2020 Lincoln AVIATOR Manufacturer communications & TSBs.Page 2
Original record summaries, dates and identifiers for this model-year. Records 101–200 of 313, ordered newest first. Dated records on this page: Sep 1, 2021–Apr 6, 2023.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Apr 6, 2023Service Bulletin/Repair Instructions
TSB 23-2114
NHTSA communication ID: 10234127
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2021 Explorer/Aviator vehicles equipped with all-wheel drive (AWD) built on or before 30-Aug-2021 may exhibit an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTC) C00A6 and/or C0631. This may be due to the front axle disconnect actuator/intermediate shaft. To correct the condition, follow the Service Procedure to replace the front axle disconnect actuator/intermediate shaft with a revised intermediate shaft.
NHTSA source summary · Original PDF not reviewed by Recallfolio
For 2000-2024 Ford and Lincoln vehicles, swapping a module from a vehicle for diagnosis purposes is likely to cause errors and is not recommended. It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2023 Aviator vehicles built on or before 20-March-2023 may exhibit a passenger door window control switch to bezel rattle while audio volume is playing from speakers that could be mistakenly diagnosed as a speaker issue. This may be due to the natural frequencies of the switch and bezel when excited by sound. To diagnose, perform Workshop Manual (WSM) Section 415-00 > Pinpoint Test E1. Use the 100Hz audio sample file from the Speaker Audio Test link within Pinpoint Test E1, and adjust fade and balance settings to passenger front speaker. If the rattle is isolated to the passenger door switch bezel, remove per WSM Section 501-11. Apply Rotunda flock tape (164-R4903) over the underside of the bezel and the switch in a U-shape, then reassemble. Rerun Pinpoint Test E1 to verify the repair. If the rattle persists, perform the remaining Pinpoint Test E steps.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2023 Explorer/Aviator/Transit, 2021-2023 F-150/Bronco, 2022-2023 Expedition/Navigator/Mustang and 2023 F-250/F-350 Super Duty vehicles may exhibit harsh/delayed engagement and/or harsh/delayed shift concerns. These may be addressed with the powertrain control module (PCM)/transmission control module (TCM) Transmission Accelerated Main Control Break In Routine and/or a main control overhaul. Refer to Workshop Manual (WSM), Section 307-01, DTC Chart if DTCs are present and/or Diagnosis By Symptom to identify the clutch(s) to be cycled. Cycling the shift solenoids and clutch control valves to remove contamination must be performed along with an adaptive drive cycle before attempting repair. For claiming, use causal part 7A100 and applicable labor operations in Section 7 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2020-2023 Explorer/Aviator with start/stop push button ignition switch may exhibit an illuminated malfunction indicator lamp (MIL) and powertrain malfunction (wrench) indicator with diagnostic trouble code (DTC) B108A:01 (general electrical failure), B108A:24 (signal stuck high), and/or B108A:9E (stuck on). The ignition mode light emitting diode (LED) indicator may also flash quickly. This condition may be caused by loose wiring terminal crimps on connector C2195 at the push button ignition switch. Examine Pin 1 (CPK34/Gn) first, since it is the only pin with the smallest (26 gauge) wire. To correct this condition, repair terminal crimps per Wiring Diagram (WD) Cell 5. If no wiring terminal faults are found, refer to Workshop Manual (WSM) Section 211-05 for normal diagnostics. The push button ignition switch pinpoint tests in the WSM have been updated.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2023 Ford and Lincoln SYNC3 equipped vehicles may experience an inaccurate notification in the FordPassî/LincolnWayî app indicating Vehicle Has Entered Deep Sleep Mode. Vehicle Has Entered Deep Sleep Mode message is expected if the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SoC) drops below 50%. If the vehicle is going into deep sleep outside these conditions, this may be due to the telematics control unit (TCU) software. To correct this condition, follow the Service Procedure to update the TCU to the latest software. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2023 Explorer/Aviator 4x4/AWD vehicles with hybrid powertrain may experience a harshness and/or vibration felt through the seat, steering wheel and/or center console after initial driveaway between 25-50 MPH (40-80 Km/h) that lessens after driving 5-10 minutes. This may be due to driveshaft center bearing bounce mode during cold ambient temperatures. To resolve the concern, install a softer durometer L1MZ-4A499-F driveshaft center bearing per Workshop Manual Section 205-01. For claiming, use causal part 4A499 and applicable labor operations in Section 4 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2023 Ford and Lincoln vehicles equipped with a 10R60/10R80/10R80 MHT/10R100 transmission may exhibit a whine noise at idle and/or while driving. This may be identified as coming from the bellhousing and the front of the transmission fluid pan. The whine noise may become louder when the transmission is at operating temperature and may increase with engine revolutions per minute (RPM) in the park (P) position. A small amount of whine noise is considered to be characteristic of the 10R60/10R80/10R80 MHT/10R100 transmissions due to the offset gear drivetrain in the front support and has no effect on durability.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles equipped with a 2.7L, 3.0L,3.5L or 5.0L engine may require replacement of the long block engine assembly. New service kits have been released which include all the one-time-use components required in the service procedure for removal and replacement of the long block engine assembly. Refer to the Ford Electronic Parts Catalog (ECAT) for long block service kit part number by application.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2023 Explorer/Aviator vehicles may exhibit the A/C blowing warm air with DTCs P0645, P2CFC, and/or P2CFD present in the heating ventilation and air conditioning (HVAC) module. This may be due to spread terminal/terminal pushout in wire harness 14290 and on the corresponding pins to the body control module C (BCMC). Before replacement of the BCMC, disconnect all connectors from the BCMC and check the BCMC pins and wire terminals for damage. Refer to Workshop Manual (WSM), Section 419-10. If spread terminals or terminal pushout is present, repair as necessary. Refer to Wiring Diagram, Cell 005 for repair procedures. Reconnect all connections to the BCMC as indicated by the procedure in the WSM. Test the function of the A/C to verify that it is blowing cold air.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2021 Escape/Bronco Sport/Explorer and 2020-2021 Corsair/Aviator vehicles equipped with electric brake booster (EBB) built on or before 1-Aug-2022 may exhibit an illuminated anti-lock brake system (ABS) warning indicator and stability-traction control warning indicator with diagnostic trouble code (DTC) U3000:96 erroneously stored in the ABS module. This condition occurs during connection or power interrupt to the EBB module. If this code is stored and the ABS system has been reassembled, clear the DTC code using Ford Diagnosis and Repair System (FDRS) scan tool and check for recurrence. If the DTC persists, perform normal diagnostics. Refer to the Workshop Manual (WSM), Section 206-09 Anti-Lock Brake System. For claiming use the causal part number 2C219 and applicable labor operations in Section 2 of the Service Labor Time Standards.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2023 Aviator vehicles may exhibit a concern where the center display screen will not shift to night mode or has lines on the center display screen with multi color or rainbow hue. This may be due to accessory protocol interface module (APIM) software. To correct the condition, run the APIM-SYNC Module (APIM) Standard Programming application using the latest software level of the Ford Diagnosis and Repair System (FDRS). For claiming, use causal part 14G371 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: BACK OVER PREVENTION:DISPLAY FUNCTION · ELECTRICAL SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2020-2022 Aviator/Explorer/Police Interceptor, 2021-2022 F-150 vehicles equipped with a 10R80 MHT transmission and built on or before 15-Nov-2022 may exhibit an 8th gear start after coming to a stop and/or a no movement in Reverse condition. This may be due to the driver applying the accelerator pedal and brake pedal simultaneously during regenerative braking. To improve the condition, follow the Service Procedure to reprogram the powertrain control module (PCM) and refer the customer to the Automatic Transmission Section of the Owners Manual warning regarding applying both pedals simultaneously.