Original record summaries, dates and identifiers for this model-year. Records 601–700 of 713, ordered newest first. Dated records on this page: May 29, 2019–Apr 8, 2020.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Apr 8, 2020Service Bulletin/Repair Instructions
9004249
NHTSA communication ID: 10175616
NHTSA source summary · Original PDF not reviewed by Recallfolio
FRAME, Rear Seat Back, And Cushion Assembly For all 2-door vehicles, if rear seat exhibits one of the following conditions, please call FCA redacted Content prior to repair. Rear Seat Does Not Fold Cannot Remove Seat Seat Cables Stretched/Broken Seat Latch Seized Rear Seat release not working If no answer, please leave a message with dealer contact and VIN information. If no response in 15 minutes, proceed with repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
DAMPER, Steering Additional service procedure steps before replacing the steering damper: Before istalling the steering damper to the vehicle, it is important to prime the new damper by 5 continuous compression ? extension stroke cycles by hand, each cycle consists of a full compression and a full extension stroke, without stops as fast as possible. Use large screwdrivers inserted in the bushings to aid in purging. This will allow you to stand on the lower screwdriver to hold the damper stationary and pump the rod end easier. Perform purge before installing NOTE: Hand purge to be completed in a vertical position with the base cup sticker end down toward the ground and the rod side facing up.See CSN V41 for detail procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Water Pump Inlet Tube Fastener Torque This bulletin involves checking the torque on the water pump inlet tube fasteners to possibly eliminate coolant leak at this location. The customer may describe either a coolant leak or the coolant level is low.
Source components: ENGINE AND ENGINE COOLING · FUEL SYSTEM, GASOLINE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Water Pump Inlet Tube Fastener Torque This bulletin involves checking the torque on the water pump inlet tube fasteners to possibly eliminate coolant leak at this location. The customer may describe either a coolant leak or the coolant level is low.
Source components: ENGINE AND ENGINE COOLING · FUEL SYSTEM, GASOLINE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Water Pump Inlet Tube Fastener Torque This bulletin involves checking the torque on the water pump inlet tube fasteners to possibly eliminate coolant leak at this location. The customer may describe either a coolant leak or the coolant level is low.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
PUMP, Water (Water Pump Inlet Tube) For concern of leak at water pump, please check and re-torque water pump inlet tube fasteners as described in Service Bulletin 07-001-20 before replacing the water pump.
NHTSA source summary · Original PDF not reviewed by Recallfolio
PUMP, Water (Water Pump Inlet Tube) For concern of leak at water pump, please check and re-torque water pump inlet tube fasteners as described in Service Bulletin 07-001-20 before replacing the water pump.
NHTSA source summary · Original PDF not reviewed by Recallfolio
PUMP, Water (Water Pump Inlet Tube) For concern of leak at water pump, please check and re-torque water pump inlet tube fasteners as described in Service Bulletin 07-001-20 before replacing the water pump.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following DTCs have been set:P0456 - EVAP System Small Leak.If DTC P0456 is present use wiTECH Small Leak Verification Test (SLVT) to determine if a leak is present in the system. P0171 - Fuel System 1/1 Lean(LATAM Only). P0172 - Fuel System 1/1 Rich(LATAM Only). P0128 - Thermostat Rationality(APAC&EMEA with Sales Codes NA1 with NBQ or NB6 Only). P050B - Cold Start Ignition Timing Performance(APAC&EMEA with Sales Codes NA1 with NBQ or NB6 Only). Customers may experience:Excessive fan noise when the A/C is on MAX output. Rough idle at engine start up in colder ambient emperatures. Software enhancements include:Electric Vacuum Pump (EVP) update. Fan noise reduction. Low Speed Pre Ignition (LSPI) update.
