Original record summaries, dates and identifiers for this model-year. Records 1,101–1,200 of 1,450, ordered newest first. Dated records on this page: May 30, 2013–Jan 16, 2014.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Jan 16, 2014Service Bulletin/Repair Instructions
PIP3140F
NHTSA communication ID: 10111997
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that a noise or a vibration in the vehicle that seems to be abnormal may not have been there when the vehicle was purchased. Technician should look for Non - General Motors aftermarket accessories installed on the vehicle that can cause these issues.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Informational bulletin explains the warranty and policy exchange program for electronic devices and products, what can be approved by TAC and where the electronic parts can be returned to.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT:ELECTRICAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This information was created to inform the technician that the 2-3 upshift and the 3-2 downshift clunk is caused by the releasing of the 2-4 band and application of the 3-4 clutch assembly during an upshift. Also during a 3-2 downshift, the releasing of the 3-4 clutch during the application of the 2-4 band, can cause torque reversal down the output shaft creating a clunk. This is a normal condition.
Source components: POWER TRAIN · POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER · POWER TRAIN:CLUTCH ASSEMBLY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that some vehicles may have a Service Engine Soon lamp, engine misfire on cylinder 1, 4, 6, or 7 and/or tick noise. Technician will follow service information diagnosis first. If service information diagnosis does not isolate the cause of this concern perform a cylinder deactivation active fuel management system compression test in service information. If the running compression of the misfiring cylinder stays below 25 Pounds per Square Inch regardless of the active fuel management solenoid being commanded on or off, an active fuel management lifter is mechanically collapsed/stuck or unlocking as soon as the engine is started. Replace all active fuel management lifters, and all plastic lifter guides. Also perform the cylinder deactivation active fuel management Valve Lifter Oil Manifold Diagnosis and Testing in Service Information. If it isolates a concern with the Valve Lifter Oil Manifold, replace it and reevaluate the concern. The active fuel management lifters can also be monitored for proper operation by carefully inspecting the cylinder 1, 4, 6, and 7 rockers and valves while cranking or briefly and safely running the engine with the valve covers removed. If the valve or valves of an active fuel management cylinder stop moving while doing this test, the active fuel management lifter is causing the concern. For 2008-2009 Full Size Truck/SUV or a 2007-2009 Chevrolet Tahoe with the Police Package reprogram the Engine Control Module. On the 2008-2009 Pontiac G8, 2010-2011 Camaro, and 2007-2010 Full Size Trucks with active fuel management, also determine if the active fuel management pressure relief valve shield that is listed in the latest version of 10-06-01-008 has ever been installed. On passenger cars with the LS4 engine, determine if the updated oil pan gasket that is listed in the latest version of 11-06-01-007 has been installed.
Source components: ENGINE AND ENGINE COOLING · ENGINE AND ENGINE COOLING:ENGINE:OTHER FUEL TYPES:TURBO/SUPERCHARGER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provide policy information of the JOB CARD, for a repair on vehicles and what is acceptable - customer authorization; Service manager approvals and transaction authorization; Details of concern, cause and correction; Labor Time; Technician ID and acoutablity of labor time; Proper documentation and retension of warranty parts; Accurate sublet charges and receipts; Add on concerns after the Job Card has been written.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an aftermarket, add-on back up alarm will sound when unlocking the doors with the Remote Keyless Entry remote. Technician can correct this concern by turning off the perimeter lighting feature on vehicles with Driver Information Center controls or install an isolation relay in-line to the backup alarm.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that are setting Diagnostic Trouble Code P0300 after engine repairs. Technician will need to ensure that injector connectors for cylinder 5-7 and 6-8 are not crossed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a no crank concern. Technician will need to check the valve train for movement when the engine is cranked. If the valve train is not moving while the crankshaft is moving the front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the valve train is rotating during inspection, disconnect the Camshaft Position sensor and check if the engine will start. If the engine starts front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the engine does not start with the Camshaft Position sensor disconnected the follow published ?Engine Cranks But Does Not Run? diagnosis in Service Information. Also perform an Engine Compression Test and Cylinder Leakage Test in Service Information documents all results. If the Service Information procedures above isolate an engine mechanical concern then removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provide policy information of the JOB CARD, for a repair on vehicles and what is acceptable - customer authorization; Service manager approvals and transaction authorization; Details of concern, cause and correction; Labor Time; Technician ID and acoutablity of labor time; Proper documentation and retension of warranty parts; Accurate sublet charges and receipts; Add on concerns after the Job Card has been written.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.
