The manufacturer’s record · Page 1 of 1
Original record summaries, dates and identifiers for this model-year. Records 1–98 of 98, ordered newest first. Dated records on this page: Jan 20, 2016–Apr 20, 2026.
Back to 2016 Ford TRANSIT CONNECT problems & recallsThis archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
NHTSA communication ID: 11031781
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customer Satisfaction Program 25N15 - Supplement #1 Certain 2015-2019 Model Year Multiple Vehicle Lines Rear View Camera Inspection For One-Time Replacement
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
Source record 11031781 at NHTSANHTSA communication ID: 11030282
NHTSA source summary · Original PDF not reviewed by Recallfolio
Advance Notice – Customer Satisfaction Program 25N17 Certain 2015-2025 Model Year Multiple Vehicle Lines Rear View Camera Replacement If Required After Dealer Evaluation
Source components: BACK OVER PREVENTION: REARVIEW SYSTEM BRAKING · BACK OVER PREVENTION: WARNINGS · LANE DEPARTURE: BLIND SPOT DETECTION · UNKNOWN OR OTHER.
Source record 11030282 at NHTSANHTSA communication ID: 11029052
NHTSA source summary · Original PDF not reviewed by Recallfolio
Ford and Lincoln vehicles equipped with wired keyless entry keypad systems and accessory wireless keyless entry keypad systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k
Source components: ELECTRICAL SYSTEM · STRUCTURE:BODY · UNKNOWN OR OTHER.
Source record 11029052 at NHTSANHTSA communication ID: 11025837
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 24-2165 to update the TSB Service Procedure. Some vehicles listed in the Model statement above may exhibit various SYNC performance related concerns including but not limited to: Display operation concerns Navigation inoperative Voice recognition concerns Phone connection issues Dropped phone connections Applink related performance Travel Link not present or showing incorrect traffic Slow system response NOTE: Ford has found some of the APIMs replaced and returned for inspection contained an outdated software level and the APIM did not require replacement. The customer concern may have been resolved by updating the APIM with latest level of software. The SYNC 3 universal thumb drive will be able to update the APIM software without the use of a scan tool and does not require the process to be monitored. Ford will be monitoring APIM replacements to confirm TSB directed software updates have been performed.
Source components: ELECTRICAL SYSTEM.
Source record 11025837 at NHTSANHTSA communication ID: 11025611
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. Pinpoint test HK in the Powertrain Control and Emissions Diagnosis (PC/ED) or in Section 303-14 of the Workshop Manual (WSM) has been updated to address this concern.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
Source record 11025611 at NHTSANHTSA communication ID: 11008948
NHTSA source summary · Original PDF not reviewed by Recallfolio
While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions. While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions.
Source components: UNKNOWN OR OTHER.
Source record 11008948 at NHTSANHTSA communication ID: 11006953
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2014-2015 Model Year Fiesta, 2014-2016 Model Year Fusion, MKZ and 2014-2016 Model Year Transit Connect Vehicles Not Covered in Safety Recall: 20S15 or 23S36 Door Latch Replacement and Inspection
Source components: UNKNOWN OR OTHER.
Source record 11006953 at NHTSANHTSA communication ID: 11001174
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 21-2175 to update the TSB Service Procedure. Some 2016 MKS, 2016-2017 Navigator, 2016-2018 F-150/Focus/C-MAX/Edge/Fiesta/MKX/Transit Connect/Mustang, 2017-2018 Continental/Fusion/MKZ, 2017-2019 Explorer, 2016-2019 Escape/MKC/Flex/MKT/Taurus/Transit/Expedition/F-Super Duty, and 2018-2019 EcoSport vehicles equipped with SYNC 3 may experience various SYNC performance related concerns. related concerns including but not limited to: Display operation concerns Navigation inoperative Voice recognition concerns Phone connection issues Dropped phone connections Applink related performance Travel Link not present or showing incorrect traffic Slow system response This may be due to the SYNC software. To correct the condition, follow the Service Procedure to update the accessory protocol interface module (APIM) software. NOTE: Ford has found some of the APIMs replaced and returned for inspection contained an outdated software level and the APIM did not require replacement. The customer concern may have been resolved by updating the APIM with latest level of software.
Source components: UNKNOWN OR OTHER.
Source record 11001174 at NHTSANHTSA communication ID: 10254138
NHTSA source summary · Original PDF not reviewed by Recallfolio
All accessory stick-on keyless entry keypads come with a wallet card containing the master code. If the accessory keypad was factory installed, this card will be placed in the glove box and should be handed to the vehicles owner during initial delivery. Unlike the integrated (wired) factory keypad, the accessory keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool. If the wallet card for an accessory keypad is lost, follow these steps to recover the code. Dealer Key Code access is granted through the Dealer Program Enrollment System (DPES); dealership management can authorize users. The authorized user must go to FMCDealer.com > Parts and Service > Parts Product Line Information > Keys/Entry Devices > Aftermarket Keyless Entry Keypad Code Access. Follow the instructions on the screen to obtain the master code for the accessory keypad.
Source components: EQUIPMENT.
Source record 10254138 at NHTSANHTSA communication ID: 10251952
NHTSA source summary · Original PDF not reviewed by Recallfolio
For 2015-2024 Ford and Lincoln vehicles equipped with turbocharged engines and customer concern of an engine oil leak, refer to Workshop Manual (WSM), Section 303-00 for oil leak inspection and testing methods. Ford has evaluated turbochargers replaced for oil leak symptoms and although oil may collect on the external surface of a turbocharger, it is extremely rare for a turbocharger assembly to be the root cause of the oil leak. Careful inspection of the turbocharger oil feed and drain tubes should be performed along with the recommended WSM procedures as needed. Warranty claims for turbocharger replacement going forward will be assessed.
Source components: ENGINE AND ENGINE COOLING.
Source record 10251952 at NHTSANHTSA communication ID: 10235153
NHTSA source summary · Original PDF not reviewed by Recallfolio
For 2000-2024 Ford and Lincoln vehicles, swapping a module from a vehicle for diagnosis purposes is likely to cause errors and is not recommended. It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.
Source components: STRUCTURE.
Source record 10235153 at NHTSANHTSA communication ID: 10218636
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2015-2016 Model Year Transit Connect Vehicles ;Windshield Glass Reseal In some of the affected vehicles, portions of the windshield may have inadequately adhered to the vehicle. Affected vehicles could experience increased wind noise, water leaks, or looseness of the windshield glass
Source components: VISIBILITY:WINDSHIELD.
Source record 10218636 at NHTSANHTSA communication ID: 10210730
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2016 Fusion, 2013-2018 C-MAX, 2014-2019 Escape, 2014-2021 Transit Connect, and 2015-2018 Edge vehicles may indicate an incorrect shifter lever position. This may be due to the bushing at the transmission end of the shifter lever cable resulting in a mismatch of cluster and selected gear position. To correct the condition, follow the Service Procedure steps to replace the bushing and on certain vehicles install the protective cap over the selector at the transmission end of the selector lever cable.
Source components: POWER TRAIN.
Source record 10210730 at NHTSANHTSA communication ID: 10209378
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 20-2047 to update the model years affected. Some 2013-2022 Transit Connect vehicles built on or after 1-Jan-2013 may exhibit a condition where either section of the second row seat is stuck or difficult to fold or unfold. This may be due to a misrouted cable or a cable that is in need of adjustment. It may be necessary to reduce the cable end fitting length. It is not necessary to install a new second row seat.
