The manufacturer’s record · Page 3 of 7
Original record summaries, dates and identifiers for this model-year. Records 201–300 of 680, ordered newest first. Dated records on this page: Oct 30, 2017–Nov 22, 2019.
Back to 2009 GMC SIERRA 1500 problems & recallsThis archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
NHTSA communication ID: 10169345
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides repair information to correct a customer concern of Clock Shows Dashes and Cannot be Set After Battery Disconnect.
Source components: ELECTRICAL SYSTEM.
Source record 10169345 at NHTSANHTSA communication ID: 10169038
NHTSA source summary · Original PDF not reviewed by Recallfolio
This SKU is a Fuel Pump Driver Module. The customer communication requested return of unsold inventory to inspect the software. The software may have a fault where the readiness monitors are stuck in the not-ready or incomplete position. The readiness monitors will not cause performance or emissions issues but will prevent the emissions scanning tools from confirming the module is performing correctly, causing the vehicle to fail state required emissions tests.
Source components: ELECTRICAL SYSTEM:SOFTWARE · FUEL SYSTEM, GASOLINE.
Source record 10169038 at NHTSANHTSA communication ID: 10168206
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to apply grease to the leaf springs to correct a condition of a squeak noise from the metals making contact.
Source components: SUSPENSION:FRONT:SPRINGS:LEAF SPRING ASSEMBLY.
Source record 10168206 at NHTSANHTSA communication ID: 10167458
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a bump feel or clunk noise at a stop or on launch. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle. The bump clunk issue may be due to fuel movement in the fuel tank when not completely full. The condition is eliminated after completely filling the fuel tank.
Source components: FUEL SYSTEM, GASOLINE.
Source record 10167458 at NHTSANHTSA communication ID: 10168207
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for dealers how to submit a product information report (PIR) (Canada Only).
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10168207 at NHTSANHTSA communication ID: 10168209
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on Clean Exhaust Filter See Owners Manual Now or Cleaning Exhaust Filter Keep Driving Until Message is Cleared messages Displayed on DIC, DTC P2463 May Be Set.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM.
Source record 10168209 at NHTSANHTSA communication ID: 10168175
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns.
Source components: POWER TRAIN.
Source record 10168175 at NHTSANHTSA communication ID: 10168208
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on key code security and information on GM key code look up applications.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10168208 at NHTSANHTSA communication ID: 10168205
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
Source components: ENGINE AND ENGINE COOLING.
Source record 10168205 at NHTSANHTSA communication ID: 10168204
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on comebacks prevention information and using customer concern verification sheets (CCVS).
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10168204 at NHTSANHTSA communication ID: 10164752
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have low oil pressure, no oil pressure, and/or engine noise. Technician will need to replace the oil pump, flush the oil cooler lines.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10164752 at NHTSANHTSA communication ID: 10163272
NHTSA source summary · Original PDF not reviewed by Recallfolio
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for causing multiple customer concerns that do not have other diagnostic methods to identify them.
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10163272 at NHTSANHTSA communication ID: 10163270
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to flush and bleed power steering system to correct a power steering noise or fluid leak concern that is caused during extremely low temperatures.
Source components: STEERING.
Source record 10163270 at NHTSANHTSA communication ID: 10163268
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with conductive finish.
Source components: ELECTRICAL SYSTEM · EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10163268 at NHTSANHTSA communication ID: 10163261
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
Source components: FUEL SYSTEM, DIESEL · FUEL SYSTEM, GASOLINE.
Source record 10163261 at NHTSANHTSA communication ID: 10163266
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2.
Source components: ENGINE · EQUIPMENT.
Source record 10163266 at NHTSANHTSA communication ID: 10163265
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure for re-torque the lead springs.
Source components: SUSPENSION:REAR:SPRINGS:LEAF SPRING ASSEMBLY · SUSPENSION:REAR:SPRINGS:LEAF SPRING ASSEMBLY:HANGER/BRACKET.