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2023 F-150, Expedition, Navigator, Transit, Aviator and Explorer vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0627, P025A, P025B, P00C6, P008A and/or U0109 stored in the powertrain control module (PCM). This may be due to an intermittent or partial disconnect of the harness to the fuel pump control module (FPCM) connector, connector pin push-outs, damaged pins/terminals, or loose/corroded grounds. Inspect FPCM connector, applicable grounds (F-150 - G401, Expedition/Navigator - G403, Transit - G401, 2018-2019 Explorer G302, 2020-2022 Explorer/Aviator - G407) and confirm FPCM connector (F-150 - C4336, Expedition/Navigator - C433, Transit - C433, 2018-2019 Explorer - C3239, 2020-2022 Explorer/Aviator - C4033) is fully seated prior to performing PC/ED diagnostics or replacing any components.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Aviator vehicles may exhibit a concern where the center display screen will not shift to night mode or has lines on the center display screen with multi color or rainbow hue. This may be due to accessory protocol interface module (APIM) software. To correct the condition, run the APIM-SYNC Module (APIM) Standard Programming application using the latest software level of the Ford Diagnosis and Repair System (FDRS). For claiming, use causal part 14G371 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2023 Explorer/Aviator/Police Interceptor Utility vehicles equipped with a hybrid powertrain may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P2D40. This may be due to the high voltage battery thermal system not cooling as it should. Follow the updated WSM Section 414-03 including listed possible sources, visual inspection and prechecks, and diagnostic procedures.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles equipped with power folding mirrors may exhibit power folding mirrors that are inoperative or exhibit a clicking sound. This may be due to the mirrors being manually folded in, during transportation, going through a car wash, bumped in a parking lot, or found during pre-delivery inspection (PDI). Prior to the replacement of any components, attempt to synchronize the mirrors by following the Power Mirrors Synchronization procedure. Refer to Workshop Manual (WSM) Section 501-09 Rear View Mirrors - General Procedures - Power Mirrors Synchronization.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 22-2176 to increase the labor operation allowance and update the part list. Some 2020-2022 Escape/Corsair vehicles built on or before 3-Jan-2022, 2020-2022 Explorer vehicles built on or before 14-Feb-2022, 2020-2022 Aviator vehicles built on or before 07-Feb-2022 and 2021-2022 Bronco Sport vehicles built on or before 3-Dec-2021 may exhibit a slow fuel fill and/or spit back condition during refueling. This may be due to the design of the fuel tank filler pipe. To correct the condition, follow the Service Procedure to replace the fuel tank filler pipe.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2020 Edge, 2016-2018 MKX, 2019-2020 Nautilus, 2018-2021 Expedition/Navigator, and 2020-2021 Escape/Corsair/Explorer/Aviator vehicles may exhibit an inoperative power liftgate. This may be due to the rear gate trunk module (RGTM) software. To correct the condition, reprogram the RGTM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 14B291 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2023 Ford and Lincoln vehicles equipped with a telematic control unit (TCU) may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization, and/or modem electronic serial number (ESN) could not be displayed in the center display screen. To correct this condition prior to programming, remove the TCU fuse for 5-minutes then reinstall. Delete all previous session files for the vehicle. Start a new Ford Diagnosis and Repair System (FDRS) session. Perform a TCU provisioning and Program the TCU to the latest FDRS version level. If the concern is still present, follow normal diagnostics in Workshop Manual (WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2023 Lincoln Aviator and 2020-2022 Lincoln Corsair vehicles may exhibit courtesy lamps not illuminating with a door open or always on. Also, ambient lighting may be inoperative or always on. If this concern occurs, check the center console cup holder area for evidence of liquid intrusion first. Liquid can short the local interconnect network (LIN) circuit. Temporarily disconnect the console inline connector(s) during diagnosis to isolate circuit shorts. Search Wiring Diagram (WD) for *cup holder ambient* to display the related connectors. If a short is found in cup holder ambient light ring light emitting diode (LED) connector, repair as necessary. If no evidence of liquid intrusion is found, continue with normal Workshop Manual (WSM) diagnostics.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Explorer/Aviator vehicles equipped with a 3.0L EcoBoost engine may exhibit a ticking/tapping or rattle type noise from the top front cover area of the engine on initial start-up after a cold soak of 6 hours or more that may last for 2-5 seconds. This may be due to a worn variable cam timing (VCT) unit. To correct the condition, follow the Service Procedure to replace the VCT units.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Ford and Lincoln vehicles equipped with a telematic control unit (TCU) may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization, and/or modem electronic serial number (ESN) could not be displayed in the center display screen. To correct this condition prior to programming, remove the TCU fuse for 5-minutes then reinstall. Delete all previous session files for the vehicle. Start a new Ford Diagnosis and Repair System (FDRS) session. Perform a TCU provisioning and Program the TCU to the latest FDRS version level. If the concern is still present, follow normal diagnostics in Workshop Manual (WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: COMMUNICATION:MANUFACTURER TELEMATICS · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2023 Aviator vehicles might experience a series of lines on the center display screen with multi colors or a rainbow hue. Replacement or reprogramming of the accessory protocol interface module (APIM) will not resolve this condition. Inform customers that engineering is currently working on a solution for this condition and will be released via an over the air (OTA) software update expected in December 2022. Software will update automatically if the vehicle is connected to FordPass/LincolnWay. Monitor OASIS for additional information. Schedule a service appointment for customers that are not connected to FordPass/LincolnWay once the repair becomes available.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Aviator vehicles might experience a series of lines on the center display screen with multi colors or a rainbow hue. Replacement or reprogramming of the accessory protocol interface module (APIM) will not resolve this condition. Inform customers that engineering is currently working on a solution for this condition and will be released via an over the air (OTA) software update expected in December 2022. Software will update automatically if the vehicle is connected to FordPass/LincolnWay. Monitor OASIS for additional information. Schedule a service appointment for customers that are not connected to FordPass/LincolnWay once the repair becomes available.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Explorer/Aviator/Police Interceptor Utility vehicles equipped with a hybrid powertrain may exhibit an illuminated MIL with diagnostic trouble code (DTC) P2D40. This may be due to the chiller not interpreting the correct cooling value of the high voltage battery chiller. To correct the condition, follow the Service Procedure to diagnose the cause of the incorrect value.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Explorer/Aviator vehicles may exhibit automatic transmission fluid (ATF) contamination in the engine cooling system due to the transmission cooler. If the cooling system becomes contaminated with ATF, the system must be flushed clear of the contamination after the source of the contamination has been repaired. It is generally not necessary to replace the following components due to ATF contamination in the cooling system: radiator, heater core, de-gas bottle, water pump, auxiliary water pump, coolant control valves, temperature sensors, thermostat, turbocharger, heat exchangers, tubes, gaskets/O-rings/seals (unless removed), or rubber coolant hoses (unless swollen).
