Original record summaries, dates and identifiers for this model-year. Records 201–275 of 275, ordered newest first. Dated records on this page: May 3, 2013–Dec 14, 2015.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Dec 14, 2015Service Bulletin/Repair Instructions
01-010-15-3040A
NHTSA communication ID: 10105649
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT AN UNUSUAL NOISE WHILE DRIVING THE VEHICLE. THE NOISE MAY BE CAUSED BY A BROKEN FUEL TANK (B) INSULATOR (A) THAT IS HANGING DOWN AND CONTACTING THE PROPELLER SHAFT. THE RIVETS (C) MAY BREAK WHEN A LOAD OCCURS. THE RIVET MATERIAL HAS BEEN CHANGED TO ELIMINATE THIS CONCERN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT AN UNUSUAL RATTLE/BUZZING TYPE NOISE FROM THE PRESILENCER WHEN DRIVING AT APPROXIMATELY 1800 RPM. THE LOWER (REAR-SIDE) OF THE PRE-SILENCER MAY BE THERMALLY DEFORMED DUE TO INSUFFICIENT RIGIDITY (FEWER WELD SPOTS). THE DEFORMED PORTION MAY RESONATE EXHAUST GAS PULSATIONS, WHICH CAUSES NOISE. A REINFORCED PLATE HAS BEEN ADDED TO THE PRE-SILENCER TO INCREASE THE RIGIDITY, THEREBY ELIMINATING DEFORMATION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE VIBRATION DURING ACCELERATION AND/OR NOISE COMING FROM THE REAR OF THE VEHICLE. DUE TO ENVIRONMENTAL HEAT AND HEAT FROM THE EXHAUST SYSTEM, THE REAR DIFFERENTIAL MOUNTING RUBBER MAY BECOME HARDENED AND CRACKED, RESULTING IN VIBRATION AND/OR NOISE. TO ELIMINATE THIS CONCERN, THE RUBBER MATERIAL HAS BEEN IMPROVED.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMPLAIN THAT THE DOORS DO NOT LOCK / UNLOCK WHEN PRESSING THE REQUEST SWITCH. THIS MAY BE CAUSED BY A TORN OR CRACKED REQUEST SWITCH RUBBER BUTTON (A). THE RUBBER SURFACE OF THE REQUEST SWITCH MAY BECOME GRADUALLY WORN OUT BY REPEATED USE. WATER MAY ENTER THE REQUEST SWITCH AND CAUSE A SHORT-CIRCUIT OF THE ELECTRICAL SYSTEM. TO ELIMINATE THIS CONCERN, THE THICKNESS OF THE RUBBER BUTTON HAS BEEN INCREASED FROM 0.6 MM TO 1.8 MM TO IMPROVE WEAR RESISTANCE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMPLAIN ABOUT ONE OR MORE OF THE FOLLOWING CONCERNS. 1. SMS/TEXT CANNOT BE DOWNLOADED WHEN ONNECTED VIA BLUETOOTH. 2. OPERATIONAL CONCERNS WHEN PLAYING A MEDIA DEVICE (IPOD, USB STICK ETC.) CONNECTED VIA THE USB PORT. A. AFTER THE IGNITION IS TURNED ON, IT TAKES A LONG TIME TO LOAD ALL THE DATA FROM THE DEVICE BEFORE STARTING PLAYBACK. DEPENDING ON THE DATA VOLUME, IT CAN TAKE UP TO SEVERAL MINUTES. B. AFTER THE IGNITION IS TURNED ON, THE PLAYBACK ALWAYS STARTS FROM THE FIRST TRACK. IT DOES NOT START FROM THE LAST PLAYING TRACK/POSITION WHEN THE IGNITION WAS TURNED OFF. C. IPOD ERROR MESSAGE FOR THE APPLE® IOS 8.0 OR HIGHER SOFTWARE ON IPHONE 4, 5, OR 6. THESE CONCERNS MAY BE CAUSED BY THE SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE THAT CONTROLS THE USB CONNECTION. TO IMPROVE THESE CONCERNS, THE SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE HAS BEEN CHANGED. NOTE: THE UPDATED SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE WILL ONLY ADDRESS SMS/TEXT CONCERNS FOR THE APPLE® IPHONE AT THIS TIME.
