2022 Ford F-150 Manufacturer communications & TSBs.Page 3
Original record summaries, dates and identifiers for this model-year. Records 201–300 of 474, ordered newest first. Dated records on this page: Aug 2, 2023–Jul 23, 2024.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Jul 23, 2024Service Bulletin/Repair Instructions
SSM 52738
NHTSA communication ID: 11005837
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2024 Bronco/F-150 (non-Lightning) vehicles may exhibit a "Check Charging System" message in the instrument panel cluster (IPC) while the charging system is fully operational and there are no diagnostic trouble codes (DTC) stored related to the charging system. This may be due to the customer using an aftermarket programmer to change body control module (BCM) configuration.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 F-150 vehicles and 2024 F-150 Lightning vehicles may exhibit modules on the high-speed controller area network 2 (HS-CAN2), high-speed controller area network 3 (HS-CAN3), high-speed controller area network 4 (HS-CAN4) and/or the medium-speed controller area networks (MS-CAN) not responding to the Ford Diagnosis and Repair System (FDRS) and the modules on these networks fail the network test without any diagnostic trouble codes (DTCs) tied to the affected modules. The modules on the flexible data rate controller area network 2 (FD-CAN1) and the high-speed controller area network 1 (HS-CAN1) will communicate with the FDRS. Vehicles equipped with a power opening/closing tailgate may also exhibit an intermittent inoperative power tailgate. This may be due to the gateway module A (GWM) not being configured properly. To correct this condition, download and run the GWM - Gateway Module A (GWM) Configuration application using the latest version of the FDRS. For claiming, use causal part number 14G490 and applicable labor times from Section 10 of the Service Labor Times Standard (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 24-2168 to address revised software for 2022-2023 HVAC modules. Some 2021-2023 F-150 vehicles equipped with a gasoline, hybrid or flex fuel engine (non-Lightning, non-diesel) may exhibit inoperative A/C, lack of air flow, and/or evidence of the evaporator freezing. This may be due to the software level of the PCM and heating, ventilation and air conditioning (HVAC) module. To correct this condition, follow the Service Procedure to reprogram the PCM and HVAC module to the latest software level via the Ford Diagnosis and Repair System (FDRS)
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2024 F-150/Bronco and 2023-2024 Escape/F-Super Duty vehicles built with SYNC 4 require a connected phone with Android Auto or Apple CarPlay active to enable voice interactions and use of the steering wheel voice control button. This is due to the affected vehicles not having built in voice interactions capability. Vehicles with built in voice interaction capability can be identified as also being equipped with the built in connected navigation feature which includes a navigation tab on the center display screen. Diagnostics should only be performed for voice interactions on vehicles equipped with built in voice interaction capability or with Android Auto or Apple CarPlay active.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2024 F-150 non-Raptor vehicles equipped with 4WD and ESOF transfer case (minor feature code FMLAS) may exhibit an intermittent grinding/hum/rumble noise from the front wheel area while in 2WD that goes away when the vehicle is put into 4WD. These vehicles will also have no diagnostic trouble codes (DTCs) stored in the transfer case control module (TCCM). To confirm a vehicle is built with a certain minor feature code, review the build information by double-clicking the vehicle identification number (VIN) in the upper left corner in the Professional Technician System (PTS). This may be due to incomplete disengagement of the integrated wheel end (IWE) actuator assemblies. To correct this condition, follow the Service Procedure to replace IWE actuator assemblies
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2024 Escape/Corsair, 2021-2024 Bronco Sport/F-150, and 2022-2024 Maverick vehicles may exhibit a condition where the door(s) do not open using the exterior door handle(s). This may be due to an enabled door reinforcement inertia lock within the exterior door handle. This condition occurs when the doors are closed or opened with excessive force. To correct this condition, follow the door reinforcement inertia lock rest procedure that has been added to Section 501-14 of the Workshop Manual under General Procedures. For claiming, use causal part 78219A64.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2024 F-150 and 2023-2024 Expedition/Navigator vehicles equipped with a 3.5L EcoBoost engine may exhibit a rattle/scraping noise from the bellhousing area on start-up. This may be due to the torque converter studs contacting the engine-to-transmission spacer plate (separator plate). To correct this condition, remove the transmission and flexplate and inspect the engine-to-transmission spacer plate and torque converter studs for wear/damage. If wear/damage is found, replace the engine-to-transmission spacer plate. Refer to Workshop Manual (WSM) Section 303-01 Engine - 3.5L EcoBoost (BM), Removal and Installation, Crankshaft Rear Seal. When reinstalling the starter motor, make sure the starter is flush with the engine-to-transmission spacer plate prior to tightening the studbolts. Failure to do so may result in damaging the newly installed engine-to-transmission spacer plate.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2024 F-150 non-Lightning vehicles may exhibit turn signal indicators on the instrument panel cluster (IPC) flashing fast when activated after running the IPC - Towbar Configuration application using the Ford Diagnosis and Repair System (FDRS) scan tool without any exterior turn signals being inoperative. The exterior turn signals will function normally. The IPC - Towbar Configuration application has recently been updated to correct this issue. To correct this condition, download and rerun the latest version of the IPC - Towbar Configuration application using the latest software level of the FDRS scan tool.