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Aviator Plug In Hybrid (PHEV) vehicles built on or before 14-Jan-2022 may exhibit a 12-volt battery discharged while the vehicle is plugged in during high voltage battery charging and/or inoperative level 2 charger (220/240 volts) at customers residence but charging performance operates as intended at a dealership or other locations. This may be due to the software in the battery charger control module (BCCM) (also known as secondary on-board diagnostic module SOBDM). To correct the condition, follow the Service Procedure to reprogram various modules starting with the PCM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2022 Ford/Lincoln vehicles equipped with a wireless charging pad may exhibit one of the following if the customer is using a Magsafe iPhone (iPhone 12 or 13): slow charging, inoperative, notification that the phone has been mispositioned on the charging pad and/or the phone charging icon in the center screen display is not showing. This may be due to a compatibility issue between the customer's phone and the wireless accessory charging module (WACM) that may make it difficult for Ford and Lincoln vehicles to wirelessly charge these specific phones. The phone can still be charged using the USB cable if the vehicle experiences the above symptoms. If the customer is using a Magsafe iPhone such as an iPhone 12 or 13, verify the wireless charging pad works with a Qi certified phone prior to any part replacements.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2022 Ford/Lincoln customers may experience a notification in the FordPassÃÂÃÂÃÂî/LincolnWayÃÂÃÂÃÂî app indicating Vehicle Has Entered Deep Sleep Mode. This occurs when the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SOC) drops below 50%. A warning may also set if the telematic control unit (TCU) has received an over the air update. The TCU powers down all communication when in this mode and app features are disabled. Manually start the vehicle to wake if from mode. More information is located in the app under: Account > Help > search 'Deep Sleep' in the entry box. If the condition remains, check the BCM 12v SOC. If the SOC does not change after charging the battery or after BMS reset is performed, continue with normal battery and/or BMS sensor diagnostics.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Aviator vehicles may exhibit a door ajar or door fault warning message present in the message center with diagnostic trouble codes (DTCs) B1175:19, B1176:19, B11C0:19 and/or B11C1:19 present in door latch control module E (DCME), door latch control module F (DCMF), door latch control module G (DCMG) and/or door latch control module H (DCMH). This may be due to low battery voltage and DTC thresholds being too low and not a fault in the door latch assembly. To correct the condition, reprogram and re-configure the the affected module using the latest level of the Ford Diagnosis and Repair System (FDRS). For claiming use causal part 54264A27 and applicable labor times found in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019-2022 Edge/Nautilus, 2018-2022 Expedition/Navigator, 2020-2022 Explorer/Aviator vehicles equipped with a family entertainment system may experience the audio is not synchronized with the video display when using the vehicle speakers. To correct this condition, contact the VOXX Customer Service Department at 1-866-869-7888. For claiming, refer to the Warranty and Policy manual for Ford Licensed Accessories.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2021 Aviator vehicles equipped with air suspension may exhibit a Drive Malfunction and/or Suspension Fault message in the instrument panel cluster (IPC) with diagnostic trouble codes (DTCs) B1041 and U2100 stored in the SUMA. This may be due to the SUMA entering into a diagnostic service mode after an on-demand self-test or module replacement. If no other DTCs are present, use the latest software version of the Ford Diagnosis and Repair System (FDRS) scan tool to update and configure the SUMA. If other DTCs are present, refer to Workshop Manual (WSM), Section 204-05 for normal diagnostics. For claiming use causal part 5319 and applicable labor times found in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Explorer/Aviator vehicles may exhibit a lack of audio and/or a water leak in the rear liftgate area and/or water in the spare tire area. The customer may indicate that this concern is more noticeable after a car wash or rainfall. To correct the condition, follow the Service Procedure to identify the leak path.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Explorer/Aviator/Police Interceptor Utility vehicles may exhibit a rear differential that is venting rear axle fluid. This may result in a noise, smell, or leak noticed by the customer. Inspect the rear of the vehicle for signs of rear differential fluid venting in the right rear wheel well (oil staining in the wheel well liner and/or oil residue on the wheel end assembly below) or leaking from the rear differential. If signs of fluid leaks are found from any seals, repair as necessary. Refer to Workshop Manual (WSM), Section 205-02. If no seal leaks are found but fluid is venting, drain the rear differential and re-fill with fresh rear differential fluid. Remove the vent tube and use compressed air to verify that the fluid vent tube is clear. Reinstall the vent tube. Engineering is investigating, monitor OASIS for updates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Mustang/Ranger/Transit Connect, 2020-2021 EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator, 2021 Bronco Sport and 2020-2022 Explorer/Aviator vehicles with SYNC 3 may experience various SYNC performance related concerns. This may be due to the SYNC Software. To correct the condition, follow the Service Procedure to update the accessory protocol interface module (APIM) software.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2021 Expedition/Navigator and 2020-2021 Explorer/Aviator vehicles equipped with a 10R80/10R80 MHT or 10R60 may exhibit a momentary transmission neutral-out condition while in drive. Vehicle may also have diagnostic trouble code (DTC) P07E6 and/or P07E4 stored in the powertrain control module (PCM) or transmission control module (TCM) and/or a possible audible noise. This may be due to a leak in the park valve circuit. To correct the condition, follow the Service Procedure to inspect the park system hardware for wear or damage and replace the valve body separator plate with an improved valve body separator plate.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2020-2022 Explorer/Aviator and 2021-2022 F-150 hybrid vehicles equipped with a 10R80 MHT require the Transmission Strategy Download application in the Ford Diagnosis and Repair System (FDRS) to be run after certain transmission or module repairs. The Transmission Strategy Download routine is failing in FDRS levels 32.5.3 and 32.5.4. The FDRS development team is working to resolve this in a future release of FDRS. In the meantime, uninstall FDRS from the computer using the select all function to remove all data and recordings. Reinstall the older FDRS version 31.6.5 using this url - http://www.fordservicecontent.com/Ford_Content/IDS/FDRS/FDRS_31.6.5.exe Once 31.6.5 is installed, download and run the Transmission Strategy Download application.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Explorer/Aviator vehicles may exhibit a concern of inoperative, rattling, crackling and/or distorted sound from one or more speakers. In order to correct the condition, make sure to completely follow the diagnostics in Workshop Manual (WSM), Section 415-00, Pinpoint Test D for vehicles without SYNC 3, and WSM, Section 415-00B, Pinpoint Test E for vehicles equipped with SYNC 3. If the diagnostics point towards speaker replacement, remove and re-center the speaker, making sure to tighten to the specified torque and retest. Refer to WSM, Section 415-00.