Source components: EQUIPMENT ADAPTIVE/MOBILITY · STRUCTURE:FRAME AND MEMBERS:UNDERBODY SHIELDS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.
Source components: EQUIPMENT ADAPTIVE/MOBILITY · STRUCTURE:FRAME AND MEMBERS:UNDERBODY SHIELDS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin is a revision of 10-06-01-008I to add the 2010-2012 Chevrolet Colorado and GMC Canyon, RPO LH9 and update the Labor Operation to the Global Labor Code (GLC).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an instrument panel backlighting flashes, flickers or inoperative, unwanted horn activation, radio controls inoperative or unwanted activation, OnStar unwanted activation, and cruise control inoperative. Technician should inspect for a short to ground on the steering wheel near the Supplemental Inflatable Restraint coil connector X2 and make necessary repairs to any shorted circuits and then position the wiring.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:WIRING · STEERING: STEERING WHEEL/HANDLE BAR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician about key and theft information for Fleet Vehicles equipped with RPO 6E2 or 6E8 and converting to fleet mode. Technician will need to ensure fleet vehicles with RPO 6E2 or 6E8 should be checked to verify that the Theft Deterrent Module is in fleet mode prior to attempting to add keys.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:ANTI-THEFT DEVICES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about customers that may complain of various concerns when using Bluetooth components. Technician should use the Preliminary Information to gather information from the customer on their Bluetooth device and the concern they are having before calling General Motors Technical Assistance Center.
NHTSA source summary · Original PDF not reviewed by Recallfolio
GENERAL MOTORS: THE WINDOWS, FRONT AND REAR, WOULD BIND, POOR FIT, MISALIGNMENT, MAKES RATTLE OR SQUEAKING NOISES, MOVES SLOWLY AND IS INOPERATIVE. MODEL 2008-2014 VEHICLES AND TRUCKS. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a random bump, chuggle, or fishbite sensation when crowding the throttle slightly with the Torque Converter Clutch on while cruising at 35-60 miles per hour. Technician should follow all published Service Information diagnostics if the concern is repaired compare to a like vehicle with the same options.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that some vehicles may have a Service Engine Soon lamp, engine misfire on cylinder 1, 4, 6, or 7 and/or tick noise. Technician will follow service information diagnosis first. If service information diagnosis does not isolate the cause of this concern perform a cylinder deactivation active fuel management system compression test in service information. If the running compression of the misfiring cylinder stays below 25 Pounds per Square Inch regardless of the active fuel management solenoid being commanded on or off, an active fuel management lifter is mechanically collapsed/stuck or unlocking as soon as the engine is started. Replace all active fuel management lifters, and all plastic lifter guides. Also perform the cylinder deactivation active fuel management Valve Lifter Oil Manifold Diagnosis and Testing in Service Information. If it isolates a concern with the Valve Lifter Oil Manifold, replace it and reevaluate the concern. The active fuel management lifters can also be monitored for proper operation by carefully inspecting the cylinder 1, 4, 6, and 7 rockers and valves while cranking or briefly and safely running the engine with the valve covers removed. If the valve or valves of an active fuel management cylinder stop moving while doing this test, the active fuel management lifter is causing the concern. For 2008-2009 Full Size Truck/SUV or a 2007-2009 Chevrolet Tahoe with the Police Package reprogram the Engine Control Module. On the 2008-2009 Pontiac G8, 2010-2011 Camaro, and 2007-2010 Full Size Trucks with active fuel management, also determine if the active fuel management pressure relief valve shield that is listed in the latest version of 10-06-01-008 has ever been installed. On passenger cars with the LS4 engine, determine if the updated oil pan gasket that is listed in the latest version of 11-06-01-007 has been installed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about customers that are unable to override the automatic door locking feature. Technician will update the Body Control Module on 2006 to 2007 model years. On 2010 to 2014 model years technician will need to contact Techline Customer Support for calibrations.