Source components: BACK OVER PREVENTION · ELECTRICAL SYSTEM · EXTERIOR LIGHTING · FUEL SYSTEM, GASOLINE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following DTCs have been set:P0456 - EVAP System Small Leak.If DTC P0456 is present use wiTECH Small Leak Verification Test (SLVT) to determine if a leak is present in the system. P0171 - Fuel System 1/1 Lean(LATAM Only). P0172 - Fuel System 1/1 Rich(LATAM Only). P0128 - Thermostat Rationality(APAC&EMEA with Sales Codes NA1 with NBQ or NB6 Only). P050B - Cold Start Ignition Timing Performance(APAC&EMEA with Sales Codes NA1 with NBQ or NB6 Only). Customers may experience:Excessive fan noise when the A/C is on MAX output. Rough idle at engine start up in colder ambient emperatures. Software enhancements include:Electric Vacuum Pump (EVP) update. Fan noise reduction. Low Speed Pre Ignition (LSPI) update.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following DTCs have been set:P0456 - EVAP System Small Leak.If DTC P0456 is present use wiTECH Small Leak Verification Test (SLVT) to determine if a leak is present in the system. P0171 - Fuel System 1/1 Lean(LATAM Only). P0172 - Fuel System 1/1 Rich(LATAM Only). P0128 - Thermostat Rationality(APAC&EMEA with Sales Codes NA1 with NBQ or NB6 Only). P050B - Cold Start Ignition Timing Performance(APAC&EMEA with Sales Codes NA1 with NBQ or NB6 Only). Customers may experience:Excessive fan noise when the A/C is on MAX output. Rough idle at engine start up in colder ambient emperatures. Software enhancements include:Electric Vacuum Pump (EVP) update. Fan noise reduction. Low Speed Pre Ignition (LSPI) update.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. The customer may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC):P0456 EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification Test (SLVT) to determine if a leak is present in the system. P061A - Level 2 Torque Performance. P0507 - Idle Speed Performance Higher Than Expected. Customers may also describe the following condition:Excessive fan noise when the A/C is on MAX output. Other enhancements included in this update:Electric vacuum pump (EVP) update. Fan noise reduction.
Source components: ELECTRICAL SYSTEM:SOFTWARE · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SWITCH, Power Window For concern of rear windows INOP from the rear window switch, please contact FCA Redacted Content before replacing the part. If no response in 15 minutes, proceed with repair.
Source components: ELECTRICAL SYSTEM · POWER TRAIN · VISIBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
FRAME, Front Seat Cushion For all 2 door JL vehicles, if the front driver or passenger seat is stuck in the folded (EZ entry) position or it won't return to normal seating position, review SB 23-020-19 prior to replacing the seat frame.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following DTCs have been set:P0456 - EVAP System Small Leak.If DTC P0456 is present use wiTECH Small Leak Verification Test (SLVT)to determine if a leak is present in the system. P0128 - Thermostat Rationality(APAC&EMEA with Sales Codes NA1 with NBQ or NB6 Only). P050B - Cold Start Ignition Timing Performance(APAC&EMEA with Sales Codes NA1 with NBQ or NB6 Only). Customers may experience:Excessive fan noise when the A/C is on MAX output. Rough idle at engine start up in colder ambient temperatures. Software enhancements include:Electric Vacuum Pump (EVP) update. Fan noise reduction. Low Speed Pre Ignition (LSPI) update.
Source components: ELECTRICAL SYSTEM:SOFTWARE · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Rubicon Front Seat Back Panel Loose This bulletin includes inspecting, reattaching and if needed replacing the front seat back panel(s). Customers may comment on the following:Front seat back panel is loose. Front seat back panel fell off. Gap between the seat back and seat assembly,Fig. 1. Gap Between Seat Back and Panel
NHTSA source summary · Original PDF not reviewed by Recallfolio
Body Control Module (BCM) Reconfigure for Enabling the Auto-On Comfort Settings This bulletin involves reconfiguring the BCM and possibly a radio reset, to enable the auto-on comfort settings. Customers may comment on one or more of the following:If below 4 °C (40 °F), the heated seats or heated steering wheel turn on by themselves. If above 26 °C (80 °F), the vented seats turn on by themselves. Cannot turn off the auto-on comfort feature. With the symptom/condition listed above, there?s no setting in the radio to turn the auto-on comfort feature off.
