Original record summaries, dates and identifiers for this model-year. Records 101–200 of 202, ordered newest first. Dated records on this page: Jun 12, 2015–May 13, 2019.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
May 13, 2019Service Bulletin/Repair Instructions
NTB19-038
NHTSA communication ID: 10161346
NHTSA source summary · Original PDF not reviewed by Recallfolio
DEAD PEDAL REPLACEMENT SERVICE INFORMATION If the dead pedal needs to be replaced for any reason, it is no longer necessary to replace the front floor trim (carpet). The dead pedal is now available as a service part. NOTE: Do not replace the carpet if only the dead pedal is needed. ACTION Follow the SERVICE PROCEDURE on the next page to replace ONLY the Dead pedal. NOTE: Dead pedal is listed in PARTS INFORMATION on the last page.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2016-2018 NISSAN; MIL ON WITH DTC P0171, P0174, P2097, AND/OR P2099 This bulletin applies to Altima vehicles equipped with VQ35 engine only. IF YOU CONFIRM The MIL is ON with one or more of the following Air/Fuel (A/F) Sensor DTCs stored: - P0171 (Fuel Injection System Function) - P0174 (Fuel Injection System Function) - P2097 (A/F SENSOR 1) - P2099 (A/F SENSOR 1) ACTION 1. Perform the appropriate diagnostic procedure outlined in the Electronic Service Manual (ESM). 2. Refer to Table A on page 2 and page 3 to confirm if Electronic Control Module (ECM) reprogramming is needed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CVT / TCM CALIBRATION DATA ?WRITE? PROCEDURE This bulletin applies only to vehicles equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CVT / TCM CALIBRATION DATA ?WRITE? PROCEDURE This bulletin applies only to vehicles equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CVT FLUID LEVEL QUICK CHECK GAUGE This bulletin applies only to vehicles equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN; MIL ON WITH DTC P219A AND/OR P219B STORED This bulletin applies to Titan XD vehicles equipped with a VK56D gas engine only. SERVICE INFORMATION If the MIL is ON and DTC P219A (AIR FUEL RATIO IMBALANCE B1) and/or P219B (AIR FUEL RATIO IMBALANCE B2) is stored: - DO NOT replace the Air Fuel Ratio (A/F) sensor. - Refer to the applicable Electronic Service Manual (ESM) and follow the diagnostic procedure for DTC P219A and/or P219B.
NHTSA source summary · Original PDF not reviewed by Recallfolio
INTELLIGENT KEY BUTTONS INOPERATIVE BUT REQUEST SWITCHES WORK This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin does NOT apply to LEAF vehicles and Titan XD vehicles with V8 diesel engine. This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
ALL MODEL YEAR 2012 AND NEWER NISSAN VEHICLES; EVAP LEAK DTC P0442, P0455, P0456 INFORMATION This bulletin does NOT apply to LEAF vehicles and Titan XD vehicles with V8 diesel engine. This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
OBD II EVAP Tube Warranty Enhancement The update below was sent out to Regions and Dealers in August of this year. We are re-circulating this update to make regional and dealer personnel aware that we are re-notifying customers at this time.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN; FUEL TANK IS EXTREMELY DIFFICULT TO FILL This bulletin applies to Titan XD vehicles with a gas engine. The update below was sent out to Regions and Dealers in August of this year. We are re-circulating this update to make regional and dealer personnel aware that we are re-notifying customers at this time.
NHTSA source summary · Original PDF not reviewed by Recallfolio
AIR BAG WARNING LIGHT FLASHING INDICATING SYSTEM DIAGNOSTIC MODE IF YOU CONFIRM The air bag warning light is flashing slowly (repeating 2 seconds ON, 2 seconds OFF). NOTE: If this should occur, the Air Bag Diagnosis Sensor Unit is in Diagnostic Mode and needs to be returned to User Mode. ACTION 1. Use CONSULT-III plus to check for Air Bag DTCs and perform repairs as needed. 2. Return the Air Bag Diagnosis Sensor Unit to User Mode.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN; VIBRATION AND/OR NOISE WHEN MAKING LOW SPEED TURNS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CVT / TCM CALIBRATION DATA ?WRITE? PROCEDURE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CVT FLUID LEVEL QUICK CHECK GAUGE This bulletin applies only to vehicles equipped with a CVT (Continuously Variable Transmission). This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
Source components: ELECTRICAL SYSTEM · ENGINE · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN; SIGNAL TECH-II INTELLIGENT KEY BATTERY TEST AND SIGNAL CHECK This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN; VIBRATION AND/OR NOISE WHEN MAKING LOW SPEED TURNS This bulletin applies only to vehicles equipped with AWD (All-Wheel Drive) or 4WD (4-Wheel Drive). This bulletin has been amended. The APPLIED VEHICLES and PARTS INFORMATION sections have been revised. No other changes have been made. Please discard all previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN; FUEL TANK IS EXTREMELY DIFFICULT TO FILL This bulletin applies to Titan XD vehicles with a gas engine. This bulletin has been amended. Changes have been made throughout. It is necessary for you to read this revised procedure to properly perform this action. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN; FUEL TANK IS EXTREMELY DIFFICULT TO FILL This bulletin applies to Titan XD vehicles with a gas engine. This bulletin has been amended. Changes have been made throughout. It is necessary for you to read this revised procedure to properly perform this action. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CVT FLUID LEVEL QUICK CHECK GAUGE This bulletin applies only to vehicles equipped with a Continuously Variable Transmission (CVT). SERVICE INFORMATION Special tool CVT8 Oil Level Quick Check Gauge (J-51155) is now available. Each dealer has been shipped one of these tools. Additional tools can be obtained from Tech?Mate at 1-800-662-2001. Refer to the SERVICE PROCEDURE on the next page to determine how to perform a CVT fluid quick level check.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CVT FLUID LEVEL CHECK SERVICE INFORMATION This bulletin applies only to vehicles equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended. The APPLIED VEHICLES and SERVICE INFORMATION sections have been revised. No other changes have been made. Please discard all previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CVT FLUID LEVEL CHECK SERVICE INFORMATION This bulletin applies only to vehicles equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended. The APPLIED VEHICLES and SERVICE INFORMATION sections have been revised. No other changes have been made. Please discard all previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
FOG LAMP AND/OR HEADLAMP FOGGING This bulletin has been amended to add Fog Lamps and modify one step in the flow chart on page 3. No other changes have been made. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
MIL ON WITH P0603 STORED FOR ECM BACK UP CIRCUIT This bulletin does NOT apply to Titan equipped with Cummins V8 Diesel engine. This bulletin has been amended to add a NOTE in the Applied Vehicles. No other changes have been made. Please discard previous versions of this bulletin.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
INTELLIGENT KEY NOT DETECTED / ENGINE WILL NOT START This bulletin has been amended to update the Applied Vehicles. No other changes were made. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
WHEEL BALANCING SERVICE INFORMATION This bulletin has been amended. The publication date has been revised to include the latest models and model years. No other changes have been made. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
PATHFINDER, ALTIMA, MAXIMA, MURANO AND QUEST; CVT JUDDER AND DTC P17F0 OR P17F1 STORED This bulletin applies only to vehicles equipped with a V6 engine. This bulletin has been amended to change the Claims Information on page 103. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
PATHFINDER, ALTIMA, MAXIMA, MURANO AND QUEST; CVT JUDDER AND DTC P17F0 OR P17F1 STORED This bulletin applies only to vehicles equipped with a V6 engine. This bulletin has been amended to add Quest to Applied Vehicles and information related to Quest on pages 25, 100, 102, 103 and 105. Please discard previous versions of this bulletin. IMPORTANT: You must read the entire bulletin to properly perform this repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
REVISED WHEEL ALIGNMENT SPECIFICATIONS This bulletin has been amended to add 2018 Versa Sedan and 2018 Versa Note. No other changes have been made. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
PATHFINDER, ALTIMA, MAXIMA, MURANO; CVT JUDDER AND DTC P17F0 OR P17F1 STORED This bulletin applies to Altima vehicles equipped with a V6 engine only. This bulletin has been amended to change the parts table information on page 101. Please discard previous versions of this bulletin. IMPORTANT: You must read the entire bulletin to properly perform this repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
PATHFINDER, ALTIMA, MAXIMA, MURANO; CVT JUDDER AND DTC P17F0 OR P17F1 STORED This bulletin applies to Altima vehicles equipped with a V6 engine only. This bulletin has changed. You must read the entire bulletin to properly perform this repair. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
WHEEL BALANCING SERVICE INFORMATION This bulletin has been amended. The publication date has been revised to include the latest models and model years. No other changes have been made. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2013 - 2017 PATHFINDER; RADIATOR SHROUD AND COOLING FAN ASSEMBLY REPLACEMENT PROCEDURE SERVICE INFORMATION When replacing the radiator shroud and cooling fan assembly for any reason, the engine coolant, air cleaner case, and air duct does not need to be removed as part of the procedure. Use this SERVICE PROCEDURE (in place of the ESM) and the CLAIMS INFORMATION in this bulletin. The ESM will be updated at a later date.
Source components: ENGINE AND ENGINE COOLING:COOLING SYSTEM · ENGINE AND ENGINE COOLING:COOLING SYSTEM:RADIATOR ASSEMBLY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2013 ? 2016 PATHFINDER OCCUPANT CLASSIFICATION SYSTEM RETROFIT This bulletin has been amended. Pages 18 and 20 have been revised. No other changes have been made. Please discard all previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2013 ? 2017 ALTIMA AND PATHFINDER; SHIFT LOCK SOLENOID REMOVAL AND INSTALLATION This bulletin has been amended to change the PFP in the Claims Information. Please discard all previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CVT FLUID LEVEL CHECK SERVICE INFORMATION This bulletin applies only to vehicles equipped with a Continuously Variable Transmission (CVT). This bulletin has been amended. The APPLIED VEHICLES section has been revised. No other changes have been made. Please discard all previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. The APPLIED VEHICLES and CLAIMS INFORMATION sections have been revised. No other changes have been made. Please discard previous versions of this bulletin.