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 21-2126 to address the revised software and include affected 2023 3.3L vehicles. Some 2021-2023 F-150 vehicles equipped with a gasoline, hybrid or flex fuel engine (non-Lightning) may exhibit inoperative A/C, lack of air flow, and/or evidence of the evaporator freezing. This may be due to the software level of the PCM and heating, ventilation and air conditioning (HVAC) module. To correct this condition, follow the Service Procedure to reprogram the PCM and HVAC module to the latest software level via the Ford Diagnosis and Repair System (FDRS).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSBs 24-2100 and 24-2070 to add 2023 F-150 vehicles, update the TSB Issue statement and the TSB Service Procedure. Some 2021-2023 F-150, 2022-2023 Expedition/Navigator/Mustang and 2020-2023 Transit/Explorer/Aviator vehicles equipped with a 10R80/10R80MHT transmission may exhibit a harsh/delayed engagement and/or harsh/delayed shift, an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to the software in the powertrain control module (PCM) or transmission control module (TCM), the transmission solenoid ID strategy, sticking valves in the main control valve body and/or axial movement of the CDF clutch cylinder (7H351) sleeve. To correct the condition, follow the Service Procedure to identify and correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles equipped with SYNC4 may exhibit one or more of the following symptoms after all currently available accessory protocol interface module (APIM) software updates have been performed. - General system performance, stability, and intermittent system reboots. - Intermittent Wireless CarPlay or Android Auto function. - Phone related concerns with intermittent No Audio or Static. - Navigation/global positioning system (GPS) related concerns through CarPlay and Android Auto. - Alexa function consistency and stability. These symptoms may be due to the software in the APIM. Replacing the APIM will not resolve these symptoms for the customer. Before returning the vehicle to the customer, review the procedures within Workshop Manual, Section 415-00 and ensure the latest APIM software is installed. Refer to General Service Bulletin (GSB) 23-7146 for help determining the latest available level of software. IMPORTANT: some module software updates will only display as available on Ford Diagnosis and Repair System (FDRS) after prerequisite modules are updated. This may require the technician to update certain modules multiple times during the service visit, before the latest APIM software is accessible in FDRS. If symptoms continue after latest APIM software has been installed, inform customers that Ford is working on additional software enhancements which are expected to be delivered over-the-air (OTA) by Q4 2024 on F-150, F-150 Lightning, Mustang Mach-E, Mustang, Escape, Corsair, Expedition, Navigator, Bronco, Mustang, and 2023-2024 F-Super Duty. Software will update automatically if vehicle connectivity is enabled in the vehicle's settings. For all other vehicles with SYNC4, schedule a service visit for customers in October 2024, when the updated APIM software is expected to be available to dealers. Monitor OASIS for additional information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 24-2054 to add 2024 models and update the production fix date. Some 2022-2024 F-150 vehicles built on 23-Aug-2022 and through 29-Mar-2024 equipped with a 5.0L engine may exhibit an oil leak from the oil filter adaptor to engine block mounting area. This may be due to block porosity just below the oil filter adapter near the main bearing cap outer bolt. To correct the condition, follow the Service Procedure to inspect the engine block for a porosity leak.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various vehicles equiped with 10R80/10R80 MHT/10R100/10R140 transmissions may require replacement of the seal kits (7153) when internal repairs are being performed. These kits come with 4 wheel drive (4WD) seals and will no longer include the 2WD seals. When working on a 2WD vehicle, any 2WD seals must be ordered separately. Refer to the parts catalog for the proper 2WD seals required.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2024 F-150-3.5L FHEV, 2020-2024 Explorer 3.3L FHEV, 2020-2024 Escape 2.5L FHEV, and 2022-2024 Maverick 2.5L FHEV vehicles may exhibit an illuminated MIL with DTC P237F and/or P2C23 stored in the powertrain control module (PCM) and no affect on drivability. This may be due to seal damage, corrosion and/or water intrusion in the exhaust coolant temperature (ECT) sensors 3 and/or 4 connector. Visual inspection should be completed on ECT3 and ECT4 sensors and mating connections for seal damage, water intrusion, and corrosion. If seal damage, water intrusion or corrosion is present, repair per cell 5 of the Wiring Diagram, then apply Motorcraft® XG-12 Electrical Grease to the female/vehicle side of the harness. This inspection of ECT3 and ECT4 sensors should be completed prior to starting the appropriate pinpoint test in Section 303-03 of the Workshop Manual (WSM). If DTCs P237F and/or P2C23 do not return, no further action is necessary and the replacement of the entire exhaust heat exchanger assembly is not required. If P237F and/or P2C23 returns, follow the pinpoint test in Section 303-03 of the WSM for further diagnostics.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2022-2023 F-150 Lightning vehicles require installation of a cold plate when replacing a HV battery module. Workshop Manual (WSM) Section 414-03A, removal and installation, has been updated with improved diagnostics and direction for HV battery module replacement. If the parts catalog note states that a cold plate must also be ordered for the HV battery module(s) that are needing replaced, the called out corelating cold plate is required for repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 24-2093 to address the revised software and include affected 3.5L FHEV vehicles. Some 2021-2023 F-150 vehicles equipped with a gasoline, hybrid or flex fuel engine (non-Lightning) except 2023 F-150 with 3.3L may exhibit inoperative A/C, lack of air flow, blows warm, and/or evidence of the evaporator freezing. This may be due to the software level of the PCM and heating, ventilation and air conditioning (HVAC) module.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 23-2425 to address revised software and update the Parts List. Some 2022-2023 F-150 hybrid vehicles equipped with a 3.5L PowerBoost engine may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0420 and/or P0430 stored in the powertrain control module (PCM). This may be due to calibration and controls sensitivity. To correct the condition, follow the Service Procedure to reprogram the PCM and perform the catalyst stabilization drive cycle.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 23-2276 to update the Title, Issue Statement, and Action Statement to clarify the vehicle applications. Some 2021-2023 F-150 vehicles equipped with a 2 kilowatt (kW) (not 400 watt (W)) direct current/alternating current converter module A (DCACA) inverter (minor feature code HUKAK) may exhibit an illuminated tire pressure monitoring system (TPMS) indicator with diagnostic trouble code (DTC) B124D:02 stored in the BCM. This may be due to the DCACA inverter causing radio frequency interference (RFI). To confirm a vehicle is built with a certain minor feature code, review the build information by double-clicking the vehicle identification number (VIN) in the upper left corner in the Professional Technician System (PTS).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2019 Explorer and 2018-2024 Transit/F-150/Expedition/Navigator vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0627, P025A, P025B, P00C6, P008A and/or U0109 stored in the powertrain control module (PCM). Diagnosis should include checking for an intermittent or partial disconnect of the harness to the fuel pump control module (FPCM) connector, connector pin push-outs, damaged pins/terminals, or loose/corroded grounds. Confirm FPCM connector (Explorer - C3239, Transit - C433, F-150 - C460/C4336, Expedition/Navigator - C433/C4033) is fully seated and inspect applicable grounds (Explorer G302, Transit - G401, F-150 - G401, Expedition/Navigator - G403/G406) prior to performing guided diagnostics or replacing any components.