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Explorer/Aviator/Police Interceptor Utility vehicles may exhibit erratic transfer case operation and/or noise. This may be due to water intrusion between the transmission and the transfer case. The transfer case installation procedure has been updated in Workshop Manual (WSM), Section 307-07B to prevent this concern from reoccurring. Follow the updated WSM procedure to make sure the top of the transfer case is sealed upon installation.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2022 Ford and Lincoln vehicle owners may experience a condition of missing authorization, command and control, battery charging details or phone-as-a-key setup buttons/selections in their FordPass or LincolnWay App. This condition is due to an error within the FordPass or LincolnWay App and not due to a concern on the vehicle. Verify that the customers FordPass or LincolnWay App is at the latest version. Replacement or reprogramming of the telematics control unit (TCU)/gateway module (GWM)/remote function actuator (RFA) will not resolve this condition. If the condition persists, utilize the FordPass Guides or Lincoln Way Concierge teams.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Aviator vehicles may exhibit an issue transitioning to night mode in low ambient light conditions. This may be due to accessory protocol interface module (APIM) software. Inform customers that engineering is currently working on a solution for this condition and will be released via an over the air (OTA) software update expected in July 2023. Software will update automatically if the vehicle is connected to LincolnWay. Monitor OASIS for additional information. Schedule a service appointment for customers that are not connected to LincolnWay once the repair becomes available.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Escape/Corsair vehicles built on or before 3-Jan-2022, 2020-2022 Explorer vehicles built on or before 14-Feb-2022, 2020-2022 Aviator vehicles built on or before 07-Feb-2022 and 2021-2022 Bronco Sport vehicles built on or before 3-Dec-2021 may exhibit a slow fuel fill and/or spit back condition during refueling. This may be due to the design of the fuel tank filler pipe. To correct the condition, follow the Service Procedure to replace the fuel tank filler pipe.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Explorer/Aviator vehicles may exhibit a second row folding seat that is inoperative or requires excessive effort to fold. This may be due to tension built up within the seat and seat track that leads to more force required to manually fold the seat. To correct the condition, the second row seat frame will need to be unbolted from the floor and tightened in the correct sequence. Additionally, the sliding tracks of the seat should be inspected for proper alignment when tightening the bolts. It is important to note that the bolts should be started by hand before tightening to the correct torque. This sequence is outlined in Workshop Manual (WSM), Section 501-10. The WSM has been updated to reflect the updated bolt installation procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Corsair/Nautilus/Navigator/Aviator, 2021-2022 Mustang Mach-E vehicles equipped with Phone-as-a-Key may exhibit Phone-as-a-Key concerns and have diagnostic trouble code(s) (DTC) U200D:15, U200E:15, U200F:15, B15**:31, B15**:49 and/or B15A5:56 stored in the remote function actuator (RFA) module. If the vehicle is exhibiting other symptoms outside of Phone-as-a-key concerns, address those first. If any of these DTCs are detected during diagnostics, clear the DTCs, reflash RFA to the latest software level and start a new Ford Diagnosis and Repair System (FDRS) session. Verify that DTCs are no longer present. If only the B15**:31, B15**:57 and/or B15A5:56 DTC(s) returns in the RFA after a self test, follow normal Workshop Manual (WSM) diagnostics, Section 419-01C.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2022 F-150, Expedition, Navigator, Transit, Aviator and Explorer vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0627, P025A, P025B, P00C6, P008A and/or U0109 stored in the powertrain control module (PCM). This may be due to an intermittent or partial disconnect of the harness to the fuel pump control module (FPCM) connector, connector pin push-outs, damaged pins/terminals, or loose/corroded grounds. Inspect FPCM connector, applicable grounds (F-150 - G401, Expedition/Navigator - G403, Transit - G401, 2018-2019 Explorer G302, 2020-2022 Explorer/Aviator - G407) and confirm FPCM connector (F-150 - C4336, Expedition/Navigator - C433, Transit - C433, 2018-2019 Explorer - C3239, 2020-2022 Explorer/Aviator - C4033) is fully seated prior to performing PC/ED diagnostics or replacing any components.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2021 Explorer/Aviator vehicles may exhibit inoperative third row power seat folding. This may be due to the software in the power fold seat module (SCMJ). To correct the condition, connect a battery charger and reprogram the SCMJ using the latest software level of the appropriate Ford diagnostic scan tool. After reprogramming the SCMJ, perform a manual re-learn procedure. With the engine running, tailgate open, and no objects in the third row seats, press and hold the both seat fold button for one minute until both seats completely fold and unfold. Refer to Owner's Manual for information. Verify that each seat operates correctly after the relearn procedure by pressing the left and then the right third row seat fold buttons. For claiming, use causal part 14F042 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Explorer/Aviator vehicles may exhibit the A/C blowing warm air with DTCs P0645, P2CFC, and/or P2CFD present in the heating ventilation and air conditioning (HVAC) module. This may be due to spread terminal/terminal pushout in wire harness 14290 and on the corresponding pins to the body control module C (BCMC). Before replacement of the BCMC, disconnect all connectors from the BCMC and check the BCMC pins and wire terminals for damage. Refer to Workshop Manual (WSM), Section 419-10. If spread terminals or terminal pushout is present, repair as necessary. Refer to Wiring Diagram, Cell 005 for repair procedures. Reconnect all connections to the BCMC as indicated by the procedure in the WSM. Test the function of the A/C to verify that it is blowing cold air.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Explorer/Aviator vehicles may exhibit an inoperative power liftgate when using intelligent access (IA) features such as the hands free liftgate or when using the outside control button on the liftgate handle when the doors are locked. This may be due to a poor wiring connection at connector C4332 for the rear keyless entry antenna. If these symptoms are present, inspect C4332 (below the liftgate striker) for a poor connection, loose terminals, or improper pin-fit.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2023 Ford or Lincoln vehicles with modems activated through FordPass or LincolnWay may experience 12 volt battery drain symptoms when the customer uses non-Ford/Lincoln phone applications as an alternate channel to access vehicle commands such as door lock/unlock, remote start, vehicle location, etc. The battery drain may be caused by excessive calls for data through the vehicle network keeping it in an activated state. Recommend that the customer uninstall the app to ensure this is not contributing to battery symptoms experienced. Advise the customer that unaffiliated third-party app developers do not work directly with Ford to adhere to security, vehicle communication, and privacy requirements.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Explorer/Aviator and 2021-2022 Bronco vehicles may exhibit an illuminated airbag warning indicator with diagnostic trouble code (DTC) B1404:13 and/or B1407:13. This may be due to contamination and relative movement in the connection between the wiring harness and the side airbag. To correct the condition, follow the Service Procedure to replace the affected connector with a service pigtail and the affected side airbag.
