2017 Lincoln MKC Manufacturer communications & TSBs.Page 1
Original record summaries, dates and identifiers for this model-year. Records 1–100 of 164, ordered newest first. Dated records on this page: Feb 14, 2018–May 9, 2026.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
May 9, 2026Other
25B51
NHTSA communication ID: 11033577
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2021-2024 Model Year Bronco, 2021-2024 Model Year Bronco Sport, 2020-2022 Model Year Corsair and Escape, 2016-2024 Model Year Explorer, 2019-2020 Model Year Fusion, 2016-2018 Model Year Focus RS, 2022-2024 Model Year Maverick, 2016-2019 Model Year MKC and 2019-2024 Model Year Ranger Vehicles Equipped with a 2.0L or 2.3L Engine and Engine Block Heater System Block Heater Replacement
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customer Satisfaction Program 25N15 - Supplement #1 Certain 2015-2019 Model Year Multiple Vehicle Lines Rear View Camera Inspection For One-Time Replacement
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 24-2165 to update the TSB Service Procedure. Some vehicles listed in the Model statement above may exhibit various SYNC performance related concerns including but not limited to: Display operation concerns Navigation inoperative Voice recognition concerns Phone connection issues Dropped phone connections Applink related performance Travel Link not present or showing incorrect traffic Slow system response NOTE: Ford has found some of the APIMs replaced and returned for inspection contained an outdated software level and the APIM did not require replacement. The customer concern may have been resolved by updating the APIM with latest level of software. The SYNC 3 universal thumb drive will be able to update the APIM software without the use of a scan tool and does not require the process to be monitored. Ford will be monitoring APIM replacements to confirm TSB directed software updates have been performed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. Pinpoint test HK in the Powertrain Control and Emissions Diagnosis (PC/ED) or in Section 303-14 of the Workshop Manual (WSM) has been updated to address this concern.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: • Customer concern of a vibration or rough idle in D or R • Shudder while driving • Lack of engine RPM • Low performance, lack of acceleration on take off"
NHTSA source summary · Original PDF not reviewed by Recallfolio
While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions. While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 21-2175 to update the TSB Service Procedure. Some 2016 MKS, 2016-2017 Navigator, 2016-2018 F-150/Focus/C-MAX/Edge/Fiesta/MKX/Transit Connect/Mustang, 2017-2018 Continental/Fusion/MKZ, 2017-2019 Explorer, 2016-2019 Escape/MKC/Flex/MKT/Taurus/Transit/Expedition/F-Super Duty, and 2018-2019 EcoSport vehicles equipped with SYNC 3 may experience various SYNC performance related concerns. related concerns including but not limited to: Display operation concerns Navigation inoperative Voice recognition concerns Phone connection issues Dropped phone connections Applink related performance Travel Link not present or showing incorrect traffic Slow system response This may be due to the SYNC software. To correct the condition, follow the Service Procedure to update the accessory protocol interface module (APIM) software. NOTE: Ford has found some of the APIMs replaced and returned for inspection contained an outdated software level and the APIM did not require replacement. The customer concern may have been resolved by updating the APIM with latest level of software.
NHTSA source summary · Original PDF not reviewed by Recallfolio
For 2015-2024 Ford and Lincoln vehicles equipped with turbocharged engines and customer concern of an engine oil leak, refer to Workshop Manual (WSM), Section 303-00 for oil leak inspection and testing methods. Ford has evaluated turbochargers replaced for oil leak symptoms and although oil may collect on the external surface of a turbocharger, it is extremely rare for a turbocharger assembly to be the root cause of the oil leak. Careful inspection of the turbocharger oil feed and drain tubes should be performed along with the recommended WSM procedures as needed. Warranty claims for turbocharger replacement going forward will be assessed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2014-2020 Model Year Multiple Vehicle Lines 3G Telematics Control Unit to 4G Upgrade Kit REASON FOR THIS SUPPLEMENT Program Terms & Urgency / Expiration Date: Program extension until July 31, 2023. Service Action: o IDS level 128 or higher is now required to address various programming issues encountered. o C-MAX Energi vehicles are now serviceable with new software and hardware. Labor Allowances: C-MAX labor has been updated. Parts Requirements / Ordering Information: o The C-MAX 4G Upgrade Kit is now orderable at this time with a new part number. o MKX Rear seat backrest nut claim quantity updated. Technical Information updates: o Ensure IDS level 128 or higher is used. o Toggling Valet Mode is no longer required. o C-MAX Energi instructions are now available. Owner Notification: Non-repaired vehicle owners will be mailed the week of April 17, 2023. Pickup and Delivery: Added Customer Acknowledgement Form - Review form contents with customer prior to kit ordering and obtain customer signature prior to installation for Focus BEV, C-MAX, and Fusion Energi vehicles.