Source components: SERVICE BRAKES, AIR:SUPPLY:CHECK VALVE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN; OIL LEAKING AROUND VALVE TIMING CONTROL SOLENOID VALVE This bulletin applies only to Maxima, Quest, Altima Coupe, Altima Sedan, Pathfinder and Murano vehicles with a 6-cylinder engine and Titan/Titan XD vehicles with a V8 gasoline engine. This bulletin has been amended. The PARTS INFORMATION section has been revised. No other changes have been made. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2013 ? 2016 PATHFINDER OCCUPANT CLASSIFICATION SYSTEM RETROFIT This bulletin has been amended. The CLAIMS INFORMATION section has been revised. No other changes have been made. Please discard all previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
DTC P0036 DIAGNOSTIC INFORMATION This bulletin applies only to Altima and Pathfinder vehicles with a 6-cylinder engine. SERVICE INFORMATION The Electronic Service Manual (ESM) information for DTC P0036 may be inaccurate or incomplete for the Applied Vehicles. If an Applied Vehicle stores a DTC P0036, follow diagnostic procedures in the ESM for Bank 2 A/F Sensor Heater open or shorted.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THUNK SOUND ON FIRST FEW ACCELERATIONS OF THE DAY This bulletin applies only to Altima, Murano, and Pathfinder vehicles equipped with 6-cylinder engine. This bulletin has been amended. Changes have been made throughout. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THEFT ALARM SOUNDS WHEN VEHICLE IS LOCKED, UNLOCKED, OR DOOR/TRUNK OPENED IF YOU CONFIRM Intermittently, the theft alarm triggers (horn sounds and lights flash) when one of the following occur: - Using the lock, unlock, or trunk open function on the Intelligent Key - Pushing a handle request switch (door or trunk) - Opening a door or the trunk with the vehicle unlocked and CONSULT-III plus (C-III plus) shows the last item to trigger the theft alarm is BATTERY. - Refer to Check Last Item to Trigger Theft Alarm on the next page. ACTION Replace the Body Control Module (BCM). - Refer to the Electronic Service Manual, section BCS-Body Control Systems, for replacement information. - Use the new BCM listed in the PARTS INFORMATION section.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. The APPLIED VEHICLES section has been revised. No other changes have been made. Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2013 ? 2017 ALTIMA AND PATHFINDER; SHIFT LOCK SOLENOID REMOVAL AND INSTALLATION SERVICE INFORMATION If an Applied Vehicle needs the shift lock solenoid replaced for any reason, use the Service Procedure in this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
PATHFINDER, QUEST, MURANO, MAXIMA, ALTIMA V6; CVT JUDDER AND DTC P17F0 OR P17F1 STORED This bulletin has been amended to remove 2013-2014 Pathfinder from applied vehicles. No other changes have been made. Please discard all previous versions of this bulletin.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CVT / TCM CALIBRATION DATA "WRITE" PROCEDURE This bulletin does not apply to Pathfinder Hybrid, Murano Hybrid or Rogue Hybrid This bulletin has been amended. APPLIED VEHICLES has been updated. SERVICE INFORMATION has been amended. A REPAIR TABLE has been added. Procedural steps have been added to SERVICE PROCEDURE. Discard all previous versions of this bulletin.
Source components: ELECTRICAL SYSTEM:SOFTWARE · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN; PROCEDURE TO CLEAN CVT TRANSMISSION FLUID COOLERS This bulletin has been amended. The APPLIED VEHICLES section has been revised. No other changes have been made. Please discard previous versions of this bulletin.
Source components: POWER TRAIN · POWER TRAIN:AUTOMATIC TRANSMISSION · POWER TRAIN:AUTOMATIC TRANSMISSION:COOLING UNIT AND LINES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
REVISED WHEEL ALIGNMENT SPECIFICATIONS SERVICE INFORMATION For the Applied Vehicles, some wheel alignment specifications listed in the Front Suspension (FSU) and Rear Suspension (RSU) sections of the Electronic Service Manual (ESM) have been revised. Updated ESMs will be distributed to the field as quickly as possible. Until the updated ESMs are made available, please use the corrected specifications listed in this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN; OIL LEAKING AROUND VALVE TIMING CONTROL SOLENOID VALVE This bulletin applies to vehicles equipped with 6-cylinder engines. For Titan and Titan XD, this bulletin applies only vehicles equipped with gasoline engines. This bulletin has been amended in the PARTS INFORMATION and CLAIMS INFORMATION sections. Discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NAVIGATION SYSTEM REBOOTS WHEN SXM TRAFFIC IS ENABLED This bulletin applies only to vehicles located in the state of Oregon. IF YOU CONFIRM The Navigation system in an Applied Vehicle reboots when SXM Traffic is enabled. NOTE: Perform the steps in this bulletin ONLY if the above condition occurs while the vehicle is in the state of Oregon. ACTION Update the Navigation system software using the DVD shown on page 2.
NHTSA source summary · Original PDF not reviewed by Recallfolio
ENHANCED DIAGNOSTIC LOGIC FOR CVT This bulletin has been amended to add model years to the Applied Vehicles and part numbers to Table A. No other changes have been made. Please discard all previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
PATHFINDER, QUEST, MURANO, MAXIMA, ALTIMA V6; CVT JUDDER AND DTC P17F0 OR P17F1 STORED This bulletin has been amended to add applied vehicles and change the Parts Information. No other changes have been made. Please discard all previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN; FUEL TANK IS SLOW OR DIFFICULT TO FILL IF YOU CONFIRM The fuel tank is slow or difficult to fill (filling nozzle shuts off before tank is full). IMPORTANT: Make sure this incident has been duplicated at a gas station by dealer service staff. ACTION Perform the Service Procedure in this bulletin, starting on the next page.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2014 - 2016 PATHFINDER OCCUPANT CLASSIFICATION SYSTEM RETROFIT SERVICE INFORMATION The information in this bulletin is provided for customers who have concerns with their Occupant Classification System (OCS) operation after all campaigns have been completed. Follow the steps in this bulletin to determine if this OCS retrofit procedure is applicable to the vehicle you are working on.
