Original record summaries, dates and identifiers for this model-year. Records 501–600 of 602, ordered newest first. Dated records on this page: Jan 14, 2014–Jun 24, 2015.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Jun 24, 2015Service Bulletin/Repair Instructions
09-025-15-3057
NHTSA communication ID: 10099232
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT EITHER AN AUDIO SCREEN THAT IS LOCKING-UP (BLACK SCREEN) OR AN INOPERATIVE AUDIO TOUCH SCREEN. IN BOTH CASES HOWEVER, THE AUDIO UNIT SOUND OUTPUT IS NORMAL. THIS CONCERN MAY BE CAUSED BY AN INTERNAL FAILURE OF THE AUDIO UNIT. THE PRODUCTION PROCESS AT THE AUDIO SUPPLIER HAS BEEN IMPROVED TO ELIMINATE THESE CONCERNS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT ON WITH DTC P0300:00, P0301:00, P0302:00, P0303:00 AND/OR P0304:00 STORED IN MEMORY AND ACCOMPANIED WITH AN INCREASED ENGINE OIL LEVEL. P0300:00: RANDOM MISFIRE DETECTED P0301:00: CYLINDER NO.1 MISFIRE DETECTED P0302:00: CYLINDER NO.2 MISFIRE DETECTED P0303:00: CYLINDER NO.3 MISFIRE DETECTED P0304:00: CYLINDER NO.4 MISFIRE DETECTED THIS IS CAUSED BY IMPROPER CONTROL LOGIC OF THE PCM. IN COLD WEATHER BELOW 14 °F (-10 °C) WITH REPEATED SHORT TIME OPERATION, EXCESS FUEL INJECTED IN THE CYLINDERS MAY ACCUMULATE IN THE CRANK CASE AND RESULT IN INCREASED OIL LEVEL AND MISFIRE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE A LACK OF POWER DURING HARD ACCELERATION (APPROX. 6,000 RPM) IN COLD WEATHER CONDITIONS BELOW 32 °F (0 °C). DTCS P0300:00, P0301:00 AND/OR P0302:00 ARE STORED IN MEMORY. P0300:00: RANDOM MISFIRE DETECTED P0301:00: CYLINDER NO. 1 MISFIRE DETECTED P0302:00: CYLINDER NO. 2 MISFIRE DETECTED THIS IS CAUSED BY IMPROPER CONTROL LOGIC OF THE PCM. THE PCM MAY DETECT A FALSE MISFIRE UNDER THE SUBJECT CONDITIONS AND MAY FALL INTO FAIL SAFE MODE. TO ELIMINATE THIS CONCERN, THE PCM CONTROL LOGIC HAS BEEN CHANGED.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES (WITHOUT POWER SEATS) MAY EXHIBIT A DRIVER SEAT THAT GRADUALLY MOVES DOWN BY ITSELF. THIS CONCERN MAY BE CAUSED WHEN A LOAD, WHICH IS APPLIED TO THE SEAT DURING BRAKING, EXCEEDS A CERTAIN LEVEL THAT COULD IMPACT THE RETAINING MECHANISM OF THE SEAT LIFTER CAUSING THE SEAT TO GRADUALLY MOVE DOWNWARD. TO ELIMINATE THIS CONCERN, THE PLAY IN THE LIFT MECHANISM GEARS HAS BEEN REDUCED.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH ONE OR MORE OF THESE DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780). P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ON P0780:00 - GEAR SHIFTING MALFUNCTION THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO CORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT A CHECK ENGINE LIGHT ON WITH DTC P013A:00 STORED IN MEMORY. DTC P013A:00: HO2S SLOW RESPONSE (DURING TRANSITION FROM RICH TO LEAN) THIS CONCERN MAY BE CAUSED BY AN IMPACT FROM A SPEED-BUMP OR OTHER SOURCE, CAUSING A DEFORMATION OF THE GASKET BETWEEN THE EXHAUST MANIFOLD (WU-TWC) (A) AND THE TWC (B).
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT A CONDITION IN EXTREMELY COLD TEMPERATURES (BELOW FREEZING) WHERE THE HATCHBACK WILL NOT LATCH (HALF LATCH) WHEN CLOSING. THIS IS CAUSED BY THE TOPPER RUBBER, A COMPONENT OF THE LIFTGATE LATCH AND LOCK ACTUATOR (A), HARDENING WHEN THE TEMPERATURE DROPS BELOW FREEZING. THE STOPPER RUBBER HAS NOW BEEN IMPROVED TO ELIMINATE THIS CONCERN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT A PAINT BLISTER (A) AND/OR RUST SPOT (B) ON THE LOWER PORTION OF THE LIFTGATE PANEL AS SHOWN BELOW. THE THICKNESS OF THE PAINT MAY BE INSUFFICIENT, CAUSING DECREASED CORROSION RESISTANCE. HOWEVER, THE THICKNESS OF CLEAR HAS BEEN INCREASED TO ELIMINATE THIS CONCERN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE A RATTLE NOISE FROM THE FRONT DOOR GLASS WHEN DRIVING WITH THE WINDOW OPEN APPROX. 1/2 TO 4 INCHES (1 - 10 CM). THE RATTLE NOISE MAY BE CAUSED BY INSUFFICIENT HOLDING FORCE OF THE GLASS RUN CHANNEL. TO INCREASE THE HOLDING FORCE, THE SHAPE OF GLASS RUN CHANNEL HAS BEEN CHANGED AND NON-WOVEN PADS HAVE BEEN ATTACHED TO THE GLASS RUN CHANNEL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT A CHIRP/CLUNK TYPE NOISE FROM THE REAR SHOCK ABSORBERS (A) WHEN DRIVING ON A ROUGH ROAD OR PASSING OVER A SPEED BUMP. VISUAL INSPECTION OF THE SHOCK ABSORBERS SHOW NO EXTERNAL DAMAGE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT THE CHECK ENGINE LIGHT ON WITH DTC P0456 STORED IN THE PCM MEMORY. P0456: EVAP SYSTEM LEAK DETECTED (VERY SMALL LEAK) THE CONCERN IS MOST LIKELY THE RESULT OF THE CUSTOMER NOT GETTING THE FUEL CAP COMPLETELY CLOSED AFTER FUELING THE VEHICLE. THIS CAUSES A SMALL FUEL VAPOR LEAK AND TURNS DTC P0456 ON.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE A CHECK ENGINE LIGHT ON WITH DTCS P0011:00 AND/OR DTC P0012:00 STORED IN MEMORY. P0011:00: ELECTRIC VARIABLE VALVE TIMING CONTROL SYSTEM - OVER-ADVANCED) P0012:00: ELECTRIC VARIABLE VALVE TIMING CONTROL SYSTEM - (OVER-RETARDED) THIS CONCERN MAY BE CAUSED BY VARIABLE VALVE TIMING (VVT) ACTUATOR SPRING SHAFT FATIGUE. DURING VEHICLE USAGE, THE SPRING SHAFT MAY FAIL AND CAUSE INCORRECT VVT OPERATION AND CHECK ENGINE LIGHT ILLUMINATION. THE INSPECTION PROCEDURE HAS BEEN IMPROVED TO ELIMINATE THIS CONCERN IN THE FUTURE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
