2025 Toyota TACOMA Manufacturer communications & TSBs.Page 1
Original record summaries, dates and identifiers for this model-year. Records 1–39 of 39, ordered newest first. Dated records on this page: Feb 6, 2024–Apr 10, 2026.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Apr 10, 2026Service Bulletin/Repair Instructions
T-TT-0755-24
NHTSA communication ID: 11032469
NHTSA source summary · Original PDF not reviewed by Recallfolio
The condition is for vehicles equipped with an accessory Power Port or Tire Inflator. During the installation process of the Power Port or Tire Inflator, the pre-wire connector is removed from the dummy cap (which is attached to the harness) and is left attached when power is connected. The purpose of the dummy cap is to prevent connector water intrusion/corrosion when the accessory is not installed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2005 – 2026 Toyota vehicles that have undergone water intrusion may exhibit a condition in which a musty odor is present. Follow the procedures in this bulletin to remediate the odor and address this condition. The purpose of this Service Bulletin is to provide general guidelines and procedures for odor remediation. This Service Bulletin provides a guide on how to prepare and treat the interior of the vehicle for odor remediation. Refer to the applicable model and model year Repair Manual and the EPA (Environmental Protection Agency) website for the most up-to-date safety and precautionary guidelines.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2024 – 2025 model year 4WD Tacoma and Tacoma Hybrid vehicles may exhibit a condition where the 4WD lights are flashing and a MIL ON condition with one or more of the following Diagnostic Trouble Codes (DTCs) present: •P277111 – Four Wheel Drive (4WD) Low Switch Circuit Short to Ground •P178462 – 4WD/AWD Transfer Case Shift Motor Limit Switch and Transfer Case H4-L4 Position Switch Signal Compare Failure •P17AC62 – 4WD/AWD Transfer Case Shift Motor Limit Switch Signal Compare Failure The transfer case breather hose has been updated.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The air conditioning dye injection tool kit has been developed to aid in identifying the location of air conditioning refrigerant leaks. The procedures outlined in this Service Bulletin aid in locating, inspecting, and repairing refrigerant leaks.
NHTSA source summary · Original PDF not reviewed by Recallfolio
To assist with the early detection and early resolution of audio related concerns you may be asked to recover MMR data from the head unit. The following steps are instructions on how to retrieve the data from the system and are only to be used when requested by FTS and/or FPE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
To assist with the early detection and early resolution of audio related concerns you may be asked to recover MMR data from the head unit. The following steps are instructions on how to retrieve the data from the system and are only to be used when requested by FTS and/or FPE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash reprogramming allows the Electronic Control Unit (ECU) software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Global Techstream+ (GTS+) ECU flash reprogramming procedures and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard+ (CUW+). To ensure the correct ECU software is installed, ECUs will require a Security Signature before the ECU will initialize the flash reprogramming sequence. This bulletin also details the process for acquiring a Security Signature from TIS during the GTS+ ECU flash reprogramming process.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The Immobilizer and Smart Key Reset is a feature that allows the registration of new keys when all master keys are lost. Once the system is reset, all previously registered keys will be erased and can never be reused. Another feature, Add/Remove Key, is also available. Once a key is removed, it can never be reused.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash reprogramming allows the Electronic Control Unit (ECU) software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Global Techstream+ (GTS+) ECU flash reprogramming procedures and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard+ (CUW+). To ensure the correct ECU software is installed, ECUs will require a Security Signature before the ECU will initialize the flash reprogramming sequence. This bulletin also details the process for acquiring a Security Signature from TIS during the GTS+ ECU flash reprogramming process.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The Immobilizer and Smart Key Reset is a feature that allows the registration of new keys when all master keys are lost. Once the system is reset, all previously registered keys will be erased and can never be reused. Another feature, Add/Remove Key, is also available. Once a key is removed, it can never be reused.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2024 – 2025 model year Tacoma and Tacoma Hybrid vehicles equipped with an accessory roof rack may exhibit an abnormal vibration from the accessory roof rack while driving. New roof rack bumpers have been developed to address this vibration.