The manufacturer’s record · Page 2 of 2
Original record summaries, dates and identifiers for this model-year. Records 101–134 of 134, ordered newest first. Dated records on this page: Sep 19, 2018–May 22, 2019.
Back to 2019 Ford EXPLORER problems & recallsThis archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
NHTSA communication ID: 10160951
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2019 Model Year Explorer - Anti-lock Brake System Module Software Update
Source components: SERVICE BRAKES, HYDRAULIC.
Source record 10160951 at NHTSANHTSA communication ID: 10160953
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2019 Model Year Explorer - Anti-lock Brake System Module Software Update
Source components: SERVICE BRAKES, HYDRAULIC.
Source record 10160953 at NHTSANHTSA communication ID: 10160931
NHTSA source summary · Original PDF not reviewed by Recallfolio
On vehicles equipped with an automatic transmission it is imperative that the converter pilot hub be greased with Motorcraft Multi-Purpose Grease Spray XL-5-A even if grease was not applied from the factory. Also verify that the engine/transmission alignment dowel pins are present as well as the engine crankshaft dowel pin, if equipped, when installing the transmission. Failure to adequately lubricate the converter hub greatly increases the likelihood of the flexplate cracking in the future. Missing dowels may cause a misalignment issue also resulting in a premature failure. Refer to Workshop Manual (WSM), Section 307-01.
Source components: POWER TRAIN.
Source record 10160931 at NHTSANHTSA communication ID: 10160880
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2019 vehicles equipped with a EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.
Source components: EQUIPMENT:APPLIANCE:AIR CONDITIONER.
Source record 10160880 at NHTSANHTSA communication ID: 10160876
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2019 Explorer vehicles may exhibit a loose cushion cover corner and/or exposed foam on the 2nd row left 60 percent seat. The left 2nd row 60 percent seat cushion cover is a different design from the right 2nd row 40 percent cushion cover and the two are not comparable. The right seat trim wraps under the seat and is closed off while the left side is not closed off and may appear loose. This is normal appearance and no repairs should be performed. If the seat foam is exposed, the foam can be tucked upward and the cushion cover refitted to conceal the foam. The seat cushion cover and/or foam should not be replaced for either condition.
Source components: SEATS.
Source record 10160876 at NHTSANHTSA communication ID: 10159494
NHTSA source summary · Original PDF not reviewed by Recallfolio
SSM 47948 - 2010-2019 Various Vehicles - Turbocharged Engines - Oil Supply Filter Replacement When Replacing The Turbocharger Or The Turbocharger Oil Supply Tube For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. When specified in the WSM, the turbocharger oil supply filter must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.
Source components: ENGINE.
Source record 10159494 at NHTSANHTSA communication ID: 10159489
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2019 vehicles equipped with a EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:APPLIANCE:AIR CONDITIONER.
Source record 10159489 at NHTSANHTSA communication ID: 10159507
NHTSA source summary · Original PDF not reviewed by Recallfolio
SSM 47926 - 2018-2019 F-150/Expedition/Navigator/Transit/Explorer - Illuminated MalfunctionIndicator Lamp (MIL) With Diagnostic Trouble Code (DTC) P025A Some 2018-2019 F-150, Expedition, Navigator, Transit and Explorer vehicles may exhibit an illuminated MIL with DTC P025A stored in the powertrain control module (PCM). This may be due to an intermittent or partial disconnect of the harnessto the fuel pump driver module (FPDM) connector. Confirm FPDM connector (F-150 C4336, Expedition/Navigator C433, Transit C433, Explorer C3239) is fully seated prior to performing PC/ED diagnostics or replacing any components. APPLICABLE VEHICLES
Source components: ELECTRICAL SYSTEM · FUEL SYSTEM, GASOLINE.