Source components: AIR BAGS:SRS MALFUNCTION WARNING LAMP/LIGHT · ELECTRICAL SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Explorer/Aviator/Police Interceptor Utility vehicles may exhibit erratic shifting and/or a transmission fluid venting condition. If during the preliminary inspection the transmission fluid is found to be a foamy pink color this may indicate possible cross contamination of engine coolant and transmission fluid due to an internally leaking transmission fluid cooler assembly. When repairing or replacing the transmission assembly for an internally leaking transmission fluid cooler assembly, use causal part 7869 and applicable labor operations in Section 07 of the Service Labor Time Standards (SLTS) Manual.
Source components: ENGINE · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Explorer/Aviator/Police Interceptor Utility vehicles equipped with a 10R60/10R80 automatic transmission may exhibit a harsh engagement/harsh shift/delayed shift with or without an illuminated malfunction indicator lamp (MIL) or diagnostic trouble codes (DTCs) P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6, P07F7, P2700, P2701, P2702, P2703, P2704 and/or P2705 stored in the powertrain control module (PCM). This may be due to sticking valves in the main control valve body. To correct the condition, follow the Service Procedure steps to perform the PCM - Transmission Accelerated Main Control Break In routine for the appropriate clutch(s) and/or overhaul main control valve body.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2021 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Explorer/Aviator vehicles equipped with a power adjustable steering column may exhibit a creak/squeal type noise during up or down travel, including ingress/egress and/or driver memory function. This symptom may be more prevalent with warmer interior temperatures and/or during summer months. This may be due to a lack of lubrication in the steering column. To correct the condition, follow the Service Procedure to replace the steering column.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2022 F-150, Expedition, Navigator, Transit, Aviator and Explorer vehicles may exhibit an illuminated MIL with Diagnostic Trouble Codes (DTCs) P025A, P025B, P00C6, P008A and/or U0109 stored in the powertrain control module (PCM). This may be due to an intermittent or partial disconnect of the harness to the fuel pump control module (FPCM) connector, connector pin push-outs or loose/corroded grounds. Inspect FPCM connector, applicable grounds (F-150- G401, Expedition/Navigator- G403, Transit- G401, 2018-2019 Explorer G302, 2020-2022 Explorer/Aviator- G407) and confirm FPCM connector (F-150- C4336, Expedition/Navigator- C433, Transit- C433, 2018-2019 Explorer C3239, 2020-2022 Explorer/Aviator- C4033) is fully seated prior to performing PC/ED diagnostics or replacing any components.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
In various 2017-2022 Ford and Lincoln vehicles, customers may receive a message in the FordPass or LincolnWay App stating "Feature Unavailable. Since this is a fleet vehicle, it cannot access the (SYNC Connect) FordPass or LincolnWay app through the TCU Embedded Modem. If this message appears, the vehicle may be equipped with a fleet telematics module. Replacement of the TCU or TCU related repairs will not prevent this message from appearing. Please refer the customer to in app FordPass Guides or LincolnWay Concierge Teams to aid with fleet telematics removal. Open app, select Account > Help > CHAT or CALL option
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Aviator Hybrid vehicles may exhibit an illuminated MIL and a Stop Safely Now message with only DTC P1A0C stored in the PCM. This may be due to the software in the battery energy control module (BECM). The condition occurs when the vehicle is started when the charging cord is connected. To prevent the condition from occurring, disconnect the charger prior to starting the vehicle. If the charger is not disconnected before starting, the ignition will need to be cycled before driving. Inform customers that they can continue to drive the vehicle and engineering is currently working on a solution for this condition that is expected in May-2022. No additional diagnosis or service is required for this condition at this time. Monitor OASIS for updates and schedule a service appointment for customers once the repair becomes available.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Explorer/Aviator vehicles equipped with a 3.0L EcoBoost engine may appear to have a low engine oil level if the proper procedures are not followed. Refer to the Owner's Manual, Maintenance, Engine oil check section. When checking the engine oil level after shutting off the engine wait at least 15 minutes prior to checking in order to allow the oil to drain back to the oil pan. The engine oil level can be checked immediately if the engine has not been started. When changing the engine oil the engine needs to be at normal operating temperature and the oil filter removed before draining the oil. Allow the oil pan to drain completely for up to 5 minutes. Check oil level after filling by following the oil level check procedure.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 - 2022 Explorer/Aviator/Police Interceptor Utility vehicles may display a distance to empty value in the instrument panel cluster (IPC) that does not correctly represent the actual fuel level of the vehicle. This may be due to excessive idling and/or a learned value in the powertrain control module (PCM) that is incorrect. To correct the condition, perform the PCM - Reset the Keep Alive Memory (KAM) application in the appropriate Ford diagnostic scan tool. For claiming, use Causal Part 12A650 and applicable labor times from Section 10 in the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 21-2185 to update the vehicle model years affected. Some 2020-2022 Explorer/Aviator/Corsair vehicles may experience seat pan looseness, lateral movement and/or clunk/thump noise on turns. To correct the condition, follow the Service Procedure steps to reinforce the cushion hook.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Explorer/Aviator non-hybrid vehicles may exhibit radio static and/or poor radio sound quality when moving. This may be more noticeable on AM radio stations. This may be caused by an electromagnetic interference concern. To correct the condition, follow the Service Procedure to install new grounds on the rear knuckle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Aviator vehicles may exhibit a door ajar or door fault warning message present in the message center with diagnostic trouble codes (DTCs) B1175:19, B1176:19, B11C0:19 and/or B11C1:19 present in door latch control module E (DCME), door latch control module F (DCMF), door latch control module G (DCMG) and/or door latch control module H (DCMH). This may be due to low battery voltage and DTC thresholds being too low and not a fault in the door latch assembly. Engineering is releasing updated software to resolve this concern, which is expected to be available by the end of June-2022. In the meantime, clear these DTC's and if any reset with normal battery voltage follow normal Workshop Manual diagnostics and repair. Monitor OASIS for updates.
