The manufacturer’s record · Page 3 of 3

2002 Saturn SL
Manufacturer communications & TSBs.Page 3

Original record summaries, dates and identifiers for this model-year. Records 201–244 of 244, ordered newest first. Dated records on this page: May 1, 2009–Feb 26, 2014.

Back to 2002 Saturn SL problems & recalls
Read the applicability before drawing a conclusion.

This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.

NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.

Feb 26, 2014Service Bulletin/Repair Instructions

PIC3011H

NHTSA communication ID: 10111964

NHTSA source summary · Original PDF not reviewed by Recallfolio

This Preliminary Information communication provides information to the technician about vehicles that have the OnStar system does not respond properly to some numbers and/or voice commands. Dealer should direct the customer to review the operational characteristics in the OnStar Users Guide.

Source components: ELECTRICAL SYSTEM:SOFTWARE.

Source record 10111964 at NHTSA
Feb 12, 2014Service Bulletin/Repair Instructions

PIT4943C

NHTSA communication ID: 10111927

NHTSA source summary · Original PDF not reviewed by Recallfolio

This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.

Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · FUEL SYSTEM, GASOLINE · SERVICE BRAKES, HYDRAULIC.

Source record 10111927 at NHTSA
Feb 4, 2014Service Bulletin/Repair Instructions

PIC5453A

NHTSA communication ID: 10111894

NHTSA source summary · Original PDF not reviewed by Recallfolio

This Preliminary Information communication provides information to the technician that General Motors and General Motors of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.

Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.

Source record 10111894 at NHTSA
Feb 1, 2014Service Bulletin/Repair Instructions

99-08-51-007F

NHTSA communication ID: 10190932

NHTSA source summary · Original PDF not reviewed by Recallfolio

Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility — Outside Company later in this bulletin.

Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · WHEELS.

Source record 10190932 at NHTSA
Feb 1, 2014Service Bulletin/Repair Instructions

99-08-51-007F

NHTSA communication ID: 10190931

NHTSA source summary · Original PDF not reviewed by Recallfolio

Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility — Outside Company later in this bulletin.

Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · WHEELS.

Source record 10190931 at NHTSA
Jan 22, 2014Service Bulletin/Repair Instructions

PIC5953

NHTSA communication ID: 10112013

NHTSA source summary · Original PDF not reviewed by Recallfolio

This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.

Source components: EQUIPMENT:ELECTRICAL.

Source record 10112013 at NHTSA
Jan 16, 2014Service Bulletin/Repair Instructions

PIP3140F

NHTSA communication ID: 10111997

NHTSA source summary · Original PDF not reviewed by Recallfolio

This Preliminary Information communication advises the technician that a noise or a vibration in the vehicle that seems to be abnormal may not have been there when the vehicle was purchased. Technician should look for Non - General Motors aftermarket accessories installed on the vehicle that can cause these issues.

Source components: EQUIPMENT.

Source record 10111997 at NHTSA
Jan 1, 2014Service Bulletin/Repair Instructions

PI0281D

NHTSA communication ID: 10190934

NHTSA source summary · Original PDF not reviewed by Recallfolio

Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.

Source components: EQUIPMENT ADAPTIVE/MOBILITY · STRUCTURE:FRAME AND MEMBERS:UNDERBODY SHIELDS.

Source record 10190934 at NHTSA
Jan 1, 2014Service Bulletin/Repair Instructions

PI0281D

NHTSA communication ID: 10190933

NHTSA source summary · Original PDF not reviewed by Recallfolio

Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.

Source components: EQUIPMENT ADAPTIVE/MOBILITY · STRUCTURE:FRAME AND MEMBERS:UNDERBODY SHIELDS.

Source record 10190933 at NHTSA
Dec 16, 2013Service Bulletin/Repair Instructions

10-00-89-006C

NHTSA communication ID: 10133103

NHTSA source summary · Original PDF not reviewed by Recallfolio

This informational bulletin provides directions on submitting different PIRs

Source components: BACK OVER PREVENTION: SENSING SYSTEM: RADAR.