NHTSA source summary · Original PDF not reviewed by Recallfolio
All accessory stick-on keyless entry keypads come with a wallet card containing the master code. If the accessory keypad was factory installed, this card will be placed in the glove box and should be handed to the vehicles owner during initial delivery. Unlike the integrated (wired) factory keypad, the accessory keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool. If the wallet card for an accessory keypad is lost, follow these steps to recover the code. Dealer Key Code access is granted through the Dealer Program Enrollment System (DPES); dealership management can authorize users. The authorized user must go to FMCDealer.com > Parts and Service > Parts Product Line Information > Keys/Entry Devices > Aftermarket Keyless Entry Keypad Code Access. Follow the instructions on the screen to obtain the master code for the accessory keypad.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2024 F-150 vehicles may exhibit a side door ajar and/or a hood ajar warning message displayed in the instrument panel cluster (IPC) with or without diagnostic trouble codes (DTC) P166B, B1175, B1176, B11C1 and/or B11C0. This may be due to a misalignment of the the door or hood and/or their strikers. Before attempting any component diagnosis or replacement, check the door and/or hood and their strikers for proper alignment. Refer to Workshop Manual (WSM), Section 501-03 alignment procedures. If the doors and hood are properly aligned, continue with normal diagnostics.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 F-150 vehicles may exhibit DTCs B1D08 And/Or B1D09 stored in the trailer module (TRM) with a Trailer Brake System Fault See Manual message in the instrument panel cluster (IPC) when a trailer is not connected to the vehicle. This may be due to water intrusion at the back side of the trailer tow connector. Disconnect connector C4099 from the back of the trailer tow connector (14489). Inspect connector C4099 and the mating socket on the back of the trailer tow connector for signs of corrosion or damage. If corrosion or damage is present at either connector, replace both the female side of the C4099 connector using service pig tail kit (3U2Z-14S411-JXC) and the trailer tow connector. If corrosion or damage is not present, refer to the Workshop Manual (WSM) Section 417-01 Exterior Lighting, Diagnosis and Testing for additional diagnosis. For claiming, use causal part 13A576 and applicable labor operations in Section 01 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2024 F-150 and 2021-2024 Bronco vehicles equipped with a 2.7L or 3.0L EcoBoost engine may exhibit a ticking/tapping or rattle type noise from the top front cover area of the engine on initial start-up after a cold soak of 6 hours or more that may last for 2-5 seconds. This may be due to a stuck internal component of the variable cam timing (VCT) unit. To correct the condition, replace all 4 of the VCT units following Workshop Manual (WSM), Section 303-01. For claiming, use causal part 6C525 and applicable labor operations in Section 6 of the Service Labor Time Standards (SLTS) Manual. If labor times are not available, claim M-time.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various vehicles have had pinpoint tests, guided routines and the Warranty and Policy Manual recentlyupdated for diagnostics and repairs on SYNC generation 3 and later applications. When performingdiagnostics and repairs on SYNC Gen 3 or later, select the diagnostics tab and search for related symptoms,DTCs and keywords. The search results will be shown in the search results pane. Read and follow allTechnical Service Bulletins (TSB), Special Service Message (SSM)s or General Service Bulletin (GSB) first if abulletin specifically addresses the vehicle concern. If there are no messages, run the appropriate diagnosticpinpoint test found in the Workshop Manual (WSM). Follow the steps in the pinpoint test. Make sure to note thetitle of the guided routine, using the correct one for the vehicle's symptom or diagnostic trouble code (DTC) iscritical. Depending on the outcome of the pinpoint test, a repair validation code (RVC) may be generated eitherin the pinpoint test or Guided Routine. If the vehicle concern still exists after following the pinpoint tests orguided routine, then a manual RVC can be generated using the RVC Assist Form. A manual RVC can only begenerated once the above process has been followed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 24-2059 to update the Service Procedure LTIS statement. Some 2021-2022 F-150, 2022-2023 Expedition/Navigator/Mustang and 2020-2023 Transit/Explorer/Aviator vehicles equipped with a 10R80/10R80MHT transmission may exhibit a harsh/delayed engagement and/or harsh/delayed shift, an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) that are stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to the software in the powertrain control module (PCM) or transmission control module (TCM), the transmission solenoid ID strategy, sticking valves in the main control valve body and/or axial movement of the CDF clutch cylinder (7H351) sleeve.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 F-150 non-Lightning vehicles may exhibit an illuminated powertrain malfunction (wrench) indicator and Service Vehicle Soon message in the instrument panel cluster (IPC) with diagnostic trouble code (DTC) U031D in the powertrain control module (PCM) and no other drivability concerns. This may be due to the configuration of the PCM.
Source components: ELECTRICAL SYSTEM · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM) · POWER TRAIN:MANUAL TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 F-150 vehicles equipped with a gasoline or flex fuel engine (non-Lightning/non-PowerBoost) may exhibit inoperative A/C, lack of air flow, blows warm, and/or evidence of the evaporator freezing. This may be due to the software level of the PCM and heating, ventilation and air conditioning (HVAC) module.
Source components: ELECTRICAL SYSTEM · VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022-2023 F-150 Tremor vehicles built on or before 18-May-2023 may experience the instrument panel cluster (IPC) goes blank or reboots after attempting to access Trailer Tire Info in the Towing menu. This may be due to the software in the IPC
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 F-150 non-Lightning vehicles may exhibit an illuminated powertrain malfunction (wrench) indicator and Service Vehicle Soon message in the instrument panel cluster (IPC) with diagnostic trouble code (DTC) U031D in the powertrain control module (PCM) and no other drivability concerns. This may be due to the configuration of the PCM. To correct this condition, run the PCM - Disable Pro Trailer Hitch Assist application using the latest software level of the Ford Diagnosis and Repair System (FDRS) scan tool.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM) · POWER TRAIN:MANUAL TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 23-2351 to remove 2023 F-150 10R80 and 10R80 MHT vehicle applications. The 2023 F-150 10R80 and 10R80 MHT vehicles will be the subject of a separate article. Some 2021-2022 F-150, 2022-2023 Expedition/Navigator/Mustang and 2020-2023 Transit/Explorer/Aviator vehicles equipped with a 10R80/10R80MHT transmission may exhibit a harsh/delayed engagement and/or harsh/delayed shift, an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes that are stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to the software in the powertrain control module (PCM) or transmission control module (TCM), the transmission solenoid ID strategy, sticking valves in the main control valve body and/or axial movement of the CDF clutch cylinder (7H351) sleeve.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 F-150 vehicles may exhibit DTC C0604:00 stored in the powertrain control module (PCM) and may have an Active Air Dam System Fault See Manual message displayed in the instrument panel cluster (IPC). To correct this condition, clear and retest for the DTC C0604:00. If DTC C0604:00 returns, refer to Workshop Manual (WSM) Section 501-19 Bumpers, Diagnosis and Testing for additional diagnosis.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM) · POWER TRAIN:MANUAL TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Quality Improvements include: -Robustness action in operation of vehicle to detect low-state-of-charge battery and prevent engine stall, as well as provide improved warning to customers when low-state-of-charge conditions exist. -To prevent the potential incorrect On-board scales.