NHTSA source summary · Original PDF not reviewed by Recallfolio
MAZDA INFOTAINMENT SYSTEMS REQUIRE CONTACTING THE PROPER SOURCE FOR DIAGNOSTIC SUPPORT, PARTS AUTHORIZATION, AND PARTS EXCHANGE. SOME COMPONENTS REQUIRE PRIOR AUTHORIZATION BEFORE ORDERING AS EXCHANGE. REFER TO DAG EXCHANGE CENTRAL (MXCONNECT>PARTS AND ACCESSORIES>PARTS>PROGRAMS>EXCHANGE CENTRAL) FOR COMPONENT AVAILABILITY, SOURCE OF TECHNICAL SUPPORT AND PRIOR AUTHORIZATION REQUIREMENT. NOTE: ALWAYS CHECK FOR A TSB THAT MAY MODIFY OR ELIMINATE PRIOR AUTHORIZATION FOR A SPECIFIC SYMPTOM FOR A GIVEN COMPONENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THE NAVIGATION SYSTEM SUPPORT FOR DIAGNOSTICS, PARTS AUTHORIZATION, AND PARTS EXCHANGE REQUIRE CONTACTING THE PROPER SOURCE. TOMTOM NAVIGATION HELP DESK AT 866-486-6866 FROM 7AM-11PM (M-F) AND 9AM-8PM (SAT) EASTERN STANDARD TIME. NOTE: ONE OF THE FIRST STEPS FOR TROUBLESHOOTING THE NAVIGATION SYSTEM IS FOR THE CUSTOMER OR DEALER TO CALL TOMTOM. IF THE TOMTOM CALL CENTER CANNOT SOLVE THE CUSTOMERS PROBLEM, THEY WILL PROVIDE A CASE NUMBER TO THE CUSTOMER THAT CAN BE REFERRED TO IF NEEDED. SERVICE ADVISORS SHOULD GET THIS CASE NUMBER FROM THE CUSTOMER IF THE VEHICLE COMES INTO THE DEALER FOR FURTHER DIAGNOSIS SO THE TECHNICIAN CAN HAVE IT WHEN CALLING TOMTOM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT BRAKE FLUID SEEPAGE FROM THE BRAKE MASTER CYLINDER RESERVE TANK CAP. THE UPPER SURFACE OF THE RESERVE TANK MAY APPEAR DUSTY OR DIRTY WHERE THE BRAKE FLUID SEEPAGE HAS OCCURRED. THIS CONCERN MAY BE CAUSED BY A DECREASE IN SEALING PERFORMANCE OF CAP DUE TO AGING DETERIORATION. A NEW CAP WITH IMPROVED SEALING PERFORMANCE HAS BEEN ESTABLISHED AS A SERVICE PART
Source components: SERVICE BRAKES, HYDRAULIC:FLUID.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT EITHER AN AUDIO SCREEN THAT IS LOCKING-UP (BLACK SCREEN) OR AN INOPERATIVE AUDIO TOUCH SCREEN. IN BOTH CASES HOWEVER, THE AUDIO UNIT SOUND OUTPUT IS NORMAL. THIS CONCERN MAY BE CAUSED BY AN INTERNAL FAILURE OF THE AUDIO UNIT. THE PRODUCTION PROCESS AT THE AUDIO SUPPLIER HAS BEEN IMPROVED TO ELIMINATE THESE CONCERNS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY EXPERIENCE INOPERATIVE FRONT DOOR WINDOW AUTO-CLOSING OPERATION WHEN USING THE WINDOW SWITCHES (A). THE WINDOW MOVES UPWARD, BUT AUTOMATICALLY RETURNS TO THE HALFWAY POSITION (AS IF THE JAM-SAFE WINDOW FUNCTION IS OPERATING). THE GLASS RUN CHANNEL MAY BE DEFORMED CAUSING INCREASED SLIDING RESISTANCE AGAINST THE WINDOW GLASS. THIS MAY CAUSE THE SYSTEM TO MIS-JUDGE THAT SOMETHING IS BLOCKING THE WINDOW CLOSE MOVEMENT AND OPERATES THE JAM-SAFE WINDOW FUNCTION.
Source components: VISIBILITY:POWER WINDOW DEVICES AND CONTROLS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT AN UNUSUAL NOISE WHILE DRIVING THE VEHICLE. THE NOISE MAY BE CAUSED BY A BROKEN FUEL TANK (B) INSULATOR (A) THAT IS HANGING DOWN AND CONTACTING THE PROPELLER SHAFT. THE RIVETS (C) MAY BREAK WHEN A LOAD OCCURS. THE RIVET MATERIAL HAS BEEN CHANGED TO ELIMINATE THIS CONCERN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY NOTICE THE POWER WINDOW(S) ARE EITHER NOISY OR COMPLETELY INOPERATIVE WHILE OPERATING THE POWER WINDOW SWITCH. THIS MAY BE DUE TO THE POWER WINDOW MOTOR GEAR HAVING CHIPPED OR DAMAGED TEETH. TO ELIMINATE THIS CONCERN, THE POWER WINDOW MOTOR HAS BEEN IMPROVED BY REDUCING THE FORCE APPLIED TO THE GEAR WHEN THE WINDOW IS CLOSED.
Source components: VISIBILITY:POWER WINDOW DEVICES AND CONTROLS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT THE CHECK ENGINE LIGHT ON WITH DTC P0456 STORED IN THE PCM MEMORY. P0456: EVAP SYSTEM LEAK DETECTED (VERY SMALL LEAK) THE CONCERN IS MOST LIKELY THE RESULT OF THE CUSTOMER NOT GETTING THE FUEL CAP COMPLETELY CLOSED AFTER FUELING THE VEHICLE. THIS CAUSES A SMALL FUEL VAPOR LEAK AND TURNS DTC P0456 ON.