Original record summaries, dates and identifiers for this model-year. Records 401–500 of 856, ordered newest first. Dated records on this page: Jul 28, 2014–Jun 19, 2015.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Jun 19, 2015Service Bulletin/Repair Instructions
TT 21-10-02
NHTSA communication ID: 10122981
NHTSA source summary · Original PDF not reviewed by Recallfolio
Tech Tips: The document discusses the conditions of when turbo can to be fixed or replaced
Source components: ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Tech Tips (Coolant Leak or Repeat Coolant Leak from the Water Pump Area): The document informs to inspect for issues, and why issues may happen. It also notes how to fix the issue, and other issues that could happen while repairing the issue
NHTSA source summary · Original PDF not reviewed by Recallfolio
Tech Tips (Radiator Identification Sensor): On TSI (2.0l CCTA, CBFA) equipped vehicles with fault code P2568 Direct Ozone Reduction Catalyst Temperature Sensor, this fault refers to - G611- as Radiator Identification Sensor. If the radiator requires replacement on any above listed vehicle, the -G611- will be packaged separately within the radiator packaging. The new sensor will need to be bonded to the radiator.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Technical Bulletin (Sunroof or Power Sunshade, Does Not Open/Close or Automatic Operation Does Not Function). This document contains Warranty information for coverage, and informs of methods to to service the issue
NHTSA source summary · Original PDF not reviewed by Recallfolio
Tech Tips (Heated Rear Window, One or More Lines Inoperative): To detect which line(s) is inoperative, utilize a volt meter to check for 0 V, which will be present after the open in the grid line. The check must be performed with the engine running and heated rear window switched on. Switch OFF the ignition and visually locate the damage.
Source components: ELECTRICAL SYSTEM · VISIBILITY:GLASS, SIDE/REAR · VISIBILITY:POWER WINDOW DEVICES AND CONTROLS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Technical Bulletin (Squeaking Noises From Front Of Vehicle): Squeaking/creaking noise from front of vehicle while fully turning steering wheel. The document also gives information on servicing the issue
NHTSA source summary · Original PDF not reviewed by Recallfolio
Technical Bulletin (Rear Door Glass Inoperative): The rear glass cannot be opened / closed, the rear glass may slide down into the door, or the rear glass motor operates but the glass does not move. This document contains the fault codes, and procedure to service these issues
NHTSA source summary · Original PDF not reviewed by Recallfolio
Technical Bulletin (High Pressure Fuel Pump Diagnosis): Completing the GFF high pressure pump function test is essential to diagnose proper pump operation and to avoid unnecessary replacements
Source components: ELECTRICAL SYSTEM · ENGINE · FUEL SYSTEM, GASOLINE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
VOLKSWAGEN DEALERSHIP COMMUNICATION: Volkswagen announced a warranty extension program to cover the High Pressure Fuel Pump on 2009-2012 model year TDI Clean Diesel Engine vehicles
NHTSA source summary · Original PDF not reviewed by Recallfolio
VOLKSWAGEN DEALERSHIP COMMUNICATION: This document announced a warranty Volkswagen extension program to cover the High Pressure Fuel Pump on 2009-2012 model year TDI Clean Diesel Engine vehicles.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Tech Tips (Test Plan to Calibrate Adaptive Cruise Control Sensors Will Not Begin notice): Notification that If the test plan to calibrate the Adaptive Cruise Control Sensors will not begin, turn off the overhead lights in the shop. The wavelengths of some shop lighting interfere with the sensors during calibration.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Technical Bulletin (High Pressure Fuel Pump Diagnosis): Completing the GFF high pressure pump function test is essential to diagnose proper pump operation and to avoid unnecessary replacements.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Technical Bulletin (Rear Door Glass Inoperative issue diagnosis): The rear glass cannot be opened / closed, the rear glass may slide down into the door, or the rear glass motor operates but the glass does not move
NHTSA source summary · Original PDF not reviewed by Recallfolio
Technical Bulletin: This document concerns the sensitivity of the washer solvent level sensor (G33) can be affected by the type, concentration, and the presence of additives in the washer solvent currently in the tank. The operation of the level sensor relies on the composition of the solvent to provide an accurate message on the solvent level. Incorrect concentration and the presence of additives can contaminate the sensor and reduce its sensitivity.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This document infroms the customer of the decision to extend the Emissions Control Systems Warranty for the Intake Manifold & Fuel Injectors Certain 2011-2012 Model Year Volkswagen Vehicles with 2.0 TFSI Engine (Engine Codes CBFA & CCTA)
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Technical Bulletin (P2014 or P2015 Intake Manifold Faults Stored in ECM Fault Memory ): Document discusses diagnosis Codes necessary to diagnosis, and potential remedy of issue. The diagnosis codes for checking warranty coverage for servicing the vehicle are also available
NHTSA source summary · Original PDF not reviewed by Recallfolio
Tech Tips (Rear View Camera Inoperative issues): The rear view camera operates in conjunction with the rear parking aid system. If there are no faults in the radio or rear view camera, be sure to check the parking aid system for faults. Buzzer or sensor faults must be corrected for proper rear view camera operation.