NHTSA source summary · Original PDF not reviewed by Recallfolio
For 2015-2024 Ford and Lincoln vehicles equipped with turbocharged engines and customer concern of an engine oil leak, refer to Workshop Manual (WSM), Section 303-00 for oil leak inspection and testing methods. Ford has evaluated turbochargers replaced for oil leak symptoms and although oil may collect on the external surface of a turbocharger, it is extremely rare for a turbocharger assembly to be the root cause of the oil leak. Careful inspection of the turbocharger oil feed and drain tubes should be performed along with the recommended WSM procedures as needed. Warranty claims for turbocharger replacement going forward will be assessed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2011-2024 Mustang and F-150 vehicles equipped with a 5.0L engine may exhibit a tick tap and/or typewriter ticking noise at idle after an engine oil change. It is often referred to as typewriter noise because of its similarity to the sound of a mechanical typewriter. The noise in question may be heard on some engines when engine temperatures reach 150°F (65°C) or higher and engine speed is at idle up to approximately 1700 RPM. It can typically be heard at the front wheel well and is often isolated to the transmission bell housing or oil pan area. The typewriter noise tick rate can be faster or slower and is not detrimental to the engine function or durability and has no short or long term effects on the engine. This an operating characteristic of the 5.0L engine and no repairs should be attempted. This information along with an example audio clip has been added to the WSM Section 303-00 Engine System General Information > Diagnosis and Testing > Engine > PPT F > Step F2.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Many body control module C (BCMC) warranty return parts are coming back with no trouble found. To verify that the BCMC is at fault prior to replacing, perform the following. First, disconnect the battery then check all BCMC connectors for terminal pushout, pin damage, spread terminals, and corrosion. Refer to Workshop Manual Section 100-00 Wire Terminal Inspection and Replacement. If none found, reconnect the BCMC and battery terminals then recheck functionality. If concern still exists, proceed with BCMC replacement.
Source components: ELECTRICAL SYSTEM:BODY CONTROL MODULE/BCM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2024 Bronco/F-150, 2023-2024 Escape/F-Super Duty vehicles equipped with SYNC 4 may experience a concern during accessory protocol interface module (APIM) programming where the vehicle's center display screen indicates USB Error. This may be due to a lack of memory space available to perform the APIM software update. If it is a memory concern, the Ford Diagnosis and Repair System (FDRS) will provide an option to delete the voice application. Re-enter the module programming and when prompted, do not select first option - SYNC Module (APIM) Software Update, select the second option - Delete Voice Application(s) From Module. Once deleted, run the SYNC Module (APIM) Software Update as directed, this will update the software and automatically reload the voice app. If the voice delete option is not available, continue with normal diagnostics in the Workshop Manual, Section 418.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 23-2194 to add Figure 1 and update the parts list. Some 2022-2023 F-150 vehicles built on 23-August-2022 and through 30-April-2023 equipped with a 5.0L engine may exhibit an oil leak from the oil filter adaptor to engine block mounting area. This may be due to block porosity just below the oil filter adapter near the main bearing cap outer bolt.
NHTSA source summary · Original PDF not reviewed by Recallfolio
During service and repair requiring removal and replacement of a crankshaft bolt and/or crankshaft damper, achieving proper torque of the crankshaft pulley bolt is critical. Incorrect torque may allow the bolt to loosen resulting in the timing gear breaking and engine damage. Replacement of the bolt is critical to the repair and accurately following the installation procedure in the Workshop Manual (WSM) Section, 303-01 is extremely important. The bolt torque procedure can be found in the crankshaft front seal removal and installation procedure or in the engine assembly procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 F-150 vehicles may exhibit DTCs B1D08:11 and/or B1D09:11 stored in the trailer module (TRM) with a Trailer Brake System Fault See Manual message in the instrument panel cluster (IPC) when a trailer is not connected to the vehicle. This may be due to water intrusion at the back side of the trailer tow connector. Inspect connector C4099 and the trailer tow connector (14489) for signs of corrosion or damage. If corrosion or damage is present at either connector, replace the female side of the C4099 connector using service pig tail kit (3U2Z-14S411-JXC) and the trailer tow connector. If corrosion or damage is not present, refer to the Workshop Manual (WSM) Section 417-01 Exterior Lighting, Diagnosis and Testing for additional diagnosis. For claiming, use causal part 14489 and applicable labor operations in Section 01 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 F-150 and 2023-2024 Expedition/Navigator vehicles equipped with a 3.5L EcoBoost engine may exhibit a rattle/scraping noise from the bellhousing area on start-up. This may be due to the torque converter studs contacting the engine-to-transmission spacer plate (separator plate). To correct this condition, remove the transmission and flexplate and inspect the engine-to-transmission spacer plate and torque converter studs for wear/damage. If wear/damage is found, replace engine-to-transmission spacer plate. Refer to Workshop Manual (WSM) Section 303-01 Engine - 3.5L EcoBoost (BM), Removal and Installation, Crankshaft Rear Seal. When reinstalling the starter motor, be sure the starter is flush with the engine-to-transmission spacer plate prior to tightening the studbolts. Failure to do so may result in damaging newly installed engine-to-transmission spacer plate.
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 F-150 vehicles may exhibit DTCs B1D08:11 and/or B1D09:11 stored in the trailer module (TRM) with a Trailer Brake System Fault See Manual message in the instrument panel cluster (IPC) when a trailer is not connected to the vehicle. This may be due to water intrusion at the back side of the trailer tow connector. Inspect connector C4099 for signs of corrosion or damage. If corrosion or damage is present, replace the female side of the C4099 connector using service pig tail kit (3U2Z-14S411-JXC) and the trailer tow connector. If corrosion or damage is not present, refer to the Workshop Manual (WSM) Section 417-01 Exterior Lighting, Diagnosis and Testing for additional diagnosis. For claiming, use causal part 14489 and applicable labor operations in Section 01 of the Service Labor Time Standards (SLTS) Manual.
Source components: TRAILER HITCHES · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Software Update 24-PU0105-CMR-FX for 2022-2023 MY F-150 vehicles is now available. Quality Improvements include: - Robustness action to increase availability of BlueCruise
Source components: BACK OVER PREVENTION:SOFTWARE · ELECTRICAL SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 24-2020 to add minor feature code HUKAJ to the required vehicle criteria. Some 2021-2023 F-150 vehicles equipped with the minor feature code HUKAJ (400 watt direct current/alternating current (DC/AC) inverter system with a pickup bed alternating current (AC) power outlet socket) may experience the DC/AC inverter system inoperative with diagnostic trouble code (DTC) B1330:9A stored in the body control module (BCM). To confirm a vehicle is built with a certain minor feature code, review the build information by double-clicking the vehicle identification number (VIN) in the upper left corner in the Professional Technician System (PTS). This may be due to a connection issue at C4628
NHTSA source summary · Original PDF not reviewed by Recallfolio
Software Update PU1009-SS-NS for 2021-2023 MY F-150 vehicles is now available. Quality Improvements include: - Robustness action in operation of vehicle to detect low-state-of-charge battery and prevent engine stall, as well as provide improved warning to customers when low-state-of-charge conditions exist. - Eliminates potential Emergency Parking Brake activation when wire harness experiences a short. - Robustness action to prevent potential line pressure driftÃÂ DTC from setting. -Eliminate potential ABS Yaw Rate Calibration issue. -Robustness action to alleviate the Nuisance SSN (Stop Safely Now) message from setting and vehicle should operate as expected in the next Key Start event. -Eliminates potential Emergency Parking Brake activation when wire harness experience a short.
