The manufacturer’s record · Page 1 of 2
Original record summaries, dates and identifiers for this model-year. Records 1–100 of 153, ordered newest first. Dated records on this page: Jan 8, 2018–May 2, 2026.
Back to 2016 Ford FUSION problems & recallsThis archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
NHTSA communication ID: 11033582
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2014-2016 Model Year Fusion Vehicles Equipped With 1.5L Engine - Powertrain Control Module (PCM) Reprogramming
Campaign / software reference: 25E01
Source components: POWER TRAIN.
Source record 11033582 at NHTSANHTSA communication ID: 11029052
NHTSA source summary · Original PDF not reviewed by Recallfolio
Ford and Lincoln vehicles equipped with wired keyless entry keypad systems and accessory wireless keyless entry keypad systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k
Source components: ELECTRICAL SYSTEM · STRUCTURE:BODY · UNKNOWN OR OTHER.
Source record 11029052 at NHTSANHTSA communication ID: 11029721
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2013-2014 Model Year Escape and 2013-2016 Fusion Vehicles Equipped with a 6F35 Transmission Shift Cable Bushing Inspection and Protective Service Cap Installation
Source components: POWER TRAIN.
Source record 11029721 at NHTSANHTSA communication ID: 11025611
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. Pinpoint test HK in the Powertrain Control and Emissions Diagnosis (PC/ED) or in Section 303-14 of the Workshop Manual (WSM) has been updated to address this concern.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
Source record 11025611 at NHTSANHTSA communication ID: 11024707
NHTSA source summary · Original PDF not reviewed by Recallfolio
The affected vehicles have an emissions control system that may not control tailpipe emissions effectively over time.
Source components: FUEL/PROPULSION SYSTEM · UNKNOWN OR OTHER.
Source record 11024707 at NHTSANHTSA communication ID: 11008948
NHTSA source summary · Original PDF not reviewed by Recallfolio
While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions. While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions.
Source components: UNKNOWN OR OTHER.
Source record 11008948 at NHTSANHTSA communication ID: 11006953
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2014-2015 Model Year Fiesta, 2014-2016 Model Year Fusion, MKZ and 2014-2016 Model Year Transit Connect Vehicles Not Covered in Safety Recall: 20S15 or 23S36 Door Latch Replacement and Inspection
Source components: UNKNOWN OR OTHER.
Source record 11006953 at NHTSANHTSA communication ID: 10254138
NHTSA source summary · Original PDF not reviewed by Recallfolio
All accessory stick-on keyless entry keypads come with a wallet card containing the master code. If the accessory keypad was factory installed, this card will be placed in the glove box and should be handed to the vehicles owner during initial delivery. Unlike the integrated (wired) factory keypad, the accessory keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool. If the wallet card for an accessory keypad is lost, follow these steps to recover the code. Dealer Key Code access is granted through the Dealer Program Enrollment System (DPES); dealership management can authorize users. The authorized user must go to FMCDealer.com > Parts and Service > Parts Product Line Information > Keys/Entry Devices > Aftermarket Keyless Entry Keypad Code Access. Follow the instructions on the screen to obtain the master code for the accessory keypad.
Source components: EQUIPMENT.
Source record 10254138 at NHTSANHTSA communication ID: 10251952
NHTSA source summary · Original PDF not reviewed by Recallfolio
For 2015-2024 Ford and Lincoln vehicles equipped with turbocharged engines and customer concern of an engine oil leak, refer to Workshop Manual (WSM), Section 303-00 for oil leak inspection and testing methods. Ford has evaluated turbochargers replaced for oil leak symptoms and although oil may collect on the external surface of a turbocharger, it is extremely rare for a turbocharger assembly to be the root cause of the oil leak. Careful inspection of the turbocharger oil feed and drain tubes should be performed along with the recommended WSM procedures as needed. Warranty claims for turbocharger replacement going forward will be assessed.
Source components: ENGINE AND ENGINE COOLING.
Source record 10251952 at NHTSANHTSA communication ID: 10235153
NHTSA source summary · Original PDF not reviewed by Recallfolio
For 2000-2024 Ford and Lincoln vehicles, swapping a module from a vehicle for diagnosis purposes is likely to cause errors and is not recommended. It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.
Source components: STRUCTURE.
Source record 10235153 at NHTSANHTSA communication ID: 10233681
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2014-2020 Fusion and 2017-2019 Escape vehicles may be equipped with a 1.5L Ecoboost engine that uses a 50-tooth variable camshaft timing (VCT) intake and exhaust unit from the assembly plant or if a service long block was installed. VCT locking tool 303-1097 is not compatible with this system. If VCT system service is required, replace both the intake VCT (service part DS7Z-6256-F) and exhaust VCT (service part DS7Z-6256-G) as a pair. An interim loaner tool program has been established to enable these repairs. Contact 1-800-403-4844 (Monday-Friday 8:00am to 8:00pm EST; Saturday 8:00am to 3:00pm EST) to obtain this tool. A VCT locking tool compatible with the 50-tooth system is under development and will be sent to dealerships. Continue to monitor OASIS for additional information.
Source components: ENGINE AND ENGINE COOLING.
Source record 10233681 at NHTSANHTSA communication ID: 10228876
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
Source components: SERVICE BRAKES.
Source record 10228876 at NHTSANHTSA communication ID: 10226752
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2016 Escape/Fusion/MKZ vehicles may display an error message when updating the All Wheel Drive-ATC Barcode using the IDS service function after installing a new rear drive unit assembly (RDU) or active torque coupling (ATC) clutch assembly. To prevent this error from occurring, enter the universal ATC 4 digit barcode 7772. Once programmed, perform several figure 8 turns at parking lot speeds to verify there is no binding from the all wheel drive (AWD) system. If the vehicle binds in a turn, perform Pinpoint Test A. Refer to the Workshop Manual (WSM), Section 308-07A > Diagnosis and Testing.
Source components: SERVICE BRAKES.
Source record 10226752 at NHTSANHTSA communication ID: 10225458
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2020 Fusion, MKZ and 2013-2018 C-Max vehicles equipped with an HF35 transmission may exhibit a thumping/rubbing or grinding noise coming from the transmission. The noise may be present in all gear ranges including neutral when the vehicle is moving but will not be present when the vehicle is stationary or in park.
Source components: POWER TRAIN.
Source record 10225458 at NHTSANHTSA communication ID: 10225447
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 Fusion/MKZ vehicles equipped with a 2.0L EcoBoost engine may exhibit a rattle noise from the transmission bellhousing area. This may be more noticeable at idle. This may be due to a flexplate crack around the mounting area. To correct the condition, follow the Service Procedure to replace the flexplate, transmission fluid pump, and torque converter.
Source components: POWER TRAIN.
Source record 10225447 at NHTSANHTSA communication ID: 10222788
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
Source components: SERVICE BRAKES, HYDRAULIC.
