2022 Ford EXPLORER Manufacturer communications & TSBs.Page 2
Original record summaries, dates and identifiers for this model-year. Records 101–200 of 230, ordered newest first. Dated records on this page: May 11, 2022–Feb 29, 2024.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Feb 29, 2024Service Bulletin/Repair Instructions
SSM 52307
NHTSA communication ID: 10250852
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2023 Ford and Lincoln SYNC3 equipped vehicles may experience an inaccurate notification in the FordPassî/LincolnWayî app indicating Vehicle Has Entered Deep Sleep Mode. Vehicle Has Entered Deep Sleep Mode message is expected if the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SoC) drops below 50%. If the vehicle is going into deep sleep due to one of these conditions, follow normal Workshop Manual (WSM) Section 414-01 procedure to correct the concern. If the vehicle is going into deep sleep outside these conditions, this may be due to the telematics control unit (TCU) software. To correct this condition, follow the Service Procedure to update the TCU to the latest software. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 23-2181 to add 2024 vehicle model year. Some 2020-2024 Explorer/Aviator vehicles may exhibit a lack of audio and/or a water leak in the rear liftgate area and/or water in the spare tire area. The customer may indicate that this concern is more noticeable after a car wash or rainfall. To correct the condition, follow the Service Procedure to identify the leak path.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 23-2208 to add 2024 model year vehicles. Some 2020-2024 Explorer/Aviator non-hybrid vehicles may exhibit radio static and/or poor radio sound quality when moving. This may be more noticeable on AM radio stations. This may be caused by an electromagnetic interference concern
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
NHTSA source summary · Original PDF not reviewed by Recallfolio
2022-2024 Explorer/Aviator vehicles built on or after 28-May-2022, 2022-2024 Expedition/Navigator vehicles built on or after 08-Jun-2022, 2022-2024 Escape vehicles built on or after 01-Jun-2022 and 2022 Corsair vehicles built on or after 01-Jun-2022 are no longer equipped with a hands free liftgate system. The vehicle is not misbuilt. The addition of any parts is not a warrantable repair. Do not submit a claim for this condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2024 Explorer/Aviator vehicles may exhibit poor speaker sound quality and/or tick-tock noise while activating turn signals and streaming audio over Bluetooth. Customers may describe static heard during a Bluetooth phone call or a door speaker buzz or tick noise with the pulse of the turn signal. This may be due to concerns with the 14401/14A005 wiring harnesses or connector damage. Prior to the replacement of the affected speaker, inspect for incorrect pin fit/crimp, bent pins, broken wire strands, or other damage at inline connectors C202, C2383A, and/or C4240B. These circuits join the accessory protocol interface module (APIM) and audio front control module (ACM) components. If wiring/connector concerns are found, repair per Wiring Diagram Cell 5.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2023 Explorer/Aviator vehicles equipped with all-wheel drive (AWD) may exhibit an illuminated powertrain malfunction (wrench) indicator and/or 4WD Fault Service Required message with diagnostic trouble codes (DTCs) C00A6:71, C00A6:74, C00A6:99, C00A7:11, C00A7:13, C00A8:11, and/or C00A8:13 present in the AWD module. This may be due to a damaged wiring harness rubbing against the underbody heat shield where it routes over and into the transfer case actuator motor. Inspect the wire harness for damage and repair as necessary following the procedures in the Wiring Diagram Manual. If no damage is found, continue with normal diagnostics.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 F-150, 2022-2023 Expedition/Navigator, 2022-2023 Mustang, 2020-2023 Transit, 2020-2023 Explorer/Aviator vehicles equipped with a 10R80/10R80MHT transmission may exhibit a harsh/delayed engagement and/or harsh/delayed shift, an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes. stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to the software in the powertrain control module (PCM) or transmission control module (TCM), the transmission solenoid ID strategy, sticking valves in the main control valve body and/or axial movement of the CDF clutch cylinder (7H351) sleeve.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2023 Explorer vehicles equipped with a 2.3L EcoBoost engine, 2022-2023 F-150 vehicles equipped with a 3.5L EcoBoost engine, and 2023-2024 Expedition/Navigator vehicles may exhibit an illuminated malfunction indicator lamp (MIL) and/or powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTCs) P25B3, P25B4, P25B5, P25B6, P2ABA, P2ABB, P2ABC, P2AB7, P2AB8, and/or P2AB9. This may be due to the software in the powertrain control module (PCM). To correct this condition, follow the Service Procedure to reprogram the PCM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2023 Explorer/Aviator and 2021-2023 Bronco vehicles equipped with a 10R60 transmission may exhibit a harsh/delayed engagement and/or harsh/delayed shift, an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to the software in the powertrain control module (PCM) or transmission control module (TCM), the transmission solenoid ID strategy and/or sticking valves in the main control valve body. To correct the condition, follow the Service Procedure to identify and correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022-2023 Explorer vehicles with 2.3L engine built on or before 20-Jul-2023 may exhibit an intermittent malfunction indicator light (MIL) with diagnostic trouble code (DTC) P1026 and/or P1299 present in the powertrain control module (PCM) and an engine over-temperature message displayed on the instrument panel cluster (IPC) after a cold engine start. The vehicle will also exhibit reduced performance when it enters fail safe cooling open loop mode. If the engine is not overheating, clear the DTCs to reset the fail safe cooling open loop mode. Start and idle the engine while viewing coolant flow at the top inner (engine side) degas bottle hose port through the semitransparent top. If there is no coolant flow, replace the L1MZ-8A365-AAD engine-to-degas bottle hose. If if there is any coolant flow, return to Workshop Manual (WSM), Section 303-03A diagnostics.
