2015 Ford F-150 Manufacturer communications & TSBs.Page 2
Original record summaries, dates and identifiers for this model-year. Records 101–200 of 249, ordered newest first. Dated records on this page: Jun 21, 2016–Apr 23, 2019.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Apr 23, 2019Service Bulletin/Repair Instructions
18N03-S6
NHTSA communication ID: 10159511
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2015-2018 Model Year F-150 and 2017-2018 Model Year F-250-F-550 Vehicles - Door Latch Freezing Concerns
NHTSA source summary · Original PDF not reviewed by Recallfolio
SSM 47922 - Various Vehicles - 2.7L/3.0L EcoBoost Engine - Oil Filter Service Tip When servicing the oil filter on vehicles equipped with a 2.7L or 3.0L EcoBoostengine it is critical to inspect the oil filter housing center stem to verify is not separated or damaged. If the center stem is damaged or separated from the housing this will result in oil flow through the reservoir drain port causing low engine oil pressure and internal engine damage. If the filter housing stem is damaged or separated, the oil filter housing must be replaced. If the center stem is not damaged or separated, the O-ring seals on the stem and housing must be replaced each time the filter is serviced.
Source components: ENGINE · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2015 - 2019 Model Year F-150 and 2017 â 2019 Model Year F-Super Duty Vehicles Equipped with Engine Block Heaters - Engine Block Heater Cord Replacement
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2019 F-150 vehicles may exhibit a glove box door that appears misaligned along the storage tray or right side instrument panel when closed. This may be due to the position of the glove box storage tray rubber mat or the seating of the glove box door strikers or glove box door hinge pins. To resolve the condition, reposition or adjust the affected component according to the Service Procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2017 vehicles may experience a no crank concern due to a security access key table error. When attempting to program keys or perform a parameter reset, the procedure may fail and the Integrated Diagnostic System (IDS) scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the Body Control Module (BCM) is internally faulted and requires replacement. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2017 vehicles may experience a no crank concern due to a security access key table error. When attempting to program keys or perform a parameter reset, the procedure may fail and the Integrated Diagnostic System (IDS) scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the Body Control Module (BCM) is internally faulted and requires replacement. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2019 F-150 XL/XLT vehicles may exhibit warping/separation of the instrument panel at the defrost vents. To resolve the condition, replace the instrument panel upper section.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2019 F-150 XL/XLT vehicles may exhibit warping/separation of the instrument panel at the defrost vents. To resolve the condition, replace the instrument panel upper section.
Source components: ELECTRICAL SYSTEM · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2016 F-150 vehicles built on or before 01-Feb-2016, 2019 F-150 vehicles built on 11-Oct-2018 and through 15-Nov-2018 and 2019 F-Super Duty vehicles built on 10-Oct-2018 and through 27-Nov-2018 equipped with adaptive cruise control may exhibit an unintended deceleration event while passing a large object such as a tractor trailer. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2016 F-150 vehicles built on or before 01-Feb-2016, 2019 F-150 vehicles built on 11-Oct-2018 and through 15-Nov-2018 and 2019 F-Super Duty vehicles built on 10-Oct-2018 and through 27-Nov-2018 equipped with adaptive cruise control may exhibit an unintended deceleration event while passing a large object such as a tractor trailer. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2000 and newer Ford, Lincoln and Mercury vehicles equipped with aluminum body panels may exhibit corrosion concerns appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended. Follow the Service Procedure steps to correct the condition
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2000 and newer Ford, Lincoln and Mercury vehicles equipped with aluminum body panels may exhibit corrosion concerns appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended. Follow the Service Procedure steps to correct the condition
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2019 F150/Edge, 2016-2018 MKX, 2019 Nautilus and 2017-2019 Fusion/Continental vehicles equipped with a 2.7L engine may exhibit a malfunction indicator lamp (MIL) and/or wrench lamp with diagnostic trouble codes (DTCs) P0116, P0117, P0118, P0119, P0217, P0330, P1026, and/or P130D. This may be due to a engine coolant temperature (ECT) sensor connector which is not fully seated or damaged wiring between connectors C1064 and C1047 for F150 and C1016 and C1168 for Edge/MKX/Nautilus/Fusion/Continental vehicles. ECT sensors should not be replaced if damaged wiring is found at or near these connectors. For claiming, use causal part 12A699 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING:COOLING SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2019 F150/Edge, 2016-2018 MKX, 2019 Nautilus and 2017-2019 Fusion/Continental vehicles equipped with a 2.7L engine may exhibit a malfunction indicator lamp (MIL) and/or wrench lamp with diagnostic trouble codes (DTCs) P0116, P0117, P0118, P0119, P0217, P0330, P1026, and/or P130D. This may be due to a engine coolant temperature (ECT) sensor connector which is not fully seated or damaged wiring between connectors C1064 and C1047 for F150 and C1016 and C1168 for Edge/MKX/Nautilus/Fusion/Continental vehicles. ECT sensors should not be replaced if damaged wiring is found at or near these connectors. For claiming, use causal part 12A699 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2019 F-150 vehicles equipped with a 3.0L diesel engine built on or before 25-Jan-2019 may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0234, P208E and/or P2201 stored in the powertrain control module (PCM). Follow the Service Procedure steps to correct the condition.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:APPLIANCE:AIR CONDITIONER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2019 F-150 vehicles equipped with a 3.0L diesel engine built on or before 25-Jan-2019 may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0234, P208E and/or P2201 stored in the powertrain control module (PCM). Follow the Service Procedure steps to correct the condition.
Source components: EQUIPMENT:APPLIANCE:AIR CONDITIONER · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2012-2019 Vehicles may require repairs to the Smartlink system. Smartlink is a Ford Licensed Accessory which has a warranty provided by the accessory manufacturer. Warranty replacement parts for Smartlink that are ordered through Ford are not reimbursable through the Ford Motor Company warranty system. Please see the Warranty and Policy Manual for further information on Ford Licensed Accessories.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2019 F-150 vehicles may exhibit a console media bin door that will not open or is binding. This may be due to the console media bin door inertia switch being stuck in the active position. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015 F-150 vehicles equipped with a 2.7L EcoBoost engine built on or before 5-Oct-2015 may exhibit an illuminated MIL with DTC P2450 stored in powertrain control module (PCM). Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2019 F-150, 2017-2019 F-Super Duty, 2018-2019 Expedition/Navigator vehicles equipped with a vista roof opening panel may exhibit a binding/sticking, glass stuck open or closed, noisy operation including chatter, rattling, or grinding. This may be due to the glass brackets cracking and/or breaking apart. The glass panel brackets are serviceable separately from the frame assembly and require the roof opening panel glass to be moved to the vent position. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2018 C-Max, 2013-2019 Escape/Fusion/MKZ, 2015-2018 Focus, 2015-2019 Edge/F150/MKC/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017 Super Duty, 2018-2019 EcoSport/Expedition, and 2019 Nautilus vehicles may experience seat pan looseness, lateral movement, or clunk/thump noise on turns. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. For all turbocharged engine applications, the turbocharger oil supply filter (6C683 gas engine/6L625 connector style or 6A968 diesel engine) must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.