Source record 10133103 at NHTSA
Dec 4, 2013Service Bulletin/Repair Instructions

05-00-89-072C

NHTSA communication ID: 10133086

NHTSA source summary · Original PDF not reviewed by Recallfolio

This informational bulletin provides information on how to save fuel and proper maintenance without using fuel or oil additives.

Source components: FUEL SYSTEM, DIESEL · FUEL SYSTEM, GASOLINE · FUEL SYSTEM, OTHER.

Source record 10133086 at NHTSA
Nov 1, 2013Service Bulletin/Repair Instructions

PIP5163

NHTSA communication ID: 10112331

NHTSA source summary · Original PDF not reviewed by Recallfolio

This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.

Source components: ENGINE AND ENGINE COOLING.

Source record 10112331 at NHTSA
Sep 3, 2013Service Bulletin/Repair Instructions

PIT3099K

NHTSA communication ID: 10113227

NHTSA source summary · Original PDF not reviewed by Recallfolio

This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partech for assistance.

Source components: EQUIPMENT.

Source record 10113227 at NHTSA
Sep 1, 2013Service Bulletin/Repair Instructions

130089009

NHTSA communication ID: 10246631

NHTSA source summary · Original PDF not reviewed by Recallfolio

Expanded Availability for Remanufacture and Return (R&R) Electronic Control Modules

Source components: ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM).

Source record 10246631 at NHTSA
Aug 20, 2013Service Bulletin/Repair Instructions

PIC5904

NHTSA communication ID: 10113199

NHTSA source summary · Original PDF not reviewed by Recallfolio

This Preliminary Information communication provides information to the technician about vehicles that the OnStar system will not connect. Technician should record module info per the latest version of PIC4310 and contact General Motors Technical Assistance Center.

Source components: ELECTRICAL SYSTEM.

Source record 10113199 at NHTSA
Jul 12, 2013Service Bulletin/Repair Instructions

10-00-89-010C

NHTSA communication ID: 10130567

NHTSA source summary · Original PDF not reviewed by Recallfolio

This informational bulletin provides information on key codes security rules and information on GM key code look up application.

Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.

Source record 10130567 at NHTSA
Jul 9, 2013Service Bulletin/Repair Instructions

10-00-89-009B

NHTSA communication ID: 10130562

NHTSA source summary · Original PDF not reviewed by Recallfolio

This informational bulletin provides information on key code security and information on GM key code look up applications.

Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.

Source record 10130562 at NHTSA
May 23, 2013Service Bulletin/Repair Instructions

11-00-89-005E

NHTSA communication ID: 10139067

NHTSA source summary · Original PDF not reviewed by Recallfolio

This informational bulletin provides a revision for 11-00-89-005D to add additional Mandatory Minimum Tables and additional information concerning Policy decision making.

Source components: EQUIPMENT.

Source record 10139067 at NHTSA
May 23, 2013Service Bulletin/Repair Instructions

08-06-01-006D

NHTSA communication ID: 10139066

NHTSA source summary · Original PDF not reviewed by Recallfolio

This informational bulletin provides information for Engine Squealing Type Noise on Start-up or Vibration Condition.

Source components: ENGINE AND ENGINE COOLING · EQUIPMENT.

Source record 10139066 at NHTSA
May 16, 2013Service Bulletin/Repair Instructions

05-08-48-001C

NHTSA communication ID: 10139049

NHTSA source summary · Original PDF not reviewed by Recallfolio

This informational bulletin provides a revision for 05-08-48-001B to add 2010-2014 model years and update Labor Operation.

Source components: EQUIPMENT · VISIBILITY:WINDSHIELD.