Source components: BACK OVER PREVENTION:SOFTWARE · ELECTRICAL SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Software Update 23-PU1113-UNX-DC for 2021-2023 MY F-150 vehicles is now available. Quality Improvements include - Restores TCU module DID vehicile specific configuration which were set to default values in previous OTA update.
Source components: BACK OVER PREVENTION:SOFTWARE · ELECTRICAL SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 F-150 vehicles may exhibit DTC U023A:08 after reprogramming the SCCM. Do not replace or reprogram the SCCM, image processing module A (IPMA) or their components for this condition at this time. This DTC does not alert the customer, will not affect vehicle durability or vehicle operation and no additional diagnosis or service is required for this condition at this time. Engineering is currently working on a solution for this condition that will reprogram the IPMA and is expected in Q2 2024. Monitor OASIS for additional information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 F-150 non-Lightning vehicles may exhibit reduced power and/or lack of acceleration above 4000 revolutions per minute (RPM) and/or not being able to shift above 4000 RPM. This may be due to the missing retainers (service part number W714040-S300) from the air cleaner intake. Prior to performing other diagnostics, inspect the air cleaner intake to determine if the retainers are present and fully seated. If the retainers are not present, install as necessary. Refer to the Workshop Manual (WSM), Section 303-12C Intake Air Distribution and Filtering - 3.5L EcoBoost (BM), Removal and Installation, Air Cleaner, Removal, Step 4. If the retainers are present, or the missing retainers were replaced and the symptom is still present, refer to the WSM for additional diagnostics. For claiming, use causal part 9C675 and applicable labor operations in Section 06 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022 F-150 Lightning vehicles equipped with a 15 inch center display screen (minor feature code HJGAY) may exhibit a 360 degree camera view that is smaller than the vehicle's center display screen. To confirm a vehicle is built with a certain minor feature code, review the build information by double-clicking the vehicle identification number (VIN) in the upper left corner in the Professional Technician System (PTS). This may be due to a recent update to the image processing module A (IPMA). To correct this condition, run the APIM - 360 camera view display configuration application using the latest software level of the Ford Diagnosis and Repair System (FDRS) scan tool. For claiming, use causal part 14G647 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022-2023 F-150 and 2023 F-Super Duty vehicles equipped with a direct current/alternating current converter module A (DCACA) inverter (minor feature code HUKAK) may exhibit a Please Contact Authorized Dealer For Service message in the center display screen with DTC P0A93:96 stored in the DCACA. This may be due to the software level of the DCACA and has no effect on vehicle operation. To confirm a vehicle is built with a certain minor feature code, review the build information by double-clicking the vehicle identification number (VIN) in the upper left corner in the Professional Technician System (PTS). To correct this condition, reprogram the DCACA to the latest software level using the latest version of the Ford Diagnosis and Repair System (FDRS) scan tool. For claiming, use causal part 19G317 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: ELECTRICAL SYSTEM:BODY CONTROL MODULE:SOFTWARE · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Software Update PU1009-SS-NS for 2023 MY F-150 vehicles is now available. Quality Improvements include: -Eliminate incorrect Fuel System Lean PCM Fault DTC/MIL setting. - Robustness action in operation of vehicle to detect low-state-of-charge battery and prevent engine stall, as well as provide improved warning to customers when low-state-of-charge conditions exist. - Eliminate potential ABS Yaw Rate Calibration issue. - Robustness action to prevent potential line pressure drift DTC from setting. - Eliminate False Positive Throttle DTC or MIL from setting - Eliminate potential ABS Yaw Rate Calibration issue. - Robustness action to alleviate the Nuisance SSN (Stop Safely Now) message from setting and vehicle should operate as expected in the next Key Start event - Eliminates potential Emergency Parking Brake activation when wire harness experience a short.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:SOFTWARE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 23-2367 to revise Step 8 of the Service Procedure. Some 2021-2023 F-150 vehicles equipped with a 400 watt direct current/alternating current (DC/AC) inverter system with a pickup bed alternating current (AC) power outlet socket may experience the DC/AC inverter system inoperative with diagnostic trouble code (DTC) B1330:9A stored in the body control module (BCM). This may be due to a connection issue at C4628
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 23-2363 to add 2021-2022 vehicle model years, update the symptom and the causal part. Some 2021-2023 F-150 vehicles equipped with a 3.5L PowerBoost engine may exhibit an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble code (DTC) P084B stored in the powertrain control module (PCM). This may be due to the software level of the PCM. To correct this condition, perform the Service Procedure below to reprogram the PCM to the latest software level via the Ford Diagnosis and Repair System (FDRS).
Source components: POWER TRAIN · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 23-2240 to to add labor operation H and correct parts list. Some 2021-2023 F-150 vehicles may exhibit a no crank/no start with a battery draw and air conditioning (A/C) clutch engaged at all times. This may be due to an opened diode in the A/C clutch field coil damaging the output driver (field effect transistor YFET) in the body control module C (BCMC). To correct the condition, follow the Service Procedure to replace the BCMC and A/C clutch field coil assembly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 23-2337 to update the Service Procedure and the causal part. Some 2022-2023 F-150 hybrid vehicles equipped with a 3.5L PowerBoost engine may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0420 and/or P0430 stored in the powertrain control module (PCM). This may be due to high sulfur content in the fuel. To correct the condition, follow the Service Procedure to reprogram the PCM and remove sulfur from the catalytic converters.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 23-2372 to add 2022 model year vehicle applications. Some 2022-2023 F-150 vehicles equipped with a 3.5L PowerBoost engine may exhibit an illuminated engine coolant temperature warning lamp with a Motor Coolant Over Temperature message in the IPC with diagnostic trouble code (DTC) P0A2F:94 stored in the secondary on-board diagnostic control module C (SOBDMC). This may be due to the software level of the SOBDMC. To correct this condition, perform the Service Procedure below to reprogram the SOBDMC to the latest software level via the Ford Diagnosis and Repair System (FDRS).