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Mustang/Ranger/Transit Connect, 2020-2021 EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator, 2021 Bronco Sport and 2020-2022 Explorer/Aviator vehicles with SYNC 3 may experience various SYNC performance related concerns. This may be due to the SYNC Software. To correct the condition, follow the Service Procedure to update the SYNC module (APIM) software.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2023 Explorer/Aviator vehicles equipped with a 10R80 MHT transmission may exhibit an illuminated powertrain malfunction (wrench) lamp with diagnostic trouble code (DTC) P084B stored in the PCM. The Workshop Manual (WSM) has recently been updated to provide new direction for DTC P084B.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022-2023 Explorer vehicles built on or before 01-Jun-2023 may exhibit a buzz/vibration/rattle from the center left of the IP during tip-in when the vehicle is up to operating temperature. This may be due to heater tube movement against the tube bracket.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2023 Ford and Lincoln vehicles equipped with a 10R60/10R80/10R80 MHT/10R100 transmission may exhibit a whine noise at idle and/or while driving. This may be identified as coming from the bellhousing and the front of the transmission fluid pan. The whine noise may become louder when the transmission is at operating temperature and may increase with engine revolutions per minute (RPM) in the park (P) position. A small amount of whine noise is considered to be characteristic of the 10R60/10R80/10R80 MHT/10R100 transmissions due to the offset gear drivetrain in the front support and has no effect on durability. Use the Report a Vehicle Concern link at the bottom of OASIS to submit a report if there is a customer concern of whine noise describing operating conditions and noise severity.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles equipped with power folding mirrors may exhibit power folding mirrors that are inoperative or exhibit a clicking sound. This may be due to the mirrors being manually folded in, during transportation, going through a car wash, bumped in a parking lot, or found during pre-delivery inspection (PDI). Prior to the replacement of any components, attempt to synchronize the mirrors by following the Power Mirrors Synchronization procedure. Refer to Workshop Manual (WSM) Section 501-09 Rear View Mirrors - General Procedures - Power Mirrors Synchronization.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2023 Explorer/Aviator all-wheel drive (AWD) vehicles with a hybrid powertrain may experience a harshness and/or vibration felt through the seat, steering wheel and/or center console at 25-50 mph (40-80 km/h). This may be due to constant velocity (CV) joint instability at dynamic angles close to zero. To correct the condition, follow the Service Procedure to install a driveline shim.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022 Edge vehicles built on and after 16-Nov-2022, 2022 Explorer vehicles built on and after 20-Sep-2022, 2023 Edge vehicles built on and before 24-Mar-2023, and 2023 Explorer vehicles built on and before 06-Mar-2023 may exhibit a brief illumination of the malfunction indicator lamp (MIL) when the vehicle is shifted into park (P) with diagnostic trouble code (DTC) P0919 and/or P0929 stored in the gear shift module (GSM). This may be due to the GSM software. To correct this condition, update the software in the GSM using the latest software level of the Ford Diagnosis and Repair System (FDRS).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022 Explorer/Aviator vehicles may exhibit an intermittent passenger seat massage function with no diagnostic trouble codes (DTCs). This may be due to the configuration of the seat control module G (SCMG) and seat control module H (SCMH) modules. To correct the condition, reprogram the SCMG and SCMH and run the SCMG and SCMH configuration application with the latest software level of the Ford Diagnosis and Repair System (FDRS). For claiming, use causal part 14F548 and applicable labor times found in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Aviator/Explorer Hybrid vehicles may exhibit a concern where the EV power flow does not display in the center display screen. This may be due to the SYNC module (APIM) software. Download and run the APIM-SYNC Module (APIM) Standard Programming application using the latest software level of the Ford Diagnosis and Repair System (FDRS). After programming the APIM to the latest level, the EV power flow screen may intermittently not function under certain conditions. No further repair procedure is recommended as this function is not critical to the operation of the hybrid powertrain system. For claiming, use causal part 14G371 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 F-150 vehicles equipped with a 3.5L hybrid engine, 2020-2023 Explorer vehicles equipped with a 3.3L hybrid engine and 2020-2023 Aviator vehicles equipped with a 3.0L hybrid engine may exhibit a powertrain malfunction indicator lamp with diagnostic trouble code (DTC) P0A1E stored in the powertrain control module (PCM). This may be due to the belt integrated starter generator (BISG). To correct this condition, follow the Service Procedure to diagnose and repair this symptom.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2020-2023 Explorer non-hybrid vehicles and equipped with a 3.0L EcoBoost or 3.3L Duratec engine and 2020-2023 Aviator non-hybrid vehicles equipped with a 3.0L EcoBoost engine built on or before 01-Jan-2023 may exhibit an exhaust rattle requiring replacement of the left or right exhaust flexible pipe (5G203). The updated part locates the flexible joint portion of the pipe closer toward the catalytic converter than the originally equipped part. This is due to a design change with these replacement components which will not cause any functional issues with the vehicle.
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 22-2428 and 23-2176 to update the Issue, Action and Service Procedure. Some 2017-2023 F-150, 2018-2023 Expedition/Navigator/Mustang, 2019-2023 Ranger, 2020-2023 Explorer/Aviator/Transit and 2021-2023 Bronco vehicles equipped with a 10R60/10R80/10R80MHT transmission may exhibit a harsh/delayed engagement and/or harsh/delayed shift, an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to the software in the powertrain control module (PCM) or transmission control module (TCM), the transmission solenoid ID strategy, sticking valves in the main control valve body and/or axial movement of the CDF clutch cylinder (7H351) sleeve. To correct the condition, follow the Service Procedure to identify and correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2023 Explorer vehicles may exhibit a condition of intermittent headlamp operation while the vehicle is OFF and have diagnostic trouble code (DTC) B1533 stored in the body control module (BCM). This may be due to the internal logic within the headlamp switch. To correct this condition, replace the headlamp switch (service base PN: 11654). Refer Workshop Manual, Section 417-01.
Source components: ELECTRICAL SYSTEM · EXTERIOR LIGHTING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
In various 2017-2023 Ford and Lincoln vehicles, customers may receive a message in the FordPass or LincolnWay App stating Feature Unavailable. Since this is a fleet vehicle, it cannot access the (SYNC Connect) FordPass or LincolnWay app through the TCU Embedded Modem. If this message appears, the vehicle may be equipped with a fleet telematics module. Replacement of the TCU or TCU related repairs will not prevent this message from appearing. Refer the customer to in app FordPass Guides or LincolnWay Concierge Teams to aid with fleet telematics removal. Open app, select Account > Help > CHAT or CALL option.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2020-2023 Explorer non-hybrid vehicles equipped with a 3.0L EcoBoost or 3.3L Duratec engine and 2020-2023 Aviator non-hybrid vehicles equipped with a 3.0L EcoBoost engine may exhibit an exhaust rattle requiring replacement of the left or right exhaust flexible pipe (5G203). The updated part locates the flexible joint portion of the pipe closer toward the catalytic converter than the originally equipped part. This is due to a design change with these replacement components which will not cause any functional issues with the vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022 Explorer vehicles equipped with a 3.3L full hybrid electric vehicle (FHEV) engine and built on 12-Jul-2022 and through 31-Oct-2022 may exhibit a coolant leak at the high voltage (HV) battery coolant cooler outlet hose. This may be due to the HV battery coolant cooler outlet hose contacting the bottom pulley of the accessory drive belt tensioner. To correct the condition, follow the Service Procedure to replace the damaged hose and install a cable tie.