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Mazda Motor Corporation has decided to conduct a Special Service Program (SSP) on certain 2014 CX-9 and 2015 MX-5 vehicles. On the affected vehicles, the strength of an internal part of the liftgate latch actuator or trunk lid latch actuator may be insufficient due to the usage of inappropriate material. With repeated lock-unlock operation, the internal part may be broken, making the lock-unlock operation impossible.In the worst case, though the trunk lid can be opened using the key, the liftgate or trunk lid may not be opened electrically (by operating switch, transmitter, etc.). Dealers are to replace the liftgate or trunk lid latch with a new, improved latch. This repair must be performed at no charge to the vehicle owner. SSP97 will be in effect until May 31, 2022, regardless of mileage.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE MIL ILLUMINATION WITH DTC P219A:00 AND/OR P219B:00 STORED IN PCM MEMORY. THE DTCS MAY BE CAUSED BY ABNORMAL ELECTRICAL NOISE WITHIN THE ENGINE HARNESS OF CERTAIN VEHICLES. TO ELIMINATE THIS CONCERN, SEPARATE THE A/F SENSOR SIGNAL LINES FROM THE EMISSION HARNESS BY INSTALLING THE SHORT CORD SERVICE PART DETAILED IN THIS BULLETIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMPLAIN ABOUT ONE OR MORE OF THE FOLLOWING CONCERNS. 1. SMS/TEXT CANNOT BE DOWNLOADED WHEN CONNECTED VIA BLUETOOTH. 2. OPERATIONAL CONCERNS WHEN PLAYING A MEDIA DEVICE (IPOD, USB STICK ETC.) CONNECTED VIA THE USB PORT. A. AFTER THE IGNITION IS TURNED ON, IT TAKES A LONG TIME TO LOAD ALL THE DATA FROM THE DEVICE EFORE STARTING PLAYBACK. DEPENDING ON THE DATA VOLUME, IT CAN TAKE UP TO SEVERAL MINUTES. B. AFTER THE IGNITION IS TURNED ON, THE PLAYBACK ALWAYS STARTS FROM THE FIRST TRACK. IT DOES NOT START FROM THE LAST PLAYING TRACK/POSITION WHEN THE IGNITION WAS TURNED OFF. C. IPOD ERROR MESSAGE FOR THE APPLE® IOS 8.0 OR HIGHER SOFTWARE ON IPHONE 4, 5, OR 6. THESE CONCERNS MAY BE CAUSED BY THE SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE THAT CONTROLS THE USB CONNECTION. TO IMPROVE THESE CONCERNS, THE SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE HAS BEEN CHANGED. NOTE: THE UPDATED SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE WILL ONLY ADDRESS SMS/TEXT CONCERNS FOR THE APPLE® IPHONE AT THIS TIME.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMPLAIN ABOUT ONE OR MORE OF THE FOLLOWING CONCERNS. 1. SMS/TEXT CANNOT BE DOWNLOADED WHEN CONNECTED VIA BLUETOOTH. 2. OPERATIONAL CONCERNS WHEN PLAYING A MEDIA DEVICE (IPOD, USB STICK ETC.) CONNECTED VIA THE USB PORT. A. AFTER THE IGNITION IS TURNED ON, IT TAKES A LONG TIME TO LOAD ALL THE DATA FROM THE DEVICE BEFORE STARTING PLAYBACK. DEPENDING ON THE DATA VOLUME, IT CAN TAKE UP TO SEVERAL MINUTES. B. AFTER THE IGNITION IS TURNED ON, THE PLAYBACK ALWAYS STARTS FROM THE FIRST TRACK. IT DOES NOT START FROM THE LAST PLAYING TRACK/POSITION WHEN THE IGNITION WAS TURNED OFF. THESE CONCERN MAY BE CAUSED BY THE SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE THAT CONTROLS THE USB CONNECTION. TO IMPROVE THESE CONCERNS, THE SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE HAS BEEN CHANGED. NOTE: THE UPDATED SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE WILL ONLY ADDRESS SMS/TEXT CONCERNS FOR THE APPLE® IPHONE AT THIS TIME. THE UPDATED SOFTWARE OF THE BLUETOOTH/HANDSFREE MODULE WILL NOT ADDRESS THE IPOD ERROR MESSAGE CONCERN FOR THE APPLE® IOS 8.0 OR HIGHER SOFTWARE ON IPHONE 4, 5, OR 6 AT THIS TIME.
NHTSA source summary · Original PDF not reviewed by Recallfolio
USE THE FOLLOWING REPAIR PROCEDURE TO MINIMIZE THE NEED TO REPLACE THE CATALYST CONVERTER/EXHAUST PIPE WHEN REMOVING OXYGEN SENSORS AND/OR AIR FUEL RATIO SENSORS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE STAINS APPEARING ON THE HOOD, ROOF AND/OR TRUNK OF THE VEHICLE. THIS CONCERN IS MOST LIKELY TO BE FOUND IN A COLD WEATHER AREAS JUST AFTER THE RAPGARD IS REMOVED AT PDI. THIS MAY BE CAUSED BY MOISTURE WHICH HAS BEEN TRAPPED AND CONDENSED BETWEEN THE PAINT AND THE RAPGARD. THESE TYPES OF STAINS CAN BE REMOVED WITH A HEAT GUN OR AN INFRARED DRIER. IF YOU ENCOUNTER THIS CONCERN DURING PDI, USE A HEAT GUN OR AN INFRARED DRIER TO APPLY HEAT TO THE AFFECTED AREA TO REMOVE THE STAIN(S).