Source components: ENGINE AND ENGINE COOLING:COOLING SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Software Update SU7 P1 for 2021- 2023 MY F150 vehicles is now available. Quality improvements include: -21 MY Increases availability of BlueCruise. Ignition reset will not be necessary to reengage BlueCriuse. -21 MY Reduces false eyes-off warnings -22-23 MY Reduces erroneuos braking for objects that are not in the path for Rear Park Aid and Reverse Brake Assist features.
Source components: BACK OVER PREVENTION:SOFTWARE · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various 2021-2024 Ford and Lincoln vehicles equipped with the rear camera on demand feature may exhibit a Please Check Surroundings For Safety or Full View Not Available message when the rear camera button is pressed and the vehicle is not in reverse. Inform customers this condition is considered normal operation and does not affect vehicle durability because the full rear view camera image can only be shown when the vehicle is in reverse. No additional diagnosis or service is required for this condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 F-150 vehicles equipped with a direct current/alternating current converter module A (DCACA) inverter (minor feature code HUKAK) may exhibit a Pro Power Onboard Unavailable message in the vehilce center display screen with DTC B15DA:09 in the BCM. This may be due to the software level of the BCM and powertrain control module (PCM). To confirm a vehicle is built with a certain minor feature code, review the build information by double-clicking the vehicle identification number (VIN) in the upper left corner in the Professional Technician System (PTS). To correct this condition, perform the Service Procedure below to reprogram the BCM and PCM to the latest software level via the Ford Diagnosis and Repair System (FDRS).
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:INFOTAINMENT · EQUIPMENT:ELECTRICAL:INFOTAINMENT:SOFTWARE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022-2023 F-150 vehicles equipped with a 3.5L EcoBoost engine built on or after 01-Oct-2022, 2023 F-150 vehicles equipped with a 3.5L PowerBoost engine on or after 01-Oct-2022, and 2023 Expedition/Navigator vehicles built on 01-Dec-2022 and through 30-Apr-2023 may exhibit reduced engine power on startup and an illuminated MIL and/or powertrain malfunction (wrench) indicator with diagnostic trouble code (DTC) P2101 stored in the powertrain control module (PCM). This may be due to the software level of the PCM. To correct this condition, perform the Service Procedure below to reprogram the PCM to the latest software level via the Ford Diagnosis and Repair System (FDRS).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Software Update SU6 P3 for 2022- 2023 MY F150 vehicles is now available. Quality improvements include: - adds robustness to the Driver State Monitoring system and increases availability of BlueCruise and reduces false eyes-off warnings
Source components: BACK OVER PREVENTION:SOFTWARE · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 F-150 vehicles equipped with autowipers may exhibit an inoperative rain-sensing wipers feature, even when the feature is turned on in the Vehicle Settings menu. This may be due to the software level of the steering column control module (SCCM). To correct this condition, reprogram the SCCM using the latest software level of the Ford Diagnosis and Repair System (FDRS) located under the SW Updates tab. For claiming, use causal part 3F791 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: BACK OVER PREVENTION:SOFTWARE · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022-2023 F-150 Lightning vehicles equipped with front park aid (minor feature code HNLAB) may exhibit an inoperative front park aid feature with a Front Parking Sensors Not Available Sensors Blocked See Manual message in the IPC without any diagnostic trouble codes (DTCs) associated with the condition. To confirm a vehicle is built with a certain minor feature code, review the build information by double-clicking the vehicle identification number (VIN) in the upper left corner in the Professional Technician System (PTS). This may be due to the software level of the image processing module A (IPMA). This condition does not affect vehicle durability and no additional diagnosis or service is required for this condition at this time. Engineering is working on a solution that is expected in Q1 2024. Monitor OASIS for additional information and schedule service appointments once the repair becomes available.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 22-2324 to add an additional model year. Some 2021-2023 F-150 vehicles equipped with a 400 watt direct current/alternating current (DC/AC) inverter system with a pickup bed alternating current (AC) power outlet socket may experience the DC/AC inverter system inoperative with diagnostic trouble code (DTC) B1330:9A stored in the body control module (BCM). This may be due to a connection issue at C4628. To correct the condition, follow the Service Procedure to inspect the connector and secure the harness.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 F-150 vehicles may exhibit DTC U023A:08 after reprogramming the SCCM. Do not replace or reprogram the SCCM, image processing module A (IPMA) or their components for this condition at this time. This DTC does not alert the customer, will not affect vehicle durability and no additional diagnosis or service is required for this condition at this time. Engineering is currently working on a solution for this condition that will reprogram the IPMA and is expected in late December 2023. Monitor OASIS for additional information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022 F-150 vehicles may exhibit an inoperative headlamp after a body control module (BCM) software update. There may also be BCM diagnostic trouble codes (DTCs) B14E5:08 and/or B14E7:08 present. This may be due to a software incompatibility between the headlamp light emitting diode (LED) control module and the BCM. If this condition occurs after a BCM software update, confirm the BCM is at the latest software level and replace the headlamp LED module on the affected headlamp. Refer to Workshop Manual (WSM), Section 417-01.
Source components: ELECTRICAL SYSTEM:BODY CONTROL MODULE/BCM · EXTERIOR LIGHTING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 F-150 vehicles equipped with one-touch up/down front windows may exhibit a window not responding to one-touch controls, does not open all the way and/or bounces back when using the one-touch close function. These may be due to a calibration parameter in the driver door module (DDM) and/or passenger door module (PDM). To correct the condition, reprogram the DDM and PDM using the latest level of the Ford Diagnosis and Repair System (FDRS) scan tool then perform the Power Door Window Initialization procedure for both the DDM and the PDM. For claiming, use causal part number 14B291 and applicable labor times from Section 10 of the Service Labor Times Standard (SLTS) Manual.