Source components: EQUIPMENT · SEATS.
Source record 10209378 at NHTSANHTSA communication ID: 10202862
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2014-2020 Transit Connect vehicles built on/or after 01-Feb-2013 may exhibit water dripping into the passenger front footwell. This may be due to an excessive gap in the heating, ventilation, and air conditioning (HVAC) case allowing water to drip from the case when the air conditioning (A/C) is operating. To correct the condition, follow the Service Procedure steps to reseal the HVAC case.
Source components: EQUIPMENT:APPLIANCE:AIR CONDITIONER.
Source record 10202862 at NHTSANHTSA communication ID: 10201050
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK12 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: ELECTRICAL SYSTEM.
Source record 10201050 at NHTSANHTSA communication ID: 10198605
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016 MKS, 2016-2017 Navigator, 2016-2018 F-150/Focus/C-MAX/Edge/Fiesta/MKX/Transit Connect/Mustang, 2017-2018 Continental/Fusion/MKZ, 2017-2019 Explorer, 2016-2019 Escape/MKC/Flex/MKT/Taurus/Transit/Expedition/F-Super Duty, and 2018-2019 EcoSport vehicles equipped with SYNC 3 may experience various SYNC performance related concerns.
Source components: ELECTRICAL SYSTEM.
Source record 10198605 at NHTSANHTSA communication ID: 10194428
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN:AUTOMATIC TRANSMISSION.
Source record 10194428 at NHTSANHTSA communication ID: 10194434
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2016 Fusion, 2013-2018 C-MAX, 2014-2019 Escape, 2014-2021 Transit Connect, and 2015-2018 Edge vehicles may indicate an incorrect shifter lever position. This may be due to the bushing at the transmission end of the shifter lever cable resulting in a mismatch of cluster and selected gear position. To correct the condition, follow the Service Procedure steps to replace the bushing and on certain vehicles install the protective cap over the selector at the transmission end of the selector lever cable.
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · POWER TRAIN.
Source record 10194434 at NHTSANHTSA communication ID: 10205001
NHTSA source summary · Original PDF not reviewed by Recallfolio
Panoramic roof panel blind inoperative, buckled and/or stuck
Source components: VISIBILITY.
Source record 10205001 at NHTSANHTSA communication ID: 10189767
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2016 Fusion, 2013-2018 C-MAX, 2013-2019 Escape, 2014-2021 Transit Connect, and 2015-2018 Edge vehicles may indicate an incorrect shifter lever position. This may be due to the bushing at the transmission end of the shifter lever cable resulting in a mismatch of cluster and selected gear position. To correct the condition, follow the Service Procedure steps to replace the bushing and install the protective cap over the selector at the transmission end of the selector lever cable.
Source components: POWER TRAIN.
Source record 10189767 at NHTSANHTSA communication ID: 10183416
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2014-2020 Transit Connect vehicles built on/or after 01-Feb-2013 may exhibit water dripping into the passenger front footwell. This may be due to an excessive gap in the heating, ventilation, and air conditioning (HVAC) case allowing water to drip from the case when the air conditioning (A/C) is operating. To correct the condition, follow the Service Procedure steps to reseal the HVAC case.
Source components: STRUCTURE · VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM.
Source record 10183416 at NHTSANHTSA communication ID: 10180428
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2009-2020 Ford and Lincoln vehicles equipped with turbochargers may exhibit an oil leak from the turbocharger oil supply or return tubes, O-rings or 6.7L pedestal gasket. Although oil may collect on the turbocharger, it is very rare for a turbocharger to leak oil. To isolate the source of the leak, refer to Workshop Manual (WSM), Section 303-00 General Information > Diagnosis and Testing > Engine > Engine Oil Leaks - Fluorescent Oil Additive Method procedure. When an oil leak is present at a turbocharger oil supply or drain tube, remove the affected oil tube and inspect for damage, and replace the O-ring seals, pedestal gasket or oil tube as required. Refer to WSM, Section 303-04. For claiming, use the affected oil tube or pedestal gasket as the causal part and applicable labor operations in Sections 6 and 9 of the Service Labor Time Standards (SLTS) Manual.
Source components: ENGINE AND ENGINE COOLING.
Source record 10180428 at NHTSANHTSA communication ID: 10179356
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2017 Expedition/Navigator, 2016-2018 Focus/C-MAX, And 2016-2018 Transit Connect vehicles may exhibit a concern where the radio will revert to an AM or FM station after the vehicle's ignition has been turned off and turned back on. To address this condition, reprogram the audio control module (ACM) using the appropriate Ford diagnostic scan tool. For claiming, use causal part 18C869 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: ELECTRICAL SYSTEM · EQUIPMENT.
Source record 10179356 at NHTSANHTSA communication ID: 10179117
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016 MKS, 2016-2017 Navigator, 2016-2018 F150/Focus/CMAX/Edge/Fiesta/MKX/ Transit Connect/Mustang, 2017-2018 Continental/Fusion/MKZ, 2017-2019 Explorer, 2016-2019 Escape/MKC/Flex/MKT/Taurus/Transit/Expedition/F-Super Duty, and 2018-2019 EcoSport vehicles equipped with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure.
Source components: ELECTRICAL SYSTEM:SOFTWARE.
Source record 10179117 at NHTSANHTSA communication ID: 10177038
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2017 Expedition/Navigator, 2016-2018 Focus/C-MAX, And 2016-2018 Transit Connect vehicles may exhibit a concern where the radio will revert to an AM or FM station after the vehicle's ignition has been turned off and turned back on. To address this condition, reprogram the audio control module (ACM) using the appropriate Ford diagnostic scan tool. For claiming, use causal part 18C869 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: EQUIPMENT.
Source record 10177038 at NHTSANHTSA communication ID: 10177042
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2020 Ford and Lincoln vehicles equipped with a SYNC 3 Touchscreen may experience the volume control unresponsive from the Front Control Interface Module (FCIM) and steering volume controls when using Apple Car Play. When the Apple device is removed, volume control is restored. This is due to a concern with the Waze Navigation App software and Apple iOS version. To correct the condition, update the Waze App software and iOS to the latest version available and reboot the customer's Apple device. Perform an ignition cycle and reconnect the Apple device via USB. Open Apple Car Play and confirm volume control is restored. Installing/Updating third party software/applications is not warrantable.
Source components: ELECTRICAL SYSTEM · EQUIPMENT.
Source record 10177042 at NHTSANHTSA communication ID: 10172969
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2019 Transit vehicles equipped with a 3.2L engine, 2018-2020 F150 vehicles equipped with a 3.0L engine, 2017-2020 Super Duty vehicles equipped with a 6.7L engine built on or after 13-May-2017 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P2002 stored in the powertrain control module (PCM). This may be due to a crack in the diesel particulate filter (DPF) substrate. To correct the condition, follow the Service Procedure steps to replace the DPF.
Source components: ENGINE AND ENGINE COOLING.