Source components: ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2013-2019 vehicles equipped with a LKS system with customer complaints of steering wheel vibration, steering pull or vehicle drift may be due to an alert and/or steering aid input from the LKS. The LKS system detects unintentional drifting toward the outside of the lane and alerts and/or aids vehicle to stay in the lane. Be sure the customer understands how the lane departure warning feature settings work for Alert (steering wheel vibration) and Aid (steering input toward lane center). Further information on the LKS can be found in the owners manual. If the customers concern is due to the LKS functioning as intended, do not attempt to repair.
Source components: STEERING · STEERING: STEERING WHEEL/HANDLE BAR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When connecting the Vehicle Communication Module (VCM) and Integrated Diagnostic System (IDS) or Ford Diagnosis and Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic trouble codes (DTCs), no start, no crank conditions or the IPC inoperative. If a vehicle displays these issues, disconnect the equipment from the DLC and disconnect the vehicle battery. Wait 10 minutes and reinstall with the ignition off. Clear any DTCs present and retest.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2011-2015 F-150 vehicles equipped with a 3.5L EcoBoost engine and built on or before 29-May-2015 may exhibit a ticking/tapping or rattle type noise from the top front cover area of the engine upon initial start-up that may last for 2-5 seconds after a cold soak of 6 hours or more. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2018 Model Year Expedition and Navigator Vehicles Equipped With R-1234yf Refrigerant - Special R-1234yf Refrigerant Service Information. Certain 2015-2018 Model Year F-150 and 2017-2018 Model Year F-250-F-550 - Vehicles - Door Latch Freezing Concerns
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 F-150 vehicles may exhibit a glove box door that appears misaligned along the storage tray or right side instrument panel when closed. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2018 F-150/Expedition/Navigator vehicles may exhibit an intermittent grinding noise coming from the right or left IWE area in 2WD mode. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When connecting the Vehicle Communication Module (VCM) and Integrated Diagnostic System (IDS) or Ford Diagnosis and Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic trouble codes (DTCs), no start, no crank conditions or the IPC inoperative. If a vehicle displays these issues, disconnect the equipment from the DLC and disconnect the vehicle battery. Wait 10 minutes and reinstall with the ignition off. Clear any DTCs present and retest.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 F-150 vehicles equipped with a 3.3L/3.5L Duratec, 3.5L EcoBoost and 5.0L engine and equipped with a block heater may exhibit a lack of heat concern from the heating ventilation and air conditioning (HVAC) system when operating the vehicle consistently in temperatures that are below -20Å?C (4Å?F). This condition may be due to deposits from the engine coolant becoming trapped in the heater core. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 F-150 vehicles equipped with a 3.3L, 3.5L Duratec, 3.5L EcoBoost and 5.0L engine without a block heater may exhibit a lack of heat concern from the heating ventilation and air conditioning (HVAC) system when operating the vehicle in temperatures consistently below -20 degrees C (4 degrees F). This condition may be due to deposits from the engine coolant becoming trapped in the heater core. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some Ford and Lincoln vehicles equipped with a 2.7L or 3.0L EcoBoost engine may exhibit an oil leak from the engine oil pan RTV seal. Replace the oil pan following the procedure in Workshop Manual (WSM) Section, 303-01. After removing the oil pan it is suggested to allow the crankcase to drain overnight to minimize the chance of residual oil contaminating the crankcase sealing rail. Remove all traces of old RTV and clean the engine sealing surface using only Motorcraftù Metal Brake Parts Cleaner, then wipe with Motorcraftù Metal Surface Prep Wipes and allow to air dry. Refer to WSM, Section 303-00 > RTV Sealing Surface Cleaning and Preparation. If possible, allow the new RTV sealant to cure for 4 hours before refilling the engine with oil. Skipping or improperly completing steps may result in repeat oil pan leaks.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 F-150, 2017-2018 F-Super Duty, 2018 Expedition/Navigator vehicles equipped with a vista roof opening panel may exhibit a concern with the glass panel brackets. The brackets may crack and/or break apart resulting in symptoms that include but are not limited to binding/sticking, glass stuck open or closed, noisy operation including chatter, rattling, or grinding. The roof opening panel glass brackets are available for service as a kit (FL3Z-1651070-C). Refer to Workshop Manual (WSM), Section 501-17 for diagnosis and repair procedures. Make sure the track is free of debris prior to assembly. For claiming, use causal part 1651070 and applicable labor operations in Section 12 of the Service Labor Time Standards (SLTS) Manual. Labor operations for removal and installation of the glass and glass brackets (guides) apply.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2018 F-150, 2015-2018 Transit/Expedition, and 2015-2017 Navigator vehicles equipped with a 3.5L EcoBoost engine with greater than 20,000 miles may exhibit a tick type noise from the cylinder block area. This noise may be caused by a cracked piston skirt. The noise can be isolated to a cylinder using a stethoscope or other suitable listening device. Canceling the affected cylinder will reduce or eliminate the noise. If the noise is isolated to a specific cylinder, it is recommended to replace the short block. If the noise cannot be isolated using the methods described, refer to the Workshop Manual (WSM) for diagnosis. A cracked piston skirt does not result in metal contamination of the engine or any related cylinder head damage. Prior approval for short block replacement is not required under new vehicle limited warranty coverage.