NHTSA source summary · Original PDF not reviewed by Recallfolio
POWER MOONROOF INITIALIZATION SERVICE INFORMATION This bulletin has been amended. The APPPLIED VEHICES section and step 3 on page 3 have been revised. No other changes have been made. Please discard all previous versions.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN; OIL LEAKING AROUND VALVE TIMING CONTROL SOLENOID VALVE This bulletin applies only to Maxima, Quest, Altima Coupe, Altima, Pathfinder and Murano vehicles equipped with V6 engine OR Titan/Titan XD equipped with VK56 engine IF YOU CONFIRM Engine oil is leaking from a valve timing control solenoid valve, And The valve timing control solenoid valve operates correctly and is not externally damaged. ACTION Replace the valve timing control solenoid valve O-ring with a new one using the Service Procedure starting on page 2.
NHTSA source summary · Original PDF not reviewed by Recallfolio
PATHFINDER, MURANO, AND ROGUE; FLUID LEAK CAUSED BY TRANSFER ASSEMBLY RIGHT SIDE DRIVE SHAFT SEAL This bulletin applies only to AWD equipped vehicles. IF YOU CONFIRM Fluid is leaking from the right side of the transfer assembly (see Figure 1). NOTE: The fluid leak is not caused by the seal shown in Figure 1. ACTION 1. DO NOT REPLACE the transfer assembly. 2. Reseal the transfer assembly. - Refer to the Electronic Service Manual (ESM), section DLN ? Driveline, for transfer assembly removal, reseal, and installation information. - Refer to page 2 and 3 for additional information. CAUTION: Be careful not to damage the transfer assembly right side drive shaft seal when reinstalling the drive shaft.
Source components: POWER TRAIN:DRIVELINE:DRIVESHAFT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
POWER BACK DOOR CALIBRATION This bulletin has been amended. Step 15 has been revised. No other changes have been made. Please discard previous versions of this bulletin.
Source components: STRUCTURE:BODY:HATCHBACK/LIFTGATE · STRUCTURE:BODY:HATCHBACK/LIFTGATE:HINGE AND ATTACHMENTS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
POWER BACK DOOR CALIBRATION The Applied Vehicles in this bulletin have been amended. No other changes have been made Please discard previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
PLASTIC INTERIOR TRIM PROTECTIVE COVERING REMOVAL SERVICE INFORMATION Vehicles are delivered with plastic interior trim protective covering on the front and rear seats, front and rear door panel finishers, steering wheel, and sun visors (see examples on page 2). When removing the protective covering, care must be used to avoid scuffs, scrapes, cuts, and other abrasive contact to interior trim components. DO NOT use sharp objects like razor blades, box cutters, knives, etc. when removing the plastic interior trim protective covering. IMPORTANT All soft trim described in this bulletin is on automatic return to NNA. Any trim found damaged in the way described in this bulletin will be charged back to the dealer.
NHTSA source summary · Original PDF not reviewed by Recallfolio
INTELLIGENT KEY NOT DETECTED / ENGINE WILL NOT START This bulletin has been amended to update the Applied Vehicles and make changes to the body of the bulletin. Please discard previous versions.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NISSAN; DIAGNOSIS INFORMATION FOR ABS DTC C1130 SERVICE INFORMATION When diagnosing for DTC C1130 (ENGINE SIGNAL): ECM related DTCs (P-codes) must be diagnosed, repaired, and DTCs erased first. - DTC C1130 is an ABS DTC that indicates an output signal of the ECM is not recognized. - Absent or incorrect ECM signals, that are indicated by corresponding P-codes, may trigger C1130 in the ABS control unit. - Some vehicle features that can be affected by absent or incorrect ECM signals are: - Forward Emergency Braking (FEB) - Intelligent Cruise Control (ICC) - VDC/ABS/TCS
