Original record summaries, dates and identifiers for this model-year. Records 1–100 of 371, ordered newest first. Dated records on this page: Apr 12, 2022–Aug 25, 2026.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Aug 25, 2026Service Bulletin/Repair Instructions
08-323-26
NHTSA communication ID: 11036745
NHTSA source summary · Original PDF not reviewed by Recallfolio
Service 4WD Light Illuminated Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set the following Diagnostic Trouble Code (DTC): ● C2260-63 - ECU Internal Performance - Circuit Component Protection Time-Out Customers may also comment on the following: ● Service 4WD indicator is illuminated.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Radio Message "Power Surge On USB Detected" Customers may comment on the following: ● The radio displays the message: “Power surge on USB hub detected” Fig. 1. NOTE: After the message appears, no USB devices function in the hub (no charging, no data). NOTE: Hub operation does not return until the vehicle undergoes a full key cycle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Radio Message "Power Surge On USB Detected" Customers may comment on the following: ● The radio displays the message: “Power surge on USB hub detected” Fig. 1. NOTE: After the message appears, no USB devices function in the hub (no charging, no data). NOTE: Hub operation does not return until the vehicle undergoes a full key cycle
NHTSA source summary · Original PDF not reviewed by Recallfolio
Radio Message "Power Surge On USB Detected" Customers may comment on the following: ● The radio displays the message: “Power surge on USB hub detected” Fig. 1. NOTE: After the message appears, no USB devices function in the hub (no charging, no data). NOTE: Hub operation does not return until the vehicle undergoes a full key cycle
NHTSA source summary · Original PDF not reviewed by Recallfolio
Rear Taillamp Condensation Clearing Procedure On occasion, vehicle exterior taillamp assemblies get fogged with a light layer of condensation on the SYMPTOM: inside of the lenses Fig. 1. This may be reported after the lamps have been turned on and brought up to operating temperature, turned off and then rapidly cooled by cold water (such as rain, or the water from a vehicle wash). Lens fogging can also occur under certain atmospheric conditions after a vehicle has been parked outside overnight (i.e. a warm humid day followed by clear cool night). This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the taillamps on will usually accelerate this process. This bulletin is to communicate the procedure for rear taillamp condensation clearing.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Servicing the stabilizer bar links for Jeep Compass: If bar links need to be replaced, make sure both ends are metal. Do not mix metal and plastic ends on same bar. If replacing existing metal end, only that end can be replaced with new metal end.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Jeep Compass built prior to Jan 4, 2021, when servicing the stabilizer bar links. If bar links need to be replaced, make sure both ends are metal. Do not mix metal and plastic ends on same bar. If replacing existing metal end, only that end can be replaced with new metal end.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
NHTSA source summary · Original PDF not reviewed by Recallfolio
Before replacing the RDM, please be aware that NVH from differential gears is typical and within the acceptable limits. Do not replace RDM for NVH issue.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Rear Taillamp Condensation Clearing Procedure On occasion, vehicle exterior taillamp assemblies get fogged with a light layer of condensation on the SYMPTOM: inside of the lenses Fig. 1. This may be reported after the lamps have been turned on and brought up to operating temperature, turned off and then rapidly cooled by cold water (such as rain, or the water from a vehicle wash). Lens fogging can also occur under certain atmospheric conditions after a vehicle has been parked outside overnight (i.e. a warm humid day followed by clear cool night). This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the taillamps on will usually accelerate this process. This bulletin is to communicate the procedure for rear taillamp condensation clearing.
