2011 Jeep GRAND CHEROKEE Manufacturer communications & TSBs.Page 1
Original record summaries, dates and identifiers for this model-year. Records 1–100 of 197, ordered newest first. Dated records on this page: Oct 15, 2014–Sep 10, 2026.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Sep 10, 2026Service Bulletin/Repair Instructions
9100897Rev1
NHTSA communication ID: 11037351
NHTSA source summary · Original PDF not reviewed by Recallfolio
Qudra Lift Reman Compressor Excessive Repairs on Quadra Lift Reman Compressors Part Numbers: 68041137AF / R8572790AA / 68087233AA / 52124932AE / 52124934AE / 68064343AC Purpose The Star Parts Catalog has been updated to support component-level repair of the Quadra-Lift air suspension system. Replace only the component confirmed failed through diagnostics. Avoid replacing the complete assembly when an individual service component can correct the concern. Available Service Components Part Number Description R8572790AA Air Suspension Compressor 68087233AA Air Suspension Valve Block 52124932AE Front Air Suspension Hose Assembly 52124934AE Rear Air Suspension Hose Assembly 68064343AC Air Suspension Reservoir 68087240AA Temperature Sensor 68041137AF Compressor Assembly Diagnostic Decision Tree Customer Complaint: Service Air Suspension Message / Sagging / Unable to Adjust Ride Height / Compressor Running Continuously. Step 1: Retrieve and record all DTCs. C15D9 (Low Air Mass): Perform air mass test, complete system fill, leak-down test, and leak source identification before compressor replacement. C15A1 (Unable to Obtain Desired Ride Height): Verify ride height, perform leak-down test, inspect valve block, air lines, and air springs. C1562-98 (Over Temperature): Inspect for excessive compressor run time, leaks, low air mass, and restrictions before condemning the compressor. If a leak is found, repair the leak and verify operation before replacing the compressor. If no leak is found, perform compressor functional evaluation. If moisture is in the lines and valve block, then evacuate or replace lines. Only replace the compressor when a defect is verified (internal leak, failed solenoid, weak output, seized motor, failed functional test, or electrical failure). Service Component Selection Guide Verified Root Cause Recommended Repair Compressor Internal Failure Replace Compressor Valve Block Failure Replace Valve Block Air Line Leak Replace Air Line Air Spring Leak Replace Air Spring Temperature Sensor Failure Replace Temperature Sensor Technician Reminder Replace only the component confirmed failed through diagnostics. In many cases, compressor replacement is not required when the root cause is an air leak, valve block issue, airline concern, or sensor fault.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Qudra Lift Reman Compressor Excessive Repairs on Quadra Lift Reman Compressors Part Numbers: 68041137AF / R8572790AA / 68087233AA / 52124932AE / 52124934AE / 68064343AC Purpose The Star Parts Catalog has been updated to support component-level repair of the Quadra-Lift air suspension system. Replace only the component confirmed failed through diagnostics. Avoid replacing the complete assembly when an individual service component can correct the concern. Available Service Components Part Number Description R8572790AA Air Suspension Compressor 68087233AA Air Suspension Valve Block 52124932AE Front Air Suspension Hose Assembly 52124934AE Rear Air Suspension Hose Assembly 68064343AC Air Suspension Temperature Sensor 68041137AF Service Components Reference Diagnostic Decision Tree Customer Complaint: Service Air Suspension Message / Sagging / Unable to Adjust Ride Height / Compressor Running Continuously. Step 1: Retrieve and record all DTCs. C15D9 (Low Air Mass): Perform air mass test, complete system fill, leak-down test, and leak source identification before compressor replacement. C15A1 (Unable to Obtain Desired Ride Height): Verify ride height, perform leak-down test, inspect valve block, air lines, and air springs. C1562-98 (Over Temperature): Inspect for excessive compressor run time, leaks, low air mass, and restrictions before condemning the compressor. If a leak is found, repair the leak and verify operation before replacing the compressor. If no leak is found, perform compressor functional evaluation. If moisture is in the lines and valve block, then evacuate or replace lines. Only replace the compressor when a defect is verified (internal leak, failed solenoid, weak output, seized motor, failed functional test, or electrical failure). Service Component Selection Guide Verified Root Cause Recommended Repair Compressor Internal Failure Replace Compressor Valve Block Failure Replace Valve Block Air Line Leak Replace Air Line Air Spring Leak Replace Air Spring Temperature Sensor Failure Replace Temperature Sensor Technician Reminder Replace only the component confirmed failed through diagnostics. In many cases, compressor replacement is not required when the root cause is an air leak, valve block issue, airline concern, or sensor fault.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Verify Reman part number availability. Order the "R" part number for all orders: Warranty, Mopar, customer pay and service contract. Order "68" part number for New unsold units only.
