAA191450 2025303-
NHTSA communication ID: 10122415
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 19 number 13-41 dated June 20, 2013. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service.
Source components: ENGINE AND ENGINE COOLING.
Source record 10122415 at NHTSAEdition89
NHTSA communication ID: 10231127
NHTSA source summary · Original PDF not reviewed by Recallfolio
ElsaPro Software update and technical bulletins
Source components: ELECTRICAL SYSTEM:SOFTWARE · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10231127 at NHTSA37 13 07 2033658
NHTSA communication ID: 10212703
NHTSA source summary · Original PDF not reviewed by Recallfolio
Vehicle lacks power or will not move after stop due to simultaneous depressing of the brake and accelerator pedals
Source components: POWER TRAIN.
Source record 10212703 at NHTSA00146320335762
NHTSA communication ID: 10228295
NHTSA source summary · Original PDF not reviewed by Recallfolio
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. When an unapproved aftermarket speed-filling device is used to add oil to the engine, the increased oil flow rate may force oil into the intake manifold or combustion chamber, creating the potential for engine damage.
Source components: ENGINE AND ENGINE COOLING.
Source record 10228295 at NHTSA37143020036586
NHTSA communication ID: 10226529
NHTSA source summary · Original PDF not reviewed by Recallfolio
Vehicle lacks power or will not move after stop due to simultaneous depressing of the brake and accelerator pedals
Source components: POWER TRAIN.
Source record 10226529 at NHTSA00146320335762
NHTSA communication ID: 10221947
NHTSA source summary · Original PDF not reviewed by Recallfolio
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. When an unapproved aftermarket speed-filling device is used to add oil to the engine, the increased oil flow rate may force oil into the intake manifold or combustion chamber, creating the potential for engine damage.
Source components: ENGINE AND ENGINE COOLING.
Source record 10221947 at NHTSA37 14 30 2003658
NHTSA communication ID: 10210679
NHTSA source summary · Original PDF not reviewed by Recallfolio
This condition may be caused when the brake pedal and the accelerator pedal are depressed simultaneously. Drivers who drive with their left foot resting on the brake pedal are prone to experience this condition. With the introduction of Electronic Power Control (EPC) (no accelerator cable) to fuel injection systems, an engine RPM control feature has been incorporated into the engine electronic control system software. Customer states that the engine returns to idle speed of approximately 1,400 RPM although the accelerator is depressed, and/or the vehicle hesitates (lacks power on take-off).
Source components: ELECTRONIC STABILITY CONTROL (ESC):CONTROL MODULE:SOFTWARE · POWER TRAIN.
Source record 10210679 at NHTSAA371430 2003658-
NHTSA communication ID: 10122465
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 37 number 13-07 dated May 29, 2013. Customer states that the engine returns to idle speed of approximately 1,400 RPM although the accelerator is depressed, and/or the vehicle hesitates (lacks power on take-off). No DTCs are stored. This condition may be caused when the brake pedal and the accelerator pedal are depressed simultaneously. Drivers who drive with their left foot resting on the brake pedal are prone to experience this condition.
Source components: POWER TRAIN:CLUTCH ASSEMBLY:PEDAL/HAND LEVER(MOTORCYCLE).
Source record 10122465 at NHTSAA001463 2033576-
NHTSA communication ID: 10122452
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 00 number 13-49 dated May 14, 2013. Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. When an unapproved aftermarket speed-filling device is used to add oil to the engine, the increased oil flow rate may force oil into the intake manifold or combustion chamber, creating the potential for engine damage.
Source components: ENGINE · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10122452 at NHTSAEdition87
NHTSA communication ID: 10231139
NHTSA source summary · Original PDF not reviewed by Recallfolio
Technical bulletins and updates
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10231139 at NHTSA441450202256310
NHTSA communication ID: 10250971
NHTSA source summary · Original PDF not reviewed by Recallfolio
Steering wheel shimmy, vibration, and/or oscillation
Source components: STEERING.
Source record 10250971 at NHTSAA441450 2022563-
NHTSA communication ID: 10122467
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 44 number 14-49 dated April 17, 2014. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. The customer feels the vibration while driving at highway speeds from 55 ? 80 mph (88 ? 128 km/h). This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. If an applicable Repair Authorization is not followed, the claim will not be paid. The vibrations felt by the customer could be a result of the harmonic vibrations caused by the radial force variation (RFV) of the tires or an imbalance of the wheel and tire assembly.
Source components: STEERING: STEERING WHEEL/HANDLE BAR · SUSPENSION.
Source record 10122467 at NHTSAUpdate91i8
NHTSA communication ID: 10249085
NHTSA source summary · Original PDF not reviewed by Recallfolio
Google Maps Street View (NVLW))
Source components: UNKNOWN OR OTHER.