WHEN FOLDING THE REAR SEAT BACK FORWARD, THE HEAD RESTRAINT (B) MAY CATCH ON THE FRONT SEAT BACK POCKET (A). IF WEIGHT IS APPLIED TO THE REAR SEAT AT THIS TIME (I.E. PASSENGER PUSHES ON REAR SEAT, ETC.), THE FRONT SEAT BACK POCKET MAY BECOME TORN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH ONE OR MORE OF THESE DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780). P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ON P0780:00 - GEAR SHIFTING MALFUNCTION THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO CORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT ON WITH DTC P0300:00, P0301:00, P0302:00, P0303:00 AND/OR P0304:00 STORED IN MEMORY AND ACCOMPANIED WITH AN INCREASED ENGINE OIL LEVEL. P0300:00: RANDOM MISFIRE DETECTED P0301:00: CYLINDER NO.1 MISFIRE DETECTED P0302:00: CYLINDER NO.2 MISFIRE DETECTED P0303:00: CYLINDER NO.3 MISFIRE DETECTED P0304:00: CYLINDER NO.4 MISFIRE DETECTED THIS IS CAUSED BY IMPROPER CONTROL LOGIC OF THE PCM. IN COLD WEATHER BELOW 14 °F (-10 °C) WITH REPEATED SHORT TIME OPERATION, EXCESS FUEL INJECTED IN THE CYLINDERS MAY ACCUMULATE IN THE CRANK CASE AND RESULT IN INCREASED OIL LEVEL AND MISFIRE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH ONE OR MORE OF THESE DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780). P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ON P0780:00 - GEAR SHIFTING MALFUNCTION. THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO ORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMPLAIN ABOUT ONE OR MORE OF THE FOLLOWING CONCERNS. 1. SMS/TEXT CANNOT BE DOWNLOADED WHEN CONNECTED VIA BLUETOOTH. 2. OPERATIONAL CONCERNS WHEN PLAYING A MEDIA DEVICE (IPOD, USB STICK ETC.) CONNECTED VIA THE USB PORT. A. AFTER THE IGNITION IS TURNED ON, IT TAKES A LONG TIME TO LOAD ALL THE DATA FROM THE DEVICE EFORE STARTING PLAYBACK. DEPENDING ON THE DATA VOLUME, IT CAN TAKE UP TO SEVERAL MINUTES. B. AFTER THE IGNITION IS TURNED ON, THE PLAYBACK ALWAYS STARTS FROM THE FIRST TRACK. IT DOES NOT START FROM THE LAST PLAYING TRACK/POSITION WHEN THE IGNITION WAS TURNED OFF. C. IPOD ERROR MESSAGE FOR THE APPLE® IOS 8.0 OR HIGHER SOFTWARE ON IPHONE 4, 5, OR 6. THESE CONCERNS MAY BE CAUSED BY THE SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE THAT CONTROLS THE USB CONNECTION. TO IMPROVE THESE CONCERNS, THE SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE HAS BEEN CHANGED. NOTE: THE UPDATED SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE WILL ONLY ADDRESS SMS/TEXT CONCERNS FOR THE APPLE® IPHONE AT THIS TIME.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH ONE OR MORE OF THESE DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780). P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ON P0780:00 - GEAR SHIFTING MALFUNCTION. THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO ORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMPLAIN ABOUT ONE OR MORE OF THE FOLLOWING CONCERNS. 1. SMS/TEXT CANNOT BE DOWNLOADED WHEN CONNECTED VIA BLUETOOTH. 2. OPERATIONAL CONCERNS WHEN PLAYING A MEDIA DEVICE (IPOD, USB STICK ETC.) CONNECTED VIA THE USB PORT. A. AFTER THE IGNITION IS TURNED ON, IT TAKES A LONG TIME TO LOAD ALL THE DATA FROM THE DEVICE BEFORE STARTING PLAYBACK. DEPENDING ON THE DATA VOLUME, IT CAN TAKE UP TO SEVERAL MINUTES. B. AFTER THE IGNITION IS TURNED ON, THE PLAYBACK ALWAYS STARTS FROM THE FIRST TRACK. IT DOES NOT START FROM THE LAST PLAYING TRACK/POSITION WHEN THE IGNITION WAS TURNED OFF. THESE CONCERN MAY BE CAUSED BY THE SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE THAT CONTROLS THE USB CONNECTION. TO IMPROVE THESE CONCERNS, THE SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE HAS BEEN CHANGED. NOTE: THE UPDATED SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE WILL ONLY ADDRESS SMS/TEXT CONCERNS FOR THE APPLE® IPHONE AT THIS TIME. THE UPDATED SOFTWARE OF THE BLUETOOTH/HANDSFREE MODULE WILL NOT ADDRESS THE IPOD ERROR MESSAGE CONCERN FOR THE APPLE® IOS 8.0 OR HIGHER SOFTWARE ON IPHONE 4, 5, OR 6 AT THIS TIME.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT INSTRUMENT CLUSTER TPMS, ABS AND TCS/DSC INDICATOR WARNING LIGHTS ON AND DTC U3000:49[STANDARD DEPLOYMENT CONTROL SYSTEM] OR C0061:29, C0062:29, C0063:29 [STANDARD DEPLOYMENT CONTROL SYSTEM] STORED IN MEMORY. THE AIRBAG, SCBS, AT, MRCC, LDWS AND HBC INSTRUMENT CLUSTER INDICATOR LIGHTS MAY ALSO COME ON. INTERNAL FAILURE OF THE SAS CONTROL MODULE MAY BE THE CAUSE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH ONE OR MORE OF THESE DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780). P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ON P0780:00 - GEAR SHIFTING MALFUNCTION. THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO ORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
USE THE FOLLOWING REPAIR PROCEDURE TO MINIMIZE THE NEED TO REPLACE THE CATALYST CONVERTER/EXHAUST PIPE WHEN REMOVING OXYGEN SENSORS AND/OR AIR FUEL RATIO SENSORS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE STAINS APPEARING ON THE HOOD, ROOF AND/OR TRUNK OF THE VEHICLE. THIS CONCERN IS MOST LIKELY TO BE FOUND IN A COLD WEATHER AREAS JUST AFTER THE RAPGARD IS REMOVED AT PDI. THIS MAY BE CAUSED BY MOISTURE WHICH HAS BEEN TRAPPED AND CONDENSED BETWEEN THE PAINT AND THE RAPGARD. THESE TYPES OF STAINS CAN BE REMOVED WITH A HEAT GUN OR AN INFRARED DRIER. IF YOU ENCOUNTER THIS CONCERN DURING PDI, USE A HEAT GUN OR AN INFRARED DRIER TO APPLY HEAT TO THE AFFECTED AREA TO REMOVE THE STAIN(S).