NHTSA source summary · Original PDF not reviewed by Recallfolio
HEADREST Incoming Vehicles with Deployed Active Head Rest (AHR) should have a through enquiry. If there is no Broken Pieces or Electrical failure, Direction to follow the RESET Procedure in service Library to RESET the AHR
NHTSA source summary · Original PDF not reviewed by Recallfolio
Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Lubrication and Maintenance Fluids If MOPAR fluids and chemicals are not readily available, please review Service Library for specifications so a suitable alternative can be used
NHTSA source summary · Original PDF not reviewed by Recallfolio
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
NHTSA source summary · Original PDF not reviewed by Recallfolio
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
NHTSA source summary · Original PDF not reviewed by Recallfolio
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
NHTSA source summary · Original PDF not reviewed by Recallfolio
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
Source components: STRUCTURE · STRUCTURE:INTERIOR PANELS:DOOR · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customer complaints may include abnormal engine noise, rough idle, lack of power, misfire. Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customer complaints may include abnormal engine noise, rough idle, lack of power, misfire. Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.
Source components: ENGINE AND ENGINE COOLING:ENGINE:CRANK/CAMSHAFT POSITION SENSOR · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customer complaints may include abnormal engine noise, rough idle, lack of power, misfire. Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.
Source components: ENGINE · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customer complaints may include abnormal engine noise, rough idle, lack of power, misfire. Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.
Source components: ENGINE AND ENGINE COOLING:ENGINE:CRANK/CAMSHAFT POSITION SENSOR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customer complaints may include abnormal engine noise, rough idle, lack of power, misfire. Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Active Head Restraint (AHR) Inadvertent Deployment - X92 Warranty Extension This bulletin involves inspecting the sled bracket striker pin and possibly replacing a front seat AHR that has inadvertently deployed. Customers may comment on the following:The AHR is deployed on one or both front seats and will not reset.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Active Head Restraint (AHR) Inadvertent Deployment - X88 Warranty Extension This bulletin involves inspecting the sled bracket striker pin and possibly replacing a front seat AHR that has inadvertently deployed. Customers may comment on the following:The AHR is deployed on one or both front seats and will not reset.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Active Head Restraint (AHR) Inadvertent Deployment - X88 Warranty Extension This bulletin involves inspecting the sled bracket striker pin and possibly replacing a front seat AHR that has inadvertently deployed. Customers may comment on the following:The AHR is deployed on one or both front seats and will not reset.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Active Head Restraint (AHR) Inadvertent Deployment - X88 Warranty Extension This bulletin involves inspecting the sled bracket striker pin and possibly replacing a front seat AHR that has inadvertently deployed. Customers may comment on the following:The AHR is deployed on one or both front seats and will not reset.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Leather Instrument Panel (IP) Cover Delaminating - X81 Warranty Extension This bulletin involves replacing upper leather IP covers that have suffered delamination issues. Customers may comment on the following:The upper leather IP cover is delaminating or separating.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Leather Instrument Panel (IP) Cover Delaminating - X81 Warranty Extension This bulletin involves replacing upper leather IP covers that have suffered delamination issues. Customers may comment on the following:The upper leather IP cover is delaminating or separating.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Leather Instrument Panel (IP) Cover Delaminating - X81 Warranty Extension This bulletin involves replacing upper leather IP covers that have suffered delamination issues. Customers may comment on the following:The upper leather IP cover is delaminating or separating.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Leather Instrument Panel (IP) Cover Delaminating - X81 Warranty Extension This bulletin involves replacing upper leather IP covers that have suffered delamination issues. Customers may comment on the following:The upper leather IP cover is delaminating or separating.