2014 Hyundai SANTA FE SPORT Manufacturer communications & TSBs.Page 2
Original record summaries, dates and identifiers for this model-year. Records 101–133 of 133, ordered newest first. Dated records on this page: Apr 19, 2016–Jul 23, 2019.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Jul 23, 2019Service Bulletin/Repair Instructions
19-BR-001H-1
NHTSA communication ID: 10163866
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin provides information on the rear wheel speed sensor for Santa Fe (CM), Santa Fe / XL (NC), Santa Fe Sport (AN), and Veracruz (EN) vehicles equipped with front wheel drive (FWD). The rear wheel speed sensor is available as a separate service part from the rear wheel hub assembly. When appropriate, it is recommended to replace only the rear wheel speed sensor instead of the full assembly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin provides information on the rear wheel speed sensor for Santa Fe (CM), Santa Fe / XL (NC), Santa Fe Sport (AN), and Veracruz (EN) vehicles equipped with front wheel drive (FWD). The rear wheel speed sensor is available as a separate service part from the rear wheel hub assembly. When appropriate, it is recommended to replace only the rear wheel speed sensor instead of the full assembly.
Source components: SERVICE BRAKES, AIR:ANTILOCK:WHEEL SPEED SENSOR · SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP:WHEEL SPEED SENSOR/TONE RING · WHEELS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This TSB provides a procedure to diagnose and repair a transaxle for the following Incorrect Ratio DTC (transaxle clutch slipping more than 200 rpm in gear).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin provides information for troubleshooting of the Blind-Spot Collision Warning (BCW/BSD) system whenever it exhibits Diagnostic Trouble Code (DTC) C120B/D or C160A.
Source components: FORWARD COLLISION AVOIDANCE · LANE DEPARTURE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Applicable vehicles with 2.0L Turbo and 2.4L GDI engines may experience the Check Engine warning lamp illuminated with DTC P1326. Follow the procedure to inspect the vehicle and install a wire harness extension or replacement engine based on the inspection results.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Hyundai has launched a Service Campaign for applicable vehicles with 2.0L Turbo and 2.4L engines that may experience the Check Engine warning lamp illuminated with DTC P1326.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin provides the procedure to write the Vehicle Identification Number (VIN) during the replacement of the Engine Control Module (ECM) or Powertrain Control Module (PCM). Once the VIN has been programmed to the ECM/PCM, it cannot be removed or overwritten.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin provides information on the serviceable parts for the outside mirror assembly. When diagnosing and repairing the outside mirror, do not replace the entire assembly. Refer to page 2 of this TSB for replacement of individual parts.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Hyundai Motor America is conducting a Service Campaign to update the display audio software on certain 2019 Veloster vehicles. Service Campaign T3Q provides a procedure to update the display audio software for blank home screen.
NHTSA source summary · Original PDF not reviewed by Recallfolio
In a gasoline direct injection (GDI) engine, highly pressurized gasoline is injected via a common rail fuel line and injectors that deliver fuel directly into the combustion chamber of each cylinder. In comparison, in a conventional multi-point fuel injection (MPI) engine, relatively low pressure gasoline is injected into the intake port of each cylinder. Due to high fuel pressures in a GDI system, servicing the GDI system requires special attention and handling procedures. This bulletin provides special service information and specification for the GDI fuel system components.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Applicable vehicles with 2.0L Turbo and 2.4L engines may experience the Check Engine warning lamp illuminated with DTC P1326. Follow the procedure on TSB #19-01-006H (supersedes TSB# 18-01-032-2) to inspect the vehicle and install a wire harness extension or replacement engine based on the inspection results.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The warranty coverage for the engine long block has been extended to 10 years or 120,000 miles from the date of original retail delivery or date of first use, whichever occurs first, and is valid for original and subsequent owners.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Applicable vehicles with 2.0L Turbo and 2.4L GDI engines may experience the Check Engine warning lamp illuminated with DTC P1326. Follow the procedure to inspect the vehicle and install a wire harness extension or replacement engine based on the inspection results.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Hyundai has developed a new engine monitoring technology called a Knock Sensor Detection System (KSDS). The technology uses software innovations and leverages existing engine sensors to continuously monitor for symptoms that may precede an engine failure. Watch this video to learn more. The KSDS software continuously monitors engine vibrations for unusual patterns that develop as an engine connecting rod bearing wears abnormally that could later cause engine seizure. If vibrations caused by bearing wear start to occur, the malfunction indicator lamp will blink continuously, an audible chime will sound and the vehicle will be placed in a temporary engine protection mode with reduced power and acceleration. At that time, Diagnostic Trouble Code (DTC) P132600 will be recorded in the ECM. In addition, Hyundai will extend the warranty to 10 years and 120,000 miles (up from 100,000 miles) for original and subsequent owners of the covered vehicles for engine repairs needed because of excessive connecting rod bearing damage.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Hyundai is conducting a product improvement campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, a chime will sound on certain vehicles, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Engine Protection Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The software update installs a newly developed Knock Sensor Detection System (KSDS) that detects vibrations indicating the onset of excessive connecting rod bearing wear in the engine. The KSDS is designed to alert a vehicle driver at an early stage of bearing wear before the occurrence of engine damage. If vibrations caused by bearing wear start to occur, the Malfunction Indicator Lamp (MIL) will blink continuously, an audible chime will sound, and the vehicle will be placed in Limp Home Mode. At that time, Diagnostic Trouble Code (DTC) P132600, specific to the KSDS, will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Limp Home Mode, but it will accelerate slowly and have a reduced maximum speed with RPMs limited to approximately 1800-2000 RPM. The update will be done free of charge to customers and will only involve the addition of the KSDS software update.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Hyundai is conducting a product improvement campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, a chime will sound on certain vehicles, and the vehicle will be placed in Limp Home Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Limp Home Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Hyundai is conducting a product improvement campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, a chime will sound on certain vehicles, and the vehicle will be placed in Limp Home Mode allowing the customer to drive to the nearest Hyundai dealer for diagnosis and repair. In addition, DTC P132600 will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Limp Home Mode, but it will accelerate slower and have a reduced maximum speed. Engine RPMs will be limited to approximately 1800-2000 RPM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Hyundai has launched a Product Improvement Campaign to perform a knock sensor software update on the subject vehicles. This campaign is being implemented to ensure the satisfaction of Hyundai customers. The software update installs a newly developed Knock Sensor Detection System (KSDS) that detects vibrations indicating the onset of excessive connecting rod bearing wear in the engine. The KSDS is designed to alert a vehicle driver at an early stage of bearing wear before the occurrence of engine damage. If vibrations caused by bearing wear start to occur, the Malfunction Indicator Lamp (MIL) will blink continuously, an audible chime will sound, and the vehicle will be placed in Limp Home Mode. At that time, Diagnostic Trouble Code (DTC) P132600, specific to the KSDS, will be recorded in the ECM. The vehicle can continue to be operated for a limited time in Limp Home Mode, but it will accelerate slowly and have a reduced maximum speed with RPMs limited to approximately 1800-2000 RPM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The shift lever on some 6-speed vehicles may intermittently not shift out of Park. This bulletin provides the diagnostic procedures to correct this condition.
