Original record summaries, dates and identifiers for this model-year. Records 1,401–1,500 of 1,564, ordered newest first. Dated records on this page: Jun 1, 2013–Jan 21, 2014.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Jan 21, 2014Service Bulletin/Repair Instructions
PIT5195A
NHTSA communication ID: 10112009
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the speedometer needle appears to be inaccurate. Dealer should advise the customer the specification for speedometer needle accuracy is +/- 2 MPH at any given speed when looking straight at the needle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that a driveline noise or vibration at various speeds and operating conditions. Technician should be advised that the vehicle should always be restored to a factory configuration when diagnosing noise and vibration concerns.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code C0569 that will not clear. Technician should be advised if there are any issues with the rotational position sensor, incremental position sensor, encoder motor, motor A or B circuits, rotational position sensor or incremental position sensor circuits when the transfer case control module attempts to determine location the location cannot be determined correctly.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Service Suspension System message on the Driver Information Center and the rear suspension ride height is incorrect. Technician will find Diagnostic Trouble Code C0696 or C0711 set in Electronic Suspension Control. Technician will need to inspect air compressor assembly for wire damage and repair any damage do not replace the complete air compressor assembly. Some vehicles may have a Service Suspension System message on the Driver Information Center and may also comment that the rear suspension ride height may be low under a heavy payload. Technician will follow published Service Information diagnostics and if determine if the sensor needs to be replaced technician will need to replace a complete air filter, dryer, and sensor assembly. Some vehicles may have a loose hose hanging down in the left rear of the vehicle. Technician will replace the auto leveling compressor air inlet filter and hose assembly. Also some vehicles may have automatic level control compressor is no longer performing a self-test at start up. Be advised the automatic level system normally will not or very infrequently cycle the compressor at key up.
Source components: SERVICE BRAKES, AIR:SUPPLY:COMPRESSOR · SUSPENSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION · POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that a noise or a vibration in the vehicle that seems to be abnormal may not have been there when the vehicle was purchased. Technician should look for Non - General Motors aftermarket accessories installed on the vehicle that can cause these issues.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Informational bulletin explains the warranty and policy exchange program for electronic devices and products, what can be approved by TAC and where the electronic parts can be returned to.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT:ELECTRICAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This information was created to inform the technician that the 2-3 upshift and the 3-2 downshift clunk is caused by the releasing of the 2-4 band and application of the 3-4 clutch assembly during an upshift. Also during a 3-2 downshift, the releasing of the 3-4 clutch during the application of the 2-4 band, can cause torque reversal down the output shaft creating a clunk. This is a normal condition.
Source components: POWER TRAIN · POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER · POWER TRAIN:CLUTCH ASSEMBLY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that some vehicles may have a Service Engine Soon lamp, engine misfire on cylinder 1, 4, 6, or 7 and/or tick noise. Technician will follow service information diagnosis first. If service information diagnosis does not isolate the cause of this concern perform a cylinder deactivation active fuel management system compression test in service information. If the running compression of the misfiring cylinder stays below 25 Pounds per Square Inch regardless of the active fuel management solenoid being commanded on or off, an active fuel management lifter is mechanically collapsed/stuck or unlocking as soon as the engine is started. Replace all active fuel management lifters, and all plastic lifter guides. Also perform the cylinder deactivation active fuel management Valve Lifter Oil Manifold Diagnosis and Testing in Service Information. If it isolates a concern with the Valve Lifter Oil Manifold, replace it and reevaluate the concern. The active fuel management lifters can also be monitored for proper operation by carefully inspecting the cylinder 1, 4, 6, and 7 rockers and valves while cranking or briefly and safely running the engine with the valve covers removed. If the valve or valves of an active fuel management cylinder stop moving while doing this test, the active fuel management lifter is causing the concern. For 2008-2009 Full Size Truck/SUV or a 2007-2009 Chevrolet Tahoe with the Police Package reprogram the Engine Control Module. On the 2008-2009 Pontiac G8, 2010-2011 Camaro, and 2007-2010 Full Size Trucks with active fuel management, also determine if the active fuel management pressure relief valve shield that is listed in the latest version of 10-06-01-008 has ever been installed. On passenger cars with the LS4 engine, determine if the updated oil pan gasket that is listed in the latest version of 11-06-01-007 has been installed.