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Charging System, Battery Diagnostic Tools and Warranty This information only bulletin discusses using the correct test equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Leather Instrument Panel (IP) Cover Delaminating - X81 Warranty Extension This bulletin involves replacing upper leather IP covers that have suffered delamination issues. Customers may comment on the following:The upper leather IP cover is delaminating or separating.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Leather Instrument Panel (IP) Cover Delaminating - X81 Warranty Extension This bulletin involves replacing upper leather IP covers that have suffered delamination issues. Customers may comment on the following:The upper leather IP cover is delaminating or separating.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Leather Instrument Panel (IP) Cover Delaminating - X81 Warranty Extension This bulletin involves replacing upper leather IP covers that have suffered delamination issues. Customers may comment on the following:The upper leather IP cover is delaminating or separating.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Leather Instrument Panel (IP) Cover Delaminating - X81 Warranty Extension This bulletin involves replacing upper leather IP covers that have suffered delamination issues. Customers may comment on the following:The upper leather IP cover is delaminating or separating.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Air Suspension Components Star Parts Catalog has been updated to show individual service parts for the compressor assembly. This will allow service technicians to repair the root cause without over repairing the system. Replace only the part deemed failed by the diagnostics performed. Individual parts include: - Compressor - Valve block - Individual hoses - Temp sensor - Shield - Air line clips NOTE: in most situations when a new compressor is needed, the compressor as a separate part is the correct repair, and the assembly would not be required.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Authentic Mopar® Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar® Glass.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Authentic Mopar® Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar® Glass.
NHTSA source summary · Original PDF not reviewed by Recallfolio
RADIO [RES] - New and/or Service Exchange For RES radio concerns. Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Oil Filter Adapter If replacing Oil Filter Adapter due to oil leak, please be aware a seal kit is available for repair. If replacing due to missing Spring Loaded Check Valve, a replacement spring and check valve are now available through MOPAR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Failure Code Change This bulletin involves notifying the dealers and technicians of a change to the Required Flash (RF) and Customer Concern (CC) failure codes.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Oil Pump Assembly If error code P06DD present on any Pentastar V6 application, please inspect oil pump for relief valve failure. See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system
NHTSA source summary · Original PDF not reviewed by Recallfolio
Oil Pump Assembly If error code P06DD present on any Pentastar V6 application, please inspect oil pump for relief valve failure. See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system
NHTSA source summary · Original PDF not reviewed by Recallfolio
Steering Column If vehicle comes in for steering column replacement, verify column installed. Go to Info Column in Star Parts and open the flow chart to determine which column is installed. If column is Daimler, verify that a replacement Daimler column is in stock and use for replacement. If no Daimler column is in stock, replacement must use Presta column (which require a number of other components to be replaced). For more information and details on PN's, see W-Series Flowchart in Star Parts. Contact parts specifying for assistance regarding correct part numbers, for technical assistance contact Star. UPDATE: 11/9/2016 If the new bearing does not fit through the double dash, you need to replace the lower double dash panel to the latest level. Please see the updated flowchart in StarParts for the correct replacement panel.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Steering Column If vehicle comes in for steering column replacement, verify column installed. Go to Info Column in Star Parts and open the flow chart to determine which column is installed. If column is Daimler, verify that a replacement Daimler column is in stock and use for replacement. If no Daimler column is in stock, replacement must use Presta column (which require a number of other components to be replaced). For more information and details on PN's, see W-Series Flowchart in Star Parts. Contact parts specifying for assistance regarding correct part numbers, for technical assistance contact Star.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Seat Shields For vehicles built prior to 5/2/2011:~ Replace old shield (1UN79TRMAA) with new shield (1XN97TRMAA) and bracket (68100737AA).~ Replace old shield (1UP58TRMAA) with new shield (1XN08TRMAA) and bracket (68100737AA).~ Replace old shield (1UQ14TRMAA) with new shield (1XN96TRMAA) and bracket (68100737AA).~ The new bracket (68100737AA) is only needed if the vehicle doesn't already have it (check PN on phyical part)