Source record 10159507 at NHTSANHTSA communication ID: 10159505
NHTSA source summary · Original PDF not reviewed by Recallfolio
SSM 47914 - 2016-2019 Explorer roof rack cap trim clips now available. 2016-2019 Explorer roof rack cap clips are now available as a separate part. It is no longer necessary to order a complete roof rack rail to obtain the cap retainer clips. To correct loose roof rack caps or broken or missing clips, order part number FB5Z-7851050-A. Ensure roof rails are properly torqued to 55 in/lbs (6.2 Nm) and that power tools are not used for installation as over-torqueing may cause warpage and poor fitment.
Source components: STRUCTURE · STRUCTURE:BODY:ROOF AND PILLARS.
Source record 10159505 at NHTSANHTSA communication ID: 10156598
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various 2019 vehicles equipped with SYNC 3 and the latest software version 3.2 may exhibit an error message when attempting to update the software to version 3.3. Professional Technician Society (PTS) website may show that software version 3.3 is available for 2019 SYNC 3 vehicles. Do not carry out this update as it may lead to a hardware error message. Engineering is investigating, monitor OASIS for updates.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:SOFTWARE.
Source record 10156598 at NHTSANHTSA communication ID: 10156481
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019 Explorer/Police Interceptor Utility vehicles built on 10-Sep-2018 and through 07-Feb-2019 may exhibit a lack of hill start assist when the vehicle is stopped on an incline greater than 1.5 degrees. If no diagnostic trouble codes (DTCs) are stored in the anti-lock brake system (ABS) module, reprogram the ABS module using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 2C219 and applicable labor operations in Section 02 of the Service Labor Time Standards (SLTS) Manual.
Source components: SERVICE BRAKES, HYDRAULIC.
Source record 10156481 at NHTSANHTSA communication ID: 10156887
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2017 vehicles may experience a no crank concern due to a security access key table error. When attempting to program keys or perform a parameter reset, the procedure may fail and the Integrated Diagnostic System (IDS) scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the Body Control Module (BCM) is internally faulted and requires replacement. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
Source components: ELECTRICAL SYSTEM.
Source record 10156887 at NHTSANHTSA communication ID: 10155575
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2017 vehicles may experience a no crank concern due to a security access key table error. When attempting to program keys or perform a parameter reset, the procedure may fail and the Integrated Diagnostic System (IDS) scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the Body Control Module (BCM) is internally faulted and requires replacement. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
Source components: ELECTRICAL SYSTEM.
Source record 10155575 at NHTSANHTSA communication ID: 10156885
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2019 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 or no modem electronic serial number (ESN) displayed. To correct this condition prior to programing remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229.
Source components: ELECTRICAL SYSTEM.
Source record 10156885 at NHTSANHTSA communication ID: 10155573
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2019 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 or no modem electronic serial number (ESN) displayed. To correct this condition prior to programing remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229.
Source components: ELECTRICAL SYSTEM.
Source record 10155573 at NHTSANHTSA communication ID: 10156883
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2019 Explorer, 2016-2018 MKX, 2019 Edge/Nautilus, 2017-2019 Fusion/MKZ, and 2018-2019 F-150/Mustang/Expedition/Navigator vehicles equipped with climate controlled seats may exhibit a buzzing noise from the front seats, front seats too warm, and/or inoperative climate controlled front seats. DTCs B14BA:13, B1154:4B, and/or B14B9:13 may also be present. This may be due to loose terminal pin fit on the driver seat module (DSM) connector C341D (16 pin). If a loose terminal pin fit condition is found during normal diagnostics per Workshop Manual (WSM), Section 501-10, a new service pigtail connector (part number 3U2Z-14S411-BRAB) is available. Refer to Wiring Diagram, Cell 119 to make sure C341D is a 16 pin connector and not a 20 pin connector. Refer to Wiring Diagram, Cell 5 for the recommended splicing procedures.
Source components: ELECTRICAL SYSTEM · SEATS · SEATS:FRONT ASSEMBLY:SEAT HEATER/COOLER.