Source components: EQUIPMENT · POWER TRAIN · POWER TRAIN:MANUAL TRANSMISSION:INTERNAL:GEARS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When towing a trailer with some LF/LF-HEV/LF-PHEV Sonatas or some AN/NC Santa Fe vehicles equipped with the Blind Spot Detection (BSD) feature, the trailer may interfere with the BSD system operation resulting in cancellation of the BSD operation. When this occurs, a ?BSD canceled? message is displayed in the vehicle?s instrument cluster. The ?BSD canceled? message remains on even if the customer manually disables the BSD system, and may result in customer complaints. This bulletin provides the service procedure to update the system software to turn off the ?BSD canceled? message when the BSD system is manually disabled.
Source components: BACK OVER PREVENTION: CAMERA SYSTEM · ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL · ELECTRICAL SYSTEM:SOFTWARE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Before installing an automatic transmission, check the depth of the torque converter in the case to confirm the torque converter is fully installed in the transmission. If this is not done, the oil pump may be damaged.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
If you are servicing a vehicle with the DTC or symptoms listed below, refer to the Service Procedure to diagnose the condition. ? Diagnostic trouble codes: ? P0705 - Range switch sensor circuit ? P0706 - Range switch range/performance ? P0707 - Range switch - open circuit ? P0708 - Range switch - short circuit or multiple inputs ? Symptoms: ? Malfunction Indicator Light (MIL) illuminated ? 4th gear fail-safe ? No gear indication in cluster ? Intermittent no engine crank/no start in ?P? or ?N? with or without MIL or DTC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When towing a trailer with some LF/LF-HEV/LF-PHEV Sonatas or some AN/NC Santa Fe vehicles equipped with the Blind Spot Detection (BSD) feature, the trailer may interfere with the BSD system operation resulting in cancellation of the BSD operation. When this occurs, a ?BSD canceled? message is displayed in the vehicle?s instrument cluster. The ?BSD canceled? message remains on even if the customer manually disables the BSD system, and may result in customer complaints. This bulletin provides the service procedure to update the system software to turn off the ?BSD canceled? message when the BSD system is manually disabled.
NHTSA source summary · Original PDF not reviewed by Recallfolio
If the rear wheel hub in the affected vehicles is submerged in salt water, salt water can enter the rear wheel speed sensor housing and may interrupt the rear wheel speed sensor signal and temporarily illuminate the ABS and/or ESC warning lights in the instrument cluster until the sensor dries. For these cases, replacement of the wheel speed sensor cap is required. If no ABS/ESC warning lamp is illuminated, applying a silicone spray to the sensor is required. This bulletin describes the service procedure for the rear wheel speed sensors.
Source components: SERVICE BRAKES, AIR:ANTILOCK:WHEEL SPEED SENSOR · SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP:WHEEL SPEED SENSOR/TONE RING · WHEELS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
If the rear wheel hub in the affected vehicles is submerged in salt water, salt water can enter the rear wheel speed sensor housing and may interrupt the rear wheel speed sensor signal and temporarily illuminate the ABS and/or ESC warning lights in the instrument cluster until the sensor dries. For these cases, replacement of the wheel speed sensor cap is required. If no ABS/ESC warning lamp is illuminated, applying a silicone spray to the sensor is required. This bulletin describes the service procedure for the rear wheel speed sensors.
Source components: SERVICE BRAKES, AIR:ANTILOCK:WHEEL SPEED SENSOR · SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP:WHEEL SPEED SENSOR/TONE RING · WHEELS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME SONATA 2.0T (YF) AND SANTA FE SPORT 2.0T (AN) VEHICLES MAY EXPERIENCE A SLIGHT LEAK FROM THE OIL FEED HOSE ASSEMBLY ONTO THE ENGINE UNDERCOVER DIRECTLY BENEATH THE HOSE.
Source components: ENGINE AND ENGINE COOLING:COOLING SYSTEM:HOSES/LINES/PIPING/FITTINGS · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM.