Original record summaries, dates and identifiers for this model-year. Records 201–300 of 393, ordered newest first. Dated records on this page: Dec 13, 2019–Jun 1, 2021.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Jun 1, 2021Service Bulletin/Repair Instructions
MT-003-21
NHTSA communication ID: 10198574
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may experience exterior trim heat damage when parked near a glass building. This may be caused by the suns reflection. If a building creates enough of a curve with a series of flat windows, which act like mirrors, the reflections all converge at one point, focusing and concentrating the light onto the street below.
Source components: VISIBILITY:POWER WINDOW DEVICES AND CONTROLS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may have one of the following DTCs stored in memory along with a system status notice on the Multi-information display OR display a system status notice with no DTC: C1001:92 - Forward sensing camera (FSC) poor field of view [Gen 6 vehicles], B14F0:92 - General temporary failure in forward sensing camera (FSC) [Gen 7 vehicles build on or before March 2, 2019], No DTC - Gen 7 vehicles built after March 2, 2019, DTC C1001:92 or B14F0:92 set as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. In some cases the customer may have a concern with the Lane Departure Warning System (LDWS) and/or High Beam Control system (HBC). In other cases this DTC might be found without a related customer concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When performing vehicle services such as control unit software update, control unit registration/activation, CMU log data retrieval, etc., always use the DCA8000 OR GR8 battery charger SST to maintain battery voltage.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The rear differential case could develop a crack in the case, as shown below. NOTE: This could affect new vehicles just delivered to the dealer as well as customer vehicles.
NHTSA source summary · Original PDF not reviewed by Recallfolio
There have been warranty claims submitted for growling or bearing whine noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When programming a key or installing a Genuine Mazda Accessory Remote Engine Start system, you may encounter programming difficulty. This may be caused by a customer installed aftermarket decorative trim and/or cover on the START/STOP ENGINE button. The aftermarket accessory may create electrical interference, which may interfere with programming.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Auxiliary key blank cutting procedure: There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method, B. Auxiliary Key Code Cut Method
NHTSA source summary · Original PDF not reviewed by Recallfolio
APPLE CARPLAY / ANDRID AURO FREQUENTLY ASKED QUESTIONS (FAQ) The following vehicles are not equipped with Apple CarPlay⢠/ Android Autoâ¢, but it can be activated using MDARS. See Activation instructions on MGSS -> Infotainment -> MAZDA CONNECT Updates -> Apple Carplay / Android Auto MDARS Activation Instructions
NHTSA source summary · Original PDF not reviewed by Recallfolio
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain about rust at the bottom (inner side) of the doors where the seaming welt is located. It is caused by mud/sand adhering to the side sill, which scratches the paint surface when the door is opened/closed. The mud/sand is most likely brought in by the driver and/or passenger when stepping in and out of the vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When performing the MGSS Workshop Manual 360ð View Monitor System Aiming Procedure, M-MDS may show error message "Procedure unsuccessful". This may be caused by light glare on the SST.
NHTSA source summary · Original PDF not reviewed by Recallfolio
MULTI-MODEL - MAZDA MOBILE START CUSTOMER SATISFACTION PROGRAM (CSP05). As shared previously, due to planned industry-wide changes in mobile network infrastructure and wireless technology, the Mazda Mobile Start (MMS) accessory was no longer offered beginning with 20MYvehicles. These technology changes are scheduled to occur in late 2021 as our service provider transitions away from a 3G network which currently supports the MMS application and its vehicle operations for all active legacy accounts. As a result, the MMS application and its vehicle operations will no longer work after September 30. 2021 for these legacy accounts and their respective vehicle owners. In an effort to provide advance notice and be transparent, and also to lessen the inconvenience of this situation - On 11/12/2020, all active MMS account holders will be informed of this news and will be presented with their choice of one of following goodwill offers: A new, replacement remote-engine start system (key fob transmitter type), Installation of Apple CarPlay / Android Auto, A $1000 voucher towards the purchase or lease of a new Mazda vehicle
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
MULTI-MODEL - MAZDA MOBILE START CUSTOMER SATISFACTION PROGRAM (CSP05). As shared previously, due to planned industry-wide changes in mobile network infrastructure and wireless technology, the Mazda Mobile Start (MMS) accessory was no longer offered beginning with 20MYvehicles. These technology changes are scheduled to occur in late 2021 as our service provider transitions away from a 3G network which currently supports the MMS application and its vehicle operations for all active legacy accounts. As a result, the MMS application and its vehicle operations will no longer work after September 30. 2021 for these legacy accounts and their respective vehicle owners. In an effort to provide advance notice and be transparent, and also to lessen the inconvenience of this situation - On 11/12/2020, all active MMS account holders will be informed of this news and will be presented with their choice of one of following goodwill offers: A new, replacement remote-engine start system (key fob transmitter type), Installation of Apple CarPlay / Android Auto, A $1000 voucher towards the purchase or lease of a new Mazda vehicle
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The Mazda DCA-8000PM is required for all warranty battery testing. If the Mazda DCA-8000PM is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code.
