Original record summaries, dates and identifiers for this model-year. Records 201–300 of 497, ordered newest first. Dated records on this page: May 2, 2020–Apr 17, 2021.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Apr 17, 2021Service Bulletin/Repair Instructions
S2008000113 Rev.
NHTSA communication ID: 10194007
NHTSA source summary · Original PDF not reviewed by Recallfolio
No Start Intermittently, Vehicle Requires Multiple Keyless Push To Start Attempts To Start Vehicle, Intermittent Key Not Detected Message
NHTSA source summary · Original PDF not reviewed by Recallfolio
Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
NHTSA source summary · Original PDF not reviewed by Recallfolio
ADAPTER, Engine Oil Filter (Pentastar V6) All vehicles equipped with a 3.2L or 3.6L except for model year 2014 vehicles with leak concern: 1) Ensure the Oil Filter Adapter (OFA) Cap O-ring is seated in the proper groove in the cap and not damaged or cut. 2) If replacing the (OFA) due to a leak detected between (OFA) and block. Ensure the torque on the 5 bolts are torqued to 12nm. If not record the actual values, torque to 12nm and contact the FCA employees listed below. 3) Remove the (OFA) and replace the O-ring and gaskets only (Kit #68191356A$), NOT THE OFA. 4) If oil was drained, add oil dye to ensure the leak is repaired. For model year 2014 vehicles replace the Oil Filter Adaptor. 5) When replacing PN's 68310865A$ & 68308741A$, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
NHTSA source summary · Original PDF not reviewed by Recallfolio
PLATE - CLUTCH PRESSURE For 68RFE trans use selective fit pressure plates between the overdrive and reverse clutch packs and hence use all three 52119929A$, 52119930A$, 04799116A$ maintain clearance For 65RFE & 66RFE no selectives for this pressure plate: 65RFE use 04799116A$ 66RFE use 52119929A$
NHTSA source summary · Original PDF not reviewed by Recallfolio
PLATE - CLUTCH PRESSURE For 68RFE trans use selective fit pressure plates between the overdrive and reverse clutch packs and hence use all three 52119929A$, 52119930A$, 04799116A$ maintain clearance For 65RFE & 66RFE no selectives for this pressure plate: 65RFE use 04799116A$ 66RFE use 52119929A$
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · SERVICE BRAKES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Dual EVAP System Extreme Duty Vapor Canister Filter Kit This informational bulletin is to make technicians aware that an EVAP dual vapor canister filter kit(Mopar part #68478013AA)is available in place of the OEM single vapor canister filter.This kit should not be installed on vehicles driven in normal conditions that are not subjected to the below symptom/conditions. Customers operating fleet or severe/extreme duty gasoline vehicles in continuous dusty driving conditions can plug the single OE filter system and may experience a Malfunction Indicator Lamp (MIL) illumination. Upon furtherinvestigation the technician may find that the following Diagnostic Trouble Codes (DTCs) have been set:P0441 - EVAP Purge System Performance. P062A - Fuel Pump Control Performance. Customers may also experience the following conditions:Hard to fill fuel tank with fuel. Premature shut-off of the gas nozzle when refueling. Flow back of fuel while refueling.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Dual EVAP System Extreme Duty Vapor Canister Filter Kit This informational bulletin is to make technicians aware that an EVAP dual vapor canister filter kit(Mopar part #68478013AA)is available in place of the OEM single vapor canister filter.This kit should not be installed on vehicles driven in normal conditions that are not subjected to the below symptom/conditions. Customers operating fleet or severe/extreme duty gasoline vehicles in continuous dusty driving conditions can plug the single OE filter system and may experience a Malfunction Indicator Lamp (MIL) illumination. Upon furtherinvestigation the technician may find that the following Diagnostic Trouble Codes (DTCs) have been set:P0441 - EVAP Purge System Performance. P062A - Fuel Pump Control Performance. Customers may also experience the following conditions:Hard to fill fuel tank with fuel. Premature shut-off of the gas nozzle when refueling. Flow back of fuel while refueling.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Tailgate Cable Has Excessive Slack or is Loose This bulletin involves replacing one of the tailgate cables with a new tailgate service cable. The customer may comment on one or more of the following:One tailgate cable has too much slack or is loose. The tailgate cables are different lengths.