Source record 10172969 at NHTSANHTSA communication ID: 10172972
NHTSA source summary · Original PDF not reviewed by Recallfolio
SSM 48619 - Various Vehicles - Perimeter Alarm Armed And Original Vehicle Keys Cannot Be Accessed to Enter Vehicle - CAN Protection Strategy Some 2013-2016 Model Year Vehicles may exhibit a concern in which the Perimeter Alarm is active and the original keys cannot be accessed to disable the perimeter alarm. This concern would most often occur when a customer loses keys and the dealership is attempting to program new keys to the vehicle. The Workshop Manual (WSM), Section 419-01A Perimeter Anti-Theft Alarm - System Operation and Component Description has been updated to inform of the Controller Area Network (CAN) Protection Strategy. Follow the procedure outlined to prevent replacement of the Body Control Module (BCM) on CAN Protection Strategy equipped vehicles when original keys are lost and perimeter alarm is active. Refer to the WSM for further detail on the CAN Protection Strategy. Lost keys and replacement of BCM for lost keys is non-warrantable.
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
Source record 10172972 at NHTSANHTSA communication ID: 10171865
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2020 Transit Connect vehicles built on or after 1-Jan-2013 may exhibit a condition where either section of the second row seat is stuck or difficult to fold or unfold. This may be due to a misrouted cable or a cable that is in need of adjustment. It may be necessary to reduce the cable end fitting length. It is not necessary to install a new second row seat.
Source components: PARKING BRAKE:CONVENTIONAL:MECHANICAL:LINKAGE AND CABLE · SEATS · WHEELS:HUBCAP/COVER.
Source record 10171865 at NHTSANHTSA communication ID: 10169986
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2020 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: POWER TRAIN.
Source record 10169986 at NHTSANHTSA communication ID: 10168810
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2019 vehicles equipped with SYNC 3 may experience a map displayed on the left half of the SYNC screen with no other information/soft buttons present after updating to the latest version of V3.0 software. This issue occurs when the SYNC 3 system has been previously modified using an aftermarket device to display the Ford GT welcome screen/HMI Theme. To correct this issue, please contact the Technical Hotline Assistance Center to have the vehicle restored back to its original state.
Source components: ELECTRICAL SYSTEM.
Source record 10168810 at NHTSANHTSA communication ID: 10164596
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2020 vehicles equipped with an EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function. To support the proper diagnosis of this compressor, the EVDC control valve tester has been provided to each U.S. dealership (339-EVDC100). Ensure the A/C system has a full charge prior to any compressor diagnostics. To support the proper diagnosis of this compressor, the EVDC compressor tool must be used, and the results recorded in the Technician comments field with the warranty claim. This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.
Source components: EQUIPMENT:APPLIANCE:AIR CONDITIONER.
Source record 10164596 at NHTSANHTSA communication ID: 10164497
NHTSA source summary · Original PDF not reviewed by Recallfolio
For Ford and Lincoln vehicles that require positive or negative battery terminal replacement, it is not necessary to replace the complete battery cable harness (14300 and 14301) for this concern. Positive battery cable clamp BT4Z-14450-AA and negative battery cable clamp BT4Z-14450-BA are available for this type of repair. Do not cut or shorten the battery cable, instead carefully remove the affected battery cable clamp and clean the cable end as necessary to preserve wire length. Some rework may be necessary for some vehicle environments. Bend the new positive battery cable clamp as needed and crimp it to the existing battery cable. Make sure to use heat shrink tubing over the battery cable to battery cable clamp connection. Obtain the heat shrink tube locally.
Source components: ELECTRICAL SYSTEM.
Source record 10164497 at NHTSANHTSA communication ID: 10162087
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2019 Ford and Lincoln vehicles equipped with SYNC 3 not at the latest software level may exhibit Various Performance Related concerns such as Display Operation, Navigation, Voice Recognition, Phone Pairing, Applink, Travel Link, Slow System Response, etc. Check for SYNC software update under the OASIS Tab SYNC selection. If an update is available refer to WSM,Section 415-00 and update the APIM software. After Installation, complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual. Section
Source components: ELECTRICAL SYSTEM.
Source record 10162087 at NHTSANHTSA communication ID: 10160931
NHTSA source summary · Original PDF not reviewed by Recallfolio
On vehicles equipped with an automatic transmission it is imperative that the converter pilot hub be greased with Motorcraft Multi-Purpose Grease Spray XL-5-A even if grease was not applied from the factory. Also verify that the engine/transmission alignment dowel pins are present as well as the engine crankshaft dowel pin, if equipped, when installing the transmission. Failure to adequately lubricate the converter hub greatly increases the likelihood of the flexplate cracking in the future. Missing dowels may cause a misalignment issue also resulting in a premature failure. Refer to Workshop Manual (WSM), Section 307-01.
Source components: POWER TRAIN.
Source record 10160931 at NHTSANHTSA communication ID: 10160880
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2019 vehicles equipped with a EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.
Source components: EQUIPMENT:APPLIANCE:AIR CONDITIONER.
Source record 10160880 at NHTSANHTSA communication ID: 10159489
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2019 vehicles equipped with a EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:APPLIANCE:AIR CONDITIONER.
Source record 10159489 at NHTSANHTSA communication ID: 10156594
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2014-2019 Escape, 2014-2018 C-MAX, Focus, and Transit Connect vehicles not equipped with an auto start/stop system may exhibit an inability to program and/or no electrical power after installation of a service part body control module (BCM). Inspect the BCM for the presence of fuse F88. If fuse 88 is missing, install a 25 amp fuse and then re-evaluate the concern. If fuse 88 is installed in a vehicle with an auto start/stop system, the vehicle may exhibit concerns where the radio is turning off during an auto start/stop event and the instrument panel cluster (IPC) back lighting slowly goes dim during auto start/stop events.
Source components: ELECTRICAL SYSTEM.
Source record 10156594 at NHTSANHTSA communication ID: 10156887
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2017 vehicles may experience a no crank concern due to a security access key table error. When attempting to program keys or perform a parameter reset, the procedure may fail and the Integrated Diagnostic System (IDS) scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the Body Control Module (BCM) is internally faulted and requires replacement. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
Source components: ELECTRICAL SYSTEM.
Source record 10156887 at NHTSANHTSA communication ID: 10155575
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2017 vehicles may experience a no crank concern due to a security access key table error. When attempting to program keys or perform a parameter reset, the procedure may fail and the Integrated Diagnostic System (IDS) scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the Body Control Module (BCM) is internally faulted and requires replacement. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
Source components: ELECTRICAL SYSTEM.
Source record 10155575 at NHTSANHTSA communication ID: 10153969
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2012-2019 Vehicles may require repairs to the Smartlink system. Smartlink is a Ford Licensed Accessory which has a warranty provided by the accessory manufacturer. Warranty replacement parts for Smartlink that are ordered through Ford are not reimbursable through the Ford Motor Company warranty system. Please see the Warranty and Policy Manual for further information on Ford Licensed Accessories.
Source components: EQUIPMENT.
Source record 10153969 at NHTSANHTSA communication ID: 10153948
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2019 Ford and Lincoln vehicles equipped with SYNC 3 and a 6, 8 or 10 inch screen may show a pop-up message every key cycle that states 'SYNC can check for updates when connected to a WiFi network'. To remove the inconvenience of the pop-up the customer can either connect to a trusted WiFi network to complete the setup process or turn off WiFi in the WiFi settings located under the Settings menu. Adjusting the setting for the customer is not a warrantable defect.
Source components: ELECTRICAL SYSTEM.
