2018 Ford FUSION Manufacturer communications & TSBs.Page 2
Original record summaries, dates and identifiers for this model-year. Records 101–160 of 160, ordered newest first. Dated records on this page: Oct 4, 2017–Mar 7, 2019.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Mar 7, 2019Service Bulletin/Repair Instructions
SSM 47849
NHTSA communication ID: 10156569
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2014-2019 Fusion and 2017-2019 Escape equipped with 1.5L Ecoboost engine may exhibit coolant consumption and white smoke concern. Follow the Cooling System Pressure Test procedure in WSM, Section 303-03, pressurize the cooling system to 138kPa(20 psi0 and hold for 5 hours. If cooling system pressure drops 27.57kPa(4psi) after 5 hours and internal engine coolant loss is confirmed, further investigation of the engine block surface to head gasket interface is required. Carefully inspect engine block cylinders and cylinder bore bridges for erosion, pitting, and flatness. If defects with the cylinder block surface are identified, follow WSM, Section 303-01A procedures for repairs. Complete cost cap as needed to determine the most cost effective repair. Ford has found that all returned cylinder heads pass inspection and may have been reused.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2017 vehicles may experience a no crank concern due to a security access key table error. When attempting to program keys or perform a parameter reset, the procedure may fail and the Integrated Diagnostic System (IDS) scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the Body Control Module (BCM) is internally faulted and requires replacement. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2017 vehicles may experience a no crank concern due to a security access key table error. When attempting to program keys or perform a parameter reset, the procedure may fail and the Integrated Diagnostic System (IDS) scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the Body Control Module (BCM) is internally faulted and requires replacement. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2019 Explorer, 2016-2018 MKX, 2019 Edge/Nautilus, 2017-2019 Fusion/MKZ, and 2018-2019 F-150/Mustang/Expedition/Navigator vehicles equipped with climate controlled seats may exhibit a buzzing noise from the front seats, front seats too warm, and/or inoperative climate controlled front seats. DTCs B14BA:13, B1154:4B, and/or B14B9:13 may also be present. This may be due to loose terminal pin fit on the driver seat module (DSM) connector C341D (16 pin). If a loose terminal pin fit condition is found during normal diagnostics per Workshop Manual (WSM), Section 501-10, a new service pigtail connector (part number 3U2Z-14S411-BRAB) is available. Refer to Wiring Diagram, Cell 119 to make sure C341D is a 16 pin connector and not a 20 pin connector. Refer to Wiring Diagram, Cell 5 for the recommended splicing procedures.
Source components: ELECTRICAL SYSTEM · SEATS · SEATS:FRONT ASSEMBLY:SEAT HEATER/COOLER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2019 Explorer, 2016-2018 MKX, 2019 Edge/Nautilus, 2017-2019 Fusion/MKZ, and 2018-2019 F-150/Mustang/Expedition/Navigator vehicles equipped with climate controlled seats may exhibit a buzzing noise from the front seats, front seats too warm, and/or inoperative climate controlled front seats. DTCs B14BA:13, B1154:4B, and/or B14B9:13 may also be present. This may be due to loose terminal pin fit on the driver seat module (DSM) connector C341D (16 pin). If a loose terminal pin fit condition is found during normal diagnostics per Workshop Manual (WSM), Section 501-10, a new service pigtail connector (part number 3U2Z-14S411-BRAB) is available. Refer to Wiring Diagram, Cell 119 to make sure C341D is a 16 pin connector and not a 20 pin connector. Refer to Wiring Diagram, Cell 5 for the recommended splicing procedures.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2000 and newer Ford, Lincoln and Mercury vehicles equipped with aluminum body panels may exhibit corrosion concerns appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended. Follow the Service Procedure steps to correct the condition