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021 – 2025 model year Toyota vehicles may require the download and installation of vehicle specific software or configuration software when the Electronic Control Unit (ECU) is replaced. GTS+ software has been modified to indicate when configuration software is required. A new Configure column has been added to the GTS+ Health Check Results screen to show when configuration software is available for a specific ECU.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Long-term or off-site storage requires special care to maintain vehicle condition. The following guidelines should be performed to minimize vehicle component/part degradation due to extended vehicle storage conditions. Long-term storage can affect a vehicle’s systems and components. Any problems that are found should be corrected immediately.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When certain vehicle ECUs are replaced, the ECU Security Key must be written in order for that ECU to communicate on the vehicle network. The GTS+ Software Health Check Results screen has been enhanced to help identify if a replacement ECU requires an ECU Security Key.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TSB: During the manufacturing process, tires are mounted on the vehicle as matched sets to help reduce conditions such as pulling or drifting. If the wheels are replaced or refinished before vehicle delivery, it is important that the tires remain on the vehicle in the same location and in the same direction of rotation. Refer to the Tire Positioning Procedure in this bulletin to ensure that the original tires stay in the same location on the vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
During the manufacturing process, tires are mounted on the vehicle as matched sets to help reduce conditions such as pulling or drifting. If the wheels are replaced or refinished before vehicle delivery, it is important that the tires remain on the vehicle in the same location and in the same direction of rotation.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2025 model year Toyota vehicles are equipped with driver side floor mat retainers to secure the floor mat in the correct position. In addition, some models may also utilize retainers for passenger side and rear seat floor mats. During Pre-Delivery Service (PDS), follow the appropriate Installation Procedure to attach the driver side, and if applicable, the passenger side and rear seat floor mats to the vehicle carpet using the floor mat retainers. If installation instructions are included in the floor mat kit, place the instructions in the vehicle’s glove box for customer reference.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix with rainwater, nighttime dew, or high humidity to form acidic compounds. If these contaminants settle and remain on a painted vehicle surface, especially the horizonal areas of the hood, roof, and decklid, significant damage can occur. This damage is the result of actual etching of the paint and appears as pitting or water spots. As acid rain droplets on the vehicle surface evaporate, the concentration strength of the acid increases, causing deeper and more rapid damage. This evaporation and corrosive action also occur more rapidly on dark colored cars as direct sun heat increases. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. In areas known for high frequency and/or concentration of acid rain, frequent vehicle washing during high heat or humidity periods will minimize the potential for paint damage caused by acid rain. It is further recommended that either reverse osmosis or deionized water be used to prevent water spotting.
NHTSA source summary · Original PDF not reviewed by Recallfolio
To prevent brake rotor rust from forming during transportation and storage, wheel film will be used instead of a cardboard type of anti-rust cover. The purpose of the wheel film is to shield the disc brake rotor from weather elements and initial rust before the vehicle is delivered to the customer. Consequently, the film should remain on the wheel for as long as possible.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical impurities in the atmosphere. If these acidic compounds settle on an exposed vehicle, especially the horizontal areas such as the hood, roof, and decklid, significant damage to the painted surfaces can occur. Acid rain damage can typically be identified on vehicles by the presence of stains on the paint surface that resemble hard water spots. Unlike water spots however, acid rain damage cannot be removed by regular washing procedures. Also, because acid rain can etch and soften the paint, normal buffing or polishing repair procedures should not be attempted. This can cause further damage and result in visible depressions in the paint surface. The following are the three major categories of acid rain damage: •Minor damage: requires only buffing to repair. •Moderate damage: usually requires neutralizing, color sanding, and buffing. •Severe damage: extending beyond 1/2 mil of clearcoat on a pearl, metallic, or solid color, requires neutralization, sanding, and repainting. In cases where acid rain damage is minor, neutralization and buffing with a liquid-type paint finessing product may provide an adequate repair. Only specially formulated products outlined in this bulletin should be used for that purpose. Unfortunately, other than minor damage, there is no simple method of determining the actual extent (depth) of acid penetration other than color sanding a representative affected area until there is no visible etching or depressions, followed by measuring the amount of paint removed with either a magnetic or digital-type film thickness gauge. The procedures in this bulletin are intended for use by qualified body/paint technicians and should not be attempted by inexperienced personnel. It is the dealer’s responsibility to protect and maintain the quality of the vehicle’s paint finish after receipt at the dealership prior to the first sale. Perform frequent vehicle washing, as often as daily, during high heat and humidity periods to minimize the potential for paint damage due to acid rain exposure. This is especially important in geographical areas known for high frequency and concentration of acid rain and industrial fallout.