NHTSA source summary · Original PDF not reviewed by Recallfolio
CVT FLUID LEVEL CHECK SERVICE INFORMATION This bulletin has been amended. The APPLIED VEHICLES section has been revised. No other changes have been made. Please discard all previous versions of this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"NISSAN; DOORS DIFFICULT TO CLOSE WITH TEMPERATURE BELOW FREEZING IF YOU CONFIRM: THE FOLLOWING INCIDENT, OR THE CUSTOMER REPORTS THIS INCIDENT: - THE VEHICLE HAS BEEN SETTING (NOT RUNNING) IN TEMPERATURES BELOW 14°F (-10°C) FOR AN EXTENDED PERIOD (SUCH AS OVERNIGHT). THEN - A SIDE DOOR IS OPENED. THEN - THE DOOR IS DIFFICULT TO CLOSE/LATCH, WILL NOT CLOSE/LATCH WITH NORMAL PRESSURE; REQUIRES ADDITIONAL EFFORT TO CLOSE/LATCH, OR THE DOOR MAY ONLY LATCH HALF WAY. THEN - THE DOOR WILL CLOSE/LATCH NORMALLY WHEN THE VEHICLE HAS WARMED UP (VEHICLE LEFT IN THE SUN, MOVED INDOORS, OR DRIVEN FOR SEVERAL MINUTES). NOTE: O THE ABOVE INCIDENT DOES NOT APPLY TO SLIDING SIDE DOORS OR A REAR HATCH (BACK DOOR). O THE ABOVE INCIDENT, IF IT SHOULD OCCUR, COULD BE CONFIRMED OR REPORTED FOR ONE OR MORE SIDE DOORS. ACTION REPLACE THE DOOR LOCK FOR THE AFFECTED DOOR. - DO NOT REPLACE ALL SIDE DOOR LOCKS AUTOMATICALLY. REPLACE ONLY THE DOOR LOCK OF THE DOOR(S) WITH THE INCIDENT AS DESCRIBED UNDER IF YOU CONFIRM. - REFER TO THE ELECTRONIC SERVICE MANUAL (ESM), SECTION DLK DOOR & LOCK FOR REPLACEMENT PROCEDURE."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"ENHANCED DIAGNOSTIC LOGIC FOR CVT PATHFINDER AND ALTIMA WITH V6 ENGINE ONLY IF YOU CONFIRM THE CUSTOMER REPORTS A TRANSMISSION JUDDER (SHAKE, SHUDDER, SINGLE OR MULTIPLE BUMPS OR VIBRATION). NOTE: A NEW DIAGNOSTIC LOGIC HAS BEEN ESTABLISHED TO ENHANCE THE DIAGNOSTIC PROCESS BY STORING DIAGNOSTIC TROUBLE CODES (DTCS) ON APPLIED VEHICLES. THE NEW DTCS ARE: P17F1 (CVT_JUDDER [C/U INSPECTION]) P17F0 (CVT_JUDDER [T/M INSPECTION]) ACTION 1. REFER TO PAGE 4, STEP 6 IN THE SERVICE PROCEDURE TO CONFIRM THIS BULLETIN APPLIES TO THE VEHICLE YOU ARE WORKING ON. 2. IF THIS BULLETIN APPLIES, REPROGRAM THE TCM (TRANSMISSION CONTROL MODULE)."
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"2016 MURANO, ROGUE AND PATHFINDER; AROUND VIEW MONITOR MIRROR CAMERA INOPERATIVE IF YOU CONFIRM - EITHER THE LEFT OR RIGHT AROUND VIEW MONITOR DOOR MIRROR CAMERA IS INOPERATIVE. NOTE: THE FOLLOWING DTCS MAY ALSO BE PRESENT: - U111B (SIDE CAMERA LH IMAGE SIGNAL CIRCUIT) DTC IS STORED. AND/OR - U111D (SIDE CAMERA RH IMAGE SIGNAL CIRCUIT) DTC IS STORED. ACTION CHECK THE SIDE CAMERA HARNESS CONNECTION BETWEEN THE SIDE CAMERA AND THE MIRROR HARNESS LOCATED INSIDE THE INOPERATIVE DOOR MIRROR. - IF THE HARNESS CONNECTOR IS NOT LATCHED (CAN BE DISCONNECTED BY A GENTLE TUG), SEAT THE CONNECTOR, CLEAR THE DTC AND RETEST. - IF THE HARNESS CONNECTOR IS LATCHED (CANNOT BE DISCONNECTED BY A GENTLE TUG) REFER TO THE ELECTRONIC SERVICE MANUAL (ESM) FOR FURTHER DIAGNOSTIC INFORMATION. NOTE: IF A SIDE CAMERA REQUIRES REPLACEMENT, DO NOT REPLACE THE ENTIRE MIRROR, REPLACE ONLY THE SIDE CAMERA."