NHTSA source summary · Original PDF not reviewed by Recallfolio
For 2000-2024 Ford and Lincoln vehicles, swapping a module from a vehicle for diagnosis purposes is likely to cause errors and is not recommended. It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2015-2019 MKC and 2016-2019 Explorer Vehicles Equipped With the 2.3L Engine and 6F35 Transmission - Transmission Extended Warranty Coverage Updated Owner Letters: 20N07/20B27 S1
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2015-2019 MKC and 2016-2019 Explorer Vehicles Equipped With the 2.3L Engine and 6F35 Transmission Powertrain Control Module Reprogram Submitting Owner Letters
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2015-2019 MKC and 2016-2019 Explorer vehicles equipped with the 2.3L engine and 6F35 transmission; Powertrain Control Module reprogram. Supplement: Program terms will be in effect through August 31, 2023 This program is now eligible for mobile repairs
Source components: POWER TRAIN · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM) · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE:SOFTWARE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2017 C-MAX Energi, 2013-2018 Focus battery electric vehicle (BEV), 2013-2020 Fusion plug-in hybrid electric vehicle (PHEV), 2015-2017 MKZ/MKZ Hybrid/MKC, 2016-2017 MKX and 2017 Continental vehicles equipped with 8 inch or larger center display screen may be unable to complete modem authorization after 3G to 4G modem upgrade was performed. No Authorization Pop-up will be displayed on the center display screen during the Authorization process. The vehicle may also not have proper functionality of remote app features such as remote start, return odometer, fuel information, or vehicle location incorrect in the app. This may be due to the SYNC software. To correct the condition, follow the Service Procedure to toggle Valet Mode.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2022 Ford/Lincoln customers may experience a notification in the FordPassÃÂÃÂÃÂî/LincolnWayÃÂÃÂÃÂî app indicating Vehicle Has Entered Deep Sleep Mode. This occurs when the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SOC) drops below 50%. A warning may also set if the telematic control unit (TCU) has received an over the air update. The TCU powers down all communication when in this mode and app features are disabled. Manually start the vehicle to wake if from mode. More information is located in the app under: Account > Help > search 'Deep Sleep' in the entry box. If the condition remains, check the BCM 12v SOC. If the SOC does not change after charging the battery or after BMS reset is performed, continue with normal battery and/or BMS sensor diagnostics.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2014-2020 Model Year Multiple Vehicle Lines - 3G Telematics Control Unit to 4G Upgrade Kit. The North America 3G cellular service began decommissioning in August 2021 and a complete shutdown of the 3G network took place in February 2022. Vehicles on the road equipped with a 3G telematics control unit (TCU) / embedded modem will lose mobile app functionality/connectivity.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2019 MKC and 2016-2019 Explorer vehicles equipped with a 2.3L engine may exhibit a vibration/rough idle when the vehicle is in drive (D) or reverse (R). The vehicle may also exhibit a lack of engine revolutions per minute (RPM), lack of acceleration on take off and/or shudder while driving. This may be due to the torque converter overheating causing damage to the torque converter as well as possible internal damage to the transmission. To correct this condition, follow the Service Procedure to replace the torque converter and specified internal transmission components that may have been damaged.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2017 C-MAX Energi, 2013-2018 Focus battery electric vehicle (BEV), 2013-2020 Fusion plug-in hybrid electric vehicle (PHEV), 2015-2017 MKZ/MKZ Hybrid/MKC, 2016-2017 MKX and 2017 Continental vehicles equipped with SYNC screens 8 inch or larger may be unable to complete modem authorization after 3G to 4G modem upgrade was performed. No Authorization Popup will be displayed on SYNC infotainment screen during the Authorization process. The vehicle may also not have proper functionality of remote app features such as remote start, and return odometer and fuel information to the app. This may be due to the SYNC software. To correct the condition, follow the Service Procedure to toggle Valet Mode.
Source components: ELECTRICAL SYSTEM:PROPULSION SYSTEM:HYBRID MANAGEMENT:POWER CONTROL UNIT/MODULE (HPCU):SOFTWARE · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 Edge and 2017-2019 Fusion/MKZ/Escape/MKC vehicles equipped with a 2.0L EcoBoost engine may exhibit a low coolant level, white exhaust smoke and/or a runs rough condition with or without an illuminated malfunction indicator lamp (MIL). Diagnostic trouble codes (DTCs) may include P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To correct the condition, follow the Service Procedure to replace the long block engine assembly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2023 Ford or Lincoln vehicles with modems activated through FordPass or LincolnWay may experience 12 volt battery drain symptoms when the customer uses non-Ford/Lincoln phone applications as an alternate channel to access vehicle commands such as door lock/unlock, remote start, vehicle location, etc. The battery drain may be caused by excessive calls for data through the vehicle network keeping it in an activated state. Recommend that the customer uninstall the app to ensure this is not contributing to battery symptoms experienced. Advise the customer that unaffiliated third-party app developers do not work directly with Ford to adhere to security, vehicle communication, and privacy requirements.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2014-2017 C-MAX Energi, 2014-2020 Fusion plug-in hybrid electric vehicle (PHEV), 2015-2017 MKZ/MKZ Hybrid/MKC, 2016-2017 MKX, 2016-2018 Focus battery electric vehicle (BEV) and 2017 Continental vehicles equipped with SYNC screens 8 inch or larger may be unable to complete modem authorization after 3G to 4G modem upgrade was performed. No Authorization Popup displayed on SYNC infotainment screen during the Authorization process. This may be due to the Sync Software. To correct the condition, follow the Service Procedure to toggle Valet Mode.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 Edge and 2017-2019 Fusion/MKZ/Escape/MKC vehicles equipped with a 2.0L EcoBoost engine may exhibit a low coolant level, white exhaust smoke and/or a runs rough condition with or without an illuminated malfunction indicator lamp (MIL). Diagnostic trouble codes (DTCs) may include P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To correct the condition, follow the Service Procedure steps to replace the long block engine assembly.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 21-2236 to update the models and year affected. Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2013-2022 Escape, 2015-2018 Focus, 2015-2019 MKC, 2015-2022 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2022 F-Super Duty, 2018-2022 EcoSport/Expedition, 2019-2022 Ranger/Nautilus, 2021-2022 Bronco/Bronco Sport/Mustang Mach-E, 2022 Maverick vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2018 Focus/MKX/C-MAX, 2017-2019 MKC/Taurus/Flex/MKT, 2017-2020 Fusion/MKZ/Continental, 2017-2022 Mustang/Edge/Explorer/Police Interceptor Utility/Escape/F-150/F-Super Duty, 2018-2022 Expedition/Navigator, 2019-2022 Ranger/Nautilus, 2020-2022 Corsair/Aviator, and 2021-2022 Mustang Mach-E vehicles may exhibit a noisy, incorrectly operating, and/or inoperative seat motor. This may be due to a damaged or inoperative seat track motor. A lower level service part has been released to correct noisy, incorrect operation/inoperative seat track motors.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2020 Fusion/MKZ and 2017-2019 Escape/MKC vehicles equipped with a 2.0L EcoBoost engine may require replacement of the long block engine assembly. New service kits have been released which include all the one-time-use components required in the service procedure for removal and replacement of the long block engine assembly. Refer to the Ford Electronic Parts Catalog (ECAT) for long block service kit part number by application.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2021 Ford and Lincoln vehicles equipped with SYNC 3 may exhibit a condition where the navigation voice prompts are inoperative after a SYNC map update. This may be due to an incomplete installation of the SYNC map software. If possible, using the original USB that installed the update, reperform the update and verify the navigation voice prompts have returned. Multiple reboots are expected when this update is being performed. Verify the Installation Is Complete message displays in the touch screen. If the original USB is not available, go to website https://syncnavigation.com/ford/home or https://syncnavigation.com/lincoln/home to download the files once more for the affected vehicle. For further map update support, reference the FAQ section on these websites.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various 2014-2020 vehicles equipped with a 3G modem may experience a lack of 3G modem performance. This may be due to the 3G cellular service functionality being decommissioned starting August 2021 and through March 2022. As the 3G cellular service is decommissioned, vehicles equipped with the 3G telematics control unit (TCU) will lose MyFord Mobile and MyLincoln Mobile app functionality/connectivity. Repair or Replacement of the TCU should no longer be performed using existing service stock. Replacement of the 3G TCU for this concern will result in programming concerns and repairs should not be performed. The customer can pay to upgrade their 3G modem with a 4G modem by following the information in FSA 21B09. Refer to FSA 21B09 for reference and not for claiming.
Source components: COMMUNICATION:MANUFACTURER TELEMATICS · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2014-2020 Model Year Multiple Vehicle Lines 3G Telematics Control Unit to 4G Upgrade Kit The North America 3G cellular service began decommissioning in August 2021 and will be fully decommissioned in February 2022. Vehicles on the road equipped with a 3G telematics control unit (TCU) / embedded modem will lose mobile app functionality/connectivity. Some owners are still within the *complimentary trial period (depending on model year and brand, see table below) for connected services.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2017 Ford and Lincoln vehicles with a new body control module (BCM) installed may exhibit a programming error when using IDS versions 122.03 through 123.01 stating 'Data Corrupt' or 'Configuration Failed, would you like to retry?'. IDS scan tool version 123.02 contains a fix for this programming error. Install IDS version 123.02 or later from PTS > Rotunda tab > Diagnostic Tool Support > Download Software. Once installed, perform the BCM programmable module installation (PMI). Refer to Workshop Manual (WSM), Section 419-10 > Removal and Installation.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:BODY CONTROL MODULE/BCM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK12 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2021 Ford or Lincoln vehicles equipped with SYNC 3 or SYNC 4 may exhibit a blank screen or other various SYNC symptoms only when the vehicle is in transport mode. This is considered normal due to the power saving features enabled while in transport mode. It is beneficial for battery life to keep the vehicle in transport mode until the vehicle is prepped for sale. To prevent a SYNC system lockup during transport mode deactivation, follow the Workshop Manual (WSM) procedure exactly allowing time for the SYNC system to complete its tasks such as fully booting up or powering down and shutting off before moving to the next step of the procedure. If the vehicle exhibits a blank screen or SYNC symptoms after transport mode deactivation, refer to WSM, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2013-2021 Escape, 2015-2018 Focus, 2015-2019 MKC, 2015-2021 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2021 F-Super Duty, 2018-2021 EcoSport/Expedition, 2019-2021 Ranger/Nautilus, 2021 Bronco Sport/Mustang Mach-E vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2019 Escape/MKC Some 2017-2019 Escape/MKC vehicles equipped with all-wheel drive (AWD) may exhibit a binding/shudder and/or bump/clunk from the rear drive unit (RDU) when turning at low speeds and parking lot maneuvers. This may be due to the software in the powertrain control module (PCM). To correct the condition, follow the Service Procedure to reprogram the PCM. T
NHTSA source summary · Original PDF not reviewed by Recallfolio
This program extends the warranty coverage of the automatic transmission torque converter for twelve (12) months from the RO date of Powertrain Control Module reflash under Customer Satisfaction Program 20B27.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2019 MKC and 2016-2019 Explorer vehicles equipped with a 2.3L engine may exhibit a vibration/rough idle when the vehicle is in DRIVE or REVERSE. The vehicle may also exhibit a lack of engine revolutions per minute (RPM), lack of acceleration on take off and/or shudder while driving. This may be due to the torque converter overheating causing damage to the torque converter as well as possible internal damage to the transmission. To correct this condition, follow the Service Procedure steps to replace the torque converter and specified internal transmission components that may have been damaged.
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
In some of the affected vehicles, customers may experience adverse NVH, vibration and/or rough idle in Drive or Reverse, low performance/lack of acceleration during launch, sluggish vehicle operation and shudder while driving
Source components: EQUIPMENT ADAPTIVE/MOBILITY · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
In some of the affected vehicles, customers may experience adverse NVH, vibration and/or rough idle in Drive or Reverse, low performance / lack of acceleration during launch, sluggish vehicle operation and shudder while driving.