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF REPLACEMENT OF THE RIGHT SIDE (RH) TRANSFER OIL SEAL (A), AND TRANSFER DUST SEAL (B) ARE NECESSARY, USE THE FOLLOWING REPAIR PROCEDURE TO INSTALL THE NEW OIL SEALS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMPLAIN ABOUT ONE OR MORE OF THE FOLLOWING CONCERNS. 1. SMS/TEXT CANNOT BE DOWNLOADED WHEN CONNECTED VIA BLUETOOTH. 2. OPERATIONAL CONCERNS WHEN PLAYING A MEDIA DEVICE (IPOD, USB STICK ETC.) CONNECTED VIA THE USB PORT. A. AFTER THE IGNITION IS TURNED ON, IT TAKES A LONG TIME TO LOAD ALL THE DATA FROM THE DEVICE BEFORE STARTING PLAYBACK. DEPENDING ON THE DATA VOLUME, IT CAN TAKE UP TO SEVERAL MINUTES. B. AFTER THE IGNITION IS TURNED ON, THE PLAYBACK ALWAYS STARTS FROM THE FIRST TRACK. IT DOES NOT START FROM THE LAST PLAYING TRACK/POSITION WHEN THE IGNITION WAS TURNED OFF. THESE CONCERN MAY BE CAUSED BY THE SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE THAT CONTROLS THE USB CONNECTION. TO IMPROVE THESE CONCERNS, THE SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE HAS BEEN CHANGED. NOTE: THE UPDATED SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE WILL ONLY ADDRESS SMS/TEXT CONCERNS FOR THE APPLE® IPHONE AT THIS TIME.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY HAVE THE BLIND SPOT MONITORING (BSM) OFF INDICATOR LIGHT FLASHING AND DTC U3000:54 STORED IN MEMORY. THE CONCERN IS CAUSED BY INADEQUATE BSM CONTROL MODULE CONTROL LOGIC. THE BSM CONTROL MODULE SOFTWARE HAS BEEN UPDATED TO ELIMINATE THIS CONCERN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT AN ABNORMAL STEERING FEEL AND/OR NOISE WHILE DRIVING THE VEHICLE IN FREEZING TEMPERA-TURES, HOWEVER, THERE IS NO LOSS OF STEERING CONTROL.THIS MAY BE DUE TO OIL SEEPAGE FROM THE POWER STEERING OIL PUMP PRESSURE SWITCH (A). THE OIL SEEPAGE IS CAUSED BY POOR SEALING OF THE OIL PRESSURE SWITCH O-RING AT LOW TEMPERATURE. THE SHAPE AND MATERIAL OF THE O-RING HAS BEEN CHANGED TO IMPROVE LOW TEMPERATURE SEALING PERFORMANCE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
WHEN DEALING WITH CUSTOMER COMPLAINTS OF EXCESSIVE CONDENSATION AND/OR WATER WITHIN THE HEADLAMP UNIT, FIRST DETERMINE IF ALL THE BULB SOCKETS ARE PRESENT AND CORRECTLY INSTALLED. IN MOST CASES YOU WILL FIND THAT THE BULB SEAL NO. 1 (A) OR HID BULB SEAL NO. 1 (B) AND BULB SEAL NO. 2 (C) SOCKET COVERS HAVE NOT BEEN CORRECTLY INSTALLED OR ARE MISSING DUE TO IMPROPER PRIOR REPAIRS (I.E., CUSTOMER REPLACING THE HEADLAMP BULBS OR BODY SHOP NOT TRANSFERRING THEM WHEN REPLACING THE HEADLAMP UNIT(S) DUE TO A COLLISION). ANY DAMAGE CAUSED BY MISSING SOCKET COVERS, HID MODULE SEAL (D), OR MISSING BUMPER BRACKETS (E) IS NOT COVERED BY WARRANTY POLICY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE SYMPTOMS MENTIONED BELOW, WHICH CAN BE FIXED WITH THE LATEST SOFTWARE UPDATE (VERSION 10.854 OR LATER).NAVIGATION SYSTEM FREEZES.MESSAGE WAITING FOR VALID GPS SIGNAL IS SHOWN IN THE MENU BAR OF NAVIGATION DISPLAY FOR SEVERAL MINUTES.VEHICLE SYMBOL IS OFF ROAD WHILE DRIVING / WRONG POSITION OF VEHICLE ON MAP.MAP IS ROTATING WHEN VEHICLE IS PARKED OR WHILE DRIVING.NAVIGATION SCREEN DONT APPEAR AFTER DEPRESSING NAVIGATION BUTTON. THEN IT DOES NOT RECOVER BY OPERATING ACC OFF TO ON POSITION.UNEXPECTED STOPPING VOICE CONTROL MESSAGE, USUALLY WHEN STARTING THE VEHICLE.CURRENT CAR POSITION (CCP) TURNING 180 DEGREES WHEN DRIVING IN REVERSE.THE MESSAGE WAITING FOR A VALID GPS SIGNAL APPEARS.RED SCREEN WITH MESSAGE "PROBLEM WITH MAP".YELLOW SCREEN WITH MESSAGE "INSERT SD CARD".NO MAP FOUND ERROR AND SD CARD CONTAINS A MAP.SCREEN TEMPORARILY GETS STUCK AT TOMTOM LOGO (SPLASH SCREEN) FOR 2 MINUTES DURING STARTUP. AFTERWARDS, THE NAVIGATION WILL NOT START UNTIL THE IGNITION IS CYCLED.SCREEN GETS STUCK AT TOMTOM LOGO (SPLASH SCREEN) DURING STARTUP.SCREEN LOCKS UP TO A "BLACK SCREEN.VEHICLE ICON JUMPS AROUND OR VIBRATES.IF NAVIGATION BUTTON IS PRESSED DURING AUDIO SCREEN, THE SCREEN FREEZES AND THE TOUCH SCREEN BECOMES INOPERATIVE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMPLAIN THAT THE STEERING WHEEL IS OFF CENTER MORE THAN 3° EVEN WHEN DRIVING STRAIGHT ON A FLAT ROAD. FOLLOW STEERING WHEEL ALIGNMENT PROCEDURE.
