2025 Nissan
PATHFINDERProblems & recalls

AEB WARNING WITH ONE OR MORE CURRENT DTCS STORED IN THE ADAS CONTROL UNIT 2, AND/OR THE LASER/RADAR CONTROL UNIT IF YOU CONFIRM The front radar is inoperative, the AEB warning is displayed, and one or more of the following DTCs are stored as CURRENT: · U2752-88 for “Ethernet circuit” stored in the ADAS control unit 2, · U275F-88 for “Ethernet circuit” stored in the LASER/RADAR (DISTANCE SENSOR) control unit, OR · C2589-86 for “TCM” stored in the LASER/RADAR (DISTANCE SENSOR) control unit, AND/OR · C258E-86 for “ABS” stored in the LASER/RADAR (DISTANCE SENSOR) control unit. ACTION 1. Confirm the current Distance Sensor control unit part number. 2. Reprogram the Distance Sensor control unit, if applicable. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.

Components: SERVICE BRAKES. Confirm detailed applicability in the original document.

FUEL FILLER TUBE LOWER SEAL IS LEAKING AND DTC P0456 IS STORED IN THE ECM This bulletin is no longer active. Please discard previous versions of NTB26-006.

Components: FUEL/PROPULSION SYSTEM. Confirm detailed applicability in the original document.

CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Infiniti by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).

Components: STRUCTURE:BODY. Confirm detailed applicability in the original document.

CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).

Components: STRUCTURE:BODY. Confirm detailed applicability in the original document.

CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).

Components: STRUCTURE:BODY. Confirm detailed applicability in the original document.

FUEL FILLER TUBE LOWER SEAL IS LEAKING AND DTC P0456 IS STORED IN THE ECM IF YOU CONFIRM The vehicle has a visible leak with a smoke machine test coming from the fuel filler tube lower seal, AND DTC P0456 is stored as “Active”, “Past”, or “Pending” in the ECM. ACTION 1. Remove the supplied funnel from the rear of the vehicle or trunk. 2. Insert the funnel completely in the fuel filler tube and remove completely five (5) times. 3. Re-check the fuel filler tube lower seal with a smoke machine to determine visually if any leak is present. 4. If the fuel filler lower seal continues to leak, replace the fuel filler tube. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.

Components: FUEL/PROPULSION SYSTEM. Confirm detailed applicability in the original document.

METAL TICKING NOISE AT B-PILLAR IF YOU CONFIRM A metallic ticking noise is coming from the driver (LH) side and/or passenger (RH) side B-Pillar when driving the vehicle on various road surfaces. ACTION Refer to the SERVICE INFORMATION in this bulletin to adjust the inner support of the affected B-Pillar. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.

Components: STRUCTURE:BODY. Confirm detailed applicability in the original document.

VENT CONTROL VALVE IN ACTIVE TEST INOPERATIVE IN CONSULT 4 SERVICE INFORMATION An issue in CONSULT 4 has been identified in “EVAP system close” in Work support. · After selecting the "EVAP system close" in Work support, the “VENT CONTROL/V” in Active test becomes non-functional temporarily. · When selecting “EVAP system close” operation in Work support, wait 10 minutes before starting “VENT CONTROL/V” Active test or cycle the IGN switch ON/OFF for “VENT CONTROL/V” Active test to be operational. HINT: This bulletin applies to model years that use CONSULT 4 only.

Components: ENGINE. Confirm detailed applicability in the original document.

STEERING WHEEL SWITCH BUTTONS INOPERATIVE, STICKING, OR NOT CLICKING WHEN PRESSED IF YOU CONFIRM The customer states that any of the steering wheel switch buttons are inoperative, sticking, or not clicking when pressed. ACTION Follow the SERVICE PROCEDURE to: 1. Remove the steering wheel assembly. 2. Replace the switch assembly on the steering wheel assembly. HINT: The switch assembly includes switches for both sides of the steering wheel. 3. Reinstall the steering wheel assembly. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair. This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

Campaign / software reference: EL25-001A

Components: ELECTRICAL SYSTEM. Confirm detailed applicability in the original document.

ACTION Date: October 2, 2025 To: FOMs, DOMs, RAMs, & RGMs Subject: LAUNCH PD172 PMA55 Multi Model Monroney Bumper Label – QA – Dealer Announcement and Procedure ACTION: FOMs & DOMs are asked to ensure that dealers are aware of this new campaign information. Dealer Announcement: To ensure continued customer satisfaction and confidence, Nissan is conducting a quality action on certain specific model year 2025 ARIYA, 2024-2025 Pathfinder, 2024-2026 Rogue, 2024-2025 Murano and 2025-2026 Kicks vehicles, as identified in Service Comm and DBS National Service History. This action updates the Monroney labels to reflect corrected bumper labeling requirements for California and Hawaii. Dealers will replace original Monroney labels with corrected Monroney labels. Nissan will send VIN-specific corrected labels to address affected vehicles in dealer inventory. New labels will begin shipping via Federal Express Wednesday, October 1, 2025. Dealers will replace original Monroney labels with corrected Monroney labels. Affected vehicles are subject to stop sale and are either currently in dealer inventory or assigned and in transit to the dealer. What Dealers Should Do: PLEASE FOLLOW THE ATTACHED INSTRUCTIONS: 1.Verify if vehicles are affected by this quality action using Service Comm or DBS National Service History – Open Campaigns I.D. PD172 & PMA55 •New vehicles in dealer inventory can also be identified using DBS (Sales-> Vehicle Inventory, and filter by Open Campaign). Refer to NPSB 15-460 for additional information •Some vehicles may still be in transit. Please continue to check newly arriving inventory for applicability. 2.Please do not drive, loan, sell or trade the specific vehicles in dealer inventory subject to this quality action. 3.Use the attached procedure to remedy any vehicles affected by this quality action prior to sale. 4.If you have exchanged or traded one of the affected vehicles to another Nissan dealer, please forward the corrected Monroney label to the current dealer upon receipt so it can be attached to the vehicle. •If a vehicle has been retailed, dispose of the corrected Monroney label using the same procedure as for destroying the original Monroney label. 5.The service department should submit the applicable warranty claim for the action performed to close the campaign in Service Comm and release the vehicle.

Campaign / software reference: PD172, PMA55

Components: STRUCTURE:BODY. Confirm detailed applicability in the original document.

EXCESS DUST ENTERING CABIN WHILE DRIVING ON DIRT ROADS IF YOU CONFIRM That while driving on dirt roads with all doors and windows closed, that there is excessive dust intrusion into the vehicle’s cabin that is settling on the inside of the doors. ACTION Refer to the SERVICE PROCEDURE in the bulletin to: 1. Install Butyl Patches around the door seals of driver (LH) side and passenger (RH) side front and rear doors. 2. Install drain plugs into door drains of driver (LH) side and passenger (RH) side front and rear doors.

Components: STRUCTURE:BODY. Confirm detailed applicability in the original document.