Source record 10249085 at NHTSA35 14 16 2027363
NHTSA communication ID: 10212689
NHTSA source summary · Original PDF not reviewed by Recallfolio
Drivability concerns, S tronic transmission
Source components: EQUIPMENT ADAPTIVE/MOBILITY · POWER TRAIN:MANUAL TRANSMISSION.
Source record 10212689 at NHTSA35 14 16 2027363
NHTSA communication ID: 10210636
NHTSA source summary · Original PDF not reviewed by Recallfolio
One or multiple transmission-related concerns may be present, including:
Source components: POWER TRAIN:MANUAL TRANSMISSION.
Source record 10210636 at NHTSAA351416 2027363-
NHTSA communication ID: 10122456
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 35 number 13-11 dated June 11, 2013. One or multiple transmission-related concerns may be present. Harsh downshifting of multiple gears: 7-5, 4-3, 2-1. This may happen during just one of these shifts. A bump is felt after vehicle comes to a stop (2-1 downshift). Fluctuating engine speed after 5-4 shift with accelerator at 80-100% accelerator pedal position (kick-down). The driver information system displays the message "Gearbox complaint! Journey can be continued." After a key cycle the complaint is fixed. The vehicle was parked in gear lever position N and the ignition switched off. DTC P1724 (signal for immobilizer, short circuit to ground) is logged in the transmission control module, J217 (address word 02). Incorrect transmission software.
Source components: ELECTRICAL SYSTEM · POWER TRAIN:AUTOMATIC TRANSMISSION:GEAR POSITION INDICATION (PRNDL).
Source record 10122456 at NHTSA2027363/3
NHTSA communication ID: 10065987
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
Source components: ELECTRICAL SYSTEM:SOFTWARE.
Source record 10065987 at NHTSA24ASUPDATE
NHTSA communication ID: 10249097
NHTSA source summary · Original PDF not reviewed by Recallfolio
ECM Software Update (FED_EMS)
Source components: ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM) · ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM):SOFTWARE.
Source record 10249097 at NHTSAUpdate24AS
NHTSA communication ID: 10249049
NHTSA source summary · Original PDF not reviewed by Recallfolio
ECM Software Update
Source components: ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM) · ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM):SOFTWARE.
Source record 10249049 at NHTSADealer Letter -
NHTSA communication ID: 10122377
NHTSA source summary · Original PDF not reviewed by Recallfolio
This communication is to inform you of upcoming Update 24AS. On Audi vehicles manufactured within a specific period the ECM software needs to be updated to address customer complaints of driveability and rough idle.
Source components: ELECTRICAL SYSTEM:SOFTWARE · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
Source record 10122377 at NHTSA24AS
NHTSA communication ID: 10067650
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
Source components: ELECTRICAL SYSTEM:SOFTWARE.
Source record 10067650 at NHTSA44144920225639
NHTSA communication ID: 10250982
NHTSA source summary · Original PDF not reviewed by Recallfolio
Steering wheel shimmy, vibration, and/or oscillation
Source components: STEERING.
Source record 10250982 at NHTSAA441449 2022563-
NHTSA communication ID: 10122338
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 44 number 13-44 dated November 21, 2013. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. The customer feels the vibration while driving at highway speeds from 55 - 80 mph (88 - 128 km/h). This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. If an applicable Repair Authorization is not followed, the claim will not be paid. The vibrations felt by the customer could be a result of the harmonic vibrations caused by the radial force variation (RFV) of the tires or an imbalance of the wheel and tire assembly. Tires with higher mileage and/or wear should be inspected to determine the best correction for the issue (repair or replacement). Tire life and condition should be determined prior to starting any diagnosis or repair for a vibration.
Source components: SUSPENSION.
Source record 10122338 at NHTSAA911437 2030947-
NHTSA communication ID: 10122359
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 91 number 13-92 dated July 16, 2013. The customer complains that when he or she is trying to place a phone call from the vehicle while using a Bluetooth®-connected phone, the phone call disconnects before it begins and an error shows on the MMI display. The message may be "Function not supported" or "Network error". The customer is using a phone with the Android operating system. In addition, Skype®, or another network-based communication software, is installed on the phone. Call can be placed directly from the phone without a problem. When the phone receives the request to place a call from the vehicle, a prompt appears on the phone asking the user to choose how the call should be placed. If the prompt is ignored, the MMI system disconnects the call because it assumes that the phone is not responding.
Source components: ELECTRICAL SYSTEM:SOFTWARE · EQUIPMENT:ELECTRICAL.
Source record 10122359 at NHTSAA911435 2026895-
NHTSA communication ID: 10122357
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 91 number 14-19 dated January 3, 2014. Customer complains that during Bluetooth calls, the person at the other end has trouble hearing the speaker in the vehicle. Voice recognition accuracy is poor. This TSB provides guidelines for testing microphones in a vehicle.
Source components: EQUIPMENT:ELECTRICAL.