Source components: STEERING: STEERING WHEEL/HANDLE BAR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE SYMPTOMS MENTIONED BELOW, WHICH CAN BE FIXED WITH THE LATEST SOFTWARE UPDATE (VERSION 10.854 OR LATER).NAVIGATION SYSTEM FREEZES.MESSAGE WAITING FOR VALID GPS SIGNAL IS SHOWN IN THE MENU BAR OF NAVIGATION DISPLAY FOR SEVERAL MINUTES.VEHICLE SYMBOL IS OFF ROAD WHILE DRIVING / WRONG POSITION OF VEHICLE ON MAP.MAP IS ROTATING WHEN VEHICLE IS PARKED OR WHILE DRIVING.NAVIGATION SCREEN DONT APPEAR AFTER DEPRESSING NAVIGATION BUTTON. THEN IT DOES NOT RECOVER BY OPERATING ACC OFF TO ON POSITION.UNEXPECTED STOPPING VOICE CONTROL MESSAGE, USUALLY WHEN STARTING THE VEHICLE.CURRENT CAR POSITION (CCP) TURNING 180 DEGREES WHEN DRIVING IN REVERSE.THE MESSAGE WAITING FOR A VALID GPS SIGNAL APPEARS.RED SCREEN WITH MESSAGE "PROBLEM WITH MAP".YELLOW SCREEN WITH MESSAGE "INSERT SD CARD".NO MAP FOUND ERROR AND SD CARD CONTAINS A MAP.SCREEN TEMPORARILY GETS STUCK AT TOMTOM LOGO (SPLASH SCREEN) FOR 2 MINUTES DURING STARTUP. AFTERWARDS, THE NAVIGATION WILL NOT START UNTIL THE IGNITION IS CYCLED.SCREEN GETS STUCK AT TOMTOM LOGO (SPLASH SCREEN) DURING STARTUP.SCREEN LOCKS UP TO A "BLACK SCREEN.VEHICLE ICON JUMPS AROUND OR VIBRATES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY HAVE THE BLIND SPOT MONITORING (BSM) OFF INDICATOR LIGHT FLASHING AND DTC U3000:54 STORED IN MEMORY.THE CONCERN IS CAUSED BY INADEQUATE BSM CONTROL MODULE CONTROL LOGIC. THE BSM CONTROL MODULE SOFTWARE HAS BEEN UPDATED TO ELIMINATE THIS CONCERN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY EXPERIENCE DIFFICULTY MOVING THE SELECTOR LEVER OUT OF P RANGE AFTER THE VEHICLE HAS BEEN PARKED OVERNIGHT IN EXTREMELY COLD TEMPERATURES (I.E. BELOW FREEZING). THE SELECTOR LEVER MOVEMENT MAY RETURN TO NORMAL AFTER RUNNING THE CLIMATE CONTROL SYSTEM AT MAXIMUM HOT FOR SHORT PERIOD OF TIME. THIS CONCERN MAY BE CAUSED ACCIDENTALLY BY THE CUSTOMER SPILLING A DRINK AROUND THE SELECTOR LEVER. WHEN THE SPILLED LIQUID REACHES THE INTERLOCK CABLE AND FREEZES OVERNIGHT, IT CAUSES THE CUSTOMER TO HAVE DIFFICULTY MOVING THE SELECTOR LEVER OUT OF P RANGE THE NEXT MORNING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT BLUETOOTH® HANDS-FREE AND/OR TEXT MESSAGING RELATED CONCERNS. TO IMPROVE THE HANDLING OF BLUETOOTH® HANDS-FREE AND/OR TEXT MESSAGING CUSTOMER CONCERNS, MAZDA CRE-ATED A SPECIAL SERVICE AND PARTS EXCHANGE PROGRAM AS OF FEBRUARY 2010.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY HAVE THE BLIND SPOT MONITORING (BSM) OFF INDICATOR LIGHT FLASHING AND DTC U3000:54 STORED IN MEMORY.THE CONCERN IS CAUSED BY INADEQUATE BSM CONTROL MODULE CONTROL LOGIC. THE BSM CONTROL MODULE SOFTWARE HAS BEEN UPDATED TO ELIMINATE THIS CONCERN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
IN ACCORDANCE WITH FEDERAL REGULATIONS, FOLLOW THE PROCEDURE LISTED BELOW WHEN REPLACING A SPEEDOMETER.NOTE:MAZDA VEHICLES ARE MANUFACTURED WITH TAMPER-PROOF SPEEDOMETERS.WHEN A SPEEDOMETER IS REPLACED, THE NEW SPEEDOMETER WILL READ ZERO (0) MILES.THIS PROCEDURE IS EXTREMELY IMPORTANT TO ACCURATELY REPRESENT ACTUAL VEHICLE MILEAGE.PRIOR TO SPEEDOMETER REMOVAL, COMPLETE THE INFORMATION REQUIRED ON THE SPEEDOMETER REPLACE-MENT LABEL. LABELS CAN ONLY BE ORDERED THROUGH MSTORE, NOT MDCS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT THE CHECK ENGINE LIGHT ON WITH DTC P0456 STORED IN THE PCM MEMORY. P0456: EVAP SYSTEM LEAK DETECTED (VERY SMALL LEAK) THE CONCERN IS MOST LIKELY THE RESULT OF THE CUSTOMER NOT GETTING THE FUEL CAP COMPLETELY CLOSED AFTER FUELING THE VEHICLE. THIS CAUSES A SMALL FUEL VAPOR LEAK AND TURNS DTC P0456 ON.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS SERVICE BULLETIN PROVIDES INFORMATION REGARDING THE PROPER USE OF THE DRIVERS FLOOR MAT TO AVOID ANY POTENTIAL INTERFERENCE WITH THE FOOT PEDALS. THE FOLLOWING ARE POSSIBLE CAUSES OF FLOOR MAT INTERFERENCE, WHICH CAN BE AVOIDED WITH PROPER USAGE. FLOOR MAT MOVES FORWARD DUE TO IMPROPER INSTALLATION. INAPPROPRIATE FLOOR MAT (SUCH AS AFTERMARKET, NON-FACTORY-EQUIPPED, OR NON-GENUINE) IS USED. FLOOR MAT IS STACKED ONE ON TOP OF ANOTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