Source components: ELECTRICAL SYSTEM · SEATS:FRONT ASSEMBLY:SEAT HEATER/COOLER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
UJQ Radio Enhancements This bulletin involves inspecting and if required, updating the radio software level to:22.5 Without Digital Audio Broadcasting (Sales Code RS9). 21.10 With RS9. Customers may experience one or more of the following: Arabic language is missing (Without RS9). Navigation inoperable (Without RS9). Bottom menu bar of the radio is non responsive or frozen (Without RS9). After viewing the weather map following a flood advisory popup, the main soft key's at the bottom of the screen may not respond when pressed (Without RS9). Radio will not turn off (Without RS9). Poor AM/FM Reception (Without RS9). Uconnect Live feature may not function properly (EMEA only). Radio may reset, turn off and then back on. Radio display screen freezes. Can freeze in any mode: navigation, audio or backup camera. Audio distortion heard during phone calls and CarPlay®. Rear View Camera (RVC) display screen turns blue or green.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Latch, Quarter Window, Power Sliding Roof Prior to ordering this part for customers that complain about a buzz, squeak, or rattle, please reference the repair information in the service library. Latch rattles can be repaired by applying UHMW tape to the receiver.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Air Suspension Components Star Parts Catalog has been updated to show individual service parts for the compressor assembly. This will allow service technicians to repair the root cause without over repairing the system. Replace only the part deemed failed by the diagnostics performed. Individual parts include: - Compressor - Valve block - Individual hoses - Temp sensor - Shield - Air line clips NOTE: in most situations when a new compressor is needed, the compressor as a separate part is the correct repair, and the assembly would not be required.
NHTSA source summary · Original PDF not reviewed by Recallfolio
FRAME, Front Seat Cushion For all 2 door JL vehicles, if the front driver or passenger seat is stuck in the folded (EZ entry) position or it won't return to normal seating position, please call Ajay Sharma (646) 236-2413 prior to any repairs or teardown. If no response in 15 minutes, proceed with repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Additional Repair Steps After the Steering Gear or Pump was Replaced This bulletin will help to determine if additional repair steps are needed for the steering gear or Electric Hydraulic Power Steering (EHPS) pump replacement.If the EHPS software is updated and the sales code is added without steering gear replacement, this will cause undesirable steering feel. A customer or technician has replaced the steering gear or EHPS pump, for any reason.
NHTSA source summary · Original PDF not reviewed by Recallfolio
UGQ Radio Enhancements This bulletin involves inspecting and if required, updating the radio software level to 28.31. Customers may experience one or more of the following: Navigation screen freezes after a Voice Recognition (VR) command. Warning chime will not turn off. Radio display black, except application bar. Language setting reverting from customer set language to Italian language. Message displayed ?TomTom® live services unavailable?. Frequent pop-ups during startup saying device not connected - Uconnect LIVE. Uconnect Live feature may not function properly. Radio may reset, turn off and then back on. Audio distortion heard during phone calls and CarPlay®. In addition the following enhancements are included:Bluetooth® improvements. VR improvements. Russian language enhancements.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. The customer may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following DTCs:P061A - Level 2 Torque Performance. P0507 - Idle Speed Performance Higher Than Expected. P0456 - EVAP System Small Leak. Customers may also describe the following condition:Excessive fan noise when the A/C is on MAX output. Other enhancements included in this update:Electric vacuum pump (EVP) update. Fan noise reduction.
Source components: ELECTRICAL SYSTEM · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
COVER, Cylinder Head, Left/Right Prior to replacing the cylinder head cover on ANY 3.6L Pentastar Upgrade Engine, verify that there are no steel dowel pins pressed into the cylinder head. If dowels are present in the cylinder head please remove carefully without touching/damaging the cylinder head sealing surface.
NHTSA source summary · Original PDF not reviewed by Recallfolio
WIRING KIT, Enclosure (Mopar JL hard top conversion accessory kit) The HVAC control panel requires replacement when GTP sales code is present to restore rear defrost function. The switch is not provided in this kit and a service replacement part must be ordered. See service information procedure for switch replacement and below chart for replacement part numbers. vehicle has GTP+BNH+HAA replace HVAC control with pn 6BE36TRMAC vehicle has GTP+BNH-HAA replace HVAC control with pn 6BE37TRMAC vehicle has GTP+HAA-BNH replace HVAC control with pn 6BE40TRMAC vehicle has GTP-HAA-BNH replace HVAC control with pn 6BE41TRMAC Please ensure that the proper color code is used in place of the part TRM designation. For any questions call John Altsman at (248) 512-9361.
NHTSA source summary · Original PDF not reviewed by Recallfolio
DAMPER, Steering Additional service procedure steps after replacing the steering damper: Verify the correct orientation of the steering damper. With the vehicle on the ground, it is required to turn the steering wheel for five lock to lock turns ( ?Full Left ? Full Right ? Center? OR ?Full Right ? Full Left ? Center? counted as 1) at 1 rotation/sec to prime the steering damper and purge out the air. NOTE: It is important to prime the new damper by rotating the steering wheel five full lock to lock turns to purge any trapped air out.