Source record 10139049 at NHTSA
May 2, 2013Service Bulletin/Repair Instructions

PIT4720C

NHTSA communication ID: 10113074

NHTSA source summary · Original PDF not reviewed by Recallfolio

This Preliminary Information communication provides information to the technician that after replacing the Instrument Panel Cluster the exchange center is unable to program the actual mileage on the odometer or the actual mileage is unknown. Dealer will need to follow dealer to the General Motors service policies and procedures manual section 3.2.4 odometer servicing.

Source components: ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL · EQUIPMENT.

Source record 10113074 at NHTSA
Apr 25, 2013Service Bulletin/Repair Instructions

13-00-89-005

NHTSA communication ID: 10130652

NHTSA source summary · Original PDF not reviewed by Recallfolio

This technical bulletin provides Warranty Administration - New Labor Codes information.

Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.

Source record 10130652 at NHTSA
Apr 11, 2013Service Bulletin/Repair Instructions

99-04-20-002H

NHTSA communication ID: 10130627

NHTSA source summary · Original PDF not reviewed by Recallfolio

This technical bulletin provides a revision of 99-04-20-002G to add 2013-2014 model years.

Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.

Source record 10130627 at NHTSA
Mar 26, 2013Service Bulletin/Repair Instructions

11-00-89-005D

NHTSA communication ID: 10134681

NHTSA source summary · Original PDF not reviewed by Recallfolio

This warranty administration bulletin provide policy information on clarification of use-dealer empowerment labor operations and customer enthusiasm.

Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.

Source record 10134681 at NHTSA
Mar 4, 2013Service Bulletin/Repair Instructions

00-03-10-002G

NHTSA communication ID: 10134640

NHTSA source summary · Original PDF not reviewed by Recallfolio

This informational bulletin provides information on the appearance of chromed aluminum wheels due to chemical staining, pitting corrosion and/or spotted.

Source components: WHEELS.

Source record 10134640 at NHTSA
Feb 26, 2013Service Bulletin/Repair Instructions

PIP3140E

NHTSA communication ID: 10112885

NHTSA source summary · Original PDF not reviewed by Recallfolio

This Preliminary Information communication advises the technician that a noise or a vibration in the vehicle that seems to be abnormal may not have been there when the vehicle was purchased. Technician should look for Non - General Motors aftermarket accessories installed on the vehicle that can cause these issues.

Source components: EQUIPMENT.

Source record 10112885 at NHTSA
Feb 13, 2013Service Bulletin/Repair Instructions

PIP5094

NHTSA communication ID: 10112857

NHTSA source summary · Original PDF not reviewed by Recallfolio

This Preliminary Information communication advises the technician that, when testing any circuit for open or resistance, it is imperative that all related terminal pin fit and tension be checked when the test steps require disconnection of the connector or component, prior to any component replacement. Always use the recommended terminal test tool during these tests.

Source components: ELECTRICAL SYSTEM.

Source record 10112857 at NHTSA
Dec 17, 2012Service Bulletin/Repair Instructions

11-00-89-005C

NHTSA communication ID: 10138541

NHTSA source summary · Original PDF not reviewed by Recallfolio

This warranty administration bulletin provides information on the Clarification of Use for Dealer Empowerment Labor Operations and Customer Enthusiasm

Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.

Source record 10138541 at NHTSA
Dec 17, 2012Service Bulletin/Repair Instructions

11-00-89-005C

NHTSA communication ID: 10113843

NHTSA source summary · Original PDF not reviewed by Recallfolio

This warranty administration bulletin provides information on the Clarification of Use for Dealer Empowerment Labor Operations and Customer Enthusiasm

Source components: EQUIPMENT ADAPTIVE/MOBILITY.