Source components: ELECTRICAL SYSTEM · LATCHES/LOCKS/LINKAGES:DOORS:LATCH · STRUCTURE:BODY:DOOR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about customer's wanting to add the factory Integrated Trailer Brake Controller Regular Production Option Code (JL1) be installed on their Full Size pickup/utility when the vehicle was not ordered with the option. Dealer should advise the customer that if the vehicle does not have the option Regular Production Option Code (JL1) it cannot be added to the vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have power lift-gate that is inoperative from all the switches and the keyless entry transmitter only with the ignition in the off position. Technician will need to inspect circuit 5985 for battery voltage. Repair any damaged wires or terminals.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL · STRUCTURE:BODY:HATCHBACK/LIFTGATE · STRUCTURE:BODY:HATCHBACK/LIFTGATE:HINGE AND ATTACHMENTS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have multiple electrical concerns and or intermittent no crank. Technician will need to remove the 175 amp Mega Fuse and inspect for arcing. If any type of arcing is found replace the affected components. Technician will also check the voltage drop on the positive and negative and the torque of the cable at the starter.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have various 2-Mode Hybrid issues. Some vehicle may have service hybrid system lamp that comes on with a Diagnostic Trouble Code P061B set. Technician will need to take a snap shot of the Electronic Brake Control Module and call General Motors Technical Assistance Center for further assistance. Some vehicles may have a combination of engine stall at a stop, lacks power on acceleration, surge while driving, engine flare, transmission slip, poor or lower fuel economy or reduced EV range/limited electric propulsion since completion of recent programming. Technician will need to perform a Charge Procedure. Some vehicles have Diagnostic Trouble Code P0BBD stored without Diagnostic Trouble Code P061B or P0AFA. Technician will verify that the Drive Motor Battery was not run low on charge due to a no start concern.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:PROPULSION SYSTEM:TRACTION BATTERY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have Service Engine Soon Malfunction Indicator Lamp on and a constant engine misfire. If Service Information diagnosis isolates no compression on the misfiring cylinder(s) with 100% leakage into the crankcase, perform the following steps as necessary before disassembling the engine. Technician will use a lighted bore scope if available to inspect the top of the related piston(s) through the spark plug hole to determine if any of the pistons are melted. If damaged piston(s) are found inspect for aftermarket parts. Also use the latest version of 09-06-04-026 to verify if there are aftermarket calibrations in the Engine Control Module. Take photos and document accordingly if anything is found.
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down, remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics. Technician may need to contact General Motors Technical Assistance Center depending on the STID, Station ID, or OnStar Customer Identifier.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D-37 history in the Vehicle Communication Interface Module or telematics communication interface control module. Engineering has determined that this code will only display in history on the scan tool and will not cause issues with OnStar system operation.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will need to call General Motors Technical Assistance Center for further assistance. If the Diagnostic Trouble Code B101D has a sym 37 set please refer to the latest version of PIC5492.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Unnecessary Flushing Services, Additive Recommendations and Proper Utilization of GM Goodwrench Maintenance Schedule to Enhance Customer Service Experience
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Unnecessary Flushing Services, Additive Recommendations and Proper Utilization of GM Goodwrench Maintenance Schedule to Enhance Customer Service Experience
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about the percentage of UV protection or tint offered by the windshield or side glass. Technician should be advised Windshield reduces UV rays down to 4% or less. Front side door glass reduces UV rays down to 35% or less. Windshields are SOLAR glass with a light transmittance of >/=70%. Front door glass are Solar glass with a light transmission of >/=70%. Rear door glass, quarter windows and back windows can use either Solar glass (>/=70%) or Privacy glass, which has a light transmittance of 20%.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down, remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics. Technician may need to contact General Motors Technical Assistance Center depending on the STID, Station ID, or OnStar Customer Identifier.