Source record 10222788 at NHTSANHTSA communication ID: 10225540
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2015-2019 Model Year Edge and Lincoln MKX Vehicles and 2013-2018 Model Year Fusion and Lincoln MKZ Vehicles Front Brake Flexible Hose Replacement REASON FOR THIS SUPPLEMENT Parts Requirements / Ordering Information: Part numbers for Edge and MKX vehicles have been added. Edge and MKX model year updated from 2018 to 2019, build dates remain the same.
Source components: SERVICE BRAKES.
Source record 10225540 at NHTSANHTSA communication ID: 10222518
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2015-2018 Model Year Edge and Lincoln MKX Vehicles and 2013-2018 Model Year Fusion and Lincoln MKZ Vehicles Front Brake Flexible Hose Replacement Submitting Owner Letters
Source components: SERVICE BRAKES.
Source record 10222518 at NHTSANHTSA communication ID: 10218898
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2015-2018 Model Year Edge and Lincoln MKX Vehicles and 2013-2018 Model Year Fusion and Lincoln MKZ Vehicles Front Brake Flexible Hose Replacement In some of the affected vehicles, brake fluid may leak from one or both front brake flexible hoses. If the brake fluid reservoir is depleted below a predetermined level, the brake fluid warning indicator light will illuminate. The driver may experience an increase in pedal travel together with a reduction in the rate of deceleration over time.
Source components: SERVICE BRAKES.
Source record 10218898 at NHTSANHTSA communication ID: 10218621
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2014-2019 Fusion vehicles built on or before 10-Jun-2019 and 2017-2019 Escape vehicles built on or before 08-Apr-2019 equipped with a 1.5L EcoBoost engine may exhibit low coolant level, white exhaust smoke and/or runs rough condition with or without an illuminated malfunction indicator light (MIL) with only diagnostic trouble codes (DTCs) P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To resolve the condition, follow the Service Procedure to replace the short block and head gasket.
Source components: ENGINE AND ENGINE COOLING.
Source record 10218621 at NHTSANHTSA communication ID: 10218617
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2017 C-MAX Energi, 2013-2018 Focus battery electric vehicle (BEV), 2013-2020 Fusion plug-in hybrid electric vehicle (PHEV), 2015-2017 MKZ/MKZ Hybrid/MKC, 2016-2017 MKX and 2017 Continental vehicles equipped with 8 inch or larger center display screen may be unable to complete modem authorization after 3G to 4G modem upgrade was performed. No Authorization Pop-up will be displayed on the center display screen during the Authorization process. The vehicle may also not have proper functionality of remote app features such as remote start, return odometer, fuel information, or vehicle location incorrect in the app. This may be due to the SYNC software. To correct the condition, follow the Service Procedure to toggle Valet Mode.
Source components: EQUIPMENT:ELECTRICAL:INFOTAINMENT.
Source record 10218617 at NHTSANHTSA communication ID: 10214758
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2017 C-MAX Energi, 2013-2018 Focus battery electric vehicle (BEV), 2013-2020 Fusion plug-in hybrid electric vehicle (PHEV), 2015-2017 MKZ/MKZ Hybrid/MKC, 2016-2017 MKX and 2017 Continental vehicles equipped with SYNC screens 8 inch or larger may be unable to complete modem authorization after 3G to 4G modem upgrade was performed. No Authorization Popup will be displayed on SYNC infotainment screen during the Authorization process. The vehicle may also not have proper functionality of remote app features such as remote start, and return odometer and fuel information to the app. This may be due to the SYNC software. To correct the condition, follow the Service Procedure to toggle Valet Mode.
Source components: ELECTRICAL SYSTEM:PROPULSION SYSTEM:HYBRID MANAGEMENT:POWER CONTROL UNIT/MODULE (HPCU):SOFTWARE · UNKNOWN OR OTHER.
Source record 10214758 at NHTSANHTSA communication ID: 10212957
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2023 Ford or Lincoln vehicles with modems activated through FordPass or LincolnWay may experience 12 volt battery drain symptoms when the customer uses non-Ford/Lincoln phone applications as an alternate channel to access vehicle commands such as door lock/unlock, remote start, vehicle location, etc. The battery drain may be caused by excessive calls for data through the vehicle network keeping it in an activated state. Recommend that the customer uninstall the app to ensure this is not contributing to battery symptoms experienced. Advise the customer that unaffiliated third-party app developers do not work directly with Ford to adhere to security, vehicle communication, and privacy requirements.
Source components: ELECTRICAL SYSTEM.
Source record 10212957 at NHTSANHTSA communication ID: 10211728
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2020-2022 Escape, 2021-2022 Corsair, 2022 Maverick vehicles equipped with HF35/HF45 hybrid transmissions can now be disassembled to repair and clean any contamination that may have been the result of a differential or transfer shaft bearing failure and the transmission can be overhauled/rebuilt. Service tools and service parts are now available. Refer to the Workshop Manual, Section 307-01.
Source components: POWER TRAIN.
Source record 10211728 at NHTSANHTSA communication ID: 10211709
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2014-2017 C-MAX Energi, 2014-2020 Fusion plug-in hybrid electric vehicle (PHEV), 2015-2017 MKZ/MKZ Hybrid/MKC, 2016-2017 MKX, 2016-2018 Focus battery electric vehicle (BEV) and 2017 Continental vehicles equipped with SYNC screens 8 inch or larger may be unable to complete modem authorization after 3G to 4G modem upgrade was performed. No Authorization Popup displayed on SYNC infotainment screen during the Authorization process. This may be due to the Sync Software. To correct the condition, follow the Service Procedure to toggle Valet Mode.
Source components: ELECTRICAL SYSTEM · ENGINE.
Source record 10211709 at NHTSANHTSA communication ID: 10210730
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2016 Fusion, 2013-2018 C-MAX, 2014-2019 Escape, 2014-2021 Transit Connect, and 2015-2018 Edge vehicles may indicate an incorrect shifter lever position. This may be due to the bushing at the transmission end of the shifter lever cable resulting in a mismatch of cluster and selected gear position. To correct the condition, follow the Service Procedure steps to replace the bushing and on certain vehicles install the protective cap over the selector at the transmission end of the selector lever cable.
Source components: POWER TRAIN.
Source record 10210730 at NHTSANHTSA communication ID: 10210392
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2014-2019 Fusion vehicles built on or before 10-Jun-2019 and 2017-2019 Escape vehicles built on or before 08-Apr-2019 equipped with a 1.5L EcoBoost engine may exhibit low coolant level, white exhaust smoke and/or runs rough condition with or without an illuminated malfunction indicator light (MIL) with only diagnostic trouble codes (DTCs) P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To resolve the condition, follow the Service Procedure to replace the short block and head gasket.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT.
Source record 10210392 at NHTSANHTSA communication ID: 10209209
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 21-2236 to update the models and year affected. Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2013-2022 Escape, 2015-2018 Focus, 2015-2019 MKC, 2015-2022 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2022 F-Super Duty, 2018-2022 EcoSport/Expedition, 2019-2022 Ranger/Nautilus, 2021-2022 Bronco/Bronco Sport/Mustang Mach-E, 2022 Maverick vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
Source components: EQUIPMENT · EQUIPMENT:MECHANICAL · SEATS.