Source components: ELECTRICAL SYSTEM · STRUCTURE:BODY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
NHTSA source summary · Original PDF not reviewed by Recallfolio
Verify "Z" part number availability. Order a "Z" part number for all Exchange Orders: Warranty, Mopar, Customer pay and Service contract. Order"68" part number for New unsold units only
NHTSA source summary · Original PDF not reviewed by Recallfolio
948TE Transmission Reaction Shaft Service Bushing Kit Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): ● P1DB7-00 - Torque Converter Clutch Performance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates
NHTSA source summary · Original PDF not reviewed by Recallfolio
Rear Taillamp Condensation Clearing Procedure On occasion, vehicle exterior taillamp assemblies are fogged with a light layer of condensation on the inside of the lenses Fig. 1. This may be reported after the lamps have been turned on and brought up to operating temperature, turned off and then rapidly cooled by cold water (such as rain, or the water from a vehicle wash). Lens fogging can also occur under certain atmospheric conditions after a vehicle has been parked outside overnight (i.e. a warm humid day followed by clear cool night). This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the taillamps on will usually accelerate this process. This bulletin is to communicate the procedure for rear taillamp condensation clearing.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
NHTSA source summary · Original PDF not reviewed by Recallfolio
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Verify current warranty policy to determine if digital imaging pre-authorization is required or pre-approval is required from the Regional Office; depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Management Procedure for Customer Issues in Connected Services Customers may experience the following: ● Various Connected Services issues. The purpose of this informative Technical Service Bulletin (TSB) is to support the Network on the following topics: ● Discern the different kinds of connected service issues (onboard / offboard). ● Support the customer in his journey to open a request via Customer Care. ● Address on the correct actions to properly manage a customer complaining about the received assistance."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Rear Taillamp Condensation Clearing Procedure On occasion, vehicle exterior taillamp assemblies are fogged with a light layer of condensation on the inside of the lenses Fig. 1. This may be reported after the lamps have been turned on and brought up to operating temperature, turned off and then rapidly cooled by cold water (such as rain, or the water from a vehicle wash). Lens fogging can also occur under certain atmospheric conditions after a vehicle has been parked outside overnight (i.e. a warm humid day followed by clear cool night). This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the taillamps on will usually accelerate this process. This bulletin is to communicate the procedure for rear taillamp condensation clearing."
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On "
NHTSA source summary · Original PDF not reviewed by Recallfolio
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
NHTSA source summary · Original PDF not reviewed by Recallfolio
LIFTER, Hydraulic Roller Deactivating Please do not replace MDS lifters because the disconnecting pin is not lined up, this is normal and not a defect.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Lubrication and Maintenance Fluids If MOPAR fluids and chemicals are not readily available, please review Service Library for specifications so a suitable alternative can be used
NHTSA source summary · Original PDF not reviewed by Recallfolio
HEADLAMP WITHOUT BALLAST,If a replacement D5S BULB is needed, order the following: FOR North America D5S PART NUMBER: L0000D5S FOR Enlarged Europe XF D5S PART NUMBER: 71777147 FOR Enlarged Europe XP D5S PART NUMBER: 1609490380
NHTSA source summary · Original PDF not reviewed by Recallfolio
HEADLAMP WITHOUT BALLAST,If a replacement D5S BULB is needed, order the following: FOR North America D5S PART NUMBER: L0000D5S FOR Enlarged Europe XF D5S PART NUMBER: 71777147 FOR Enlarged Europe XP D5S PART NUMBER: 1609490380
NHTSA source summary · Original PDF not reviewed by Recallfolio
Rear Tail Lamp Condensation Clearing Procedure Some customers may report that on occasion, vehicle exterior tail lamp assemblies are fogged with a light layer of condensation on the inside of the lenses. This may be reported after the lamps have been turned on and brought up to operating temperature, turned off, and then rapidly cooled by cold water (such as rain, or the water from a vehicle wash). This bulletin is to communicate the procedure for rear tail lamp condensation clearing.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Powertrain Control Module (PCM) Updates Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ? P06E9 - Engine Starter Performance (NA Only). ? P0456 - EVAP System Small Leak. NOTE: If DTC P0456 is present use the wiTECH Small Leak Verification Test (SLVT) to determine if a leak is present in the system. ? P141B - Starter Control 1 Circuit Performance. ? P141C - Starter Control 2 Circuit Performance. ? P26E4-64 - Starter Control 2 Circuit Signal Plausibility Failure. ? P0615-64 - Starter Control Circuit Signal Plausibility Failure. In addition, the customer may notice one or more of the following conditions: ? **A difference in the set cruise control speed and actual speed on the odometer (i.e. driver sets 100 kph (62 mph), vehicle will hit a max of 95 kph (59 mph) and cruise at 95 kph (59 mph)) (Sales Code ED6 Only).** ? Long engine cranking prior to vehicle start, more noticeable when the outside temperature is above 40 °c (104 °f) (EE with Sales Code ED6 Only). ? Vehicle will intermittently not start (South Korea Only). ? Poor fuel economy. ? Slight engine pinging noise while accelerating and poor performance. ? The engine oil dipstick may indicate a low oil level, however the low oil pressure warning indicator does not illuminate in the Instrument Panel Cluster (IPC). ? No crank condition while pushing the start button numerous times, if the vehicle is turned off completely and then restarted, it will start normally. ? Cruise control and adaptive cruise control are inoperable. ? A ?Service Speed Limiter? message in the IPC and Active Vehicle Speed Limiter (AVSL) will be inoperable. NOTE: There will be no stored or active DTCs with this IPC message. This bulletin involves reprogramming the PCM with the latest available software.