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMPLAIN ABOUT ONE OR MORE OF THE FOLLOWING CONCERNS. 1. SMS/TEXT CANNOT BE DOWNLOADED WHEN CONNECTED VIA BLUETOOTH. 2. OPERATIONAL CONCERNS WHEN PLAYING A MEDIA DEVICE (IPOD, USB STICK ETC.) CONNECTED VIA THE USB PORT. A. AFTER THE IGNITION IS TURNED ON, IT TAKES A LONG TIME TO LOAD ALL THE DATA FROM THE DEVICE BEFORE STARTING PLAYBACK. DEPENDING ON THE DATA VOLUME, IT CAN TAKE UP TO SEVERAL MINUTES. B. AFTER THE IGNITION IS TURNED ON, THE PLAYBACK ALWAYS STARTS FROM THE FIRST TRACK. IT DOES NOT START FROM THE LAST PLAYING TRACK/POSITION WHEN THE IGNITION WAS TURNED OFF. THESE CONCERN MAY BE CAUSED BY THE SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE THAT CONTROLS THE USB CONNECTION. TO IMPROVE THESE CONCERNS, THE SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE HAS BEEN CHANGED. NOTE: THE UPDATED SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE WILL ONLY ADDRESS SMS/TEXT CONCERNS FOR THE APPLE® IPHONE AT THIS TIME.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES (WITHOUT POWER SEATS) MAY EXHIBIT A DRIVER SEAT THAT GRADUALLY MOVES DOWN BY ITSELF. THIS CONCERN MAY BE CAUSED WHEN A LOAD, WHICH IS APPLIED TO THE SEAT DURING BRAKING, EXCEEDS A CERTAIN LEVEL THAT COULD IMPACT THE RETAINING MECHANISM OF THE SEAT LIFTER CAUSING THE SEAT TO GRADUALLY MOVE DOWNWARD. TO ELIMINATE THIS CONCERN, THE PLAY IN THE LIFT MECHANISM GEARS HAS BEEN REDUCED.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT A KNOCKING / SQUEAKING NOISE FROM THE FRONT STRUT BEARING (A) WHEN DRIVING ON ROUGH ROADS AND/OR WHEN TURNING THE STEERING WHEEL WHILE THE VEHICLE IS STOPPED. THE NOISE MAY BE DUE TO UPPER FRONT STRUT BEARING DAMAGE OR IT MAY BE DUE TO STICK/SLIP BETWEEN THE FRONT STRUT BEARING AND COIL SPRING. TO ELIMINATE THE NOISE, THE FOLLOWING MASS-PRODUCTION CHANGES HAVE BEEN MADE: 1. THE MATERIAL AND PRODUCTION METHOD OF THE FRONT STRUT BEARING HAS BEEN CHANGED. 2. A PROTECTOR HAS BEEN INSTALLED ONTO THE COIL SPRING. NOTE: THE PISTON ROD NUT (B) REQUIRES REPLACEMENT WHEN THE FRONT STRUT BEARING IS REPLACED.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT AN INOPERATIVE SEAT WARMER (OR SEAT HEATER) ON THE DRIVER AND/OR PASSENGER SEAT. WHEN WEIGHT IS APPLIED TO THE SEAT, PART OF THE HEATER ELEMENT WIRE MAY COME OUT OF POSITION AND BECOME BENT. UNDER REPEATED STRESS, THE WIRE MAY BREAK CAUSING AN INOPERATIVE SEAT WARMER CONDITION. AN ADDITIONAL ADHESION TREATMENT HAS BEEN APPLIED TO ELIMINATE THE HEATER ELEMENT WIRE FROM COMING OUT OF THE POSITION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMPLAIN ABOUT NO COOL AIR FROM THE VENTS WHEN THE AIR CONDITIONER (A/C) IS ON. THIS CONCERN MAY BE CAUSED BY A/C REFRIGERANT LEAKING FROM THE EVAPORATOR. SOME DEFORMED EVAPORATOR TUBES SLIPPED THROUGH QUALITY INSPECTION AND WERE USED DURING PRODUCTION. A/C REFRIGERANT LEAKS FROM IMPROPER BRAZING AT A JOINT. TO CORRECT THE PROBLEM, THE PRODUCTION AND INSPECTION CONTROL OF THE EVAPORATOR HAVE BEEN IMPROVED.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES (ONLY EQUIPPED WITH MANUAL A/C OR WITHOUT A/C) MAY EXHIBIT A BLOWER MOTOR THAT ONLY OPERATES IN THE HIGHEST SPEED (4TH) AND DOES NOT OPERATE AT SPEEDS 1 - 3. THIS CONCERN OCCURS MOSTLY IN COLDER REGIONS AND MAY BE CAUSED BY A BLOWN RESISTOR FUSE. TO ELIMINATE THIS CONCERN, A SPECIAL SERVICE PART BLOWER MOTOR HAS BEEN ESTABLISHED.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT ONE OF THE FOLLOWING CONCERNS: HARD TO SHIFT INTO 3RD, 4TH, 5TH, AND/OR 6TH GEAR. SOMETIMES THE SHIFTER MAY JUMP OUT OF 3RD GEAR OVER A ROAD BUMP WHEN ACCELERATING AFTER DECELERATION AT 25-40 MPH (40-65 KM/H) THIS IS CAUSED BY A FAILURE OF THE RELATED CLUTCH HUB(S). TO CORRECT THE PROBLEM OF HARD SHIFTING, THE SHAPE OF THE 3-4 AND 5-6 CLUTCH HUB HAS BEEN CHANGED. A SURFACE TREATMENT HAS NOW BEEN ADDED TO THE 3-4 CLUTCH HUB TO PREVENT 3RD GEAR FROM JUMPING OUT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT A CHIRP/CLUNK TYPE NOISE FROM THE REAR SHOCK ABSORBERS (A) WHEN DRIVING ON A ROUGH ROAD OR PASSING OVER A SPEED BUMP. VISUAL INSPECTION OF THE SHOCK ABSORBERS SHOW NO EXTERNAL DAMAGE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT A CREAKING NOISE FROM UNDER THE FRONT OF THE VEHICLE WHEN DRIVING OVER BUMPS. THE NOISE OCCURS AT APPROX. 12 - 25 MPH (20 - 40 KM/H) WHEN THE ROAD SURFACE IS WET OR AFTER A CAR WASH. THE NOISE BECOMES MORE NOTICEABLE WHEN DRIVING OVER HIGHER BUMPS. THE CREAKING NOISE IS CAUSED WHEN THE FRONT LOWER CONTROL ARM BUSHING(S) (A) BECOME WET.