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2000 and newer Ford, Lincoln and Mercury vehicles equipped with aluminum body panels may exhibit corrosion concerns appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended. Follow the Service Procedure steps to correct the condition
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2019 F150/Edge, 2016-2018 MKX, 2019 Nautilus and 2017-2019 Fusion/Continental vehicles equipped with a 2.7L engine may exhibit a malfunction indicator lamp (MIL) and/or wrench lamp with diagnostic trouble codes (DTCs) P0116, P0117, P0118, P0119, P0217, P0330, P1026, and/or P130D. This may be due to a engine coolant temperature (ECT) sensor connector which is not fully seated or damaged wiring between connectors C1064 and C1047 for F150 and C1016 and C1168 for Edge/MKX/Nautilus/Fusion/Continental vehicles. ECT sensors should not be replaced if damaged wiring is found at or near these connectors. For claiming, use causal part 12A699 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING:COOLING SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2019 Fusion/MKZ and 2013-2018 C-Max vehicles with 2.0L HEV/PHEV engine may exhibit multiple drivability or electrical concerns with one or more diagnostic trouble codes, being the most common P26C3, P26CA, P26D0, P2800, P2802, U019F and U0284. On Fusion/MKZ inspect connectors C146, C1651, C1812, C168C, C1717 and C134 for signs of water entry or corrosion. On C-Max, inspect connectors C134, C140, C144, C1651, C1717 and C1812 and service as necessary. NOTE: Connector C1717 is only equipped on PHEVs for both Fusion and C-Max.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2019 F150/Edge, 2016-2018 MKX, 2019 Nautilus and 2017-2019 Fusion/Continental vehicles equipped with a 2.7L engine may exhibit a malfunction indicator lamp (MIL) and/or wrench lamp with diagnostic trouble codes (DTCs) P0116, P0117, P0118, P0119, P0217, P0330, P1026, and/or P130D. This may be due to a engine coolant temperature (ECT) sensor connector which is not fully seated or damaged wiring between connectors C1064 and C1047 for F150 and C1016 and C1168 for Edge/MKX/Nautilus/Fusion/Continental vehicles. ECT sensors should not be replaced if damaged wiring is found at or near these connectors. For claiming, use causal part 12A699 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2019 Fusion/MKZ and 2013-2018 C-Max vehicles with 2.0L HEV/PHEV engine may exhibit multiple drivability or electrical concerns with one or more diagnostic trouble codes, being the most common P26C3, P26CA, P26D0, P2800, P2802, U019F and U0284. On Fusion/MKZ inspect connectors C146, C1651, C1812, C168C, C1717 and C134 for signs of water entry or corrosion. On C-Max, inspect connectors C134, C140, C144, C1651, C1717 and C1812 and service as necessary. NOTE: Connector C1717 is only equipped on PHEVs for both Fusion and C-Max.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some all-wheel drive (AWD) 2013-2018 Escape vehicles equipped with 1.5L/1.6L/2.0L EcoBoost/Fusion vehicles equipped with 2.0L/2.7L EcoBoost/MKZ vehicles equipped with 2.0L EcoBoost, 2017-18 MKZ vehicles equipped with 3.0L EcoBoost, 2015-2018 MKC vehicles equipped with 2.0L/2.3L EcoBoost/Edge vehicles equipped with 2.0L/2.7L EcoBoost, 2016-2018 MKX vehicles equipped with 2.0L and 2.7L EcoBoost/Explorer vehicles equipped with 2.3L EcoBoost/Focus RS equipped with 2.3L EcoBoost, and 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost may exhibit a dark black fluid leak from the right side transfer case intermediate shaft seal. Follow the Service Procedure steps to correct the condition.