MAZDA NORTH AMERICAN OPERATIONS RECEIVED MANY REQUESTS FROM OUR DEALERS ASKING US TO APPROVE ADDITIONAL ON-CAR BRAKE LATHES AS AN OPTION FOR MNAO AUTHORIZED EQUIPMENT. DUE TO YOUR FEEDBACK AND AFTER EVALUATING A FEW ON-CAR BRAKE LATHES, WE ARE PLEASED TO ANNOUNCE THAT WE HAVE ADDED THE PRO CUT ON-CAR BRAKE LATHE TO MNAO AUTHORIZED EQUIPMENT PROGRAM. THE ACCU-TURN IS STILL AN APPROVED BRAKE LATHE BUT IT IS NO LONGER AVAILABLE FOR PURCHASE FROM OUR VENDOR. IMPORTANT REMINDER ROTORS MUST BE MACHINED USING A MAZDA APPROVED ON-CAR BRAKE LATHE OR WARRANTY CLAIMS ARE SUBJECT TO DENIAL OR DEBIT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMPLAIN THAT THE AMBIENT TEMPERATURE DISPLAY IS NOT ACCURATE, OR IT TAKES TOO LONG FOR THE DISPLAY TO SHOW ACTUAL TEMPERATURE.WHEN YOU ENCOUNTER A CUSTOMER WITH THIS CONCERN, FIRST VERIFY THE CONDITION WHEN THE CUSTOMER NOTICED THIS SYMPTOM. IF THE CONDITION IS SIMILAR TO THE FOLLOWING CONTROL LOGIC OF AMBIENT TEMPERATURE OR DIF-FERENCE BETWEEN THE TEMPERATURE DISPLAY AND OTHERS, ADVISE THE CUSTOMER THAT THIS IS A NOR-MAL CHARACTERISTIC OF THE VEHICLE AND NOT A MALFUNCTION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES EXHIBIT BRAKE RELATED CONCERNS SUCH AS BRAKE NOISE, BRAKE JUDDER OR BRAKE DRAGGING. IF YOU ENCOUNTER A CUSTOMER COMPLAINT FOR ANY ONE OF THESE SYMPTOMS, REFER TO THE FOLLOWING INFORMATION TO UNDERSTAND WHY SYMPTOMS MAY OCCUR, AND TO BETTER ASSIST THE CUSTOMER IN RESOLVING THEIR SPECIFIC BRAKE CONCERN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE SYMPTOMS MENTIONED BELOW, WHICH CAN BE FIXED WITH THE LATEST SOFTWARE UPDATE (VERSION 10.852 OR LATER). VEHICLE ICON JUMPS AROUND OR VIBRATES. CAUTION: DO NOT USE THE FACTORY RESET FOR RETAIL VEHICLES. OTHERWISE, PERSONAL SETTINGS (SUCH AS DISPLAY AND SOUND ADJUSTMENTS) WILL BE LOST, INCLUDING FAVORITES INFORMATION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
IN SUPPORT OF THE 2007-14 CX-9, MAZDA WILL SHIP TO ALL DEALERS ONE (1) NEW SPECIAL SERVICE TOOL (SST). THE SST WILL BE SHIPPED AUTOMATICALLY BY MAZDAS TOOL VENDOR SNAP-ON TOOLS DURING THE MONTH OF APRIL 2014, AND COM-PLETING IN MAY 2014.THE INITIAL SHIPMENT IN APRIL WILL BE MADE TO A LIMITED NUMBER OF DEALERS WITH A HIGHER THAN AVERAGE RATE OF REPAIRS, WITH ALL REMAINING DEALERS RECEIVING THE SST IN MAY 2014.THE FOLLOWING SST IS THE LATEST ADDITION TO THE MAZDA REQUIRED TOOL (MRT) LIST.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE SYMPTOMS MENTIONED BELOW, WHICH CAN BE FIXED WITH THE LATEST SOFTWARE UPDATE (VERSION 10.852 OR LATER). VEHICLE ICON JUMPS AROUND OR VIBRATES. CAUTION: DO NOT USE THE FACTORY RESET FOR RETAIL VEHICLES. OTHERWISE, PERSONAL SETTINGS (SUCH AS DISPLAY AND SOUND ADJUSTMENTS) WILL BE LOST, INCLUDING FAVORITES INFORMATION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Mazda Motor Corporation is extending the warranty coverage for power transfer unit (PTU) replacement on certain 2010-2014 CX-9 vehicles with AWD and produced from July 28, 2009 through December 2, 2013. The warranty for this repair will be extended to 7 years (84 months) from the original warranty start date or 90,000 miles, whichever comes first. On some vehicles, when driving under high load or at high speeds, increased oil temperature inside the transfer unit may result in poor lubrication. Continued driving under these conditions may create abnormal noise, damage the transfer unit, and oil leakage. Dealers are instructed to replace the PTU. Please refer to Attachments I and II for details.