NHTSA source summary · Original PDF not reviewed by Recallfolio
IN SUPPORT OF THE SKYACTIV MODELS, MAZDA WILL MAKE AVAILABLE A SPECIAL SERVICE TOOL (SST), TO ADDRESS FRONT SUSPENSION NOISE FOR SPECIFIC HIGH HUMIDITY AND WET CLIMATE CONDITIONS IN THE LOWER GULF STATES. THE SST WILL BE NEEDED TO COMPLETE REPAIRS DETAILED IN TSB 02-005/14 AND IS AVAILABLE THROUGH MAZDAS TOOL VENDOR, SNAP-ON TOOLS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT ON WITH DTC P0300:00, P0301:00, P0302:00, P0303:00 AND/OR P0304:00 STORED IN MEMORY AND ACCOMPANIED WITH AN INCREASED ENGINE OIL LEVEL.P0300:00: RANDOM MISFIRE DETECTED P0301:00: CYLINDER NO.1 MISFIRE DETECTED P0302:00: CYLINDER NO.2 MISFIRE DETECTED P0303:00: CYLINDER NO.3 MISFIRE DETECTED P0304:00: CYLINDER NO.4 MISFIRE DETECTEDTHIS IS CAUSED BY IMPROPER CONTROL LOGIC OF THE PCM. IN COLD WEATHER BELOW 14 °F (-10 °C) WITH REPEATED SHORT TIME OPERATION, EXCESS FUEL INJECTED IN THE CYLINDERS MAY ACCUMULATE IN THE CRANK CASE AND RESULT IN INCREASED OIL LEVEL AND MISFIRE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMPLAIN ABOUT ONE OR BOTH OF THE FOLLOWING SYMPTOMS: WHEN SELECTING THE DEFROSTER VENTS POSITION (B) WITH THE MODE SELECTOR DIAL (A), THE DIAL DOES NOT STAY IN THE DEFROSTER VENTS POSITION AND RETURNS TO THE DEFROSTER/FLOOR VENTS POSITION (C).WHEN ROTATING THE MODE SELECTOR DIAL (A) TO THE DEFROSTER VENTS POSITION (B), IT MAY BE DIFFICULT TO TELL IF THE MODE SELECTOR DIAL IS FIRMLY IN THE DEFROSTER VENTS POSITION. THIS CONCERN MAY BE DUE TO A PRODUCTION VARIATION. SOME OF THE MODE CONTROL WIRES (A) MAY BE TOO LONG TO TRANSMIT MOVEMENT FROM THE MODE SELECTOR DIAL TO THE LINK (B). THE LENGTH OF THE MODE CONTROL WIRE HAS BEEN SHORTENED TO ELIMINATE THIS CONCERN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT ONE OF THE FOLLOWING CONCERNS: HARD TO SHIFT INTO 3RD, 4TH, 5TH, AND/OR 6TH GEAR. SOMETIMES THE SHIFTER MAY JUMP OUT OF 3RD GEAR OVER A ROAD BUMP WHEN ACCELERATING AFTER DECELERATION AT 25-40 MPH (40-65 KM/H) THIS IS CAUSED BY A FAILURE OF THE RELATED CLUTCH HUB(S). TO CORRECT THE PROBLEM OF HARD SHIFTING, THE SHAPE OF THE 3-4 AND 5-6 CLUTCH HUB HAS BEEN CHANGED. A SURFACE TREATMENT HAS NOW BEEN ADDED TO THE 3-4 CLUTCH HUB TO PREVENT 3RD GEAR FROM JUMPING OUT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
WHEN DEALING WITH CUSTOMER COMPLAINTS OF EXCESSIVE CONDENSATION AND/OR WATER WITHIN THE HEADLAMP UNIT, FIRST DETERMINE IF ALL THE BULB SOCKETS ARE PRESENT AND CORRECTLY INSTALLED. IN MOST CASES YOU WILL FIND THAT THE BULB SEAL NO. 1 (A) OR HID BULB SEAL NO. 1 (B) AND BULB SEAL NO. 2 (C) SOCKET COVERS HAVE NOT BEEN CORRECTLY INSTALLED OR ARE MISSING DUE TO IMPROPER PRIOR REPAIRS (I.E., CUSTOMER REPLACING THE HEADLAMP BULBS OR BODY SHOP NOT TRANSFERRING THEM WHEN REPLACING THE HEADLAMP UNIT(S) DUE TO A COLLISION). ANY DAMAGE CAUSED BY MISSING SOCKET COVERS, HID MODULE SEAL (D), OR MISSING BUMPER BRACKETS (E) IS NOT COVERED BY WARRANTY POLICY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE SYMPTOMS MENTIONED BELOW, WHICH CAN BE FIXED WITH THE LATEST SOFTWARE UPDATE (VERSION 10.854 OR LATER).NAVIGATION SYSTEM FREEZES.MESSAGE WAITING FOR VALID GPS SIGNAL IS SHOWN IN THE MENU BAR OF NAVIGATION DISPLAY FOR SEVERAL MINUTES.VEHICLE SYMBOL IS OFF ROAD WHILE DRIVING / WRONG POSITION OF VEHICLE ON MAP.MAP IS ROTATING WHEN VEHICLE IS PARKED OR WHILE DRIVING.NAVIGATION SCREEN DONT APPEAR AFTER DEPRESSING NAVIGATION BUTTON. THEN IT DOES NOT RECOVER BY OPERATING ACC OFF TO ON POSITION.UNEXPECTED STOPPING VOICE CONTROL MESSAGE, USUALLY WHEN STARTING THE VEHICLE.CURRENT