NHTSA source summary · Original PDF not reviewed by Recallfolio
A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/C evaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. âÂÂMazda Air Cooling Coil Coatingâ is available to encapsulate the mold to reduce odors. If the product is properly applied, it can effectively reduce the musty/mildew odor for up to three years.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored in memory after engine start and room fuse 15A (A) removed. P2610:00: Instrument cluster internal engine off timer performance problem. P2507:00: PCM battery voltage low input
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain that their seat warmers or seat ventilation do not turn on when the engine is restarted after being left on when turning off the engine. The logic has changed from previous Mazdas where the seat warmers and seat ventilation automatically turned on when the engine was restarted.
NHTSA source summary · Original PDF not reviewed by Recallfolio
MULTI-MODEL - MAZDA MOBILE START CUSTOMER SATISFACTION PROGRAM. As shared previously, due to planned industry-wide changes in mobile network infrastructure and wireless technology, the Mazda Mobile Start (MMS) accessory was no longer offered beginning with 20MYvehicles. These technology changes are scheduled to occur in late 2021 as our service provider transitions away from a 3G network which currently supports the MMS application and its vehicle operations for all active legacy accounts. As a result, the MMS application and its vehicle operations will no longer work after September 30. 2021 for these legacy accounts and their respective vehicle owners. In an effort to provide advance notice and be transparent, and also to lessen the inconvenience of this situation - On 11/12/2020, all active MMS account holders will be informed of this news and will be presented with their choice of one of following goodwill offers: A new, replacement remote-engine start system (key fob transmitter type), Installation of Apple CarPlay / Android Auto, A $1000 voucher towards the purchase or lease of a new Mazda vehicle
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may experience stains appearing on the hood, roof and/or trunk of the vehicle. This concern is most likely to be found in a cold weather areas just after the RAPGARD is removed at PDI. This may be caused by moisture which has been trapped and condensed between the paint and the RAPGARD. These types of stains can be removed with a heat gun or an infrared drier.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When encountering a vehicle with paint damage, refer to the "Mazda Paint Warranty Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN · STEERING · WHEELS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
In order to ensure key code security, MNAO has restricted key code access for the new auxiliary key. This Service Alert provides information on how to obtain the 10-digit key code needed for cutting a new auxiliary key blank if all auxiliary keys are lost.
NHTSA source summary · Original PDF not reviewed by Recallfolio
At PDI or when new vehicle is delivered, some customers may complain about wrinkles on the leather seat cushion and/or seat back surface. Customers having this concern should have their vehicle repaired by a qualified upholstery repair specialist using the following repair procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CRACKED REAR DIFFERENTIAL. The rear differential case could develop a crack in the case, as shown below. NOTE: This could affect new vehicles just delivered to the dealer as well as customer vehicles.
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain about the following MAZDA CONNECT⢠Temperature Warning message: ï· Display is too Hot. Screen performance may be decreased until it cools. The warning message displays when the MAZDA CONNECT⢠screen temperature is above 176 degrees Fahrenheit (80 degrees Celsius).
Source components: ELECTRICAL SYSTEM · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit a Connectivity Master Unit (CMU), a BLUETOOTHî hands-free unit or text messaging related concerns. To improve the handling of BLUETOOTHî hands-free and/or text messaging customer concerns, Mazda created a special service and parts exchange program as of February 2010.