NHTSA source summary · Original PDF not reviewed by Recallfolio
In affected vehicles, the transmission torque converter may overheat in certain driving conditions. If the torque converter overheats it can lead to adverse NVH, rough idle, and low performance concerns. Ultimately this will require internal transmission repairs to resolve the concern. Ford Motor Company has developed and update to the Powertrain Control Module software that helps protect the transmission torque converter from overheating when exposed to certain driving styles.
Source components: ELECTRICAL SYSTEM:SOFTWARE · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2009-2020 Ford and Lincoln vehicles equipped with turbochargers may exhibit an oil leak from the turbocharger oil supply or return tubes, O-rings or 6.7L pedestal gasket. Although oil may collect on the turbocharger, it is very rare for a turbocharger to leak oil. To isolate the source of the leak, refer to Workshop Manual (WSM), Section 303-00 General Information > Diagnosis and Testing > Engine > Engine Oil Leaks - Fluorescent Oil Additive Method procedure. When an oil leak is present at a turbocharger oil supply or drain tube, remove the affected oil tube and inspect for damage, and replace the O-ring seals, pedestal gasket or oil tube as required. Refer to WSM, Section 303-04. For claiming, use the affected oil tube or pedestal gasket as the causal part and applicable labor operations in Sections 6 and 9 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016 MKS, 2016-2017 Navigator, 2016-2018 F150/Focus/CMAX/Edge/Fiesta/MKX/ Transit Connect/Mustang, 2017-2018 Continental/Fusion/MKZ, 2017-2019 Explorer, 2016-2019 Escape/MKC/Flex/MKT/Taurus/Transit/Expedition/F-Super Duty, and 2018-2019 EcoSport vehicles equipped with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2020 Ford and Lincoln vehicles equipped with a SYNC 3 Touchscreen may experience the volume control unresponsive from the Front Control Interface Module (FCIM) and steering volume controls when using Apple Car Play. When the Apple device is removed, volume control is restored. This is due to a concern with the Waze Navigation App software and Apple iOS version. To correct the condition, update the Waze App software and iOS to the latest version available and reboot the customer's Apple device. Perform an ignition cycle and reconnect the Apple device via USB. Open Apple Car Play and confirm volume control is restored. Installing/Updating third party software/applications is not warrantable.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2012-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit an inoperative remote start with a 'Vehicle Failed To Start' message when using MyFord Mobile/Ford Pass/Lincoln Way mobile applications. The cellular cloud systems will only allow two remote start requests from the MyFord Mobile/Ford Pass/Lincoln Way apps without a vehicle drive event occurring. If a third remote start request is received, a Vehicle Failed To Start message will be displayed quickly in the mobile app. Once the vehicle is driven, the remote start counter is reset and will allow remote start commands to be sent from the mobile app. If the remote start system is not functioning using the key fob, refer to Workshop Manual (WSM) Section 303-06 for further diagnosis.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2018 C-Max, 2013-2020 Escape/Fusion/MKZ, 2015-2018 Focus,2015-2019 MKC, 2015-2020 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2020 F-Super Duty, 2018-2020 EcoSport/Expedition, 2019-2020 Ranger/Nautilus vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
Source components: SEATS · STRUCTURE:FRAME AND MEMBERS:UNDERBODY SHIELDS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may experience a notification in the FordPass and/or LincolnWay apps that indicates their vehicle has entered "deep sleep mode". This mode is enabled due to the vehicle not being started for 14 consecutive days or battery voltage is at/or below 9.5 volts. Some 2020 models will also set a warning if the telematic control unit (TCU) has received an automatic over the air update. The purpose of deep sleep mode is to conserve battery voltage. When deep sleep mode is enabled, the TCU is powered down and all communication with the FordPass and/or LincolnWay apps are disabled. To wake the vehicle from deep sleep mode, manually start the vehicle. More deep sleep mode information can be found in the FordPass or LincolnWay apps under: More > Guides > click in search entry box > type "deep sleep" and click on "Ask".
NHTSA source summary · Original PDF not reviewed by Recallfolio
SSM 48619 - Various Vehicles - Perimeter Alarm Armed And Original Vehicle Keys Cannot Be Accessed to Enter Vehicle - CAN Protection Strategy Some 2013-2016 Model Year Vehicles may exhibit a concern in which the Perimeter Alarm is active and the original keys cannot be accessed to disable the perimeter alarm. This concern would most often occur when a customer loses keys and the dealership is attempting to program new keys to the vehicle. The Workshop Manual (WSM), Section 419-01A Perimeter Anti-Theft Alarm - System Operation and Component Description has been updated to inform of the Controller Area Network (CAN) Protection Strategy. Follow the procedure outlined to prevent replacement of the Body Control Module (BCM) on CAN Protection Strategy equipped vehicles when original keys are lost and perimeter alarm is active. Refer to the WSM for further detail on the CAN Protection Strategy. Lost keys and replacement of BCM for lost keys is non-warrantable.