Source components: ELECTRICAL SYSTEM · HYBRID PROPULSION SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2023 Explorer/Aviator vehicles may exhibit poor speaker sound quality and/or tick-tock noise while activating turn signals and streaming audio over Bluetooth. Customers may describe static heard during a Bluetooth phone call, or a door speaker buzz or tick noise with the pulse of the turn signal. This may be due to concerns with the 14401/14A005 wiring harnesses or connector damage. Prior to the replacement of the affected speaker, inspect for incorrect pin fit/crimp, bent pins, broken wire strands, or other damage at inline connectors C202, C2383A, and/or C4240B. These circuits join the SYNC module (APIM) and audio front control module (ACM) components. If wiring/connector concerns are found, repair per Wiring Diagram Cell 5.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:ELECTRICAL:INFOTAINMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2023 Explorer/Aviator non-hybrid vehicles may exhibit radio static and/or poor radio sound quality when moving. This may be more noticeable on AM radio stations. This may be caused by an electromagnetic interference concern. To correct the condition, follow the Service Procedure to install new grounds on the rear knuckle.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC..
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2023 Explorer/Aviator vehicles equipped with a 3.0L EcoBoost may exhibit an illuminated malfunction indicator lamp (MIL) and low oil pressure warning in the instrument panel cluster (IPC), with diagnostic trouble codes (DTC) P0521 and/or P0524 in the powertrain control module (PCM). This condition may be caused by an internal oil pressure leak. If pinpoint test E in the Workshop Manual (WSM) Section 303-01B directs you to the replacement of the oil pump, upon reassembly inspect that the main oil gallery tube (6718) is assembled and aligned properly on the back of the engine front cover. The engine oil gallery seal (00815) must be replaced any time the front cover is removed (per WSM Section 303-01B). The WSM front cover removal and installation procedure is in the process of being updated.
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022-2023 Explorer vehicles equipped with a 2.3L engine may exhibit an intermittent malfunction indicator light (MIL) with diagnostic trouble code (DTC) P1026 and/or P1299 present in the powertrain control module (PCM) and an engine over-temperature message displayed on the instrument panel cluster (IPC) after a cold engine start. The vehicle will also exhibit reduced performance when it enters fail safe cooling open loop mode. If the engine is not overheating, clear the DTCs to reset the fail safe cooling open loop mode. Start and idle the engine while viewing coolant flow at the top inner (engine side) degas bottle hose port through the semitransparent top. If there is no coolant flow, replace the L1MZ-8A365-AAD engine-to-degas bottle hose. If if there is any coolant flow, return to Workshop Manual (WSM), Section 303-03A diagnostics.
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2023 Explorer/Aviator vehicles may exhibit a lack of audio and/or a water leak in the rear liftgate area and/or water in the spare tire area. The customer may indicate that this concern is more noticeable after a car wash or rainfall. To correct the condition, follow the Service Procedure to identify the leak path.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2023 Ford and Lincoln SYNC3 equipped vehicles may experience an inaccurate notification in the FordPass®/LincolnWay® app indicating Vehicle Has Entered Deep Sleep Mode. Vehicle Has Entered Deep Sleep Mode message is expected if the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SoC) drops below 50%. If the vehicle is going into deep sleep outside these conditions, this may be due to the telematics control unit (TCU) software. To correct this condition, follow the Service Procedure to update the TCU to the latest software. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022 Edge vehicles built on and after 16-Nov-2022 and 2022 Explorer vehicles built on and after 20-Sep-2022 may exhibit a brief illumination of the malfunction indicator lamp (MIL) when the vehicle is shifted into park (P) with diagnostic trouble code (DTC) P0919 and/or P0929 stored in the gear shift module (GSM). This may be due to the GSM software. To correct this condition, update the software in the GSM using the latest software level of the Ford Diagnosis and Repair System (FDRS). For claiming use the causal part number 7P155 and applicable labor operations in Section 07 of the Service Labor Time Standards (SLTS).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2023 Explorer/Aviator vehicles may have a concern where the second row outboard manual/power seats do not fold, exhibit excess effort to fold, or do not slide forward/backward easily. Power or manual second row seats must be pushed forward manually during easy entry function since the assist spring will reduce but not eliminate manual effort. Refer to the Owner's Manual > Seats > Rear Seats > Adjusting the Second Row Rear Seats for further details. If the seats do not easily push forward manually, it maybe due to tension in the seat track due to uneven assembly torque. To correct these conditions, unbolt the second row seat frame from the floor to relax tension. Start the bolts by hand, then tighten in the correct sequence and torque per Workshop Manual (WSM) Section 501-10B.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2023 Aviator/Explorer vehicles equipped with a 3.0L hybrid engine may exhibit illuminated powertrain malfunction (wrench) indicator and stop safely now warning. Diagnostic trouble code (DTC) P0AA6:00 may be stored in the battery energy control module (BECM). Inspect the right side frame rail area near the bank 1 charge air cooler (CAC) intake pipe clamp for chafing the orange high voltage harness. If the harness is damaged, de-energize high voltage system per Workshop Manual (WSM), Section 414-03A. Reposition the clamp and replace the high voltage harness (14290). If the harness is not damaged continue P0AA6 diagnostics in WSM, Section 414-03A, Pinpoint Test T. For a P0AA6 diagnostic aid video, refer to Professional Technician System (PTS) > Home > Technical Assistance > Technical Support Videos > enter P0AA6 in search box and click video returned.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The Service Awareness Newsletter is an informal communication that contains information that may not be presently available in a TSB, SSM, GSB, or other electronic communication. This article includes information on warranty, technical service tips and other service information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
TSB 22-2428 is missing some labor operations. For any missing labor operations, claim available new model labor operations or m-time. Refer to this article on the repair order. When replacing the CDF cylinder, the current TSB does not require a complete transmission overhaul or cooler and converter flushing. Ford is currently reviewing the TSB. Monitor OASIS for updates.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · POWER TRAIN · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Explorer vehicles equipped with 2.3L engine and 10R60 automatic transmission may exhibit a delayed reverse engagement. This may be due to the software in the powertrain control module (PCM). To correct the condition, follow the Service Procedure to reprogram the PCM.