Source components: ELECTRICAL SYSTEM · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
MULTI-MODEL - MAZDA MOBILE START CUSTOMER SATISFACTION PROGRAM. As shared previously, due to planned industry-wide changes in mobile network infrastructure and wireless technology, the Mazda Mobile Start (MMS) accessory was no longer offered beginning with 20MYvehicles. These technology changes are scheduled to occur in late 2021 as our service provider transitions away from a 3G network which currently supports the MMS application and its vehicle operations for all active legacy accounts. As a result, the MMS application and its vehicle operations will no longer work after September 30. 2021 for these legacy accounts and their respective vehicle owners. In an effort to provide advance notice and be transparent, and also to lessen the inconvenience of this situation - On 11/12/2020, all active MMS account holders will be informed of this news and will be presented with their choice of one of following goodwill offers: A new, replacement remote-engine start system (key fob transmitter type), Installation of Apple CarPlay⢠/ Android Autoâ¢, A $1000 voucher towards the purchase or lease of a new Mazda vehicle
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain about high engine oil consumption. Before attempting any repairs, verify the complaint by using the guideline below to determine if an engine repair is necessary: Engine Oil Consumption Inspection Guideline 1. Record the vehicle mileage. 2. Engine at normal operating temperature, top off engine oil level to the full mark on the dipstick. 3. Ask the customer to return to the dealer after 1200 miles to recheck the engine oil level. 4. After 1200 miles, engine at normal operating temperature, check the engine oil level on the dipstick. 5. Is the engine oil level above the low mark on the dipstick? ïÃÂ÷ Yes - No repair is necessary. ïÃÂ÷ No - Proceed to MGSS online or Workshop Manual (section 01-03 NO. 16 HIGH OIL CONSUMPTION/LEAKAGE).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles equipped with electric parking brake (EPB) may exhibit a grinding noise from the rear brakes when braking. This may be caused by the rear brake pads not having the capability to remove the rust from the rear brake discs. The red rust accumulated on the discs is exposed to high temperatures during braking, and consequently the rust turns black. As the black rust is too hard to be removed by the brake pads, the rust progress is accelerated, resulting in the grinding noise.
Source components: EQUIPMENT · PARKING BRAKE:ELECTRICAL · SERVICE BRAKES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Currently, the instructions on MGSS recommend the use of Loctite 962T or equivalent when installing a SKYACTIV cylinder head, but it is no longer available. The following 3 adhesives are alternatives available as an equivalent to Loctite 962T: Loctite 272, Loctite 518 Threebond TB-1386H
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
APPLE CARPLAY / ANDROID AUTO FREQUENTLY ASKED QUESTIONS (FAQ): NOTE: The following vehicles are not equipped with Apple CarPlay / Android Auto, but it can be activated using MDARS. See Activation instructions on MGSS - Infotainment - MAZDA CONNECT Updates - Apple Carplay / Android Auto MDARS Activation Instructions
NHTSA source summary · Original PDF not reviewed by Recallfolio
CRACKED REAR DIFFERENTIAL: Be aware that some new AWD vehicles have been found with cracked rear differential cases, as shown below. NOTE: This may affect new vehicles just delivered to the dealer or new vehicles in dealer inventory.
Source components: ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM) · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles equipped with electric parking brake (EPB) may exhibit a grinding noise from the rear brakes when braking. This may be caused by the rear brake pads not having the capability to remove the rust from the rear brake discs. The red rust accumulated on the discs is exposed to high temperatures during braking, and consequently the rust turns black. As the black rust is too hard to be removed by the brake pads, the rust progress is accelerated, resulting in the grinding noise. To eliminate this concern, the brake pad material has been changed in order to improve the rust-removing capability.
Source components: PARKING BRAKE:ELECTRICAL · SERVICE BRAKES, AIR:DISC:PADS · SERVICE BRAKES, HYDRAULIC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit that the SBS/SCBS warning light (amber) turns ON right after the engine is started with DTC U0420:68 [FSC] (Error signal received from electric power steering (EPS) control module) stored in memory. For Mazda6 and CX-5, the following error messages may appear in the instrument cluster. ï· Front camera sensor system malfunction ï· Forward Smart City Brake Support Malfunction ï· Driver attention alert system malfunction. This may be caused by the battery voltage falling and the EPS control module failing the initial learning for the steering center position while cranking. The FSC detects the error notified by the EPS control module. To correct this concern, the control software of the EPS control module has been modified while the repair procedure modifies the FSC for earlier repairs in the market.