Source components: POWER TRAIN · POWER TRAIN:AXLE ASSEMBLY:AXLE SHAFT:SEAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some all-wheel drive (AWD) 2013-2018 Escape vehicles equipped with 1.5L/1.6L/2.0L EcoBoost/Fusion vehicles equipped with 2.0L/2.7L EcoBoost/MKZ vehicles equipped with 2.0L EcoBoost, 2017-18 MKZ vehicles equipped with 3.0L EcoBoost, 2015-2018 MKC vehicles equipped with 2.0L/2.3L EcoBoost/Edge vehicles equipped with 2.0L/2.7L EcoBoost, 2016-2018 MKX vehicles equipped with 2.0L and 2.7L EcoBoost/Explorer vehicles equipped with 2.3L EcoBoost/Focus RS equipped with 2.3L EcoBoost, and 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost may exhibit a dark black fluid leak from the right side transfer case intermediate shaft seal. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2012-2019 Vehicles may require repairs to the Smartlink system. Smartlink is a Ford Licensed Accessory which has a warranty provided by the accessory manufacturer. Warranty replacement parts for Smartlink that are ordered through Ford are not reimbursable through the Ford Motor Company warranty system. Please see the Warranty and Policy Manual for further information on Ford Licensed Accessories.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2019 Ford Fusion vehicles, the engine beauty cover was deleted as a running change. If during PDI a unit is reported as received without engine beauty cover from factory, the unit was built correctly. Any repair or the addition of this part would not be considered warrantable.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2019 Ford and Lincoln vehicles equipped with SYNC 3 and a 6, 8 or 10 inch screen may show a pop-up message every key cycle that states 'SYNC can check for updates when connected to a WiFi network'. To remove the inconvenience of the pop-up the customer can either connect to a trusted WiFi network to complete the setup process or turn off WiFi in the WiFi settings located under the Settings menu. Adjusting the setting for the customer is not a warrantable defect.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2018 C-Max, 2013-2019 Escape/Fusion/MKZ, 2015-2018 Focus, 2015-2019 Edge/F150/MKC/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017 Super Duty, 2018-2019 EcoSport/Expedition, and 2019 Nautilus vehicles may experience seat pan looseness, lateral movement, or clunk/thump noise on turns. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. For all turbocharged engine applications, the turbocharger oil supply filter (6C683 gas engine/6L625 connector style or 6A968 diesel engine) must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.
Source components: ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2013 2018 C-Max, Fusion, and MKZ Hybrid vehicles using SOBDM-C module connectors do not require electrical/dielectric grease. If used it may induce module communication concerns. Codes present may be U0293 and a P0AA6. The Workshop Shop Manual (WSM) does not state to use it on these module connectors.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2013-2019 vehicles equipped with a LKS system with customer complaints of steering wheel vibration, steering pull or vehicle drift may be due to an alert and/or steering aid input from the LKS. The LKS system detects unintentional drifting toward the outside of the lane and alerts and/or aids vehicle to stay in the lane. Be sure the customer understands how the lane departure warning feature settings work for Alert (steering wheel vibration) and Aid (steering input toward lane center). Further information on the LKS can be found in the owners manual. If the customers concern is due to the LKS functioning as intended, do not attempt to repair.
Source components: STEERING · STEERING: STEERING WHEEL/HANDLE BAR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When connecting the Vehicle Communication Module (VCM) and Integrated Diagnostic System (IDS) or Ford Diagnosis and Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic trouble codes (DTCs), no start, no crank conditions or the IPC inoperative. If a vehicle displays these issues, disconnect the equipment from the DLC and disconnect the vehicle battery. Wait 10 minutes and reinstall with the ignition off. Clear any DTCs present and retest.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2014-2019 Fusion and 2017-2019 Escape vehicles equipped with a 1.5L Ecoboost engine may exhibit coolant consumption and white smoke concern. Follow the Cooling System Pressure Test procedure in Workshop Manual(WSM), Section 303-03, pressurize the cooling system to 138 kPa (20 psi) and hold for 5 hours. If cooling system pressure drops 27.57kPa(4psi) after 5 hours and internal engine coolant loss is confirmed, further investigation of the head gasket interface is required. Carefully inspect cylinder block for erosion, pitting, and flatness. Defects will be between the engine block cylinders and cylinder bore bridges. If defects with the surface of the cylinder block and/or cylinder head are identified, follow WSM, Section 303-01A procedures for repairs. Complete cost cap as needed to determine the most cost effective repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2018 Fusion, MKZ and C-Max vehicles with 2.0L Gas/Electric engine may exhibit an illuminated MIL with DTC P013A in the Powertrain Control Module(PCM). This may be due to an exhaust system leak. Exhaust leak inspection should be conducted before performing Powertrain Control/Emissions Diagnostics PC/ED Manual diagnostic routines. Inspect for carbon soot/moisture witness marks at exhaust connections. Inspect welds including CMS Boss, flex pipe and flanges. Inspect Catalyst Monitor Sensor(CMS) threads and crush washer to confirm sensor is fully seated in pipe boss. Do not use Vacutec smoke machine to diagnose sensor leaks. Applying soapy water solution to exhaust connections including CMS threads, while exhaust flow is restricted at the tailpipe and exhaust system is pressurized at 5 PSI(do not exceed 5 PSI), will increase ability to identify and confirm leaks
NHTSA source summary · Original PDF not reviewed by Recallfolio
When connecting the Vehicle Communication Module (VCM) and Integrated Diagnostic System (IDS) or Ford Diagnosis and Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic trouble codes (DTCs), no start, no crank conditions or the IPC inoperative. If a vehicle displays these issues, disconnect the equipment from the DLC and disconnect the vehicle battery. Wait 10 minutes and reinstall with the ignition off. Clear any DTCs present and retest.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2018 Escape vehicles equipped with 1.5L/1.6L/2.0L EcoBoost, 2013-2018 Fusion vehicles equipped with 2.0L/2.7L EcoBoost, 2013-2018 MKZ vehicles equipped with 2.0L EcoBoost, 2017-18 MKZ vehicles equipped with 3.0L EcoBoost, 2015-2018 MKC vehicles equipped with 2.0L/2.3L EcoBoost, 2015-2018 Edge vehicles equipped with 2.0L/2.7L EcoBoost, 2016-2018 MKX vehicles equipped with 2.0L and 2.7L EcoBoost, 2016-2018 Explorer vehicles equipped with 2.3L EcoBoost, 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost and 2016-2018 Focus RS equipped with 2.3L EcoBoost may exhibit a dark black fluid leak from the right side transfer case intermediate shaft seal. Follow the Service Procedure to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2018 Fusion/Fusion HEV, 2017 Escape and 2017 F150/Raptor equipped with a Telematics Control Unit (TCU) may exhibit inoperative remote features via FordPass Mobile app, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 with no modem electronic serial number (ESN) displayed. To correct this condition, perform any open TCU field service actions (FSAs). If U0198 DTC still remains, remove the TCU fuse for 5 minutes then reinstall prior to programming. Reprogram the TCU using Integrated Diagnostic System (IDS) release 110.05 or higher. An internet connection is required. Calibration files may also be obtained at www.motorcraftservice.com. For claiming, use causal part 14G229 and applicable labor operations in section 10 of the SLTS manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2015-2018 Edge, Fusion, Focus, MKZ, MKC, Escape vehicles equipped with a 2.0L EcoBoost engine may exhibit coolant consumption, white smoke and/or a runs rough condition. Refer to the extended coolant pressure test and checking for combustion gases in Workshop Manual (WSM), Section 303-03A. If internal coolant loss is confirmed, further investigation of the head gasket interface is required. Carefully inspect the cylinder block and head for erosion, pitting, and flatness defects, primarily between the cylinder to cylinder bore bridges. If defects to the aluminum surface on the cylinder block and/or cylinder head are found, follow the cost cap tool for component replacement. Follow WSM, Section 303-01A for the repair procedures
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some Ford and Lincoln vehicles equipped with a 2.7L or 3.0L EcoBoost engine may exhibit an oil leak from the engine oil pan RTV seal. Replace the oil pan following the procedure in Workshop Manual (WSM) Section, 303-01. After removing the oil pan it is suggested to allow the crankcase to drain overnight to minimize the chance of residual oil contaminating the crankcase sealing rail. Remove all traces of old RTV and clean the engine sealing surface using only Motorcraftù Metal Brake Parts Cleaner, then wipe with Motorcraftù Metal Surface Prep Wipes and allow to air dry. Refer to WSM, Section 303-00 > RTV Sealing Surface Cleaning and Preparation. If possible, allow the new RTV sealant to cure for 4 hours before refilling the engine with oil. Skipping or improperly completing steps may result in repeat oil pan leaks.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2018 Ford and Lincoln vehicles equipped with SYNC 3 not at the latest software level may exhibit Various Performance Related concerns such as Display Operation, Navigation, Voice Recognition, Phone Pairing, Applink, Travel Link, Slow System Response, etc. Check for SYNC software update under the OASIS Tab SYNC selection. If an update is available refer to WSM, Section 415-00 and update the APIM software. After Installation, complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2018 Continental, MKC, MKX, MKZ, and Fusion vehicles with an instrument panel center mounted speaker and 2017-2018 Escape vehicles with Sony audio systems may exhibit an inoperative speed compensated volume feature. This may be due to the calibration in the audio control module (ACM). To correct the concern, reprogram the ACM to the latest calibration using the appropriate Ford scan tool release 110.03 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. For claiming, use causal part 18C869 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2018 Ford and Lincoln vehicles with SYNC 3 may exhibit an intermittent blue or black screen. Check for SYNC software update under the OASIS Tab SYNC selection. If update is available refer to WSM, Section 415-00 and update APIM software. After Installation Complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various 2016-2018 vehicles with SYNC 3 may experience a touch screen that does not respond to any input. Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some Ford and Lincoln vehicles equipped with a 2.7L or 3.0L EcoBoost engines may exhibit an oil leak from the engine oil pan RTV seal. Replace the oil pan by performing the published Workshop Manual (WSM) service procedures. After removing the oil pan, it is suggested to allow the crankcase to drain overnight to minimize the chance of residual oil contaminating the crankcase sealing rail. Remove all traces of old RTV, clean the engine sealing surface with only Motorcraftù Metal Brake Parts Cleaner then wipe with Motorcraftù Metal Surface Prep Wipes, and allow to air dry as directed in WSM, Section 303-00, RTV Sealing Surface Cleaning and Preparation. If possible, after the new oil pan is installed, allow the new RTV sealant to cure for 4 hours before refilling the engine with oil. Ford is investigating this concern. Monitor OASIS for future updates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 Fusion/MKZ/MKC/Escape/Edge vehicles equipped with a 2.0L EcoBoost engine may exhibit a runs rough condition with DTCs P0300, P0301, P0302, P0303, P0304 and/or P0316. This may be due to coolant intrusion due to corrosion on the engine block. To diagnose this concern, with the engine at normal operating temperature, pressurize the cooling system to 138 kPa (20 psi) and hold for 5 hours. If the coolant pressure drops 27.57 kPa (4psi), remove the spark plugs and inspect for coolant in the cylinders. If coolant is found in any of the cylinders, replace the engine long block assembly. Follow normal prior approval process for your Dealership. However, follow the diagnostic repair procedure in this article to determine correct repair. For claiming, use causal part 6006 and applicable labor operations in Section 6 of the SLTS Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Replacing the original equipment SYNC/Navigation system with either an aftermarket SYNC/Navigation kit or modifying original SYNC/Navigation parts to provide additional features is not recommended nor supported on any Ford, Mercury or Lincoln vehicle. Only approved Genuine Ford accessories or originally installed systems are supported and certified to function correctly with other vehicle systems. If you suspect a system has been modified, the following resources can be used to verify original equipment: Monroney Label (Window Sticker), Professional Technician Society (PTS) OASIS tab select SYNC or HVBOM. For Genuine Ford accessories use: PTS Workshop Tab select Dealer Installed Accessory or Accessory Installation.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2018 Fusion vehicles equipped with 2.7L and MKZ vehicles equipped with 2.0L or 3.0L Ecoboost vehicles without painted calipers and built on or before 5-Mar-2018, may exhibit a brake moan noise from the rear when backing up on the first application in the morning. To resolve this concern, replace the rear brake pads with a new brake pad kit part number JG9Z-2200-A. The brake pad kit contains a unique grease packet which must be used in conjunction with the new brake pads to resolve the concern. Refer to Workshop Manual (WSM), Section 206-00 for installation. For claiming, use causal part 2200 and applicable labor operations in section 2 of the service labor time standards (SLTS) manual.
Source components: BACK OVER PREVENTION: REARVIEW SYSTEM BRAKING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2018 Ford and Lincoln vehicles equipped with SYNC 3 and connected to an iPhone recently upgraded to iOS 11.2.5 may exhibit functional concerns where USB audio playback and App Link will not operate. This may also include, under certain conditions, no Bluetooth streaming. Apple has released iOS 11.2.6 to address this concern. Advise the customer to update the device to iOS 11.2.6 and re-evaluate before performing any diagnosis or repairs for this condition. To check the iOS software level on an Apple iOS device, select Settings > General > About on the device.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2012-2018 Focus Electric, 2013-2017 C-Max Energi, and 2013-2018 Fusion Energi plug-in hybrid electric vehicles (PHEV) may exhibit the high voltage (HV) battery failing to charge while connected to the Delphi 120 volt electric vehicle service equipment (EVSE) charge cord. To identify a Delphi EVSE the coupler on the EVSE that connects to the vehicle charge port is solid black. For information on the Delphi EVSE indicator status used for diagnostics, reference High Voltage Battery > Charging the High Voltage Battery in the Owners Guide for a 2018 Fusion Energi. Reference the Convenience Cord Light Emitting Diode (LED) Indicators chart. The Workshop Manual (WSM) is scheduled to be revised at a later date.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2017 C-MAX Energi, 2013-2018 Fusion Energi, 2013-2018 C-MAX/Fusion Hybrid/MKZ Hybrid may exhibit a no start with battery energy control module (BECM) diagnostic trouble code (DTC) P0AE5. For 2015-2017 C-MAX Energi refer to the 2014 MY C-MAX Workshop Manual (WSM), Section 414-03A for normal diagnostics. For all vehicles, if WSM pinpoint testing for BECM DTC P0AE5 finds the DC/DC converter control module (14B227), cabin coolant heater (18K463) or A/C compressor (19703) has low high voltage circuit internal resistance, only replace the component found with low internal resistance. It is not necessary to replace the high voltage battery junction (10C666) along with the low resistance high voltage component. The WSM is currently under revision.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2018 Ford and Lincoln Vehicle equipped with SYNC 3 and connected to an iPhone recently upgraded to iOS 11.2.5 may exhibit a concern where USB Audio playback and App Link applications will not function properly. This may also include, under certain conditions, no Bluetooth Streaming. Apple is aware of the issue and is working on a resolution with a future iOS release. No repairs should be performed at this time. To check the iOS software level on an Apple iOS device, select Settings > General > About on the device. Monitor OASIS for updates. Customers can also check Apple Support or connect to iTunes for the latest available iOS release for their phone.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2018 Energi and Hybrid vehicles may exhibit a fuel door opening delay longer than 15 sec or unable to open condition without refueling system or fuel door related DTCs. This condition may be due to the high pressure fuel tank pressure transducer (HPFTPT) functionality. Check the HPFTPT after opening the fuel door by releasing the mechanical lever located in the trunk. Install supplemental refueling adaptor in the vehicle to open the capless fuel tank filler pipe. During key on engine off (KOEO) condition check if the fuel tank pressure transducer (FTPT) voltage is between 1.4 1.54 V at atmospheric pressure in the tank. If the voltage is within the range, FTPT is functioning as intended. Check the fuel vapor vent valve (FVVV), also called refueling valve, integrity by following Workshop Manual (WSM), Section 310-00.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2010-2018 various vehicles equipped with SYNC or SYNC 3 may not function when attempting to find or use the Spotify app via AppLink. As of an update released on 1/15/2018 Spotify will no longer be supporting their AppLink integration. No repair attempts should be attempted to correct this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When connecting the Vehicle Communication Module (VCM) and Integrated Diagnostic System (IDS) or Ford Diagnosis and Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic trouble codes (DTCs), no start or no crank conditions or the IPC inoperative. For Lincoln vehicles, this information is now listed in the Technical Inspection and Post Road Test Sections of ePDI on the PTS website. If a vehicle displays these issues, disconnect the equipment from the DLC and disconnect the vehicle battery. Wait 10 minutes and reinstall with the ignition off. Clear any DTCs present and retest.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The Accessory (Wireless) Keyless Entry Keypad can only be used with vehicles that are factory built with Remote Keyless Entry (RKE). The master code for the Accessory (Wireless) Keyless Entry Keypad can be retrieved from FMCDealer - Parts and Service - Parts Product Line Information - Keys/Entry Devices - Aftermarket Keyless Entry Keypad Code Access. Access to this site is granted through Dealer Program Enrollment System (DPES) and Dealer Principal, General Manager or Parts and Service Director can authorize users. Once authorized the retrieval process for master code can be obtained. The master code for the Accessory Keyless Entry Keypad cannot be retrieved from the body control module(BCM) with a diagnostic tool.