NHTSA source summary · Original PDF not reviewed by Recallfolio
WIRING KIT, Enclosure (Mopar JL hard top conversion accessory kit) The HVAC control panel requires replacement when GTP sales code is present to restore rear defrost function. The switch is not provided in this kit and a service replacement part must be ordered. See service information procedure for switch replacement and below chart for replacement part numbers. vehicle has GTP+BNH+HAA replace HVAC control with pn 6BE36TRMAC vehicle has GTP+BNH-HAA replace HVAC control with pn 6BE37TRMAC vehicle has GTP+HAA-BNH replace HVAC control with pn 6BE40TRMAC vehicle has GTP-HAA-BNH replace HVAC control with pn 6BE41TRMAC Please ensure that the proper color code is used in place of the part TRM designation. For any questions call John Altsman at (248) 512-9361.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:APPLIANCE:AIR CONDITIONER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
DAMPER, Steering Additional service procedure steps after replacing the steering damper: Verify the correct orientation of the steering damper. With the vehicle on the ground, it is required to turn the steering wheel for five lock to lock turns ( ?Full Left ? Full Right ? Center? OR ?Full Right ? Full Left ? Center? counted as 1) at 1 rotation/sec to prime the steering damper and purge out the air. NOTE: It is important to prime the new damper by rotating the steering wheel five full lock to lock turns to purge any trapped air out.
NHTSA source summary · Original PDF not reviewed by Recallfolio
UAQ Radio Enhancements This bulletin involves inspecting and if required, updating the radio software level to 28.3. Customers may experience one or more of the following:Application bar displays but the screen is black. Continuous chimes from the radio. Voice Recognition (VR) not recognizing voice. Bluetooth connection issues. Navigation screen freezes after a VR command. Intermittent operation of the remote services after vehicle has been turned off for 30 minutes or more. Off road App is missing. Rear View Camera (RVC) display screen turns blue or green. Audio quality Improvement in hands-free calling using Car Play, Android Auto or Bluetooth. Radio will continuously reset with the Jeep splash screen. Radio intermittently resetting or not booting up. Intermittent operation of the vehicle finder app. App icons at the bottom of the display freezes, touch screen will not respond. Radio may reset, turn off and then back on. Audio distortion heard during phone calls and CarPlay. In addition, the following enhancements are also included in this update:Bluetooth improvements. VR improvements.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
NHTSA source summary · Original PDF not reviewed by Recallfolio
UAQ Radio Enhancements This bulletin involves inspecting and if required, updating the radio software level to 28.3. Customers may experience one or more of the following:Application bar displays but the screen is black. Continuous chimes from the radio. Voice Recognition (VR) not recognizing voice. Bluetooth connection issues. Navigation screen freezes after a VR command. Intermittent operation of the remote services after vehicle has been turned off for 30 minutes or more. Off road App is missing. Rear View Camera (RVC) display screen turns blue or green. Audio quality Improvement in hands-free calling using Car Play, Android Auto or Bluetooth. Radio will continuously reset with the Jeep splash screen. Radio intermittently resetting or not booting up. Intermittent operation of the vehicle finder app. App icons at the bottom of the display freezes, touch screen will not respond. Radio may reset, turn off and then back on. Audio distortion heard during phone calls and CarPlay. In addition, the following enhancements are also included in this update:Bluetooth improvements. VR improvements.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Shimmy In The Steering Wheel After Hitting An Irregularity On The Road Surface This bulletin involves discussing an available video instructing the technicians on how to properly diagnosis and repair this issue.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Authentic Mopar® Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar® Glass.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CAMERA, Rear View For concerns of back up camera flicker/blank/blue/black screen or camera inop, please ensure Radio is at latest software level. After update, system requires three sleep cycles to function properly. Please verify camera LVDS cable connection at camera and radio head unit. Also verify harness connection between high mounted stop lamp and body harness for bent pins or loose connection at XY310A, XY485A. Please create and send a copy of the vehicle scan report and specify radio SW version and radio head unit ID to Bing Guo and Rafay Adil via email bingruo.guo@fcagroup.com (248) 500-7355 rafay.adil@fcagroup.com (248) 736-7059 Please call for any additional questions or assistance needed. If no response in 15 minutes, proceed with repair. Please be sure to attach a copy of the Vehicle Scan Report on the repair order.