Source components: ENGINE AND ENGINE COOLING · ENGINE AND ENGINE COOLING:ENGINE:OTHER FUEL TYPES:TURBO/SUPERCHARGER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provide policy information of the JOB CARD, for a repair on vehicles and what is acceptable - customer authorization; Service manager approvals and transaction authorization; Details of concern, cause and correction; Labor Time; Technician ID and acoutablity of labor time; Proper documentation and retension of warranty parts; Accurate sublet charges and receipts; Add on concerns after the Job Card has been written.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an aftermarket, add-on back up alarm will sound when unlocking the doors with the Remote Keyless Entry remote. Technician can correct this concern by turning off the perimeter lighting feature on vehicles with Driver Information Center controls or install an isolation relay in-line to the backup alarm.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provide policy information of the JOB CARD, for a repair on vehicles and what is acceptable - customer authorization; Service manager approvals and transaction authorization; Details of concern, cause and correction; Labor Time; Technician ID and acoutablity of labor time; Proper documentation and retension of warranty parts; Accurate sublet charges and receipts; Add on concerns after the Job Card has been written.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.
Source components: EQUIPMENT ADAPTIVE/MOBILITY · STRUCTURE:FRAME AND MEMBERS:UNDERBODY SHIELDS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.
Source components: EQUIPMENT ADAPTIVE/MOBILITY · STRUCTURE:FRAME AND MEMBERS:UNDERBODY SHIELDS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that after turning the ignition off and opening the driver's door that they can turn the radio on. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an instrument panel backlighting flashes, flickers or inoperative, unwanted horn activation, radio controls inoperative or unwanted activation, OnStar unwanted activation, and cruise control inoperative. Technician should inspect for a short to ground on the steering wheel near the Supplemental Inflatable Restraint coil connector X2 and make necessary repairs to any shorted circuits and then position the wiring.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:WIRING · STEERING: STEERING WHEEL/HANDLE BAR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician with the steps on diagnosing and repairing vehicles that may have unwanted grade braking, reduced engine power with no Driver Information Center messages " Brake Pedal Override Feature ", transmission busy or frequent shifting up or down. Technician will use this preliminary information to find the brake pedal position data parameters in the scan tool, and also to provide some additional diagnostic help. These issues may be caused by an incorrect brake pedal position sensor input to the engine control module. Technician will verify with the scan tool if the engine control module has the correct parameters for the brake pedal position sensor.
Source components: ELECTRICAL SYSTEM:SOFTWARE · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM) · SERVICE BRAKES, AIR:CONTROLS:FOOT CONTROL/VALVE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that are equipped with 6L80 Regular Production Option Code (MYC), 6L90 Regular Production Option Code (MYD) or 8L90 Regular Production Option Code (M5U) Automatic Transmission. Starting with the 2013 model year, Full Size Trucks and Utilities now have Powertrain Grade Braking. Powertrain grade braking assists when driving on a downhill grade to help maintain desired vehicle speed by using the engine and transmission to slow the vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on. Technician may find DTCs P057C and or P057D. Some vehicles may have cruise and brake light operation service stability message with Diagnostic Trouble Codes C0161 and C0277. Technician will need to inspect connector X205 for loose, backed out, or bent terminals using the appropriate terminal test probe.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician about key and theft information for Fleet Vehicles equipped with RPO 6E2 or 6E8 and converting to fleet mode. Technician will need to ensure fleet vehicles with RPO 6E2 or 6E8 should be checked to verify that the Theft Deterrent Module is in fleet mode prior to attempting to add keys.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:ANTI-THEFT DEVICES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary Informational bulletin provides information on Battery Test Cold Cranking Amperage (CCA) for Original Equipment Batteries and Testing Tips.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the Human Machine Interface, Radio or Tuner, radio controls, Integrated Center Stack, display, and Media Disc Players are placed on restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about customers that may complain of various concerns when using Bluetooth components. Technician should use the Preliminary Information to gather information from the customer on their Bluetooth device and the concern they are having before calling General Motors Technical Assistance Center.