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The EV Range after fully charging a Focus Electric, C-MAX/Fusion Energi may vary after each charge event. The window sticker indicates 0-20 mile range for C-MAX Energi, 0-21 mile range for Fusion Energi. Variation of EV range may not indicate a battery or charging concern. EV range is similar to the DTE display on gasoline vehicles, EV range will vary with driving/operating conditions. Conditions include: extreme outside temperatures, terrain, driving style, city or highway driving, tire pressure, and use of accessories. If the customer replaces the low roll resistance tires with a more aggressive tread the range will suffer. Using the cabin heater and A/C, which are electric, will also decrease EV range. To temporarily remove the impact of driving/climate history , reset the Driving History/Lifetime Summary by using the Settings menu on the left side of the instrument cluster, under Display
NHTSA source summary · Original PDF not reviewed by Recallfolio
The Accessory (Wireless) Keyless Entry Keypad can only be used with vehicles that are factory built with Remote Keyless Entry (RKE). The master code for the Accessory (Wireless) Keyless Entry Keypad can be retrieved from FMCDealer - Parts and Service - Parts Product Line Information - Keys/Entry Devices - Aftermarket Keyless Entry Keypad Code Access. Access to this site is granted through Dealer Program Enrollment System (DPES) and Dealer Principal, General Manager or Parts and Service Director can authorize users. Once authorized the retrieval process for master code can be obtained. The master code for the Accessory Keyless Entry Keypad cannot be retrieved from the body control module(BCM) with a diagnostic tool.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The EV Range after fully charging a Focus Electric, C-MAX/Fusion Energi may vary after each charge event. The window sticker indicates 0-20 mile range for C-MAX Energi, 0-21 mile range for Fusion Energi. Variation of EV range may not indicate a battery or charging concern. EV range is similar to the DTE display on gasoline vehicles, EV range will vary with driving/operating conditions. Conditions include: extreme outside temperatures, terrain, driving style, city or highway driving, tire pressure, and use of accessories. If the customer replaces the low roll resistance tires with a more aggressive tread the range will suffer. Using the cabin heater and A/C, which are electric, will also decrease EV range. To temporarily remove the impact of driving/climate history , reset the Driving History/Lifetime Summary by using the Settings menu on the left side of the instrument cluster, under Display
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2018 Escape/Fusion/MKZ vehicles equipped with 2.5L or 1.5L/2.0L/3.0L Ecoboost engine, 2015-2018 MKC/Edge/Explorer vehicles equipped with 2.0L/2.3L/2.7L EcoBoost engine, 2016-2018 MKX vehicles equipped with 2.7L Ecoboost engine, 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost, and AWD may exhibit a fluid leak from the PTU intermediate shaft seal. Replacement of the intermediate shaft seal seal does not require removal of the PTU and does not require the use of the cover seal and bolt kit (CV6Z-7275-K) to perform the repair. Refer to the Workshop Manual (WSM), Section 308-07.
Source components: ENGINE · POWER TRAIN:TRANSFER CASE (4-WHEEL DRIVE).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2018 Escape/Fusion/MKZ vehicles equipped with 2.5L or 1.5L/2.0L/3.0L Ecoboost engine, 2015-2018 MKC/Edge/Explorer vehicles equipped with 2.0L/2.3L/2.7L EcoBoost engine, 2016-2018 MKX vehicles equipped with 2.7L Ecoboost engine, 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost, and AWD may exhibit a fluid leak from the PTU intermediate shaft seal. Replacement of the intermediate shaft seal seal does not require removal of the PTU and does not require the use of the cover seal and bolt kit (CV6Z-7275-K) to perform the repair. Refer to the Workshop Manual (WSM), Section 308-07.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2018 Ford or Lincoln vehicles equipped with SYNC 3 may exhibit a blank screen or other various SYNC symptoms only when the vehicle is in transport mode. This is due to the power saving features enabled while in transport mode and is beneficial for battery life to keep the vehicle in transport mode until the vehicle is prepped for sale. To prevent a SYNC system lockup during transport mode deactivation, follow the Workshop Manual (WSM) procedure allowing time for the SYNC system to complete all tasks such as fully booting up or powering down and shutting off before moving to the next step of the procedure. If the vehicle exhibits a blank screen or SYNC symptoms after transport mode deactivation, refer to WSM, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 F150/Edge, 2016-2018 MKX and 2017-2018 Fusion, Continental vehicles equipped with a 2.7L engine may experience a malfunction indicator lamp (MIL) and/or wrench lamp with Diagnostic Trouble Codes (DTCs): P0116, P0117, P0118, P0119, P0217, P0330, P1026, and/or P130D. This may be due to a engine coolant temperature (ECT) sensor connector which is not fully seated or damaged wiring between connectors C1064 and C1047 for F150 and C1016 and C1168 for Edge/MKX/Fusion/Continental vehicles. ECT sensors should not be replaced if damaged wiring is found at or near these connectors. If an issue with the wiring is found use causal part 12A699.