Source components: ELECTRICAL SYSTEM · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about the new fluids available for axle service and clarifies usage. Technician will use the chart to determine the proper axle lubricant to use.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partech for assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
BUICK/CADILLAC/CHEVROLET/GMC/PONTIAC/ SATURN: THERE IS FLUID LEAKING FROM POWER STEERING SYSTEM, ALONG A FLUID LEAK IN FRONT OF VEHICLE UNDERNEATH AND SHOULD BE INSPECTED, CLEANED AND IDENTIFIED BEFORE REPAIRING OR REPLACING. MODEL 2010-14 LACROSSE, 2011-14 REGAL, 2007-14 ESCALADE, SUBURBAN, TAHOE, YUKON, YUKON XL, YUKON DENALI, YUKON DENALI XL, 2013-14 XTS, 2005-14 MALIBU, 2007-13 AVALANCHE, SILVERADO, SIERRA, 2006-10 G6, 2007-09 AURA. *PE
Source components: STEERING:HYDRAULIC POWER ASSIST SYSTEM · STEERING:HYDRAULIC POWER ASSIST:POWER STEERING FLUID.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provide policy information on GM of Canada New Vehicle Limited Warranty Tire Program and Global Warranty Management (GWM) Submission Information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provide policy information on a revised customer concern not duplicated/verified labor operation numbers and how to submit CCND.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM · EQUIPMENT ADAPTIVE/MOBILITY · EQUIPMENT:APPLIANCE:AIR CONDITIONER · EQUIPMENT:ELECTRICAL · POWER TRAIN:AXLE ASSEMBLY · SERVICE BRAKES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the OnStar system will not connect. Technician should record module info per the latest version of PIC4310 and contact General Motors Technical Assistance Center.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that some vehicles may have a Service Engine Soon lamp, engine misfire on cylinder 1, 4, 6, or 7 and/or tick noise. Technician will follow service information diagnosis first. If service information diagnosis does not isolate the cause of this concern perform a cylinder deactivation active fuel management system compression test in service information. If the running compression of the misfiring cylinder stays below 25 Pounds per Square Inch regardless of the active fuel management solenoid being commanded on or off, an active fuel management lifter is mechanically collapsed/stuck or unlocking as soon as the engine is started. Replace all active fuel management lifters, and all plastic lifter guides. Also perform the cylinder deactivation active fuel management Valve Lifter Oil Manifold Diagnosis and Testing in Service Information. If it isolates a concern with the Valve Lifter Oil Manifold, replace it and reevaluate the concern. The active fuel management lifters can also be monitored for proper operation by carefully inspecting the cylinder 1, 4, 6, and 7 rockers and valves while cranking or briefly and safely running the engine with the valve covers removed. If the valve or valves of an active fuel management cylinder stop moving while doing this test, the active fuel management lifter is causing the concern. For 2008-2009 Full Size Truck/SUV or a 2007-2009 Chevrolet Tahoe with the Police Package reprogram the Engine Control Module. On the 2008-2009 Pontiac G8, 2010-2011 Camaro, and 2007-2010 Full Size Trucks with active fuel management, also determine if the active fuel management pressure relief valve shield that is listed in the latest version of 10-06-01-008 has ever been installed. On passenger cars with the LS4 engine, determine if the updated oil pan gasket that is listed in the latest version of 11-06-01-007 has been installed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the Valve Assembly part number 24255209 and Valve Body part number 29544409 have been removed from the General Motors Product Quality Center parts restriction.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician vehicles with a slight rough idle. Technician should compare the concern with a like vehicle. If the concern is worse than a like vehicle, technician should follow published Service Information diagnosis and repair as necessary.