Source record 10122357 at NHTSAEdition75
NHTSA communication ID: 10231131
NHTSA source summary · Original PDF not reviewed by Recallfolio
Technical bulletins and updates
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10231131 at NHTSA144920284402
NHTSA communication ID: 10216651
NHTSA source summary · Original PDF not reviewed by Recallfolio
The customer complains of one or more of the following issues: ? When the vehicle is completely refueled, the vehicle range (?distance to empty?) that is displayed is different than the vehicle range that was displayed the last time the vehicle was completely refueled. ? The displayed vehicle range drops inconsistently. ? After the vehicle is refueled, the displayed vehicle range does not change for a long period of time. ? When the vehicle is driven on hilly roads for a long period of time, the displayed vehicle range suddenly changes by a significant amount. ? There are no DTCs related to fuel senders stored in the instrument cluster control module, J285 (address word 17). This condition does not involve or affect the accuracy of the fuel level indicator, but only the estimated distance to empty display on the on-board computer.
Source components: BACK OVER PREVENTION:DISPLAY FUNCTION.
Source record 10216651 at NHTSAA171449 2028440-
NHTSA communication ID: 10122332
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 17 number 12-26 dated January 20, 2012. When the vehicle is completely refueled, the vehicle range (?distance to empty?) that is displayed is different than the vehicle range that was displayed the last time the vehicle was completely refueled. The displayed vehicle range drops inconsistently. After the vehicle is refueled, the displayed vehicle range does not change for a long period of time. When the vehicle is driven on hilly roads for a long period of time, the displayed vehicle range suddenly changes by a significant amount. There are no DTCs related to fuel senders stored in the instrument cluster control module, J285 (address word 17). This condition does not involve or affect the accuracy of the fuel level indicator, but only the estimated distance to empty display on the on-board computer.
Source components: ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL.
Source record 10122332 at NHTSAEdition79
NHTSA communication ID: 10231135
NHTSA source summary · Original PDF not reviewed by Recallfolio
Technical bulletins and updates
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10231135 at NHTSAA691428 2023323-
NHTSA communication ID: 10122295
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 69 number 13-26 dated October 21, 2013. After the airbag control module (J234) has been replaced, the control unit cannot be coded via SVM spec/actual. An SVM code is required to code and parameterize the new service replacement airbag control module. Each model's SVM code is provided in a parts bulletin (GP bulletin), which should have been referenced through ETKA when the module was replaced. The control module cannot be coded until the SVM code has been executed. If the SVM code was not acquired through the GP bulletin in ETKA, follow the instructions in the Service section of this bulletin to update the control module.
Source components: AIR BAGS · AIR BAGS:FRONTAL:SENSOR/CONTROL MODULE-INACTIVE.
Source record 10122295 at NHTSAA911429 2026888-
NHTSA communication ID: 10122302
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 91 number 12-50 dated August 1, 2012. Echo effects, caller on either end cannot hear conversation, sound distortion or feedback, and the sound is distorted, hisses, or scrapes occur during a phone call. This bulletin provides guidelines for analyzing the call quality of the Bluetooth system in the vehicle, and is not applicable to any Audi warranty.
Source components: EQUIPMENT:ELECTRICAL.
Source record 10122302 at NHTSA147320314585
NHTSA communication ID: 10216611
NHTSA source summary · Original PDF not reviewed by Recallfolio
Under extreme driving conditions (such as short-distance, stop-and-go driving), high crankcase pressure can cause the DTCs to appear. The condition can be improved and the DTCs eliminated when the crankcase pressure valve is changed to a lower operating pressure and the ECM software is updated to compensate for new crankcase pressure.
Source components: SERVICE BRAKES.
Source record 10216611 at NHTSAA011473 2031458-
NHTSA communication ID: 10122281
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 01 number 13-45 dated December 5, 2013. The MIL is on. DTCs are stored in the ECM. Under extreme driving conditions (such as short-distance, stop-and-go driving), high crankcase pressure can cause the DTCs to appear. The condition can be improved and the DTCs eliminated when the crankcase pressure valve is changed to a lower operating pressure and the ECM software is updated to compensate for new crankcase pressure.
Source components: ENGINE AND ENGINE COOLING · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV).
Source record 10122281 at NHTSAEdition77
NHTSA communication ID: 10231133
NHTSA source summary · Original PDF not reviewed by Recallfolio
Technical bulletins and updates
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10231133 at NHTSA46147320276367
NHTSA communication ID: 10250988
NHTSA source summary · Original PDF not reviewed by Recallfolio
squealing from front brakes (PR-1LJ)
Source components: SERVICE BRAKES, HYDRAULIC.
Source record 10250988 at NHTSA2027636/7
NHTSA communication ID: 10066930
NHTSA source summary · Original PDF not reviewed by Recallfolio
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
Source components: SERVICE BRAKES.
