Original record summaries, dates and identifiers for this model-year. Records 101–164 of 164, ordered newest first. Dated records on this page: Dec 8, 2011–Sep 15, 2015.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Sep 15, 2015Service Bulletin/Repair Instructions
ITB13039A
NHTSA communication ID: 10192639
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION This bulletin has compiled Tire Pressure Monitor System (TPMS) and Low Tire Pressure Warning System (LTPWS) information for: - Basic diagnosing of TPMS/LTPWS systems - Radio frequency interference causing a "No Data" (C1708, C1709, C1710, C1711) condition - Sensor leaks - Moving TPMS/LTPWS wheel assemblies from one vehicle to another and TPMS/LTPWS sensor registration - Air pressure changes with altitude and ambient temperatures - Aftermarket tire sealers - Aftermarket wheels - Inflating/deflating tires with TPMS/LTPWS sensors See this bulletin for further detail.
Source components: BACK OVER PREVENTION · LANE DEPARTURE · SERVICE BRAKES · WHEELS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION The information in this bulletin is provided to help ensure correct diagnosis and repair of fluid leaks. All fluid leaks, when properly diagnosed, should be repaired (whether under warranty or customer pay) to ensure proper vehicle operation. However, certain normal operating conditions can be misdiagnosed as a leak requiring repair. Unnecessary repair or replacement of parts in connection with incorrectly diagnosed "leaks" can negatively impact customer satisfaction, be time consuming and costly, and if not performed correctly can lead to future repairs. See this bulletin for further detail.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:FLUID/LUBRICANT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION If the AV Control Unit needs to be replaced on an Applied Vehicle for any reason, follow the steps in the Service Procedure to configure the Multi AV system. NOTE - The original AV Control Unit must be installed in the vehicle while performing part of this procedure. DO NOT remove the original AV Control Unit until instructed. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION The Applied Vehicles are equipped with a new version of Intelligent Key presets memory. Each Intelligent Key can be programmed to have its own unique set of presets for certain vehicle systems. Vehicle systems that are linked with Intelligent Key include: - Automatic Drive Positioner (includes driver seat, steering column, and mirror position memory) - Audio (station presets, etc.) - Auto air conditioning and heating (retains the last temperature and mode setting for each Intelligent Key user) - Navigation system (retains the last settings [e.g., Birdview] and clock display preference for each Intelligent Key user) See this bulletin for further detail.
Source components: AIR BAGS · STEERING · VISIBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION When servicing run flat tires or low profile tires: - Special equipment and procedures are required to avoid damage. - Specifically, Tire Pressure Monitor transmitters (TPMS sensors) can be damaged when improperly dismounting and mounting tires. - TPMS sensors becoming damaged during mounting or dismounting tires are not covered under warranty. - To avoid such damage, ensure that the tire changer being used and the operator of the tire changer are capable of servicing run flat and low profile tires. - Operator?s manuals for such tire changers must be followed. See this bulletin for further detail.
Source components: BACK OVER PREVENTION · EQUIPMENT · SERVICE BRAKES · STEERING · WHEELS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION After ECM reprogramming, the Calibration Verification Number (CVN) needs to be automatically calculated prior to State emissions testing (also known as Inspection Maintainence, I/M, or SMOG testing depending upon location). Allowing the vehicle to idle for 22 minutes will allow for faster CVN calculation. It is recommended that customers utilize this method if the vehicle needs to be tested for emissions soon after ECM reprogramming. See this bulletin for further detail.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION The appearance of painted alloy wheels can be damaged if acidic cleaners are used. DO NOT use Chrome Wheel Cleaner on Painted Wheels. Many chrome wheel cleaners have acidic ingredients. Make sure to follow all instruction in the Appearance and Care Section of the Owner?s Manual. Damage to wheel appearance due to the use of inappropriate chemicals or cleaning products is not covered under warranty. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION For vehicles delivered to the dealers with wheel protector covers - Do not remove the wheel protector covers during Pre-Delivery Inspection (PDI) - Wheel protector covers help prevent cosmetic rotor corrosion. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION NOTE - Failure to follow the procedures in this bulletin may result in the denial of a warranty claim. In an effort to protect the paint finish, Paint Guard Film (PGF) is applied on many new Infiniti vehicles. Paint Guard Film is a temporary white plastic protective film that is applied by the factory to the horizontal painted surfaces of the vehicle. The PGF protects the paint finish during vehicle handling, transportation and storage from harmful elements such as acid rain,iron particles, bird droppings, tree sap and other environmental contaminants. NOTE - Paint Guard Film CANNOT remain on the vehicle for more than six months after the vehicle's manufacture date. PGF must be removed at the end of six months. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION Changes or modifications to the front seat assembly trim materials may affect the proper operation of the Front Seat-Mounted Side-Impact Supplemental Air Bags and Passenger Occupant Classification Sensor and could result in serious personal injury or death. Infiniti STRONGLY RECOMMENDS AGAINST making any change to seat trim materials from the factory equipped condition. This specifically applies to replacing the seat trim with non-factory materials; adding leather/cloth seat covers, seat pads, or seat storage pouches, etc. around or over the seat back and the passenger seat cushion. See this bulletin for further detail.