Source components: STEERING:LINKAGES:ARM:IDLER AND ATTACHMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary information bulletin provides information on poor or no transmitter range when using the remote keyless entry (RKE) and/or remote vehicle start (RVS).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary information bulletin provides a procedure to remove, update and reinstall the rear side door window reveal molding due to the exterior paint finish is chipped, cracked or scratched around the rear corners of the rear side door window outer sealing strip (reveal molding).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about an owner that may request to have a different style mirror installed on their vehicle or request a different mirror before they purchase the vehicle. Swapping mirrors on vehicles equipped with Side Blind Zone Alert, Regular Production Option Code UFT, is not recommended. On other vehicles tech will need to verify if the vehicle is equipped with door modules or not. On vehicles with door modules technician will need to contact Techline Customer Support for new calibrations for both doors. On vehicles not equipped with door modules no calibrations are needed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an audible engine whine noise at 1500-1800 revolutions per minute. Technician will need to check the coolant level, remove serpentine belt to verify noise goes away, rotate the thermostat 90 degrees and retest, then replace thermostat and retest. Technician will replace the water pump if there is no change.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Technician may find Diagnostic Trouble Codes P0420 and or P0430 stored. Technician should be advised that the catalytic converter efficiency Diagnostic Trouble Codes P0420 and P0430 are disabled for the first hour of engine run time to allow break-in of the catalytic converter. Technician will need to use a Tech2 to check the verify engine run time on the Engine Hour Meter in the Instrument Panel Cluster Data Display/Data 1 List in the scan tool match. If the engine run time is less than one hour, the battery may have been disconnected, or another vehicle power loss event may have occurred, during vehicle manufacturing. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle. If the catalytic converter was replaced and the Diagnostic Trouble Codes set it may be a result of the engine run time restrictions no longer being in place since the vehicle is no longer new. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle.
Source components: ENGINE AND ENGINE COOLING · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
GM: IF THE SERVICE SUSPENSION SYSTEM IS DISPLAYED ON THE DIC, THE TRIM HEIGHT MAY BE INCORRECT, LOOSE COMPRESSOR INLET HOSE, OR THE COMPRESSOR SELF TEST MAY BE INOPERATIVE. ALSO INCLUDED SUBURBAN LD MY 2001-2013, YUKON DENALI XL MY 2013, YUKON XL LD 2001-2013 *JS
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have low oil pressure, no oil pressure, and/or engine noise. Technician will need to replace the oil pump, flush the oil cooler lines.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a malfunction indicator light or service anti-lock brake system message displayed in the Driver Information Center. Technician may find Diagnostic Trouble Code C0055 or P2771. Technician will need to check for excess movement of the tone wheel or output shaft.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a revision for 12-02-32-002 to add the 2013-2014 model years, add noise as a possible condition and add a Note in the Instructions section.
Source components: STEERING · STEERING:HYDRAULIC POWER ASSIST:POWER STEERING FLUID.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Service Suspension System message on the Driver Information Center and the rear suspension ride height is incorrect. Technician will find Diagnostic Trouble Code C0696 or C0711 set in Electronic Suspension Control. Technician will need to inspect air compressor assembly for wire damage and repair any damage do not replace the complete air compressor assembly. Some vehicles may have a Service Suspension System message on the Driver Information Center and may also comment that the rear suspension ride height may be low under a heavy payload. Technician will follow published Service Information diagnostics and if determine if the sensor needs to be replaced technician will need to replace a complete air filter, dryer, and sensor assembly. Some vehicles may have a loose hose hanging down in the left rear of the vehicle. Technician will replace the auto leveling compressor air inlet filter and hose assembly. Also some vehicles may have automatic level control compressor is no longer performing a self-test at start up. Be advised the automatic level system normally will not or very infrequently cycle the compressor at key up.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Power Steering Noise or Fluid Leak from Power Steering Pump, Gear or High Pressure Pressure Hose During Extreme Low Temperature Operation (Replace Power Steering Fluid)
Source components: BACK OVER PREVENTION · POWER TRAIN · SERVICE BRAKES · STEERING · STEERING:HYDRAULIC POWER ASSIST:HOSE, PIPING, AND CONNECTIONS · STEERING:HYDRAULIC POWER ASSIST:POWER STEERING FLUID · STEERING:HYDRAULIC POWER ASSIST:PUMP.