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2018 F-150, 2015-2018 Transit/Expedition, and 2015-2017 Navigator vehicles equipped with a 3.5L EcoBoost engine with greater than 20,000 miles may exhibit a tick type noise from the cylinder block area. This noise may be caused by a cracked piston skirt. The noise can be isolated to a cylinder using a stethoscope or other suitable listening device. Canceling the affected cylinder will reduce or eliminate the noise. If the noise is isolated to a specific cylinder, it is recommended to replace the short block. If the noise cannot be isolated using the methods described, refer to the Workshop Manual (WSM) for diagnosis. A cracked piston skirt does not result in metal contamination of the engine or any related cylinder head damage. Short block replacement does not require prior approval.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2018 F-150 and 2017-2018 Expedition/Navigator vehicles may exhibit an intermittent grinding noise coming from the right or left IWE area in 2WD mode. This may be caused by an intermittent leak in the check valve. Before completing any normal diagnosis suspect that the check valve is the root cause of the issue. If the check valve has been ruled out as the root cause for the issue refer to Work Shop Manual 308-07 and follow normal diagnosis.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 F-150 and 2017-2018 F-Super Duty vehicles may exhibit a lack of cooling from the heating ventilation air conditioning (HVAC) system due to a low refrigerant charge. Using an ultraviolet (UV) leak detection light, inspect the condenser near the receiver/dryer cap for the presence of dye. If dye is present, replace the condenser. For claiming, use causal part 19712 and applicable labor operations in Section 11 of the Service Labor Time Standards (SLTS) Manual
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 F-150 may exhibit a dash panel distortion at the defrost duct area. Engineering is investigating the condition. Do not attempt repair at this time.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018 Expedition/Navigator vehicles built on or before 24-Feb-2018, 2017-2018 F-Super Duty built on or before 26-Feb-2018 and Transit vehicles built on or before 26-Feb-2018 and 2015-2018 F-150 vehicles built on or before 3-Mar-2018 may exhibit a trailer connected and/or disconnected message in the IPC without a trailer connected. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some Ford and Lincoln vehicles equipped with a 2.7L or 3.0L EcoBoost engines may exhibit an oil leak from the engine oil pan RTV seal. Replace the oil pan by performing the published Workshop Manual (WSM) service procedures. After removing the oil pan, it is suggested to allow the crankcase to drain overnight to minimize the chance of residual oil contaminating the crankcase sealing rail. Remove all traces of old RTV, clean the engine sealing surface with only Motorcraftù Metal Brake Parts Cleaner then wipe with Motorcraftù Metal Surface Prep Wipes, and allow to air dry as directed in WSM, Section 303-00, RTV Sealing Surface Cleaning and Preparation. If possible, after the new oil pan is installed, allow the new RTV sealant to cure for 4 hours before refilling the engine with oil. Ford is investigating this concern. Monitor OASIS for future updates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Replacing the original equipment SYNC/Navigation system with either an aftermarket SYNC/Navigation kit or modifying original SYNC/Navigation parts to provide additional features is not recommended nor supported on any Ford, Mercury or Lincoln vehicle. Only approved Genuine Ford accessories or originally installed systems are supported and certified to function correctly with other vehicle systems. If you suspect a system has been modified, the following resources can be used to verify original equipment: Monroney Label (Window Sticker), Professional Technician Society (PTS) OASIS tab select SYNC or HVBOM. For Genuine Ford accessories use: PTS Workshop Tab select Dealer Installed Accessory or Accessory Installation.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2018 F-150/Expedition/Navigator 4x4 vehicles may exhibit an intermittent grinding noise coming from the right front or left front wheel area while accelerating in 2WD mode. Refer to the Workshop Manual (WSM), Section 308-07, Diagnosis and Testing Symptom Chart - NVH > The front axle makes noise in 2H mode only and generally under heavy throttle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2010-2018 various vehicles equipped with SYNC or SYNC 3 may not function when attempting to find or use the Spotify app via AppLink. As of an update released on 1/15/2018 Spotify will no longer be supporting their AppLink integration. No repair attempts should be attempted to correct this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 F-150 vehicles equipped with power folding mirrors may exhibit the mirror housing vibrating while driving, moving freely or not moving to the desired position after the mirror is manually folded. Refer to the Owner's Manual for the power mirror synchronization procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When connecting the Vehicle Communication Module (VCM) and Integrated Diagnostic System (IDS) or Ford Diagnosis and Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic trouble codes (DTCs), no start or no crank conditions or the IPC inoperative. For Lincoln vehicles, this information is now listed in the Technical Inspection and Post Road Test Sections of ePDI on the PTS website. If a vehicle displays these issues, disconnect the equipment from the DLC and disconnect the vehicle battery. Wait 10 minutes and reinstall with the ignition off. Clear any DTCs present and retest.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 F-150, 2017-2018 F-Super Duty, 2018 Expedition/Navigator vehicles equipped with a vista roof opening panel may exhibit binding while opening or closing of the movable glass panel. The roof opening panel glass brackets are available for service. Both brackets must be replaced, FL3Z-1651070-A right side and FL3Z-1651071-A left side. Refer to Workshop Manual (WSM), Section 501-17 for removal and installation procedure. For claiming, use causal part 1651070 or 1651071. Use part number 51070 to look up applicable labor operations, listed in Section 12 of the Service Labor Time Standards (SLTS) manual
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 F-150, 2017-2018 F-Super Duty, 2018 Expedition/Navigator vehicles equipped with a vista roof opening panel may exhibit binding while opening or closing of the movable glass panel. The roof opening panel glass brackets are available for service. Both brackets must be replaced, FL3Z-1651070-A right side and FL3Z-1651071-A left side. Refer to Workshop Manual (WSM), Section 501-17 for removal and installation procedure. For claiming, use causal part 51070 and applicable labor operations in section 12 of the service labor time standards (SLTS) manual.