Source record 10163265 at NHTSANHTSA communication ID: 10162149
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn.
Source components: SERVICE BRAKES.
Source record 10162149 at NHTSANHTSA communication ID: 10162113
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information document advises technicians that a condition may occur with the listed vehicles where the radio clock may not display the time. Dealer technicians are advised of a temporary proicedure to get the clock to display until Engineering has developed the permanent repair. The listed Cadillac, Pontiac, and Corvette RPO codes do not have a temporary repair at this time as Engineering continues to work on the permanent repairs for those vehicles.
Source components: EQUIPMENT:ELECTRICAL.
Source record 10162113 at NHTSANHTSA communication ID: 10162106
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
Source components: ELECTRICAL SYSTEM.
Source record 10162106 at NHTSANHTSA communication ID: 10161036
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to help diagnose and repair vehicles with a rattle, squeak, clunk, thump, or bump. If published Service Information diagnostics do not lead to a repair for the concern. Technician should inspect the opposite side shock/strut for the cause of the concern.
Source components: SUSPENSION.
Source record 10161036 at NHTSANHTSA communication ID: 10161016
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information document advises technicians that a condition may occur with the listed vehicles where the radio clock may not display the time. Dealer technicians are advised of a temporary proicedure to get the clock to display until Engineering has developed the permanent repair. The listed Cadillac and Corvette RPO codes do not have a temporary repair at this time as Engineering continues to work on the permanent repairs for those vehicles.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT:ELECTRICAL.
Source record 10161016 at NHTSANHTSA communication ID: 10161011
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communicates to technicians that the Daytime Running Lamps (DRL's) or the auto headlamps will not shut off when using the daytime running lamp disable switch (Which is part of the headlamp switch), if the vehicles was built for Canada (RPO Z49). These vehicles were built with different software that doesn't allow the DRL's or Auto headlamp to be shut off. Canada law prohibits disabling daytime running lamps (DRL's) or auto headlamps.
Source components: ELECTRICAL SYSTEM · EXTERIOR LIGHTING:HEADLIGHTS.
Source record 10161011 at NHTSANHTSA communication ID: 10161004
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn.
Source components: SERVICE BRAKES.
Source record 10161004 at NHTSANHTSA communication ID: 10161929
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provide policy information to cover GM's policy on performing GM covered vehicle services and maintenance on vehicles originating/sold in Canada.
Source components: EQUIPMENT.
Source record 10161929 at NHTSANHTSA communication ID: 10161907
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC).
Source components: EQUIPMENT.
Source record 10161907 at NHTSANHTSA communication ID: 10160700
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information document advises technicians that a condition may occur with the listed vehicles where the radio clock may not display the time. Dealer technicians are advised of a temporary proicedure to get the clock to display until Engineering has developed the permanent repair. The listed Cadillac and Corvette RPO codes do not have a temporary repair at this time as Engineering continues to work on the permanent repairs for those vehicles.
Source components: EQUIPMENT.
Source record 10160700 at NHTSANHTSA communication ID: 10160683
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information document advises technicians that a condition may occur with the listed vehicles where the radio clock may not display the time. Dealer technicians are advised of a temporary proicedure to get the clock to display until Engineering has developed the permanent repair. The listed Cadillac and Corvette RPO codes do not have a temporary repair at this time as Engineering continues to work on the permanent repairs for those vehicles.
Source components: EQUIPMENT.
Source record 10160683 at NHTSANHTSA communication ID: 10160682
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
Source components: VISIBILITY:SUN/MOON ROOF ASSEMBLY.
Source record 10160682 at NHTSANHTSA communication ID: 10160663
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates an issue with aftermarket USB chargers causing SIR DTC's to set.
Source components: EQUIPMENT.
Source record 10160663 at NHTSANHTSA communication ID: 10160662
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the speedometer needle appears to be inaccurate. Dealer should advise the customer the specification for speedometer needle accuracy is +/- 2 MPH at any given speed when looking straight at the needle.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL.