Source record 10209209 at NHTSANHTSA communication ID: 10203848
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various 2014-2020 vehicles equipped with a 3G modem may experience a lack of 3G modem performance. This may be due to the 3G cellular service functionality being decommissioned starting August 2021 and through March 2022. As the 3G cellular service is decommissioned, vehicles equipped with the 3G telematics control unit (TCU) will lose MyFord Mobile and MyLincoln Mobile app functionality/connectivity. Repair or Replacement of the TCU should no longer be performed using existing service stock. Replacement of the 3G TCU for this concern will result in programming concerns and repairs should not be performed. The customer can pay to upgrade their 3G modem with a 4G modem by following the information in FSA 21B09. Refer to FSA 21B09 for reference and not for claiming.
Source components: COMMUNICATION:MANUFACTURER TELEMATICS · UNKNOWN OR OTHER.
Source record 10203848 at NHTSANHTSA communication ID: 10202708
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2020 Fusion/MKZ vehicles equipped with a 2.0L EcoBoost engine may exhibit a rattle noise from the transmission bellhousing area. This may be more noticeable at idle. This may be due to a flexplate crack around the mounting area. To correct the condition, follow the Service Procedure steps to replace the flexplate, transmission fluid pump, and torque converter.
Source components: ENGINE · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · POWER TRAIN.
Source record 10202708 at NHTSANHTSA communication ID: 10201614
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2014-2019 Fusion vehicles built on or before 10-Jun-2019 and 2017-2019 Escape vehicles built on or before 08-Apr-2019 equipped with a 1.5L EcoBoost engine may exhibit low coolant level, white exhaust smoke and/or runs rough condition with or without an illuminated malfunction indicator light (MIL) with only diagnostic trouble codes (DTCs) P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To resolve the condition, follow the Service Procedure to replace the short block and head gasket.
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
Source record 10201614 at NHTSANHTSA communication ID: 10201050
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK12 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: ELECTRICAL SYSTEM.
Source record 10201050 at NHTSANHTSA communication ID: 10201034
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2021 Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
Source components: SERVICE BRAKES, ELECTRIC:SOFTWARE/PROGRAMMING.
Source record 10201034 at NHTSANHTSA communication ID: 10199536
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2013-2021 Escape, 2015-2018 Focus, 2015-2019 MKC, 2015-2021 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2021 F-Super Duty, 2018-2021 EcoSport/Expedition, 2019-2021 Ranger/Nautilus, 2021 Bronco Sport/Mustang Mach-E vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
Source components: SEATS.
Source record 10199536 at NHTSANHTSA communication ID: 10194428
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN:AUTOMATIC TRANSMISSION.
Source record 10194428 at NHTSANHTSA communication ID: 10194434
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2016 Fusion, 2013-2018 C-MAX, 2014-2019 Escape, 2014-2021 Transit Connect, and 2015-2018 Edge vehicles may indicate an incorrect shifter lever position. This may be due to the bushing at the transmission end of the shifter lever cable resulting in a mismatch of cluster and selected gear position. To correct the condition, follow the Service Procedure steps to replace the bushing and on certain vehicles install the protective cap over the selector at the transmission end of the selector lever cable.
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · POWER TRAIN.
Source record 10194434 at NHTSANHTSA communication ID: 10190990
NHTSA source summary · Original PDF not reviewed by Recallfolio
Under Safety Recall 20S15, in some of the affected vehicles, the door latches have a pawl spring tab that may break. This condition will typically prevent the door from latching. If the customer is able to latch the door, after repeated attempts to shut the door, these is a potential the door may unlatch while driving, increasing the risk of injury. Ford's analysis indicates that this condition is more likely to happen in states and territories with high ambient temperatures. For 20R01, owners will be notified that if their vehicle exhibits door latching concerns or if they are concerned about the latches in their vehicles, they may request repairs under this regional program.
Source components: LATCHES/LOCKS/LINKAGES.
Source record 10190990 at NHTSANHTSA communication ID: 10189767
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2016 Fusion, 2013-2018 C-MAX, 2013-2019 Escape, 2014-2021 Transit Connect, and 2015-2018 Edge vehicles may indicate an incorrect shifter lever position. This may be due to the bushing at the transmission end of the shifter lever cable resulting in a mismatch of cluster and selected gear position. To correct the condition, follow the Service Procedure steps to replace the bushing and install the protective cap over the selector at the transmission end of the selector lever cable.
Source components: POWER TRAIN.
Source record 10189767 at NHTSANHTSA communication ID: 10180428
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2009-2020 Ford and Lincoln vehicles equipped with turbochargers may exhibit an oil leak from the turbocharger oil supply or return tubes, O-rings or 6.7L pedestal gasket. Although oil may collect on the turbocharger, it is very rare for a turbocharger to leak oil. To isolate the source of the leak, refer to Workshop Manual (WSM), Section 303-00 General Information > Diagnosis and Testing > Engine > Engine Oil Leaks - Fluorescent Oil Additive Method procedure. When an oil leak is present at a turbocharger oil supply or drain tube, remove the affected oil tube and inspect for damage, and replace the O-ring seals, pedestal gasket or oil tube as required. Refer to WSM, Section 303-04. For claiming, use the affected oil tube or pedestal gasket as the causal part and applicable labor operations in Sections 6 and 9 of the Service Labor Time Standards (SLTS) Manual.
Source components: ENGINE AND ENGINE COOLING.
Source record 10180428 at NHTSANHTSA communication ID: 10177863
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 19-2026 to update the vehicle model years affected. Some 2000 and newer Ford/Lincoln/Mercury vehicles equipped with aluminum body panels may exhibit corrosion concerns appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended.
Source components: STRUCTURE.
Source record 10177863 at NHTSANHTSA communication ID: 10177123
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2016 Fusion/MKZ/C-MAX vehicles equipped with an HF35 transmission and built on or before 15-Aug-2015 may exhibit a thumping/rubbing or grinding noise coming from the transmission. The noise may be present in all gear ranges including neutral when the vehicle is moving but will not be present when the vehicle is stationary or in park. This may be due to the differential side bearings and/or the transfer shaft and housing. To correct the condition, follow the Service Procedure to install either a transfer shaft kit or a remanufactured transmission assembly.
Source components: EQUIPMENT · POWER TRAIN.
Source record 10177123 at NHTSANHTSA communication ID: 10177042
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2020 Ford and Lincoln vehicles equipped with a SYNC 3 Touchscreen may experience the volume control unresponsive from the Front Control Interface Module (FCIM) and steering volume controls when using Apple Car Play. When the Apple device is removed, volume control is restored. This is due to a concern with the Waze Navigation App software and Apple iOS version. To correct the condition, update the Waze App software and iOS to the latest version available and reboot the customer's Apple device. Perform an ignition cycle and reconnect the Apple device via USB. Open Apple Car Play and confirm volume control is restored. Installing/Updating third party software/applications is not warrantable.
Source components: ELECTRICAL SYSTEM · EQUIPMENT.
