Original record summaries, dates and identifiers for this model-year. Records 1,001–1,100 of 1,933, ordered newest first. Dated records on this page: Mar 31, 2015–Oct 5, 2015.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Oct 5, 2015Service Bulletin/Repair Instructions
PIP5331
NHTSA communication ID: 10114867
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles with a rattle, tick, or knock type noise. Technician will use chassis ears to listen to the right and left side of the engine and isolate which bank the noise is from. Technician should now remove the piston and rod assemblies from the affected bank to inspect for a loose rod bushing in the rod, or a loose wrist pin in the bushing. There should be no metal through the oil and a piston and rod assembly will repair this noise. If technician finds metal refer to the latest version of PIP5216. If no wrist pins or bushings are found loose and all other diagnostics for this type of noise has been exhausted then engine replacement may be necessary.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides retail, wholesale and fleet personnel with General Motors recommendations for customer concerns related to wheel alignment.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that Diagnostic Trouble Codes P0016, P0017, P0018, P0019, P0008 or P0009 may be set. Technician will need to inspect for loose timing chains or tensioners. If after following Service Information diagnostics the root cause is not found inspect the reluctor for the crankshaft sensor. If the reluctor has moved then replace crankshaft.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a ticking noise on cold start after sitting more than 6 hours. Technician will inspect the oil pump pick-up tube to block seal being compressed. It the seal is compressed replace the seal and retest.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the keyless entry is inoperative. Technician should inspect the ignition key cylinder door sticks in the up position. If the door is found open do not replace the ignition key cylinder, use a Lubriplate type of lubrication spray and lubricate the ignition key cylinder door. Insert the tip of the key in and out to verify the door of the cylinder is not sticking.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about a connectivity concern with Bluetooth after phone software is updated or after any vehicle updates for the radio or Human Machine Interface has taken place. Technician should delete all Bluetooth pairings and then reboot the Bluetooth device and the vehicle. After the vehicle and radio is booted back up repair the Bluetooth device.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the Turn By Turn directions may no longer be displayed after the Canada OnStar upgrade. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle that have a rattle noise from the rear lift gate on rough roads. Technician will need to inspect the lift gate wedges by opening the lift gate, insert paper between the body side & lift-gate side wedges, and then close the lift gate. If the paper cannot be removed, grease lift-gate side wedges. If the paper can be removed, reset the wedges by loosen lift-gate side wedge center screw to allow center portion to "ratchet" along internal detents freely, pull center adjustment portion of lift-gate side wedges to full downward position, close lift-gate to full latch engagement then use power to close lift-gate system (if available), close manually on non-power lift gates and do not slam, open lift gate, and pull the center adjustment portion down one additional detent & torque screw 5.0 newton meters if wedge adjustment does not have enough travel for the one additional detent add washer under the two lift-gate side wedge attachments to shim as required. Now to inspect the lift gate wedges by opening the lift gate, insert paper between the body side & lift-gate side wedges, and then close the lift gate. If the paper cannot be removed, grease lift-gate side wedges. If the concern is still present adjust lift-gate latch striker.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the incoming caller ID may no longer be available or displayed after the Canada OnStar upgrade. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician to help determine if the vehicle is equipped with factory or aftermarket Compressed Natural Gas, Liquefied Petroleum Gas, or Bi-Fuel Systems. Technician will check for the Vehicle Emission Control Information Label. By using the engine Regular Production Option Code as well as the Vehicle Emission Control Information Label, technician can confirm the vehicle has a factory installed alternative fuel system or who the manufacturer is of the aftermarket fuel system.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp, service Antilock Braking System, Service Stabilitrak, Service All Wheel Drive, Service Suspension Control, or Hard Steering. Technician may find the following Diagnostic Trouble Codes stored C0196, C0186, C0287, C0710, C0045, C0050, C0800, U0077, U0074, U0125, U0126, U0100, U0101, U0121, U0415, U0432, U0121, and or U0140. Technician should inspect X411 connector for damage or corrosion. Technician will replace any terminals with damage or corrosion.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CHEVROLET/GMC: IN FOOTWELL AREA OF SOME VEHICLES, IN DRIVER OR PASSENGER SIDE, CARPET/FLOOR IS WET DUE TO SEALING THAT WAS INSUFFICIENT OR INCOMPLETE IN FRONT ROOF OF BODY SIDE SEAMS OUTER PANEL. MODEL 2010-16 TERRAIN, EQUINOX. *PE