Source components: STRUCTURE:BODY:ROOF AND PILLARS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 F-150, 2017-2018 F-Super Duty, 2018 Expedition/Navigator vehicles equipped with a vista roof opening panel may exhibit binding while opening or closing of the movable glass panel. The roof opening panel glass brackets are available for service. Both brackets must be replaced, FL3Z-1651070-A right side and FL3Z-1651071-A left side. Refer to Workshop Manual (WSM), Section 501-17 for removal and installation procedure. For claiming, use causal part 51070 and applicable labor operations in section 12 of the service labor time standards (SLTS) manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 F-150, Mustang and Transit vehicles built on or before 01-Dec-2017 may have a concern of no airflow from the climate control vents. This may be caused by a seized or sticking A/C clutch. This can be repaired by replacing only the A/C clutch (19D786/19D784). The compressor assembly (19703) may not be required. Refer to Workshop Manual, Section 412-00 for A/C clutch removal. It may be necessary to lightly tap around the stuck area of the clutch with a rubber mallet to free it from the pulley for removal. Refer to applicable labor operations from Section 11 of the SLTS maunual when replacing the A/C clutch.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 F-150, Mustang and Transit vehicles built on or before 01-Dec-2017 may have a concern of no airflow from the climate control vents. This may be caused by a seized or sticking A/C clutch. This can be repaired by replacing only the A/C clutch (19D786/19D784). The compressor assembly (19703) may not be required. Refer to Workshop Manual, Section 412-00 for A/C clutch removal. It may be necessary to lightly tap around the stuck area of the clutch with a rubber mallet to free it from the pulley for removal. Refer to applicable labor operations from Section 11 of the SLTS maunual when replacing the A/C clutch.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The Accessory (Wireless) Keyless Entry Keypad can only be used with vehicles that are factory built with Remote Keyless Entry (RKE). The master code for the Accessory (Wireless) Keyless Entry Keypad can be retrieved from FMCDealer - Parts and Service - Parts Product Line Information - Keys/Entry Devices - Aftermarket Keyless Entry Keypad Code Access. Access to this site is granted through Dealer Program Enrollment System (DPES) and Dealer Principal, General Manager or Parts and Service Director can authorize users. Once authorized the retrieval process for master code can be obtained. The master code for the Accessory Keyless Entry Keypad cannot be retrieved from the body control module(BCM) with a diagnostic tool.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The Accessory (Wireless) Keyless Entry Keypad can only be used with vehicles that are factory built with Remote Keyless Entry (RKE). The master code for the Accessory (Wireless) Keyless Entry Keypad can be retrieved from FMCDealer - Parts and Service - Parts Product Line Information - Keys/Entry Devices - Aftermarket Keyless Entry Keypad Code Access. Access to this site is granted through Dealer Program Enrollment System (DPES) and Dealer Principal, General Manager or Parts and Service Director can authorize users. Once authorized the retrieval process for master code can be obtained. The master code for the Accessory Keyless Entry Keypad cannot be retrieved from the body control module(BCM) with a diagnostic tool.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 F-150, 2017-2018 F-Super Duty, 2018 Expedition/Navigator vehicles equipped with a vista roof opening panel may exhibit binding while opening or closing of the movable glass panel. The roof opening panel glass brackets are available for service. Both brackets must be replaced, FL3Z-1651070-A right side and FL3Z-1651071-A left side. Refer to Workshop Manual (WSM), Section 501-17 for removal and installation procedure. For claiming, use causal part 1651070 and applicable labor operations in section 12 of the service labor time standards (SLTS) manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2016 F-Super Duty pickup vehicles equipped with a 6.7L engine may exhibit an illuminated malfunction indicator lamp (MIL) with DTCs P2201, P2459, P2463 and/or P246C. Reprogram the powertrain control module (PCM) to the latest calibration using Integrated Diagnostic System (IDS) or Ford J2534 Diagnostic Software (FJDS) release 106.01 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. Calibration files may also be obtained at www.motorcraftservice.com.
Source components: ELECTRICAL SYSTEM · EXTERIOR LIGHTING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 F150/Edge, 2016-2018 MKX and 2017-2018 Fusion, Continental vehicles equipped with a 2.7L engine may experience a malfunction indicator lamp (MIL) and/or wrench lamp with Diagnostic Trouble Codes (DTCs): P0116, P0117, P0118, P0119, P0217, P0330, P1026, and/or P130D. This may be due to a engine coolant temperature (ECT) sensor connector which is not fully seated or damaged wiring between connectors C1064 and C1047 for F150 and C1016 and C1168 for Edge/MKX/Fusion/Continental vehicles. ECT sensors should not be replaced if damaged wiring is found at or near these connectors. If an issue with the wiring is found use causal part 12A699.