Source record 10153948 at NHTSANHTSA communication ID: 10153944
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2014-2019 Escape, 2014-2018 C-MAX,Focus, and Transit Connect vehicles may exhibit a concern of not able to program and/or no electrical power after installation of a service part Body Control Module(BCM). Inspect the BCM for the presence of fuse F88. If the fuse is missing, install the correct size replacement fuse as outlined in the Wiring Manual and then re-evaluate the concern.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
Source record 10153944 at NHTSANHTSA communication ID: 10149770
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2018 Ford and Lincoln vehicles equipped with SYNC 3 may exhibit the Android Auto Preference menu selection is not present after an update to version 3.0 software. In prior versions of SYNC 3 software this menu was present, however in version 3.0 software the Android Auto Preference menu will only show up once an Android Phone has been initially connected to SYNC. This an operating characteristic of the Android Auto application after the SYNC 3.0 update and no repairs should be attempted.
Source components: ELECTRICAL SYSTEM.
Source record 10149770 at NHTSANHTSA communication ID: 10149759
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2018 Escape vehicles built on or before 26-Aug-2018 and 2016-2018 Focus/Transit Connect vehicles equipped with a remote start system may exhibit an immediate engine shut off with or without diagnostic trouble code (DTC) P1594 stored in the BCM after using the remote start function to start the engine. If using FordPass, the app will indicate that the vehicle started successfully, but the engine may not have started or may start and then immediately shut off. Reprogram the BCM to the latest calibration using the latest version of the appropriate Ford diagnostic scan tool. For claiming, use causal part 14A068 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: EQUIPMENT.
Source record 10149759 at NHTSANHTSA communication ID: 10144930
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2018 Ford and Lincoln vehicles equipped with SYNC 3 not at the latest software level may exhibit Various Performance Related concerns such as Display Operation, Navigation, Voice Recognition, Phone Pairing, Applink, Travel Link, Slow System Response, etc. Check for SYNC software update under the OASIS Tab SYNC selection. If an update is available refer to WSM, Section 415-00 and update the APIM software. After Installation, complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
Source components: ELECTRICAL SYSTEM.
Source record 10144930 at NHTSANHTSA communication ID: 10144181
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 18-2084 to update the Service Procedure. Some 2013-2018 Transit Connect vehicles built on 1-Jan-2013 and through 5-Jan-2018 may exhibit a condition where either section of the second row seat is stuck or difficult to fold or unfold. This may be due to a misrouted cable or a cable that is in need of adjustment. It may be necessary to reduce the cable end fitting length. It is not necessary to install a new second row seat. Follow the Service Procedure steps to correct the condition.
Source components: EQUIPMENT · SEATS:MID/REAR ASSEMBLY.
Source record 10144181 at NHTSANHTSA communication ID: 10144199
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2018 Escape/Focus/Transit Connect vehicles equipped with a remote start system may exhibit an immediate engine shut off with or without diagnostic trouble code (DTC) P1594 stored in the BCM after using the remote start function to start the engine. If using FordPass, the app will indicate that the vehicle started successfully, but the engine may not have started or may start and then immediately shut off. Reprogram the BCM using the appropriate Ford scan tool or equivalent release 110.02 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. For claiming, use causal part 14A068 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: ELECTRICAL SYSTEM · ENGINE.
Source record 10144199 at NHTSANHTSA communication ID: 10143103
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2018 Ford and Lincoln vehicles with SYNC 3 may exhibit an intermittent blue or black screen. Check for SYNC software update under the OASIS Tab SYNC selection. If update is available refer to WSM, Section 415-00 and update APIM software. After Installation Complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10143103 at NHTSANHTSA communication ID: 10143102
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various 2016-2018 vehicles with SYNC 3 may experience a touch screen that does not respond to any input. Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
Source components: ELECTRICAL SYSTEM · EQUIPMENT.
Source record 10143102 at NHTSANHTSA communication ID: 10137133
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2016 Escape and 2016 Focus, Transit and Transit Connect vehicles equipped with a front control display interface module (FCDIM) may exhibit the inability to store AM/FM presets, select AM/FM presets and/or erratic preset button operation. Reprogram the front control display interface module (FCDIM) using Integrated Diagnostic System (IDS) or Ford J2534 Diagnostic Software (FJDS) release 109.02 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. Calibration files may also be obtained at www.motorcraftservice.com. For claiming, use causal part 18C869 and applicable labor operations in Section 10 of the Service Labor Time Standards(SLTS) manual.
Source components: ELECTRICAL SYSTEM · EQUIPMENT.
Source record 10137133 at NHTSANHTSA communication ID: 10137126
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2017 Ford and Lincoln vehicles equipped with SYNC 3 version 2.2 software may exhibit a blank screen after attempting to exit Valet mode. SYNC software updates are now available under the OASIS Tab SYNC selection. If update is available, refer to WSM Section 415-00 and update APIM software. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
Source components: ELECTRICAL SYSTEM:SOFTWARE.
Source record 10137126 at NHTSANHTSA communication ID: 10137113
NHTSA source summary · Original PDF not reviewed by Recallfolio
Replacing the original equipment SYNC/Navigation system with either an aftermarket SYNC/Navigation kit or modifying original SYNC/Navigation parts to provide additional features is not recommended nor supported on any Ford, Mercury or Lincoln vehicle. Only approved Genuine Ford accessories or originally installed systems are supported and certified to function correctly with other vehicle systems. If you suspect a system has been modified, the following resources can be used to verify original equipment: Monroney Label (Window Sticker), Professional Technician Society (PTS) OASIS tab select SYNC or HVBOM. For Genuine Ford accessories use: PTS Workshop Tab select Dealer Installed Accessory or Accessory Installation.
Source components: EQUIPMENT.
Source record 10137113 at NHTSANHTSA communication ID: 10137100
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various 2016-2017 vehicles with SYNC 3 may experience a touch screen that does not respond to any input. Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
Source components: ELECTRICAL SYSTEM.
Source record 10137100 at NHTSANHTSA communication ID: 10137070
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2018 Transit Connect vehicles built on 9-Jan-2013 and through 5-Jan-2018 may exhibit a condition where the second row seat is stuck or difficult to fold or unfold. This may be due to a misrouted cable or a cable in need of adjustment. Follow the Service Procedure steps to correct the condition.
Source components: SEATS:MID/REAR ASSEMBLY.
Source record 10137070 at NHTSANHTSA communication ID: 10136597
NHTSA source summary · Original PDF not reviewed by Recallfolio
2010-2018 various vehicles equipped with SYNC or SYNC 3 may not function when attempting to find or use the Spotify app via AppLink. As of an update released on 1/15/2018 Spotify will no longer be supporting their AppLink integration. No repair attempts should be attempted to correct this concern.
Source components: EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
Source record 10136597 at NHTSANHTSA communication ID: 10140332
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various 2016-2017 vehicles with SYNC 3 may experience a touch screen that does not respond to any input. Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:SOFTWARE · EQUIPMENT · EQUIPMENT:ELECTRICAL.
Source record 10140332 at NHTSANHTSA communication ID: 10138533
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various 2016-2017 vehicles with SYNC 3 may experience a touch screen that does not respond to any input. Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
Source components: EQUIPMENT:ELECTRICAL.
Source record 10138533 at NHTSANHTSA communication ID: 10140323
NHTSA source summary · Original PDF not reviewed by Recallfolio
The Accessory (Wireless) Keyless Entry Keypad can only be used with vehicles that are factory built with Remote Keyless Entry (RKE). The master code for the Accessory (Wireless) Keyless Entry Keypad can be retrieved from FMCDealer - Parts and Service - Parts Product Line Information - Keys/Entry Devices - Aftermarket Keyless Entry Keypad Code Access. Access to this site is granted through Dealer Program Enrollment System (DPES) and Dealer Principal, General Manager or Parts and Service Director can authorize users. Once authorized the retrieval process for master code can be obtained. The master code for the Accessory Keyless Entry Keypad cannot be retrieved from the body control module(BCM) with a diagnostic tool.