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
MAZDA: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. ON SOME ALL WHEEL DRIVE (AWD) VEHICLES, WARRANTY COVERAGE FOR VACUUM POWER BREAK BOOSTER UNITS SPECIFIC REPAIRS HAS BEEN EXTENDED TO 90,000 MILES OR 7 YEARS FROM ORIGINAL WARRANTY START DATE. MODEL 2010-2014 CX9. *PE
Source components: SERVICE BRAKES, HYDRAULIC:POWER ASSIST:VACUUM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
WHEN REPLACING THE SIRIUSXM SATELLITE RADIO UNIT (OR A MAZDA CONNECT TUNER AND AMP UNIT (TAU)) WITH REPLACEMENT TUNER FOR ANY REASON, A CALL MUST BE MADE TO INFORM SIRIUSXM OF THE EXISTING RADIO ID AND THE NEW/ REPLACEMENT SAT RADIO ID AS SOON AS POSSIBLE TO ENSURE THE CUSTOMER LEAVES THE DEALERSHIP WITH ACTIVE (WORKING SAT RADIO.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE ONE OR MORE OF THE FOLLOWING BLUETOOTH® SYMPTOMS: WHEN THE VEHICLE STARTED, THE REGISTERED DEVICE WOULD NOT CONNECT WITH THE BLUETOOTH® SYSTEM. THE BLUETOOTH, USB OR PANDORA TAB ON THE AUDIO DISPLAY WOULD NOT ILLUMINATE (GRAY OUT). THE BLUETOOTH, USB OR PANDORA TAB ON THE AUDIO DISPLAY WOULD ILLUMINATE, BUT THE BLUETOOTH® SYSTEM WOULD NOT OPERATE. WHEN THE CUSTOMER PRESSES THE TALK BUTTON ON THE STEERING WHEEL, THE AUDIO DISPLAY MOMENTARILY SHOWS A MESSAGE STARTING UP BLUETOOTH PLEASE WAIT THEN THE BLUETOOTH® UNIT DOES NOT WORK. NOTE: PHONE PAIRED - THE STEERING WHEEL PICKUP BUTTON WILL ONLY ANSWER PHONE CALLS. PHONE NOT PAIRED - THE STEERING WHEEL PICKUP BUTTON WILL INITIATE BLUETOOTH® PAIRING FUNCTION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THE NAVIGATION SYSTEM SUPPORT FOR DIAGNOSTICS, PARTS AUTHORIZATION, AND PARTS EXCHANGE REQUIRE CONTACTING THE PROPER SOURCE. TOMTOM NAVIGATION HELP DESK AT 866-486-6866 FROM 7AM-11PM (M-F) AND 9AM-8PM (SAT) EASTERN STANDARD TIME. NOTE: ONE OF THE FIRST STEPS FOR TROUBLESHOOTING THE NAVIGATION SYSTEM IS FOR THE CUSTOMER OR DEALER TO CALL TOMTOM. IF THE TOMTOM CALL CENTER CANNOT SOLVE THE CUSTOMERS PROBLEM, THEY WILL PROVIDE A CASE NUMBER TO THE CUSTOMER THAT CAN BE REFERRED TO IF NEEDED. SERVICE ADVISORS SHOULD GET THIS CASE NUMBER FROM THE CUSTOMER IF THE VEHICLE COMES INTO THE DEALER FOR FURTHER DIAGNOSIS SO THE TECHNICIAN CAN HAVE IT WHEN CALLING TOMTOM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
AN UPDATED VERSION OF THE SOFTWARE FOR THE TOMTOM NAVIGATION SYSTEM HAS BECOME AVAILABLE. UNDER THIS MSP42, THE NAVIGATION SYSTEM WILL BE REFLASHED TO THE UPDATED VERSION USING A SD CARD. THIS SOFTWARE UPDATE WILL ELIMINATE CANCELING VOICE RECOGNITION WHEN VEHICLE SPEED TRANSITIONS PAST 4MPH AND IMPROVE THE FOLLOWING: SYSTEM STABILITY SPEECH RECOGNITION VERBAL AND VISUAL INSTRUCTIONS FOR ROUTE GUIDANCE (3D VIEW NOW INCLUDES MORE VISUAL FEEDBACK SUCH AS ARROWS INDICATING WHICH LANE TO USE IN COMPLICATED INTERCHANGES) COMMANDER SWITCH CONTROL (FOR VEHICLES EQUIPPED) GPS RECOVERY AFTER SIGNAL IS LOST (TUNNELS, PARKING GARAGES, ETC.) CAUTION: DO NOT USE THE FACTORY RESET FOR RETAIL VEHICLES. OTHERWISE, PERSONAL SETTINGS (SUCH AS DISPLAY AND SOUND ADJUSTMENTS) WILL BE LOST, INCLUDING FAVORITES INFORMATION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
AN UPDATED VERSION OF THE SOFTWARE FOR THE TOMTOM NAVIGATION SYSTEM HAS BECOME AVAILABLE. UNDER THIS MSP42, THE NAVIGATION SYSTEM WILL BE REFLASHED TO THE UPDATED VERSION USING A SD CARD. THIS SOFTWARE UPDATE WILL ELIMINATE CANCELING VOICE RECOGNITION WHEN VEHICLE SPEED TRANSITIONS PAST 4MPH AND IMPROVE THE FOLLOWING: SYSTEM STABILITY SPEECH RECOGNITION VERBAL AND VISUAL INSTRUCTIONS FOR ROUTE GUIDANCE (3D VIEW NOW INCLUDES MORE VISUAL FEEDBACK SUCH AS ARROWS INDICATING WHICH LANE TO USE IN COMPLICATED INTERCHANGES) COMMANDER SWITCH CONTROL (FOR VEHICLES EQUIPPED) GPS RECOVERY AFTER SIGNAL IS LOST (TUNNELS, PARKING GARAGES, ETC.) CAUTION: DO NOT USE THE FACTORY RESET FOR RETAIL VEHICLES. OTHERWISE, PERSONAL SETTINGS (SUCH AS DISPLAY AND SOUND ADJUSTMENTS) WILL BE LOST, INCLUDING FAVORITES INFORMATION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMPLAIN OF CONDENSATION/FOG INSIDE THE FRONT OR REAR COMBINATION LIGHTS. THE RECENT NEW MODELS HAVE BEEN FITTED WITH A CLEAR LENS WHICH CAN CAUSE THE SYMPTOM TO BE MORE NOTICEABLE, HOWEVER, IT DOES NOT AFFECT THE PERFORMANCE OF THE LIGHT. THIS CONDENSATION/FOG IS A NATURAL PHENOMENON THAT OCCURS WHEN THERE IS A FAIRLY LARGE TEMPERATURE DIFFERENCE BETWEEN THE INSIDE AND THE OUTSIDE OF THE LIGHT HOUSING. IT IS NORMAL FOR VERY SMALL WATER DROPS TO APPEAR IN CERTAIN LOCATIONS ON THE LIGHT UNITS WHERE THE AIR IS STAGNANT (CONDENSATION), MAKING THE LENS LOOK WHITISH (FOG). THIS HAPPENS MOSTLY IN THE CORNERS AND NARROW SPACES, AND WILL TYPICALLY CLEAR DURING WARMER AMBIENT TEMPERATURES, OR WHEN THE LIGHTS HAVE BEEN ON FOR SOME TIME. EXPLAIN TO THE CUSTOMER THAT THIS IS A NATURAL PHENOMENON AND NOT A QUALITY DEFECT. DO NOT ATTEMPT REPAIRS AS THIS IS CONSIDERED NORMAL, AND IS NOT COVERED UNDER WARRANTY. REPLACING THE LIGHT UNIT WILL NOT CORRECT THIS SYMPTOM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY REPORT A SLIGHT CLUNK/BANG/BUZZ NOISE OR JOLT FROM THE FRONT OF THE VEHICLE. THIS CONCERN WILL MOST LIKELY OCCUR DURING THE VEHICLES FIRST FORWARD MOVEMENT AFTER STARTING THE ENGINE. THIS IS A NORMAL OPERATING NOISE OF THE ANTI-LOCK BRAKE SYSTEM (ABS). DO NOT ATTEMPT ANY REPAIRS.