Source components: ELECTRICAL SYSTEM · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Powertrain Control Module (PCM) Updates Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ? P06E9 - Engine Starter Performance (NA Only). ? P0456 - EVAP System Small Leak. NOTE: If DTC P0456 is present use the wiTECH Small Leak Verification Test (SLVT) to determine if a leak is present in the system. ? P141B - Starter Control 1 Circuit Performance. ? P141C - Starter Control 2 Circuit Performance. ? P26E4-64 - Starter Control 2 Circuit Signal Plausibility Failure. ? P0615-64 - Starter Control Circuit Signal Plausibility Failure. In addition, the customer may notice one or more of the following conditions: ? **A difference in the set cruise control speed and actual speed on the odometer (i.e. driver sets 100 kph (62 mph), vehicle will hit a max of 95 kph (59 mph) and cruise at 95 kph (59 mph)) (Sales Code ED6 Only).** ? Long engine cranking prior to vehicle start, more noticeable when the outside temperature is above 40 °c (104 °f) (EE with Sales Code ED6 Only). ? Vehicle will intermittently not start (South Korea Only). ? Poor fuel economy. ? Slight engine pinging noise while accelerating and poor performance. ? The engine oil dipstick may indicate a low oil level, however the low oil pressure warning indicator does not illuminate in the Instrument Panel Cluster (IPC). ? No crank condition while pushing the start button numerous times, if the vehicle is turned off completely and then restarted, it will start normally. ? Cruise control and adaptive cruise control are inoperable. ? A ?Service Speed Limiter? message in the IPC and Active Vehicle Speed Limiter (AVSL) will be inoperable. NOTE: There will be no stored or active DTCs with this IPC message. This bulletin involves reprogramming the PCM with the latest available software.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Radio Over The Air JR34.3 Updating to JR34.32.Software Version Customers may experience one or more of the following: Not be able to use Mobile Wi-Fi upon start up. Hotspot gives a no Internet connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from JR34.3 to JR34.32. NOTE: National launch for this FOTA update is expected to begin February 20, 2023.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Powertrain Control Module (PCM) Updates Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTC)s: **P24D1-00 - Particulate Matter Sensor Regeneration Incomplete. P24AE-00 - Particulate Matter Sensor Circuit. P24B0-00 - Particulate Matter Sensor Circuit Low. P24B1-00 - Particulate Matter Sensor Circuit High. P24B2-00 - Particulate Matter Sensor Circuit Intermittent. P24D0-00 - Particulate Matter Sensor Supply Voltage Circuit Low. P24D3-00 - Particulate Matter Sensor Supply - Circuit Voltage Above Threshold. P24AF-00 - Particulate Matter Sensor Circuit Performance. P24B5-00 - Particulate Matter Sensor Heater Control Circuit Low. P24B6-00 - Particulate Matter Sensor Heater Control Circuit High. P24B7-00 - Particulate Matter Sensor Heater Resistance. P24DA-00 - Particulate Matter Sensor Exhaust Sample Error Bank 1. U05A4-00 - Particulate Matter Sensor Received Invalid Data From ECM - PCM. P2002-00 - DPF Efficiency Based On PM Sensor Monitoring. NOTE: If DTC P2002 is present it will require DPF and PM sensor replacement. Refer to all applicable published service bulletins for detailed repair procedures and labor times regarding Diesel Particulate Matter Sensor (DPM) replacement. U02A3-00 - Loss of Communication with PM Sensor Module.** P24B2-00 - Particulate Matter Sensor Circuit Intermittent (EBS Sales Code only). P20F6-00 - Reductant Injection Valve Stuck Open Bank 1 Unit 1 (EBS Sales Code only). P208E-00 - Reductant Injector Stuck Closed - Bank 1 Unit 1 (EBS Sales Code only). Customers may also experience one or more of the following: The Engine Stop/Start (ESS) system remains in the last used state and does not default back to ON for each key cycle as designed (Vehicles on the RSU VIN list only). This bulletin involves reprogramming the PCM with the latest available software.