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2020 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 Edge and 2017-2019 Fusion/MKZ/Escape/MKC vehicles equipped with a 2.0L EcoBoost engine may exhibit a low coolant level, white exhaust smoke and/or a runs rough condition with or without an illuminated malfunction indicator lamp (MIL). Diagnostic trouble codes (DTCs) may include P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To correct the condition, follow the Service Procedure steps to replace the long block engine assembly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2019 vehicles equipped with SYNC 3 may experience a map displayed on the left half of the SYNC screen with no other information/soft buttons present after updating to the latest version of V3.0 software. This issue occurs when the SYNC 3 system has been previously modified using an aftermarket device to display the Ford GT welcome screen/HMI Theme. To correct this issue, please contact the Technical Hotline Assistance Center to have the vehicle restored back to its original state.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2020 vehicles equipped with an EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function. To support the proper diagnosis of this compressor, the EVDC control valve tester has been provided to each U.S. dealership (339-EVDC100). Ensure the A/C system has a full charge prior to any compressor diagnostics. To support the proper diagnosis of this compressor, the EVDC compressor tool must be used, and the results recorded in the Technician comments field with the warranty claim. This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2010-2020 vehicles may exhibit distorted glass with a subtle orange peel pattern or streaking etched into the surface. This is caused by hydrofluoric acid which is used in some car wash solutions as a cleaning agent. Hydrofluoric acid can attack the glass and cause visual distortion and/or discoloration on the outer surface which cannot be removed by further cleaning. If this type of distortion is found, inspect the area of the glass that is covered by the cowl and/or molding. The portion of glass that is covered by the cowl or molding will not be affected by the acid. Hydrofluoric acid damage is not a defect in material or workmanship and is not a warrantable condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
For Ford and Lincoln vehicles that require positive or negative battery terminal replacement, it is not necessary to replace the complete battery cable harness (14300 and 14301) for this concern. Positive battery cable clamp BT4Z-14450-AA and negative battery cable clamp BT4Z-14450-BA are available for this type of repair. Do not cut or shorten the battery cable, instead carefully remove the affected battery cable clamp and clean the cable end as necessary to preserve wire length. Some rework may be necessary for some vehicle environments. Bend the new positive battery cable clamp as needed and crimp it to the existing battery cable. Make sure to use heat shrink tubing over the battery cable to battery cable clamp connection. Obtain the heat shrink tube locally.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2019 vehicles may experience a no crank concern due to a security access key table error. When attempting to program keys or perform a parameter reset, the procedure may fail and the appropriate Ford diagnostic scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the body control module (BCM) is internally damaged and requires replacement. The BCM should only be replaced for this condition when the 232 key table error message is present. If the 232 key table error is not present, follow normal diagnostics for the no crank condition. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 Edge and 2017-2019 Fusion/MKZ/Escape/MKC vehicles equipped with a 2.0L EcoBoost engine may exhibit a low coolant level, white exhaust smoke and/or a runs rough condition with or without an illuminated malfunction indicator lamp (MIL). Diagnostic trouble codes (DTCs) may include P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To correct the condition, follow the Service Procedure steps to replace the long block engine assembly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2019 Ford and Lincoln vehicles equipped with SYNC 3 not at the latest software level may exhibit Various Performance Related concerns such as Display Operation, Navigation, Voice Recognition, Phone Pairing, Applink, Travel Link, Slow System Response, etc. Check for SYNC software update under the OASIS Tab SYNC selection. If an update is available refer to WSM,Section 415-00 and update the APIM software. After Installation, complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual. Section
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2017 F-150/Mustang, 2015-2018 Edge/MKC, 2016-2018 MKX, 2013-2018 Explorer/Taurus/Flex/MKT, and 2017-2018 Fusion/MKZ/Continental vehicles built on or before 19-Oct-2017 may exhibit an inoperative adaptive cruise control, collision warning, and/or collision avoidance system with a Pre-Collision Assist Not Available, Collision Warning Not Available, and/or Adaptive Cruise Fault message present in the instrument panel cluster (IPC) and diagnostic trouble code (DTC) U3000:49 present in the cruise control module (CCM). To resolve the condition, reprogram the CCM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 9E731 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 Edge and 2015-2019 Fusion/MKZ/Escape/MKC vehicles equipped with a 2.0L EcoBoost engine may exhibit a low coolant level, white exhaust smoke and/or a runs rough condition with or without an illuminated malfunction indicator lamp (MIL). Diagnostic trouble codes (DTCs) may include P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To correct the condition, follow the Service Procedure steps to replace the long block engine assembly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2019 Escape/MKC vehicles equipped with a 1.5, 2.0L or 2.3L EcoBoost engines may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P04F0 and/or P144C stored in the powertrain control module (PCM). This may be due to loose or partially connected evaporative emissions (EVAP) vapor lines. Before completing the Powertrain Control/Emissions Diagnosis (PC/ED) Manual pinpoint test (PPT) follow the Service Procedure steps on vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2019 MKC vehicles built on or before 01-Apr-2019 may exhibit an air conditioning (A/C) system with a difference in the discharge temperature between the left and right vents. The left vent discharge temperature will usually be warmer than the right vent discharge temperature. Reprogram the front controls interface module (FCIM) using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 18842 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
On vehicles equipped with an automatic transmission it is imperative that the converter pilot hub be greased with Motorcraft Multi-Purpose Grease Spray XL-5-A even if grease was not applied from the factory. Also verify that the engine/transmission alignment dowel pins are present as well as the engine crankshaft dowel pin, if equipped, when installing the transmission. Failure to adequately lubricate the converter hub greatly increases the likelihood of the flexplate cracking in the future. Missing dowels may cause a misalignment issue also resulting in a premature failure. Refer to Workshop Manual (WSM), Section 307-01.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2019 vehicles equipped with a EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SSM 47948 - 2010-2019 Various Vehicles - Turbocharged Engines - Oil Supply Filter Replacement When Replacing The Turbocharger Or The Turbocharger Oil Supply Tube For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. When specified in the WSM, the turbocharger oil supply filter must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2019 vehicles equipped with a EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:APPLIANCE:AIR CONDITIONER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SSM 47909 - 2017-2019 Escape, MKC - License Plate Bracket Nut(s) Damaged With Over Torqued Screw(s) 2017-2019 Escape and MKC vehicles may exhibit a concern of the license plate bracket nut(s) being damaged due to the screw(s) being over torqued. The torque specification for these screws are 1.7 Nm (1.25 lb-ft). Engineering recommends not to use any power tool to tighten these screws. Most any power tool will apply more torque to the screws than the allowed torque specification and will damage the plastic nut(s).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2019 MKC vehicles equipped with memory mirrors built on or before 16-Feb-2019 may experience a ratcheting/clicking noise from the exterior mirror(s) glass which can occur when one or more of the following actions occur: customer unlocks vehicle, memory mirrors glass position recall to previous setting or memory mirrors button activation.