Source components: ELECTRICAL SYSTEM · EQUIPMENT ADAPTIVE/MOBILITY · FORWARD COLLISION AVOIDANCE · SERVICE BRAKES · STEERING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 70.00.367 or later). NOTE: For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will be removed from the Active Driving Display as part of MazdaâÂÂs continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the software. If the customer agrees, turn off the tachometer display on the AD-Display tab in MAZDA CONNECT Settings before performing the update.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain of a steering wheel vibration (in a rotational direction), when they are not holding onto the steering wheel. The vibration stops when holding onto the steering wheel or when driving. This may be caused by improper control logic of the EPS control module. To eliminate this concern, the EPS control logic has been modified.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit that the SBS/SCBS warning light (amber) turns ON right after the engine is started with DTC U0420:68 [FSC] stored in memory. ï· DTC U0420:68 [Forward sensing camera (FSC)]: Error signal received from electric power steering (EPS) control module. For Mazda6 and CX-5, the following error messages may appear in the instrument cluster. ï· Front camera sensor system malfunction ï· Forward Smart City Brake Support Malfunction ï· Driver attention alert system malfunction. This may be caused by the battery voltage falling and the EPS control module failing the initial learning for the steering center position while cranking. The FSC detects the error notified by the EPS control module. To correct this concern, the control software of the EPS control module has been modified while the repair procedure modifies the FSC for earlier repairs in the market.
Source components: ELECTRICAL SYSTEM:12V/24V/48V BATTERY · EQUIPMENT ADAPTIVE/MOBILITY · SERVICE BRAKES, HYDRAULIC · STEERING:ELECTRIC POWER ASSIST SYSTEM · VISIBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit poor fitting rear door weatherstrips at the lower/front location. The weatherstrips may be deformed by frequent contact with passengers entering and exiting the vehicle, causing the weatherstrip joint to become enlarged. The enlarged weatherstrip joint does not grip the door panel tight enough when it is refitted.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Mazda Accessories has re-released the Front and Rear Bumper Trim kits for the CX-9 (see the table below for application and required components). NOTE: The Front and Rear Bumper Trim Kits are only to be installed on Sport and Touring Models from 2020MY and forward. The Rear Bumper Trim contained within the kit is not compatible with the Handsfree Liftgate Sensor that comes standard on the Carbon Edition (new for 2021), GT, or the Signature Models.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain of a steering wheel vibration (in a rotational direction), when they are not holding onto the steering wheel. The vibration stops when holding onto the steering wheel or when driving. This may be caused by improper control logic of the EPS control module. To eliminate this concern, the EPS control logic has been modified.
NHTSA source summary · Original PDF not reviewed by Recallfolio
A new cylinder head assembly for service parts has been newly established for SKYACTIV-G 2.5 with cylinder deactivation when replacement is needed. Valves, valve springs, valve spring seats, and cotters (IN/EX) are included in the new assembly. NOTE: Cylinder head replacement requires MASH authorization.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When performing vehicle services such as control unit software update, control unit registration/activation, CMU log data retrieval, etc., always use the GR8 battery charger SST to maintain battery voltage.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain about the following message displayed in the Multi-Information Display: In the following cases, the MRCC with Stop & Go function system is canceled when the vehicle is traveling at 19 mph (30 km/h) or less: ï· The Forward Sensing Camera (FSC) cannot detect target objects due to one of the following: ï· The windshield is dirty ï· The FSC lens is foggy ï· There is low visibility due to rain, fog or snow ï· It is at night and there is not enough light ï· There is direct or reflected sunlight on the FSC ï· There is problem with the FSC ï· There is a problem with the AUTOHOLD control function. ï· There is a problem with the electric parking brake (EPB).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain about an inoperative power liftgate (PLG) and the any of the following DTC's stored in memory: ï· U3003:16 (Power liftgate (PLG) control module power supply voltage low input) ï· U3003:17 (Power liftgate (PLG) control module power supply voltage high input). This may be caused by low or high vehicle battery voltage.
NHTSA source summary · Original PDF not reviewed by Recallfolio
New CARB regulation regarding mandatory checking and documenting of tire pressure whenever a vehicle is in for service work. This applies to all service shops (including Mazda dealerships) in California effective September 1, 2010.