Source record 10066930 at NHTSA96148220363441
NHTSA communication ID: 10226435
NHTSA source summary · Original PDF not reviewed by Recallfolio
96 Alarm sounds when driver door is unlocked with mechanical key
Source components: EQUIPMENT:ELECTRICAL:ANTI-THEFT DEVICES.
Source record 10226435 at NHTSAA961482 2036344-
NHTSA communication ID: 10122306
NHTSA source summary · Original PDF not reviewed by Recallfolio
The vehicle's anti-theft alarm sounds when the driver door is unlocked with a mechanical key. No DTCs are stored. The keyless remote was not used to unlock the vehicle. In order to minimize current draw after the ignition has been turned off, the electronics system of the vehicle goes into sleep mode. During this time, each module monitors the CAN bus more slowly than when the electronics system is awake. Because the system is being monitored more slowly, there is a delay in the waking of the central locking system. This delay causes a delay in the disabling of the anti-theft alarm system when the manual key is used. If the key is turned in less than a quarter of a second, the system can unlock the vehicle even though the anti-theft alarm has not been disabled.
Source components: EQUIPMENT:ELECTRICAL:ANTI-THEFT DEVICES · LATCHES/LOCKS/LINKAGES:DOORS:LATCH.
Source record 10122306 at NHTSAA871447 2010146-
NHTSA communication ID: 10125561
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 87 number 12-27 dated April 24, 2012. There is an unpleasant, musty odor coming from the heating and ventilation system. The odor usually occurs when the vehicle has been sitting unused for five hours or more. The odor usually occurs within 20 to 60 seconds after the vehicle is started. Condensation, which is a normal condition in all A/C systems, can cause a musty odor. If the odor is noticeable in the vehicle when the engine is not turned on, the cause may be mold and mildew in the passenger compartment, and not be related to the A/C system. All other possible sources of the odor must be investigated before this bulletin can be performed.
Source components: EQUIPMENT:APPLIANCE:AIR CONDITIONER.
Source record 10125561 at NHTSA00145920297372
NHTSA communication ID: 10228292
NHTSA source summary · Original PDF not reviewed by Recallfolio
When oil is drained through the drain plug, the oil might spill on components around the oil pan area. If it is not properly cleaned up, this spilled oil could drip after the procedure is complete, causing unnecessary customer complaints.
Source components: ENGINE AND ENGINE COOLING.
Source record 10228292 at NHTSA00145920297372
NHTSA communication ID: 10221944
NHTSA source summary · Original PDF not reviewed by Recallfolio
When oil is drained through the drain plug, the oil might spill on components around the oil pan area. If it is not properly cleaned up, this spilled oil could drip after the procedure is complete, causing unnecessary customer complaints.
Source components: ENGINE AND ENGINE COOLING.
Source record 10221944 at NHTSAA001459 2029737-
NHTSA communication ID: 10125536
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 00 number 12-34 dated June 6, 2012. The process of draining oil through the drain plug is not always tidy. When oil is drained through the drain plug, the oil might spill on components around the oil pan area. If it is not properly cleaned up, this spilled oil could drip after the procedure is complete, causing unnecessary customer complaints.
Source components: ELECTRICAL SYSTEM.
Source record 10125536 at NHTSAA461473 2027636-
NHTSA communication ID: 10122289
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 46 number 13-41 dated June 11, 2013. Brakes on vehicles produced before September 3, 2012 (calendar week 36 of 2012), squeak or squeal when used with light to moderate force.
Source components: SERVICE BRAKES.
Source record 10122289 at NHTSAA451408 2033412-
NHTSA communication ID: 10125535
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 45 number 13-07 dated September 25, 2013. Steering wheel does not lock. Various warning lights are on. Steering feels stiffer than usual. The engine cannot be switched off. The ignition key cannot be removed. There are DTC entries present in the system (either static or sporadic). DTCs with description ?Brake control module - no signal/communication? are present in several control units. DTCs are stored in the ABS control module. This condition does not result in any drivability concerns. The steering system is fully connected. The insulation for the ABS wheel speed sensor is damaged in production. Over time, this can lead to corrosion on the wires and restricted functions with the ABS control module. Only the wires in the left bulkhead grommet are affected.
Source components: ELECTRICAL SYSTEM · STEERING.
Source record 10125535 at NHTSATSB-45-13-07
NHTSA communication ID: 10054858
NHTSA source summary · Original PDF not reviewed by Recallfolio
AUDI: DUE TO DAMAGE ABS WHEEL SPEED SENSOR DURING PRODUCTION, SOME VEHICLES MAY EXPERIENCE STEERING WHEEL NOT LOCKING, IGNITION KEY CANNOT BE REMOVED, AND OTHER VARIOUS ISSUES. MODEL 2009-2014 A4/S4, A5/S5, A5/S5 CAB, Q5. *PE UPDATED 05/21/2014 *JS
Source components: SERVICE BRAKES, AIR:ANTILOCK:ABS WARNING LIGHT · SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP:ABS WARNING LIGHT.