Source components: ELECTRICAL SYSTEM · LATCHES/LOCKS/LINKAGES · STRUCTURE:BODY:DOOR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 20202022 Escape/Aviator plug-in hybrid electric vehicle (PHEV) and 20212022 Corsair PHEV vehicles may exhibit a FordPass or LincolnWay App message notification indicating deep sleep mode and connectivity is temporarily unavailable while the vehicle is plugged in during high voltage battery charging. The vehicle may also exhibit an inoperative remote start feature and/or lock and unlock functionality. This may be due to the software in the telematics control unit (TCU). To correct this condition, follow the Service Procedure to reprogram the TCU.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Explorer/Aviator vehicles equipped with all-wheel drive (AWD) may exhibit an illuminated stability-traction control and/or powertrain malfunction warning indicators with diagnostic trouble codes (DTCs) C00A8:11, C00A8:13, C00A6:71, C00A6:74, and C00A6:99 present in the AWD module. This may be due to a damaged wiring harness rubbing against the underbody heat shield where it routes over and into the transfer case actuator motor. Inspect the wire harness for damage and repair as necessary following the procedures in the Wiring Diagram Manual. If no damage is found, continue with normal diagnostics.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2018 Focus/MKX/C-MAX, 2017-2019 MKC/Taurus/Flex/MKT, 2017-2020 Fusion/MKZ/Continental, 2017-2022 Mustang/Edge/Explorer/Police Interceptor Utility/Escape/F-150/F-Super Duty, 2018-2022 Expedition/Navigator, 2019-2022 Ranger/Nautilus, 2020-2022 Corsair/Aviator, and 2021-2022 Mustang Mach-E vehicles may exhibit a noisy, incorrectly operating, and/or inoperative seat motor. This may be due to a damaged or inoperative seat track motor. A lower level service part has been released to correct noisy, incorrect operation/inoperative seat track motors.
NHTSA source summary · Original PDF not reviewed by Recallfolio
In all of the affected vehicles, the vehicle emission control information (VECI) label includes incorrect information. The correct label should show Evap: LFMXR0165LDG. Owners of affected vehicles will be mailed the VECI label and installation instructions early May 2022. Owners will be given the option of installing the labels themselves, or they can have their dealer perform the service for them.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2021 Explorer/Aviator/Escape/Corsair, 2021-2022 Bronco Sport, and 2022 Maverick vehicles may exhibit an inoperative driver door window control switch (windows inoperative, mirror control unresponsive, etc.). Diagnostic trouble code (DTC) B1088:87 may be present in the driver door module (DDM). This may be due to the software in the DDM. To correct the condition, reprogram the DDM with the latest software level of the Ford Diagnosis and Repair System (FDRS). After reprogramming the DDM, run the DDM configuration application and perform a window learn routine via FDRS. For claiming, use causal part 14B291 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:WIRING:SWITCHES/KNOBS/BUTTONS · STRUCTURE:BODY · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Explorer/Aviator vehicles may exhibit a wind/whistle type noise at highway speeds originating from the front A-pillar applique (either side or both). This may be due to a small gap between the outboard side of the A-pillar applique and the moulding. To correct the condition, follow the Service Procedure to install thin strips of flock tape on the A-pillar applique.
Source components: STRUCTURE:BODY · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Explorer/Aviator vehicles may exhibit a driveline vibration. Workshop Manual (WSM) Pinpoint Tests G (driveline shudder) and H (driveline vibration) have been updated in WSM, Section 205-01.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 F-Super Duty/Explorer/Aviator and 2021-2022 F-150 vehicles may exhibit a Front Camera Fault, Lane Keeping Fault, and/or Collison Warning Not Available message with various diagnostic trouble codes (DTC) stored in the image processing module A (IPMA). If programming fails or Ford Diagnosis and Repair System (FDRS) states a file failed to flash after replacing the IPMA or reprogramming IPMA software, test the battery using any approved Rotunda tool including the GR-190, GRX-3590, and DCA-8000. Fully recharge or replace the battery according to results of the tool. Set the battery charger to maintain battery voltage between 12.6 and 13.6 volts during the entire programming procedure. The IPMA programming procedure may take several hours to complete due to the size of the software files required.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2011-2022 Explorer and 2020-2022 Aviator vehicles may experience an inoperative roof opening panel motor. If diagnostics lead to a motor replacement, visually inspect the original motor for signs of water intrusion. If found, determine source of water leak prior to replacing the motor. Refer to Workshop Manual (WSM), Section 501-17, Pinpoint Test A for 2011-2016 and Pinpoint Test B for 2017-2022 for identifying the source of the water leak.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Explorer/Aviator/Police Interceptor Utility vehicles and 2021 F-150 vehicles equipped with a 10R80 MHT automatic transmission may exhibit a harsh/delayed engagement and/or a harsh/delayed shift with or without an illuminated malfunction indicator lamp (MIL) or diagnostic trouble codes (DTC) P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6, P07F7, P2700, P2701, P2702, P2703, P2704 and/or P2705 stored in the powertrain control module (PCM). This may be due to sticking valves in the main control valve body. To correct the condition, follow the Service Procedure steps to perform the PCM - Transmission Accelerated Main Control Break In routine for the appropriate clutch(s) and/or overhaul the main control valve body.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2021 Ford and Lincoln vehicles equipped with SYNC 3 may exhibit a condition where the navigation voice prompts are inoperative after a SYNC map update. This may be due to an incomplete installation of the SYNC map software. If possible, using the original USB that installed the update, reperform the update and verify the navigation voice prompts have returned. Multiple reboots are expected when this update is being performed. Verify the Installation Is Complete message displays in the touch screen. If the original USB is not available, go to website https://syncnavigation.com/ford/home or https://syncnavigation.com/lincoln/home to download the files once more for the affected vehicle. For further map update support, reference the FAQ section on these websites.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2021 Aviator vehicles equipped with a 3.0L PHEV powertrain may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) U0100, P1A42 and/or P1A43 stored in battery energy control module (BECM). This may be due to software in the PCM. To correct the condition, follow the service procedure to perform a coordinated flash on the powertrain control module (PCM), secondary on-board diagnostic module c (SOBDMC), anti-lock braking system (ABS) module, BECM, and battery charger control module (BCCM).