Source components: AIR BAGS · BACK OVER PREVENTION · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION DTC B2190 (NATS ANTENNA AMP) can be stored for the following reasons: 1. Something other than an Intelligent Key is inserted into the Key-Slot. 2. An Intelligent Key issue. 3. A wiring issue between the Key-Slot and the BCM. 4. A Key-Slot issue. If DTC B2190 is stored due to 1 or 2 above, it will not erase, or go to "PAST", until a known good registered Intelligent Key is inserted into the Key-Slot. For DTC B2190 diagnosis; first perform the Service Manual DTC Confirmation Procedure. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION Two methods are used to update/upgrade Navigation Map Data: 1. The customer goes to www.infinitinavigation.com and is mailed update disc(s) or SD card and installs data, OR 2. The dealership is mailed update disc(s) and the customer must visit the dealership to have data installed. Use the matrix in this bulletin to determine which method is utilized for each Applied Vehicle. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION If a customer would like to activate a subscription for any of the following services: - SiriusXM Satellite Radio, NavTraffic, NavWeather or Travel Link OR If a radio is replaced for any reason, and a customer has an active subscription to any of the above services, OR If a customer claims to have an active subscription to any of the above services, AND any portion of the subscribed service is not operating, ... follow the steps in this bulletin to activate/refresh the service.
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM The Engine Cooling Fan is louder than normal. and There is a noticeable lack of power when accelerating in traffic, particularly in HOT weather. ACTIONS 1. Reprogram the ECM, if necessary. 2. Perform Engine Fan Coupler function inspection. - With engine temperature between 80-95°C (176-203°F), confirm that Cooling Fan speed responds to the commands of the ECM with the procedure starting on page 10. 3. Replace the fan coupler, if necessary. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION Starting with 2010 Model Year, Infiniti vehicles have been gradually incorporating a new type of DTC known as Permanent DTC or P-DTC. If a vehicle is equipped with P-DTCs, all emission related DTCs will also set a P-DTC if the MIL is turned ON. A listing of which DTCs that will also set a P-DTC is found in the DTC Index in the EC-Engine Control section of the Electronic Service Manual (ESM). If a DTC repair is performed and the DTC erased, a vehicle may fail an Emission Inspection and Maintenance test if the P-DTC is not also erased. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION If the auto back door will not operate automatically (operates only in manual mode), first note some conditions that may cause this: * Is DTC B2420 set as "current" in the back door control unit? If the auto back door "CLOSE SW" (close switch) state does not change from ON to OFF after 3 attempts to close the auto back door, B2420 will be set and the auto feature will be disabled. Please see this bulletin for further details.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION If a customer describes lack of power or poor acceleration, perform the following checks before attempting any repair: * Check for stored DTCs. * Check if the driver is resting their left foot on the brake pedal while accelerating. Advise the customer not to rest their foot on the brake while accelerating. * Use CONSULT-III plus in Engine Data Monitor to check operation of the brake lamp circuit signal. Monitor the brake switch during the incident; it should be "OFF". Please see this bulletn for further details.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFRIM An oil leak at the right side block ball plug behind the alternator. ACTION: Use a punch to seat the block ball plug in the hole (refer to the Service Procedure). See this bulletin for further detail.