Source components: TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS · WHEELS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may experience an engine no start due to low battery voltage. Mazda is aware of the issue and is working on a solution. NOTE: Battery parasitic draw is intermittent. When the condition is present, battery parasitic draw exceeds 65 mA (0.065 A) 40 minutes after key OFF.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain of a steering wheel vibration (in a rotational direction), when they are not holding onto the steering wheel. The vibration stops when holding onto the steering wheel or when driving. This may be caused by improper control logic of the EPS control module. To eliminate this concern, the EPS control logic has been modified.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When encountering a vehicle with paint damage, refer to the "Mazda Paint Warranty Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable).
NHTSA source summary · Original PDF not reviewed by Recallfolio
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed. Below are a couple of examples of unusual electrical concerns caused by aftermarket devices.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). This is caused by the oil pressure switch A and/or B at the control valve body temporarily or permanently getting stuck due to contamination entering the passage. To correct the problem, some mass production changes have been implemented to reduce contamination and improve the DTC diagnostic logic.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may notice cracks (as shown below) at one or both ends of the front bumper near the front fender / front combination light. This may be caused when driving over bumps. The bumper fascia may receive higher than expected forces, depending on driving manner and road conditions. To eliminate this concern, the internal shape and material of the front bumper fascia has been modified.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When replacing manual or automatic transmission, make sure to remove the plug from the old transmission (as shown below) and then re-install it to the new transmission with a new washer. The new transmissions (including remanufactured A/T) have a shipping plug, as shown in the figures (M/T: black, rubber made; A/T: pink and black, with breather). This plug is for shipping use only and needs to be removed in order to re-install the original plug from the old transmission.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain that the rear console / cup holder area is warming. The warming is caused by heat radiating from the rear heater core, which is located under the console. The warm air created by the heater core escapes through small gaps and carries heat along the inner walls of rear console / cup holder, causing an increase in temperature.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may experience an engine no start due to low battery voltage. Mazda is aware of the issue and is working on a solution. NOTE: Battery parasitic draw is intermittent. When the condition is present, battery parasitic draw exceeds 65 mA (0.065 A) 40 minutes after key OFF. Contact Hotline for latest repair information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Be aware that some new AWD vehicles have been found with cracked rear differential cases, as shown below. NOTE: This may affect new vehicles just delivered to the dealer or new vehicles in dealer inventory.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit a click or squeak noise from the front brakes under the following conditions: Click Noise: 1. When first moving forward or reverse from a stop OR 2. When first applying the brakes while moving forward at slow speeds. Squeak Noise: During light braking.
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · SERVICE BRAKES, HYDRAULIC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · POWER TRAIN · SERVICE BRAKES, HYDRAULIC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit a click noise from the front brakes under one of the following conditions: ï· When first moving the vehicle forward or reverse from a stop. ï· When first applying the brakes while the vehicle is moving forward at slow speeds. Due to deteriorated grease between the brake pads and the shim, the front brake pads move upward/downward along with the brake rotors during brake application. When the vehicle moves or the brakes are applied the next time, the front brake pads move to the other side, which causes a click noise.