Source components: ELECTRICAL SYSTEM · VISIBILITY:REARVIEW MIRRORS/DEVICES:EXTERIOR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2017 vehicles may experience a no crank concern due to a security access key table error. When attempting to program keys or perform a parameter reset, the procedure may fail and the Integrated Diagnostic System (IDS) scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the Body Control Module (BCM) is internally faulted and requires replacement. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2017 vehicles may experience a no crank concern due to a security access key table error. When attempting to program keys or perform a parameter reset, the procedure may fail and the Integrated Diagnostic System (IDS) scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the Body Control Module (BCM) is internally faulted and requires replacement. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some all-wheel drive (AWD) 2013-2018 Escape vehicles equipped with 1.5L/1.6L/2.0L EcoBoost/Fusion vehicles equipped with 2.0L/2.7L EcoBoost/MKZ vehicles equipped with 2.0L EcoBoost, 2017-18 MKZ vehicles equipped with 3.0L EcoBoost, 2015-2018 MKC vehicles equipped with 2.0L/2.3L EcoBoost/Edge vehicles equipped with 2.0L/2.7L EcoBoost, 2016-2018 MKX vehicles equipped with 2.0L and 2.7L EcoBoost/Explorer vehicles equipped with 2.3L EcoBoost/Focus RS equipped with 2.3L EcoBoost, and 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost may exhibit a dark black fluid leak from the right side transfer case intermediate shaft seal. Follow the Service Procedure steps to correct the condition.
Source components: POWER TRAIN · POWER TRAIN:AXLE ASSEMBLY:AXLE SHAFT:SEAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some all-wheel drive (AWD) 2013-2018 Escape vehicles equipped with 1.5L/1.6L/2.0L EcoBoost/Fusion vehicles equipped with 2.0L/2.7L EcoBoost/MKZ vehicles equipped with 2.0L EcoBoost, 2017-18 MKZ vehicles equipped with 3.0L EcoBoost, 2015-2018 MKC vehicles equipped with 2.0L/2.3L EcoBoost/Edge vehicles equipped with 2.0L/2.7L EcoBoost, 2016-2018 MKX vehicles equipped with 2.0L and 2.7L EcoBoost/Explorer vehicles equipped with 2.3L EcoBoost/Focus RS equipped with 2.3L EcoBoost, and 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost may exhibit a dark black fluid leak from the right side transfer case intermediate shaft seal. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2012-2019 Vehicles may require repairs to the Smartlink system. Smartlink is a Ford Licensed Accessory which has a warranty provided by the accessory manufacturer. Warranty replacement parts for Smartlink that are ordered through Ford are not reimbursable through the Ford Motor Company warranty system. Please see the Warranty and Policy Manual for further information on Ford Licensed Accessories.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2019 MKC vehicles may exhibit an electronic power assist steering (EPAS) gear clatter-type noise over bumps that is only present on extremely rough road surfaces. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2019 Ford and Lincoln vehicles equipped with SYNC 3 and a 6, 8 or 10 inch screen may show a pop-up message every key cycle that states 'SYNC can check for updates when connected to a WiFi network'. To remove the inconvenience of the pop-up the customer can either connect to a trusted WiFi network to complete the setup process or turn off WiFi in the WiFi settings located under the Settings menu. Adjusting the setting for the customer is not a warrantable defect.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2018 C-Max, 2013-2019 Escape/Fusion/MKZ, 2015-2018 Focus, 2015-2019 Edge/F150/MKC/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017 Super Duty, 2018-2019 EcoSport/Expedition, and 2019 Nautilus vehicles may experience seat pan looseness, lateral movement, or clunk/thump noise on turns. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2013-2019 Escape and 2015-2019 MKC vehicles equipped with a power roof opening panel will exhibit a small vent opening position of 5 mm (.197 in). This is the normal vent position for optimal noise, vibration, harshness (NVH) and windnoise qualities. When the vent is closed, the front sliding glass panel will open to the 10 mm (.394 in) position and then close. The front sliding glass panel also opens to the 10 mm (.394 in) position to give the front sliding glass panel enough clearance before it opens to the rearward position. This is a normal operating characteristic of the front sliding glass panel. No repairs are required.
NHTSA source summary · Original PDF not reviewed by Recallfolio
For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. For all turbocharged engine applications, the turbocharger oil supply filter (6C683 gas engine/6L625 connector style or 6A968 diesel engine) must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.
Source components: ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2013-2019 vehicles equipped with a LKS system with customer complaints of steering wheel vibration, steering pull or vehicle drift may be due to an alert and/or steering aid input from the LKS. The LKS system detects unintentional drifting toward the outside of the lane and alerts and/or aids vehicle to stay in the lane. Be sure the customer understands how the lane departure warning feature settings work for Alert (steering wheel vibration) and Aid (steering input toward lane center). Further information on the LKS can be found in the owners manual. If the customers concern is due to the LKS functioning as intended, do not attempt to repair.