Source components: STRUCTURE · STRUCTURE:FRAME AND MEMBERS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have may a helicopter type noise when a rear window is lowered. This is a normal characteristic of this vehicle, but the concern can be minimized by lowering a front door glass approximately 1 to 2 inches.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles with the rear wiper and/or the front rain sense wipers turn off when the vehicle is shifted to neutral. This is the normal operating characteristic of this vehicle. This is called Car Wash Mode.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin adds the 2015 and 2016 Model Years to repair information to correct a customer concern of finding a wet carpet/floor in the driver or passenger footwell area.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a blower speed knob only goes to 8 with less than expected high blower speed air flow. Technician should not replace any parts for this concern. Dealer should advise the customer to turn the ECO button Off and On at different blower speed settings 6 through 8 and note the change in the audible sound and air flow. This is a new enhancement to improve fuel economy when the ECO button is turned on.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides dealership personnel with policy and procedure requirements for essential tools that include consumable parts (U.S. Only).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about iPhones will not always autoconnect through Bluetooth to the vehicle. If the vehicle has more than one device listed in the Bluetooth device list, and the last device used was an Apple product, the Apple products will not autoconnect. The system will connect to one of the other devices instead. This concern is usually noticed after Retained Accessory Power has cancelled and the vehicle has gone to sleep. Advise the customer that they will need to update their Apple device to the latest operating system.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides repair information to correct a customer concern of loss of power steering assist, hard to steer, and/or "Service Power Steering" message on in DIC.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · POWER TRAIN · STEERING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about some vehicles that may have a concern of Bluetooth music skipping. This condition is a normal operating characteristic of the vehicle. Streaming music through Bluetooth uses a lot of the radio's processing resources. If the radio is also dedicating a large amount of resources to other applications such as navigation, booting, or XM Weather the Bluetooth audio may hesitate/skip as the system is being heavily loaded.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will check Global Warranty Management system for customer satisfaction program 15086 status. If the status of the customer satisfaction program 15086 was not completed follow the steps to get the Telematics Communication Interface Control Module replaced. If the status of customer satisfaction program 15086 is found completed contact General Motors Technical Assistance Center OnStar group for further assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a creak, pop, tick or itch type noise from the center of the dash or base of the windshield area while driving the vehicle. Technician will need to gain access to the center bracket under the cowl. Technician will need to apply 3M? Urethane Sealer part number 08609, between the bracket and bulkhead and around the bracket itself.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information to advise dealers about seat belt buckles not operating and/or seat belt warning light illumination, as well as difficulty latching and unlatching the buckle or the buckle release button sticking.
NHTSA source summary · Original PDF not reviewed by Recallfolio
BUICK/CADILLAC/CHEVROLET/GMC: DUE TO AN IMPROPER JUMP START, THE POWER STEERING FUSE WAS EITHER BLOWN OR FAILED, CAUSING A HARD STEERING. OR LOSS OF POWER STEERING ASSIST. MODEL 2013-16 LACROSSE, REGAL, MALIBU, 2010-13 EQUINOX, TERRAIN, 2014-15 ELR, 2014-16 IMPALA, 2012-15 VERANO, 2011-15 CRUZE, VOLT. *PE
Source components: STEERING · STEERING:ELECTRIC POWER ASSIST SYSTEM · STEERING:HYDRAULIC POWER ASSIST SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version. If the Firmware Over-the-Air version on the scan tool equals 6708 the technician will need to contact General Motors Technical Assistance Center for further assistance. If the Firmware Over-the-Air version on the scan tool is lower than 6708 Dealer can order the part thought the Instrument Sales and Service website process.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about customers that may complain of various concerns when using Bluetooth components. Technician should use the Preliminary Information to gather information from the customer on their Bluetooth device and the concern they are having before calling General Motors Technical Assistance Center.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides repair information for the correction of a customer concern of short duration musty odors emitted from the HVAC system at vehicle start-up in hot, humid conditions.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:APPLIANCE:AIR CONDITIONER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician of diagnostic instructions to take when the key will not fold into the fob or will not stay in the folded position. The technician may comment that the key in the fob will not fold close or stay latched closed. Damage to the folding mechanism could result from storing the key in the door lock cylinder and accidently bumping or making contact with the key fob. Please advise all dealer personnel to refrain from storing the key in the door lock even for brief periods.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides technicians with information to assist in identifying operating characteristics of manual transmissions that repair attempts will not change.