Source components: BACK OVER PREVENTION: CAMERA SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"ALL MODEL YEAR 2012 AND NEWER NISSAN VEHICLES; EVAP LEAK DTC P0442, P0455, P0456 INFORMATION THIS BULLETIN HAS BEEN AMENDED. THE TITLE HAS BEEN REVISED, AND THE BULLETIN NOW INCLUDES VEHICLES IN PRODUCTION AS OF THE DATE OF THIS UPDATE. NO OTHER CHANGES HAVE BEEN MADE. PLEASE DISCARD ALL PREVIOUS VERSIONS OF THIS BULLETIN."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"REAR O2 SENSOR VOLUNTARY EMISSIONS RECALL CAMPAIGN ***** CAMPAIGN SUMMARY ***** NISSAN IS CONDUCTING A VOLUNTARY EMISSIONS RECALL CAMPAIGN TO UPDATE THE ELECTRONIC CONTROL MODULE (ECM) SOFTWARE ON CERTAIN MODEL YEAR 2016 NISSAN MAXIMA (A36), AND MODEL YEAR 2015-16 ALTIMA (L33), JUKE (F15), PATHFINDER (R52), MURANO (Z52) AND QUEST (E52) VEHICLES. UNDER CERTAIN CONDITIONS, THE REAR OXYGEN (O2) SENSOR SIGNAL COULD FAIL, RESULTING IN THE REAR OXYGEN (O2) SENSOR OBD MONITOR BEING DISABLED WITHOUT THE CUSTOMER BEING ALERTED. NISSAN PLANS TO BEGIN NOTIFYING OWNERS OF AFFECTED VEHICLES IN AUGUST, ASKING THEM TO BRING THEIR VEHICLES TO AN AUTHORIZED NISSAN DEALERSHIP. ***** WHAT DEALERS SHOULD DO**** 1. VERIFY IF VEHICLES ARE AFFECTED BY THIS VOLUNTARY EMISSION RECALL CAMPAIGN USING SERVICE COMM I.D. R1620. NOTE: NEW VEHICLES IN DEALER INVENTORY CAN BE ALSO BE IDENTIFIED USING DCS (SALES-> VEHICLE INVENTORY, AND FILTER BY OPEN CAMPAIGN). - REFER TO NPSB 15-460 FOR ADDITIONAL INFORMATION 2. THE SUBJECT VEHICLES ARE NOT ON SALES HOLD, BUT FOR CUSTOMER CONVENIENCE, DEALERS ARE ENCOURAGED TO PERFORM THIS CAMPAIGN ON ANY AFFECTED VEHICLES IN THEIR INVENTORY PRIOR TO SALE, LEASE, OR TRADE. 3. DEALERS SHOULD USE NTB16-073 TO CORRECT ANY VEHICLES SUBJECT TO THIS CAMPAIGN. 4. ONCE REPAIRED, DEALER SHOULD SUBMIT A WARRANTY CLAIM AND RELEASE THE VEHICLE."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"VOLUNTARY EMISSIONS RECALL CAMPAIGN ECM REPROGRAMMING INTRODUCTION NISSAN IS CONDUCTING A VOLUNTARY EMISSION RECALL CAMPAIGN ON CERTAIN MODEL YEAR 2015-2016 ALTIMA, 2015-2016 JUKE, 2016 MAXIMA, 2015-2016 MURANO, 2015-2016 QUEST, AND 2015-2016 PATHFINDER VEHICLES. NISSAN HAS DISCOVERED THAT THESE VEHICLES ARE EQUIPPED WITH AN ON-BOARD DIAGNOSTICS (OBD) CALIBRATION THAT, IF NOT REPAIRED, MAY NOT DETECT A REAR OXYGEN (O2) SENSOR SHORT-TO-GROUND OR SHORT-TO-BATTERY CONDITION. THE ECM (ENGINE CONTROL MODULE) WILL BE REPROGRAMMED. THIS SERVICE WILL BE PERFORMED AT NO CHARGE FOR PARTS OR LABOR. IDENTIFICATION NUMBER NISSAN HAS ASSIGNED IDENTIFICATION NUMBER R1620 TO THIS CAMPAIGN. THIS NUMBER MUST APPEAR ON ALL COMMUNICATIONS AND DOCUMENTATION OF ANY NATURE DEALING WITH THIS CAMPAIGN. DEALER RESPONSIBILITY IT IS THE DEALERS RESPONSIBILITY TO CHECK SERVICE COMM FOR THE CAMPAIGN STATUS ON EACH VEHICLE FALLING WITHIN THE RANGE OF THIS VOLUNTARY EMISSIONS RECALL WHICH FOR ANY REASON ENTERS THE SERVICE DEPARTMENT. THIS INCLUDES VEHICLES PURCHASED FROM PRIVATE PARTIES OR PRESENTED BY TRANSIENT (TOURIST) OWNERS AND VEHICLES IN A DEALERS INVENTORY."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"REMOTE ENGINE START NOT WORKING THIS BULLETIN HAS BEEN AMENDED. CHANGES HAVE BEEN MADE TO ITEMS 1, 4, AND 13 IN THE SUPPLEMENTAL DIAGNOSIS TABLE. NO OTHER CHANGES HAVE BEEN MADE. PLEASE DISCARD PREVIOUS VERSIONS OF THIS BULLETIN. SERVICE INFORMATION IF A CUSTOMER STATES THE REMOTE ENGINE START (RES) FEATURE OF AN APPLIED VEHICLE IS NOT WORKING, MAKE SURE THE SYSTEM IS PROPERLY SET TO OPERATE: -THE IGNITION IS TURNED OFF -THE SHIFT SELECTOR IS IN PARK (P) -THE HOOD/DOORS/TRUNK LID/LIFT GATE ARE COMPLETELY CLOSED -NO OTHER OF THE VEHICLES INTELLIGENT KEYS (I-KEYS) ARE INSIDE, OR WITHIN STARTING RANGE OF, THE VEHICLE -THE I-KEY/KEY FOB (KEY FOB) IS WITHIN THE OPERATING RANGE OF 197 FT OR 60 M IF THE ABOVE CONDITIONS ARE MET, RES SHOULD WORK. 1. POINT THE KEY FOB AT THE VEHICLE. 2. PRESS THE LOCK BUTTON. 3. PRESS AND HOLD THE RES BUTTON WITHIN FIVE (5) SECONDS OF PRESSING THE LOCK BUTTON, UNTIL THE TURN SIGNAL LIGHTS TURN ON. WHENEVER AN APPLIED VEHICLE HAS A CONCERN WITH THE REMOTE ENGINE START (RES) FEATURE NOT WORKING PROPERLY, MAKE SURE TO VERIFY THE INCIDENT BEFORE STARTING ANY DIAGNOSIS AND/OR REPLACING PARTS. FOR A BETTER UNDERSTANDING OF THE RES SYSTEM, REFER TO SECTION 3: PRE-DRIVING CHECKS AND ADJUSTMENTS > REMOTE ENGINE START OF THE APPLIED VEHICLES OWNERS MANUAL. WHEN DIAGNOSING RES OPERATION, USE THE SUPPLEMENTAL RES SERVICE INFORMATION AND SUPPLEMENTAL DIAGNOSIS TABLE (STARTING ON PAGE 2) IN ADDITION TO THE ESM."