2016 Ford
F-250 SDProblems & recalls

Some 2013-2016 Super Duty vehicles equipped with a 6.7L diesel engine and 2015-2019 Transit vehicles equipped with a 3.2L diesel engine may not pass a state smog test due to the exhaust gas system (EGS) monitor that will not run after completing the exhaust gas sensor drive cycle located within Section 2 of the Powertrain Control/Emissions Diagnostics (PC/ED) Manual > Drive Cycles. This may be due to the vehicles diesel oxidation catalyst (DOC) age counter being under the 120-minute age requirement. There is an all-new "PCM  Catalytic Converter Age Evaluation" application within the latest version of the Ford Diagnosis and Repair System (FDRS). Use this new FDRS application to determine the age (in minutes) of the DOC. If the age is less than 120 minutes, perform manual regenerations to increase the catalyst age counter to satisfy the monitor age requirement. If further assistance is needed, contact the technical assistance center (TAC). Note: this article only applies to the EGS monitor. Problems with other vehicle monitors not running successfully must be addressed using normal diagnostics located i

Components: ENGINE · POWER TRAIN · UNKNOWN OR OTHER. Confirm detailed applicability in the original document.

Customer Satisfaction Program 25N15 - Supplement #1 Certain 2015-2019 Model Year Multiple Vehicle Lines Rear View Camera Inspection For One-Time Replacement

Components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER. Confirm detailed applicability in the original document.

Some 2013-2016 Super Duty vehicles equipped with a 6.7L diesel engine and 2015-2019 Transit vehicles equipped with a 3.2L diesel engine may not pass a state smog test due to the exhaust gas system (EGS) monitor that will not run after completing the Exhaust Gas Sensor drive cycle located within Section 2 of the Powertrain Control/Emissions Diagnostics (PC/ED) Manual > Drive Cycles. This may be due to the vehicles diesel oxidation catalyst (DOC) age counter being under the 120-minute requirement. Engineering is investigating this issue and working on a solution.

Components: ENGINE. Confirm detailed applicability in the original document.

Ford and Lincoln vehicles equipped with wired keyless entry keypad systems and accessory wireless keyless entry keypad systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k

Components: ELECTRICAL SYSTEM · STRUCTURE:BODY · UNKNOWN OR OTHER. Confirm detailed applicability in the original document.

This article supersedes TSB 24-2165 to update the TSB Service Procedure. Some vehicles listed in the Model statement above may exhibit various SYNC performance related concerns including but not limited to:  Display operation concerns  Navigation inoperative  Voice recognition concerns  Phone connection issues  Dropped phone connections  Applink related performance  Travel Link not present or showing incorrect traffic  Slow system response NOTE: Ford has found some of the APIMs replaced and returned for inspection contained an outdated software level and the APIM did not require replacement. The customer concern may have been resolved by updating the APIM with latest level of software. The SYNC 3 universal thumb drive will be able to update the APIM software without the use of a scan tool and does not require the process to be monitored. Ford will be monitoring APIM replacements to confirm TSB directed software updates have been performed.

Components: ELECTRICAL SYSTEM. Confirm detailed applicability in the original document.

Certain 2011-2022 Model Year Super Duty Vehicles Equipped with 6.7L Engine - Emission Control Information Label Update for Qualified Vehicles

Components: ENGINE · UNKNOWN OR OTHER. Confirm detailed applicability in the original document.

While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions. While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions.

Components: UNKNOWN OR OTHER. Confirm detailed applicability in the original document.

All accessory stick-on keyless entry keypads come with a wallet card containing the master code. If the accessory keypad was factory installed, this card will be placed in the glove box and should be handed to the vehicles owner during initial delivery. Unlike the integrated (wired) factory keypad, the accessory keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool. If the wallet card for an accessory keypad is lost, follow these steps to recover the code. Dealer Key Code access is granted through the Dealer Program Enrollment System (DPES); dealership management can authorize users. The authorized user must go to FMCDealer.com > Parts and Service > Parts Product Line Information > Keys/Entry Devices > Aftermarket Keyless Entry Keypad Code Access. Follow the instructions on the screen to obtain the master code for the accessory keypad.

Components: EQUIPMENT. Confirm detailed applicability in the original document.

This article supersedes TSB 22-2201 to update the Service Procedure and Parts List. Some 2015-2019 F-Super Duty and 2016-2019 F-650/F-750 vehicles equipped with a 6.7L engine may exhibit an oil leak from the oil filter, crankcase vent oil separator, oil cooler, or upper/lower oil pan. This may be due to the mating surfaces of the upper oil pan and the engine block or to a clogged crankcase vent oil separator.

Components: ENGINE AND ENGINE COOLING. Confirm detailed applicability in the original document.

2024 F-Super Duty vehicles are equipped with XL-22 (WSS-M2C184-A1) high temperature power steering fluid that looks like clear hydraulic fluid. This fluid is an improvement in high temperature and thermal oxidative stability compared to Mercon LV. This power steering fluid is also compatible and highly recommended to use when filling or topping off power steering systems of all 2012-2023 F-Super Duty vehicles originally equipped with Mercon LV.

Components: STEERING. Confirm detailed applicability in the original document.

Some 2015-2019 F-Super Duty and 2015-2020 F-150/Mustang vehicles may require replacement of the powertrain control module (PCM) for various reasons. While performing a programmable module installation (PMI) using the Integrated Diagnostic Service (IDS) scan tool, an error message may state: Configuration Failed, Would You Like To Retry? This may be due to improper module replacement steps. Make sure that the original module is installed in the vehicle, delete the vehicle session, then start a new vehicle session. Once the session starts, run the PCM PMI and install the new PCM only when the scan tool instructs. Finish the PMI by following the prompts given by IDS. If the original PCM is not available, it is possible to configure the module by running as-built programming on the PCM. When IDS asks to obtain part numbers or configuration data, select configuration data.

Components: ELECTRICAL SYSTEM · EQUIPMENT. Confirm detailed applicability in the original document.

Various 2013-2019 vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P264F after powertrain control module (PCM) replacement. This DTC indicates that the engine serial number (ESN) must be programmed into the PCM. The ESN is located on PTS > Diagnostics tab > HVBoM > Features > Engine Serial Number. Once the ESN is obtained from the historical vehicle bill of materials (HvBOM), it can be programmed into the PCM using the appropriate Ford diagnostic scan tool. Navigate to the toolbox tab> powertrain menu> Service Functions> ESN.

Components: POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM) · POWER TRAIN:MANUAL TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Confirm detailed applicability in the original document.