Source record 10177042 at NHTSANHTSA communication ID: 10176123
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2012-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit an inoperative remote start with a 'Vehicle Failed To Start' message when using MyFord Mobile/Ford Pass/Lincoln Way mobile applications. The cellular cloud systems will only allow two remote start requests from the MyFord Mobile/Ford Pass/Lincoln Way apps without a vehicle drive event occurring. If a third remote start request is received, a Vehicle Failed To Start message will be displayed quickly in the mobile app. Once the vehicle is driven, the remote start counter is reset and will allow remote start commands to be sent from the mobile app. If the remote start system is not functioning using the key fob, refer to Workshop Manual (WSM) Section 303-06 for further diagnosis.
Source components: ELECTRICAL SYSTEM.
Source record 10176123 at NHTSANHTSA communication ID: 10175895
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2018 C-Max, 2013-2020 Escape/Fusion/MKZ, 2015-2018 Focus,2015-2019 MKC, 2015-2020 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2020 F-Super Duty, 2018-2020 EcoSport/Expedition, 2019-2020 Ranger/Nautilus vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
Source components: SEATS · STRUCTURE:FRAME AND MEMBERS:UNDERBODY SHIELDS.
Source record 10175895 at NHTSANHTSA communication ID: 10174400
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2014-2019 Fusion vehicles built on or before 10-Jun-2019 and 2017-2019 Escape vehicles built on or before 08-Apr-2019 equipped with a 1.5L EcoBoost engine may exhibit low coolant level, white exhaust smoke and/or runs rough condition with or without an illuminated malfunction indicator light (MIL) with only diagnostic trouble codes (DTCs) P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To resolve the condition, follow the Service Procedure to replace the short block and head gasket.
Source components: ENGINE AND ENGINE COOLING.
Source record 10174400 at NHTSANHTSA communication ID: 10172972
NHTSA source summary · Original PDF not reviewed by Recallfolio
SSM 48619 - Various Vehicles - Perimeter Alarm Armed And Original Vehicle Keys Cannot Be Accessed to Enter Vehicle - CAN Protection Strategy Some 2013-2016 Model Year Vehicles may exhibit a concern in which the Perimeter Alarm is active and the original keys cannot be accessed to disable the perimeter alarm. This concern would most often occur when a customer loses keys and the dealership is attempting to program new keys to the vehicle. The Workshop Manual (WSM), Section 419-01A Perimeter Anti-Theft Alarm - System Operation and Component Description has been updated to inform of the Controller Area Network (CAN) Protection Strategy. Follow the procedure outlined to prevent replacement of the Body Control Module (BCM) on CAN Protection Strategy equipped vehicles when original keys are lost and perimeter alarm is active. Refer to the WSM for further detail on the CAN Protection Strategy. Lost keys and replacement of BCM for lost keys is non-warrantable.
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
Source record 10172972 at NHTSANHTSA communication ID: 10170901
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2016 Fusion, MKZ and C-MAX vehicles equipped with an HF35 transmission and built on or before 15-Aug-2015 may exhibit a thumping/rubbing or grinding noise coming from the transmission. The noise may be present in all gear ranges including neutral when the vehicle is moving but will not be present when the vehicle is stationary or in park. This may be due to the differential side bearings and/or the transfer shaft and housing. To correct the condition, follow the Service Procedure to install either a transfer shaft kit or a remanufactured transmission assembly.
Source components: POWER TRAIN.
Source record 10170901 at NHTSANHTSA communication ID: 10169986
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2020 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: POWER TRAIN.
Source record 10169986 at NHTSANHTSA communication ID: 10169884
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 19-2139 to update the production fix date. Some 2014-2019 Fusion vehicles built on or before 10-Jun-2019 and 2017-2019 Escape vehicles built on or before 08-Apr-2019 equipped with a 1.5L EcoBoost engine may exhibit low coolant level, white exhaust smoke and/or runs rough condition with or without an illuminated malfunction indicator light (MIL) with only diagnostic trouble codes (DTCs) P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To resolve the condition, replace the short block and head gasket.
Source components: ENGINE AND ENGINE COOLING.
Source record 10169884 at NHTSANHTSA communication ID: 10168739
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2014-2019 Fusion vehicles built on or before 21-Feb-2019 and 2017-2019 Escape vehicles built on or before 06-Apr-2019 equipped with a 1.5L EcoBoost engine may exhibit low coolant level, white exhaust smoke and/or runs rough condition with or without an illuminated malfunction indicator light (MIL) with only diagnostic trouble codes (DTCs) P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To resolve the condition, replace the short block and head gasket.
Source components: ENGINE AND ENGINE COOLING.
Source record 10168739 at NHTSANHTSA communication ID: 10164599
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2014-2019 Fusion and 2017-2019 Escape with 1.5L engine may exhibit coolant usage and white smoke from exhaust. Follow Cooling System Pressure Test process in WSM, Section 303-03. Pressurize system to 138kPa(20 psi) and hold 5 hours. If system pressure drops 27.57kPa(4psi) after 5 hours and borescope inspection through spark plug holes shows coolant presence in bores, the short block must be replaced. Further teardown inspection is not required, nor is completing cost cap. Cost cap requirements are waived for repairs completed utilizing this SSM. Reuse the original cylinder head for the repair. Ford has found all returned 1.5L cylinder heads pass inspection and replacement was not required. Follow WSM, Section 303-01A for repair procedure and refer the parts catalog as needed. Any backorders experienced will be filled as quickly as possible.
Source components: ENGINE AND ENGINE COOLING.
Source record 10164599 at NHTSANHTSA communication ID: 10164596
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2020 vehicles equipped with an EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function. To support the proper diagnosis of this compressor, the EVDC control valve tester has been provided to each U.S. dealership (339-EVDC100). Ensure the A/C system has a full charge prior to any compressor diagnostics. To support the proper diagnosis of this compressor, the EVDC compressor tool must be used, and the results recorded in the Technician comments field with the warranty claim. This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.
Source components: EQUIPMENT:APPLIANCE:AIR CONDITIONER.
Source record 10164596 at NHTSANHTSA communication ID: 10164508
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2010-2020 vehicles may exhibit distorted glass with a subtle orange peel pattern or streaking etched into the surface. This is caused by hydrofluoric acid which is used in some car wash solutions as a cleaning agent. Hydrofluoric acid can attack the glass and cause visual distortion and/or discoloration on the outer surface which cannot be removed by further cleaning. If this type of distortion is found, inspect the area of the glass that is covered by the cowl and/or molding. The portion of glass that is covered by the cowl or molding will not be affected by the acid. Hydrofluoric acid damage is not a defect in material or workmanship and is not a warrantable condition.
Source components: VISIBILITY · VISIBILITY:GLASS, SIDE/REAR.