Source components: BACK OVER PREVENTION · ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · EXTERIOR LIGHTING · FUEL SYSTEM, DIESEL · FUEL SYSTEM, GASOLINE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
UAQ and UCQ Radio Enhancements Customers may experience one or more of the following: ? **Wi-Fi hotspot connection failure. ? Speaker popping, crackle noise during Voice Recognition (VR) response and navigation guidance. ? Mobile Station Integrated Services Digital Network (MSISDN) missing from radio, no connected services working.** ? Intermittent, black radio display screen (Rear View Camera (RVC) not affected). ? Intermittent, radio freezes (RVC not affected). ? Wireless connectivity pairing and/or connection issues. ? Lost radio presets. ? Radio channels change by itself. ? SXMT icon inoperative. ? SXMT favorite song not displaying/playing. ? Incorrect navigation address/location/directions. ? Backup camera has black display screen or only displays Check Entire Surroundings with black screen (occurs when vehicle is shifted immediately to reverse upon key-on before RVC signal is received, recoverable with key cycle) . ? High pitch chime noise. ? Contact list not loading. ? Device not supported message. ? Remote app inoperative. ? Travel-Link fuel price incorrect. ? Backup camera gridlines missing. ? Unable to adjust volume. In addition, the following enhancement are included in this update: ? Enables map updates. ? Heavy Duty (HD) Truck USB HUB improvements. ? HD Truck heated steering wheel improvements This bulletin involves inspecting and if required, updating the radio software level to 40.1. Depending on the radio?s current software level the radio may need a one or two USB update.
Source components: BACK OVER PREVENTION · EQUIPMENT:ELECTRICAL:INFOTAINMENT · STEERING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Digital imaging pre authorization is required for Smart Warranty Base dealers or Pre Approval is required from Regional Office depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Radio Over The Air Software Version Update to 22.66 This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from IR22.64 and IR22.65 to IR22.66. The national launch for the FOTA is expected to begin on January 09, 2023. ? Wi-Fi hotspot connection not working. ? No internet connection message on the phone when trying to connect to a device
NHTSA source summary · Original PDF not reviewed by Recallfolio
Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
Source components: STRUCTURE · STRUCTURE:INTERIOR PANELS:DOOR · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following DTCs have been set: P06E9 - Engine Starter Performance (North America Only). P0456 - EVAP System Small Leak. If DTC P0456 is present use the wiTECH Small Leak Verification test (SLVT) to determine if a leak is present in the system. P141B - Starter Control 1 Circuit Performance. P141C - Starter Control 2 Circuit Performance. P26E4-64 - Starter Control 2 Circuit-Signal Plausibility Failure. P0615-64 - Starter Control Circuit-Signal Plausibility Failure. In addition, the customer may notice one or more of the following conditions:Long engine cranking prior to vehicle start more noticeable when the outside temperature is above 40°c (104°f)(EMEA with Sales Code ED6 only). Vehicle will intermittently not start(South Korea Only). Poor fuel economy. Slight engine pinging noise while accelerating and poor performance. Engine may stall while idling. The engine oil dipstick may indicate a low oil level, however the low oil pressure warning indicator doesnotilluminate in the Instrument Panel Cluster (IPC). No crank condition while pushing the start button numerous times, if they turn the vehicle off completely and then retry it will start normally. Cruise control and adaptive cruise control are inoperable. A ?Service Speed Limiter? message in the IPC and Active Vehicle Speed Limiter (AVSL) will be inoperable. There will be no stored or active DTCs with this IPC message.
Source components: BACK OVER PREVENTION · ELECTRICAL SYSTEM · EXTERIOR LIGHTING · LANE DEPARTURE · PARKING BRAKE · POWER TRAIN · SERVICE BRAKES, HYDRAULIC.