Source components: STRUCTURE:FRAME AND MEMBERS:UNDERBODY SHIELDS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Steering Column If vehicle comes in for steering column replacement, verify column installed. Go to Info Column in Star Parts and open the flow chart to determine which column is installed. If column is Daimler, verify that a replacement Daimler column is in stock and use for replacement. If no Daimler column is in stock, replacement must use Presta column (which require a number of other components to be replaced). For more information and details on PN's, see W-Series Flowchart in Star Parts. Contact parts specifying for assistance regarding correct part numbers, for technical assistance contact Star.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Seat Shields For vehicles built prior to 5/2/2011:~ Replace old shield (1UN79TRMAA) with new shield (1XN97TRMAA) and bracket (68100737AA).~ Replace old shield (1UP58TRMAA) with new shield (1XN08TRMAA) and bracket (68100737AA).~ Replace old shield (1UQ14TRMAA) with new shield (1XN96TRMAA) and bracket (68100737AA).~ The new bracket (68100737AA) is only needed if the vehicle doesn't already have it (check PN on phyical part)
NHTSA source summary · Original PDF not reviewed by Recallfolio
PSU Exhaust Phaser 05048043AB If replacing the Exhaust Phaser for the following codes: P0340 Cam Missing/Camshaft Sensor Circuit and/or P0345 Cam Missing/Camshaft Sensor Circuit Engineering is requesting that all three Valve Timing components (Phaser, Actuator, OCV) be replaced.~ Please label the components of which bank they came from prior to parts return. ~ Phaser 05048043AB Actuator 05048045AB OCV 05048044AB Please call Joe Lovell at cell (734) 309-6467 with any questions If a response is not received within 15 mins , then proceed with diagnostics/repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
RES / RHA / REB radio that supports Bluetooth and Hands-Free For issues with Bluetooth, Hands-Free Calling, and/or Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT:ELECTRICAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
RES / RHA / REB radio that supports Bluetooth and Hands-Free For issues with Bluetooth, Hands-Free Calling, and/or Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)
NHTSA source summary · Original PDF not reviewed by Recallfolio
Chirping Or Squeaking Coming From The Second Row Headrest This bulletin involves applying lubricant to the headrest mechanism and seat back panel crossmember. Customers may describe a chirping or squeaking coming from the rear second row seat headrest(s) while driving.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Chirping Or Squeaking Coming From The Second Row Headrest This bulletin involves applying lubricant to the headrest mechanism and seat back panel crossmember. Customers may describe a chirping or squeaking coming from the rear second row seat headrest(s) while driving.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Hands Free Module Prompts Begin Erroneously This bulletin involves diagnosing and based on outcome, either performing a USB flash or replacing the Mopar accessory Hands Free Module (HFM). A customer may experience the Uconnect prompts begin to play without pressing the Voice Recognition (VR) button. The prompt may repeat itself two or three times before exiting. The customer satisfaction enhancements are included with this software release. NOTE: After the HFM has been updated it will receive these enhancements: · Reduced ?Device Reading? wait time after connecting a device to the remote USB port. · Call / dial separation improves upon names being recognized as phone numbers. · Improved sound quality during Bluetooth streaming. · Increased iPod and iPhone compatibility. · SMS messaging support via Mobile Application Part (MAP) protocol (not all phones support the MAP protocol). · Added ?None of These? and ?Correction? to the phone book prompt menu for better handling of similar names. · Previous button will return the song currently being played to the beginning of the track. · AirPlay feature ?Dock Connector? no longer needs to be manually selected on Apple devices. This will resolve the ?No Audio? condition when the device is connected to the remote USB port and dock connector is not selected. NOTE: USB mode resume will no longer 'resume' after ignition is OFF.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NAG1 (5A580) Valve Body As per Warranty Bulletin D-13-22, please use R2108213A$ valve body for all Warranty (W), Mopar (M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~
NHTSA source summary · Original PDF not reviewed by Recallfolio
Front Brake Squeak/Squeal Noise This bulletin involves replacing the front brake caliper guide pin bushings. The customer may describe a front brake squeak/squeal noise at cold temperatures or with cold brakes after sitting. Noise is most prevalent during a low-speed stop with light brake pedal effort.