CAR POSITION (CCP) TURNING 180 DEGREES WHEN DRIVING IN REVERSE.THE MESSAGE WAITING FOR A VALID GPS SIGNAL APPEARS.RED SCREEN WITH MESSAGE "PROBLEM WITH MAP".YELLOW SCREEN WITH MESSAGE "INSERT SD CARD".NO MAP FOUND ERROR AND SD CARD CONTAINS A MAP.SCREEN TEMPORARILY GETS STUCK AT TOMTOM LOGO (SPLASH SCREEN) FOR 2 MINUTES DURING STARTUP. AFTERWARDS, THE NAVIGATION WILL NOT START UNTIL THE IGNITION IS CYCLED.SCREEN GETS STUCK AT TOMTOM LOGO (SPLASH SCREEN) DURING STARTUP.SCREEN LOCKS UP TO A "BLACK SCREEN.VEHICLE ICON JUMPS AROUND OR VIBRATES.IF NAVIGATION BUTTON IS PRESSED DURING AUDIO SCREEN, THE SCREEN FREEZES AND THE TOUCH SCREEN BECOMES INOPERATIVE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMPLAIN THAT THE FUEL GAUGE SHOWS EMPTY AND/OR THE DISTANCE-TO-EMPTY ON THE MULTI-INFORMATION DISPLAY (MID) INDICATES 0 WITH A CERTAIN AMOUNT OF FUEL REMAINING IN THE TANK.THIS MAY BE A NORMAL OPERATION OF THE FAIL-SAFE FUNCTION:1.IF FOREIGN MATERIAL (CONTAINED IN A POOR-QUALITY FUEL) ADHERES TO THE FUEL GAUGE SENDER UNIT, THE FAIL-SAFE FUNC-TION INITIATES BY FORCING THE FUEL GAUGE AND THE DISTANCE-TO-EMPTY TO INDICATE ZERO FUEL AMOUNT.2.IMMEDIATELY AFTER THE FOREIGN MATERIAL IS DISLODGED BY SHAKING OF THE FUEL DURING DRIVING OR REFUELING, THE FUEL GAUGE WILL RETURN TO A NORMAL READING, BUT THE DISTANCE-TO-EMPTY WILL CONTINUE TO READ 0 UNTIL THE NEXT REFUEL-ING OF 3 US GALLONS (10 LITERS) OR MORE.TO CORRECT THE PROBLEM THE FOLLOWING CHANGE HAS BEEN MADE:1.THERE IS NO MASS-PRODUCTION CHANGE TO PREVENT ADHESION OF FOREIGN MATERIAL TO THE FUEL GAUGE SENDER UNIT. SO THE FACT REMAINS UNCHANGED THAT THE FUEL GAUGE AND THE DISTANCE-TO-EMPTY INDICATE ZERO FUEL AMOUNT WHEN FOREIGN MATERIAL ADHERES TO THE FUEL GAUGE SENDER UNIT, AND THE FAIL-SAFE FUNCTION INITIATES.2.TO EQUALIZE THE RECOVERY TIMING FROM THE FAIL-SAFE MODE, THE LOGIC HAS BEEN CHANGED SO THAT THE DISTANCE-TO-EMPTY RECOVERS FROM 0 TO A NORMAL READING IMMEDIATELY AFTER THE FOREIGN MATERIAL IS DISLODGED (AT THE SAME TIME AS THE FUEL GAUGE).
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMPLAIN THAT THE FUEL GAUGE SHOWS EMPTY AND/OR THE DISTANCE-TO-EMPTY ON THE MULTI-INFORMATION DISPLAY (MID) INDICATES 0 WITH A CERTAIN AMOUNT OF FUEL REMAINING IN THE TANK.THIS MAY BE A NORMAL OPERATION OF THE FAIL-SAFE FUNCTION:1.IF FOREIGN MATERIAL (CONTAINED IN A POOR-QUALITY FUEL) ADHERES TO THE FUEL GAUGE SENDER UNIT, THE FAIL-SAFE FUNC-TION INITIATES BY FORCING THE FUEL GAUGE AND THE DISTANCE-TO-EMPTY TO INDICATE ZERO FUEL AMOUNT.2.IMMEDIATELY AFTER THE FOREIGN MATERIAL IS DISLODGED BY SHAKING OF THE FUEL DURING DRIVING OR REFUELING, THE FUEL GAUGE WILL RETURN TO A NORMAL READING, BUT THE DISTANCE-TO-EMPTY WILL CONTINUE TO READ 0 UNTIL THE NEXT REFUEL-ING OF 3 US GALLONS (10 LITERS) OR MORE.TO CORRECT THE PROBLEM THE FOLLOWING CHANGE HAS BEEN MADE:1.THERE IS NO MASS-PRODUCTION CHANGE TO PREVENT ADHESION OF FOREIGN MATERIAL TO THE FUEL GAUGE SENDER UNIT. SO THE FACT REMAINS UNCHANGED THAT THE FUEL GAUGE AND THE DISTANCE-TO-EMPTY INDICATE ZERO FUEL AMOUNT WHEN FOREIGN MATERIAL ADHERES TO THE FUEL GAUGE SENDER UNIT, AND THE FAIL-SAFE FUNCTION INITIATES.2.TO EQUALIZE THE RECOVERY TIMING FROM THE FAIL-SAFE MODE, THE LOGIC HAS BEEN CHANGED SO THAT THE DISTANCE-TO-EMPTY RECOVERS FROM 0 TO A NORMAL READING IMMEDIATELY AFTER THE FOREIGN MATERIAL IS DISLODGED (AT THE SAME TIME AS THE FUEL GAUGE).
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMPLAIN THAT THE STEERING WHEEL IS OFF CENTER MORE THAN 3° EVEN WHEN DRIVING STRAIGHT ON A FLAT ROAD. FOLLOW STEERING WHEEL ALIGNMENT PROCEDURE.