Source components: EQUIPMENT · EQUIPMENT:ELECTRICAL.
Source record 10140323 at NHTSANHTSA communication ID: 10138524
NHTSA source summary · Original PDF not reviewed by Recallfolio
The Accessory (Wireless) Keyless Entry Keypad can only be used with vehicles that are factory built with Remote Keyless Entry (RKE). The master code for the Accessory (Wireless) Keyless Entry Keypad can be retrieved from FMCDealer - Parts and Service - Parts Product Line Information - Keys/Entry Devices - Aftermarket Keyless Entry Keypad Code Access. Access to this site is granted through Dealer Program Enrollment System (DPES) and Dealer Principal, General Manager or Parts and Service Director can authorize users. Once authorized the retrieval process for master code can be obtained. The master code for the Accessory Keyless Entry Keypad cannot be retrieved from the body control module(BCM) with a diagnostic tool.
Source components: EQUIPMENT:ELECTRICAL.
Source record 10138524 at NHTSANHTSA communication ID: 10127426
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2017 Ford and Lincoln vehicles equipped with SYNC 3 version 2.2 software may exhibit a blank screen after attempting to exit Valet mode. SYNC software updates are now available under the OASIS Tab SYNC selection. If update is available, refer to WSM Section 415-00 and update APIM software. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
Source components: ELECTRICAL SYSTEM · EQUIPMENT.
Source record 10127426 at NHTSANHTSA communication ID: 10127425
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some owners of 2016-2017 Ford and Lincoln vehicles equipped with SYNC 3 may experience inoperative mobile device navigation applications. Mobile device navigation via AppLink requires SYNC 3 version 2.3 or higher for Apple iOS users. Mobile device navigation via AppLink is not currently available for Android users. SYNC software updates are now available under the OASIS Tab SYNC selection. If an update is available refer to WSM, Section 415-00 and update APIM software. SYNC 3 software upgrade to support these apps is not a warrantable repair per the Warranty And Policy Manual, Section 3, Warranty Coverages SYNC.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM).
Source record 10127425 at NHTSANHTSA communication ID: 10127405
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit a no start condition with an illuminated malfunction indicator lamp (MIL) and a DTC P161A after PCM replacement. This may be due to the parameter reset procedure not being properly completed. To clear this DTC, use the Ford Integrated Diagnostic System (IDS) service tool or Ford J2534 Diagnostic Software, select - Toolbox - Body - Security - PATS Functions - Parameter Reset. Follow the on-screen instructions to complete the procedure. This procedure will transfer the existing Key ID information between the modules without the need of having 2 programmed PATS keys present. There is no need to program keys when the PCM is going to be replaced. Additional information can be found in the Workshop Manual (WSM), Section 419-01. Missing or lost keys are not warrantable.
Source components: ELECTRICAL SYSTEM · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
Source record 10127405 at NHTSANHTSA communication ID: 10119684
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some owners of 2016-2017 Ford and Lincoln vehicles equipped with SYNC 3 may experience inoperative mobile device navigation applications. Mobile device navigation via AppLink requires SYNC 3 version 2.3 or higher for Apple iOS users. Mobile device navigation via AppLink is not currently available for Android users. SYNC 3 software upgrades to support these apps are not currently available, do not attempt any repairs at this time. Engineering is investigating, monitor OASIS for updates. SYNC 3 software upgrade to support these apps is not a warrantable repair per the Warranty And Policy Manual, Section 3, Warranty Coverages SYNC.
Source components: ELECTRICAL SYSTEM:SOFTWARE.
Source record 10119684 at NHTSANHTSA communication ID: 10119678
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2017 Ford and Lincoln vehicles with SYNC 3 may exhibit an intermittent blue or black screen. Check for SYNC software update under the OASIS Tab SYNC selection. If update is available refer to WSM, Section 415-00 and update APIM software. After Installation Complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
Source components: ELECTRICAL SYSTEM:SOFTWARE.
Source record 10119678 at NHTSANHTSA communication ID: 10119686
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2015 Model Year Flex and Taurus, 2015-2016 Model Year C-MAX, and MKS, and 2016 Model Year Edge, Fusion, MKZ, and Transit Connect Vehicles - Electronic Throttle Body Replacement
Source components: EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10119686 at NHTSANHTSA communication ID: 10119669
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2017 Ford and Lincoln vehicles equipped with SYNC 3 version 2.2 software may exhibit a blank screen after attempting to exit Valet mode. To recover the screen, perform a complete ignition cycle (key off, open and close the driver's door then wait 5 minutes). The SYNC software version of the vehicle can be confirmed via OASIS. Do not attempt any repairs at this time. Engineering is investigating; Monitor OASIS for updates.
Source components: ELECTRICAL SYSTEM:SOFTWARE.
Source record 10119669 at NHTSANHTSA communication ID: 10109015
NHTSA source summary · Original PDF not reviewed by Recallfolio
For 2014-2017 Transit Connect Vehicles with a Taxi Conversion there is a 12-Pin block connector available for connecting the taxi spot lights to the main body harness. Service Part Number GU2Z-14S411-JA.
Source components: ELECTRICAL SYSTEM · EXTERIOR LIGHTING.
Source record 10109015 at NHTSANHTSA communication ID: 10100508
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2016-2017 FORD OR LINCOLN VEHICLES EQUIPPED WITH SYNC 3 MAY EXHIBIT A BLANK SCREEN OR OTHER VARIOUS SYNC SYMPTOMS ONLY WHEN THE VEHICLE IS IN TRANSPORT MODE. THIS IS CONSIDERED NORMAL DUE TO THE POWER SAVING FEATURES ENABLED WHILE IN TRANSPORT MODE. IT IS BENEFICIAL FOR BATTERY LIFE TO KEEP THE VEHICLE IN TRANSPORT MODE UNTIL THE VEHICLE IS PREPPED FOR SALE. TO PREVENT A SYNC SYSTEM LOCKUP DURING TRANSPORT MODE DEACTIVATION, FOLLOW THE WORKSHOP MANUAL (WSM) PROCEDURE EXACTLY ALLOWING TIME FOR THE SYNC SYSTEM TO COMPLETE ITS TASKS SUCH AS FULLY BOOTING UP OR POWERING DOWN AND SHUTTING OFF BEFORE MOVING TO THE NEXT STEP OF THE PROCEDURE. IF THE VEHICLE EXHIBITS A BLANK SCREEN OR SYNC SYMPTOMS AFTER TRANSPORT MODE DEACTIVATION, REFER TO WSM, SECTION 415-00 FOR NORMAL DIAGNOSIS. THE SYNC VERSION CAN BE CONFIRMED VIA OASIS.
Source components: ELECTRICAL SYSTEM:12V/24V/48V BATTERY.
Source record 10100508 at NHTSANHTSA communication ID: 10100525
NHTSA source summary · Original PDF not reviewed by Recallfolio
CERTAIN 2016-2017 MODEL YEAR TRANSIT CONNECT - FLOOR MATS INCOMPATIBLE WITH VINYL FLOOR.