Source components: VISIBILITY:POWER WINDOW DEVICES AND CONTROLS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 F-150, 2022-2023 Expedition/Navigator, 2022-2023 Mustang, 2020-2023 Transit, 2020-2023 Explorer/Aviator vehicles equipped with a 10R80/10R80MHT transmission may exhibit a harsh/delayed engagement and/or harsh/delayed shift, an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes. stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to the software in the powertrain control module (PCM) or transmission control module (TCM), the transmission solenoid ID strategy, sticking valves in the main control valve body and/or axial movement of the CDF clutch cylinder (7H351) sleeve.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Software Update PU1103-NAT-VCE for 2022-2023 F-150 vehicles is now available. Quality improvements include: - Digital owner Manual addition (2023MY Only) -Ford Blue Cruise Map expiration removal update. - Adds a "some display features may be temporarily unavailable" message to the SYNC screen when a SYNC update is installing. - Selectable Drive Modes - prevent default to normal mode due to loss of communication with SYNC - Improved SYNC Display and single toggle addition to disable certain features that will help enhance your towing experience. - Improved instant voice feedback share feature -Addresses SYNC reboot issue may occurs after 2 hours of continuous use.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2023 Explorer vehicles equipped with a 2.3L EcoBoost engine, 2022-2023 F-150 vehicles equipped with a 3.5L EcoBoost engine, and 2023-2024 Expedition/Navigator vehicles may exhibit an illuminated malfunction indicator lamp (MIL) and/or powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTCs) P25B3, P25B4, P25B5, P25B6, P2ABA, P2ABB, P2ABC, P2AB7, P2AB8, and/or P2AB9. This may be due to the software in the powertrain control module (PCM). To correct this condition, follow the Service Procedure to reprogram the PCM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 Ford and Lincoln vehicles equipped with SYNC 4 may exhibit the navigation feature in the center display screen only displaying imperial (feet and miles) units and not being able to change to metric (meters and kilometers) units. This may be due to the software level of the SYNC module (APIM). To correct this condition, follow the Service Procedure to update the APIM to the latest software level via a coordinated flash. NOTE: The APIM software update that addresses the symptom listed in this article may have been sent via Ford Power-Up software updates delivered over-the-air (OTA) to connected vehicles that have automatic updates enabled through the center display screen. Enter the vehicle identification number (VIN) in Professional Technician System (PTS) and check the OTA Dashboard under the Connected Vehicle tab for OTA update history. If an update to the APIM has successfully completed recently and the customer is reporting the symptoms are no longer present, this article may not apply.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supercedes TSB 22-2388 to update the Service Procedure and vehicle model years affected. Some 2021-2023 F-150 Raptor vehicles may experience a rattle noise from the exhaust at the exhaust tailpipe actuators. This may be due to the exhaust tailpipe actuator valves rattling inside the muffler assembly. To correct the condition, follow the Service Procedure to reprogram the powertrain control module (PCM) and install new exhaust tailpipe actuator and/or valve springs on the exhaust tailpipe actuator valves.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 23-2279 to update the Service Procedure. Some 2021-2023 F-150 vehicles equipped with a 3.5L PowerBoost hybrid engine, 2020-2023 Explorer vehicles equipped with a 3.3L hybrid engine and 2020-2023 Aviator vehicles equipped with a 3.0L hybrid engine may exhibit a powertrain malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0A1E stored in the powertrain control module (PCM). This may be due to the belt integrated starter generator (BISG). To correct this condition, follow the Service Procedure to diagnose and repair this symptom.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 F-150 hybrid vehicles equipped with a 3.5L PowerBoost engine built on or before 01-Mar-2023 may exhibit an illuminated malfunction indicator lamp (MIL) with DTCs P237C, P2C22 and/or P2C23 in the powertrain control module (PCM). This may be due to the exhaust heat exchanger bypass control valve. To correct this condition replace the muffler inlet pipe. Refer to Workshop Manual (WSM), Section 309-00D Exhaust System - 3.5L V6 PowerBoost (CN), Removal and Installation. For claiming, use causal part 5A212 and applicable labor times in Section 05 of the Service Labor Time Standards (SLTS) Manual.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2021-2023 Model Year F150, 2022 Model Year F53/F59 Stripped Chassis, 2022-2023 Model Year F650/F750, 2023 Model Year Ranger, 2024 Model Year Econoline - Body Control Module (BCM) Replacement
Source components: ELECTRICAL SYSTEM:BODY CONTROL MODULE/BCM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022-2023 F-150 hybrid vehicles equipped with a 3.5L PowerBoost engine may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0420 and/or P0430 stored in the powertrain control module (PCM). This may be due to high sulfur content in the fuel. To correct the condition, follow the Service Procedure to remove sulfur from the catalytic converters.
Source components: ENGINE AND ENGINE COOLING · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Software Update SU6 P2 for 2021-2023 F-150 vehicles is now available. Quality Improvements include: -Robustness actions to improve steering column control module signal management to reduce battery drain contribution. - Improvement in automatic rain sensor function.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 F-150 vehicles equipped with an IPC with a 4.2 inch display and built with minor feature code HKRAB may experience a resetting of the trip odometer and MPG information after a key cycle. To confirm a vehicle is built with minor feature code HKRAB, review the build information by double-clicking the vehicle identification number (VIN) in the upper left corner in the Professional Technician System (PTS). This condition may be due to the software level of the IPC. To correct this condition, reprogram the IPC to the latest software level using the Ford Diagnosis and Repair System (FDRS). Perform a brief road test after the software update to confirm the concern is no longer present. If the concern is still present, replace the IPC. For claiming, use causal part 10849 and applicable labor operations in Section 10 of the Service Labor Time Standards Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022-2023 F-150 Lightning vehicles may exhibit an illuminated powertrain temperature warning lamp accompanied by a Motor coolant over temperature message in the instrument panel cluster (IPC) with DTC P0A3C:94 stored in either the secondary on-board diagnostic control module B (SOBDMB) and/or the secondary on-board diagnostic control module C (SOBDMC). This may be due to the software within either the SOBDMB and/or SOBDMC. To correct this condition, follow the Service Procedure to bring both modules to the latest software level.