Source record 10054858 at NHTSAA481457 2034351-
NHTSA communication ID: 10122194
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 48 number 13-47 dated August 2, 2013. Customer may report hearing creaking or squeaking noise from the steering column when steering slowly (the noise can be duplicated while the vehicle is stationary if the steering wheel is turned slowly). The noise may get louder at higher temperatures or when the vehicle is driven for a longer period of time. The noise comes from the sealing sleeve/steering column opening on the bulkhead. Listen to the attached audio file for example of the noise. Insufficient lubrication of the intermediate steering shaft in the area of the sealing sleeve.
Source components: STEERING · WHEELS.
Source record 10122194 at NHTSAEdition69
NHTSA communication ID: 10231122
NHTSA source summary · Original PDF not reviewed by Recallfolio
Technical bulletins and updates
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10231122 at NHTSAA461466 2022584-
NHTSA communication ID: 10122192
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 46 number 12-23 dated June 18, 2012. Customer may report that the steering wheel vibrates or pulsates when the brakes are applied. Document contains the brake pulsation diagnostic guidelines.
Source components: SERVICE BRAKES, HYDRAULIC · STEERING · WHEELS.
Source record 10122192 at NHTSAA911419 2026895-
NHTSA communication ID: 10122199
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 91 number 11-16 dated October 5, 2011. During a Bluetooth call, the sound is difficult to hear for the other party. Voice recognition accuracy is poor. This TSB provides guidelines for testing microphones in a vehicle.
Source components: ELECTRICAL SYSTEM.
Source record 10122199 at NHTSA01134920354542
NHTSA communication ID: 10228344
NHTSA source summary · Original PDF not reviewed by Recallfolio
Under certain driving conditions, the secondary air ports in the cylinder head can accumulate carbon over time, causing a restriction. The ODIS tester can identify the state of the restriction, and will request that the system is cleaned in order to prevent the MIL from illuminating.
Source components: ENGINE AND ENGINE COOLING.
Source record 10228344 at NHTSA01134820330015
NHTSA communication ID: 10228343
NHTSA source summary · Original PDF not reviewed by Recallfolio
Under certain driving conditions, the secondary air ports in the cylinder head can accumulate carbon over time, causing a restriction.
Source components: ENGINE AND ENGINE COOLING.
Source record 10228343 at NHTSA01134920354542
NHTSA communication ID: 10225023
NHTSA source summary · Original PDF not reviewed by Recallfolio
Under certain driving conditions, the secondary air ports in the cylinder head can accumulate carbon over time, causing a restriction. The ODIS tester can identify the state of the restriction, and will request that the system is cleaned in order to prevent the MIL from illuminating.
Source components: ENGINE AND ENGINE COOLING.
Source record 10225023 at NHTSA01134820330015
NHTSA communication ID: 10225022
NHTSA source summary · Original PDF not reviewed by Recallfolio
Under certain driving conditions, the secondary air ports in the cylinder head can accumulate carbon over time, causing a restriction.
Source components: ENGINE AND ENGINE COOLING.
Source record 10225022 at NHTSA01134920354542
NHTSA communication ID: 10221996
NHTSA source summary · Original PDF not reviewed by Recallfolio
Under certain driving conditions, the secondary air ports in the cylinder head can accumulate carbon over time, causing a restriction. The ODIS tester can identify the state of the restriction, and will request that the system is cleaned in order to prevent the MIL from illuminating.
Source components: ENGINE AND ENGINE COOLING.
Source record 10221996 at NHTSA01134820330015
NHTSA communication ID: 10221995
NHTSA source summary · Original PDF not reviewed by Recallfolio
Under certain driving conditions, the secondary air ports in the cylinder head can accumulate carbon over time, causing a restriction.
Source components: ENGINE AND ENGINE COOLING.
Source record 10221995 at NHTSAA011349 2035454-
NHTSA communication ID: 10121402
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 01 number 13-35 dated October 8, 2013. During reset of the service reminder, the message ?AIR system - action required - observe test plan? appears on the ODIS tester. MIL is not illuminated. Under certain driving conditions, the secondary air ports in the cylinder head can accumulate carbon over time, causing a restriction. The ODIS tester can identify the state of the restriction, and will request that the system is cleaned in order to prevent the MIL from illuminating.
Source components: ELECTRICAL SYSTEM.
Source record 10121402 at NHTSAA011348 2033001-
NHTSA communication ID: 10121401
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 01 number 13-37 dated October 10, 2013. MIL on. DTCs are stored in the engine control module. Mileage is greater than 15,000 miles. Under certain driving conditions, the secondary air ports in the cylinder head can accumulate carbon over time, causing a restriction.