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Pre-Delivery Service (PDS) is a critical step in satisfying our new car customers. Customer feedback indicates the following areas deserve special attention when performing PDS: •Careful inspection for paint chips/scratches and body dents/dings. •Proper operation of electrical accessories (including interior light, clock, and radio reset). •Interior cleanliness. •Proper function of mechanical systems. Customer retention and proper maintenance of vehicles are, and have always been, a major focus for Toyota. To help remind customers that regular service is essential to the proper maintenance of the vehicle, dealers are required to install a service reminder sticker before delivery. By doing this, customers will be reminded to return to your dealership for service. Your current service reminder sticker may be used. (See PDS Check Sheet item 8 of “Final Inspection and Cleaning.”) This bulletin contains the PDS procedures that apply specifically to 2025 model year Tacoma and Tacoma Hybrid vehicles. Refer to T-SB-0028-24, the universal Check Sheet that contains PDS steps that apply to al 2025 model year Toyota vehicles. To properly perform a complete PDS, you must complete all procedures contained in this TSB as well as the universal PDS Check Sheet. In addition, if the vehicle is stored for over 30 days, refer to T-SB-0023-24, Long-Term Vehicle Storage Guidelines.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Toyota vehicles are currently protected with RapgardTM protective film designed to protect the horizontal painted surfaces. This material protects from acid rain, environmental fallout, and rail contamination. Follow the Removal Procedure in this bulletin to remove the RapgardTM protective film within 90 days from initial application.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Vehicles may occasionally be subjected to contamination by airborne iron particles shed from railroad tracks, train wheels, exposure to heavy machinery facilities, grinding, welding, etc. This type of contamination can be identified by the presence of small, red or brown particles on the paint surface. These particles are often difficult to see on dark color paints but can be easily felt when brushing a hand across horizontal body surfaces such as the hood, roof, or deck lid. Follow the Repair Procedure in this bulletin to clean vehicles that may have been subjected to contamination by airborne iron particles such as rail dust during rail transportation or extended storage near industrial areas.
NHTSA source summary · Original PDF not reviewed by Recallfolio
A battery in a stored vehicle is subject to conditions that can reduce its performance and service life. These conditions include storage period, temperature, parasitic drain, and battery load. Because of these factors, battery inspection and maintenance are required in order to ensure proper operation and optimal battery life. Electrified vehicles are equipped with two types of batteries, a High Voltage (HV) battery and a 12V battery. Conventional vehicles are equipped with only a 12V battery. As a matter of policy, Toyota does not provide battery warranty coverage for discharged and/or failed batteries due to lack of maintenance. It is the dealer’s responsibility to maintain the specified State-Of-Charge (SOC) of the vehicle’s battery while in stock and ensure proper SOC at delivery. To reduce customer service concerns due to an undercharged battery, ALL dealers should test the 12V battery and recharge, if necessary, no more than 48 hours before delivery to the customer.
NHTSA source summary · Original PDF not reviewed by Recallfolio
A battery in a stored vehicle is subject to conditions that can reduce its performance and service life. These conditions include storage period, temperature, parasitic drain, and battery load. Because of these factors, battery inspection and maintenance are required in order to ensure proper operation and optimal battery life.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2025 model year Toyota vehicles are equipped with driver side floor mat retainers to secure the floor mat in the correct position. In addition, some models may also utilize retainers for passenger side and rear seat floor mats. During Pre-Delivery Service (PDS), follow the appropriate Installation Procedure to attach the driver side, and if applicable, the passenger side and rear seat floor mats to the vehicle carpet using the floor mat retainers. If installation instructions are included in the floor mat kit, place the instructions in the vehicle’s glove box for customer reference.