Source components: ELECTRICAL SYSTEM · ENGINE · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM MIL "ON" with DTC P0420 and/or P0430 (Three Way Catalyst Function), ACTION: 1. Reprogram the ECM (if needed). 2. Replace three way catalyst and A/F sensor. See this bulletin for further detail.
Source components: ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM):SOFTWARE · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION Related to communication codes U1000, U1001, U1002, U1010: - Always diagnose the communication codes first. - When a module reports a U1000 code, it is typically operating normally; however, there is a communication error external to that module on the CAN network. - U1000 indicates an error. V-CAN diagram or CAN Diag Support Monitor provides data to determine the location of the error. See this bulletin for more information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION Warranty claims coding for repairing wiring harnesses for all Infiniti vehicles has changed. This bulletin gives an outline of the retailer technician?s responsibilities in assisting the retailer claims administrator to properly code a harness repair. Failure to provide correct information may result in claims suspension or rejection. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION The rear seat headphones have an "A" channel (Ach) and a "B" channel (Bch). The channel switch is on the headphone ear pad case. If a person is sitting on the left side (driver side) of the vehicle and their headphones are set to Bch, the headphones may have static or intermittently operate (cut in and out). OR If a person is sitting on the right side (passenger side) of the vehicle and their headphones are set to Ach, the headphones may have static or intermittently operate (cut in and out). NOTE: If the headphones are set to the "correct channel" for the seating position, but still have static or do not operate, check the condition of the "AAA" headphone batteries located under the left side headphone cover. Do not replace the headphones for the above issues. See this bulletin for further detail.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION Information necessary to service the Supplemental Restraint System (SRS) safely is included in the "RESTRAINTS" section of the Electronic Service Manual (ESM) for each vehicle IMPORTANT: Turn the ignition switch OFF, disconnect both battery terminals, and wait at least 3 minutes before performing any service on the SRS. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION Replacement Engine Control Modules (ECMs) for many newer Infiniti vehicles are now "Blank" ECMs. Blank ECMs come without software and must be programmed (not reprogrammed) before they will function. See this bulletin for further detail.
Source components: ENGINE · ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION Intelligent Key (I-Key) systems on the Applied Vehicles use two (2) different Radio Frequencies (RF) that are similar to other wireless devices; 315 MHz and 433 MHz. In the event another wireless device (e.g. aftermarket alarm system) is transmitting at the same time as an I-Key, it can interfere with the I-Key signals being received by the BCM. If there is interference with I-Key signals, the following symptoms may occur: - The I-Key is not detected, causing: - The engine to not start (no response when the Stop/Start button is pressed) - "I-Key System Error" displayed in the instrument cluster - "No I-Key Detected" displayed in the instrument cluster - Intermittent operation of the buttons on the remote (Key FOB). - Intermittent operation of the door request switches. If a vehicle has experienced the above symptoms, or a customer has reported the above symptoms, refer to Supplemental Diagnosis / Information in this bulletin. See this bulletin for further detail.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM The customer reports that people on the other end of a phone call cannot hear them. Customer report may include: Voice is choppy or cuts-out, voice sounds distant, voice sounds as if speaking through a tunnel, and/or voice sounds like it's under water. ACTION 1. Reprogram (reconfigure) the Multi AV. 2. Replace the microphone and the map lamp finisher. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM: Both seat heaters of the second row seats do not work. AND Fuse # 14 is found open (or "blown"). NOTE: This issue applies to both captain and bench type second row heated seating. ACTION: 1. Repair the right side second row seat: a. Clean off welding spatter on the seat hinge (the cause of harness damage), and then apply protective covering on the seat hinge. b. Repair the damaged seat harness wiring or replace the seat harness as necessary. - For repairs, refer to SERVICE PROCEDURE starting on page 3. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
INFINITI: WHINE NOISE FROM ENGINE AREA. IF THE NOISE DOES NOT INCREASE WITH ENGINE SPEED, THE TIMING CHAIN SYSTEM MAY NOT BE THE CAUSE. *JS UPDATED 10/29/2013 *JS
NHTSA source summary · Original PDF not reviewed by Recallfolio
Infiniti Original Equipment or Genuine Accessory Alloy wheels, along with their finish coating (clear, chrome, titanium, etc.), are specifically developed to achieve Infiniti design and performance standards. These Original Equipment or Genuine Accessory wheels are subjected to testing to ensure they meet Infiniti's standards. Infiniti Original Equipment Alloy or Genuine Accessory wheels subjected to aftermarket chroming may no longer continue to meet these standards and may be seriously damaged. Therefore, Infiniti most strongly discourages, and recommends that these wheels NEVER be subjected to, aftermarket chroming. See this bulletin for further details.