Source components: STEERING: STEERING WHEEL/HANDLE BAR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE SYMPTOMS MENTIONED BELOW, WHICH CAN BE FIXED WITH THE LATEST SOFTWARE UPDATE (VERSION 10.854 OR LATER).NAVIGATION SYSTEM FREEZES.MESSAGE WAITING FOR VALID GPS SIGNAL IS SHOWN IN THE MENU BAR OF NAVIGATION DISPLAY FOR SEVERAL MINUTES.VEHICLE SYMBOL IS OFF ROAD WHILE DRIVING / WRONG POSITION OF VEHICLE ON MAP.MAP IS ROTATING WHEN VEHICLE IS PARKED OR WHILE DRIVING.NAVIGATION SCREEN DONT APPEAR AFTER DEPRESSING NAVIGATION BUTTON. THEN IT DOES NOT RECOVER BY OPERATING ACC OFF TO ON POSITION.UNEXPECTED STOPPING VOICE CONTROL MESSAGE, USUALLY WHEN STARTING THE VEHICLE.CURRENT CAR POSITION (CCP) TURNING 180 DEGREES WHEN DRIVING IN REVERSE.THE MESSAGE WAITING FOR A VALID GPS SIGNAL APPEARS.RED SCREEN WITH MESSAGE "PROBLEM WITH MAP".YELLOW SCREEN WITH MESSAGE "INSERT SD CARD".NO MAP FOUND ERROR AND SD CARD CONTAINS A MAP.SCREEN TEMPORARILY GETS STUCK AT TOMTOM LOGO (SPLASH SCREEN) FOR 2 MINUTES DURING STARTUP. AFTERWARDS, THE NAVIGATION WILL NOT START UNTIL THE IGNITION IS CYCLED.SCREEN GETS STUCK AT TOMTOM LOGO (SPLASH SCREEN) DURING STARTUP.SCREEN LOCKS UP TO A "BLACK SCREEN.VEHICLE ICON JUMPS AROUND OR VIBRATES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT A CHIRP NOISE FROM THE REAR SHOCK ABSORBERS (A) WHEN DRIVING ON A ROUGH ROAD OR PASSING OVER A SPEED BUMP. VISUAL INSPECTION OF THE SHOCK ABSORBERS SHOW NO EXTERNAL DAMAGE OR OIL LEAKAGE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMPLAIN ABOUT NO COOL AIR FROM THE VENTS WHEN THE AIR CONDITIONER (A/C) IS ON. THIS CON-CERN MAY BE CAUSED BY A/C REFRIGERANT LEAKING FROM THE EVAPORATOR. SOME DEFORMED EVAPORATOR TUBES SLIPPED THROUGH QUALITY INSPECTION AND WERE USED DURING PRODUCTION. A/C REFRIGERANT LEAKS FROM IMPROPER BRAZING AT A JOINT. TO CORRECT THE PROBLEM, THE PRODUCTION AND INSPECTION CONTROL OF THE EVAPORATOR HAVE BEEN IMPROVED.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT LOW OR NO SOUND FROM SOME (OR ALL) OF THE BOSE AUDIO SYSTEM SPEAKERS (I.E. LEFT AND RIGHT FRONT DOOR SPEAKERS, FRONT CENTER SPEAKER AND LEFT AND RIGHT D-PILLAR SPEAKERS).THE POWER AMPLIFIER, WHICH CONTROLS THE OUTPUT TO THE SPEAKERS MAY BE INOPERATIVE DUE TO THE OCCURRENCE OF PAR-ASITIC RESISTANCE IN THE CIRCUIT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE MIL ILLUMINATION WITH DTC P2610 (INSTRUMENT CLUSTER INTERNAL ENGINE OFF TIMER PERFORMANCE PROBLEM) STORED IN MEMORY AFTER ENGINE START AND ROOM FUSE 15A (A) REMOVED. NOTE:THE ODOMETER WILL DISPLAY F0-002 DURING TRANSPORT MODE (ROOM FUSE 15A REMOVED). TRANSPORT MODE IS CANCELED WHEN ROOM FUSE 15A IS INSTALLED OR THE VEHICLE ODOMETER IS MORE THAN 12.4MI (20KM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
IN SUPPORT OF SKYACTIV MANUAL TRANSMISSION MODELS, MAZDA WILL SHIP TO ALL DEALERS ONE (1) NEW SPECIAL SER-VICE TOOL (SST). THE SST WILL BE SHIPPED AUTOMATICALLY BY MAZDAS TOOL VENDOR SNAP-ON TOOLS, STARTING IN MID-OCTOBER 2014.THE FOLLOWING SST IS THE LATEST ADDITION TO THE MAZDA REQUIRED TOOL (MRT) LIST.
NHTSA source summary · Original PDF not reviewed by Recallfolio
WHILE DRIVING OVER ROUGH OR BUMPY ROADS, SOME VEHICLES MAY EXHIBIT A RATTLE NOISE FROM THE INSTRUMENT PANEL AND/OR A CREAK NOISE FROM THE A-PILLAR.RATTLE NOISE FROM INSTRUMENT PANEL:THE RATTLE NOISE MAY BE CAUSED BY LOW COWL PANEL (A) MOUNTING BOLT (B) TORQUE. CREAK NOISE FROM A-PILLAR:THIS NOISE MAY BE CAUSED BY TWO JOINED PANELS (A) SCRAPING TOGETHER AT THE A-PILLAR. THE PANEL WELD AREAS HAVE BEEN IMPROVED DURING THE MASS-PRODUCTION OF VEHICLES WITH VINS JM3KE******128359 (PRODUCED JUNE 1, 2012) OR HIGHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT BLUETOOTH® HANDS-FREE AND/OR TEXT MESSAGING RELATED CONCERNS. TO IMPROVE THE HANDLING OF BLUETOOTH® HANDS-FREE AND/OR TEXT MESSAGING CUSTOMER CONCERNS, MAZDA CRE-ATED A SPECIAL SERVICE AND PARTS EXCHANGE PROGRAM AS OF FEBRUARY 2010.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT AN INOPERATIVE SEAT WARMER (OR SEAT HEATER) ON THE DRIVER AND/OR PASSENGER SEAT. WHEN WEIGHT IS APPLIED TO THE SEAT, PART OF THE HEATER ELEMENT WIRE MAY COME OUT OF POSITION AND BECOME BENT. UNDER REPEATED STRESS, THE WIRE MAY BREAK CAUSING AN INOPERATIVE SEAT WARMER CONDITION.AN ADDITIONAL ADHESION TREATMENT HAS BEEN APPLIED TO ELIMINATE THE HEATER ELEMENT WIRE FROM COMING OUT OF THE POSITION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
IN ACCORDANCE WITH FEDERAL REGULATIONS, FOLLOW THE PROCEDURE LISTED BELOW WHEN REPLACING A SPEEDOMETER.NOTE:MAZDA VEHICLES ARE MANUFACTURED WITH TAMPER-PROOF SPEEDOMETERS.WHEN A SPEEDOMETER IS REPLACED, THE NEW SPEEDOMETER WILL READ ZERO (0) MILES.THIS PROCEDURE IS EXTREMELY IMPORTANT TO ACCURATELY REPRESENT ACTUAL VEHICLE MILEAGE.PRIOR TO SPEEDOMETER REMOVAL, COMPLETE THE INFORMATION REQUIRED ON THE SPEEDOMETER REPLACE-MENT LABEL. LABELS CAN ONLY BE ORDERED THROUGH MSTORE, NOT MDCS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT AN INOPERATIVE SEAT WARMER (OR SEAT HEATER) ON THE DRIVER AND/OR PASSENGER SEAT. WHEN WEIGHT IS APPLIED TO THE SEAT, PART OF THE HEATER ELEMENT WIRE MAY COME OUT OF POSITION AND BECOME BENT. UNDER REPEATED STRESS, THE WIRE MAY BREAK CAUSING AN INOPERATIVE SEAT WARMER CONDITION.AN ADDITIONAL ADHESION TREATMENT HAS BEEN APPLIED TO ELIMINATE THE HEATER ELEMENT WIRE FROM COMING OUT OF THE POSITION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT ONE OF THE FOLLOWING CONCERNS:HARD TO SHIFT INTO 3RD GEARSOMETIMES THE SHIFTER MAY JUMP OUT OF 3RD GEAR OVER A ROAD BUMP WHEN ACCELERATING AFTER DECELERATION AT 25-40 MPH (40-65 KM/H)THIS IS CAUSED BY THE FRICTION COEFFICIENT BETWEEN THE 3/4 CLUTCH HUB AND THE SLEEVE INCREASING. A SURFACE TREAT-MENT HAS NOW BEEN ADDED TO THE 3/4 CLUTCH HUB TO DECREASE THE FRICTION COEFFICIENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