Source components: EQUIPMENT ADAPTIVE/MOBILITY · SERVICE BRAKES, HYDRAULIC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The ownerâÂÂs manual contains procedures and precautions for the maintenance and cleaning of plastic parts, like the brand emblem. However, it is still important to remind customers about these precautions. Customers should never use inadequate, harsh or aggressive cleaning products on plastic parts. CAUTION: Be aware that when cleaning the brand emblem, never use cleaning products that are highly acidic/alkaline detergent, organic solvents or those with aggressive chemical products, otherwise, the brand emblem may become cracked and/or deformed (as shown in the example below). Always refer customers to the ownerâÂÂs manual for proper cleaning using cold or lukewarm water and a mild, neutral detergent.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may have one of the following DTCs stored in memory: ï· C1001:92 - Forward sensing camera (FSC) poor field of view ï· B14F0:92 - General temporary failure in forward sensing camera (FSC) DTC C1001:92 or B14F0:92 set as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. ï· In some cases the customer may have a concern with the Lane Departure Warning System (LDWS) and/or High Beam Control system (HBC). ï· In other cases this DTC might be found without a related customer concern. NOTE: Instrument Cluster Multi-Information Display Warning Messages vary depending on vehicle year/model. See the Owner's Manual for details.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SiriusXM Traffic Plus and Travel Link are displayed with Mazda in-vehicle factory navigation systems. Both of these services provide information in the U.S. & Canada. NOTE: SiriusXM Traffic Plus and Travel Link subscription is free of charge for 3 years only if equipped with factory installed navigation system. NOTE: 2019-2020 Mazda3 and 2020 CX-30 are not equipped with factory installed navigation system,however, it is available as a dealer installed accessory. SiriusXM Traffic Plus and Travel Link are available on the 2019-2020 Mazda3 and 2020 CX-30 Preferred Package and above, as a paid subscription. Traffic Plus feature requires in-vehicle navigation SD card. SiriusXM Satellite Radio trial subscription is free of charge for 3 months.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Service part Automatic Transaxles (ATX) manufactured on or after July, 2018 are shipped with a blank TCM that requires configuration. NOTE: The following Caution is included with every ATX that requires configuration.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit a click noise from the front brakes under one of the following conditions: When first moving the vehicle forward or reverse from a stop. When first applying the brakes while the vehicle is moving forward at slow speeds. Due to deteriorated grease between the brake pads and the shim, the front brake pads move upward/downward along with the brake rotors during brake application. When the vehicle moves or the brakes are applied the next time, the front brake pads move to the other side, which causes a click noise.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit grooves (1) in rear brake disc plate(s), as shown below. This concern is mostly found on new or low mileage vehicles, when the brakes are new. The grooves may be caused through abrasion from the accumulation of metal particles from the rear brake disc plates. The metal particles get caught between the brake pads and disc plates causing groove damage. To eliminate this concern, the disc plate surface honing process has been changed to reduce metal particle formation.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit power outer mirror(s) that do not fold in and/or out when using the outer mirror switch. This concern may be caused by insufficient water tightness, allowing water to enter the electric folding unit resulting in corrosion damage. To eliminate this concern, the overlapping area (1) of the water-proof seal (inside electric fold-in unit) has been extended.
NHTSA source summary · Original PDF not reviewed by Recallfolio
If you encounter sputtering, surging or poor driveability with the following DTCs stored, inspect the MAP sensor connection for corroded terminals (as shown below). Recommend replacing the engine wire harness and MAP sensor. Refer to GEPC for applicable part numbers.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Due to a vehicle side logic change for the vehicles listed above, the seat warming and seat ventilation systems will no longer automatically turn on when the vehicle is started using the MMS accessory. Both features will now require a manual setting every time the vehicles are restarted after being turned off. Refer to the vehicle ownerâÂÂs manual for more details on proper seat warmer/seat ventilation operation.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain that their seat warmers or seat ventilation do not turn on when the engine is restarted after being left on when turning off the engine. The logic has changed from previous Mazdas where the seat warmers and seat ventilation automatically turned on when the engine was restarted. NOTE: Customers in cold weather are more likely to complain about this if their vehicle is equipped with Mazda Mobile Start (MMS) (not available on Mazda3 or CX-30) because the MMS accessory instructions state the seat warmers WILL turn on when the engine is restarted. The same can happen in the hotter weather with the seat ventilation. This information is incorrect for these vehicles. Both features will now require a manual setting every time the vehicles are restarted after being turned off. Consult the vehicleâÂÂs ownerâÂÂs manual for more details on proper seat warmer/seat ventilation operation.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain that the steering wheel is off center more than 3ð even when driving straight on a flat road. Customers having this concern should have their vehicle repaired using the following repair procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored in memory after engine start and room fuse 15A (A) removed.ï· P2610:00: Instrument cluster internal engine off timer performance problem ï· P2507:00: PCM battery voltage low input. As a past malfunction, the customer will not notice it (no warning light illuminated), but the DTC may be found during a vehicle service. P2507 in this situation is only applicable on 2016 and later models. This is caused by the engine being started 3 or more times after a short duration of engine off (less than 15 seconds) with the room fused removed. NOTE: The odometer will display âÂÂF0-002â during transport mode (room fuse 15A removed). Transport mode is canceled when room fuse 15A is installed or the vehicle odometer is more than 12.4mi (20km).Vehicles in dealer inventory with this concern should be repaired using the following repair procedure.