NHTSA source summary · Original PDF not reviewed by Recallfolio
INFINITI: DUE TO USE OF AFTERMARKET CHROMING OF ALLOY WHEELS, FOR SOME VEHICLES, THE STANDARDS ARE NO LONGER ARE MET AND ARE SERIOUSLY DAMAGED AND NOT GUARANTEE OR WARRANTY THE MODIFIED WHEELS OR PERFORMANCE. MODELS ALL. NO YEARS LISTED. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION This TSB is for troubleshooting of CAN Modules with "Diag-On-CAN" Diagnostics. The flow charts below are meant to troubleshoot current CAN DTCs. The flow charts are intended to diagnose one module at a time; repeat the process as needed for additional control units. Please see this bulletin for further details.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION Part order approval from TECH LINE is no longer required when replacing the Audio Visual (A/V) Control Unit on an Applied Vehicle. Previously, TECH LINE would need to be contacted to confirm (or assist with) diagnosis and the proper repair prior to ordering an A/V control unit. This process has been suspended.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION - This bulletin is to assist you in responding to customer questions about brake operation, and provides diagnostic and repair information for each item listed, if any should occur. - Most brake issues fall into the following categories: a. Brake Noise: A squeak, squeal, clunk, or groan that occurs when the brakes are applied or released. b. Brake Judder: A vibration that can be felt in the vehicle, steering wheel, or brake pedal when the brakes are applied. c. Pedal Feel: The effort needed to operate the brakes is too high or too low. SERVICE PROCEDURE 1. Verify the condition by road testing the vehicle with the customer. 2. Determine the specific brake issue based on the description in the Service Information above. 3. Follow the appropriate repair procedure(s), listed on the following pages, for your specific issue. See this bulletin for further details.
Source components: SERVICE BRAKES · STEERING · SUSPENSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
If YOU CONFIRM: A vehicle needs to have the brake rotors resurfaced (front or rear). ACTION: Use the ProCut PFM Series on-car brake lathe to perform brake rotor resurfacing and follow the tips listed in this bulletin. - The ProCut PFM Series brake lathe has been chosen as the approved tool for rotor resurfacing. - The ProCut PFM Series brake lathe can be ordered from TECH-MATE at 1-800-662-2001. - ProCut technical support or service can be obtained by calling 1-800-543-6618. NOTE: Brake rotors may need to be resurfaced during routine brake repair or for brake "judder" incidents. - Brake judder: A brake pedal pulsation and/or steering wheel shimmy when braking that occurs when there is too much thickness variation of the brake rotors (see ITB00-024). See this bulletin for further detail.
Source components: SERVICE BRAKES · STEERING · WHEELS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
As part of an enhanced emissions test for Inspection & Maintenance (I/M), some States may require the System Readiness Test (SRT) status be checked. - The SRT is used to indicate whether the engine control module (ECM) has completed self diagnosis of major emissions systems and components. - In these instances the State may require completion of the SRT before permitting the emissions inspection to proceed. Refer to this Bulletin for further details.