Source record 10164508 at NHTSANHTSA communication ID: 10164497
NHTSA source summary · Original PDF not reviewed by Recallfolio
For Ford and Lincoln vehicles that require positive or negative battery terminal replacement, it is not necessary to replace the complete battery cable harness (14300 and 14301) for this concern. Positive battery cable clamp BT4Z-14450-AA and negative battery cable clamp BT4Z-14450-BA are available for this type of repair. Do not cut or shorten the battery cable, instead carefully remove the affected battery cable clamp and clean the cable end as necessary to preserve wire length. Some rework may be necessary for some vehicle environments. Bend the new positive battery cable clamp as needed and crimp it to the existing battery cable. Make sure to use heat shrink tubing over the battery cable to battery cable clamp connection. Obtain the heat shrink tube locally.
Source components: ELECTRICAL SYSTEM.
Source record 10164497 at NHTSANHTSA communication ID: 10163593
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2019 vehicles may experience a no crank concern due to a security access key table error. When attempting to program keys or perform a parameter reset, the procedure may fail and the appropriate Ford diagnostic scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the body control module (BCM) is internally damaged and requires replacement. The BCM should only be replaced for this condition when the 232 key table error message is present. If the 232 key table error is not present, follow normal diagnostics for the no crank condition. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
Source components: ELECTRICAL SYSTEM.
Source record 10163593 at NHTSANHTSA communication ID: 10163592
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2014-2019 Fusion and 2017-2019 Escape vehicles with 1.5L Ecoboost engine exhibiting coolant consumption and white smoke from the exhaust. Follow Cooling System Pressure Test procedure in WSM, Section 303-03, and pressurize system to 138kPa(20 psi) and hold for 5 hours. If system pressure drops 27.57kPa (4psi) after 5 hours and borescope inspection through spark plug holes confirms coolant intrusion into the cylinders, short block replacement is required. Further teardown inspection is not required. Reuse the original cylinder head for the repair. Ford has found all returned 1.5L cylinder heads pass inspection and replacement was not required. Follow WSM, Section 303-01A procedures for repairs and refer the parts catalog as needed. Short block availability may be limited and temporary backorders will be filled as quickly as possible.
Source components: ENGINE AND ENGINE COOLING.
Source record 10163592 at NHTSANHTSA communication ID: 10163571
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2016 Fusion and MKZ vehicles may not have a valid 5 digit key code stored in the Ford key code retrieval system. If both keys are lost and the original selling dealer does not have the key code on file, a new lock set may be needed. For Fusion IKT (non push-button start) use lock set ES7Z-5422050-A, Fusion push-button start use lock set ES7Z-5422050-B, and for Lincoln MKZ use lock set DP5Z-5422050-A. Kits include pre-cut keys. The push-button start kits come with back-up key blades, but do not include passive key remotes which will need to be ordered separately. Rotunda, the Technical Assistance Center, or the Customer Relations Center will not have key code information.
Source components: ELECTRICAL SYSTEM · EQUIPMENT.
Source record 10163571 at NHTSANHTSA communication ID: 10162062
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 Edge and 2015-2019 Fusion/MKZ/Escape/MKC vehicles equipped with a 2.0L EcoBoost engine may exhibit a low coolant level, white exhaust smoke and/or a runs rough condition with or without an illuminated malfunction indicator lamp (MIL). Diagnostic trouble codes (DTCs) may include P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To correct the condition, follow the Service Procedure steps to replace the long block engine assembly.
Source components: ENGINE AND ENGINE COOLING.
Source record 10162062 at NHTSANHTSA communication ID: 10160931
NHTSA source summary · Original PDF not reviewed by Recallfolio
On vehicles equipped with an automatic transmission it is imperative that the converter pilot hub be greased with Motorcraft Multi-Purpose Grease Spray XL-5-A even if grease was not applied from the factory. Also verify that the engine/transmission alignment dowel pins are present as well as the engine crankshaft dowel pin, if equipped, when installing the transmission. Failure to adequately lubricate the converter hub greatly increases the likelihood of the flexplate cracking in the future. Missing dowels may cause a misalignment issue also resulting in a premature failure. Refer to Workshop Manual (WSM), Section 307-01.
Source components: POWER TRAIN.
Source record 10160931 at NHTSANHTSA communication ID: 10160880
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2019 vehicles equipped with a EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.
Source components: EQUIPMENT:APPLIANCE:AIR CONDITIONER.
Source record 10160880 at NHTSANHTSA communication ID: 10159494
NHTSA source summary · Original PDF not reviewed by Recallfolio
SSM 47948 - 2010-2019 Various Vehicles - Turbocharged Engines - Oil Supply Filter Replacement When Replacing The Turbocharger Or The Turbocharger Oil Supply Tube For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. When specified in the WSM, the turbocharger oil supply filter must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.
Source components: ENGINE.
Source record 10159494 at NHTSANHTSA communication ID: 10159489
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2019 vehicles equipped with a EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:APPLIANCE:AIR CONDITIONER.
Source record 10159489 at NHTSANHTSA communication ID: 10156569
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2014-2019 Fusion and 2017-2019 Escape equipped with 1.5L Ecoboost engine may exhibit coolant consumption and white smoke concern. Follow the Cooling System Pressure Test procedure in WSM, Section 303-03, pressurize the cooling system to 138kPa(20 psi0 and hold for 5 hours. If cooling system pressure drops 27.57kPa(4psi) after 5 hours and internal engine coolant loss is confirmed, further investigation of the engine block surface to head gasket interface is required. Carefully inspect engine block cylinders and cylinder bore bridges for erosion, pitting, and flatness. If defects with the cylinder block surface are identified, follow WSM, Section 303-01A procedures for repairs. Complete cost cap as needed to determine the most cost effective repair. Ford has found that all returned cylinder heads pass inspection and may have been reused.
Source components: ENGINE AND ENGINE COOLING.
Source record 10156569 at NHTSANHTSA communication ID: 10156887
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2017 vehicles may experience a no crank concern due to a security access key table error. When attempting to program keys or perform a parameter reset, the procedure may fail and the Integrated Diagnostic System (IDS) scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the Body Control Module (BCM) is internally faulted and requires replacement. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
Source components: ELECTRICAL SYSTEM.
Source record 10156887 at NHTSANHTSA communication ID: 10155575
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2017 vehicles may experience a no crank concern due to a security access key table error. When attempting to program keys or perform a parameter reset, the procedure may fail and the Integrated Diagnostic System (IDS) scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the Body Control Module (BCM) is internally faulted and requires replacement. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
Source components: ELECTRICAL SYSTEM.
Source record 10155575 at NHTSANHTSA communication ID: 10156863
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2000 and newer Ford, Lincoln and Mercury vehicles equipped with aluminum body panels may exhibit corrosion concerns appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended. Follow the Service Procedure steps to correct the condition
Source components: EQUIPMENT · STRUCTURE.
Source record 10156863 at NHTSANHTSA communication ID: 10155551
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2000 and newer Ford, Lincoln and Mercury vehicles equipped with aluminum body panels may exhibit corrosion concerns appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended. Follow the Service Procedure steps to correct the condition
Source components: STRUCTURE.