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2017 F-150 vehicles may exhibit intermittent and/or inoperative A/C, radio, and/or power window switch control with multiple illuminated warning indicators and/or diagnostic trouble codes (DTCs) U0140, U0155, U0253, U0401, and/or U0452 stored in the front controls interface module (FCIM). This may be caused by excessive network traffic on the controller area network (CAN) Bus causing the FCIM to lock up. Before replacing the FCIM, complete a battery reset, clear all DTCs and run a FCIM self-test. If the issue is still present, follow normal diagnosis. For claiming, use causal part 18842 and applicable labor operations in section 10 of the service labor time standards (SLTS) manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit a no start condition with an illuminated malfunction indicator lamp (MIL) and a DTC P161A after PCM replacement. This may be due to the parameter reset procedure not being properly completed. To clear this DTC, use the Ford Integrated Diagnostic System (IDS) service tool or Ford J2534 Diagnostic Software, select - Toolbox - Body - Security - PATS Functions - Parameter Reset. Follow the on-screen instructions to complete the procedure. This procedure will transfer the existing Key ID information between the modules without the need of having 2 programmed PATS keys present. There is no need to program keys when the PCM is going to be replaced. Additional information can be found in the Workshop Manual (WSM), Section 419-01. Missing or lost keys are not warrantable.
Source components: ELECTRICAL SYSTEM · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 F-150 vehicles equipped with a vista roof opening panel may exhibit binding while opening or closing of the movable glass panel. The roof opening panel glass bracket is available for service. Both brackets must be replaced. Refer to Workshop Manual (WSM), Section 501-17 for removal and installation procedure. For claiming, use causal part 1651070 and applicable labor operations in section 12 of the service labor time standards (SLTS) manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2017 F-150 vehicles may experience intermittent loss of throttle pedal response, illuminated wrench, hill descent, airbag, anti lock brake system(ABS) and/or advanced trac warning indicators and/or P2122, P2123, P2124, P2125, P2127, P2128 and/or P2138 DTCs. This may be caused by the Accelerator Pedal Position (APP) Sensor 14A005 harness being improperly routed behind the brake booster to brake pedal bracket. If the harness is improperly routed, loosen the bracket to free the harness, refer to Workshop Manual (WSM), Section 206-06. Inspect and repair damaged circuits before properly routing the harness. If the harness is properly routed, proceed with normal diagnostics.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2017 F-150 vehicles equipped with a 3.5L Duratec or 5.0L engine may exhibit a lack of heat concern from the heating ventilation and air conditioning (HVAC) system when the vehicle is operated in temperatures that are consistently below -20 Å?C (4 Å?F). This condition may be due to deposits from the engine coolant becoming trapped in the heater core. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2017 Explorer and 2015-2016 F-150 vehicles, equipped with 3.5L Gasoline Turbocharged Direct Injection (GTDI) engines may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P2195, P2197, P2626, and/or P2629 stored in powertrain control module (PCM) memory. Follow the Service Procedure Steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2017 F-150, 2017 F-Super Duty vehicles may have concerns where the instrument cluster defaults back to the trailer tow setup screen every key cycle with no trailer attached. Refer to the Information Display section of the Owners Manual or the following steps to correct this concern. Type 1 and 2 Cluster small display Use the information display controls on the steering wheel and the information display menu. Navigate to Towing and press OK, select Trailer Options and press OK, choose Select Trailer and press OK, finally select No Active Trailer and press OK. Type 3 Cluster large display Use the information display controls on the steering wheel and the information display menu. Navigate to Towing tab, select Trailer Setup and press OK, then press OK to enter Trailer Options, select Change Trailer Selected and press OK, finally select No Active Trailer and press OK.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2015 F-150 VEHICLES EQUIPPED WITH A 5.0L ENGINE AND BUILT ON 15-APRIL-2015 AND THROUGH 15-JULY-2015 MAY EXHIBIT A 6-3 AND OR 5-3 DOWNSHIFT SQUAWK NOISE ON HARD ACCELERATION. THIS MAY BE CAUSED BY THE OVERDRIVE CLUTCH PLATE MATERIAL. A REVISED CLUTCH PLATE PART NUMBER 9L3Z-7B164-E SHOULD BE USED TO RESOLVE THIS CONCERN. ADVISE THE CUSTOMER THAT DRIVING IN A VARIETY OF CITY AND HIGHWAY SETTINGS AND TO LIMIT TOWING FOR 1,000 MILES AFTER THE REPAIR WILL INCREASE THE CHANCES FOR PROPER OVERDRIVE CLUTCH PLATE BREAK IN. FOR CLAIMING, USE CAUSAL PART 7B164 AND APPLICABLE LABOR OPERATIONS IN SECTION 07 OF THE SERVICE LABOR TIME STANDARDS (SLTS) MANUAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2009-2017 VEHICLES EQUIPPED WITH A 6R80, 6R100, 6R140 AUTOMATIC TRANSMISSION HAVE AN UPDATED MAIN CONTROL VALVE BODY OVERHAUL PROCEDURE. REFER TO WORKSHOP MANUAL (WSM), SECTION 307-01 FOR MAIN CONTROL VALVE BODY (7A100) OVERHAUL PROCEDURES. NOT ALL VALVE BODIES REQUIRE REPLACEMENT. INSPECT THE VALVE BODY BORES, SPRINGS AND VALVES AS DIRECTED DURING DIAGNOSIS AND REPAIR. REFER TO GENERAL SERVICE BULLETIN (GSB) G0000093 AUTOMATIC TRANSMISSION MAIN CONTROL INSPECTION FOR A VIDEO CLIP TO AID IN THE DIAGNOSIS OF THESE REPAIRS.