Source components: SERVICE BRAKES, AIR:ANTILOCK:ABS WARNING LIGHT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE ONE OR MORE OF THE FOLLOWING BLUETOOTH SYMPTOMS: WHEN THE VEHICLE STARTED, THE REGISTERED DEVICE WOULD NOT CONNECT WITH THE BLUETOOTH SYSTEM AND BLUETOOTH TAB ON THE AUDIO DISPLAY WOULD NOT ILLUMINATE (GRAY OUT). THE BLUETOOTH TAB ON THE AUDIO DISPLAY WOULD ILLUMINATE, BUT THE BLUETOOTH SYSTEM WOULD NOT OPERATE. WHEN THE CUSTOMER PRESSES THE TALK BUTTON ON THE STEERING WHEEL, THE AUDIO DISPLAY MOMENTARILY SHOWS A MESSAGE STARTING UP BLUETOOTH PLEASE WAIT THEN THE BLUETOOTH UNIT DOES NOT WORK. NOTE: PHONE PAIRED - THE STEERING WHEEL PICKUP BUTTON WILL ONLY ANSWER PHONE CALLS. PHONE NOT PAIRED - THE STEERING WHEEL PICKUP BUTTON WILL INITIATE BLUETOOTH PAIRING FUNCTION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE STAINS APPEARING ON THE HOOD, ROOF AND/OR TRUNK OF THE VEHICLE. THIS CONCERN IS MOST LIKELY TO BE FOUND IN A COLD WEATHER AREAS JUST AFTER THE RAPGARD IS REMOVED AT PDI. THIS MAY BE CAUSED BY MOISTURE WHICH HAS BEEN TRAPPED AND CONDENSED BETWEEN THE PAINT AND THE RAPGARD. THESE TYPES OF STAINS CAN BE REMOVED WITH A HEAT GUN OR AN INFRARED DRIER.IF YOU ENCOUNTER THIS CONCERN DURING PDI, USE A HEAT GUN OR AN INFRARED DRIER TO APPLY HEAT TO THE AFFECTED AREA TO REMOVE THE STAIN(S).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains.Use extra care when cleaning wheels. The following are guidelines to follow when cleaning the wheels.-Mazda recommends using a mild soap or neutral detergent as stated in the owner's manual under Appear-ance Care in the Maintenance and Care section.-DO NOT use a cleaning products containing strong acid or alkali contents to clean the wheels.-DO NOT apply any type of specialized wheel cleaner to the wheels when they are hot (such as after driving the vehicle or if the vehicle has sat in the sun). Ensure wheel temperatures are the same as ambient tem-perature before cleaning.-Within 15 minutes after any cleaner is applied, rinse the wheel thoroughly to completely remove cleaner.-Stains on Mazda Wheels caused by improper cleaning are not covered under the Mazda Vehicle Warranty.
NHTSA source summary · Original PDF not reviewed by Recallfolio
A MUSTY/MILDEW TYPE ODOR MAY COME FROM THE VENTS WHEN THE AIR CONDITIONING (A/C) SYSTEM IS OPERATING. IT IS MOST NOTICEABLE WHEN THE A/C IS FIRST TURNED ON. THIS ODOR IS THE RESULT OF MOLD GROWTH IN THE A/C EVAPORATOR/COOLING UNIT WHICH IS CAUSED BY CONDENSATION, DUST, AND POLLEN WITHIN THE COOLING UNIT. THIS CONDITION IS USUALLY WORSE DURING HIGH HUMIDITY CONDITIONS. MAZDA AIR COOLING COIL COATING IS AVAILABLE TO ENCAPSULATE THE MOLD TO REDUCE ODORS. IF THE PRODUCT IS PROPERLY APPLIED, IT CAN EFFECTIVELY REDUCE THE MUSTY/MILDEW ODOR FOR UP TO THREE YEARS.NOTE:SEE PARTS INFORMATION FOR MAZDA AIR COOLING COIL COATING AND KIT PART NUMBERS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY EXPERIENCE A WATER LEAK FROM THE SUNROOF AFTER WASHING THE VEHICLE WITH A HIGH-PRESSURE CAR WASH SYSTEM. HIGH PRESSURE WATER FROM THE CAR WASH MAY DRIP FROM THE DRIP RAIL AND LEAK INTO THE CABIN.