Source record 10155551 at NHTSANHTSA communication ID: 10156874
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2019 Fusion/MKZ and 2013-2018 C-Max vehicles with 2.0L HEV/PHEV engine may exhibit multiple drivability or electrical concerns with one or more diagnostic trouble codes, being the most common P26C3, P26CA, P26D0, P2800, P2802, U019F and U0284. On Fusion/MKZ inspect connectors C146, C1651, C1812, C168C, C1717 and C134 for signs of water entry or corrosion. On C-Max, inspect connectors C134, C140, C144, C1651, C1717 and C1812 and service as necessary. NOTE: Connector C1717 is only equipped on PHEVs for both Fusion and C-Max.
Source components: ELECTRICAL SYSTEM · ENGINE.
Source record 10156874 at NHTSANHTSA communication ID: 10155562
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2019 Fusion/MKZ and 2013-2018 C-Max vehicles with 2.0L HEV/PHEV engine may exhibit multiple drivability or electrical concerns with one or more diagnostic trouble codes, being the most common P26C3, P26CA, P26D0, P2800, P2802, U019F and U0284. On Fusion/MKZ inspect connectors C146, C1651, C1812, C168C, C1717 and C134 for signs of water entry or corrosion. On C-Max, inspect connectors C134, C140, C144, C1651, C1717 and C1812 and service as necessary. NOTE: Connector C1717 is only equipped on PHEVs for both Fusion and C-Max.
Source components: ELECTRICAL SYSTEM.
Source record 10155562 at NHTSANHTSA communication ID: 10155548
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some all-wheel drive (AWD) 2013-2018 Escape vehicles equipped with 1.5L/1.6L/2.0L EcoBoost/Fusion vehicles equipped with 2.0L/2.7L EcoBoost/MKZ vehicles equipped with 2.0L EcoBoost, 2017-18 MKZ vehicles equipped with 3.0L EcoBoost, 2015-2018 MKC vehicles equipped with 2.0L/2.3L EcoBoost/Edge vehicles equipped with 2.0L/2.7L EcoBoost, 2016-2018 MKX vehicles equipped with 2.0L and 2.7L EcoBoost/Explorer vehicles equipped with 2.3L EcoBoost/Focus RS equipped with 2.3L EcoBoost, and 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost may exhibit a dark black fluid leak from the right side transfer case intermediate shaft seal. Follow the Service Procedure steps to correct the condition.
Source components: EQUIPMENT · POWER TRAIN.
Source record 10155548 at NHTSANHTSA communication ID: 10153969
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2012-2019 Vehicles may require repairs to the Smartlink system. Smartlink is a Ford Licensed Accessory which has a warranty provided by the accessory manufacturer. Warranty replacement parts for Smartlink that are ordered through Ford are not reimbursable through the Ford Motor Company warranty system. Please see the Warranty and Policy Manual for further information on Ford Licensed Accessories.
Source components: EQUIPMENT.
Source record 10153969 at NHTSANHTSA communication ID: 10153948
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2019 Ford and Lincoln vehicles equipped with SYNC 3 and a 6, 8 or 10 inch screen may show a pop-up message every key cycle that states 'SYNC can check for updates when connected to a WiFi network'. To remove the inconvenience of the pop-up the customer can either connect to a trusted WiFi network to complete the setup process or turn off WiFi in the WiFi settings located under the Settings menu. Adjusting the setting for the customer is not a warrantable defect.
Source components: ELECTRICAL SYSTEM.
Source record 10153948 at NHTSANHTSA communication ID: 10153931
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2018 C-Max, 2013-2019 Escape/Fusion/MKZ, 2015-2018 Focus, 2015-2019 Edge/F150/MKC/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017 Super Duty, 2018-2019 EcoSport/Expedition, and 2019 Nautilus vehicles may experience seat pan looseness, lateral movement, or clunk/thump noise on turns. Follow the Service Procedure steps to correct the condition.
Source components: EQUIPMENT · SEATS.
Source record 10153931 at NHTSANHTSA communication ID: 10152473
NHTSA source summary · Original PDF not reviewed by Recallfolio
For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. For all turbocharged engine applications, the turbocharger oil supply filter (6C683 gas engine/6L625 connector style or 6A968 diesel engine) must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.
Source components: ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER.
Source record 10152473 at NHTSANHTSA communication ID: 10152468
NHTSA source summary · Original PDF not reviewed by Recallfolio
2013 2018 C-Max, Fusion, and MKZ Hybrid vehicles using SOBDM-C module connectors do not require electrical/dielectric grease. If used it may induce module communication concerns. Codes present may be U0293 and a P0AA6. The Workshop Shop Manual (WSM) does not state to use it on these module connectors.
Source components: ELECTRICAL SYSTEM · EQUIPMENT.
Source record 10152468 at NHTSANHTSA communication ID: 10152466
NHTSA source summary · Original PDF not reviewed by Recallfolio
2013-2019 vehicles equipped with a LKS system with customer complaints of steering wheel vibration, steering pull or vehicle drift may be due to an alert and/or steering aid input from the LKS. The LKS system detects unintentional drifting toward the outside of the lane and alerts and/or aids vehicle to stay in the lane. Be sure the customer understands how the lane departure warning feature settings work for Alert (steering wheel vibration) and Aid (steering input toward lane center). Further information on the LKS can be found in the owners manual. If the customers concern is due to the LKS functioning as intended, do not attempt to repair.
Source components: STEERING · STEERING: STEERING WHEEL/HANDLE BAR.
Source record 10152466 at NHTSANHTSA communication ID: 10152464
NHTSA source summary · Original PDF not reviewed by Recallfolio
When connecting the Vehicle Communication Module (VCM) and Integrated Diagnostic System (IDS) or Ford Diagnosis and Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic trouble codes (DTCs), no start, no crank conditions or the IPC inoperative. If a vehicle displays these issues, disconnect the equipment from the DLC and disconnect the vehicle battery. Wait 10 minutes and reinstall with the ignition off. Clear any DTCs present and retest.
Source components: ELECTRICAL SYSTEM.
Source record 10152464 at NHTSANHTSA communication ID: 10148717
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2016 Fusion, MKZ and C-Max vehicles equipped with an HF35 transmission and built on or before 15-Aug-2015 may exhibit a thumping/rubbing or grinding noise coming from the transmission. The noise may be present in all gear ranges including neutral when the vehicle is moving but will not be present when the vehicle is stationary or in park. Follow the Service Procedure steps to correct the condition.
Source components: POWER TRAIN.
Source record 10148717 at NHTSANHTSA communication ID: 10148741
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2014-2019 Fusion and 2017-2019 Escape vehicles equipped with a 1.5L Ecoboost engine may exhibit coolant consumption and white smoke concern. Follow the Cooling System Pressure Test procedure in Workshop Manual(WSM), Section 303-03, pressurize the cooling system to 138 kPa (20 psi) and hold for 5 hours. If cooling system pressure drops 27.57kPa(4psi) after 5 hours and internal engine coolant loss is confirmed, further investigation of the head gasket interface is required. Carefully inspect cylinder block for erosion, pitting, and flatness. Defects will be between the engine block cylinders and cylinder bore bridges. If defects with the surface of the cylinder block and/or cylinder head are identified, follow WSM, Section 303-01A procedures for repairs. Complete cost cap as needed to determine the most cost effective repair.