Source components: EQUIPMENT · STRUCTURE:BODY:TAILGATE:HINGE AND ATTACHMENTS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Tailgate Cable Has Excessive Slack or is Loose This bulletin involves replacing one of the tailgate cables with a new tailgate service cable. The customer may comment on one or more of the following:One tailgate cable has too much slack or is loose. The tailgate cables are different lengths.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customer may complain of a MIL lamp on. Upon further investigation there could be a fault code in the PCM for P1524 ? Oil Pressure Out of Range ? Camshaft Advance/Retard Disabled.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customer may complain of a MIL lamp on. Upon further investigation there could be a fault code in the PCM for P1524 ? Oil Pressure Out of Range ? Camshaft Advance/Retard Disabled.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customer complaints may include abnormal engine noise, rough idle, lack of power, misfire. Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.
Source components: ENGINE AND ENGINE COOLING:ENGINE:CRANK/CAMSHAFT POSITION SENSOR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customer complaints may include abnormal engine noise, rough idle, lack of power, misfire. Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.
NHTSA source summary · Original PDF not reviewed by Recallfolio
(Rev. A) Malfunction Indicator Light (MIL) Illuminated. Service Diesel Exhaust Fluid (DEF) System ? See Dealer Soon Message on Electronic Vehicle Information Center (EVIC) Along With Possible Diagnostic Trouble Code (DTC) P241D - SCR Inducement - Forced Engine Shutdown.
NHTSA source summary · Original PDF not reviewed by Recallfolio
(Rev. A) Malfunction Indicator Light (MIL) Illuminated. Service Diesel Exhaust Fluid (DEF) System ? See Dealer Soon Message on Electronic Vehicle Information Center (EVIC) Along With Possible Diagnostic Trouble Code (DTC) P241D - SCR Inducement - Forced Engine Shutdown.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM · EQUIPMENT · FUEL SYSTEM, DIESEL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
(Rev. A) Malfunction Indicator Light (MIL) Illuminated. Service Diesel Exhaust Fluid (DEF) System ? See Dealer Soon Message on Electronic Vehicle Information Center (EVIC) Along With Possible Diagnostic Trouble Code (DTC) P241D - SCR Inducement - Forced Engine Shutdown.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING:ENGINE:DIESEL · FUEL SYSTEM, DIESEL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Aluminum Body Panel Corrosion Repair This bulletin involves inspecting and if necessary removing corrosion and refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Aluminum Body Panel Corrosion Repair This bulletin involves inspecting and if necessary removing corrosion and refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Drivetrain Control Module (DTCM) Update This bulletin involves reprogramming the DTCM with the latest available software. The customer may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC) has been set::If the customer has any concerns with the transfer case or if the tech performs any repairs on the transfer case, the software must be updated.C140E - Transfer Case Motor Blocked. If DTC C140E is present, follow normal diagnostic procedures before updating the DTCM.In addition the customer may describe the following:The ?Service 4WD? message/fault is displayed in the Instrument Panel Cluster (IPC). Transfer case shift fork tabs broken during range shift. Noisy (clunking/ratcheting) transfer case range shifts. Failure to complete transfer case range shifts. The following software enhancement is available:This update will help reduce premature transfer case failure.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · EXTERIOR LIGHTING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Drivetrain Control Module (DTCM) Update This bulletin involves reprogramming the DTCM with the latest available software. The customer may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC) has been set::If the customer has any concerns with the transfer case or if the tech performs any repairs on the transfer case, the software must be updated.C140E - Transfer Case Motor Blocked. If DTC C140E is present, follow normal diagnostic procedures before updating the DTCM.In addition the customer may describe the following:The ?Service 4WD? message/fault is displayed in the Instrument Panel Cluster (IPC). Transfer case shift fork tabs broken during range shift. Noisy (clunking/ratcheting) transfer case range shifts. Failure to complete transfer case range shifts. The following software enhancement is available:This update will help reduce premature transfer case failure.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · POWER TRAIN:TRANSFER CASE (4-WHEEL DRIVE).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Power Distribution Center If the PDC is being replaced due to a failed internal fuel pump relay, the relay can now be serviced as a separate component. Please use relay replacement KIT part number: 68510768A$.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Intelligent Power Distribution Center If the PDC requires replacement due to a failed internal fuel pump relay, the relay can now be serviced as a separate component. Please use relay replacement KIT part number: 68510768A$.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Power Distribution Center If the PDC is being replaced due to a failed internal fuel pump relay, the relay can now be serviced as a separate component. Please use relay replacement KIT part number: 68510768A$.