NHTSA source summary · Original PDF not reviewed by Recallfolio
During the manufacturing process, tires are mounted on the vehicle as matched sets to help reduce conditions such as pulling or drifting. If the wheels are replaced or refinished before vehicle delivery, it is important that the tires remain on the vehicle in the same location and in the same direction of rotation.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Long-term or off-site storage requires special care to maintain vehicle condition. The following guidelines should be performed to minimize vehicle component / part degradation due to extended vehicle storage conditions. Long-term storage can affect a vehicle’s systems and components. Any problems that are found should be corrected immediately.
NHTSA source summary · Original PDF not reviewed by Recallfolio
A battery in a stored vehicle is subject to conditions that can reduce its performance and service life. These conditions include storage period, temperature, parasitic drain, and battery load. Because of these factors, battery inspection and maintenance are required in order to ensure proper operation and optimal battery life.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2025 model year Toyota vehicles are equipped with driver side floor mat retainers to secure the floor mat in the correct position. In addition, some models may also utilize retainers for passenger side and rear seat floor mats. During Pre-Delivery Service (PDS), follow the appropriate Installation Procedure to attach the driver side, and if applicable, the passenger side and rear seat floor mats to the vehicle carpet using the floor mat retainers. If installation instructions are included in the floor mat kit, place the instructions in the vehicle’s glove box for customer reference.
NHTSA source summary · Original PDF not reviewed by Recallfolio
During the manufacturing process, tires are mounted on the vehicle as matched sets to help reduce conditions such as pulling or drifting. If the wheels are replaced or refinished before vehicle delivery, it is important that the tires remain on the vehicle in the same location and in the same direction of rotation.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Long-term or off-site storage requires special care to maintain vehicle condition. The following guidelines should be performed to minimize vehicle component / part degradation due to extended vehicle storage conditions. Long-term storage can affect a vehicle’s systems and components. Any problems that are found should be corrected immediately.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Long-term or off-site storage requires special care to maintain vehicle condition. The following guidelines should be performed to minimize vehicle component / part degradation due to extended vehicle storage conditions. Long-term storage can affect a vehicle’s systems and components. Any problems that are found should be corrected immediately.
NHTSA source summary · Original PDF not reviewed by Recallfolio
A battery in a stored vehicle is subject to conditions that can reduce its performance and service life. These conditions include storage period, temperature, parasitic drain, and battery load. Because of these factors, battery inspection and maintenance are required in order to ensure proper operation and optimal battery life.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Long-term or off-site storage requires special care to maintain vehicle condition. The following guidelines should be performed to minimize vehicle component / part degradation due to extended vehicle storage conditions. Long-term storage can affect a vehicle’s systems and components. Any problems that are found should be corrected immediately.
NHTSA source summary · Original PDF not reviewed by Recallfolio
A battery in a stored vehicle is subject to conditions that can reduce its performance and service life. These conditions include storage period, temperature, parasitic drain, and battery load. Because of these factors, battery inspection and maintenance are required in order to ensure proper operation and optimal battery life.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This is to advise of various price adjustments that will affect Toyota Genuine Motor Oil and Long Life Coolant, effective March 1, 2024. These products are ordered through the Toyota Complete Maintenance Care (TCMC) website.
Source components: ENGINE AND ENGINE COOLING · ENGINE AND ENGINE COOLING:ENGINE:OIL/LUBRICATION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TSB: 2025 model year Toyota vehicles are equipped with driver side floor mat retainers to secure the floor mat in the correct position. In addition, some models may also utilize retainers for passenger side and rear seat floor mats. During Pre-Delivery Service (PDS), follow the appropriate Installation Procedure to attach the driver side, and if applicable, the passenger side and rear seat floor mats to the vehicle carpet using the floor mat retainers. If installation instructions are included in the floor mat kit, place the instructions in the vehicle?s glove box for customer reference.