Source record 10160662 at NHTSANHTSA communication ID: 10160660
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates the need for dealers to contact SPAC to obtain qualified parts to repair SIR light on with B0081 SYM4B after replacing PPS kit.
Source components: ELECTRICAL SYSTEM.
Source record 10160660 at NHTSANHTSA communication ID: 10160637
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about a customer?s request to remove or disable the Bi-Fuel Compressed Natural Gas system. General Motors does not condone the removal of the original equipped Compressed Natural Gas systems.
Source components: FUEL SYSTEM, GASOLINE.
Source record 10160637 at NHTSANHTSA communication ID: 10158861
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
Source components: ELECTRICAL SYSTEM:SOFTWARE · EQUIPMENT:ELECTRICAL · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10158861 at NHTSANHTSA communication ID: 10156942
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that the Serial Data Gateway Module (SDGM) may report "Crash Sense Failed" and the 300v Hybrid Battery Contactors will remain open until the Hybrid Powertrain Control Module's (HPCM) High Voltage (HV) DTCs are reset. And How to Reset.
Source components: ELECTRICAL SYSTEM:12V/24V/48V BATTERY · EQUIPMENT · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
Source record 10156942 at NHTSANHTSA communication ID: 10156912
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Technician may find Diagnostic Trouble Codes P0420 and or P0430 stored. Technician should be advised that the catalytic converter efficiency Diagnostic Trouble Codes P0420 and P0430 are disabled for the first hour of engine run time to allow break-in of the catalytic converter. Technician will need to use a Tech2 to check the verify engine run time on the Engine Hour Meter in the Instrument Panel Cluster Data Display/Data 1 List in the scan tool match. If the engine run time is less than one hour, the battery may have been disconnected, or another vehicle power loss event may have occurred, during vehicle manufacturing. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle. If the catalytic converter was replaced and the Diagnostic Trouble Codes set it may be a result of the engine run time restrictions no longer being in place since the vehicle is no longer new. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle.
Source components: ENGINE · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR.
Source record 10156912 at NHTSANHTSA communication ID: 10155073
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides the dealer with information on what to do when requesting a new key code for the customer.
Source components: EQUIPMENT.
Source record 10155073 at NHTSANHTSA communication ID: 10154312
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician that a whine noise heard from the automatic transmission fluid pan hear with the the key on and engine off, or for up to one minute after the vehicle has been shut off should be deemed a normal characteristic.
Source components: POWER TRAIN.
Source record 10154312 at NHTSANHTSA communication ID: 10154306
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
Source components: ENGINE AND ENGINE COOLING.
Source record 10154306 at NHTSANHTSA communication ID: 10154299
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
Source components: ENGINE AND ENGINE COOLING.
Source record 10154299 at NHTSANHTSA communication ID: 10154297
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates to the dealer an issue where the vehicle's inspection and maintenance monitors along with diagnostic trouble codes may reset unprompted due to the installation of an aftermarket fuel pump control module.
Source components: FUEL SYSTEM, GASOLINE.
Source record 10154297 at NHTSANHTSA communication ID: 10155069
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for aftermarket trailer brake controller added to their vehicle, OR in lieu of the factory integrated trailer brake controller (ITBC) (RPO JL1).
Source components: ELECTRICAL SYSTEM: INTEGRATED TRAILER BRAKE CONTROL · SERVICE BRAKES.
Source record 10155069 at NHTSANHTSA communication ID: 10155072
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides information on Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing and the procedures to turn the Transport Mode message On and Off.
Source components: ELECTRICAL SYSTEM:12V/24V/48V BATTERY.