Source components: POWER TRAIN · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE:SOFTWARE · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2023 F-150, 2018-2023 Expedition/Navigator/Mustang, 2019-2023 Ranger, 2020-2023 Explorer/Aviator/Transit and 2021-2023 Bronco vehicles equipped with a 10R60 transmission and built on or before 23-Dec-2022 or with a 18R80/10R80MHT transmission and built on or before 15-Aug-2022 may exhibit a harsh/delayed engagement and/or harsh/delayed shift. It is possible the vehicle may also have an illuminated malfunction indicator lamp (MIL) or diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to the software in the PCM or TCM, the transmission solenoid ID strategy, sticking valves in the main control valve body and/or axial movement of the CDF clutch cylinder (7H351) sleeve.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 Ford and Lincoln vehicles equipped with a 2.7L or 3.0L engine may exhibit an upper engine thump/knock noise coming from the left cylinder head. This condition is most noticeable at idle and may lessen at higher engine speed or while driving. This condition does not affect vehicle durability and will not get worse over time. Use a stethoscope or chassis ears and listen just behind the left cylinder head intake VCT solenoid on the cam cover to determine if the thump/knock noise is coming from the cylinder head/camshaft. The left cylinder head and the camshaft roller followers are available as service parts.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2020-2023 Escape/Explorer, 2021-2023 F-150 and 2022-2023 Maverick vehicles equipped with a full hybrid electric vehicle (FHEV) powertrain may exhibit a cable connection error screen from the Midtronics xRC-3363 High Voltage Battery Rescue Charger. The xRC-3363 will prompt the Technician to verify the low voltage connections, when no actual fault is present. The technician will need to delete the WiFi connection from the xRC-3365 so it will not automatically reconnect and adjust the date. Next go to Settings>Shop Information>Date/Time Settings and change the date prior to May 1, 2023 and stay off the internet so it will not auto correct itself. Press and hold the power button until the tool turns off. Then turn the xRC-3365 back on and attempt the rescue charge.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022 Aviator/Bronco/Expedition/Explorer/F-150/Mustang/Navigator/Ranger/Transit vehicles built on or before 31-Jul-2022 equipped with a 10R60/10R80/10R80 MHT automatic transmission may exhibit a fluid leak from the selector shaft seal. This may be caused by a crack in the manual shaft. To correct this condition, follow the Service Procedure to replace the manual shaft, the manual shaft-to-sensor roll pin and the selector shaft seal.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2023 Explorer vehicles may exhibit a condition of intermittent headlamp operation while the vehicle is OFF and have diagnostic trouble code (DTC) B1533 stored in the body control module (BCM). This may be due to the internal logic within the headlamp switch. Switch and/or module replacement will not resolve this condition. Headlamp operation is not affected while the vehicle is ON. A new headlamp switch is currently under development to correct this condition. The customer can continue to drive the vehicle until parts become available. Monitor OASIS for updated repair information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022-2023 Explorer vehicles equipped with a 2.3L engine may exhibit an intermittent malfunction indicator light (MIL) with diagnostic trouble code (DTC) P1026 and/or P1299 present in the powertrain control module (PCM) and an engine over-temperature message displayed on the instrument panel cluster (IPC) after a cold engine start. The vehicle will also exhibit reduced performance when it enters fail safe cooling open loop mode. If the engine is not overheating, clear the DTCs to reset the fail safe cooling open loop mode. Start and idle the engine while viewing coolant flow at the top inner (engine side) degas bottle hose port through the semitransparent top. If coolant flow is blocked, replace the L1MZ-8A365-AAD engine-to-degas bottle hose. If flow is steady, return to Workshop Manual (WSM), Section 303-03A diagnostics.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2022-2023 Explorer/Aviator vehicles built on or after 28-May-2022, 2022-2023 Expedition/Navigator vehicles built on or after 08-Jun-2022 and 2022 Escape/Corsair vehicles built on or after 01-Jun-2022 are no longer equipped with a hands free liftgate system. The vehicle is not misbuilt. The addition of any parts is not a warrantable repair. Do not submit a claim for this condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2022 Model Year Explorer Vehicles Rear Climate Control Module Retrofit REASON FOR THIS SUPPLEMENT Program Terms: Removal of mileage limit. Affected Vehicles: Added US population of affected vehicles. FSA VIN Lists Activation: VIN list activation added. Owner Notification Mailing Schedule: Update owner letter mailing date. Pick-up and Delivery: Added pick-up and delivery. Claims Preparation and Submission: Added pick-up and delivery and mobile repair. Labor Allowances: Update to include pick-up and delivery labor operation and mobile service description
NHTSA source summary · Original PDF not reviewed by Recallfolio
2022-2023 Police Interceptor Utility (gas engine) and all 2022-2023 Explorer vehicles built on or after 14-Jul-2022, 2022-2023 Police Interceptor Utility (hybrid) vehicles built on or after 17-Aug-2022, 2023 Aviator (gas engine) vehicles built on or after 18-Jul-2022, and 2023 Aviator (hybrid) vehicles built on or after 27-Jul-2022 are not equipped with a rear parking aid camera wash feature. The feature was deleted; however, the rear parking aid camera washer jet may still be present without a hose attached to it. This is normal and no repair attempts should be made.