Source components: EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10100525 at NHTSANHTSA communication ID: 10099452
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2013-2017 TRANSIT CONNECT VEHICLES BUILT ON OR BEFORE 13-JAN-2017 MAY REQUIRE REPLACEMENT OF THE PANORAMIC ROOF SHADE. WHEN INSTALLING THE NEW ROOF SHADE THE WIRE HARNESS CONNECTOR FOR THE ROOF SHADE MODULE MAY NEED TO BE EXTENDED IN ORDER TO REACH THE NEW MODULE. FOLLOW THE RECOMMENDED SPLICING METHOD FOR EXTENDING THE HARNESS IN THE ON-LINE WIRING DIAGRAMS SECTION 5-1, CONNECTOR REPAIR PROCEDURES.
Source components: EQUIPMENT.
Source record 10099452 at NHTSANHTSA communication ID: 10095624
NHTSA source summary · Original PDF not reviewed by Recallfolio
MULTIPLE 2014-2016 VEHICLES EQUIPPED WITH 6F35 TRANSMISSION AND BUILT ON 1-JAN-2014 AND THROUGH 31-DEC-2015 MAY EXHIBIT HARSH REVERSE ENGAGEMENT AND HARSH/DELAYED 3RD AND 5TH GEAR UP/DOWN SHIFTS WITH NO DTCS PRESENT. THIS MAY BE DUE TO A MECHANICALLY BINDING SHIFT SOLENOID B (SSB). VERIFY HARSH REVERSE AND 3RD AND 5TH GEAR SHIFT EVENTS ARE PRESENT. USING IDS, IDENTIFY THE BAND NUMBER OF SSB FOR USE WHEN ORDERING PARTS. REMOVE THE MAIN CONTROL. DISASSEMBLE AND THOROUGHLY CLEAN THE VALVE BODY AND SOLENOID BODY TO REMOVE ANY CONTAMINANTS. REPLACE SSB, REFER TO WORKSHOP MANUAL (WSM) SECTION 307-01. USING IDS, CLEAR TRANSMISSION ADAPTIVE TABLES. FOR CLAIMING, USE CAUSAL PART 7G383 AND APPLICABLE LABOR OPERATIONS IN SECTION 7 OF THE SERVICE LABOR TIME STANDARDS (SLTS) MANUAL.
Source components: POWER TRAIN:MANUAL TRANSMISSION:SHIFT PATTERN INDICATOR.
Source record 10095624 at NHTSANHTSA communication ID: 10095184
NHTSA source summary · Original PDF not reviewed by Recallfolio
REPLACING THE ORIGINAL EQUIPMENT SYNC/NAVIGATION SYSTEM WITH EITHER AN AFTERMARKET SYNC/NAVIGATION KIT OR MODIFYING ORIGINAL SYNC/NAVIGATION PARTS TO PROVIDE ADDITIONAL FEATURES IS NOT RECOMMENDED NOR SUPPORTED ON ANY FORD, MERCURY OR LINCOLN VEHICLE. ONLY APPROVED GENUINE FORD ACCESSORIES OR ORIGINALLY INSTALLED SYSTEMS ARE SUPPORTED AND CERTIFIED TO FUNCTION CORRECTLY WITH OTHER VEHICLE SYSTEMS. IF YOU SUSPECT A SYSTEM HAS BEEN MODIFIED, THE FOLLOWING RESOURCES CAN BE USED TO VERIFY ORIGINAL EQUIPMENT: MONRONEY LABEL (WINDOW STICKER), PROFESSIONAL TECHNICIAN SOCIETY (PTS) OASIS TAB SELECT SYNC OR HVBOM. FOR GENUINE FORD ACCESSORIES USE: PTS WORKSHOP TAB SELECT DEALER INSTALLED ACCESSORY OR ACCESSORY INSTALLATION.
Source components: EQUIPMENT.
Source record 10095184 at NHTSANHTSA communication ID: 10095175
NHTSA source summary · Original PDF not reviewed by Recallfolio
2013-2016 FIESTA, ESCAPE, TRANSIT CONNECT AND 2013 FUSION VEHICLES WITH A 1.6L GASOLINE TURBOCHARGED DIRECT INJECTION (GTDI) ENGINE MAY EXHIBIT AN ENGINE OIL LEVEL READING THAT IS UP TO 8 MM ABOVE THE MAXIMUM MARK ON THE ENGINE OIL DIPSTICK WHEN THE ENGINE IS FILLED WITH THE CORRECT AMOUNT OF OIL. THIS IS A NORMAL CHARACTERISTIC OF THIS ENGINE. DO NOT LOWER THE OIL LEVEL TO THE MAXIMUM MARK ON THE ENGINE OIL DIPSTICK IF THE ENGINE CONTAINS THE CORRECT AMOUNT OF OIL. ADDING OIL IS NOT REQUIRED IF THE LEVEL IS ABOVE THE MINIMUM MARK ON THE ENGINE OIL DIPSTICK. REFER TO THE OWNERS MANUAL FOR PROPER ENGINE OIL CAPACITY.
Source components: ENGINE · EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10095175 at NHTSANHTSA communication ID: 10095170
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2014-2017 TRANSIT CONNECT VEHICLES, MAY EXHIBIT A CONDITION THAT CAUSES THE BATTERY TO DISCHARGE. IF NORMAL BATTERY DRAIN DIAGNOSIS LEADS TO NO ISSUES, IT MAY BE CAUSED BY THE APPROACH LIGHTS ILLUMINATING EVERY TIME THE BODY CONTROL MODULE (BCM) RECEIVES A LOCK/UNLOCK SIGNAL OR OPENING ANY DOOR. IF THE DOOR REMAINS OPEN, THE LIGHTS WILL REMAIN ILLUMINATED FOR UP TO 10 MINUTES. IF THE VEHICLE WAS BUILT ON OR BEFORE 11-DEC-2016, REPROGRAM THE BCM TO THE LATEST CALIBRATION USING IDS RELEASE 103.05 AND HIGHER. CALIBRATION FILES MAY ALSO BE OBTAINED AT WWW.MOTORCRAFT.COM. FOR ALL VEHICLES, ACCESS THE BCM CONFIGURATION PARAMETERS. SELECT MODULE PROGRAMMING, PROGRAMMABLE PARAMETERS, PERSONALITY, APPROACH LIGHT. CHOOSE DISABLED AND FOLLOW THE SCREEN PROMPTS TO COMPLETION. USE CAUSAL PART 14A068 AND APPLICABLE LABOR OPERATIONS IN SECTION 10 OF THE SLTS MANUAL.
Source components: ELECTRICAL SYSTEM:12V/24V/48V BATTERY.
Source record 10095170 at NHTSANHTSA communication ID: 10095154
NHTSA source summary · Original PDF not reviewed by Recallfolio
TO HELP DIFFERENTIATE ENGINE OIL LEAKS FROM OTHER POSSIBLE SOURCES, A NEW WHITE-COLORED FLUORESCENT ENGINE OIL DYE IS AVAILABLE. WORKSHOP MANUAL (WSM), SECTION 303-00 HAS BEEN REVISED TO REFERENCE THE NEW WHITE-COLORED DYE. THE NEW WHITE FLUORESCENT DYE PROVIDES A DISTINCT WHITE GLOW TO IDENTIFY ENGINE OIL LEAKS. THE NEW WHITE FLUORESCENT DYE REQUIRES A PURE UV DIAGNOSTIC INSPECTION LAMP. THE WHITE-COLORED FLUORESCENT DYE AND PURE UV LAMP ARE NOW IN THE ROTUNDA CATALOG. DYE AND LAMP PART NUMBERS. GASOLINE ONLY DYE: 1 OUNCE BOTTLE 164-TP-33200601. DIESEL ONLY DYE: 8 OUNCE BOTTLE: 164-TP-3320-0008. PURE UV DIAGNOSTIC INSPECTION LAMP 164-TP8695 OR 164-R3748.