Source record 10155072 at NHTSANHTSA communication ID: 10154289
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information document advises technicians that a condition may occur with the listed vehicles where the radio clock may not display the time. Dealer technicians are advised to contact General Motors TAC for further instructions for a temporary repair until Engineering has developed the permanent repair. The listed Cadillac and Corvette RPO codes do not have a temporary repair at this time as Engineering continues to work on the permanent repairs for those vehicles.
Source components: EQUIPMENT:ELECTRICAL.
Source record 10154289 at NHTSANHTSA communication ID: 10154628
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC).
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10154628 at NHTSANHTSA communication ID: 10154625
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on comebacks prevention information and using customer concern verification sheets (CCVS).
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10154625 at NHTSANHTSA communication ID: 10155055
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a listing of the parts availability for coax repair procedures and what is needed to complete some repairs.
Source components: EQUIPMENT.
Source record 10155055 at NHTSANHTSA communication ID: 10154629
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty admin bulletin explains to the technician additional information may be needed when submitting transactions when doing wiring repairs.
Source components: ELECTRICAL SYSTEM:WIRING.
Source record 10154629 at NHTSANHTSA communication ID: 10154627
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides policy information on required operating procedures.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10154627 at NHTSANHTSA communication ID: 10155010
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty bulletin provides labor operation numbers for customer concerns Not duplicated (CCND).
Source components: EQUIPMENT.
Source record 10155010 at NHTSANHTSA communication ID: 10154604
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
Source components: ENGINE AND ENGINE COOLING.
Source record 10154604 at NHTSANHTSA communication ID: 10154601
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have slack in one of the tailgate cables. Technician should not replace any parts for this concern. Please communicate to the customer this condition is a normal operating characteristic of their vehicle.
Source components: STRUCTURE:BODY:TAILGATE.
Source record 10154601 at NHTSANHTSA communication ID: 10155014
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S. Technical Assistance (TAC).
Source components: EQUIPMENT.
Source record 10155014 at NHTSANHTSA communication ID: 10154595
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides steps the technician will take to repair a no crank/no start concern with a diagnostic trouble code of B009F in the Serial Data Gateway Module equipped with Regular Production Option code HP2. The vehicle may exhibit a no crank or no start, or a Service Hybrid message with no codes. The technician will inspect the High Voltage Circuit Impact Detection sensor for water intrusion or corrosion at the weather pack. Inspect the High Voltage Circuit Impact Detection sensor for cracks or terminal corrosion and replace the sensor or terminals along with the weather pack seals if damage is found. If there is no damage found the technician will leave the sensor unplugged and power up the vehicle to induce a code, then power down the vehicle with the Tech 2 unplugged from the vehicle for two minutes. Clear the code and recheck for the message and codes, if the code resets the technician will replace the High Voltage Circuit Impact Detection sensor and terminals with terminated leads. Technician is to repeat the above steps to verify the concern is corrected.
Source components: ELECTRICAL SYSTEM.
Source record 10154595 at NHTSANHTSA communication ID: 10155013
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides technicians with information on available BCM calibrations to restore bulb outage detection on vehicles produced by a second stage manufacturer (Upfitter), and/or turn signals flash fast after factory box removed.
Source components: EXTERIOR LIGHTING.
Source record 10155013 at NHTSANHTSA communication ID: 10154575
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates to the dealers not to over look a possible leak from the Yoke,
Source components: POWER TRAIN.
Source record 10154575 at NHTSANHTSA communication ID: 10154572
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates of a program update to fix a bump when stopping
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10154572 at NHTSANHTSA communication ID: 10154566
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
Source components: ENGINE AND ENGINE COOLING.
Source record 10154566 at NHTSANHTSA communication ID: 10154554
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that a P0C28 will not cause a No Crank. also covers a Serail number for bad Aux pump module
Source components: FUEL SYSTEM, GASOLINE.
Source record 10154554 at NHTSANHTSA communication ID: 10154552
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary information document communicates a tip on the way to diagnose possible induction or exhaust air leaks using the evaporative emission cart smoke machine and ultrasonic leak detector tools.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL.