Source components: POWER TRAIN:MANUAL TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician of a concern where the Onstar® menu is missing from the radio display. Pressing the white Onstar® push to talk button and say hide Onstar® menu will hide the menu and saying unhide menu will make the menu come back again.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides dealership personnel with information on new vehicle Pre-Delivery Inspection (PDI) process and to encourage delivering quality vehicles and generating higher CSi scores.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides dealership personnel with information on interior cleaning of Instrument Panel (IP), hard or plastic surfaces, seats, carpet, leather, vinyl, fabric cleaner, stain remover, restorer and product availability.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician of an engine power reduced message on the driver information center after performing the Canada Onstar® 4G upgrade. If the concern is present park the vehicle outside and call General Motors Technical Assistance Center.
Source components: EQUIPMENT:ELECTRICAL · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician the steps on how to diagnose and repair vehicle that may have Service Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Code P219A. Technician should use published Service Information diagnostics for Diagnostic Trouble Code P219A. If the Global Diagnostic System 2 fuel injector balance test does not isolate a cause for this concern, perform the Fuel Injector Diagnosis (w/CH47976 and CH-47976-500) in Service Information and evaluate for a rich or lean fuel injector.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information to dealership personnel regarding warranty codes generated by EL-50313 Midtronics GR8 Battery Tester/Charger required for claim processing on labor operations 4041510, 4041520 and 250 mile/400 km labor operation restriction (North America ONLY).
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin adds the 2015-2016 model years to repair information to correct a customer concern of inaccurate or slow response of outside air temperature display.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician the steps to diagnose and repair vehicles that have intermittent hard start Service Engine Soon Malfunction Indicator Lamp or low oil pressure lamp on. Technician may find Diagnostic Trouble Codes P0261, P0264, P0267, P0270, P0273, P0276, and or P0641. Technician should inspect the engine harness routing the Engine Control Module and the upper rear of the engine. Technician should repair and wires that are damaged from the harness rubbing. After the wires are repaired protective wrap, and reposition the harness away from the engine.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information to dealership personnel regarding original equipment battery part numbers and AC Delco replacement battery approved warranty part numbers.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides repair information on Electronic Brake Control Module (EBCM) reprogramming to correct a customer concern that during the activation of the Forward Collision Alert System (FCA), the car feels as if it is prematurely decelerating.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides repair information for repairing the IP to body harness connector to correct a customer concern for intermittent Malfunction Indicator Lamp (MIL) illuminated with Reduced Engine Power displayed and DTC P2138 set.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about being unable to receive OnStar ?Over The Air? updates. Technician will need to press the OnStar button and verify they have an active account and that the call connects with data and location.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have had multiple repair attempts are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides dealership personnel with Global Warranty Management (GWM), Warranty Parts Center (WPC), and Parts Return Program information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician the steps on how to diagnose and repair vehicle that may have Service Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Code P219A. Technician should use published Service Information diagnostics for Diagnostic Trouble Code P219A. If the Global Diagnostic System 2 fuel injector balance test does not isolate a cause for this concern, perform the Fuel Injector Diagnosis (w/CH47976 and CH-47976-500) in Service Information and evaluate for a rich or lean fuel injector.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides a windshield molding lubrication repair to correct a customer concern of a creak or pop type noise coming from the windshield area during cold ambient temperatures.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have the OnStar wireless fidelity inoperative. Technician will need to contact General Motors Technical Assistance Center with a scan tool connect to the vehicle for further assistance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a knock noise, seized engine, lower end squeak or squeal from the engine. Technician will inspect the oil control solenoids for metal debris. Also inspect for damage to the cam caps Journals and camshaft journals on the heads. The check the timing chain idler sprockets for stiffness when turning. If any of these instances would be a cause to replace the engine instead of repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin adds the 2016 model year to repair information for a customer concern of Malfunction Indicator Lamp (MIL) on, Reduced Power Mode on, DTC(s) set, and/or poor performance/shifts.