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2018 Fusion/MKZ vehicles built on or before 27-Oct-2017 may exhibit an illuminated airbag lamp and/or SYNC 911 assist not operational message being displayed. Connect the IDS and check the RCM and APIM for DTCs. If any of the following RCM DTCs U3000, U2100, U2101, U2300, U0455, B0080, B141B, B141C, B0054, B140C, B140D, B0057, B140E, B140F and/or APIM DTC U0452 is stored, then reprogram the RCM to the latest level using IDS or FJDS 107.04 or higher. After reprograming, perform an as-built configuration of the RCM. Make sure you are connected to the internet when entering module programming to obtain the latest updates. For claiming, use causal part 14B321 and applicable labor operations in section 10 of the service labor time standards (SLTS) manual. Calibration files may also be obtained at www.motorcraftservice.com
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit a no start condition with an illuminated malfunction indicator lamp (MIL) and a DTC P161A after PCM replacement. This may be due to the parameter reset procedure not being properly completed. To clear this DTC, use the Ford Integrated Diagnostic System (IDS) service tool or Ford J2534 Diagnostic Software, select - Toolbox - Body - Security - PATS Functions - Parameter Reset. Follow the on-screen instructions to complete the procedure. This procedure will transfer the existing Key ID information between the modules without the need of having 2 programmed PATS keys present. There is no need to program keys when the PCM is going to be replaced. Additional information can be found in the Workshop Manual (WSM), Section 419-01. Missing or lost keys are not warrantable.
Source components: ELECTRICAL SYSTEM · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2018 Fusion and MKZ vehicles equipped with a 2.0L Gasoline Turbocharged Direct Injection (GTDI) engine and built on or before 29-Sep-2017 may exhibit an illuminated MIL with DTC P04DB (crankcase ventilation system disconnected) in the powertrain control module (PCM) memory. Reprogram the powertrain control module (PCM) using Integrated Diagnostic System (IDS) or Ford J2534 Diagnostic Software (FJDS) release 107.04 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. Calibration files may also be obtained at www.motorcraftservice.com.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2018 Fusion vehicles equipped with a 2.5L engine and built on or before 18-Aug-2017 may exhibit an illuminated MIL with Diagnostic Trouble Codes (DTCs) P0071 and/or P068A. Reprogram the powertrain control module (PCM) using Integrated Diagnostic System (IDS) or Ford J2534 Diagnostic Software (FJDS) release 107.03 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. Calibration files may also be obtained at www.motorcraftservice.com
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2018 Fusion SE fleet vehicles equipped with SYNC may have a right side instrument cluster display which is blank and does not respond to inputs from the steering wheel controls. This is a normal condition. For fleet vehicles, equipped with this build combination, the instrument cluster is not configurable and will not respond to inputs from the steering wheel controls. Do not attempt to make repairs for this condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017 and 2018 Fusion vehicles equipped with the 2.5L engine and built on or before 18-Aug-2017 without active grille shutters may exhibit a concern of a discharged battery. Battery drain may be a result of key-off load conditions resulting from the powertrain control module (PCM) remaining powered after stop/start button cycling. PCM battery drain may not be reproducible under some circumstances, especially after a battery has been discharged or if the battery has been disconnected. Follow the Service Procedure steps to correct the condition.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2018 Ford or Lincoln vehicles equipped with SYNC 3 may exhibit a blank screen or other various SYNC symptoms only when the vehicle is in transport mode. This is due to the power saving features enabled while in transport mode and is beneficial for battery life to keep the vehicle in transport mode until the vehicle is prepped for sale. To prevent a SYNC system lockup during transport mode deactivation, follow the Workshop Manual (WSM) procedure allowing time for the SYNC system to complete all tasks such as fully booting up or powering down and shutting off before moving to the next step of the procedure. If the vehicle exhibits a blank screen or SYNC symptoms after transport mode deactivation, refer to WSM, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2018 Fusion/MKZ/MKC/MKX/Continental with all audio systems and 2017-2018 Escape with Sony audio systems may exhibit an inoperative speed compensation volume feature. Do not attempt any repairs at this time. Engineering is investigating, monitor OASIS for updates.