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"INTELLIGENT KEY BATTERY VOLTAGE CHECK AND REPLACEMENT THIS BULLETIN HAS BEEN SUPERSEDED BY NTB15-077. NISSAN; SIGNAL TECH-II INTELLIGENT KEY BATTERY TEST AND SIGNAL CHECK PLEASE DISCARD PREVIOUS VERSIONS OF THIS BULLETIN."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"NISSAN; SIGNAL TECH-II INTELLIGENT KEY BATTERY TEST AND SIGNAL CHECK THIS BULLETIN HAS BEEN AMENDED. CHANGES HAVE BEEN MADE THROUGHOUT. PLEASE DISCARD PREVIOUS VERSIONS OF THIS BULLETIN. IF YOU CONFIRM THE INTELLIGENT KEY INTERMITTENTLY OR CONTINUOUSLY DOES NOT FUNCTION. ACTION CHECK THE BATTERY CONDITION WITH THE SIGNAL TECH-II I-KEY BATTERY TEST. IMPORTANT: CONFIRM THAT THE SIGNAL TECH-II HAS THE MOST RECENT UPDATE. UPDATE CAN BE PERFORMED THROUGH ASIST / SPECIALTY TOOLS / SIGNAL TECH-II."
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION The Service Procedure (starting on page 2) in this bulletin contains the steps to perform TCM Calibration Data Write Procedures. These procedures are used when a complete CVT is replaced, or a CVT control valve (valve body) is replaced, or a Transmission Control Module (TCM) is replaced. See this bulletin for further detail.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION Temporary tire Flat Spotting is common on New Dealer In-Stock vehicles that have not been occasionally moved. Flat Spotting can occur after the vehicle has been parked (not moved) for a few days, or longer. In most cases it is temporary. In extreme cases it can be permanent. Vehicles should be moved every 30 days, in one direction only, enough to rotate the tires 90° (see Figure 1). Moving vehicles as shown will prevent tire Flat Spotting. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
IMPORTANT: Metal debris and friction material may become trapped in the radiator, cooling hoses, bypass valve or external CVT fluid cooler. This debris can contaminate the newly serviced transmission, control valve or torque converter. In severe cases this debris can block or restrict flow and may cause damage to the newly serviced CVT. SERVICE INFORMATION When a CVT, control valve or torque converter replacement is necessary for one of the applied vehicles, the CVT transmission fluid coolers (radiator based fluid cooler and external auxiliary cooler if present) must be flushed. Please see this bulletin for further details.
Source components: EQUIPMENT · POWER TRAIN · POWER TRAIN:AUTOMATIC TRANSMISSION:INTERNAL:CVT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM: The customer reports a transmission judder (shake, shudder, single or multiple bumps or vibration) AND One of these DTCs is stored: - P17F0 (CVT_JUDDER (T/M INSPECTION)) - P17F1 (CVT_JUDDER (C/U INSPECTION)) NOTE - If a transmission judder (as described above) is not reported, this bulletin does not apply. - If either P17F0 or P17F1 are not stored, this bulletin does not apply. - NTB15-014, Enhanced Diagnostic Logic For CVT Judder, has reprogramming instructions that may apply. ACTIONS: Perform the SERVICE PROCEDURE, starting on page 3. - Review the Repair Flow Chart in this bulletin. NOTE: Essential Tool Tech Cam (borescope) J-51951 has been sent to dealers. This tool?s attachments make CVTinspection possible. See this bulletin for further detail.
Source components: EQUIPMENT ADAPTIVE/MOBILITY · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION Nissan is issuing this Technical Service Bulletin to clarify that a change has been made for the logic that controls the Occupant Classification System (OCS) and 'passenger airbag indicator' (PABI), as described in the Owner?s Manual. This TSB applies only to vehicles using the 2-sensor OCS. Those changes are: * PABI light is ON with an empty front passenger seat. Please see this bulletin for further details.
NHTSA source summary · Original PDF not reviewed by Recallfolio
OCCUPANT CLASSIFICATION SYSTEM LIGHT OPERATION LOGIC CHANGE SERVICE INFORMATION Nissan is issuing this Technical Service Bulletin to clarify that a change has been made for the logic that controls the Occupant Classification System (OCS) and passenger airbag indicator (PABI), as described in the Owners Manual. This TSB applies only to vehicles using the 2-sensor OCS. Those changes are: PABI light is ON with an empty front passenger seat.