NHTSA source summary · Original PDF not reviewed by Recallfolio
14232A - SPECIAL COVERAGE (WARRANTY TRANSACTION INFORMATION REVISED). SOME 2012-2014 MODEL YEAR (MY) BUICK VERANO, 2011-2014 MY CHEVROLET CRUZE AND VOLT, 2010-2014 MY CHEVROLET EQUINOX AND GMC TERRAIN, AND 2013-2014 MY CHEVROLET MALIBU VEHICLES, EQUIPPED WITH ELECTRONIC POWER STEERING (NJ0/NJ1), MAY HAVE INCREASED FRICTION IN THE STEERING SYSTEM. THIS COULD CAUSE THE STEERING WHEEL TO STICK IN THE STRAIGHT-AHEAD POSITION AFTER DRIVING LONG DISTANCES ON A STRAIGHT HIGHWAY. THE STEERING WHEEL CAN BE TURNED BUT IT MAY REQUIRE INCREASED EFFORT. DEALERS ARE TO 1) REPLACE THE STEERING GEAR ON 2010-2012 MODEL YEAR VEHICLES; OR 2) REPROGRAM THE POWER STEERING CONTROL MODULE ON 2013-2014 MODEL YEAR VEHICLES.
Source components: STEERING:ELECTRIC POWER ASSIST SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version. If the Firmware Over-the-Air version on the scan tool equals 6708 the technician will need to contact General Motors Technical Assistance Center for further assistance. If the Firmware Over-the-Air version on the scan tool is lower than 6708 Dealer can order the part thought the Instrument Sales and Service website process.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about the rear view camera options on the vehicles equipped with rear view camera. The rear view camera brightness can be adjusted on some models while the transmission is in reverse and using the Menu or Select button. To turn off or on the guidelines in the rear view camera, use the radio display Config icon then Display, then the guidelines option.
Source components: BACK OVER PREVENTION: CAMERA SYSTEM · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have difficulty filling the fuel tank and / or experience fuel spit-back when fueling. Technician will follow published Service Information diagnostics to determine a root cause. If Service Information diagnostics does not isolate the cause of this concern, dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp, service Antilock Braking System, Service Stabilitrak, Service All Wheel Drive, Service Suspension Control, or Hard Steering. Technician may find the following Diagnostic Trouble Codes stored C0196, C0186, C0287, C0710, C0045, C0050, C0800, U0077, U0074, U0125, U0126, U0100, U0101, U0121, U0415, U0432, U0121, and or U0140. Technician should inspect X411 connector for damage or corrosion. Technician will replace any terminals with damage or corrosion.