Source components: BACK OVER PREVENTION: CAMERA SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
VOLKSWAGEN: BEFORE REAR VIEW CAMERA IS PROPERLY OPERATIONAL, SHOULD BE CONNECTED TO BUZZER OR SENSOR FAULTS AND WORKING IN CONJUNCTION WITH REAR PARKING AID SYSTEM. MODELS 2009-15 TIGUAN, CC, PASSAT, TOUAREG. *PE
Source components: BACK OVER PREVENTION: CAMERA SYSTEM · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When performing SVM updates, the scan tool should be hardwired to the vehicle and the Bluetooth physically turned off. A hard wired internet connection is also recommended.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT:ELECTRICAL:INFOTAINMENT:BLUETOOTH/WIFI.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Tech Tips (SVM Update Instructions): This document informs when performing SVM updates, the scan tool should be hardwired to the vehicle and the Bluetooth physically turned off. A hard wired internet connection is also recommended.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Technical Bulletin (Fuel Additive to Help Prevent Sporadic Misfire Faults): Fuel quality impacts the operating performance, efficiency and service life of the engine. The use of poor quality fuels may result in deposit build up on the fuel injectors and intake valves. This may result in a rough running condition, sporadic misfires, or cold start misfire faults storing in the ECM fault memory. This document informs a Volkswagen approved fuel additive is available to help remove and prevent deposits on fuel injectors and intake valves.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Tech Tips (Electro ? Steering - DTC 01309 008 ?No Communication with -J500-? is Stored in the ABS/ESP Module Only): This document informs If, after replacement of the steering rack, fault code 01309 008 is set in the ABS/ESP module only, follow the test plan in GFF for Driver Steering Recommendation (DSR) or channel 3 activation. If the test plan fails to clear the fault, follow the directions in this document using Vehicle Self Diagnosis in Address Word 44 - Steering Assistance:
NHTSA source summary · Original PDF not reviewed by Recallfolio
Technical Bulletin (Electric Coolant Fans Continue to Run after Ignition is Switched OFF): This documentation informs it is considered normal operation for the electric coolant fans to continue to run for up to 15 minutes after the ignition is switched off in gasoline engine applications, and up to 16 minutes in diesel engine applications. The production solution to service this issue is that no production change is required.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Tech Tips (2.0L CCTA/CBFA Coolant Leak or Repeat Coolant Leak from the Water Pump Area): Inspect the water pump for signs of contact with engine oil. Engine oil may cause the water pump gasket to swell, which may lead to a coolant leak. This document informs of the precaustions necessary if a water pump replacement is necessary.