NHTSA source summary · Original PDF not reviewed by Recallfolio
For 2000-2024 Ford and Lincoln vehicles, swapping a module from a vehicle for diagnosis purposes is likely to cause errors and is not recommended. It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2023 Explorer/Aviator/Transit, 2021-2023 F-150/Bronco, 2022-2023 Expedition/Navigator/Mustang and 2023 F-250/F-350 Super Duty vehicles may exhibit harsh/delayed engagement and/or harsh/delayed shift concerns. These may be addressed with the powertrain control module (PCM)/transmission control module (TCM) Transmission Accelerated Main Control Break In Routine and/or a main control overhaul. Refer to Workshop Manual (WSM), Section 307-01, DTC Chart if DTCs are present and/or Diagnosis By Symptom to identify the clutch(s) to be cycled. Cycling the shift solenoids and clutch control valves to remove contamination must be performed along with an adaptive drive cycle before attempting repair. For claiming, use causal part 7A100 and applicable labor operations in Section 7 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 Explorer Timberline vehicles may exhibit differential fluid venting from the differential fluid vent. The customer may notice differential fluid pooling below the vehicle or saturating the wheel well liner. This may be due to the differential vent tube not having enough positive incline. To correct the condition, follow the Service Procedure to replace the differential vent tube.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2020-2023 Explorer/Aviator with start/stop push button ignition switch may exhibit an illuminated malfunction indicator lamp (MIL) and powertrain malfunction (wrench) indicator with diagnostic trouble code (DTC) B108A:01 (general electrical failure), B108A:24 (signal stuck high), and/or B108A:9E (stuck on). The ignition mode light emitting diode (LED) indicator may also flash quickly. This condition may be caused by loose wiring terminal crimps on connector C2195 at the push button ignition switch. Examine Pin 1 (CPK34/Gn) first, since it is the only pin with the smallest (26 gauge) wire. To correct this condition, repair terminal crimps per Wiring Diagram (WD) Cell 5. If no wiring terminal faults are found, refer to Workshop Manual (WSM) Section 211-05 for normal diagnostics. The push button ignition switch pinpoint tests in the WSM have been updated.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2023 Ford and Lincoln SYNC3 equipped vehicles may experience an inaccurate notification in the FordPassî/LincolnWayî app indicating Vehicle Has Entered Deep Sleep Mode. Vehicle Has Entered Deep Sleep Mode message is expected if the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SoC) drops below 50%. If the vehicle is going into deep sleep outside these conditions, this may be due to the telematics control unit (TCU) software. To correct this condition, follow the Service Procedure to update the TCU to the latest software. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2023 Explorer/Aviator 4x4/AWD vehicles with hybrid powertrain may experience a harshness and/or vibration felt through the seat, steering wheel and/or center console after initial driveaway between 25-50 MPH (40-80 Km/h) that lessens after driving 5-10 minutes. This may be due to driveshaft center bearing bounce mode during cold ambient temperatures. To resolve the concern, install a softer durometer L1MZ-4A499-F driveshaft center bearing per Workshop Manual Section 205-01. For claiming, use causal part 4A499 and applicable labor operations in Section 4 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022-2023 Explorer vehicles may exhibit a buzz/vibration/rattle from the center left of the IP during tip-in when the vehicle is up to operating temperature. This may be due to heater tube movement against the tube bracket.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2023 Ford and Lincoln vehicles equipped with a 10R60/10R80/10R80 MHT/10R100 transmission may exhibit a whine noise at idle and/or while driving. This may be identified as coming from the bellhousing and the front of the transmission fluid pan. The whine noise may become louder when the transmission is at operating temperature and may increase with engine revolutions per minute (RPM) in the park (P) position. A small amount of whine noise is considered to be characteristic of the 10R60/10R80/10R80 MHT/10R100 transmissions due to the offset gear drivetrain in the front support and has no effect on durability.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022 Explorer/Aviator/Bronco vehicles built on or before 9-Aug-2022 and equipped with a 10R60 automatic transmission may exhibit a harsh 7-6 gear downshift. This may be caused by the A clutch piston return spring snap ring becoming dislodged. To correct the condition, follow the Service Procedure to replace the front support assembly and A clutch components.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles equipped with a 2.7L, 3.0L,3.5L or 5.0L engine may require replacement of the long block engine assembly. New service kits have been released which include all the one-time-use components required in the service procedure for removal and replacement of the long block engine assembly. Refer to the Ford Electronic Parts Catalog (ECAT) for long block service kit part number by application.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2023 Explorer/Aviator vehicles may exhibit the A/C blowing warm air with DTCs P0645, P2CFC, and/or P2CFD present in the heating ventilation and air conditioning (HVAC) module. This may be due to spread terminal/terminal pushout in wire harness 14290 and on the corresponding pins to the body control module C (BCMC). Before replacement of the BCMC, disconnect all connectors from the BCMC and check the BCMC pins and wire terminals for damage. Refer to Workshop Manual (WSM), Section 419-10. If spread terminals or terminal pushout is present, repair as necessary. Refer to Wiring Diagram, Cell 005 for repair procedures. Reconnect all connections to the BCMC as indicated by the procedure in the WSM. Test the function of the A/C to verify that it is blowing cold air.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022-2023 Explorer vehicles equipped with a 2.3L engine may exhibit an intermittent check engine light on with diagnostic trouble code (DTC) P1026 and/or P1299 present in the powertrain control module (PCM) and an engine over-temperature message displayed on the instrument panel cluster (IPC) after a cold start in cold (at or below freezing) ambient temperatures. The vehicle may also enter fail safe cooling open loop mode when this concern occurs. If the engine does not show any obvious signs of overheating and Workshop Manual, Section 303-03A diagnostics are inconclusive, clear the DTCs to reset the fail safe cooling open loop mode. Inform the customer that Ford is currently investigating this concern and that they can continue to drive the vehicle. Monitor OASIS for further updates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2020-2022 Aviator/Explorer/Police Interceptor, 2021-2022 F-150 vehicles equipped with a 10R80 MHT transmission and built on or before 15-Nov-2022 may exhibit an 8th gear start after coming to a stop and/or a no movement in Reverse condition. This may be due to the driver applying the accelerator pedal and brake pedal simultaneously during regenerative braking. To improve the condition, follow the Service Procedure to reprogram the powertrain control module (PCM) and refer the customer to the Automatic Transmission Section of the Owners Manual warning regarding applying both pedals simultaneously.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2023 F-150, Expedition, Navigator, Transit, Aviator and Explorer vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0627, P025A, P025B, P00C6, P008A and/or U0109 stored in the powertrain control module (PCM). This may be due to an intermittent or partial disconnect of the harness to the fuel pump control module (FPCM) connector, connector pin push-outs, damaged pins/terminals, or loose/corroded grounds. Inspect FPCM connector, applicable grounds (F-150 - G401, Expedition/Navigator - G403, Transit - G401, 2018-2019 Explorer G302, 2020-2022 Explorer/Aviator - G407) and confirm FPCM connector (F-150 - C4336, Expedition/Navigator - C433, Transit - C433, 2018-2019 Explorer - C3239, 2020-2022 Explorer/Aviator - C4033) is fully seated prior to performing PC/ED diagnostics or replacing any components.