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2015-2017 F-150 SUPERCAB VEHICLES BUILT ON OR BEFORE 01-JAN-2017 MAY EXHIBIT INOPERATIVE REAR DOOR LOWER LATCHES DURING FREEZING TEMPERATURES. THE REAR DOOR LOWER LATCHES HAVE BEEN REVISED TO INCLUDE A WATER SHIELD AND THE PARTS CATALOG HAS BEEN UPDATED TO SHOW THE NEW NUMBERS. REPLACE THE REAR DOOR LOWER LATCHES, REFER TO WORKSHOP MANUAL (WSM), SECTION 501-14. FOR CLAIMING, USE CAUSAL PART 18264A00 AND APPLICABLE LABOR OPERATIONS IN SECTION 12 OF THE SERVICE LABOR TIME STANDARDS (SLTS) MANUAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2015-2017 F-150 VEHICLES EQUIPPED WITH A 6R80 TRANSMISSION MAY EXPERIENCE AN INTERMITTENT LOSS OF REVERSE ENGAGEMENT OR A NEUTRAL STATE WHEN PERFORMING A SPECIFIC SHIFT PATTERN. THIS MAY OCCUR AFTER SHIFTING FROM MANUAL 1 OR MANUAL 2 TO REVERSE AT LOW SPEEDS WHILE THE VEHICLE IS ROLLING. SHIFTING THE TRANSMISSION INTO PARK AND CYCLING THE IGNITION OFF AND BACK ON WILL RESTORE REVERSE ENGAGEMENT. NORMAL CHARACTERISTIC DO NOT ATTEMPT REPAIR.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2015-2016 F-150, 2017 F-SUPER DUTY VEHICLES MAY HAVE CONCERNS WHERE THE INSTRUMENT CLUSTER DEFAULTS BACK TO THE TRAILER TOW SETUP SCREEN EVERY KEY CYCLE WITH NO TRAILER ATTACHED. REFER TO THE INFORMATION DISPLAY SECTION OF THE OWNERS MANUAL OR THE FOLLOWING STEPS TO CORRECT THIS CONCERN. TYPE 1 AND 2 CLUSTER SMALL DISPLAY USE THE INFORMATION DISPLAY CONTROLS ON THE STEERING WHEEL AND THE INFORMATION DISPLAY MENU. NAVIGATE TO TOWING AND PRESS OK, SELECT TRAILER OPTIONS AND PRESS OK, CHOOSE SELECT TRAILER AND PRESS OK, FINALLY SELECT NO ACTIVE TRAILER AND PRESS OK. TYPE 3 CLUSTER LARGE DISPLAY USE THE INFORMATION DISPLAY CONTROLS ON THE STEERING WHEEL AND THE INFORMATION DISPLAY MENU. NAVIGATE TO TOWING TAB, SELECT TRAILER SETUP AND PRESS OK, THEN PRESS OK TO ENTER TRAILER OPTIONS, SELECT CHANGE TRAILER SELECTED AND PRESS OK, FINALLY SELECT NO ACTIVE TRAILER AND PRESS OK.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2015-2016 F-150 SUPERCREW VEHICLES EQUIPPED WITH THE VISTA ROOF OPENING PANEL MAY EXHIBIT A WATER LEAK FROM THE ROOF OPENING PANEL AREA. REFER TO WORKSHOP MANUAL (WSM) SECTION 501-17 FOR WATER LEAK DIAGNOSIS. IF TEST RESULTS LEAD TO REPLACEMENT OF ROOF OPENING PANEL GLASS INSTALL PART NUMBER FL3Z-16500A18-E WHICH HAS A REVISED SEAL. USE CASUAL PART 16500A18 AND APPLICABLE LABOR OPERATIONS IN SECTION 12 OF THE SERVICE LABOR TIME STANDARDS (SLTS) MANUAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2015 EDGE,MUSTANG AND F150 VEHICLES WITH A 4" DISPLAY MAY EXHIBIT A 24 HOUR CLOCK DISPLAY THAT RESETS ITSELF TO A 12 HOUR DISPLAY AFTER CYCLING THE IGNITION KEY. TO CORRECT THE CONCERN, REFLASH THE FRONT CONTROL DISPLAY INTERFACE MODULE (FCDIM) TO THE LATEST CALIBRATION USING IDS VERSION 103.05 OR HIGHER. MAKE SURE YOU ARE CONNECTED TO THE INTERNET WHEN ENTERING MODULE PROGRAMMING TO OBTAIN THE LATEST UPDATES. CALIBRATION FILES MAY ALSO BE OBTAINED AT WWW.MOTORCRAFTSERVICE.COM. USE CAUSAL COMPONENT 10D885 AND APPLICABLE 12652A LABOR OPERATIONS FROM SECTION 10 OF THE SLTS MANUAL FOR REFLASH ONLY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2015-2017 F-150 XL VEHICLES ARE BUILT WITH FRONT SEAT BRACKET SHIELDS AND BOLT CAPS ON THE FRONT AND REAR OF THE INBOARD SEAT BRACKETS ONLY. THE OUTBOARD SEAT BRACKETS DO NOT HAVE SHIELDS OR BOLT CAPS INSTALLED FROM THE FACTORY. INSTALLING NEW SHIELDS AND BOLT CAPS ON THE FRONT OR REAR OF THE OUTBOARD SEAT BRACKETS IS NOT A WARRANTABLE REPAIR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
WHEN SERVICING A 2.7L OR 3.0L ECOBOOST ENGINE, IF THE CRANKSHAFT PULLEY IS REMOVED, CORRECT REASSEMBLY IS CRITICAL TO PREVENT POTENTIAL ENGINE FAILURE. THIS INCLUDES INSTALLING A NEW CRANKSHAFT PULLEY BOLT AND ACCURATELY PERFORMING EACH STAGE OF THE CRANKSHAFT PULLEY BOLT TORQUE SEQUENCE. CRANKSHAFT PULLEY RELATED WORKSHOP MANUAL (WSM) PROCEDURE AND RECOMMENDED TOOL (OTC 4754 OR EQUIVALENT) INFORMATION HAVE BEEN UPDATED. REFER TO THE APPLICABLE WSM, SECTION 303-01, FOR ADDITIONAL INFORMATION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2015-2016 F-150 VEHICLES EQUIPPED WITH A 5.0L ENGINE MAY EXHIBIT A HARD START, CRANK NO START, RUNS ROUGH AND/OR BLACK EXHAUST SMOKE CONCERN ASSOCIATED WITH BLOCK HEATER OPERATION IN COLD AMBIENT TEMPERATURES BELOW -18 CELSIUS (0 FAHRENHEIT). FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TO HELP DIFFERENTIATE ENGINE OIL LEAKS FROM OTHER POSSIBLE SOURCES, A NEW WHITE-COLORED FLUORESCENT ENGINE OIL DYE IS AVAILABLE. WORKSHOP MANUAL (WSM), SECTION 303-00 HAS BEEN REVISED TO REFERENCE THE NEW WHITE-COLORED DYE. THE NEW WHITE FLUORESCENT DYE PROVIDES A DISTINCT WHITE GLOW TO IDENTIFY ENGINE OIL LEAKS. THE NEW WHITE FLUORESCENT DYE REQUIRES A PURE UV DIAGNOSTIC INSPECTION LAMP. THE WHITE-COLORED FLUORESCENT DYE AND PURE UV LAMP ARE NOW IN THE ROTUNDA CATALOG. DYE AND LAMP PART NUMBERS. GASOLINE ONLY DYE: 1 OUNCE BOTTLE 164-TP-33200601. DIESEL ONLY DYE: 8 OUNCE BOTTLE: 164-TP-3320-0008. PURE UV DIAGNOSTIC INSPECTION LAMP 164-TP8695 OR 164-R3748.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2015-2017 F-150 VEHICLES BUILT ON OR BEFORE 28-NOV-2016 EQUIPPED WITH A MECHANICAL TAILGATE HANDLE AND REMOTE CONTROL TAILGATE LOCK MAY EXHIBIT A TAILGATE THAT WILL NOT OPEN DURING FREEZING TEMPERATURES DUE TO A FROZEN TAILGATE LATCH CONTROL ASSEMBLY. TO CORRECT THIS CONCERN INSTALL A REVISED TAILGATE LATCH CONTROL ASSEMBLY PART NUMBER FL3Z-9943170-E. REFER TO WORKSHOP MANUAL SECTION 501-14. FOR CLAIMING, USE CAUSAL PART 9943170 AND APPLICABLE LABOR OPERATIONS IN SECTION 12 OF THE SERVICE LABOR TIME STANDARDS (SLTS) MANUAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2015-2017 F-150 SUPERCAB VEHICLES MAY EXHIBIT INOPERATIVE REAR DOOR LOWER LATCHES DURING FREEZING TEMPERATURES. THE REAR DOOR LOWER LATCHES HAVE BEEN REVISED TO INCLUDE A WATER SHIELD AND THE PARTS CATALOG HAS BEEN UPDATED TO SHOW THE NEW NUMBERS. REPLACE THE REAR DOOR LOWER LATCHES, REFER TO WORKSHOP MANUAL (WSM), SECTION 501-14. FOR CLAIMING, USE CAUSAL PART 18264A00 AND APPLICABLE LABOR OPERATIONS IN SECTION 12 OF THE SERVICE LABOR TIME STANDARDS (SLTS) MANUAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2015-2016 EDGE WITH 2.0L GASOLINE TURBOCHARGED DIRECT INJECTION (GTDI), 2015-2016 MUSTANG AND F-150 WITH 5.0L ENGINE AND 2016 EXPLORER EQUIPPED WITH 2.3L GTDI ENGINE MAY EXHIBIT OIL LEAK AT ENGINE OIL PRESSURE (EOP) SENSOR THREADS. IT IS NOT REQUIRED TO REPLACE THE SENSOR IF IT IS LEAKING FROM THE THREADS. REMOVE AND RESEAL THE EOP SENSOR, REFER TO WORKSHOP MANUAL (WSM), SECTIONS 303-14. CHECK THE OIL LEVEL AND TOP OFF AS NECESSARY. REFER TO WSM, SECTION 303-01. USE CAUSAL PART 9278 AND APPLICABLE LABOR OPERATIONS IN SECTION 09 OF THE SERVICE LABOR TIME STANDARDS (SLTS) MANUAL