Source components: BACK OVER PREVENTION · PARKING BRAKE · STRUCTURE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Shimmy In The Steering Wheel After Hitting An Irregularity On The Road Surface This bulletin involves discussing an available video instructing the technicians on how to properly diagnosis and repair this issue.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Authentic Mopar® Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar® Glass.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CAMERA, Rear View For concerns of back up camera flicker/blank/blue/black screen or camera inop, please ensure Radio is at latest software level. After update, system requires three sleep cycles to function properly. Please verify camera LVDS cable connection at camera and radio head unit. Also verify harness connection between high mounted stop lamp and body harness for bent pins or loose connection at XY310A, XY485A. Please create and send a copy of the vehicle scan report and specify radio SW version and radio head unit ID to Bing Guo and Rafay Adil via email bingruo.guo@fcagroup.com (248) 500-7355 rafay.adil@fcagroup.com (248) 736-7059 Please call for any additional questions or assistance needed. If no response in 15 minutes, proceed with repair. Please be sure to attach a copy of the Vehicle Scan Report on the repair order.
Source components: BACK OVER PREVENTION · BACK OVER PREVENTION: SENSING SYSTEM: CAMERA · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technicianmay find one or more of the following Diagnostic Trouble Codes (DTCs):P06EF - Engine Restart Performance. P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification test (SLVT)to determine if a leak is present in the system. Customers may experience one or more of the following:Excessive blower fan noise when the A/C is on MAX output. Intermittentrough idle or idle surging, when coming to a stop(Automatic transmission equipped vehicles only). Random Electronic Stability Control (ESC) lamp illuminates in the InstrumentPanel Cluster (IPC). Driving at vehicle speeds while in first gear and shifting into neutral, amessage "Shift to 1st gear not allowed" message appears in the Electronic Vehicle Information Center (EVIC) when conditions are not met(Manual transmission equipped vehicles only). 3 km (2 mph) difference between cruise set speed versus actual displayspeed. During cold vehicle operation and the use of cruise control on vehicles equipped with an automatic transmission, the engine RPMs may dropbelow idle speed while cruise control is engaged, this may occur if the customer presses the accelerator pedal to achieve a vehicle speedgreater than the cruise control speed and then releasing it. Radio or IPC may reboot (flash off/flash on) during an Engine Stop Start(ESS) shutdown in cold conditions with a battery temperature below -12°C (10°F).
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technicianmay find one or more of the following Diagnostic Trouble Codes (DTCs):P06EF - Engine Restart Performance. P0456 - EVAP System Small Leak.If DTC P0456 is present use the wiTECH Small Leak Verification test (SLVT)to determine if a leak is present in the system. Customers may experience one or more of the following:Excessive blower fan noise when the A/C is on MAX output. Intermittentrough idle or idle surging, when coming to a stop(Automatic transmission equipped vehicles only). Random Electronic Stability Control (ESC) lamp illuminates in the InstrumentPanel Cluster (IPC). Driving at vehicle speeds while in first gear and shifting into neutral, amessage "Shift to 1st gear not allowed" message appears in the Electronic Vehicle Information Center (EVIC) when conditions are not met(Manual transmission equipped vehicles only). 3 km (2 mph) difference between cruise set speed versus actual displayspeed. During cold vehicle operation and the use of cruise control on vehicles equipped with an automatic transmission, the engine RPMs may dropbelow idle speed while cruise control is engaged, this may occur if the customer presses the accelerator pedal to achieve a vehicle speedgreater than the cruise control speed and then releasing it. Radio or IPC may reboot (flash off/flash on) during an Engine Stop Start(ESS) shutdown in cold conditions with a battery temperature below -12°C (10°F).
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
UCQ Radio Enhancements This bulletin involves inspecting and if required, updating the radio software level to 28.3. Customers may experience one or more of the following:Radio will continuous reset with the Jeep splash screen. App icons at the bottom of the display freezes, touch screen will not respond. Radio may reset, turn off and then back on. Audio distortion heard during phone calls and CarPlay®. Rear View Camera (RVC) display screen turns blue or green. Off Road App is missing. In addition, the following enhancements are included in this update:Bluetooth® improvements. Voice Recognition (VR) improvements.
NHTSA source summary · Original PDF not reviewed by Recallfolio
UAQ Radio Enhancements This bulletin involves inspecting and if required, updating the radio software level to 28.3. Customers may experience one or more of the following:Radio will continuous reset with the Jeep splash screen. App icons at the bottom of the display freezes, touch screen will not respond. Radio may reset, turn off and then back on. Audio distortion heard during phone calls and CarPlay®. Rear View Camera (RVC) display screen turns blue or green. Off Road App is missing. In addition, the following enhancements are included in this update:Bluetooth® improvements. Voice Recognition (VR) improvements.