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find oneor more of the following Diagnostic Trouble Codes (DTCs):P0133-00 - O2 Sensor 1/1 Slow Response. P20EE-00 - SCR NOX Catalyst Efficiency Below Threshold Bank 1. P050E-00 - Cold Start Engine Exhaust Temperature Too Low. U0402-00 - Implausible Data Received From TCM. P0299-00 - Turbocharger Underboost Condition. P0402-00 - EGR Flow Excessive Detected. P249C-00 - Excessive Time To Enter Closed Loop Reductant Injection Control. P208B-00 - Reductant Pump 1 Control Performance. P20C6-00 - Reductant Heater 4 Control Circuit Performance. P245B-00 - EGR Cooler Bypass Control Circuit Performance. In addition, customers may experience the following concern:Some vehicles may have experienced a slight engine hesitation or lag inacceleration from engine startup until the engine and exhaust warmed up. This update is intended to reduce the hesitation or lag in accelerationfrom engine startup. Other software enhancement.Ability to enable the ?Fuel System Cleaning? routine in wiTECH.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs):P0133-00 - O2 Sensor 1/1 Slow Response. P20EE-00 - SCR NOX Catalyst Efficiency Below Threshold Bank 1. P050E-00 - Cold Start Engine Exhaust Temperature Too Low. U0402-00 - Implausible Data Received From TCM. P0299-00 - Turbocharger Underboost Condition. P0402-00 - EGR Flow Excessive Detected. P249C-00 - Excessive Time To Enter Closed Loop Reductant Injection Control. P208B-00 - Reductant Pump 1 Control Performance. P20C6-00 - Reductant Heater 4 Control Circuit Performance. P245B-00 - EGR Cooler Bypass Control Circuit Performance. Other software enhancement.Ability to enable the ?Fuel System Cleaning? routine in wiTECH.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs):P0133-00 - O2 Sensor 1/1 Slow Response. P20EE-00 - SCR NOX Catalyst Efficiency Below Threshold Bank 1. P050E-00 - Cold Start Engine Exhaust Temperature Too Low. U0402-00 - Implausible Data Received From TCM. P0299-00 - Turbocharger Underboost Condition. P0402-00 - EGR Flow Excessive Detected. P249C-00 - Excessive Time To Enter Closed Loop Reductant Injection Control. P208B-00 - Reductant Pump 1 Control Performance. P20C6-00 - Reductant Heater 4 Control Circuit Performance. P245B-00 - EGR Cooler Bypass Control Circuit Performance. Other software enhancement.Ability to enable the ?Fuel System Cleaning? routine in wiTECH.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:GAS RECIRCULATION VALVE (EGR VALVE) · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
USB PORT, Media Hub For Android Auto and Apple Carplay issues, do not replace this part. Android Auto and Apple Carplay applications may not operate with the vehicle if an aftermarket cable is being used. Verify the functionality of these applications using an OEM Apple Lightning cable or an OEM provided USB cable for Android phones before performing any additional troubleshooting. For questions regarding Android Auto or Apply Carplay functionality, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
USB PORT, Media Hub For Android Auto and Apple Carplay issues, do not replace this part. Android Auto and Apple Carplay applications may not operate with the vehicle if an aftermarket cable is being used. Verify the functionality of these applications using an OEM Apple Lightning cable or an OEM provided USB cable for Android phones before performing any additional troubleshooting. For questions regarding Android Auto or Apply Carplay functionality, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Transmission Oil Pan, Heater (TMU), Tube or O-ring Applies to vehicles equipped with 8 speed transmissions only; if you have a leak that appears to be at the pan the use of proper leak detection is recommended. The fluid in the 8 speeds can be detected with a black light and there are aftermarket spray on leak detection materials to help ensure that the leak is properly diagnosed and not from another location such as cooler lines, heater tubes, or case porosity. Please note that the transmission pan gasket is available for many of the 8 speed applications FCA offers. Please review the available quick connect and transfer tube parts, as replacement of the TMU may not be required. If a TOC line connection is found to be the source, the quick connect may need replacement. If the leak source is coming from the connection of the TMU to the transmission, the transfer tube may need replacement. When parts are returned to the QEC the retaining clips (snap ring) for the quick disconnect fittings are missing. (This leaves a question as to whether the clips were missing from the assembly plant, or the technician removed them in order to make line removal easier.) Please return the clips with the transmission heater and note if they were not there to begin with. For any questions regarding transmission heater, contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Transmission Oil Pan, Heater (TMU), Tube or O-ring Applies to vehicles equipped with 8 speed transmissions only; if you have a leak that appears to be at the pan the use of proper leak detection is recommended. The fluid in the 8 speeds can be detected with a black light and there are aftermarket spray on leak detection materials to help ensure that the leak is properly diagnosed and not from another location such as cooler lines, heater tubes, or case porosity. Please note that the transmission pan gasket is available for many of the 8 speed applications FCA offers. Please review the available quick connect and transfer tube parts, as replacement of the TMU may not be required. If a TOC line connection is found to be the source, the quick connect may need replacement. If the leak source is coming from the connection of the TMU to the transmission, the transfer tube may need replacement. When parts are returned to the QEC the retaining clips (snap ring) for the quick disconnect fittings are missing. (This leaves a question as to whether the clips were missing from the assembly plant, or the technician removed them in order to make line removal easier.) Please return the clips with the transmission heater and note if they were not there to begin with. For any questions regarding transmission heater, contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.