Source record 10154552 at NHTSANHTSA communication ID: 10151877
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have water or dust from the openings under the bed rails near the stake pockets. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
Source components: STRUCTURE.
Source record 10151877 at NHTSANHTSA communication ID: 10151874
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides the technician with weight capacity for the tailgate and cargo loops in the bed.
Source components: EQUIPMENT · STRUCTURE:BODY:TAILGATE.
Source record 10151874 at NHTSANHTSA communication ID: 10151839
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communicates an issues with the headliner sagging and how to reattach the velcro using Hardman Double Bubble Epoxy part number 04001.
Source components: EQUIPMENT · STRUCTURE.
Source record 10151839 at NHTSANHTSA communication ID: 10151832
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle HVAC system does not always respond to requests for changes in air delivery or temperature from the HVAC controls. The technician may find that the HVAC control module will communicate with the scan tool but the HVAC door data actual counts will read 0 counts. The dealer is directed to ensure there is 12V on circuit 300 at HVAC control module before replacing module.
Source components: ELECTRICAL SYSTEM · VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM.
Source record 10151832 at NHTSANHTSA communication ID: 10147382
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.
Source components: ENGINE AND ENGINE COOLING.
Source record 10147382 at NHTSANHTSA communication ID: 10145500
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an unwanted Stability Activation and/or a Service Stability message on the Driver Information Center. Technician may find a Diagnostic Trouble Code C0710. Technician should inspect for vehicles modifications before any in-depth diagnostics are performed.
Source components: ELECTRONIC STABILITY CONTROL (ESC).
Source record 10145500 at NHTSANHTSA communication ID: 10145486
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician with the steps to diagnosis and repair vehicles with various handling, vehicle dynamics concerns, noises from the suspension or underbody, or issues related to damaged suspension components. Before any in-depth diagnostics are performed, be aware that various issues could occur if the vehicle has been modified and inform the customer the conditions noted may not be covered under warranty. Technician will inspect for installed aftermarket suspension components. Also inspect for improperly adjusted torsion bars.
Source components: SUSPENSION.
Source record 10145486 at NHTSANHTSA communication ID: 10144467
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician with the installation of Cruise Control on a vehicle which did not come equipped with the option. Technician will need to contact the Techline Customer Support Center to determine if a calibration is available for the vehicle. If they are able to provide a calibration for the vehicle then order steering wheel with cruise control buttons, steering wheel sir coil, and steering column wiring harness.
Source components: VEHICLE SPEED CONTROL:CRUISE CONTROL.
Source record 10144467 at NHTSANHTSA communication ID: 10143789
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have raised dents or ripple appearance in the side outer panel of the cargo box around the perimeter of the wheel house opening. Technician should first access the rear of the inner wheelhouse area through the tail lamp cavity and the front of the wheelhouse from under the vehicle, and coat the inner hem of the wheel house to side outer panel with 3M Rust Fighter I. After allowing the 3M Rust Fighter I to dry then apply several coats of Nox Rust X-121B undercoating.
Source components: WHEELS.
Source record 10143789 at NHTSANHTSA communication ID: 10143773
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a random bump, chuggle, or fishbite sensation when crowding the throttle slightly with the Torque Converter Clutch on while cruising at 35-60 miles per hour. Technician should follow all published Service Information diagnostics if the concern is repaired compare to a like vehicle with the same options.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER.
Source record 10143773 at NHTSANHTSA communication ID: 10143757
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary information communicates to the dealer technician thatLight Duty Trucks equipped with automatic transmissions and 4 wheel drive may exhibit a condition of grinding/ratcheting type noise when shifting the automatic transmission into park while the transfer case is in 4 wheel drive low (4LO) range. Dealers technician's are advised this condition should be deemed a normal characteristic of 4WD low operation.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION · POWER TRAIN:TRANSFER CASE (4-WHEEL DRIVE).