Source record 10113843 at NHTSA
Dec 13, 2012Service Bulletin/Repair Instructions

PIC3718E

NHTSA communication ID: 10112664

NHTSA source summary · Original PDF not reviewed by Recallfolio

This Preliminary Information communication provides information to the technician about vehicles may have a no power or no connect concern. Technician will find that the OnStar led is red and Diagnostic Trouble Code U1500 is set. Technician will need to replace the Vehicle Communication Interface Module if the Station Identification number falls in the ranges 14,000,000 - 16,000,000 or 22,000,000 - 23,200,000.

Source components: ELECTRICAL SYSTEM.

Source record 10112664 at NHTSA
Dec 12, 2012Service Bulletin/Repair Instructions

PIT3173C

NHTSA communication ID: 10112641

NHTSA source summary · Original PDF not reviewed by Recallfolio

This Preliminary Information communication provides information to the technician that fluid contamination may be directed to one of the following testing centers according to the type of fluid needing testing. Dealer should send the correct fluid to the proper testing center.

Source components: ENGINE AND ENGINE COOLING.

Source record 10112641 at NHTSA
Nov 30, 2012Service Bulletin/Repair Instructions

080846004A

NHTSA communication ID: 10126163

NHTSA source summary · Original PDF not reviewed by Recallfolio

This informational bulletin provides information regarding the aftermarket device interference with onstar diagnostic service.

Source components: ELECTRICAL SYSTEM:SOFTWARE.

Source record 10126163 at NHTSA
Nov 28, 2012Service Bulletin/Repair Instructions

000089027G

NHTSA communication ID: 10126171

NHTSA source summary · Original PDF not reviewed by Recallfolio

This informational bulletin provides a step by step procedure on how to properly use the GM chemicals to eliminate unwanted odors in vehicles and which products to use for each application.

Source components: EQUIPMENT.

Source record 10126171 at NHTSA
Nov 28, 2012Service Bulletin/Repair Instructions

PIC4310H

NHTSA communication ID: 10112607

NHTSA source summary · Original PDF not reviewed by Recallfolio

This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.

Source components: EQUIPMENT:ELECTRICAL · EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM).

Source record 10112607 at NHTSA
Nov 13, 2012Service Bulletin/Repair Instructions

100089010B

NHTSA communication ID: 10126196

NHTSA source summary · Original PDF not reviewed by Recallfolio

This informational bulletin provides information and rules for GM keycode look up applicationa dn the key code security rules and regulations for Canada only.

Source components: EQUIPMENT.

Source record 10126196 at NHTSA
Nov 12, 2012Service Bulletin/Repair Instructions

010089010J

NHTSA communication ID: 10126200

NHTSA source summary · Original PDF not reviewed by Recallfolio

This informational bulletin provides a single point reference and strategy document to aid in reducing customer comebacks, and the possibility of buyback situations by outlining specific guidelines, strategy and forms that will assist with this goal, by identifying, clarifying and documenting customer concerns accurately at each service visit.

Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.

Source record 10126200 at NHTSA
Nov 9, 2012Service Bulletin/Repair Instructions

PIT4907A

NHTSA communication ID: 10112560

NHTSA source summary · Original PDF not reviewed by Recallfolio

This Preliminary Information communication provides information to the technician about brake rotors on new vehicles and replacement parts from General Motors Service Parts Operations. Technician should be advised the costing should not be removed from the brake rotor it will wear off with normal brake usage. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.

Source components: SERVICE BRAKES.

Source record 10112560 at NHTSA
Nov 1, 2012Service Bulletin/Repair Instructions

PIC4935D

NHTSA communication ID: 10112528

NHTSA source summary · Original PDF not reviewed by Recallfolio

This Preliminary Information communication provides information to the technician about vehicles that during battery parasitic drain test, there may be some confusion as to what the normal power consumption reading should be from the OnStar system. Technician should understand the power cycles of the various OnStar systems. All Generation 6, 7, 8, and 9 systems are powered up continuously for 48 hours from ignition off. After 120 hours from ignition off, these systems then completely power off. The Onstar modules draw: * IGN ON - 240 to 400 Milliamp. * IGN OFF - 3 to 20 Milliamp for 48 hours or 120 hours on Gen 9 and vehicle communication platforms. * IGN OFF - 0.2 to 0.8 Milliamp after 48 hours or 120 hours on Gen 9 and vehicle communication platforms.

