2007 GMC SIERRA 1500 Manufacturer communications & TSBs.Page 5
Original record summaries, dates and identifiers for this model-year. Records 401–500 of 726, ordered newest first. Dated records on this page: May 10, 2013–Dec 18, 2014.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Dec 18, 2014Service Bulletin/Repair Instructions
PI0655A
NHTSA communication ID: 10126248
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary information bulletin provides information on how to remove stainless steel wheel nut caps with the matching depth of socket used on the wheel nut.
NHTSA source summary · Original PDF not reviewed by Recallfolio
09184B - CUSTOMER SATISFACTION (REVISED VEHICLE POPULATION, CONDITION STATEMENT AND SERVICE PROCEDURE). CERTAIN VEHICLES CURRENTLY OR PREVIOUSLY REGISTERED IN ALASKA, CONNECTICUT, DELAWARE, DISTRICT OF COLUMBIA, ILLINOIS, INDIANA, IOWA, MAINE, MARYLAND, MASSACHUSETTS, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT, WEST VIRGINIA, AND WISCONSIN MAY HAVE A CONDITION IN WHICH THE SENSING AND DIAGNOSTIC MODULE (SDM) MAY CORRODE DUE TO A SIGNIFICANT QUANTITY OF SNOW AND/OR WATER CONTAINING ROAD SALT OR OTHER CONTAMINANTS ENTERING THE VEHICLE AND SATURATING THE ACOUSTICAL PADDING BENEATH THE CARPET. THE SDM IS LOCATED UNDER THE DRIVERS SEAT BENEATH THE ACOUSTICAL PADDING. IF SUFFICIENT MOISTURE COLLECTS AND IS RETAINED IN THE PADDING, IT MAY CAUSE EXCESSIVE CORROSION UNDER THE SDM THAT COULD COMPROMISE THE MODULE SEAL AND ALLOW WATER INTRUSION THAT COULD RESULT IN SDM MALFUNCTION. IF THIS CONDITION EXISTS, THE AIRBAG READINESS LIGHT OR A SERVICE AIRBAG" MESSAGE ON THE DRIVER INFORMATION CENTER (DIC) MAY ILLUMINATE. IN RARE CASES, THE VEHICLE MAY CONTACT ONSTAR® AND THE SEAT BELT PRETENSIONERS OR FRONT AIRBAGS MAY DEPLOY. DEALERS ARE TO REMOVE THE ACOUSTICAL PAD ABOVE THE SDM, INSPECT THE SDM, AND REPLACE THE SDM, IF NECESSARY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This technical bulletin provides a procedure to add a lubricant to the rear leaf springs to correct the customers concern of a squeaking noise from the rear suspension.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides information for an available BCM calibrations that would restore bulb outages when using a second stage manufacturer
NHTSA source summary · Original PDF not reviewed by Recallfolio
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO CORRECT THE CUSTOMERS CONCERN TO REPLACE THE LEFT SIDE VALVE COVER AND ACTIVE FUEL MANAGEMENT OIL DEFLECTOR TO REDUCE OIL CONSUMPTION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
NHTSA source summary · Original PDF not reviewed by Recallfolio
BUICK/CADILLAC/CHEVROLET/GMC: DURING EXTREME LOW TEMPERATURE CONDITIONS, THE POWER STEERING MAKES NOISES OR FLUID LEAKS FROM HIGH PRESSURE HOSE, POWER STEERING PUMP OR GEAR. *PE UPDATED 9/30/13. *PE UPDATED 11/7/14. *PE
Source components: STEERING:HYDRAULIC POWER ASSIST SYSTEM · STEERING:HYDRAULIC POWER ASSIST:HOSE, PIPING, AND CONNECTIONS · STEERING:HYDRAULIC POWER ASSIST:POWER STEERING FLUID · STEERING:HYDRAULIC POWER ASSIST:PUMP.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle that has no XM audio on certain channels but XM channel info is displayed. Technician will need to contact XM and deactivate and activate the module.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin was created to aid the technician in diagnosing the difference between a shock or strut that has a fluid residule from a possible external source from a leaking shaft seal.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary bulletin provides a procedure on how to reset the power folding mirriors after they been folded manually, to fix the customers concern of the mirriors shaking or fluttering at normal driving speeds.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary bulletin provides procedures on how to reset or refresh the XM radio receiver is the customers states that they only get a few channels.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This preliminary bulletin provides a procedure to install a new design upper intake manifold with a new MAP sensor relocated to prevent ice build up and setting code P0106.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin explains a normal condition from changes in Exhaust Tone for Active Fuel Management Engines when in Three or Four Cylinder Mode
Source components: ENGINE AND ENGINE COOLING:ENGINE:GASOLINE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Slips in Reverse or Third, Delayed Reverse or Drive Engagement, DTC P0776, P2715,P2723, Harsh 2-3 Shifts (Inspect 1-2-3-4 / 3-5-R Housing and Pump Seal Rings)
NHTSA source summary · Original PDF not reviewed by Recallfolio
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.
Source components: EQUIPMENT ADAPTIVE/MOBILITY · STRUCTURE:FRAME AND MEMBERS:UNDERBODY SHIELDS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.
Source components: EQUIPMENT ADAPTIVE/MOBILITY · STRUCTURE:FRAME AND MEMBERS:UNDERBODY SHIELDS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about customers that may complain of various concerns when using Bluetooth components. Technician should use the Preliminary Information to gather information from the customer on their Bluetooth device and the concern they are having before calling General Motors Technical Assistance Center.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up. Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down, remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics. Technician may need to contact General Motors Technical Assistance Center depending on the STID, Station ID, or OnStar Customer Identifier.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a revision 11-00-90-001A to add the 2014 model year. Also, a bullet was added to the dexos 2? section with information on the 2014 Cruze diesel.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a revision for 02-08-98-002C to add the 2010-2013 model years and revise the Approved Refinish Materials booklet information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This informational bulletin provides a revision for 09-00-89-008 to add model years, update the Labor Operation Information and Transaction Submissions Procedure and general content updates.