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Explorer/Aviator vehicles may exhibit poor sound quality from the left and/or right front speaker while using Bluetooth audio. This may be due to concerns with the wiring harness or connections of connector C2383A, C202, and/or C4240B. Prior to the replacement of the affected speaker, inspect the inline connections at connectors C2383A, C202, and C4240B for damage or incorrect pin fit. If no concerns are found with the wiring harness, continue with the replacement of the affected speaker.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Explorer/Aviator vehicles may exhibit an illuminated MIL with multiple diagnostic trouble codes (DTC). These DTCs may include P04F0, P008A, P0451, P0455, P0456, P0496 and/or P018C. This may be due to the wiring harness connection at connector C1198. Prior to replacement of any components, inspect the connector and wiring harness for any damage or pin fit concerns. If any damage or pin fit concerns are found, repair the connector or harness as necessary. If no damage or pin fit concerns are found, refer to normal diagnostics.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2021 Ford and Lincoln vehicles may exhibit inoperative remote features via the Ford Pass/Lincoln Way mobile app, incomplete user authorization, no modem electronic serial number (ESN) displayed or DTCs U2100 and/or B156D in the telematics control unit (TCU). These symptoms may persist even after performing a TCU software update and/or replacement. To correct this condition, start a new session with the latest version of the appropriate diagnostic scan tool and perform a PMI on the TCU. If issues persist, open a hotline assistance request and include the IDS version (if applicable) used to perform the PMI and the Authorization Status PID value in the TCU datalogger. For claiming use causal part 14G229 and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2021 Explorer/Aviator/Police Interceptor Utility vehicles equipped with AWD may exhibit a binding or shudder sensation while turning and/or while accelerating from low speeds. The concern may also be described as a grinding and/or chatter noise. If the Workshop Manual (WSM) leads to replacement of the rear axle, inspect the differential for damage and differential fluid for metallic chunks in the fluid. Note that some metallic flake in the fluid and/or discoloration is normal and the rear axle should not be replaced for it. If no damage is found to the rear differential, it is not recommended to replace the rear axle assembly. Instead, refer to the Symptom Charts in WSM, Section 308-07 for further diagnosis of the transfer case.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2021 EcoSport, Expedition, Navigator; 2019-2021 Ranger; 2020-2021 Escape, Corsair, Explorer, Transit; 2021 Bronco, Bronco Sport, Edge, Nautilus, F-150, Mustang; 2019-2022 Transit Connect; 2020-2022 Aviator, F-Super Duty; and 2022 Maverick vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0496, P0456, P0455, P04F0, and/or P0451. Ford has tested returned EVAP canister purge valves and found them to be fully functional. Prior to replacing the canister purge valve or other EVAP components, perform the following tests using the Ford Diagnosis and Repair System (FDRS) Scan Tool: Full System EVAP Leak Test - FDRS Location: TOOLBOX > PCM > PCM - Evap Emissions System Test and the EVAP Purge Valve Leak Test - FDRS Location: TOOLBOX > PCM > Evap Emission System Toolbox > CPV Check.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 21-2342 to update the Issue, Action, and Service Procedure. Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Mustang/Ranger/Transit Connect, 2020-2021 EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator and 2021 Bronco Sport vehicles with SYNC 3 may experience various SYNC performance related concerns including but not limited to: Sirius audio not functioning properly after a key cycle with active subscription Presets not responding or indicating properly Intermittent audio echo/robotic voice heard during a Bluetooth phone call Wi-Fi connection message pop-up every key cycle Frozen unresponsive touchscreen Solid blue screen when moving forward at speeds above 16 km/h (10 mph) (2019 vehicles only) Rear parking aid camera remains on the screen at speeds below 16 km/h (10 mph) (2019 vehicles only) Inoperative infotainment applications Poor/no AppLink function Apple CarPlay not launching on connection or a black screen when connected Voice prompts that skip or have short pauses while directions are being provided
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: COMMUNICATION:MANUFACTURER TELEMATICS · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2021 Escape/Corsair vehicles built on or before 30-Mar-2021 and Explorer/Aviator vehicles built on or before 09-Apr-2021 may exhibit a slow fuel fill and/or spit back condition during refueling. This may be due to the design of the fuel tank filler pipe. To correct the condition, follow the Service Procedure to replace the fuel tank filler pipe.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2021 Aviator and 2021 Corsair hybrid vehicles may exhibit charging concerns with the Lincoln Dual-Voltage Charging Cord. Use a 110/120V non-GFI outlet and check to see if the vehicle charges properly with the 220V adapter removed. If the charging cord concern is only present when using the 220V adapter, a complete charge cord replacement may not be needed as the 220V adapter (part number VL5CZ-10B706-B) is available separately at accessories.lincoln.com or through the local Ford Authorized Distributor (FAD). Note that discoloration of the 220V adapter or dual voltage charging cord could indicate a problem with the electrical outlet that's used and should be inspected by a licensed electrician. For further diagnostic assistance, contact Webasto Charging systems, Inc. directly at 888-219-6747 or at evscs@webasto.com.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Mustang/Ranger/Transit Connect, 2020-2021 EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator and 2021 Bronco Sport vehicles with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure to update the accessory protocol interface module (APIM) software.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Aviator vehicles built on or before 01-Aug-2019 may exhibit a symptom where the vehicle only shows 5 pages for presets instead of 6 pages. This may be due to the software in the accessory protocol interface module (APIM) SYNC module. Download and run the APIM Configuration application in the Ford Diagnostic and Repair System (FDRS) scan tool. If asked if the original module is still installed, answer NO. For claiming, use causal part 14G371 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: ELECTRICAL SYSTEM:PROPULSION SYSTEM:CHARGING:MODULE:ACCESSORY · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2021 Navigator and 2020-2022 Aviator vehicles may exhibit a condition where the degrees do not appear in the SYNC screen when adjusting the climate control temperature. This may be due to the SYNC software installed in the accessory protocol interface module (APIM). Engineering is currently developing a software update that is expected in January 2022. Once the software update is available, it will be made available to customers who have enabled SYNC 3 Automatic Updates with their vehicle