Original record summaries, dates and identifiers for this model-year. Records 501–600 of 1,230, ordered newest first. Dated records on this page: Apr 15, 2019–Feb 28, 2020.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Feb 28, 2020Service Bulletin/Repair Instructions
040601029J
NHTSA communication ID: 10173416
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin explains Unscheduled Supplemental Services (including Flushing Services and Additives) and the Proper use of GM Simplified Maintenance Schedules.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to replace the upper and lower valve body housings to correct launch shudder, 2-3 Upshift or 3-2 Downshift concerns.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides information on the tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provide policy information to cover GMs policy on performing GM covered vehicle services and maintenance on vehicles originating/sold in Canada.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact PARTECH and/or the Techline Customer Support Center for additional support.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides retail, wholesale and fleet personnel with General Motors recommendations for customer concerns related to wheel alignment.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information to dealership personnel for new vehicles with less than 1,000 miles that may not pass California smog inspection or smog inspection in other states.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Warranty Administration bulletin provides information on customer vehicles concern results in a manufacturer repurchase from the customer, GM depends on the dealership to host and administer the repurchase closing and intake of the returning vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA) (US dealers only).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary information discusses potential for a code C0010.5A to store in the brake controller which appears to be setting falsely or is induced by the customer.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
NHTSA source summary · Original PDF not reviewed by Recallfolio
N192266180 - Special Coverage - On some 2010-2012, and 2014-2017 model year Chevrolet Equinox and GMC Terrain vehicles, a link ball socket in the wiper transmission may separate. If this were to occur, the driver would experience a sudden loss of wiper function. Dealers are to replace the front wiper module with the latest version with improved sockets and a new water shield. The repairs will be made at no charge to the customer.
Source components: ELECTRICAL SYSTEM · VISIBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary information bulletin provides information om Service Programming System (SPS) Error Codes (E4398, E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2 software to aid in diagnosing automatic transmission concerns. TAC is requesting the GDS2 session logs be sent in before the dealer contacts TAC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides repair information to correct a customer concern of HVAC Pop Up on Infotainment Screen Blank, Displays Red Box, or Has Incomplete Information After Initial Start Up.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to perform inspections to determine if the engine needs to be replaced as opposed to just internal parts for knocking, rattle, squeak and/or squeal type noises from engine.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead Seat Corrosion.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
Source components: SERVICE BRAKES, AIR:ANTILOCK · WHEELS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the information found in the service manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vibration complaints that are one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a Pre-Repair Authorization (PRA) (US dealers only).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact PARTECH and/or the Techline Customer Support Center for additional support.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure on diagnosing and repair moisture/ice and possibly contamination/debris in the SAI system and how to clean it out.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This diagnostic tip advises the tech to check if the upstream O2 sensor has been replaced with a faulty or aftermarket sensor and how to verify if the sensor is the cause of the concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary information bulletin provides information om Service Programming System (SPS) Error Codes E4398, E4399, E4403, M4404, M4413, E4414, E4423, E4491 or E6961).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides policy information, proper labor operation selection and causal part identification for warranty transactions (U.S. Only).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulleting provides Wiring, Terminal and Connector Repair Information including how to determine the Service Part Number in eSI and how to locate the part(s) in the EPC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear due to seeing grease or sealant on certain locations on the gear.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits. Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact Partech and/or the Techline Customer Support Center for additional support.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have oil mixed in with the engine coolant. Technician will need to inspect the oil cooler if equipped for possible leaking into the cooling system through the radiator. If no issue found replace the engine as well as all rubber coolant hoses.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to flush and bleed power steering system to correct a power steering noise or fluid leak concern that is caused during extremely low temperatures.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive disk on gasket sealing surfaces or reused parts.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper service or aftermarket calibrations.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have may a helicopter type noise when a rear window is lowered. This is a normal characteristic of this vehicle, but the concern can be minimized by lowering a front door glass approximately 1 to 2 inches.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Code P2097 or P2099. Technician will need to perform an injector balance or Active Fuel Injector Tester prior to going further. Technician will also need to check for a small leak in the exhaust if published Service Information diagnostics does not lead to a resolution.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin advises of a new fuel injection kit used for decarbonizing the intake valves, and explains how toptier fuels should be used to reduce carbon build up.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provide policy information to cover GM's policy on performing GM covered vehicle services and maintenance on vehicles originating/sold in Canada.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician to not remove the torque converter bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information on a rattle, tick, or knock type noise. Any drivability concerns they should be addressed prior to the following diagnostic progression. A sound file or video with sound of the noise needs to be made prior to dis-assembly to help isolate to one area in the engine. There are four different steps to diagnosis the concern. This communication was updated to include the 2017, 2018, and 2019 model years.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a blower speed knob only goes to 8 with less than expected high blower speed air flow. Technician should not replace any parts for this concern. Dealer should advise the customer to turn the ECO button Off and On at different blower speed settings 6 through 8 and note the change in the audible sound and air flow. This is a new enhancement to improve fuel economy when the ECO button is turned on.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates to the dealer an issue where the vehicle's engine may crank over unprompted and not start afterward. This is the result of hooking up the Active Fuel Injector Tool incorrectly on vehicles equipped with a direct fuel injection system. This Preliminary information instructs the dealer of a repair kit they received that will prevent this issue when installed correctly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have may a helicopter type noise when a rear window is lowered. This is a normal characteristic of this vehicle, but the concern can be minimized by lowering a front door glass approximately 1 to 2 inches.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the Navigation radio does not have a global positioning system location but OnStar is able to accurately locate the vehicle. Technician should check the installation of the COAX cables to be router correctly. Technician will gain access to the Radio or Human Machine Interface depending on the vehicle build. Install the EL-50334 test antenna to the Radio HMI and evaluate the operation. If the GPS signal is restored, inspect for incorrect coax routing as described above and if found, reroute the cable so it does not bypass the splitter.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technicians for diagnosing and repairing vehicles that have an issue with a pop noise from the fuel tank area after a cold start or Evaporative Emissions System purge. Technician will be able to use Global Diagnostic System 2 to duplicate the concern by commanding a purge and seal on the Evaporative Emissions System. Replacement of the auxiliary fuel pump module assembly will correct this concern.
Source components: ELECTRICAL SYSTEM · FUEL SYSTEM, GASOLINE.