WHEN SELECTING THE DEFROSTER VENTS POSITION (B) WITH THE MODE SELECTOR DIAL (A), SOME CUSTOMERS MAY NOTICE THE DIAL DOES NOT STAY IN THE DEFROSTER VENTS POSITION AND RETURNS TO THE DEFROSTER/FLOOR VENTS POSITION (C). THIS CONCERN MAY BE DUE TO A PRODUCTION VARIATION. SOME OF THE MODE CONTROL WIRES (A) MAY BE TOO LONG TO TRANSMIT MOVEMENT FROM THE MODE SELECTOR DIAL TO THE LINK (B). THE LENGTH OF THE MODE CONTROL WIRE HAS BEEN SHORTENED TO ELIMINATE THIS CONCERN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT A VIBRATION FROM THE DRIVER-SIDE POWER DOOR MIRROR GLASS WHEN THE VEHICLE IS DRIVEN AT HIGH SPEEDS. THIS CONCERN MAY BE DUE TO A LACK OF RIGIDITY OF THE MIRROR BASE SO THE MIRROR VIBRATES WHEN IT RECEIVES VEHICLE VIBRATION OR WIND PRESSURE.AN ADDITIONAL REINFORCEMENT HAS BEEN INSTALLED INSIDE THE DOOR TO INCREASE THE DOOR PANEL STRENGTH WHERE THE DOOR MIRROR IS MOUNTED. ALSO, THE DOOR MIRROR SHAPE HAS BEEN CHANGED. BOTH OF THESE MODIFICATIONS HAVE BEEN IMPLEMENTED TO ELIMINATE MIRROR GLASS VIBRATION CONCERNS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS SERVICE BULLETIN PROVIDES INFORMATION REGARDING THE PROPER USE OF THE DRIVERS FLOOR MAT TO AVOID ANY POTENTIAL INTERFERENCE WITH THE FOOT PEDALS. THE FOLLOWING ARE POSSIBLE CAUSES OF FLOOR MAT INTERFERENCE, WHICH CAN BE AVOIDED WITH PROPER USAGE. FLOOR MAT MOVES FORWARD DUE TO IMPROPER INSTALLATION. INAPPROPRIATE FLOOR MAT (SUCH AS AFTERMARKET, NON-FACTORY-EQUIPPED, OR NON-GENUINE) IS USED. FLOOR MAT IS STACKED ONE ON TOP OF ANOTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
MAZDA NORTH AMERICAN OPERATIONS RECEIVED MANY REQUESTS FROM OUR DEALERS ASKING US TO APPROVE ADDITIONAL ON-CAR BRAKE LATHES AS AN OPTION FOR MNAO AUTHORIZED EQUIPMENT. DUE TO YOUR FEEDBACK AND AFTER EVALUATING A FEW ON-CAR BRAKE LATHES, WE ARE PLEASED TO ANNOUNCE THAT WE HAVE ADDED THE PRO CUT ON-CAR BRAKE LATHE TO MNAO AUTHORIZED EQUIPMENT PROGRAM. THE ACCU-TURN IS STILL AN APPROVED BRAKE LATHE BUT IT IS NO LONGER AVAILABLE FOR PURCHASE FROM OUR VENDOR. IMPORTANT REMINDER ROTORS MUST BE MACHINED USING A MAZDA APPROVED ON-CAR BRAKE LATHE OR WARRANTY CLAIMS ARE SUBJECT TO DENIAL OR DEBIT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY EXPERIENCE AN ELECTRICAL MALFUNCTION AFTER A VEHICLE BODY REPAIR. THE NEWLY PAINTED FENDER STAY (B) MAY BE CAUSING A POOR FRONT HARNESS (A) GROUND CONNECTION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMPLAIN THAT THE AMBIENT TEMPERATURE DISPLAY IS NOT ACCURATE, OR IT TAKES TOO LONG FOR THE DISPLAY TO SHOW ACTUAL TEMPERATURE.WHEN YOU ENCOUNTER A CUSTOMER WITH THIS CONCERN, FIRST VERIFY THE CONDITION WHEN THE CUSTOMER NOTICED THIS SYMPTOM. IF THE CONDITION IS SIMILAR TO THE FOLLOWING CONTROL LOGIC OF AMBIENT TEMPERATURE OR DIF-FERENCE BETWEEN THE TEMPERATURE DISPLAY AND OTHERS, ADVISE THE CUSTOMER THAT THIS IS A NOR-MAL CHARACTERISTIC OF THE VEHICLE AND NOT A MALFUNCTION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES EXHIBIT BRAKE RELATED CONCERNS SUCH AS BRAKE NOISE, BRAKE JUDDER OR BRAKE DRAGGING. IF YOU ENCOUNTER A CUSTOMER COMPLAINT FOR ANY ONE OF THESE SYMPTOMS, REFER TO THE FOLLOWING INFORMATION TO UNDERSTAND WHY SYMPTOMS MAY OCCUR, AND TO BETTER ASSIST THE CUSTOMER IN RESOLVING THEIR SPECIFIC BRAKE CONCERN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH DTC P0842, P0847, P0872 AND/OR P0877 STORED IN THE TCM MEMORY.P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ONP0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ONP0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ONP0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ONTHE DTC P0780 AND/OR P1738 MAY ALSO BE STORED TOGETHER.P0780:00 - GEAR SHIFTING MALFUNCTIONP1738:00 - AUTOMATIC TRANSAXLE INTERNAL MALFUNCTION. NOTE: THIS SERVICE INFORMATION IS ALSO APPLICABLE IF DTC P0780:00 IS STOREED INDEPENDENTLY. THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO CORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE SYMPTOMS MENTIONED BELOW, WHICH CAN BE FIXED WITH THE LATEST SOFTWARE UPDATE (VERSION 10.852 OR LATER). VEHICLE ICON JUMPS AROUND OR VIBRATES. CAUTION: DO NOT USE THE FACTORY RESET FOR RETAIL VEHICLES. OTHERWISE, PERSONAL SETTINGS (SUCH AS DISPLAY AND SOUND ADJUSTMENTS) WILL BE LOST, INCLUDING FAVORITES INFORMATION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH DTC P0842, P0847, P0872 AND/OR P0877 STORED IN THE TCM MEMORY.P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ONP0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ONP0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ONP0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ONTHE