NHTSA source summary · Original PDF not reviewed by Recallfolio
DOOR, Assembly (Front or Rear) For concern of flag nut not aligned to hole, use a blunt tool and lightly tap on the flag nut to knock it loose from e-coat that has dried it in place.
NHTSA source summary · Original PDF not reviewed by Recallfolio
FRAME, Front Seat Back For JL and JT vehicles with concern of front seat back appears loose at inboard (closest to center console) side hinge, please call Ajay Sharma at (646) 236-2413 prior to any repairs. If no response in 15 mins,proceed with repairs.
NHTSA source summary · Original PDF not reviewed by Recallfolio
HANDLE AND CABLE, Seat Release If you have a 2 door JL with EZ entry handle that is loose or appears broken follow the procedure below. Mounting bracket has grease present which may have damaged plastic part. Please call Adam Rose (586) 804-4315) for cleaning procedure prior to replacing any parts. If no response in 15 minutes, proceed with repair after thoroughly cleaning grease off metal mounting bracket as follows. Clean metal mounting bracket with brake cleaner sprayed onto shop rag, rub on mounting surface until grease is removed. Do not spray brake cleaner directly onto seat. Replacement plastic part may fail in same way if grease is not removed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Pentastar Upgrade Oil Fill Level after an Oil Change This bulletin involves rechecking the oil fill level after filling the engine to the correct specifications. The customer may describe that after an oil change they check their oil fill level and it is showing overfilled on the oil dipstick.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Radio and Back-up Camera Enhancements This bulletin involves updating the radio software level to 1848.24. Customers may experience one or more of the following: Green horizontal lines on back up display, in reverse (If this is the customer concern use camera LOP 18-60-02-Y7, on JL vehicles only). Ghost Touch, features, modes and App?s changing, without drivers input. Speaker pop noise when using Bluetooth device. When vehicle is first started the radio will reset and the time display shows 12:00. Audio distortion and volume fluctuation. Blank rear camera image in reverse (If this is the customer concern use camera LOP 18-60-02-Y7) JL only. Audio cutting in and out during memory recall. Ring tone too loud. AM/FM volume fluctuates. While in CarPlay® or AndroidAuto® Google® maps showing wrong location. Phone disconnected after first call. Black screen or White screen with vertical lines. PIN clear and volume locked while KeySense is used. Audio static while in SXM/SAT modes. Echo heard during Bluetooth phone calls. The radio is locked up. The radio remains on after ignition has been turned off. The radio resets. The radio screen turns black. The radio screen shows messages ?Software Update? or ?Reinsert USB Device? and displays that screen in a continuous loop.
Source components: BACK OVER PREVENTION · ELECTRICAL SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
RADIO [RES] - New and/or Service Exchange For RES radio concerns. Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Idle Related Components For concern of P0507 diagnostic trouble code, please verify the powertrain control module is at the latest software level prior to replacing any components related to P0507 diagnostics.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SWITCH, Neutral Safety If you are working on a Manual Transmission and are considering replacing the Neutral Safety Switch for an Auto Start/Stop Issue, Prior to order/replace please first check operation of the SENSOR; Clutch Pedal and SWITCH, Clutch Starter Interlock. If you have any question, contact Jeff Laduke at (810) 422-3099. If no response in 15 minutes, proceed with repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SENSOR, Clutch Pedal Engineering is seeking information regarding P083F - Clutch Pedal Sensor A B Correlation Faults. Prior to component(s) replacement: Please Contact the following individuals: Joe Marigold (248) 701-8510 / joe.marigold@fcagroup.com Michael Lai (734) 286-0321 / michael.lai@fcagroup.com If no response in 15 minutes, proceed with repair
Source components: POWER TRAIN:CLUTCH ASSEMBLY:PEDAL/HAND LEVER(MOTORCYCLE).
NHTSA source summary · Original PDF not reviewed by Recallfolio
ARMREST, Console If you are replacing a center console armrest for a latch issue, please note that the latch and latch cover are serviceable components. Please only replace the following part numbers for this issue: Latch: 68470797A$ Cover: 68470798A$ Failure to follow this could result in a chargeback