NHTSA source summary · Original PDF not reviewed by Recallfolio
GEMS/CHEVROLET/BUICK: SEE DOCUMENT SEARCH BUTTON FOR OWNER LETTER. ON SOME VEHICLES, THE STEERING WHEEL WOULD STICK IN STRAIGHT AHEAD POSITION AFTER LONG DISTANCE DRIVING ON STRAIGHT HIGHWAY DUE TO STEERING SYSTEM HAVING AN INCREASED FRICTION AND TURNING WOULD BE AN INCREASED EFFORT. MODEL 2011-2014 CRUZE, VOLT, 2010-14 EQUINOX, TERRAIN, 2012-14 VERANO, 2013-14 MALIBU. *PE UPDATED 11/6/15. *PE
Source components: STEERING:HYDRAULIC POWER ASSIST SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician of a customer concern where the heated seat indicator light is not functioning or the heated seats are not up to operating temperature during a remote vehicle start event. This is normal operation of the heated seat during a remote vehicle start event. The electronic climate control module is not in a complete wake up state during a remote vehicle start mode and will not enable the light emitting diode. After a cold soak below 32 degrees Fahrenheit the seat will not get hot in the 10 minutes or less of the remote vehicle start mode. This is due to the fact that the heat element is not in direct contract with the seat surface while the seat is unoccupied and the foam below the heater is full cold insulating air which takes time to heat up. Technician is to communicate to the customer this condition is a normal operating characteristic of their vehicle. It will not impact the designed performance or reliability of the vehicle. Please share this information with the customer, including a copy of this message.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician of part numbers that are missing from the service information documents. The following part numbers are for a cam nut that is available to adjust the rear toe 11519455, 11562237, 11570574.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician for vehicles with an intermittent malfunction indicator lamp on, the interior lamps are inoperative and or the lift gate is inoperative. Diagnostic trouble codes U0078, U0140, U0151, U0155, U0164, U0198, or U0230 can be present. Inspect the body harness connector X901 for water intrusion or corrosion. Repair the connector and terminals as required.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides technicians with updated information to help identify the differences between what is considered a fluid leak, and what is considered seepage.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides repair information for low beam headlamp bulb diagnosis/replacement to correct a customer concern that the low beam headlamp is inoperative.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician with information regarding high misfire rates always on #1 cylinder. A customer may complain of misfires or roughness on cold start up with a P0300 diagnostic trouble code. Technician is to add coolant dye to the system and run the engine through warm up to circulate the dye. Pressurize the cooling system after a cold soak and inspect the cylinder with a bore scope for coolant dye. Dye is used to identify coolant over residual fuel being that might be left in the cylinder. The technician is not to replace the cylinder head as it will not correct this concern. In some cases it is necessary to remove the head for inspection. Do not replace the engine for small surface pock marks or a pitting appearance this is normal and do not connect to coolant passages. Usually if porosity is present there will be a break in the carbon ring. Only replace the engine if true porosity is found. Technician is to call Product Quality Center with the latest version of bulletin 02-07-30-029 if porosity is found and engine replacement is required.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician to follow this Preliminary Information if there is a diagnostic trouble code P00C6 and or P228C set and normal Service Information diagnostics didn?t lead to a repair. Technician is to recheck the terminals at the Engine Control module for fit and tension as well as the crimp to the wire. The engine control module terminals to inspect are in the X2 connector. Inspect terminal number 3, 18 and 19 for the fuel rail pressure sensor and in the X3 connector terminals 16 and 32 for the high pressure fuel pump. The diagnostic trouble codes could set with as little as a 2 ohm resistance reading on these circuits. If any concerns are found replace the affected terminals and verify the repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician to insure that global diagnostic service 2 diagnostic packages are up to date prior to learning the steering angle sensor for a diagnostic trouble code C710 symptom code 71 set in the electronic brake control module or the power steering control module. When rechecking for diagnostic trouble codes a U0074 U0077, U0180D, U01293, U0126, U0125, C0186, C0196, or C0287 are set and will not clear diagnose the Chassis bus. If no fault is found in the chassis bus check for an multiple diagnostic interface to data link connector issue. Technician is to try a different multiple diagnostic interface cable and attempt the steering angle sensor learn again following service information instruction then try to clear the codes again.