Source components: ELECTRICAL SYSTEM.

Source record 10112528 at NHTSA
Oct 18, 2012Service Bulletin/Repair Instructions

PIT3099J

NHTSA communication ID: 10112494

NHTSA source summary · Original PDF not reviewed by Recallfolio

This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts. Technician can check Service Information for some accessories. Technician can also contact Partech for assistance.

Source components: EQUIPMENT ADAPTIVE/MOBILITY.

Source record 10112494 at NHTSA
Oct 10, 2012Service Bulletin/Repair Instructions

11-00-89-005B

NHTSA communication ID: 10118626

NHTSA source summary · Original PDF not reviewed by Recallfolio

This warranty administrational bulletin provides information on Clarification of Use - Dealer Empowerment Labor Operations and Customer Enthusiasm

Source components: EQUIPMENT ADAPTIVE/MOBILITY.

Source record 10118626 at NHTSA
Oct 1, 2012Service Bulletin/Repair Instructions

PIC5588A

NHTSA communication ID: 10246951

NHTSA source summary · Original PDF not reviewed by Recallfolio

Programming And Activation Of Replacement OnStar Modules.

Source components: EQUIPMENT:ELECTRICAL.

Source record 10246951 at NHTSA
Feb 1, 2012Service Bulletin/Repair Instructions

SB-020842001B

NHTSA communication ID: 631244

NHTSA source summary · Original PDF not reviewed by Recallfolio

GENERAL MOTORS VEHICLES AND TRUCKS: SUBJECT REGARDING, 2002 AND PRIOR PASSENGER CARS AND TRUCKS, CHEMICAL DAMAGE TO EXTERIOR POLYCARBONATE HEADLAMP LENSES. *SLC UPDATED *EH UPDATED 3/30/11. HEADLAMP LENS OVERHEATING WHEN COVERED AND CHEMICAL DAMAGE TO EXTERIOR POLYCARBONATE HEADLAMP LENSES. CAN CAUSE CRAZING OR CRACKING OF HEADLAMP LENS. *PE UPDATED 6/24/11. *PE UPDATED 5/14/12. INCLUDING 2013 MODEL YEAR. *PE

Source components: EXTERIOR LIGHTING:HEADLIGHTS.

Source record 631244 at NHTSA
Nov 1, 2011Service Bulletin/Repair Instructions

SB-10-08-50-003B

NHTSA communication ID: 10042986

NHTSA source summary · Original PDF not reviewed by Recallfolio

GENERAL MOTORS: INFORMATION PROVIDED BY BULLETIN FOR ALL 2012 AND PRIOR GENERAL MOTOR TRUCKS AND PASSENGER VEHICLES REGARDING THE ADJUSTABLE COMFORT AND CUSTOM UPHOLSTERY OF THE DRIVER AND THE PASSENGER HEAD RESTRAINT. *PE

Source components: SEATS:FRONT ASSEMBLY:HEAD RESTRAINT.

Source record 10042986 at NHTSA
May 1, 2009Service Bulletin/Repair Instructions

050310003

NHTSA communication ID: 10024405

NHTSA source summary · Original PDF not reviewed by Recallfolio

LOW TIRE PRESSURE, LEAKING CAST ALUMINUM WHEELS (REPAIR WITH ADHESIVE SEALANT). 2008 AND PRIOR GM PASSENGER CAR AND LIGHT DUTY TRUCKS (INCLUDING SATURN) AND HUMMER H2, H3 AND SAAB 9-7X WITH CAST ALUMINUM WHEELS. *NJ UPDATED 10/23/09. *PE

Source components: WHEELS:RIM.

Source record 10024405 at NHTSA