Source components: STEERING · STEERING: STEERING WHEEL/HANDLE BAR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When connecting the Vehicle Communication Module (VCM) and Integrated Diagnostic System (IDS) or Ford Diagnosis and Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic trouble codes (DTCs), no start, no crank conditions or the IPC inoperative. If a vehicle displays these issues, disconnect the equipment from the DLC and disconnect the vehicle battery. Wait 10 minutes and reinstall with the ignition off. Clear any DTCs present and retest.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2019 Escape and 2015-2019 MKC vehicles may exhibit a vibration attributed to the tires. Prior to performing any road force balancing procedures or related diagnosis, make sure the vehicle tire pressure is correct and is driven a minimum of 24 Km (15 miles) to eliminate any possible flat spotting conditions and potential misdiagnosis. Refer to Workshop Manual (WSM), Section 204-04A for further information. In addition, it is recommended that diagnosis of tire/wheel vibration should not be performed on tires with less than 320 Km (200 miles). Some initial tire/wheel vibration issues (such as flat spotting) may correct themselves after the tires have been in service for 320 Km (200 miles). Setting tire pressure to the correct placard pressure is contained within pre-delivery inspection.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2019 MKC vehicles may exhibit a whistle and/or wind noise at highway speed from the exterior mirror area. Use Workshop Manual (WSM), Section 100-04 and 501-00 for diagnosis of whistle and/or wind noise. If the exterior mirror(s) are identified as the source of the noise verify the distance between the exterior mirror base and the mirror cover before attempting other repairs. A minimum measurement of 1mm (0.0393 in) should be present between the exterior mirror base and the mirror cover. Refer to WSM, Section 501-09 for information on measuring and adjusting the distance between the exterior mirror base and mirror cover. If a minimum measurement of 1mm (0.0393 in) is not maintained between the exterior mirror base and the mirror cover when the exterior mirror(s) are serviced it may create a whistle and/or wind noise concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2018 Ford and Lincoln vehicles equipped with SYNC 3 may exhibit the Android Auto Preference menu selection is not present after an update to version 3.0 software. In prior versions of SYNC 3 software this menu was present, however in version 3.0 software the Android Auto Preference menu will only show up once an Android Phone has been initially connected to SYNC. This an operating characteristic of the Android Auto application after the SYNC 3.0 update and no repairs should be attempted.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When connecting the Vehicle Communication Module (VCM) and Integrated Diagnostic System (IDS) or Ford Diagnosis and Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic trouble codes (DTCs), no start, no crank conditions or the IPC inoperative. If a vehicle displays these issues, disconnect the equipment from the DLC and disconnect the vehicle battery. Wait 10 minutes and reinstall with the ignition off. Clear any DTCs present and retest.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2018 Escape vehicles equipped with 1.5L/1.6L/2.0L EcoBoost, 2013-2018 Fusion vehicles equipped with 2.0L/2.7L EcoBoost, 2013-2018 MKZ vehicles equipped with 2.0L EcoBoost, 2017-18 MKZ vehicles equipped with 3.0L EcoBoost, 2015-2018 MKC vehicles equipped with 2.0L/2.3L EcoBoost, 2015-2018 Edge vehicles equipped with 2.0L/2.7L EcoBoost, 2016-2018 MKX vehicles equipped with 2.0L and 2.7L EcoBoost, 2016-2018 Explorer vehicles equipped with 2.3L EcoBoost, 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost and 2016-2018 Focus RS equipped with 2.3L EcoBoost may exhibit a dark black fluid leak from the right side transfer case intermediate shaft seal. Follow the Service Procedure to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2015-2018 Edge, Fusion, Focus, MKZ, MKC, Escape vehicles equipped with a 2.0L EcoBoost engine may exhibit coolant consumption, white smoke and/or a runs rough condition. Refer to the extended coolant pressure test and checking for combustion gases in Workshop Manual (WSM), Section 303-03A. If internal coolant loss is confirmed, further investigation of the head gasket interface is required. Carefully inspect the cylinder block and head for erosion, pitting, and flatness defects, primarily between the cylinder to cylinder bore bridges. If defects to the aluminum surface on the cylinder block and/or cylinder head are found, follow the cost cap tool for component replacement. Follow WSM, Section 303-01A for the repair procedures
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2018 Ford and Lincoln vehicles equipped with SYNC 3 not at the latest software level may exhibit Various Performance Related concerns such as Display Operation, Navigation, Voice Recognition, Phone Pairing, Applink, Travel Link, Slow System Response, etc. Check for SYNC software update under the OASIS Tab SYNC selection. If an update is available refer to WSM, Section 415-00 and update the APIM software. After Installation, complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
If a trailer hitch receiver is installed on a 2013-2018 Escape or 2015-2019 MKC vehicle equipped with a hands-free liftgate, the hands-free liftgate function will become inoperative. Hands-free liftgate function can be restored by replacing the existing hands-free liftgate actuation upper sensor (14F680), lower sensor (14F680), stone deflector (17779), hands-free liftgate actuation module (14B291), plastic fasteners (N807951S) and screws (W506964) that are required for the factory installed trailer hitch receiver with hands-free liftgate option. Replacement of these parts to restore hands-free liftgate function is not warrantable. Regardless of trailer hitch configuration, the hands-free liftgate system cannot be added to a vehicle that was originally built without the hands-free liftgate option.