Source components: ENGINE AND ENGINE COOLING.
Source record 10148741 at NHTSANHTSA communication ID: 10149751
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2017 Fusion Energi and C-Max Energi vehicles may exhibit an illuminated MIL with DTC P0C27 and/or P0C28. Follow the Service Procedure steps to correct the condition.
Source components: ELECTRICAL SYSTEM.
Source record 10149751 at NHTSANHTSA communication ID: 10144947
NHTSA source summary · Original PDF not reviewed by Recallfolio
When connecting the Vehicle Communication Module (VCM) and Integrated Diagnostic System (IDS) or Ford Diagnosis and Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic trouble codes (DTCs), no start, no crank conditions or the IPC inoperative. If a vehicle displays these issues, disconnect the equipment from the DLC and disconnect the vehicle battery. Wait 10 minutes and reinstall with the ignition off. Clear any DTCs present and retest.
Source components: STEERING.
Source record 10144947 at NHTSANHTSA communication ID: 10144919
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2018 Escape vehicles equipped with 1.5L/1.6L/2.0L EcoBoost, 2013-2018 Fusion vehicles equipped with 2.0L/2.7L EcoBoost, 2013-2018 MKZ vehicles equipped with 2.0L EcoBoost, 2017-18 MKZ vehicles equipped with 3.0L EcoBoost, 2015-2018 MKC vehicles equipped with 2.0L/2.3L EcoBoost, 2015-2018 Edge vehicles equipped with 2.0L/2.7L EcoBoost, 2016-2018 MKX vehicles equipped with 2.0L and 2.7L EcoBoost, 2016-2018 Explorer vehicles equipped with 2.3L EcoBoost, 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost and 2016-2018 Focus RS equipped with 2.3L EcoBoost may exhibit a dark black fluid leak from the right side transfer case intermediate shaft seal. Follow the Service Procedure to correct the condition.
Source components: ENGINE.
Source record 10144919 at NHTSANHTSA communication ID: 10144937
NHTSA source summary · Original PDF not reviewed by Recallfolio
2015-2018 Edge, Fusion, Focus, MKZ, MKC, Escape vehicles equipped with a 2.0L EcoBoost engine may exhibit coolant consumption, white smoke and/or a runs rough condition. Refer to the extended coolant pressure test and checking for combustion gases in Workshop Manual (WSM), Section 303-03A. If internal coolant loss is confirmed, further investigation of the head gasket interface is required. Carefully inspect the cylinder block and head for erosion, pitting, and flatness defects, primarily between the cylinder to cylinder bore bridges. If defects to the aluminum surface on the cylinder block and/or cylinder head are found, follow the cost cap tool for component replacement. Follow WSM, Section 303-01A for the repair procedures
Source components: ENGINE AND ENGINE COOLING.
Source record 10144937 at NHTSANHTSA communication ID: 10144930
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2018 Ford and Lincoln vehicles equipped with SYNC 3 not at the latest software level may exhibit Various Performance Related concerns such as Display Operation, Navigation, Voice Recognition, Phone Pairing, Applink, Travel Link, Slow System Response, etc. Check for SYNC software update under the OASIS Tab SYNC selection. If an update is available refer to WSM, Section 415-00 and update the APIM software. After Installation, complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
Source components: ELECTRICAL SYSTEM.
Source record 10144930 at NHTSANHTSA communication ID: 10143102
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various 2016-2018 vehicles with SYNC 3 may experience a touch screen that does not respond to any input. Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
Source components: ELECTRICAL SYSTEM · EQUIPMENT.
Source record 10143102 at NHTSANHTSA communication ID: 10137115
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 Fusion/MKZ/MKC/Escape/Edge vehicles equipped with a 2.0L EcoBoost engine may exhibit a runs rough condition with DTCs P0300, P0301, P0302, P0303, P0304 and/or P0316. This may be due to coolant intrusion due to corrosion on the engine block. To diagnose this concern, with the engine at normal operating temperature, pressurize the cooling system to 138 kPa (20 psi) and hold for 5 hours. If the coolant pressure drops 27.57 kPa (4psi), remove the spark plugs and inspect for coolant in the cylinders. If coolant is found in any of the cylinders, replace the engine long block assembly. Follow normal prior approval process for your Dealership. However, follow the diagnostic repair procedure in this article to determine correct repair. For claiming, use causal part 6006 and applicable labor operations in Section 6 of the SLTS Manual.
Source components: ENGINE AND ENGINE COOLING.
Source record 10137115 at NHTSANHTSA communication ID: 10137113
NHTSA source summary · Original PDF not reviewed by Recallfolio
Replacing the original equipment SYNC/Navigation system with either an aftermarket SYNC/Navigation kit or modifying original SYNC/Navigation parts to provide additional features is not recommended nor supported on any Ford, Mercury or Lincoln vehicle. Only approved Genuine Ford accessories or originally installed systems are supported and certified to function correctly with other vehicle systems. If you suspect a system has been modified, the following resources can be used to verify original equipment: Monroney Label (Window Sticker), Professional Technician Society (PTS) OASIS tab select SYNC or HVBOM. For Genuine Ford accessories use: PTS Workshop Tab select Dealer Installed Accessory or Accessory Installation.
Source components: EQUIPMENT.
Source record 10137113 at NHTSANHTSA communication ID: 10137110
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2017 Fusion Energi, 2012-2017 Focus Electric and 2013-2017 C-MAX Energi vehicles equipped with a TCU built on or before 11-Oct-2017 may exhibit a discharged battery, inoperative remote features via MyFord Mobile app, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 with no modem electronic serial number (ESN) displayed. To correct this condition, perform any open TCU field service actions (FSAs). If U0198 DTC still remains, remove the TCU fuse for 5 minutes then reinstall. Reprogram the TCU using IDS or Ford J2534 Diagnostic Software (FJDS) release 108.05 or higher. An internet connection is required. Calibration files may also be obtained at www.motorcraftservice.com. For claiming, use causal part 14G229 and applicable labor operations in section 10 of the SLTS manual
Source components: ELECTRICAL SYSTEM.
Source record 10137110 at NHTSANHTSA communication ID: 10137100
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various 2016-2017 vehicles with SYNC 3 may experience a touch screen that does not respond to any input. Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
Source components: ELECTRICAL SYSTEM.
Source record 10137100 at NHTSANHTSA communication ID: 10137097
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2012-2017 Focus BEV, 2013-2016 Fusion Energi And 2013-2017 CMAX Energi vehicles equipped with a Telematics Control Unit (TCU) may exhibit inoperative remote features via My Ford Mobile app, discharged battery, incomplete user authorization and/or diagnostic trouble code (DTC) U0198 with no modem electronic serial number (ESN) displayed. To correct this condition, perform any open TCU field service actions (FSAs). If DTC U0198 remains, remove the TCU fuse for 5 minutes then reinstall prior to programming. Perform IDS Network Test and reprogram the TCU using Integrated Diagnostic System (IDS) release 108.05 or higher. An internet connection is required. Calibration files may also be obtained at www.motorcraftservice.com. For claiming, use causal part 14G229 and applicable labor operations in section 10 of the SLTS manual.