Source components: ENGINE AND ENGINE COOLING:COOLING SYSTEM · ENGINE AND ENGINE COOLING:COOLING SYSTEM:RADIATOR ASSEMBLY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Technical Bulletin (Removing Paint Contaminants from Exterior Paint): This document informs how to remove paint contaminants such as rail dust and industrial fallout from exterior paint.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Tech Tips (ECM Fault P1250 "Fuel Level Too Low" Will Not Clear): This document informs to clear static ECM fault P1250 "Fuel Level Too Low", add fuel to vehicle and complete a road test of at least 10 miles. Simply adding fuel without completing a road test may not allow fault to clear.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Install a vacuum gauge on the dipstick tube and check crankcase vacuum at idle. Compare to a known good vehicle. If the vacuum reading is lower than the comparison vehicle, visually inspect for oil leaks between the engine and the transmission. Smoke test the crankcase by connecting the EVAP smoke machine to the dipstick tube and inspect for leaks at the rear main seal (this will limit pressure to 2 PSI). DO NOT apply shop air to the dipstick tube or the crankcase. If a rear main seal leak is identified, replace the seal. Once replaced, recheck crankcase vacuum at idle. If low, check for additional oil leaks and verify crankcase breather operation (repairing as necessary). Erase the faults and road test 10 miles to recheck operation.
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Tech Tips (RNS 510? Replacement Radio/Navigation Unit has no Sound): Replacement RNS 510 radio/navigation units may be shipped in transportation safeguard mode and therefore will have no sound output. This document informs how to deactivate the safeguard mode.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some Golf, GTI, Jetta, and Passat vehicles equipped with electromechanical power steering have the G85 steering angle sensor located in the steering rack. These vehicles do not have a G85 in the steering column. To determine G85 location, check the J500 Power steering control module part number in the GFF printout. Do not use the part number on the steering rack for this check.
Source components: BACK OVER PREVENTION · ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:ADAS:PARKING ASSIST:SENSORS · POWER TRAIN · STEERING · STEERING:RACK AND PINION:RACK · STEERING:STEERING CONTROL MODULE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Tech Tips (2009-2015 Jetta, Eos, Rabbit, Golf, GTI, Passat, CC, and Tiguan Equipped with Electromechanical Power Steering ? G85 Location Identification Tip): Ths document informs of the location of the G85 steering sensor. The sensors expected settings, and which vehicles do not have this sensor for electromechanical power steering.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Technical Bulletin (Air Conditioning, Cleaning of the Refrigerant Circuit): In cases where an air conditioning system component (such as a compressor or other system component) has failed and debris from the compressor or component is circulated throughout the refrigerant circuit, the refrigerant circuit must be cleaned of any and all debris or damage to the replacement components will result. Debris can be dispersed throughout the refrigerant circuit after a/c component damage. In order to maintain A/C operating efficiency, it is important to flush the refrigerant circuit after A/C component repairs.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Technical Bulletin (Intake Manifold Faults Stored in ECM Fault Memory issues): This document informs of a failure of Intake manifold causing fault codes to be stored in the ECM. The production solution improved intake manifold design. This document discusses the "Fault Codes" necessary to diagnosis, and potential remedy of the issue. The fault codes for checking warranty coverage for servicing the vehicle are also available.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
VOLKSWAGEN: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. AN EXTENSION WARRANTY, WITH SPECIFIC CONDITIONS, 10 YRS OR 120,000 MILES,WHICHEVER IS FIRST, HAS BEEN ISSUED FOR EMISSIONS CONTROL SYSTEMS WARRANTY FOR INTAKE MANIFOLD AND FUEL INJECTORS. MODEL 2008-2011. *PE
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When replacing the Air Conditioning compressor it is necessary to flush the entire system to remove all the PAG oil. Replacement AC compressors come with a full charge of oil. Any time another compressor is installed with a different vendor (Sanden to Denso) it is necessary to replace all the oil in the system to the new vendor type PAG oil.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Tech Tips (Comfort Module (J393) or BCM (J519) Replacement): This document informs if a comfort or body control module is replaced during normal diagnosis, make sure the factory mode has been switched OFF. This can be accomplished by selecting guided function of either the J393 or J519 or control module OBD of J393 or J519 then selecting adaptation channel 99. Failure to deactivate factory mode will create a concern where the door locks will not lock and/or unlock with the switch and/or the remotes.