connected to a Wi-Fi network. Repair appointments should be scheduled for customers in February 2022 who do not receive Automatic Updates. Monitor OASIS for updates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2021 Navigator and Aviator vehicles may exhibit a condition where the degrees do not appear in the SYNC screen when adjusting the climate control temperature. This may be due to the SYNC software installed in the accessory protocol interface module (APIM). Engineering is currently developing a software update that is expected in January 2022. Once the software update is available, it will be made available to customers who have enabled SYNC 3 Automatic Updates with their vehicle connected to a Wi-Fi network. Repair appointments should be scheduled for customers in February 2022 who do not receive Automatic Updates. Monitor OASIS for updates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2021 Navigator and Aviator vehicles may exhibit a condition when setting the climate control temperature where the degrees do not appear in the SYNC screen. This may be due to the SYNC software installed in the accessory protocol interface module (APIM). Engineering is currently developing a software update that is expected in January 2022. Once the software update is available, contact the customer and schedule a follow-up appointment for repair in February 2022. Monitor OASIS for updates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2021 Explorer/Aviator Hybrids, 2021 Corsair Hybrid, 2021 F-150 PowerBoost, and 2021 Mustang Mach-E vehicles may exhibit a no-start with a Stop Safely Now warning message in the instrument panel cluster (IPC). The vehicle may have one or more of the following DTCs P0A23, P0A6F, P0A72, P0A75, P0A71, P0A74, P0A77, P0DFA, P06B1, P0A47, P1A0E set by the secondary on-board diagnostic module C (SOBDMC) or secondary on-board diagnostic module B (SOBDMB). This may be due to a drop in the 12-volt circuit. These DTCs will often occur at vehicle key-on and may be difficult to reproduce. Before replacement of the SOBDMC or SOBDMB, diagnose any low voltage DTCs (P0562, U3003) in other modules in the 12V system. If low voltage (less than 10V) is observed in these DTCs snapshot, diagnose the 12v system first. Refer to Workshop Manual (WSM), Section 418-00.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 21-2046 to update the Issue, Action and Service Procedure. Some 2020 Explorer/Aviator/Police Interceptor Utility vehicles equipped with a 10R60/10R80 automatic transmission may exhibit a harsh engagement/harsh shift/delayed shift with or without an illuminated malfunction indicator lamp (MIL) or diagnostic trouble codes (DTCs) P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6, P07F7, P2700, P2701, P2702, P2703, P2704 and/or P2705 stored in the powertrain control module (PCM). This may be due to sticking valves in the main control valve body. To correct the condition, follow the Service Procedure steps to perform the PCM - Transmission Accelerated Main Control Break In routine for the appropriate clutch(s) and/or overhaul main control valve body.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2021 Explorer/Aviator and 2021 Bronco vehicles may exhibit an illuminated airbag warning indicator with diagnostic trouble code (DTC) B1404:13 and/or B1407:13. This may be due to contamination and relative movement in the connection between the wiring harness and the side airbag. To correct the condition, follow the Service Procedure steps to replace the affected connector with a service pigtail and the affected side airbag.
Source components: AIR BAGS:SENSOR:SIDE IMPACT · ELECTRICAL SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2021 Explorer/Aviator vehicles may exhibit the A/C blowing warm air with DTC P0645 present in the heating ventilation and air conditioning (HVAC) module. This may be due to spread terminal/terminal pushout in wire harness 14290 and on the corresponding pins to the body control module C (BCMC). Before replacement of the BCMC, disconnect all connectors from the BCMC and check the BCMC pins and wire terminals for damage. Refer to Workshop Manual (WSM), Section 419-10. If spread terminals or terminal pushout is present, repair as necessary. Refer to Wiring Diagram, Cell 005 for repair procedures. Reconnect all connections to the BCMC as indicated by the procedure in the Shop manual. Test the function of the A/C to ensure that it is blowing cold air.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:APPLIANCE:AIR CONDITIONER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Mustang/Ranger/Transit Connect, 2020-2021 EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator and 2021 Bronco Sport vehicles with SYNC 3 may experience various SYNC performance related concerns To correct the condition, follow the Service Procedure to update the accessory protocol interface module (APIM) software.
Source components: EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM) · POWER TRAIN:MANUAL TRANSMISSION:INTERNAL:DOGS/SYNCHROS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2021 Explorer/Aviator hybrid vehicles may exhibit a brake pedal pulsation or vibration when the brakes are applied. The customer may state that the anti-locking brake system (ABS) system is activating without any indicators on the instrument panel cluster (IPC). This may be due to the regenerative braking software in the ABS module. To correct the condition, follow the Service Procedure Steps to perform a coordinated flash on the powertrain control module (PCM) and ABS module.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · SERVICE BRAKES, AIR:ANTILOCK:ABS WARNING LIGHT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2021 Explorer/Aviator vehicles may exhibit an inoperative driver switchpack (windows inop, mirror control unresponsive, etc.). DTC B1088:87 may be present in the DDM. To correct the condition perform the Driver Door Module (DDM) configuration application using the Ford diagnostic scan tool. After running the configuration application, perform a window learn routine via the ford diagnostic scan tool. The condition can also be resolved by letting the vehicle enter a deep sleep cycle. Engineering is currently investigating this concern and will be releasing a service fix. Let the customer know they can continue to drive the vehicle and schedule service appointments for customers once the repair becomes available. For claiming, use causal part 14B291 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:BODY CONTROL MODULE/BCM · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2021 Corsair/Nautilus/Navigator/Aviator, 2021 Mustang Mach-E vehicles equipped with Phone-as-a-Key may exhibit Phone-as-a-Key concerns and have diagnostic trouble code(s) (DTC) U200D:15, U200E:15, U200F:15, B15**:31, B15**:49 and/or B15A5:56 stored in the remote function actuator (RFA) module. If the vehicle is exhibiting other symptoms outside of Phone-as-a-key concerns, address those first. If any of these DTCs are detected during diagnostics, clear the DTCs, reflash RFA to the latest software level and start a new Ford Diagnosis and Repair System (FDRS) session. Verify that DTCs are no longer present. If only the B15**:31, B15**:57 and/or B15A5:56 DTC(s) returns in the RFA after a self test, follow normal Workshop Manual (WSM) diagnostics, Section 419-01C.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.