DTC P0780 AND/OR P1738 MAY ALSO BE STORED TOGETHER.P0780:00 - GEAR SHIFTING MALFUNCTIONP1738:00 - AUTOMATIC TRANSAXLE INTERNAL MALFUNCTIONTHIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO CORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH DTC P0842, P0847, P0872 AND/OR P0877 STORED IN THE TCM MEMORY.P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ONP0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ONP0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ONP0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ONTHE DTC P0780 AND/OR P1738 MAY ALSO BE STORED TOGETHER.P0780:00 - GEAR SHIFTING MALFUNCTIONP1738:00 - AUTOMATIC TRANSAXLE INTERNAL MALFUNCTIONTHIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO CORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE SYMPTOMS MENTIONED BELOW, WHICH CAN BE FIXED WITH THE LATEST SOFTWARE UPDATE (VERSION 10.852 OR LATER). VEHICLE ICON JUMPS AROUND OR VIBRATES. CAUTION: DO NOT USE THE FACTORY RESET FOR RETAIL VEHICLES. OTHERWISE, PERSONAL SETTINGS (SUCH AS DISPLAY AND SOUND ADJUSTMENTS) WILL BE LOST, INCLUDING FAVORITES INFORMATION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXHIBIT A CONDITION WHERE THE CHECK ENGINE LIGHT ILLUMINATES IMMEDIATELY AFTER THE ENGINE IS STARTED AND DTC P0452:00 AND/OR P0453:00 IS STORED IN MEMORY. P0452:00 - FUEL TANK PRESSURE SENSOR LOW INPUTP0453:00 - FUEL TANK PRESSURE SENSOR HIGH INPUTTHIS CONCERN MAY BE CAUSED BY ANTS ENTERING THE FTP SENSOR THROUGH AN OPENING (TO ATMOSPHERE). THE ANTS BITE AND EVENTUALLY DAMAGE THE WIRING, WHICH RESULTS IN AN IMPROPER FTP SENSOR OUTPUT. TO ELIMINATE THIS CONCERN, THE INSIDE OF THE OPENING PIPE (TO ATMOSPHERE) HAS BEEN MODIFIED TO PREVENT ANTS FROM ENTERING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH DTC P0842, P0847, P0872 AND/OR P0877 STORED IN THE TCM MEMORY. P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ON THE DTC P0780 AND/OR P1738 MAY ALSO BE STORED TOGETHER. P0780:00 - GEAR SHIFTING MALFUNCTION P1738:00 - AUTOMATIC TRANSAXLE INTERNAL MALFUNCTION THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO CORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH DTC P0842, P0847, P0872 AND/OR P0877 STORED IN THE TCM MEMORY. P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ON THE DTC P0780 AND/OR P1738 MAY ALSO BE STORED TOGETHER. P0780:00 - GEAR SHIFTING MALFUNCTION P1738:00 - AUTOMATIC TRANSAXLE INTERNAL MALFUNCTION THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO CORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMPLAIN ABOUT ONE OF THE FOLLOWING SYMPTOMS WHEN THE VEHICLE IS STOPPED AND THE TRANSMISSION IS IN D RANGE: AN INTERMITTENT HIGH ENGINE IDLE SPEED. AN INTERMITTENT ENGAGEMENT SHOCK. AN INTERMITTENT FORWARD LURCH. THESE CONDITIONS MAY OCCUR WHEN THE CUSTOMER DEPRESSES THE BRAKE PEDAL AND MAKES CONTACT WITH THE THROTTLE PEDAL SIMULTANEOUSLY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
THE NAVIGATION SYSTEM SUPPORT FOR DIAGNOSTICS, PARTS AUTHORIZATION, AND PARTS EXCHANGE REQUIRE CONTACTING THE PROPER SOURCE. TOMTOM NAVIGATION HELP DESK AT 866-486-6866 FROM 7AM-11PM (M-F) AND 9AM-8PM (SAT) EASTERN STANDARD TIME. NOTE: ONE OF THE FIRST STEPS FOR TROUBLESHOOTING THE NAVIGATION SYSTEM IS FOR THE CUSTOMER OR DEALER TO CALL TOMTOM. IF THE TOMTOM CALL CENTER CANNOT SOLVE THE CUSTOMERS PROBLEM, THEY WILL PROVIDE A CASE NUMBER TO THE CUSTOMER THAT CAN BE REFERRED TO IF NEEDED. SERVICE ADVISORS SHOULD GET THIS CASE NUMBER FROM THE CUSTOMER IF THE VEHICLE COMES INTO THE DEALER FOR FURTHER DIAGNOSIS SO THE TECHNICIAN CAN HAVE IT WHEN CALLING TOMTOM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME CUSTOMERS MAY COMPLAIN OF CONDENSATION/FOG INSIDE THE FRONT OR REAR COMBINATION LIGHTS. THE RECENT NEW MODELS HAVE BEEN FITTED WITH A CLEAR LENS WHICH CAN CAUSE THE SYMPTOM TO BE MORE NOTICEABLE, HOWEVER, IT DOES NOT AFFECT THE PERFORMANCE OF THE LIGHT. THIS CONDENSATION/FOG IS A NATURAL PHENOMENON THAT OCCURS WHEN THERE IS A FAIRLY LARGE TEMPERATURE DIFFERENCE BETWEEN THE INSIDE AND THE OUTSIDE OF THE LIGHT HOUSING. IT IS NORMAL FOR VERY SMALL WATER DROPS TO APPEAR IN CERTAIN LOCATIONS ON THE LIGHT UNITS WHERE THE AIR IS STAGNANT (CONDENSATION), MAKING THE LENS LOOK WHITISH (FOG). THIS HAPPENS MOSTLY IN THE CORNERS AND NARROW SPACES, AND WILL TYPICALLY CLEAR DURING WARMER AMBIENT TEMPERATURES, OR WHEN THE LIGHTS HAVE BEEN ON FOR SOME TIME. EXPLAIN TO THE CUSTOMER THAT THIS IS A NATURAL PHENOMENON AND NOT A QUALITY DEFECT. DO NOT ATTEMPT REPAIRS AS THIS IS CONSIDERED NORMAL, AND IS NOT COVERED UNDER WARRANTY. REPLACING THE LIGHT UNIT WILL NOT CORRECT THIS SYMPTOM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME VEHICLES MAY EXPERIENCE STAINS APPEARING ON THE HOOD, ROOF AND/OR TRUNK OF THE VEHICLE. THIS CONCERN IS MOST LIKELY TO BE FOUND IN A COLD WEATHER AREAS JUST AFTER THE RAPGARD IS REMOVED AT PDI. THIS MAY BE CAUSED BY MOISTURE WHICH HAS BEEN TRAPPED AND CONDENSED BETWEEN THE PAINT AND THE RAPGARD. THESE TYPES OF STAINS CAN BE REMOVED WITH A HEAT GUN OR AN INFRARED DRIER.IF YOU ENCOUNTER THIS CONCERN DURING PDI, USE A HEAT GUN OR AN INFRARED DRIER TO APPLY HEAT TO THE AFFECTED AREA TO REMOVE THE STAIN(S).