2023 Nissan
PATHFINDERProblems & recalls

AEB WARNING WITH ONE OR MORE CURRENT DTCS STORED IN THE ADAS CONTROL UNIT 2, AND/OR THE LASER/RADAR CONTROL UNIT IF YOU CONFIRM The front radar is inoperative, the AEB warning is displayed, and one or more of the following DTCs are stored as CURRENT: · U2752-88 for “Ethernet circuit” stored in the ADAS control unit 2, · U275F-88 for “Ethernet circuit” stored in the LASER/RADAR (DISTANCE SENSOR) control unit, OR · C2589-86 for “TCM” stored in the LASER/RADAR (DISTANCE SENSOR) control unit, AND/OR · C258E-86 for “ABS” stored in the LASER/RADAR (DISTANCE SENSOR) control unit. ACTION 1. Confirm the current Distance Sensor control unit part number. 2. Reprogram the Distance Sensor control unit, if applicable. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.

Components: SERVICE BRAKES. Confirm detailed applicability in the original document.

FUEL FILLER TUBE LOWER SEAL IS LEAKING AND DTC P0456 IS STORED IN THE ECM This bulletin is no longer active. Please discard previous versions of NTB26-006.

Components: FUEL/PROPULSION SYSTEM. Confirm detailed applicability in the original document.

CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Infiniti by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).

Components: STRUCTURE:BODY. Confirm detailed applicability in the original document.

CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).

Components: STRUCTURE:BODY. Confirm detailed applicability in the original document.

CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).

Components: STRUCTURE:BODY. Confirm detailed applicability in the original document.

FUEL FILLER TUBE LOWER SEAL IS LEAKING AND DTC P0456 IS STORED IN THE ECM IF YOU CONFIRM The vehicle has a visible leak with a smoke machine test coming from the fuel filler tube lower seal, AND DTC P0456 is stored as “Active”, “Past”, or “Pending” in the ECM. ACTION 1. Remove the supplied funnel from the rear of the vehicle or trunk. 2. Insert the funnel completely in the fuel filler tube and remove completely five (5) times. 3. Re-check the fuel filler tube lower seal with a smoke machine to determine visually if any leak is present. 4. If the fuel filler lower seal continues to leak, replace the fuel filler tube. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.

Components: FUEL/PROPULSION SYSTEM. Confirm detailed applicability in the original document.

STEERING WHEEL SWITCH BUTTONS INOPERATIVE, STICKING, OR NOT CLICKING WHEN PRESSED IF YOU CONFIRM The customer states that any of the steering wheel switch buttons are inoperative, sticking, or not clicking when pressed. ACTION Follow the SERVICE PROCEDURE to: 1. Remove the steering wheel assembly. 2. Replace the switch assembly on the steering wheel assembly. HINT: The switch assembly includes switches for both sides of the steering wheel. 3. Reinstall the steering wheel assembly. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair. This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

Campaign / software reference: EL25-001A

Components: ELECTRICAL SYSTEM. Confirm detailed applicability in the original document.

EXCESS DUST ENTERING CABIN WHILE DRIVING ON DIRT ROADS IF YOU CONFIRM That while driving on dirt roads with all doors and windows closed, that there is excessive dust intrusion into the vehicle’s cabin that is settling on the inside of the doors. ACTION Refer to the SERVICE PROCEDURE in the bulletin to: 1. Install Butyl Patches around the door seals of driver (LH) side and passenger (RH) side front and rear doors. 2. Install drain plugs into door drains of driver (LH) side and passenger (RH) side front and rear doors.

Components: STRUCTURE:BODY. Confirm detailed applicability in the original document.

DRIVABILITY CONCERNS AT HIGHWAY SPEEDS AND ON INCLINES IF YOU CONFIRM A lugging / shutter / judder at highway speeds, especially on slight inclines, ACTION Reprogram the Engine Control Module (ECM).

Components: ENGINE. Confirm detailed applicability in the original document.

AUTOMATIC EMERGENCY BRAKING WARNING LIGHT BLINKING APPLIED SYSTEMS: Vehicles equipped with a lane camera (see Figure 1) SERVICE INFORMATION If the Automatic Emergency Braking (AEB) warning light or is blinking (but not illuminated steadily) or the customer states it is blinking, and there are no related DTCs, inspect the windshield. A blinking AEB warning light may occur under the following conditions:  When contamination or foreign material adhere to the lane camera viewing window on the windshield.  When driving while it is snowing or when frost forms on the lane camera viewing window on the windshield.  When the lane camera viewing window on the windshield is temporarily fogged up. Figure 1 Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. HINT: o Refer to the applicable ESM for diagnosis if DTCs are present in the Laser/Radar, ICC/ADAS, or Lane Camera systems. o For further information:  Refer to the following pages.  Use the search keyword “blinking” in the ESM.

Components: ELECTRICAL SYSTEM · FORWARD COLLISION AVOIDANCE: AUTOMATIC EMERGENCY BRAKING · SERVICE BRAKES. Confirm detailed applicability in the original document.

INTELLIGENT CRUISE CONTROL INOPERATIVE AND AEB/FEB WARNING LIGHT ON OR RADAR OBSTRUCTION MESSAGE DISPLAYED WITH DTC C1A16 OR C2582 IF YOU CONFIRM IMPORTANT: The purpose of ACTION (on the next page) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair. Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. The customer states that the ICC stopped working while driving, OR The customer states that the AEB/FEB warning light is ON, or turned ON, while driving (Figure 1), OR The message “Unavailable Front Radar Obstruction” or “Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner's Manual” has displayed while driving (Figure 2). AND DTC C1A16, C1A16-97, C2582, or C2582-97 is the ONLY DTC stored. Figure 1 Figure 2 This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner’s Manual

Components: ELECTRICAL SYSTEM · FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL · FORWARD COLLISION AVOIDANCE: AUTOMATIC EMERGENCY BRAKING · SERVICE BRAKES. Confirm detailed applicability in the original document.

DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. IF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored, AND OCS zero point reset cannot be performed, (continued on the next page)

Components: AIR BAGS. Confirm detailed applicability in the original document.