Source components: AIR BAGS · BACK OVER PREVENTION · ENGINE AND ENGINE COOLING · FUEL SYSTEM, GASOLINE · POWER TRAIN · SEATS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Transmission Oil Pan, Heater (TMU), Tube or O-ring Applies to vehicles equipped with 8 speed transmissions only; if you have a leak that appears to be at the pan the use of proper leak detection is recommended. The fluid in the 8 speeds can be detected with a black light and there are aftermarket spray on leak detection materials to help ensure that the leak is properly diagnosed and not from another location such as cooler lines, heater tubes, or case porosity. Please note that the transmission pan gasket is available for many of the 8 speed applications FCA offers. Please review the available quick connect and transfer tube parts, as replacement of the TMU may not be required. If a TOC line connection is found to be the source, the quick connect may need replacement. If the leak source is coming from the connection of the TMU to the transmission, the transfer tube may need replacement. When parts are returned to the QEC the retaining clips (snap ring) for the quick disconnect fittings are missing. (This leaves a question as to whether the clips were missing from the assembly plant, or the technician removed them in order to make line removal easier.) Please return the clips with the transmission heater and note if they were not there to begin with. For any questions regarding transmission heater, contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CONDENSER, Air Conditioning CONDITION 1: If it is determined that the A/C compressor does not engage due to a refrigerant leak at the receiver/drier plug on the A/C condenser, order the receiver/drier plug kit P/N 68447796A$ and follow the repair instructions included on the instruction sheet. CONDITION 2: For stock at the dealership of the below Part Number level or older ONLY, use kit 68447796A$ to change the desiccant BAG and the desiccant bag access PLUG before installing the Cooler on the vehicle. 52014588AD level and older only. 52014609AC level and older only. 52014632AC level and older only. 52014797AG level and older only. 52014948AE level and older only. 52014978AF level and older only.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CONDENSER, Air Conditioning CONDITION 1: If it is determined that the A/C compressor does not engage due to a refrigerant leak at the receiver/drier plug on the A/C condenser, order the receiver/drier plug kit P/N 68447796A$ and follow the repair instructions included on the instruction sheet. CONDITION 2: For stock at the dealership of the below Part Number level or older ONLY, use kit 68447796A$ to change the desiccant BAG and the desiccant bag access PLUG before installing the Cooler on the vehicle. 52014588AD level and older only. 52014609AC level and older only. 52014632AC level and older only. 52014797AG level and older only. 52014948AE level and older only. 52014978AF level and older only.
Source components: ELECTRICAL SYSTEM · VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CONDENSER, Air Conditioning CONDITION 1: If it is determined that the A/C compressor does not engage due to a refrigerant leak at the receiver/drier plug on the A/C condenser, order the receiver/drier plug kit P/N 68447796A$ and follow the repair instructions included on the instruction sheet. CONDITION 2: For stock at the dealership of the below Part Number level or older ONLY, use kit 68447796A$ to change the desiccant BAG and the desiccant bag access PLUG before installing the Cooler on the vehicle. 52014588AD level and older only. 52014609AC level and older only. 52014632AC level and older only. 52014797AG level and older only. 52014948AE level and older only. 52014978AF level and older only.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:APPLIANCE:AIR CONDITIONER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Improperly Installed Exhaust Gas Recirculation (EGR) Valve This bulletin involves removing and inspecting the vacuum tube, EGR tube gaskets, tube flange mounting bolts and possibly replacing the EGR tube gaskets and torquing the flange bolts. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set:P245B - EGR-Cooler-Bypass-Control-Circuit-Performance. The customer may also notice one or more of the following:An exhaust smell in the cabin. A whistle noise coming from the engine compartment.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Improperly Installed Exhaust Gas Recirculation (EGR) Valve This bulletin involves removing and inspecting the vacuum tube, EGR tube gaskets, tube flange mounting bolts and possibly replacing the EGR tube gaskets and torquing the flange bolts. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set:P245B - EGR-Cooler-Bypass-Control-Circuit-Performance. The customer may also notice one or more of the following:An exhaust smell in the cabin. A whistle noise coming from the engine compartment.