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2023 Explorer/Aviator/Police Interceptor Utility vehicles equipped with a hybrid powertrain may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P2D40. This may be due to the high voltage battery thermal system not cooling as it should. Follow the updated WSM Section 414-03 including listed possible sources, visual inspection and prechecks, and diagnostic procedures.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles equipped with power folding mirrors may exhibit power folding mirrors that are inoperative or exhibit a clicking sound. This may be due to the mirrors being manually folded in, during transportation, going through a car wash, bumped in a parking lot, or found during pre-delivery inspection (PDI). Prior to the replacement of any components, attempt to synchronize the mirrors by following the Power Mirrors Synchronization procedure. Refer to Workshop Manual (WSM) Section 501-09 Rear View Mirrors - General Procedures - Power Mirrors Synchronization.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 22-2176 to increase the labor operation allowance and update the part list. Some 2020-2022 Escape/Corsair vehicles built on or before 3-Jan-2022, 2020-2022 Explorer vehicles built on or before 14-Feb-2022, 2020-2022 Aviator vehicles built on or before 07-Feb-2022 and 2021-2022 Bronco Sport vehicles built on or before 3-Dec-2021 may exhibit a slow fuel fill and/or spit back condition during refueling. This may be due to the design of the fuel tank filler pipe. To correct the condition, follow the Service Procedure to replace the fuel tank filler pipe.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2021 Expedition/Navigator, 2020-2022 F Super Duty/Explorer, 2021-2022 Bronco/Corsair/Escape/Bronco Sport, 2022 Maverick vehicles may exhibit the wireless charger inoperative or poor performance when using some Apple iPhone models that use MagSafe wireless charging including iPhone 12 and 13. This may be due to limited compatibility with the wireless accessory charging module (WACM). To correct the condition, follow the Service Procedure to update the WACM. Note: The WACM software is designed to improve the compatibility between some Apple MagSafe charging iPhones, including iPhone 12 and 13 models, and the Ford Qi wireless charging module.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Explorer vehicles equipped with a 2.3L engine may exhibit an illuminated malfunction indicator lamp (MIL) with multiple diagnostic trouble codes (DTCs). These DTCs may include P04F0, P008A, P0451, P0455, P0456, P0496 and/or P018C. This may be due to the wiring harness connection at connector C1198 on driver's side lower frame area underneath the brake lines that route near the electric brake booster (EBB). Prior to replacement of any components, inspect the connector and wiring harness for any damage or pin fit concerns. If any damage or pin fit concerns are found, repair the connector or harness as necessary. If no damage or pin fit concerns are found, refer to normal diagnostics. Refer to Wiring Diagram (WD) Cell 22-12 to view the 3 voltage reference (VREF) wires at C1198 on the 2.3L engine.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2023 Ford and Lincoln vehicles equipped with a telematic control unit (TCU) may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization, and/or modem electronic serial number (ESN) could not be displayed in the center display screen. To correct this condition prior to programming, remove the TCU fuse for 5-minutes then reinstall. Delete all previous session files for the vehicle. Start a new Ford Diagnosis and Repair System (FDRS) session. Perform a TCU provisioning and Program the TCU to the latest FDRS version level. If the concern is still present, follow normal diagnostics in Workshop Manual (WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2022 Model Year Explorer Vehicles Rear Climate Control Module Retrofit In all of the affected vehicles, a global supply shortage of semiconductor chips caused unavailability of the rear heating, ventilation and air conditioning control (RHVAC) module for certain vehicles.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Explorer/Aviator vehicles equipped with a 3.0L EcoBoost engine may exhibit a ticking/tapping or rattle type noise from the top front cover area of the engine on initial start-up after a cold soak of 6 hours or more that may last for 2-5 seconds. This may be due to a worn variable cam timing (VCT) unit. To correct the condition, follow the Service Procedure to replace the VCT units.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Explorer vehicles equipped with a 2.3L engine may exhibit an illuminated malfunction indicator lamp (MIL) with multiple diagnostic trouble codes (DTCs). These DTCs may include P04F0, P008A, P0451, P0455, P0456, P0496 and/or P018C. This may be due to the wiring harness connection at connector C1198. Prior to replacement of any components, inspect the connector and wiring harness for any damage or pin fit concerns. If any damage or pin fit concerns are found, repair the connector or harness as necessary. If no damage or pin fit concerns are found, refer to normal diagnostics.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:WIRING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Ford and Lincoln vehicles equipped with a telematic control unit (TCU) may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization, and/or modem electronic serial number (ESN) could not be displayed in the center display screen. To correct this condition prior to programming, remove the TCU fuse for 5-minutes then reinstall. Delete all previous session files for the vehicle. Start a new Ford Diagnosis and Repair System (FDRS) session. Perform a TCU provisioning and Program the TCU to the latest FDRS version level. If the concern is still present, follow normal diagnostics in Workshop Manual (WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: COMMUNICATION:MANUFACTURER TELEMATICS · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Explorer - Timberline - vehicles may exhibit a rear differential that is venting rear axle fluid. This may result in a noise, odor, or leak noticed by the customer. Inspect the rear of the vehicle for signs of rear differential fluid venting into the rear wheel well, or leaking from the rear differential. If signs of fluid leaks are found from any seals, repair as necessary per Workshop Manual Section 205-02. If no seal leaks are found but fluid is venting, drain the rear differential. Add 85-100 ml of Motorcraft® XL-3 Additive Friction Modifier. Refill with fresh rear differential fluid to bottom of fill plug. Remove the vent tube and use compressed air to verify that the fluid vent tube is clear, then reinstall tube. Engineering investigating, monitor OASIS for updates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2020-2022 Model Year Explorer Vehicles Rear Axle Bolt Replacement REF : NEW VEHICLE DEMONSTRATION / DELIVERY HOLD Safety Recall 22S27 Supplement #3
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Explorer/Aviator/Police Interceptor Utility vehicles equipped with a hybrid powertrain may exhibit an illuminated MIL with diagnostic trouble code (DTC) P2D40. This may be due to the chiller not interpreting the correct cooling value of the high voltage battery chiller. To correct the condition, follow the Service Procedure to diagnose the cause of the incorrect value.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022 Explorer/Police Interceptor Utility and 2022-2023 Aviator vehicles built on or before 19-Aug-2022 and equipped with 3.0L Ecoboost engines may exhibit an engine coolant leak at the water pump output spigot to the transmission oil cooler inlet hose connection. This may be due to the connection at the water pump outlet to coolant hose. To correct this condition, replace the coolant hose assembly with service part number L1MZ-7G071-A.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Explorer/Aviator vehicles may exhibit automatic transmission fluid (ATF) contamination in the engine cooling system due to the transmission cooler. If the cooling system becomes contaminated with ATF, the system must be flushed clear of the contamination after the source of the contamination has been repaired. It is generally not necessary to replace the following components due to ATF contamination in the cooling system: radiator, heater core, de-gas bottle, water pump, auxiliary water pump, coolant control valves, temperature sensors, thermostat, turbocharger, heat exchangers, tubes, gaskets/O-rings/seals (unless removed), or rubber coolant hoses (unless swollen).