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2015-2017 F-150 VEHICLES MAY EXHIBIT INOPERATIVE LATCHES ON FRONT DOORS AND/OR SUPERCREW REAR DOORS DURING FREEZING TEMPERATURES. FOLLOW THE TSB SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2010-2016 EPAS EQUIPPED VEHICLES MAY EXHIBIT STEERING RELATED NOISES. THE WORKSHOP MANUAL (WSM) DIAGNOSTIC PROCEDURES HAVE BEEN UPDATED IN SECTION 211-02. WHEN DIAGNOSING AND REPAIRING EPAS STEERING NOISES USE THE UPDATED PROCEDURES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2015-2017 F-150, 2016 MKX, 2015 EDGE, 2017 FUSION, MKZ AND CONTINENTAL VEHICLES EQUIPPED WITH A 2.7L/3.0L ENGINE MAY APPEAR TO HAVE LOW ENGINE OIL LEVEL IF THE PROPER PROCEDURES ARE NOT FOLLOWED. REFER TO THE OWNERS GUIDE, MAINTENANCE, ENGINE OIL CHECK SECTION. WHEN CHECKING THE ENGINE OIL LEVEL AFTER SHUTTING OFF THE ENGINE WAIT AT LEAST 15 MINUTES PRIOR TO CHECKING IN ORDER TO ALLOW THE OIL TO DRAIN BACK TO THE OIL PAN. THE ENGINE OIL LEVEL CAN BE CHECKED IMMEDIATELY IF THE ENGINE HAS NOT BEEN STARTED. WHEN CHANGING THE ENGINE OIL THE ENGINE NEEDS TO BE AT NORMAL OPERATING TEMPERATURE AND THE OIL FILTER REMOVED BEFORE DRAINING THE OIL. ALLOW THE OIL PAN TO DRAIN COMPLETELY FOR UP TO 5 MINUTES. CHECK OIL LEVEL AFTER FILLING BY FOLLOWING THE OIL LEVEL CHECK PROCEDURE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
CERTAIN 2015 MODEL YEAR EDGE, 2015-2016 MODEL YEAR F-150, MKT, AND POLICE INTERCEPTOR SEDAN, AND 2016 MODEL YEAR ESCAPE, EXPLORER, FLEX, FUSION, MKX, MUSTANG, POLICE INTERCEPTOR UTILITY, TAURUS, AND TRANSIT VEHICLES - ELECTRONIC THROTTLE BODY REPLACEMENT
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2015-2017 F-150 VEHICLES MAY EXHIBIT POOR HEATER PERFORMANCE CAUSED BY RESTRICTED HEATER CORES. EXTENSIVE USE OF THE BLOCK HEATER MAY INCREASE COOLING SYSTEM DEPOSITS WHICH CONTRIBUTE TO HEATER CORE RESTRICTIONS. IT IS RECOMMENDED TO PLUG IN THE BLOCK HEATER FOR 1 2 HOURS BEFORE STARTING ENGINE WHEN AMBIENT TEMPERATURES ARE -15 DEGREES C (0 DEGREES F) OR LOWER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2015-2016 F-150 VEHICLES MAY EXPERIENCE INTERMITTENT LOSS OF THROTTLE PEDAL RESPONSE, ILLUMINATED WRENCH, HILL DESCENT, AIRBAG, ANTI LOCK BRAKE SYSTEM(ABS) AND/OR ADVANCED TRAC WARNING INDICATORS AND/OR P2122, P2123, P2124, P2125, P2127, P2128 AND/OR P2138 DTCS. THIS MAY BE CAUSED BY THE ACCELERATOR PEDAL POSITION (APP) SENSOR 14A005 HARNESS BEING IMPROPERLY ROUTED BEHIND THE BRAKE BOOSTER TO BRAKE PEDAL BRACKET. IF THE HARNESS IS IMPROPERLY ROUTED, LOOSEN THE BRACKET TO FREE THE HARNESS. INSPECT AND REPAIR DAMAGED CIRCUITS BEFORE PROPERLY ROUTING THE HARNESS. IF THE HARNESS IS PROPERLY ROUTED, PROCEED WITH NORMAL DIAGNOSTICS IN THE WORKSHOP MANUAL (WSM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
WHEN HOOKING UP THE VEHICLE COMMUNICATION MODULE (VCM) AND INTEGRATED DIAGNOSTIC SYSTEM (IDS) TO THE DLC LOCATED ON THE DRIVER SIDE UNDER THE STEERING COLUMN AT THE GWM, MAKE SURE THAT THE IGNITION IS OFF BEFORE CONNECTING TO IDS. IF THE IGNITION IS ON OR THE ENGINE IS RUNNING DURING THE HOOK UP, IT CAN RESULT IN VARIOUS WARNING LIGHTS BEING ILLUMINATED WITH DIAGNOSTIC TROUBLE CODES (DTCS), NO START OR NO CRANK CONDITIONS OR THE CLUSTER INOPERATIVE. FOR LINCOLN VEHICLES, THIS INFORMATION IS NOW LISTED IN THE TECHNICAL INSPECTION AND POST ROAD TEST SECTIONS OF EPDI ON THE PTS WEBSITE. IF A VEHICLE DISPLAYS THESE ISSUES, DISCONNECT THE EQUIPMENT FROM THE DLC AND REINSTALL WITH THE IGNITION OFF. CLEAR ANY DTCS PRESENT AND RETEST.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2015-2016 F-150, C-MAX, EDGE, MKS, TAURUS, AND FLEX AND 2016 EXPEDITION, EXPLORER, ESCAPE, FUSION, MUSTANG, MKZ, MKX, NAVIGATOR, TRANSIT AND TRANSIT CONNECT VEHICLES EQUIPPED WITH A 2.0L, 2.5L, 3.5L OR 3.7L GASOLINE ENGINE AND BUILT ON OR BEFORE 31-MAY-2016 MAY EXHIBIT AN INTERMITTENT LOSS OF POWER AND/OR AN ILLUMINATED POWERTRAIN MALFUNCTION (WRENCH) LAMP WITH DIAGNOSTIC TROUBLE CODES (DTCS) P2111, P2112 AND/OR P2119 STORED IN POWERTRAIN CONTROL MODULE (PCM) MEMORY. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may have a concern where the safety belt retractor webbing does not extract from the stowed position or exhibits excessive pressure on the occupant during use. This may be due to a normal condition which happens when the seatbelt retracts at a high rate of speed. The Workshop Manual, Section 501-20A General Procedures has been updated with a locked seatbelt retractor releasing procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The Powertrain Control/Emissions Diagnosis (PC/ED) manual has been revised for diagnosing electronic throttle bodies (ETBs). The ETC_ACT and ETC_DSD PIDs should not used to diagnose possible ETB concerns. The IDS has a limited refresh rate when reading these PIDs and cannot display quickly enough to validate a concern. The PCM automatically monitors these inputs more accurately and will set diagnostic trouble codes (DTCs) when appropriate. Using these PIDs for diagnostics will lead to inaccurate results and improper ETB replacements. If a concern is intermittent and no DTCs are present, refer to historical DTCs and the PC/ED, Section 3 No DTCs Present Index chart for further information.