Source components: SERVICE BRAKES, AIR:DISC:CALIPER · SERVICE BRAKES, HYDRAULIC · SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC:CALIPER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Idler Pulley Noise During Cold Start This bulletin involves replacing the idler pulley. The customer may describe a loud high frequency noise that happens within 20 seconds of engine startup and lasts about 90 seconds intermittently during a cold engine start, approximately 0 degrees C (32 degrees F) and below.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Part Description: Valve Body Assembly Issue Description: Valve body design was changed between 2010MY and 2011MY applications. To prevent mix matching valve bodies and solenoid packs the connectors are color coded.~ Valve bodies with a white connector can be used on 2010, 2009, 2008..., model years. Valve bodies with a gray connector can only be used on 2011, 2012, 2013..., model years.~ Solenoid packs with a white connector are used with 2010, 2009, 2008..., model years. Solenoid packs with a gray connector are used with 2011, 2012, 2013..., model years.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: DTC P0405 / P0406 - MIL Light On This bulletin involves reprogramming the Engine Control Module (ECM) with new software. A small number of customers may report the MIL light is on. On further inspection Diagnostic Trouble Code (DTC), P0405 - EGR POSITION SENSOR CIRCUIT LOW and/or P0406 - EGR POSITION SENSOR CIRCUIT HIGH may be found.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:GAS RECIRCULATION VALVE (EGR VALVE).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Idler Pulley Noise During Cold Start This bulletin involves replacing the idler pulley. The customer may describe a loud high frequency noise that happens within 20 seconds of engine startup and lasts about 90 seconds intermittently during a cold engine start, approximately 0 degrees C (32 degrees F) and below.
NHTSA source summary · Original PDF not reviewed by Recallfolio
MIL Illumination: P0300, P0302, P0304 or P0306 (X56 Warranty Extension) This bulletin involves checking for excessive cylinder leakage and replacing the cylinder head if necessary. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any the following Diagnostic Trouble Codes have been set: P0300- Multiple Cylinder Misfire P0302- Cylinder 2 Misfire P0304- Cylinder 4 Misfire P0306- Cylinder 6 Misfire
NHTSA source summary · Original PDF not reviewed by Recallfolio
MIL Illumination: P0300, P0302, P0304 or P0306 (X56 Warranty Extension) This bulletin involves checking for excessive cylinder leakage and replacing the cylinder head if necessary. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any the following Diagnostic Trouble Codes have been set: P0300- Multiple Cylinder Misfire P0302- Cylinder 2 Misfire P0304- Cylinder 4 Misfire P0306- Cylinder 6 Misfire
NHTSA source summary · Original PDF not reviewed by Recallfolio
MIL Illumination: P0300, P0302, P0304 or P0306 (X56 Warranty Extension) This bulletin involves checking for excessive cylinder leakage and replacing the cylinder head if necessary. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any the following Diagnostic Trouble Codes have been set: P0300- Multiple Cylinder Misfire P0302- Cylinder 2 Misfire P0304- Cylinder 4 Misfire P0306- Cylinder 6 Misfire
NHTSA source summary · Original PDF not reviewed by Recallfolio
Clunk And/Or Bump Felt Through The Steering Wheel Under Moderate Braking And/Or Driving Over Rough Roads This bulletin involves road testing and if necessary replacing the intermediate shaft. Clunk and/or bump felt through the steering wheel under moderate braking or driving over rough roads. This can be caused by spline stick/slip from the intermediate shaft.