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Explorer/Police Interceptor Utility vehicles equipped with a 3.3L Duratec engine may exhibit delayed acceleration response under heavy to wide open throttle input after an engine start. This concern occurs only during the first 30 seconds from key on with no diagnostic trouble codes (DTCs) stored in the powertrain control module (PCM). The customer may perceive this as a delayed throttle response or lack of power. This may be due to the software in the PCM. Engineering is releasing updated software to resolve this concern, which is expected to be released in August 2022. Monitor OASIS for updates and schedule service appointments for customers once the repair becomes available.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2022 Ford/Lincoln customers may experience a notification in the FordPassÃÂÃÂÃÂî/LincolnWayÃÂÃÂÃÂî app indicating Vehicle Has Entered Deep Sleep Mode. This occurs when the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SOC) drops below 50%. A warning may also set if the telematic control unit (TCU) has received an over the air update. The TCU powers down all communication when in this mode and app features are disabled. Manually start the vehicle to wake if from mode. More information is located in the app under: Account > Help > search 'Deep Sleep' in the entry box. If the condition remains, check the BCM 12v SOC. If the SOC does not change after charging the battery or after BMS reset is performed, continue with normal battery and/or BMS sensor diagnostics.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019-2022 Edge/Nautilus, 2018-2022 Expedition/Navigator, 2020-2022 Explorer/Aviator vehicles equipped with a family entertainment system may experience the audio is not synchronized with the video display when using the vehicle speakers. To correct this condition, contact the VOXX Customer Service Department at 1-866-869-7888. For claiming, refer to the Warranty and Policy manual for Ford Licensed Accessories.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Explorer/Aviator vehicles may exhibit a lack of audio and/or a water leak in the rear liftgate area and/or water in the spare tire area. The customer may indicate that this concern is more noticeable after a car wash or rainfall. To correct the condition, follow the Service Procedure to identify the leak path.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Explorer/Aviator/Police Interceptor Utility vehicles may exhibit a rear differential that is venting rear axle fluid. This may result in a noise, smell, or leak noticed by the customer. Inspect the rear of the vehicle for signs of rear differential fluid venting in the right rear wheel well (oil staining in the wheel well liner and/or oil residue on the wheel end assembly below) or leaking from the rear differential. If signs of fluid leaks are found from any seals, repair as necessary. Refer to Workshop Manual (WSM), Section 205-02. If no seal leaks are found but fluid is venting, drain the rear differential and re-fill with fresh rear differential fluid. Remove the vent tube and use compressed air to verify that the fluid vent tube is clear. Reinstall the vent tube. Engineering is investigating, monitor OASIS for updates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Mustang/Ranger/Transit Connect, 2020-2021 EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator, 2021 Bronco Sport and 2020-2022 Explorer/Aviator vehicles with SYNC 3 may experience various SYNC performance related concerns. This may be due to the SYNC Software. To correct the condition, follow the Service Procedure to update the accessory protocol interface module (APIM) software.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2020-2022 Explorer/Aviator and 2021-2022 F-150 hybrid vehicles equipped with a 10R80 MHT require the Transmission Strategy Download application in the Ford Diagnosis and Repair System (FDRS) to be run after certain transmission or module repairs. The Transmission Strategy Download routine is failing in FDRS levels 32.5.3 and 32.5.4. The FDRS development team is working to resolve this in a future release of FDRS. In the meantime, uninstall FDRS from the computer using the select all function to remove all data and recordings. Reinstall the older FDRS version 31.6.5 using this url - http://www.fordservicecontent.com/Ford_Content/IDS/FDRS/FDRS_31.6.5.exe Once 31.6.5 is installed, download and run the Transmission Strategy Download application.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Explorer/Aviator vehicles may exhibit a concern of inoperative, rattling, crackling and/or distorted sound from one or more speakers. In order to correct the condition, make sure to completely follow the diagnostics in Workshop Manual (WSM), Section 415-00, Pinpoint Test D for vehicles without SYNC 3, and WSM, Section 415-00B, Pinpoint Test E for vehicles equipped with SYNC 3. If the diagnostics point towards speaker replacement, remove and re-center the speaker, making sure to tighten to the specified torque and retest. Refer to WSM, Section 415-00.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Explorer/Aviator/Police Interceptor Utility vehicles may exhibit erratic transfer case operation and/or noise. This may be due to water intrusion between the transmission and the transfer case. The transfer case installation procedure has been updated in Workshop Manual (WSM), Section 307-07B to prevent this concern from reoccurring. Follow the updated WSM procedure to make sure the top of the transfer case is sealed upon installation.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2022 Ford and Lincoln vehicle owners may experience a condition of missing authorization, command and control, battery charging details or phone-as-a-key setup buttons/selections in their FordPass or LincolnWay App. This condition is due to an error within the FordPass or LincolnWay App and not due to a concern on the vehicle. Verify that the customers FordPass or LincolnWay App is at the latest version. Replacement or reprogramming of the telematics control unit (TCU)/gateway module (GWM)/remote function actuator (RFA) will not resolve this condition. If the condition persists, utilize the FordPass Guides or Lincoln Way Concierge teams.