NHTSA source summary · Original PDF not reviewed by Recallfolio
GENERAL MOTORS: THE WINDOWS, FRONT AND REAR, WOULD BIND, POOR FIT, MISALIGNMENT, MAKES RATTLE OR SQUEAKING NOISES, MOVES SLOWLY AND IS INOPERATIVE. MODEL 2008-2014 VEHICLES AND TRUCKS. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that some vehicles may have a Service Engine Soon lamp, engine misfire on cylinder 1, 4, 6, or 7 and/or tick noise. Technician will follow service information diagnosis first. If service information diagnosis does not isolate the cause of this concern perform a cylinder deactivation active fuel management system compression test in service information. If the running compression of the misfiring cylinder stays below 25 Pounds per Square Inch regardless of the active fuel management solenoid being commanded on or off, an active fuel management lifter is mechanically collapsed/stuck or unlocking as soon as the engine is started. Replace all active fuel management lifters, and all plastic lifter guides. Also perform the cylinder deactivation active fuel management Valve Lifter Oil Manifold Diagnosis and Testing in Service Information. If it isolates a concern with the Valve Lifter Oil Manifold, replace it and reevaluate the concern. The active fuel management lifters can also be monitored for proper operation by carefully inspecting the cylinder 1, 4, 6, and 7 rockers and valves while cranking or briefly and safely running the engine with the valve covers removed. If the valve or valves of an active fuel management cylinder stop moving while doing this test, the active fuel management lifter is causing the concern. For 2008-2009 Full Size Truck/SUV or a 2007-2009 Chevrolet Tahoe with the Police Package reprogram the Engine Control Module. On the 2008-2009 Pontiac G8, 2010-2011 Camaro, and 2007-2010 Full Size Trucks with active fuel management, also determine if the active fuel management pressure relief valve shield that is listed in the latest version of 10-06-01-008 has ever been installed. On passenger cars with the LS4 engine, determine if the updated oil pan gasket that is listed in the latest version of 11-06-01-007 has been installed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
13364 - Service Update. Replace the passenger side front air bag. These vehicles may have a condition in which the passenger side front air bag will not function as designed due to an electrical connector not being properly engaged. This condition may set diagnostic trouble code (DTC) B0020 ? Passenger Frontal Deployment Loop Stage 2 Resistance Above Threshold. If this occurs, the Sensing and Diagnostic Module (SDM) will request the instrument cluster to illuminate the air bag malfunction indicator lamp. If a crash event occurs the SDM will attempt air bag deployment, but, if the mating terminals do not make contact, the secondary stage of the passenger side front air bag will not deploy, increasing the risk of injury to the occupant.
Source components: AIR BAGS · ELECTRICAL SYSTEM:SOFTWARE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about customers that are unable to override the automatic door locking feature. Technician will update the Body Control Module on 2006 to 2007 model years. On 2010 to 2014 model years technician will need to contact Techline Customer Support for calibrations.
Source components: ELECTRICAL SYSTEM · LATCHES/LOCKS/LINKAGES:DOORS:LATCH · STRUCTURE:BODY:DOOR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about customer's wanting to add the factory Integrated Trailer Brake Controller Regular Production Option Code (JL1) be installed on their Full Size pickup/utility when the vehicle was not ordered with the option. Dealer should advise the customer that if the vehicle does not have the option Regular Production Option Code (JL1) it cannot be added to the vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have power lift-gate that is inoperative from all the switches and the keyless entry transmitter only with the ignition in the off position. Technician will need to inspect circuit 5985 for battery voltage. Repair any damaged wires or terminals.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL · STRUCTURE:BODY:HATCHBACK/LIFTGATE · STRUCTURE:BODY:HATCHBACK/LIFTGATE:HINGE AND ATTACHMENTS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have multiple electrical concerns and or intermittent no crank. Technician will need to remove the 175 amp Mega Fuse and inspect for arcing. If any type of arcing is found replace the affected components. Technician will also check the voltage drop on the positive and negative and the torque of the cable at the starter.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have Service Engine Soon Malfunction Indicator Lamp on and a constant engine misfire. If Service Information diagnosis isolates no compression on the misfiring cylinder(s) with 100% leakage into the crankcase, perform the following steps as necessary before disassembling the engine. Technician will use a lighted bore scope if available to inspect the top of the related piston(s) through the spark plug hole to determine if any of the pistons are melted. If damaged piston(s) are found inspect for aftermarket parts. Also use the latest version of 09-06-04-026 to verify if there are aftermarket calibrations in the Engine Control Module. Take photos and document accordingly if anything is found.