Source components: ENGINE.
Source record 10121401 at NHTSA44134620103345
NHTSA communication ID: 10251027
NHTSA source summary · Original PDF not reviewed by Recallfolio
Tightening wheel bolts
Source components: WHEELS.
Source record 10251027 at NHTSAA441346 2010334-
NHTSA communication ID: 10121408
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 44 number 12-32 dated August 2, 2012. Wheel bolt requires torque adjustment. Torque sticks, torque extension bars, and impact guns/wrenches are not approved by Audi of America, Inc., and should not be used to apply torque to wheel bolts. Always use a calibrated torque wrench to attain the correct wheel bolt torque and follow the proper wheel tightening procedure as outlined in Elsa. Proper use of a calibrated torque wrench ensures that all wheel bolts are tightened equally and reduces the chances of repeat repairs. Using methods other than a calibrated torque wrench to attain correct wheel bolt torque may lead to problems.
Source components: WHEELS · WHEELS:LUGS/NUTS/BOLTS/STUDS.
Source record 10121408 at NHTSATSB-44-13-46
NHTSA communication ID: 10054859
NHTSA source summary · Original PDF not reviewed by Recallfolio
AUDI: ON CERTAIN VEHICLES, USE CALIBRATED TORQUE WRENCH AND NOT TORQUE STICKS, TORQUE EXTENSION BARS AND IMPACT GUNS/WRENCHES NOT APPROVED FOR USAGE ON WHEEL BOLTS BY MANUFACTURER, THAT CAN CAUSE DAMAGE TO BRAKE, STEERING WHEEL, HUB. MODEL 1995-2014 ALL. *PE
Source components: EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10054859 at NHTSASB-48326
NHTSA communication ID: 10053944
NHTSA source summary · Original PDF not reviewed by Recallfolio
AUDI: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. INFORMATION PROVIDED REGARDING WARRANTY EXTENSION ON CARBON BUILDUP REMOVAL, ENGINE CYLINDER HEAD SECONDARY AIR PORTS. MODELS 2009-2012. NO MODEL PROVIDED. *PE
Source components: ENGINE.
Source record 10053944 at NHTSA01134520314584
NHTSA communication ID: 10228340
NHTSA source summary · Original PDF not reviewed by Recallfolio
Under extreme driving conditions (such short-distance, stop-and-go driving), high crankcase pressure can cause the DTCs to appear.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV).
Source record 10228340 at NHTSA01134520314584
NHTSA communication ID: 10225019
NHTSA source summary · Original PDF not reviewed by Recallfolio
Under extreme driving conditions (such short-distance, stop-and-go driving), high crankcase pressure can cause the DTCs to appear.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV).
Source record 10225019 at NHTSA01134520314584
NHTSA communication ID: 10221992
NHTSA source summary · Original PDF not reviewed by Recallfolio
Under extreme driving conditions (such short-distance, stop-and-go driving), high crankcase pressure can cause the DTCs to appear.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV).
Source record 10221992 at NHTSAA011345 2031458-
NHTSA communication ID: 10121398
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 01 number 13-66 dated January 17, 2013. MIL on. DTCs are stored in the engine control module (ECM). Under extreme driving conditions (such short-distance, stop-and-go driving), high crankcase pressure can cause the DTCs to appear. The condition can be improved and the DTCs eliminated when the crankcase pressure valve is changed to a lower operating pressure and the ECM software is updated to compensate for new crankcase pressure.
Source components: ENGINE.
Source record 10121398 at NHTSA3513152030477 6
NHTSA communication ID: 10204487
NHTSA source summary · Original PDF not reviewed by Recallfolio
The following message appears in the information display: ?Gearbox malfunction: you can continue driving?.
Source components: POWER TRAIN.
Source record 10204487 at NHTSA44134420225638
NHTSA communication ID: 10251025
NHTSA source summary · Original PDF not reviewed by Recallfolio
Steering wheel shimmy, vibration and/or oscillation
Source components: STEERING.
Source record 10251025 at NHTSA4413442022563 8
NHTSA communication ID: 10204489
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel.
Source components: STEERING · SUSPENSION · TIRES · WHEELS.
Source record 10204489 at NHTSAA441344 2022563-
NHTSA communication ID: 10121497
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 44 number 13-42 dated September 27, 2013. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. The customer feels the vibration while driving at highway speeds from 55 - 80 mph (88 - 128 km/h). This bulletin is not applicable if this vehicle has a Repair Authorization on this topic.
Source components: STEERING · SUSPENSION.
Source record 10121497 at NHTSAEdition62
NHTSA communication ID: 10243771
NHTSA source summary · Original PDF not reviewed by Recallfolio
Audi Elsa Newsletter
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10243771 at NHTSAAudi Newsletter
NHTSA communication ID: 10204516
NHTSA source summary · Original PDF not reviewed by Recallfolio
Wind noise from Exterior Mirror.
Source components: VISIBILITY:REARVIEW MIRRORS/DEVICES.
Source record 10204516 at NHTSA9113142013790 8
NHTSA communication ID: 10204503
NHTSA source summary · Original PDF not reviewed by Recallfolio
The navigation DVD or other CD/DVD cannot be ejected.
Source components: EQUIPMENT:ELECTRICAL.
Source record 10204503 at NHTSAA911314 2013790-
NHTSA communication ID: 10121511
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 91 number 11-25 dated November 29, 2011. The navigation DVD or other CD/DVD cannot be ejected. There are no DTCs stored in the corresponding module. The eject button is not stuck. When the eject button is pushed, the drive does not sound as if it is trying to eject the CD/DVD. Vehicles with DVD-based navigation systems now have the navigation DVD installed during production. To prevent theft of the DVD during transportation, the eject button of the navigation drive is disabled. The navigation system itself (e.g., route guidance) functions as specified. The eject buttons of vehicles without DVD-based navigation systems are not disabled during production, but could behave as described in the Condition section of this bulletin. The eject button can be enabled through Guided Fault Finding.
Source components: EQUIPMENT:ELECTRICAL · EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM).
Source record 10121511 at NHTSAEdition60
NHTSA communication ID: 10243769
NHTSA source summary · Original PDF not reviewed by Recallfolio
Audi Elsa Newsletter
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10243769 at NHTSA35 13 15 2030477
NHTSA communication ID: 10212688
NHTSA source summary · Original PDF not reviewed by Recallfolio
Gearbox malfunction message in cluster.
Source components: ELECTRICAL SYSTEM · POWER TRAIN:MANUAL TRANSMISSION.
Source record 10212688 at NHTSA35 13 15 2030477
NHTSA communication ID: 10210698
NHTSA source summary · Original PDF not reviewed by Recallfolio
The following message appears in the information display: ?Gearbox malfunction: you can continue driving.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:GEAR POSITION INDICATION (PRNDL).
Source record 10210698 at NHTSAAudi Newsletter
NHTSA communication ID: 10204514
NHTSA source summary · Original PDF not reviewed by Recallfolio
Several weeks ago, the ODIS Quick Reference Guide was sent to all dealer technicians (non-corporate
Source components: EQUIPMENT.
Source record 10204514 at NHTSAA351315 2030477-
NHTSA communication ID: 10121495
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 35 number 13-14 dated August 30, 2013. Message appears in the information display: "Gearbox malfunction: you can continue driving". One or more fault entries are stored in the transmission control module. Fault codes and symptom codes must match exactly or this TSB should not be followed. Instructions for obtaining the symptom codes are in the Service section of this bulletin. Poor internal contact area on circuit board will lead to faults. Oil additives can cause the plastic circuit plates to delaminate, causing contact loss.
Source components: POWER TRAIN · STEERING:GEAR BOX (OTHER THAN RACK AND PINION).
Source record 10121495 at NHTSATSB-35-13-15
NHTSA communication ID: 10054213
NHTSA source summary · Original PDF not reviewed by Recallfolio
AUDI: MULTIPLE DIAGNOSTIC TROUBLE CODES (DTC) ASSOCIATED WITH POOR INTERNAL CONTACT OF CIRCUIT BOARD (GEARBOX) WHERE OIL ADDITIVES CAN CAUSE PLASTIC CIRCUIT PLATES TO DELAMINATE AND CONTACT LOSS. MODEL 2010-2013 S4, S5, RS5, S6, S7. *PE
Source components: STEERING:GEAR BOX (OTHER THAN RACK AND PINION).
Source record 10054213 at NHTSAReference-Oil Ca
NHTSA communication ID: 10121987
NHTSA source summary · Original PDF not reviewed by Recallfolio
This document contains the Audi oil capacity chart.
Source components: ENGINE · EQUIPMENT · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10121987 at NHTSAEdition58
NHTSA communication ID: 10243775
NHTSA source summary · Original PDF not reviewed by Recallfolio
Audi Elsa Newsletter
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10243775 at NHTSAA871346 2035582-
NHTSA communication ID: 10121947
NHTSA source summary · Original PDF not reviewed by Recallfolio
The A/C Compressor has been diagnosed as faulty and will be replaced under warranty. When performing replacement of an A/C Compressor under warranty, the amount of refrigerant and oil recovered must be documented.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT:APPLIANCE:AIR CONDITIONER.
Source record 10121947 at NHTSAA691326 2023323-
NHTSA communication ID: 10121316
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 69 number 12-25 dated April 25, 2012. After the airbag control module (J234) has been replaced, the control unit cannot be coded via SVM spec/actual. An SVM code is required to code and parameterize the new service replacement airbag control module. Each model?s SVM code is provided in a parts bulletin (GP bulletin), which should have been referenced through ETKA when the module was replaced. The control module cannot be coded until the SVM code has been executed.