Source components: ENGINE · ENGINE AND ENGINE COOLING · ENGINE AND ENGINE COOLING:COOLING SYSTEM · ENGINE AND ENGINE COOLING:COOLING SYSTEM:FAN · ENGINE AND ENGINE COOLING:COOLING SYSTEM:HOSES/LINES/PIPING/FITTINGS · ENGINE AND ENGINE COOLING:COOLING SYSTEM:RADIATOR ASSEMBLY · ENGINE AND ENGINE COOLING:ENGINE · ENGINE AND ENGINE COOLING:ENGINE:DIESEL · ENGINE AND ENGINE COOLING:ENGINE:GASOLINE · ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:BELTS AND ASSOCIATED PULLEYS · ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER · ENGINE AND ENGINE COOLING:ENGINE:OTHER FUEL TYPES:TURBO/SUPERCHARGER · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV) · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:GAS RECIRCULATION VALVE (EGR VALVE) · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2016 F-150 vehicles may exhibit a vibration on acceleration or cruise that is originating from the driveshaft and/or rear axle. During preliminary inspection look for visible driveshaft damage, alignment of the axle pinion flange to driveshaft flange yellow dots, and that the rear driveshaft flange sits flat on the axle pinion flange. If no issues are found, refer to workshop manual section 205-01 to continue with driveshaft diagnosis and testing.
Source components: EQUIPMENT · POWER TRAIN · SUSPENSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2015 Model Year Edge, 2015-2016 Model Year F-150, MKT, and Police Interceptor Sedan, and 2016 Model Year Escape, Explorer, Flex, Fusion, MKX, Mustang, Police Interceptor Utility, Taurus, and Transit Vehicles - Electronic Throttle Body Repair
NHTSA source summary · Original PDF not reviewed by Recallfolio
WHEN HOOKING UP THE VEHICLE COMMUNICATION MODULE (VCM) AND INTEGRATED DIAGNOSTIC SYSTEM (IDS) TO THE DLC LOCATED ON THE DRIVER SIDE UNDER THE STEERING COLUMN AT THE GWM, MAKE SURE THAT THE IGNITION IS OFF BEFORE CONNECTING TO IDS. IF THE IGNITION IS ON OR THE ENGINE IS RUNNING DURING THE HOOK UP, IT CAN RESULT IN VARIOUS WARNING LIGHTS BEING ILLUMINATED WITH DIAGNOSTIC TROUBLE CODES (DTCS), NO START OR NO CRANK CONDITIONS OR THE CLUSTER INOPERATIVE. FOR LINCOLN VEHICLES, THIS INFORMATION IS NOW LISTED IN THE TECHNICAL INSPECTION AND POST ROAD TEST SECTIONS OF EPDI ON THE PTS WEBSITE. IF A VEHICLE DISPLAYS THESE ISSUES, DISCONNECT THE EQUIPMENT FROM THE DLC AND REINSTALL WITH THE IGNITION OFF. CLEAR ANY DTCS PRESENT AND RETEST.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2015-2016 F-150 VEHICLES EQUIPPED WITH ADAPTIVE CRUISE CONTROL MAY EXHIBIT A COLLISION WARNING MALFUNCTION AND/OR ADAPTIVE CRUISE MALFUNCTION MESSAGE IN THE INSTRUMENT CLUSTER MESSAGE CENTER WITH DIAGNOSTIC TROUBLE CODES (DTC) B142E:78 AND/OR U3000:49 IN THE CRUISE CONTROL MODULE (CCM). TO CORRECT THIS CONDITION, UPDATE THE CCM TO THE LATEST CALIBRATION LEVEL USING INTEGRATED DIAGNOSTIC SYSTEM (IDS) VERSION 101.03 OR HIGHER. REFER TO WORKSHOP MANUAL (WSM) SECTION 419-03B TO PERFORM THE CRUISE CONTROL RADAR ALIGNMENT PROCEDURE. MAKE SURE YOU ARE CONNECTED TO THE INTERNET WHEN ENTERING MODULE PROGRAMMING TO OBTAIN THE LATEST UPDATES. CALIBRATION FILES MAY ALSO BE OBTAINED AT WWW.MOTORCRAFTSERVICE.COM. USE CAUSAL PART 9E731 AND APPLICABLE LABOR OPERATIONS IN SECTION 10 OF THE SERVICE LABOR TIME STANDARDS (SLTS) MANUAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2015-2016 F-150 VEHICLES BUILT ON OR BEFORE 9/24/2015 MAY EXHIBIT A DRIFT, PULL, AND/OR WANDER CONCERN. TO ADDRESS THE CONCERN, REPROGRAM THE POWER STEERING CONTROL MODULE (PSCM) TO THE LATEST LEVEL USING IDS VERSION 101.04 OR HIGHER AND ATTEMPT TO RE-VERIFY THE CUSTOMER CONCERN. IF THE CUSTOMER CONCERN IS STILL PRESENT, THEN CONTINUE WITH NORMAL WSM DIAGNOSTICS. THE UPDATED CALIBRATION HAS IMPROVEMENTS TO THE ELECTRONIC POWER ASSIST STEERING (EPAS) COMPENSATION. MAKE SURE YOU ARE CONNECTED TO THE INTERNET WHEN ENTERING MODULE PROGRAMMING TO OBTAIN THE LATEST UPDATES. CALIBRATION FILES MAY ALSO BE OBTAINED AT WWW.MOTORCRAFTSERVICE.COM. USE CAUSAL COMPONENT 3504 AND APPLICABLE 3504E LABOR OPERATIONS FROM SECTION 3 OF THE SLTS MANUAL FOR REPROGRAM ONLY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SOME 2015-2016 F-150 VEHICLES EQUIPPED WITH A FL3Z-16C900-A (SMOKE) OR FL3Z-16C900-B (CHROME), GENUINE FORD AUTHORIZED ACCESSORY (GFAA) HOOD/BUG DEFLECTOR KIT, MAY EXHIBIT A RATTLE NOISE, VIBRATION, OR LOOSENESS AT THE DEFLECTOR. A NEW HARDWARE KIT (GL3Z-99000A25-B) IS NOW AVAILABLE WHICH IMPROVES INSTALLATION AND REDUCES NOISE, VIBRATIONS AND LOOSENESS.