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician to not replace any parts for the XM weather, fuel, or movies tabs not working or no information coming up on the display. Apologize to the customer for the inconvenience and let them know that General Motors is working on a solution for this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician for a forward collision alert or lane departure warning inoperative with no diagnostic trouble codes stored. This concern could be caused by an aftermarket windshield. Verify there is the General Motors logo in the lower right corner of the windshield.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician for vehicles with a malfunction indicator lamp on, service stabilitrak, power steering or vehicle soon message displayed on the drivers information center. The technician may find the following diagnostic trouble codes U0073, U0100, U0101, U0121 U0140 C0045, C0050 in the body control module, electronic brake control module, engine control module, or the transmission control module. There may be multiple loss of communication codes current or history for high speed General Motors Local Area Network. Inspect the connections at connector X411 for corrosion due to the location of the connector under the vehicle by the rear wheel.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CHEVROLET/GMC: DUE TO POSSIBLE AFTERMARKET WINDSHIELD, SOME VEHICLES MAY BE EXPERIENCING AN INTERMITTENT WARNING PERTAINING TO AN INOPERATIVE LAND DEPARTURE WARNING AND/OR FORWARD COLLISION ALERT. MODEL 2013-15 EQUINOX, TERRAIN. *PE
Source components: FORWARD COLLISION AVOIDANCE · LANE DEPARTURE: WARNING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
GMC/CHEVROLET: A COMMUNICATION FAULT, REGARDING SERVICE STABILITY TRACTION AND ABS REAR WHEEL SPEED DTC OR CHASSIS EXPANSION BUS, WHICH IS RELATED TO AN INTERNAL WIRE BREAK INSIDE WIRE HARNESS INSULATION TO X411 CONNECTOR. MODELS 2010-2012 CHEVROLET EQUINOX & GMC TERRAIN. *PE UPDATED ON 5/9/2013. *KB UPDATED 7/10/2013. *KB UPDATED 2/1/16. *PE
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have may an intermittent Service Traction/Stability, ABS indicator or Service All wheel Drive message on the Driver Information Center. Technician may find Diagnostic Trouble Codes U0125 00 U0074 00 U0073 and or C0045 C0050 symptom 06. Technician will need to inspect the X411 connecter for a wire break inside the wire harness. Also inspect the wire harness insulation within 1 inch of the X411 before and after connecter. Repair any damaged wiring to correct the concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have may a helicopter type noise when a rear window is lowered. This is a normal characteristic of this vehicle, but the concern can be minimized by lowering a front door glass approximately 1 to 2 inches.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles with the rear wiper and/or the front rain sense wipers turn off when the vehicle is shifted to neutral. This is the normal operating characteristic of this vehicle. This is called Car Wash Mode.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary informational bulletin provides repair information to correct a customer concern of Iitermittently key will not rotate in door or ignition lock cylinder.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about Apple devices is inoperative or freezing when using the device via USB cable after an IOS8.x.x update. Technician will need to delete the radio from the phone and the phone from the radio. Also close out all apps on the device if it is an iPhone.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information to assist dealership personnel with the identification of vehicle headlamp, tail lamp, license lamp or fog/driving lamp damage that are not considered warrantable.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides technicians with information to help identify the differences between what is considered a fluid leak, and what is considered seepage.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician about the calculation and operation of the engine oil life monitor. The monitor calculates the percent of oil life remaining, based on 3 pathways. The first pathway for oil life calculation is engine revolutions. The second pathway for oil life calculation is the mileage form the last rest for all General Motors powertrains except the Volt. The third pathway for oil life calculation is the amount of time the oil is in the engine. The Volt uses a 2 year timer instead of 1 year. It also uses the engine revolution counter. It does not use the mileage pathway to count down.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a high pitched whistle or wind noise from the driver?s side mirror area between speeds 25 to 52 mph. Technician will need to use a rubber mallet and lightly tapping on the belt molding moving it toward the (A) pillar area. Then remove the belt molding, use a suitable piece of rubber and glue it to the back side of the of the belt molding to extend it to fill the gap.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technicians for diagnosing and repairing vehicles that have an issue with a pop noise from the fuel tank area after a cold start or Evaporative Emissions System purge. Technician will be able to use Global Diagnostic System 2 to duplicate the concern by commanding a purge and seal on the Evaporative Emissions System. Replacement of the auxiliary fuel pump module assembly will correct this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information to service personnel on the critical importance of installing the correct replacement spin-on oil filter when servicing.