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Tech Tips (AC Compressor Replacement, Refrigerant Circuit Flushing Requirement): This document informs when replacing the Air Conditioning compressor it is necessary to flush the entire system to remove all the PAG oil. Replacement AC compressors come with a full charge of oil. Any time another compressor is installed with a different vendor (such as Sanden to Denso) it is necessary to replace all the oil in the system to the new vendor type PAG oil. This document also informs When installing the new AC compressor immediately transfer the AC compressor caps to the original compressor. There is also a photo to show the necessary part placement.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Technical Bulletin (Intake Manifold Fault issues): This document informs of Intake Manifold issues that are recognized in the ECM fault memory. The Production Solution to this issue was an improved intake manifold design. This document discusses the "Fault Codes" necessary to diagnosis, and potential remedy of the issue. The fault codes for checking warranty coverage for servicing the vehicle are also available.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The DLC is intended for use with diagnostic scan tools and by emissions testing stations. However, aftermarket devices (i.e., drive data recorders) that connect to the DLC have now become available.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Technical Bulletin (Intake Manifold issues): This document informs of a failure of Intake manifold causing fault codes to be stored in the ECM. The fault codes are written in the document. The product solution for this issue an Improved intake manifold design. This document discusses the "Fault Codes" necessary to diagnosis, and potential remedy of the issue. The fault codes for checking warranty coverage for servicing the vehicle are also available.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Technical Bulletin (Engine Oils Which Meet Volkswagen Oil Quality Standard): This document informs of a sample list of products generally available in the North American market that meet the Volkswagen Oil Quality Standard
NHTSA source summary · Original PDF not reviewed by Recallfolio
When diagnosis on the above engine leads to the testing of the N75, please refer to the picture below. The diagram shows which vacuum ports on the N75 valve should hold vacuum and which ones should not.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Tech Tips 92006-2014 Vehicles with 2.0T Gasoline Engine - N75 Solenoid Valve Diagnosis): When diagnosis on the above engine leads to the testing of the N75, please refer this document with graphical aid. The diagram shows which vacuum ports on the N75 valve should hold vacuum and which ones should not. Turbocharger fault codes P0299 and P0234 can be diagnosed using this test.
Source components: ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Quick Reference Update Guide: This document informs of the corresponding software/hardware and disc availability to the customer concerns about a vehicle
NHTSA source summary · Original PDF not reviewed by Recallfolio
Tech Tips (Electro - Steering issues): If, after replacement of the steering rack, fault code 01309 008 is set in the ABS/ESP module only, follow the test plan in GFF for Driver Steering Recommendation (DSR) or channel 3 activation. If the test plan fails to clear the fault, follow the directions in this document
NHTSA source summary · Original PDF not reviewed by Recallfolio
Tech Tips (Comfort Module (J393) or BCM (J519) Replacement): This document informs If a comfort or body control module is replaced during normal diagnosis, make sure the factory mode has been switched OFF. This can be accomplished by selecting the test plan through GFF or through Vehicle Self Diagnosis in adaptation channel 99. Failure to deactivate factory mode will create a concern where the door locks will not lock and/or unlock with the switch and/or the remotes.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Technical Bulletin (Oil Consumption Measurement): Customer states oil consumption is higher than the Volkswagen oil consumption standard of up to 0.5 quarts per 600 miles, or 0.5 liters per 1000 km. In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically, engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owners Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, the ambient temperature and road conditions. Further factors include the amount of oil dilution from water condensation or fuel residue and the oxidation level of the oil. This document discusses the "Fault Codes" necessary to diagnosis, and potential remedy of the issue. The fault codes for checking warranty coverage for servicing the vehicle are also available.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Tech Tips (Instrument Cluster Illumination): The instrument cluster illumination is controlled by a photocell inside the cluster. If an illumination concern is suspected, this document informs of the procedure necessary to service this issue
NHTSA source summary · Original PDF not reviewed by Recallfolio
Technical Bulletin (Slave Cylinder - Clutch Pedal Operation Diagnosis): Customer may comment: ? Complaints on clutch system. ? After pressing the clutch pedal, it remains on the floor. Due to mis-diagnosis of clutch systems, and to prevent incorrect parts replacement, diagnostic procedure implemented into guided fault finding (GFF). This document is for identifying the issue for diagnosis.