Source components: AIR BAGS · ELECTRICAL SYSTEM.
Source record 10121316 at NHTSA01133720330014
NHTSA communication ID: 10228332
NHTSA source summary · Original PDF not reviewed by Recallfolio
Under certain driving conditions, the secondary air ports in the cylinder head can accumulate carbon over time, causing a restriction.
Source components: ENGINE AND ENGINE COOLING.
Source record 10228332 at NHTSA01133720330014
NHTSA communication ID: 10225011
NHTSA source summary · Original PDF not reviewed by Recallfolio
Under certain driving conditions, the secondary air ports in the cylinder head can accumulate carbon over time, causing a restriction.
Source components: ENGINE AND ENGINE COOLING.
Source record 10225011 at NHTSA01133720330014
NHTSA communication ID: 10221984
NHTSA source summary · Original PDF not reviewed by Recallfolio
Under certain driving conditions, the secondary air ports in the cylinder head can accumulate carbon over time, causing a restriction.
Source components: ENGINE AND ENGINE COOLING.
Source record 10221984 at NHTSAA011337 2033001-
NHTSA communication ID: 10121297
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 01 number 13-24 dated August 20, 2013. MIL on. DTCs are stored in the engine control module. Mileage is greater than 15,000 miles. Under certain driving conditions, the secondary air ports in the cylinder head can accumulate carbon over time, causing a restriction.
Source components: ENGINE.
Source record 10121297 at NHTSA01133520354541
NHTSA communication ID: 10228330
NHTSA source summary · Original PDF not reviewed by Recallfolio
During reset of the service reminder, the following message appears on the ODIS tester: ?Secondary air injection system - checking secondary air mass?. Under certain driving conditions, the secondary air ports in the cylinder head can accumulate carbon over time, causing a restriction. The ODIS tester can identify the state of the restriction, and will request that the system is cleaned in order to prevent the MIL from illuminating.
Source components: ENGINE AND ENGINE COOLING.
Source record 10228330 at NHTSA01133520354541
NHTSA communication ID: 10225009
NHTSA source summary · Original PDF not reviewed by Recallfolio
During reset of the service reminder, the following message appears on the ODIS tester: ?Secondary air injection system - checking secondary air mass?. Under certain driving conditions, the secondary air ports in the cylinder head can accumulate carbon over time, causing a restriction. The ODIS tester can identify the state of the restriction, and will request that the system is cleaned in order to prevent the MIL from illuminating.
Source components: ENGINE AND ENGINE COOLING.
Source record 10225009 at NHTSA01133520354541
NHTSA communication ID: 10221982
NHTSA source summary · Original PDF not reviewed by Recallfolio
During reset of the service reminder, the following message appears on the ODIS tester: ?Secondary air injection system - checking secondary air mass?. Under certain driving conditions, the secondary air ports in the cylinder head can accumulate carbon over time, causing a restriction. The ODIS tester can identify the state of the restriction, and will request that the system is cleaned in order to prevent the MIL from illuminating.
Source components: ENGINE AND ENGINE COOLING.
Source record 10221982 at NHTSAA011335 2035454-
NHTSA communication ID: 10121295
NHTSA source summary · Original PDF not reviewed by Recallfolio
During reset of the service reminder, the following message appears on the ODIS tester: ?Secondary air injection system - checking secondary air mass?. MIL is not illuminated. Under certain driving conditions, the secondary air ports in the cylinder head can accumulate carbon over time, causing a restriction. The ODIS tester can identify the state of the restriction, and will request that the system is cleaned in order to prevent the MIL from illuminating.
Source components: EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10121295 at NHTSAEdition56
NHTSA communication ID: 10243773
NHTSA source summary · Original PDF not reviewed by Recallfolio
Audi Elsa Newsletter
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10243773 at NHTSA27 13 19 2029010
NHTSA communication ID: 10212668
NHTSA source summary · Original PDF not reviewed by Recallfolio
Low battery charge: excess current draw location
Source components: ELECTRICAL SYSTEM:12V/24V/48V BATTERY.
Source record 10212668 at NHTSAA271319 2029010-
NHTSA communication ID: 10121306
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 27 number 12-13 dated March 22, 2012. The customer may report a discharged battery when trying to start the vehicle. The condition results in a no start.
Source components: ELECTRICAL SYSTEM:12V/24V/48V BATTERY.
Source record 10121306 at NHTSA741312 2004327-4
NHTSA communication ID: 10121945
NHTSA source summary · Original PDF not reviewed by Recallfolio
Supersedes Technical Service Bulletin Group 70 number 08-39 dated December 4, 2008. Leather upholstery is dirty or stained.
Source components: EQUIPMENT · STRUCTURE.
Source record 10121945 at NHTSA