Source components: ELECTRICAL SYSTEM · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
LACK OF POWER UNDER HEAVY LOAD WITH NO WARNING LIGHTS OR DTCS: Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · STRUCTURE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may experience stains appearing on the hood, roof and/or trunk of the vehicle. This concern is most likely to be found in a cold weather areas just after the RAPGARD is removed at PDI. This may be caused by moisture which has been trapped and condensed between the paint and the RAPGARD. These types of stains can be removed with a heat gun or an infrared drier. If you encounter this concern during PDI, use a heat gun or an infrared drier to apply heat to the affected area to remove the stain(s).
NHTSA source summary · Original PDF not reviewed by Recallfolio
At PDI or when new vehicle is delivered, some customers may complain about wrinkles on the leather seat cushion and/or seat back surface. Customers having this concern should have their vehicle repaired by a qualified upholstery repair specialist using the following repair procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When encountering a vehicle with paint damage, refer to the "Mazda Pocket Paint Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable). Copies of the Mazda Pocket Paint Guide are available for order on Mazda e-Store (part number: 9999-95-MPPG-12).
NHTSA source summary · Original PDF not reviewed by Recallfolio
In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealerâÂÂs responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. ï· Mazda vehicles are manufactured with tamper-proof speedometers. ï· When a speedometer is replaced, the new speedometer will read zero (0) miles. ï· This procedure is extremely important to accurately represent actual vehicle mileage. ï· Prior to speedometer removal, complete the information required on the âÂÂSpeedometer Replacement LabelâÂÂ. Labels can only be ordered through Mazda eStore. ï· In an effort to achieve a higher level of Customer Experience and retain the value of MazdaâÂÂs vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMOâÂÂs services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Follow the inspection guidelines below to determine if the condition is a result of the normal sweeping process or a failure of the shaft seal.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit one or more of the following noises from the front suspension: 1. A creaking noise from under the front of the vehicle (front lower arm bushing) when driving over bumps at approximate 12 - 25 mph (20 - 40 Km/h). The noise occurs when the road surface is wet or after the vehicle has been washed. The noise becomes more noticeable as the bumps get higher. The creaking noise is caused by the front lower arm bushing (A) making a stick-slip noise during wet road conditions. 2. A clunking noise from the front coil spring when driving over bumps. The clunking noise is due to stickslip between the front strut bearing (B) and the coil spring (C). 3. A popping noise from the bump stopper (D) when driving through gutters.To eliminate the noise, the following mass-production changes have been made: 1. The coating treatment of the lower arm bushing has been changed to reduce friction and prevent stick-slip. 2. Protectors have been installed onto the coil springs to prevent stick-slip. 3. The bump stopper has been modified and grease application has been added to prevent the stick-slip.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit corrosion of the wheel nuts. This is caused by torsional stress concentrating on the tip of the wheel nut because of the thin and long shape of the nut, which damages the coating and causes the corrosion. To correct this issue, the width across the flats of the wheel nuts have been changed from 17mm to 21mm.
NHTSA source summary · Original PDF not reviewed by Recallfolio
All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 70.00.352 or later).
NHTSA source summary · Original PDF not reviewed by Recallfolio
If an engine assembly is replaced after a catastrophic internal mechanical failure, clean the intake manifold internally before installing a replacement engine assembly. If the intake manifold is not cleaned properly, the replacement engine may fail prematurely. Metallic debris from the old engine (with catastrophic internal mechanical failure) may rest inside the intake manifold. When the new engine assembly is installed, debris in the intake manifold will be ingested into the new engine and cause internal damage.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
WARRANTY GUIDELINES FOR RETURNED TRANSMISSION CORES. Be advised that the Mazda Remanufactured Transmission Center (MRTC) has found that up to 30% of the returned transmission cores either included the wrong transmission oil cooler, or the oil cooler was missing altogether. IMPORTANT NOTE: ALWAYS REMEMBER TO INCLUDE THE ORIGINAL OIL COOLER WITH THE RETURNED TRANSMISSION CORE!
Source components: POWER TRAIN · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/C evaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. âÂÂMazda Air Cooling Coil Coatingâ is available to encapsulate the mold to reduce odors. If the product is properly applied, it can effectively reduce the musty/mildew odor for up to three years. NOTE: See parts information for Mazda Air Cooling Coil Coating and Kit part numbers.