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM One or more of the following conditions: Front passenger air bag status light is ON (illuminated) with the front passenger seat empty. Front passenger air bag status light is ON (illuminated) with an adult sitting in the front passenger seat. Seat belt warning light is ON (illuminated) with the front passenger seat empty (driver seat belt is buckled). Supplemental air bag warning light is flashing but no Air Bag DTCs are stored. ACTION 1. Visually check the front passenger seat and seat rails for any structural damage. 2. Visually check the front passenger seat for any items in the seat pockets, or any items on, under, or hanging from the seat (front, back, and sides). 3. Replace the OCS control unit. 4. Perform Zero Point Rest and check for DTCs. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION Improper adjustment or operation of the ASCD brake switch can cause the Automatic Speed Control Device (ASCD) to "not set" and/or DTC P0605 (ECM) to store. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
INFINTI: CRUISE CONTROL WILL NOT SET AND DTC P0605 IS STORED. IF A MALFUNCTION IN THE ASCD SYSTEM IS DETECTED, THE CRUISE INDICATOR MAY STAY ON AND THE SET INDICATOR MAY FLASH. *JS
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION The "Lock / Unlock request buttons" that are located on the outside door handles of vehicles with Intelligent Key can be disabled (or enabled) through either the "Comfort & Conv." settings of the Audio/Visual/Navigation system, orthrough the "Combination Meter settings" depending on the vehicle model, year and trim level. NOTE: In some instances this feature may be unintentionally disabled. Please verify the status of this feature before any further diagnostic is performed. Please see this bulletin for further details.
NHTSA source summary · Original PDF not reviewed by Recallfolio
INFINITI: LOCK/UNLOCK REQUEST BUTTON ON OUTSIDE DOOR HANDLE OUTSIDE DOOR HANDLE DOES NOT RESPOND. LOCK/UNLOCK REQUEST BUTTON LOCATED ON OUTSIDE DOOR HANDLES OF VEHICLES CAN BE DISABLED (OR ENABLED) THROUGH EITHER THE "COMFORT & CONV" SETTINGS OF THE AUDIO/VISUAL/NAVIGATION SYSTEM OR THROUGH THE "COMBINATION METER SETTINGS" DEPENDING ON THE VEHICLE MODEL, YEAR, AND TRIM LEVEL. *JS
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM: Customers concern of a "clicking" noise coming from either left or right front/rear axles during take-off/acceleration. ACTION: Apply Molykote M77 grease (P/N 44003-7S000) to the hub bearing surfaces. NOTE: * Do not remove the axle from the hub or transmission for this bulletin * Refer to the Electronic Service Manual (ESM) for model specific torque specifications. >Please see Service procedure for 2007-2011 Versa torque specifications on page 5. See this bulletin for further detail.
Source components: BACK OVER PREVENTION · EQUIPMENT · POWER TRAIN · WHEELS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION This bulletin provides information to identify: - A leaking strut or a shock absorber that qualifies for replacement under warranty. - A strut or shock absorber that has slight oil seepage, a condition which is considered normal, does not affect strut/shock absorber operation or performance, and does not require replacement. - A strut or shock absorber that should be replaced due to rod resistance/noise issues. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM: The following incidents with The Auto Drive Position System: * Door mirrors do not go back to the original preset memory position after the vehicle is shifted into reverse, and then shifted back into drive. * Return position of mirrors drifts farther and farther from original memory preset as mirror is cycled from the drive to reverse positions (cumulative). * With vehicle in park and engine turned off, the Seat and Steering Wheel do not move when exiting vehicle. ACTION: Replace Left Power Seat Control Unit with new part listed in PARTS INFORMATION in this bulletin. See this bulletin for further details.
Source components: POWER TRAIN · STEERING · VEHICLE SPEED CONTROL · VISIBILITY · WHEELS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION When the fluid of an applied vehicle's transfer assembly is being "topped off" or refilled for any reason, use only Genuine NISSAN Transfer Fluid (P/N 999MP-TF0870P). Using transfer fluid other than Genuine NISSAN Transfer Fluid or its equivalent will damage the transfer, which is not covered by the INFINITI new vehicle limited warranty. Order this item through the Infiniti Maintenance Advantage program: Phone: 877-INF-IMA1 (877-463-4621), order online via the link on www.NNAnet.com>Workspace tab>Parts and Service Section>Click on "Maintenance Advantage", or order direct at www.nissantire.com. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION If a CD/DVD Player incident is noted, a possible cause may be improper CD/DVD disc care, condition, or usage. This bulletin provides updated CD/DVD Player operation instructions to avoid potential incidents/customer concerns caused by improper care and usage of CD/DVD discs. To aid in solving customer concerns, use the guidelines in this bulletin when speaking to customers or inspecting incident vehicles. - Customers must not use discs that are warped, scratched, chipped, cracked, have abnormal edges or are otherwise damaged. Damaged or poor condition discs may cause the Player internal mechanism to jam or have optical pick-up errors. NOTE - Do not make a Warranty claim against a Player that will not play damaged or poor condition discs as described in this bulletin. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM One or more of the following is occurring on an Applied Vehicle: - Audio streaming via Bluetooth is "choppy" or "clipped." - Calculating Route" takes an extended period of time (2-5 minutes) to complete. - Could not find a route" displays when attempting to calculate a route. - Voice Recognition sequence takes too many steps. - Voice Recognition has difficulty recognizing voicetags. - The Navigation system reboots. - XM NavTraffic is slow to report. - "Handset Phonebook" access is slow. - Caller ID is not available when a hands-free call via Bluetooth is in progress and another call comes in. ACTION 1. Perform steps 1-7 of Check Navigation Program Version in the Service Procedure to verify whether or not this bulletin applies. 2. If this bulletin applies, Follow the Service Procedure to load the Reprogramming Software DVD referenced in the Parts Information section. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM: Any of the following DTCs are stored in the ECM: - P0031 / P0051, P0032 / P0052, P0130 / P0150, P0133 / P0153, P2A00 / P2A03, P1148 / P1168 OR Any of the following DTCs are stored in the ECM as a result of one of the A/F sensors: - P0300 - P0308, P0171 / P0174, P0172 / P0175 ACTION: 1. Replace the A/F sensor that relates to the stored DTC(s) (B1 and/or B2). 2. Refer to step 7 in the SERVICE PROCEDURE to confirm if ECM reprogramming applies. 3. If it applies, reprogram the ECM. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
IF YOU CONFIRM: An APPLIED VEHICLE has the MIL 'ON' with DTC P008B (Low Fuel Pressure Too High) stored in the ECM. ACTION: 1. Refer to step 6 in the SERVICE PROCEDURE to confirm this bulletin applies to the vehicle you are working on. 2. If this bulletin applies, reprogram the ECM. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION To increase tire/wheel assembly balancing accuracy, proper steps should be followed: - Make sure to use the correct size wheel centering collet (do not use a cone). - Make sure to use a flange plate and stud set to secure the tire/wheel assembly on the balancer (do not use a cup). - Perform proper wheel mounting and centering checks. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Infiniti is conducting a retailer service action to reprogram the ECM on certain specific 2012 and 2013 Infiniti QX56 vehicles to prevent the fuel pump pressure from becoming higher than design specifications and illuminating the MIL light.
Source components: FUEL SYSTEM, GASOLINE · SERVICE BRAKES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION Part of the procedure to remove the glass mirror in either door mirror of an applied vehicle has been changed. Until the related Electronic Service Manuals (ESM) are amended, use the information in this bulletin. - Other than noted, all other procedural steps in the ESM remain the same. See this bulletin for further detail.
Source components: VEHICLE SPEED CONTROL · VISIBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION The "Reverse Tilt-Down" feature will move the glass on the outside mirrors downward when the gear selector is placed in the Reverse (R) position. As the mirror glass moves downward, it may reach the end of its travel. If the mirror glass reaches the end of its travel it will make a clicking noise. The clicking noise may occur once or multiple times. IMPORTANT: - The clicking noise described above is a normal function of the mirror glass movement. - Do not replace the door mirror assembly in an attempt to repair this normal function.
Source components: BACK OVER PREVENTION · ENGINE AND ENGINE COOLING · VEHICLE SPEED CONTROL · VISIBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SERVICE INFORMATION Occasionally, after a rain or a car wash, customers may notice water drops in the overhanging part of the rear combination lamp lens. - This is a normal condition. - The water drops should disappear over time when the lamp is in a dry environment. - Refer to the images on page 2 of this bulletin for examples of a normal water drop condition. - Do not replace any parts for this condition. See this bulletin for further detail.
NHTSA source summary · Original PDF not reviewed by Recallfolio
INFINITI: WHEN INSECTS, DIRT, FINGER PRINTS, OIL FILM, MOISTURE OR EXHAUST GAS IS NEAR OR AROUND RAIN SENSOR, THIS CAUSES THE RAIN SENSOR, WHEN WIPER LEVER IS PUSHED DOWN, TO EITHER MAKE A SINGLE STROKE OR OPERATE UNEXPECTEDLY. NO MODELS OR MODEL YEARS LISTED. *PE