Source components: POWER TRAIN · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Harvest Program 23H05 Certain 2022 Model Year Navigator and 2022-2023 Model Year Mach-E, F150 Lightning, F150, Expedition and Bronco - Instrument Cluster Odometer Inspection
Source components: ELECTRICAL SYSTEM:INSTRUMENT PANEL:SPEEDOMETER/ODOMETER:SENSOR/SENDING UNIT · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Software Update SU6 P1 for 2021 - 2023 F150 is now available. Quality improvements include: - Digital owner Manual addition (2023MY Only) -Improved ""Ask on Exit"" pop- up functionality - Adds a ""some display features may be temporarily unavailable"" message to the SYNC screen when a SYNC update is installing. - Selectable Drive Modes - prevent default to normal mode due to loss of communication with SYNC - Improved SYNC Display and single toggle addition to disable certain features that will help enhance your towing experience. - Improved instant voice feedback share feature"
Source components: ELECTRICAL SYSTEM:ADAS:DRIVER MONITORING:SOFTWARE · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 F-150 vehicles equipped with a 3.5L PowerBoost engine may exhibit an illuminated powertrain malfunction (wrench) lamp with diagnostic trouble code (DTC) P084B stored in the powertrain control module (PCM)
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2023 Ford and Lincoln vehicles equipped with a 10R60/10R80/10R80 MHT/10R100 transmission may exhibit a whine noise at idle and/or while driving. This may be identified as coming from the bellhousing and the front of the transmission fluid pan. The whine noise may become louder when the transmission is at operating temperature and may increase with engine revolutions per minute (RPM) in the park (P) position. A small amount of whine noise is considered to be characteristic of the 10R60/10R80/10R80 MHT/10R100 transmissions due to the offset gear drivetrain in the front support and has no effect on durability. Use the Report a Vehicle Concern link at the bottom of OASIS to submit a report if there is a customer concern of whine noise describing operating conditions and noise severity.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles equipped with power folding mirrors may exhibit power folding mirrors that are inoperative or exhibit a clicking sound. This may be due to the mirrors being manually folded in, during transportation, going through a car wash, bumped in a parking lot, or found during pre-delivery inspection (PDI). Prior to the replacement of any components, attempt to synchronize the mirrors by following the Power Mirrors Synchronization procedure. Refer to Workshop Manual (WSM) Section 501-09 Rear View Mirrors - General Procedures - Power Mirrors Synchronization.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 F-150 vehicles equipped with a direct current/alternating current converter module A (DCACA) inverter (minor feature code HUKAK) may exhibit an illuminated tire pressure monitoring system (TPMS) indicator with diagnostic trouble code (DTC) B124D stored in the BCM. This may be due to the DCACA inverter causing radio frequency interference (RFI). To confirm a vehicle is built with a certain minor feature code, review the build information by double-clicking the vehicle identification number (VIN) in the upper left corner in the Professional Technician System (PTS). To correct this condition, follow the Service Procedure to confirm if the inverter is the source of RFI and mitigate the interference.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 F-150, 2022-2023 Expedition vehicles equipped with 10 channel audio digital signal processing (DSP) module may exhibit a pop noise and/or static in the speakers at start up that cannot be turned down or off using the audio system controls. To confirm a vehicle is built with a 10 channel DSP module, verify the minor feature code, F-150 (IDBBQ)/Expedition (IDBAP or IDBBR), by reviewing the build information by double-clicking the vehicle identification number (VIN) in the upper left corner in the Professional Technician System (PTS) website. To correct the condition, reprogram the DSP module to the latest software level using the Ford Diagnosis and Repair System (FDRS) diagnostic scan tool. For claiming, use causal part 18B849 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 Ford and Lincoln vehicles may exhibit DTCs U2100 and/or U3002 stored in the cruise control module (CCM), side obstacle detection control module LH (SODL), side obstacle detection control module RH (SODR), side obstacle detection control module C (SODCMC) and/or side obstacle detection control module D (SODCMD) after a module replacement. DTC U2100 may set when the module has not been properly configured after replacement. DTC U3002 may set when the module has been configured with the incorrect VIN. To correct this condition, verify that the module storing the DTC has been installed following the applicable Workshop Manual (WSM) Removal and Installation procedure. If the DTC is still stored, download and run the Vehicle Identification Number (VIN) Write application found under Toolbox, Multi-Module tab in the Ford Diagnosis and Repair System (FDRS).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 F-150 vehicles may exhibit an illuminated airbag indicator light that may be accompanied by diagnostic trouble codes (DTCs) U3000:41 and/or U3000:54 in the occupant classification system module (OCSM) and/or B00A0:09, B00A0:63, B00A0:64 and/or B00A0:68 in the restraints control module (RCM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 F-150 vehicles equipped with a 3.5L hybrid engine, 2020-2023 Explorer vehicles equipped with a 3.3L hybrid engine and 2020-2023 Aviator vehicles equipped with a 3.0L hybrid engine may exhibit a powertrain malfunction indicator lamp with diagnostic trouble code (DTC) P0A1E stored in the powertrain control module (PCM). This may be due to the belt integrated starter generator (BISG). To correct this condition, follow the Service Procedure to diagnose and repair this symptom.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 F-150 vehicles may exhibit all modules on the HS2, HS3, HS4 and MS CAN networks not responding to the Ford Diagnosis and Repair System (FDRS) and modules on these networks fail the network test. Modules on the FD1 and HS1 networks will communicate with the FDRS. Vehicles equipped with a power opening/closing tailgate may also exhibit an inoperative power tailgate. This may be due to a gateway module (GWM) that is not configured properly. To correct this condition, download and run the GWM - Gateway Module A (GWM) Configuration application. For claiming, use causal part number 14G490 and applicable labor times from Section 10 of the Service Labor Times Standard (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Priority Update 23-PU0724-DOM-RS for 2021-2023 F-150 vehicles is now available. Quality Improvements include: - Various Apple Carplay quality improvements
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 22-2428 and 23-2176 to update the Issue, Action and Service Procedure. Some 2017-2023 F-150, 2018-2023 Expedition/Navigator/Mustang, 2019-2023 Ranger, 2020-2023 Explorer/Aviator/Transit and 2021-2023 Bronco vehicles equipped with a 10R60/10R80/10R80MHT transmission may exhibit a harsh/delayed engagement and/or harsh/delayed shift, an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to the software in the powertrain control module (PCM) or transmission control module (TCM), the transmission solenoid ID strategy, sticking valves in the main control valve body and/or axial movement of the CDF clutch cylinder (7H351) sleeve. To correct the condition, follow the Service Procedure to identify and correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
In various 2017-2023 Ford and Lincoln vehicles, customers may receive a message in the FordPass or LincolnWay App stating Feature Unavailable. Since this is a fleet vehicle, it cannot access the (SYNC Connect) FordPass or LincolnWay app through the TCU Embedded Modem. If this message appears, the vehicle may be equipped with a fleet telematics module. Replacement of the TCU or TCU related repairs will not prevent this message from appearing. Refer the customer to in app FordPass Guides or LincolnWay Concierge Teams to aid with fleet telematics removal. Open app, select Account > Help > CHAT or CALL option.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 F-150 vehicles may exhibit a no crank/no start with a battery draw and air conditioning (A/C) clutch engaged at all times. This may be due to an opened diode in the A/C clutch field coil damaging the output driver in the body control module C (BCMC). To correct the condition, follow the Service Procedure to replace the BCMC and A/C clutch field coil assembly.
Source components: ELECTRICAL SYSTEM:BODY CONTROL MODULE/BCM · EQUIPMENT · UNKNOWN OR OTHER.