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2018 Continental, MKC, MKX, MKZ, and Fusion vehicles with an instrument panel center mounted speaker and 2017-2018 Escape vehicles with Sony audio systems may exhibit an inoperative speed compensated volume feature. This may be due to the calibration in the audio control module (ACM). To correct the concern, reprogram the ACM to the latest calibration using the appropriate Ford scan tool release 110.03 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. For claiming, use causal part 18C869 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2015-2019 MKC vehicles are equipped with a satin chrome front grille and roof moldings. If they require cleaning due to stains, water spotting, or discoloring do not use Motorcraft Custom Bright Metal Cleaner which is used for bright chrome components. The following products are recommended for satin chrome components: Meguiar's M02 Mirror Glaze Fine Cut Cleaner (Product #M0216), Meguiar's Water Spot Remover (Product #A3714) or Turtle Wax Renew RX Premium All Metal Polish (SKU T284) or equivalent. Follow the manufacturers cleaning instructions.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2018 Ford and Lincoln vehicles with SYNC 3 may exhibit an intermittent blue or black screen. Check for SYNC software update under the OASIS Tab SYNC selection. If update is available refer to WSM, Section 415-00 and update APIM software. After Installation Complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various 2016-2018 vehicles with SYNC 3 may experience a touch screen that does not respond to any input. Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2018 Escape and 2017-2019 MKC vehicles may exhibit a lack of A/C cooling performance during PDI. This may be due to a insufficient/low refrigerant charge. If a vehicle displays a lack of cooling performance during PDI, inspect for a leak. Refer to the diagnostics in Workshop Manual (WSM), Section 412-00 for A/C leak detection. Many times when the system is only evacuated and refilled to the proper level at PDI the customer will return for a lack of cooling performance concern. A refrigerant leak will usually be identified as the root cause.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2017 Ford and Lincoln vehicles equipped with SYNC 3 version 2.2 software may exhibit a blank screen after attempting to exit Valet mode. SYNC software updates are now available under the OASIS Tab SYNC selection. If update is available, refer to WSM Section 415-00 and update APIM software. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 Fusion/MKZ/MKC/Escape/Edge vehicles equipped with a 2.0L EcoBoost engine may exhibit a runs rough condition with DTCs P0300, P0301, P0302, P0303, P0304 and/or P0316. This may be due to coolant intrusion due to corrosion on the engine block. To diagnose this concern, with the engine at normal operating temperature, pressurize the cooling system to 138 kPa (20 psi) and hold for 5 hours. If the coolant pressure drops 27.57 kPa (4psi), remove the spark plugs and inspect for coolant in the cylinders. If coolant is found in any of the cylinders, replace the engine long block assembly. Follow normal prior approval process for your Dealership. However, follow the diagnostic repair procedure in this article to determine correct repair. For claiming, use causal part 6006 and applicable labor operations in Section 6 of the SLTS Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Replacing the original equipment SYNC/Navigation system with either an aftermarket SYNC/Navigation kit or modifying original SYNC/Navigation parts to provide additional features is not recommended nor supported on any Ford, Mercury or Lincoln vehicle. Only approved Genuine Ford accessories or originally installed systems are supported and certified to function correctly with other vehicle systems. If you suspect a system has been modified, the following resources can be used to verify original equipment: Monroney Label (Window Sticker), Professional Technician Society (PTS) OASIS tab select SYNC or HVBOM. For Genuine Ford accessories use: PTS Workshop Tab select Dealer Installed Accessory or Accessory Installation.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2018 Ford and Lincoln vehicles equipped with SYNC 3 and connected to an iPhone recently upgraded to iOS 11.2.5 may exhibit functional concerns where USB audio playback and App Link will not operate. This may also include, under certain conditions, no Bluetooth streaming. Apple has released iOS 11.2.6 to address this concern. Advise the customer to update the device to iOS 11.2.6 and re-evaluate before performing any diagnosis or repairs for this condition. To check the iOS software level on an Apple iOS device, select Settings > General > About on the device.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various 2016-2017 vehicles with SYNC 3 may experience a touch screen that does not respond to any input. Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2017 MKC/MKZ, 2016-2017 MKX and 2017 Continental vehicles equipped with a Telematics Control Unit (TCU) built on or before 15-Aug-2017 may exhibit inoperative remote features via Lincoln Way Mobile app, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 with no modem electronic serial number (ESN) displayed. To correct, perform any open TCU Field Service Actions (FSAs). If U0198 DTC remains, remove the TCU fuse for 5 minutes then reinstall prior to programming. Perform IDS Network Test and reprogram the TCU using Integrated Diagnostic System (IDS) release 108.06 or higher. An internet connection is required. Calibration files may also be obtained at www.motorcraftservice.com. For claiming, use causal part 14G229 and applicable labor operations in section 10 of the SLTS manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2018 Ford and Lincoln Vehicle equipped with SYNC 3 and connected to an iPhone recently upgraded to iOS 11.2.5 may exhibit a concern where USB Audio playback and App Link applications will not function properly. This may also include, under certain conditions, no Bluetooth Streaming. Apple is aware of the issue and is working on a resolution with a future iOS release. No repairs should be performed at this time. To check the iOS software level on an Apple iOS device, select Settings > General > About on the device. Monitor OASIS for updates. Customers can also check Apple Support or connect to iTunes for the latest available iOS release for their phone.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2010-2018 various vehicles equipped with SYNC or SYNC 3 may not function when attempting to find or use the Spotify app via AppLink. As of an update released on 1/15/2018 Spotify will no longer be supporting their AppLink integration. No repair attempts should be attempted to correct this concern.