Source components: AIR BAGS:SENSOR:OCCUPANT CLASSIFICATION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM A refrigerant leak at a refrigerant pipe/hose joint location. ACTIONS 1. Inspect the metal surfaces of the pipe/hose joint for damage or contamination. NOTE: Do not replace a refrigerant pipe, hose, or other A/C component if an o-ring seal will solve the leak incident, if it should occur. 2. If no damage is found to the joint metal surfaces, replace the O-ring seal. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement "Certification Label" or "VIN Plate / Label" may be needed. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION If the clip for the fuel filler cap tether becomes lost or is detached for any reason, it is no longer necessary to replace the fuel filler cap. The clip or "pin" is now available as a separate service part. NOTE - Do not replace the fuel filler cap if only the pin is needed. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION Occasionally customers may notice water vapor or fog in the headlamps. The information, illustrations, and flow chart in this bulletin are provided to help you in determining if an incident for water/condensation in the headlamps is normal or not. Nissan?s new vehicle limited warranty does not cover physically damaged (cracked or broken) headlamps. All current headlamp assemblies are vented to the atmosphere (not sealed). - This is necessary to allow for expansion and contraction of air from temperature "variations" (warmer or colder) without damage to the headlamp. - Moisture in the air sometimes "travels" into and out of the headlamp assembly through these vents. - Certain environmental conditions may cause moisture to condense. - The fogging/cloudiness should disappear over time when the headlamp is in a dry environment. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM: The hood of an applied vehicle vibrates or flutters while driving. - This issue may be noticed when passing by or being passed by a large truck with trailer on the highway. ACTION: Refer to the FLOW CHART on page 2 of this bulletin. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM The MIL is "ON" with DTC P0603 (ECM BACK UP/CIRCUIT). ACTION 1. Confirm that the battery voltage is 11 volts, or more, with the ignition ON (engine OFF, not running). 2. Erase DTC 3. Perform DTC confirmation steps in the Service Procedure. 4. Confirm 1st trip DTC P0603 is not stored. NOTE: P0603 is often the result of low battery voltage, discharged battery or battery terminal disconnections. Please see this bulletin for furtner details.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION On Applied Vehicles, the torque specification for the rear final drive assembly rear mounting stud has been revised. New torque specification: 71 N-m, 7.2 kg-m, 52 ft-lbs Use the torque specification shown above when installing a rear final drive assembly. At a later date and where possible, the applicable Electronic Service Manuals will be updated with the revised specification. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION The purpose of this bulletin is to give Nissan dealers guidelines to help determine if windshield breakage is covered under warranty or is the customer?s responsibility. Nissan North America (NNA) is not responsible for damage to glass that is a result of objects striking or scratching the glass. However, NNA is responsible for manufacturing issues such as distorted glass and cracks that are due to improper installation or damage to the glass during vehicle assembly. NNA typically does not find any type of cracks in the windshield due to stress after the dealership PDI. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION The function to detect the last item to trigger the vehicles theft alarm system can now be accessed with CONSULT-III plus (C-III plus). This function can be accessed by selecting: * Diagnosis (All Systems) or Diagnosis (One System). Then * BCM Then * THEFT ALM Then * Work Support Then * THEFT ALM TRG. See this bulletin for further details.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION Whenever all Intelligent Keys of an APPLIED VEHICLE are lost AND the BCM is in Transit Mode, the BCM does not need to be replaced when replacing the lost Intelligent Keys. When all of the following conditions of an APPLIED VEHICLE are verified: - The BCM is in Transit Mode. - The BCM will not respond to CONSULT-III plus (C-III plus). It does not show up on System Call. - All Intelligent Keys are lost. DO NOT replace the BCM or ECM when replacing the lost Intelligent Keys. The procedure in this bulletin will get the existing BCM out of Transit Mode. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION When the BCM in an APPLIED VEHICLE is being replaced for any reason, all existing Intelligent Keys must be re-registered. If new Intelligent Keys are added to the existing Intelligent Keys at the same time the BCM is being replaced, the procedure in this bulletin must be followed. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This activity will expire on December 18th, 2015. Dealers can continue to schedule and repair vehicles eligible for this service action until close of business December 18th, 2015. Claims will be honored for RO?s opened on or before the 18th of December.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION The Intelligent Keys used on the various Nissan vehicles may not be interchangeable between models and years. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION The tie down hook is no longer included with the jacking tools on 2016 Pathfinder vehicles, effective with the Applied Date and VIN shown in this bulletin. Do not submit warranty claims for a missing tie down hook (a hook that was not originally supplied with the vehicle). See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Nissan is conducting a dealer inventory service action to inspect and, if necessary, replace the hood latch on certain MY 2015 Murano, MY2016 Maxima, and MY2015-16 Rogue and Pathfinder vehicles
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION Windshield "foreign material" that is on the surface of the glass in some cases can be cleaned off with a very particular type and grade of steel wool. * Most any foreign material on the surface of the Windshield can be cleaned off by using #0000 super fine steel wool. >The #0000 grade super fine steel wool can be found in most hardware stores. Please see this bulletin for further details.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION When replacing both of the vehicle?s I-Keys, due to being lost prior to vehicle delivery, new I-Keys can now be registered without the BCM (or ECM) being replaced. Do not replace the BCM (or ECM) before replacing I-Keys for the Applied Vehicles. Please see this bulletin for further details.