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Escape/Corsair vehicles built on or before 3-Jan-2022, 2020-2022 Explorer vehicles built on or before 14-Feb-2022, 2020-2022 Aviator vehicles built on or before 07-Feb-2022 and 2021-2022 Bronco Sport vehicles built on or before 3-Dec-2021 may exhibit a slow fuel fill and/or spit back condition during refueling. This may be due to the design of the fuel tank filler pipe. To correct the condition, follow the Service Procedure to replace the fuel tank filler pipe.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Explorer/Aviator vehicles may exhibit a second row folding seat that is inoperative or requires excessive effort to fold. This may be due to tension built up within the seat and seat track that leads to more force required to manually fold the seat. To correct the condition, the second row seat frame will need to be unbolted from the floor and tightened in the correct sequence. Additionally, the sliding tracks of the seat should be inspected for proper alignment when tightening the bolts. It is important to note that the bolts should be started by hand before tightening to the correct torque. This sequence is outlined in Workshop Manual (WSM), Section 501-10. The WSM has been updated to reflect the updated bolt installation procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2020-2022 Model Year Explorer (Non-Police) Vehicles - Rear Axle Repair After Bolt Fracture. In some of the affected vehicles, the rear axle mounting bolt may fracture during vehicle acceleration. A fractured rear axle bolt will allow the rear axle housing to move out of position, resulting in severe noise and vibration. If the rear axle bolt breaks, the driveshaft/half shafts may become disconnected, resulting in loss of transmission torque to the rear wheels which is necessary to hold the vehicle in park. If the parking brake is not applied, the loss of the primary park torque will allow the vehicle to roll in park increasing the risk of crash and injury.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Mustang/Ranger/Transit Connect, 2020-2021 EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator, 2021 Bronco Sport and 2020-2022 Explorer/Aviator vehicles with SYNC 3 may experience various SYNC performance related concerns. This may be due to the SYNC Software. To correct the condition, follow the Service Procedure to update the accessory protocol interface module (APIM) software.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2022 F-150, Expedition, Navigator, Transit, Aviator and Explorer vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0627, P025A, P025B, P00C6, P008A and/or U0109 stored in the powertrain control module (PCM). This may be due to an intermittent or partial disconnect of the harness to the fuel pump control module (FPCM) connector, connector pin push-outs, damaged pins/terminals, or loose/corroded grounds. Inspect FPCM connector, applicable grounds (F-150 - G401, Expedition/Navigator - G403, Transit - G401, 2018-2019 Explorer G302, 2020-2022 Explorer/Aviator - G407) and confirm FPCM connector (F-150 - C4336, Expedition/Navigator - C433, Transit - C433, 2018-2019 Explorer - C3239, 2020-2022 Explorer/Aviator - C4033) is fully seated prior to performing PC/ED diagnostics or replacing any components.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Explorer/Aviator vehicles may exhibit the A/C blowing warm air with DTCs P0645, P2CFC, and/or P2CFD present in the heating ventilation and air conditioning (HVAC) module. This may be due to spread terminal/terminal pushout in wire harness 14290 and on the corresponding pins to the body control module C (BCMC). Before replacement of the BCMC, disconnect all connectors from the BCMC and check the BCMC pins and wire terminals for damage. Refer to Workshop Manual (WSM), Section 419-10. If spread terminals or terminal pushout is present, repair as necessary. Refer to Wiring Diagram, Cell 005 for repair procedures. Reconnect all connections to the BCMC as indicated by the procedure in the WSM. Test the function of the A/C to verify that it is blowing cold air.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Explorer/Aviator vehicles may exhibit an inoperative power liftgate when using intelligent access (IA) features such as the hands free liftgate or when using the outside control button on the liftgate handle when the doors are locked. This may be due to a poor wiring connection at connector C4332 for the rear keyless entry antenna. If these symptoms are present, inspect C4332 (below the liftgate striker) for a poor connection, loose terminals, or improper pin-fit.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2023 Ford or Lincoln vehicles with modems activated through FordPass or LincolnWay may experience 12 volt battery drain symptoms when the customer uses non-Ford/Lincoln phone applications as an alternate channel to access vehicle commands such as door lock/unlock, remote start, vehicle location, etc. The battery drain may be caused by excessive calls for data through the vehicle network keeping it in an activated state. Recommend that the customer uninstall the app to ensure this is not contributing to battery symptoms experienced. Advise the customer that unaffiliated third-party app developers do not work directly with Ford to adhere to security, vehicle communication, and privacy requirements.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Explorer/Aviator and 2021-2022 Bronco vehicles may exhibit an illuminated airbag warning indicator with diagnostic trouble code (DTC) B1404:13 and/or B1407:13. This may be due to contamination and relative movement in the connection between the wiring harness and the side airbag. To correct the condition, follow the Service Procedure to replace the affected connector with a service pigtail and the affected side airbag.
Source components: AIR BAGS:SRS MALFUNCTION WARNING LAMP/LIGHT · ELECTRICAL SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022 Explorer/Aviator vehicles may exhibit an intermittent passenger seat massage function with no diagnostic trouble codes (DTCs). This may be due to the software and configuration of the seat control module G (SCMG) and seat control module H (SCMH). To correct the condition, download and run the SCMG and SCMH software update application using the latest software level of the Ford Diagnosis and Repair System (FDRS). For claiming, use causal part 14F548 and applicable labor times found in Section 10 of the Service Labor Time Standards (SLTS) Manual.