Source components: ENGINE.
Source record 10095154 at NHTSANHTSA communication ID: 10095152
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2014-2017 TRANSIT CONNECT VEHICLES ARE EQUIPPED WITH CORNERING LAMPS. THE CORNERING LAMPS SHARE THE SAME BULB AS THE FOG LAMPS AND ILLUMINATE WHEN THE VEHICLE SPEED IS LESS THAN 25 MPH AND THE BODY CONTROL MODULE (BCM) RECEIVES A REQUEST FOR A TURN SIGNAL OR THE STEERING WHEEL IS TURNED GREATER THAN 35 DEGREES FROM CENTER. BEFORE DIAGNOSING A RIGHT OR LEFT FOG LAMP THAT MAY SEEM TO BE STUCK ON, TURN THE STEERING WHEEL BACK TO CENTER. IF THE LAMP GOES OFF, THE VEHICLE IS EQUIPPED WITH CORNERING LAMPS AND ARE WORKING AS DESIGNED. REFER TO THE WORKSHOP MANUAL SECTION 417-01 EXTERIOR LIGHTING.
Source components: EXTERIOR LIGHTING:FOG LIGHTS.
Source record 10095152 at NHTSANHTSA communication ID: 10094582
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2014-2016 TRANSIT CONNECT VEHICLES EQUIPPED WITH THE 2.5L ENGINE MAY EXHIBIT A CONSTANT OR INTERMITTENT ILLUMINATED MIL WITH VARIOUS DRIVABILITY ISSUES AND ONE OR MORE OF THE FOLLOWING DTCS: P0010, P0103, P0104, P0122, P0131, P0135, P0137, P0141, P0201-P0204, P0217, P0222, P0223, P025A, P0300, P0301-P0304, P0316, P0351-P0354, P0400, P0403, P0443, P1285, P1289, P128A, P1299, P2101, P2107, P2111, P2112, P2122, P2127 AND/OR U0109. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.
Source components: ENGINE.
Source record 10094582 at NHTSANHTSA communication ID: 10094580
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2014-2017 TRANSIT CONNECT VEHICLES MAY EXHIBIT AN INOPERATIVE LOW BEAM HEADLAMP BULB(S) DUE TO HEAT DAMAGE AT THE BULB CONNECTOR. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.
Source components: EQUIPMENT.
Source record 10094580 at NHTSANHTSA communication ID: 10091133
NHTSA source summary · Original PDF not reviewed by Recallfolio
ON 2016 TRANSIT CONNECT VEHICLES EQUIPPED WITH A 2.5L FLEX FUEL VEHICLE (FFV) ENGINE THE PARTS CATALOG IS BEING UPDATED TO CORRECTLY IDENTIFY THE FUEL FILLER NECK. THE 2.5L ENGINES CAN HAVE AN FFV OR NON-FFV FUEL FILLER NECK. IF THE ORIGINAL FUEL FILLER NECK IS BLACK (NON-FFV) ORDER DV6Z-9034-A, DV6Z-9034-C OR DV6Z-9034-K. IF THE ORIGINAL FUEL FILLER NECK IS YELLOW (FFV) ORDER PART NUMBER FV6Z-9034-G. THE PARTS CATALOG IS IN THE PROCESS OF BEING UPDATED.
Source components: ENGINE.
Source record 10091133 at NHTSANHTSA communication ID: 10090663
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2014-2017 TRANSIT CONNECT VEHICLES MAY EXHIBIT LOW BEAM HEADLAMP BULB BURN OUT, IN WHICH THE BULB CONNECTOR IS ALSO DAMAGED. THIS CONCERN IS UNDER INVESTIGATION. DO NOT REPLACE THE HEADLAMP ASSEMBLY. TO SERVICE, USE PIGTAIL KIT 8U2Z-14S411-GA. DO NOT SHORTEN THE WIRES ON THE PIGTAIL KIT, SO THEY CAN ACT AS A HEAT SINK TO DRAW HEAT AWAY FROM THE BULB. A NEW PART AND PROCEDURE IS BEING DEVELOPED. MONITOR OASIS FOR UPDATES.
Source components: EXTERIOR LIGHTING.
Source record 10090663 at NHTSANHTSA communication ID: 10090505
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2015-2016 F-150, C-MAX, EDGE, MKS, TAURUS, AND FLEX AND 2016 EXPEDITION, EXPLORER, ESCAPE, FUSION, MUSTANG, MKZ, MKX, NAVIGATOR, TRANSIT AND TRANSIT CONNECT VEHICLES EQUIPPED WITH A 2.0L, 2.5L, 3.5L OR 3.7L GASOLINE ENGINE AND BUILT ON OR BEFORE 31-MAY-2016 MAY EXHIBIT AN INTERMITTENT LOSS OF POWER AND/OR AN ILLUMINATED POWERTRAIN MALFUNCTION (WRENCH) LAMP WITH DIAGNOSTIC TROUBLE CODES (DTCS) P2111, P2112 AND/OR P2119 STORED IN POWERTRAIN CONTROL MODULE (PCM) MEMORY. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.
Source components: ENGINE.
Source record 10090505 at NHTSANHTSA communication ID: 10109079
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may have a concern where the safety belt retractor webbing does not extract from the stowed position or exhibits excessive pressure on the occupant during use. This may be due to a normal condition which happens when the seatbelt retracts at a high rate of speed. The Workshop Manual, Section 501-20A General Procedures has been updated with a locked seatbelt retractor releasing procedure.
Source components: SEAT BELTS · SEAT BELTS:FRONT:RETRACTOR.
Source record 10109079 at NHTSANHTSA communication ID: 10109070
NHTSA source summary · Original PDF not reviewed by Recallfolio
The Powertrain Control/Emissions Diagnosis (PC/ED) manual has been revised for diagnosing electronic throttle bodies (ETBs). The ETC_ACT and ETC_DSD PIDs should not used to diagnose possible ETB concerns. The IDS has a limited refresh rate when reading these PIDs and cannot display quickly enough to validate a concern. The PCM automatically monitors these inputs more accurately and will set diagnostic trouble codes (DTCs) when appropriate. Using these PIDs for diagnostics will lead to inaccurate results and improper ETB replacements. If a concern is intermittent and no DTCs are present, refer to historical DTCs and the PC/ED, Section 3 No DTCs Present Index chart for further information.
Source components: ENGINE · ENGINE AND ENGINE COOLING · ENGINE AND ENGINE COOLING:COOLING SYSTEM · ENGINE AND ENGINE COOLING:COOLING SYSTEM:FAN · ENGINE AND ENGINE COOLING:COOLING SYSTEM:HOSES/LINES/PIPING/FITTINGS · ENGINE AND ENGINE COOLING:COOLING SYSTEM:RADIATOR ASSEMBLY · ENGINE AND ENGINE COOLING:ENGINE · ENGINE AND ENGINE COOLING:ENGINE:DIESEL · ENGINE AND ENGINE COOLING:ENGINE:GASOLINE · ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:BELTS AND ASSOCIATED PULLEYS · ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER · ENGINE AND ENGINE COOLING:ENGINE:OTHER FUEL TYPES:TURBO/SUPERCHARGER · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV) · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:GAS RECIRCULATION VALVE (EGR VALVE) · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE.