Source components: ELECTRICAL SYSTEM.
Source record 10137097 at NHTSANHTSA communication ID: 10137085
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2012-2018 Focus Electric, 2013-2017 C-Max Energi, and 2013-2018 Fusion Energi plug-in hybrid electric vehicles (PHEV) may exhibit the high voltage (HV) battery failing to charge while connected to the Delphi 120 volt electric vehicle service equipment (EVSE) charge cord. To identify a Delphi EVSE the coupler on the EVSE that connects to the vehicle charge port is solid black. For information on the Delphi EVSE indicator status used for diagnostics, reference High Voltage Battery > Charging the High Voltage Battery in the Owners Guide for a 2018 Fusion Energi. Reference the Convenience Cord Light Emitting Diode (LED) Indicators chart. The Workshop Manual (WSM) is scheduled to be revised at a later date.
Source components: ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL.
Source record 10137085 at NHTSANHTSA communication ID: 10137084
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2017 C-MAX Energi, 2013-2018 Fusion Energi, 2013-2018 C-MAX/Fusion Hybrid/MKZ Hybrid may exhibit a no start with battery energy control module (BECM) diagnostic trouble code (DTC) P0AE5. For 2015-2017 C-MAX Energi refer to the 2014 MY C-MAX Workshop Manual (WSM), Section 414-03A for normal diagnostics. For all vehicles, if WSM pinpoint testing for BECM DTC P0AE5 finds the DC/DC converter control module (14B227), cabin coolant heater (18K463) or A/C compressor (19703) has low high voltage circuit internal resistance, only replace the component found with low internal resistance. It is not necessary to replace the high voltage battery junction (10C666) along with the low resistance high voltage component. The WSM is currently under revision.
Source components: ELECTRICAL SYSTEM.
Source record 10137084 at NHTSANHTSA communication ID: 10136597
NHTSA source summary · Original PDF not reviewed by Recallfolio
2010-2018 various vehicles equipped with SYNC or SYNC 3 may not function when attempting to find or use the Spotify app via AppLink. As of an update released on 1/15/2018 Spotify will no longer be supporting their AppLink integration. No repair attempts should be attempted to correct this concern.
Source components: EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
Source record 10136597 at NHTSANHTSA communication ID: 10136592
NHTSA source summary · Original PDF not reviewed by Recallfolio
When connecting the Vehicle Communication Module (VCM) and Integrated Diagnostic System (IDS) or Ford Diagnosis and Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic trouble codes (DTCs), no start or no crank conditions or the IPC inoperative. For Lincoln vehicles, this information is now listed in the Technical Inspection and Post Road Test Sections of ePDI on the PTS website. If a vehicle displays these issues, disconnect the equipment from the DLC and disconnect the vehicle battery. Wait 10 minutes and reinstall with the ignition off. Clear any DTCs present and retest.
Source components: ELECTRICAL SYSTEM:12V/24V/48V BATTERY.
Source record 10136592 at NHTSANHTSA communication ID: 10140332
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various 2016-2017 vehicles with SYNC 3 may experience a touch screen that does not respond to any input. Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:SOFTWARE · EQUIPMENT · EQUIPMENT:ELECTRICAL.
Source record 10140332 at NHTSANHTSA communication ID: 10138533
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various 2016-2017 vehicles with SYNC 3 may experience a touch screen that does not respond to any input. Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
Source components: EQUIPMENT:ELECTRICAL.
Source record 10138533 at NHTSANHTSA communication ID: 10140323
NHTSA source summary · Original PDF not reviewed by Recallfolio
The Accessory (Wireless) Keyless Entry Keypad can only be used with vehicles that are factory built with Remote Keyless Entry (RKE). The master code for the Accessory (Wireless) Keyless Entry Keypad can be retrieved from FMCDealer - Parts and Service - Parts Product Line Information - Keys/Entry Devices - Aftermarket Keyless Entry Keypad Code Access. Access to this site is granted through Dealer Program Enrollment System (DPES) and Dealer Principal, General Manager or Parts and Service Director can authorize users. Once authorized the retrieval process for master code can be obtained. The master code for the Accessory Keyless Entry Keypad cannot be retrieved from the body control module(BCM) with a diagnostic tool.
Source components: EQUIPMENT · EQUIPMENT:ELECTRICAL.
Source record 10140323 at NHTSANHTSA communication ID: 10138524
NHTSA source summary · Original PDF not reviewed by Recallfolio
The Accessory (Wireless) Keyless Entry Keypad can only be used with vehicles that are factory built with Remote Keyless Entry (RKE). The master code for the Accessory (Wireless) Keyless Entry Keypad can be retrieved from FMCDealer - Parts and Service - Parts Product Line Information - Keys/Entry Devices - Aftermarket Keyless Entry Keypad Code Access. Access to this site is granted through Dealer Program Enrollment System (DPES) and Dealer Principal, General Manager or Parts and Service Director can authorize users. Once authorized the retrieval process for master code can be obtained. The master code for the Accessory Keyless Entry Keypad cannot be retrieved from the body control module(BCM) with a diagnostic tool.
Source components: EQUIPMENT:ELECTRICAL.
Source record 10138524 at NHTSANHTSA communication ID: 10140315
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2018 Escape/Fusion/MKZ vehicles equipped with 2.5L or 1.5L/2.0L/3.0L Ecoboost engine, 2015-2018 MKC/Edge/Explorer vehicles equipped with 2.0L/2.3L/2.7L EcoBoost engine, 2016-2018 MKX vehicles equipped with 2.7L Ecoboost engine, 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost, and AWD may exhibit a fluid leak from the PTU intermediate shaft seal. Replacement of the intermediate shaft seal seal does not require removal of the PTU and does not require the use of the cover seal and bolt kit (CV6Z-7275-K) to perform the repair. Refer to the Workshop Manual (WSM), Section 308-07.
Source components: ENGINE · POWER TRAIN:TRANSFER CASE (4-WHEEL DRIVE).
Source record 10140315 at NHTSANHTSA communication ID: 10138516
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2018 Escape/Fusion/MKZ vehicles equipped with 2.5L or 1.5L/2.0L/3.0L Ecoboost engine, 2015-2018 MKC/Edge/Explorer vehicles equipped with 2.0L/2.3L/2.7L EcoBoost engine, 2016-2018 MKX vehicles equipped with 2.7L Ecoboost engine, 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost, and AWD may exhibit a fluid leak from the PTU intermediate shaft seal. Replacement of the intermediate shaft seal seal does not require removal of the PTU and does not require the use of the cover seal and bolt kit (CV6Z-7275-K) to perform the repair. Refer to the Workshop Manual (WSM), Section 308-07.
Source components: ENGINE AND ENGINE COOLING.
Source record 10138516 at NHTSA