Source record 10143757 at NHTSANHTSA communication ID: 10137526
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communicates to techniciansthat the Daytime Running Lamps (DRL's) or the auto headlamps will not shut off when using the daytime running lamp disable switch (Which is part of the headlamp switch), if the vehicles was built for Canada (RPO Z49). These vehicles were built with different software that doesn't allow the DRL's or Auto headlamp to be shut off. Canada law prohibits disabling daytime running lamps (DRL's) or auto headlamps.
Source components: EXTERIOR LIGHTING:HEADLIGHTS:HIGH/LOW BEAM DIMMER SWITCH.
Source record 10137526 at NHTSANHTSA communication ID: 10137202
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that the speedometer needle appears to be inaccurate. Dealer should advise the customer the specification for speedometer needle accuracy is +/- 2 MPH at any given speed when looking straight at the needle.
Source components: ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL.
Source record 10137202 at NHTSANHTSA communication ID: 10137182
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This concern may also be present while crusing at highway speeds and then an aggressive increase in throttle.This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to downshift.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE.
Source record 10137182 at NHTSANHTSA communication ID: 10137171
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician about key and theft information for Fleet Vehicles equipped with RPO 6E2 or 6E8 and converting to fleet mode. Technician will need to ensure fleet vehicles with RPO 6E2 or 6E8 should be checked to verify that the Theft Deterrent Module is in fleet mode prior to attempting to add keys.
Source components: ELECTRICAL SYSTEM:IGNITION:ANTI-THEFT:CONTROL MODULE · EQUIPMENT:ELECTRICAL:ANTI-THEFT DEVICES.
Source record 10137171 at NHTSANHTSA communication ID: 10129878
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to help diagnose and repair vehicles with a rattle, squeak, clunk, thump, or bump. If published Service Information diagnostics do not lead to a repair for the concern. Technician should inspect the opposite side shock/strut for the cause of the concern.
Source components: SUSPENSION:FRONT:SHOCK ABSORBER · SUSPENSION:REAR:SHOCK ABSORBER.
Source record 10129878 at NHTSANHTSA communication ID: 10129093
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.
Source components: EXTERIOR LIGHTING.
Source record 10129093 at NHTSANHTSA communication ID: 10129088
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn.
Source components: SERVICE BRAKES.
Source record 10129088 at NHTSANHTSA communication ID: 10129067
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a no crank concern. Technician will need to check the valve train for movement when the engine is cranked. If the valve train is not moving while the crankshaft is moving the front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the valve train is rotating during inspection, disconnect the Camshaft Position sensor and check if the engine will start. If the engine starts front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the engine does not start with the Camshaft Position sensor disconnected the follow published “Engine Cranks But Does Not Run” diagnosis in Service Information. Also perform an Engine Compression Test and Cylinder Leakage Test in Service Information documents all results. If the Service Information procedures above isolate an engine mechanical concern then removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly.
Source components: BACK OVER PREVENTION · FUEL SYSTEM, GASOLINE · POWER TRAIN:AXLE ASSEMBLY:AXLE SHAFT.
Source record 10129067 at NHTSANHTSA communication ID: 10129057
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an oil leak shortly after a cold start when extremely low ambient temperatures are present. Technician will need to clean the area of the oil leak, clean and dry the PCV hoses, and replace the oil fill cap with part number 12589430.
Source components: COMMUNICATION · FUEL SYSTEM, OTHER:DELIVERY:HOSES, LINES/PIPING, AND FITTINGS.
Source record 10129057 at NHTSANHTSA communication ID: 10126982
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
Source components: ELECTRICAL SYSTEM.
Source record 10126982 at NHTSANHTSA communication ID: 10126976
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician with the installation of Cruise Control on a vehicle which did not come equipped with the option. Technician will need to contact the Techline Customer Support Center to determine if a calibration is available for the vehicle. If they are able to provide a calibration for the vehicle then order steering wheel with cruise control buttons, steering wheel sir coil, and steering column wiring harness.
Source components: STEERING · VEHICLE SPEED CONTROL:CRUISE CONTROL.
Source record 10126976 at NHTSANHTSA communication ID: 10126975
NHTSA source summary · Original PDF not reviewed by Recallfolio
This PI was superseded to update model years and add information concerning idle surge, reduced engine power mode, and/or DTCs P0068, P0121, P1516, P2101, P2119, and/or P2176 that may be experienced on high mileage vehicles. Please discard PIP4578.
Source components: ENGINE AND ENGINE COOLING.
Source record 10126975 at NHTSANHTSA communication ID: 10126972
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.
Source components: ELECTRICAL SYSTEM.
Source record 10126972 at NHTSANHTSA communication ID: 10139167
NHTSA source summary · Original PDF not reviewed by Recallfolio
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
Source components: TIRES.
Source record 10139167 at NHTSANHTSA communication ID: 10139179
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
Source components: POWER TRAIN.
Source record 10139179 at NHTSANHTSA communication ID: 10139182
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to flush and bleed power steering system to correct a power steering noise or fluid leak concern that is caused during extremely low temperatures.
Source components: STEERING.
Source record 10139182 at NHTSANHTSA communication ID: 10139180
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure for retorque the lead springs.
Source components: SUSPENSION.
Source record 10139180 at NHTSANHTSA communication ID: 10139185
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information to diagnose batteries that have set for a long period of time and/or cold weather climates and testing those batteries.
Source components: ELECTRICAL SYSTEM.
Source record 10139185 at NHTSANHTSA communication ID: 10139181
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information on dealer responsibility for cargo carrying capacity labeling and the part numbers for the labels.
Source components: EQUIPMENT.
Source record 10139181 at NHTSANHTSA communication ID: 10190505
NHTSA source summary · Original PDF not reviewed by Recallfolio
Information on Mounting Points for Pickup Box Accessories
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · STRUCTURE:BODY.
Source record 10190505 at NHTSANHTSA communication ID: 10139088
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil consumption.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT.
Source record 10139088 at NHTSANHTSA communication ID: 10139092
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides repair information for installing a new stabilizer shaft bracket to correct a customer concern of on a clunking noise originating from the front of the vehicle that is more predominant during turns or traveling over bumps.
Source components: EQUIPMENT · STEERING.
Source record 10139092 at NHTSANHTSA communication ID: 10125131
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities. This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.
Source components: TIRES.
Source record 10125131 at NHTSANHTSA communication ID: 10125130
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have water or dust from the openings under the bed rails near the stake pockets. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
Source components: STRUCTURE.
Source record 10125130 at NHTSANHTSA communication ID: 10125126
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication a diagnostic tip if the high speed lan bus is shorted to ground, which can cause the BCM to appear off line.
Source components: ELECTRICAL SYSTEM.
Source record 10125126 at NHTSANHTSA communication ID: 10139118
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a listing of the parts availability for coax repair procedures and what is needed to complete some repairs.
Source components: EQUIPMENT.
Source record 10139118 at NHTSANHTSA communication ID: 10125106
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle's odometer appears to be inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odometer. If a hand held GPS unit is not available, the only other option is to verify the miles traveled using a surveyor's wheel or a dynamometer.
Source components: ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL.
Source record 10125106 at NHTSANHTSA communication ID: 10123285
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have a bump feel or clunk noise at a stop or on launch. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle. The bump clunk issue may be due to fuel movement in the fuel tank when not completely full. The condition is eliminated after completely filling the fuel tank.
Source components: FUEL SYSTEM, GASOLINE.
Source record 10123285 at NHTSANHTSA communication ID: 10123284
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communicates an issues with the headliner sagging and how to reattachthe velcrousing Hardman Double Bubble Epoxy part number 04001.
Source components: EQUIPMENT · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10123284 at NHTSA