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down, remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics. Technician may need to contact General Motors Technical Assistance Center depending on the STID, Station ID, or OnStar Customer Identifier.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D-37 history in the Vehicle Communication Interface Module or telematics communication interface control module. Engineering has determined that this code will only display in history on the scan tool and will not cause issues with OnStar system operation.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will need to call General Motors Technical Assistance Center for further assistance. If the Diagnostic Trouble Code B101D has a sym 37 set please refer to the latest version of PIC5492.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about the percentage of UV protection or tint offered by the windshield or side glass. Technician should be advised Windshield reduces UV rays down to 4% or less. Front side door glass reduces UV rays down to 35% or less. Windshields are SOLAR glass with a light transmittance of >/=70%. Front door glass are Solar glass with a light transmission of >/=70%. Rear door glass, quarter windows and back windows can use either Solar glass (>/=70%) or Privacy glass, which has a light transmittance of 20%.
NHTSA source summary · Original PDF not reviewed by Recallfolio
GM: INFORMATION CONCERNING THE CONTROL MODULE PART SERVICE NAME OF SOME 2014 MODEL YEAR VEHICLES. THE COMPONENT PART SERVICE NAME CHASSIS CONTROL MODULE IN PUBLICATIONS AND SERVICE TOOLS. MAKE/MODELS INCLUDE BUICK/ENCLAVE, CADILLAC/CTS COUPE/WAGON/ CTS-V/ ESCALADE, CHEVROLET/EXPRESS/IMPALA LIMITED/SILVERADO 2500-3500 HD/ SUBURBAN/TAHOE/TRAVERSE, AND GMC/ACADIA/SAVANA/SIERRA 2500-3500 HD/ YUKON/YUKON XL. *JS
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down, remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics. Technician may need to contact General Motors Technical Assistance Center depending on the STID, Station ID, or OnStar Customer Identifier.
Source components: ELECTRICAL SYSTEM · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the Human Machine Interface, Radio or Tuner, radio controls, Integrated Center Stack, display, and Media Disc Players are placed on restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partech for assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
BUICK/CADILLAC/CHEVROLET/GMC/PONTIAC/ SATURN: THERE IS FLUID LEAKING FROM POWER STEERING SYSTEM, ALONG A FLUID LEAK IN FRONT OF VEHICLE UNDERNEATH AND SHOULD BE INSPECTED, CLEANED AND IDENTIFIED BEFORE REPAIRING OR REPLACING. MODEL 2010-14 LACROSSE, 2011-14 REGAL, 2007-14 ESCALADE, SUBURBAN, TAHOE, YUKON, YUKON XL, YUKON DENALI, YUKON DENALI XL, 2013-14 XTS, 2005-14 MALIBU, 2007-13 AVALANCHE, SILVERADO, SIERRA, 2006-10 G6, 2007-09 AURA. *PE
Source components: STEERING:HYDRAULIC POWER ASSIST SYSTEM · STEERING:HYDRAULIC POWER ASSIST:POWER STEERING FLUID.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on Part Restriction and Ordering Process Information for OnStar Vehicle Communication Interface Modules (VCIM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provide policy information on GM of Canada New Vehicle Limited Warranty Tire Program and Global Warranty Management (GWM) Submission Information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provide policy information on a revised customer concern not duplicated/verified labor operation numbers and how to submit CCND.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM · EQUIPMENT ADAPTIVE/MOBILITY · EQUIPMENT:APPLIANCE:AIR CONDITIONER · EQUIPMENT:ELECTRICAL · POWER TRAIN:AXLE ASSEMBLY · SERVICE BRAKES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the OnStar system will not connect. Technician should record module info per the latest version of PIC4310 and contact General Motors Technical Assistance Center.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that one or both of the roof mounted video screens will not turn on. Technician will need to inspect X206 and X306 for terminal damage or loose connections.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary information bulletin provides information on poor or no transmitter range when using the remote keyless entry (RKE) and/or remote vehicle start (RVS).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about an owner that may request to have a different style mirror installed on their vehicle or request a different mirror before they purchase the vehicle. Swapping mirrors on vehicles equipped with Side Blind Zone Alert, Regular Production Option Code UFT, is not recommended. On other vehicles tech will need to verify if the vehicle is equipped with door modules or not. On vehicles with door modules technician will need to contact Techline Customer Support for new calibrations for both doors. On vehicles not equipped with door modules no calibrations are needed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a revision for 12-02-32-002 to add the 2013-2014 model years, add noise as a possible condition and add a Note in the Instructions section.
Source components: STEERING · STEERING:HYDRAULIC POWER ASSIST:POWER STEERING FLUID.