Source record 10109070 at NHTSANHTSA communication ID: 10109044
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2017 Transit vehicles equipped with a 3.5L GTDI engine and built on or before 13-Sep-2016 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P130D and no related performance concern. An occasional spark knock noise may be noticed with this condition. Follow the Service Procedure steps to correct the condition.
Source components: ELECTRICAL SYSTEM · ENGINE.
Source record 10109044 at NHTSANHTSA communication ID: 10109042
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2016 Transit Connect vehicles may exhibit a water leak into the passenger side footwell. Follow the Service Procedure steps to correct the condition.
Source components: EQUIPMENT · STRUCTURE:BODY:DOOR.
Source record 10109042 at NHTSANHTSA communication ID: 10079007
NHTSA source summary · Original PDF not reviewed by Recallfolio
HOLE OR TEAR IN RUBBER FLOOR COVERING - DRIVER'S SIDE
Source components: EQUIPMENT.
Source record 10079007 at NHTSANHTSA communication ID: 10078977
NHTSA source summary · Original PDF not reviewed by Recallfolio
REPLACEMENT SEAT BACK REMAINS FOLDED IF NOT INSTALLED, NORMAL OPERATION
Source components: SEATS.
Source record 10078977 at NHTSANHTSA communication ID: 10183749
NHTSA source summary · Original PDF not reviewed by Recallfolio
In some of the affected vehicles, the front control/display interface module (FCDIM) may have been unintentionally programmed for the European market instead of the North American market
Source components: ELECTRICAL SYSTEM.
Source record 10183749 at NHTSANHTSA communication ID: 10076522
NHTSA source summary · Original PDF not reviewed by Recallfolio
Radio and Front Display Anomalies REASON FOR THIS PROGRAM In some of the affected vehicles, the front control/display interface module (FCDIM) may have been unintentionally programmed for the European market instead of the North American market, resulting in the following symptoms: The radio band cannot be changed from FM1 (the tuner may change to AM but the display continues to show FM1). Satellite radio cannot be accessed. The Europe-specific park distance control feature is enabled, and displays on the FCDIM when the forward vehicle speed drops below 6 mph (10 kph).
Source components: EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
Source record 10076522 at NHTSANHTSA communication ID: 10076301
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2015-2016 Model Year Transit Connect Vehicles Radio and Front Display Anomalies In some of the affected vehicles, the front control/display interface module (FCDIM) may have been unintentionally programmed for the European market instead of the North American market, resulting in the following symptoms: h The radio band cannot be changed from FM1 (the tuner may change to AM but the display continues to show FM1). h Satellite radio cannot be accessed. h The Europe-specific park distance control feature is enabled, and displays on the FCDIM when the forward vehicle speed drops below 6 mph (10 kph). Additionally, on some of the affected vehicles that are equipped with the rear camera zoom feature, the body control module (BCM) may be misconfigured, causing the rear camera zoom feature to be inoperative
Source components: EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
Source record 10076301 at NHTSANHTSA communication ID: 10205019
NHTSA source summary · Original PDF not reviewed by Recallfolio
2.5L - Air conditioning (A/C) inoperative fand/or message center ambient air temperature display inaccurate - DTCS P0073, P0074, and/or U0422
Source components: EQUIPMENT:APPLIANCE:AIR CONDITIONER · VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM.
Source record 10205019 at NHTSANHTSA communication ID: 10075284
NHTSA source summary · Original PDF not reviewed by Recallfolio
2.5L - AIR CONDITIONING (A/C) INOPERATIVE AND/OR MESSAGE CENTER AMBIENT AIR TEMPERATURE DISPLAY INACCURATE - DTCS P0073, P0074 AND/OR U0422 ISSUE Some 2014-2016 Transit Connect vehicles equipped with 2.5L engine may exhibit an intermittent condition in which the ambient air temperature (AAT) display in the instrument panel cluster (IPC) is inaccurate and/or the A/C is inoperative. The inoperative A/C may be caused by the AAT reading below -1.1 °C (30 °F) the actual ambient temperature is above -1.1 °C (30 °F) with diagnostic trouble codes (DTCs) P0073, P0074 and/or U0422.
Source components: EQUIPMENT:APPLIANCE:AIR CONDITIONER.
Source record 10075284 at NHTSANHTSA communication ID: 10075276
NHTSA source summary · Original PDF not reviewed by Recallfolio
AM INOPERATIVE AND/OR SATELLITE RADIO DISPLAY SHOWS - NOT EQUIPPED - BUILT ON 10/26/2015 AND THROUGH 1/20/2016 Some 2016 Transit Connect vehicles built on 10/26/15 and through 1/20/2016, equipped with SYNC and a 107 mm (4.2-inch) screen may exhibit a concern when selecting the AM radio function, the FM radio function appears and/or the satellite equipped radio display shows - not equipped, when selected. SERVICE PROCEDURE 1. When selecting the AM Radio function, does the radio change to FM and/or when selecting the satellite function, does the display show as - not equipped? a. Yes - proceed to Step 2. b. No - this article does not apply. Refer to Workshop Manual (WSM), Section 415-00 for normal diagnosis. 2. Reprogram the front control/display information module (FCDIM) to the latest calibration using Integrated Diagnostic System (IDS) release 99.04 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. Calibration files may also be obtained at www.motorcraftservice.com.
Source components: EQUIPMENT:ELECTRICAL.
Source record 10075276 at NHTSANHTSA communication ID: 10205003
NHTSA source summary · Original PDF not reviewed by Recallfolio
3.5L GKTDI Illuminated MIL - dDTC p0011, p0015, p0016, p0017, p0018, p0019, p0021 And.or p0025 - Under 3200 KM (2000Miles)
Source components: ELECTRICAL SYSTEM.
Source record 10205003 at NHTSANHTSA communication ID: 10075266
NHTSA source summary · Original PDF not reviewed by Recallfolio
PANORAMIC ROOF PANEL BLIND INOPERATIVE, BUCKLED AND/OR STUCK. Some 2014-2016 Transit Connect vehicles may exhibit a condition in which the panoramic roof panel blind moves and stops 150 mm (6 inches) from the full open position or does not move at all. The blind may be buckled and/or stuck. 1. Is the panoramic roof panel blind inoperative, buckled and/or stuck? a. Yes - proceed to Step 2. b. No - this article does not apply. Refer to Workshop Manual (WSM), Section 501-05 for normal diagnosis. 2. Replace the panoramic roof panel blind assembly. Refer to WSM, Section 501-05.
Source components: ELECTRICAL SYSTEM · STRUCTURE:BODY:ROOF AND PILLARS.
Source record 10075266 at NHTSANHTSA communication ID: 10205011
NHTSA source summary · Original PDF not reviewed by Recallfolio
AM inoperative and/or satellite radio display shows - not equipped built on 10/26/2015 and through 01/20/2016
Source components: EQUIPMENT · EQUIPMENT:APPLIANCE:TV/RADIO/SPEAKERS.
Source record 10205011 at NHTSA