Source record 10156883 at NHTSANHTSA communication ID: 10155571
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2019 Explorer, 2016-2018 MKX, 2019 Edge/Nautilus, 2017-2019 Fusion/MKZ, and 2018-2019 F-150/Mustang/Expedition/Navigator vehicles equipped with climate controlled seats may exhibit a buzzing noise from the front seats, front seats too warm, and/or inoperative climate controlled front seats. DTCs B14BA:13, B1154:4B, and/or B14B9:13 may also be present. This may be due to loose terminal pin fit on the driver seat module (DSM) connector C341D (16 pin). If a loose terminal pin fit condition is found during normal diagnostics per Workshop Manual (WSM), Section 501-10, a new service pigtail connector (part number 3U2Z-14S411-BRAB) is available. Refer to Wiring Diagram, Cell 119 to make sure C341D is a 16 pin connector and not a 20 pin connector. Refer to Wiring Diagram, Cell 5 for the recommended splicing procedures.
Source components: SEATS.
Source record 10155571 at NHTSANHTSA communication ID: 10156856
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2011-2019 Explorer and 2013-2019 Police Interceptor Utility vehicles may exhibit a detached center console rear cup holder and/or the cover panel detached from the rear cup holder. Follow the Service Procedure steps to correct the condition.
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10156856 at NHTSANHTSA communication ID: 10155444
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2011-2019 Explorer and 2013-2019 Police Interceptor Utility vehicles may exhibit a detached center console rear cup holder and/or the cover panel detached from the rear cup holder. Follow the Service Procedure steps to correct the condition.
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10155444 at NHTSANHTSA communication ID: 10156877
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2009-2017 Expedition/Navigator, 2009-2014 F-150/Mustang, 2008-2009 Sable, 2008-2019 Taurus/Flex/MKT, 2013-2019 Police Interceptor Sedan/Utility, and 2011-2019 Explorer vehicles may exhibit inoperative or intermittent HVAC blower motor function at various fan speed settings. This may be due to a poor electrical connection at the blower motor speed control. If the blower motor speed control is determined to be the causal part, replacement of the electrical connector pigtail harness (14S411) to the blower motor speed control is also recommended to avoid repeat repairs. Refer to Wiring Diagram, Cell 5 for recommended splicing procedures. Refer to Wiring Diagram, Cells 54/55 to obtain the service pigtail connector part number.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · EQUIPMENT:APPLIANCE:AIR CONDITIONER.
Source record 10156877 at NHTSANHTSA communication ID: 10155565
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2009-2017 Expedition/Navigator, 2009-2014 F-150/Mustang, 2008-2009 Sable, 2008-2019 Taurus/Flex/MKT, 2013-2019 Police Interceptor Sedan/Utility, and 2011-2019 Explorer vehicles may exhibit inoperative or intermittent HVAC blower motor function at various fan speed settings. This may be due to a poor electrical connection at the blower motor speed control. If the blower motor speed control is determined to be the causal part, replacement of the electrical connector pigtail harness (14S411) to the blower motor speed control is also recommended to avoid repeat repairs. Refer to Wiring Diagram, Cell 5 for recommended splicing procedures. Refer to Wiring Diagram, Cells 54/55 to obtain the service pigtail connector part number.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:APPLIANCE:AIR CONDITIONER.
Source record 10155565 at NHTSANHTSA communication ID: 10153970
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2019 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 or no modem electronic serial number (ESN) displayed. To correct this condition prior to programing remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229.
Source components: ELECTRICAL SYSTEM · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
Source record 10153970 at NHTSANHTSA communication ID: 10153969
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2012-2019 Vehicles may require repairs to the Smartlink system. Smartlink is a Ford Licensed Accessory which has a warranty provided by the accessory manufacturer. Warranty replacement parts for Smartlink that are ordered through Ford are not reimbursable through the Ford Motor Company warranty system. Please see the Warranty and Policy Manual for further information on Ford Licensed Accessories.
Source components: EQUIPMENT.
Source record 10153969 at NHTSANHTSA communication ID: 10153923
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2019 Explorer vehicles may exhibit a heated lower front seat cushion that does not operate properly after turning the ignition on after a remote start event. To temporarily resolve the concern, the heated seat control switch may be cycled off and then back on. Do not attempt any repairs at this time. Engineering is investigating. To assist with the investigation, use the Report a Vehicle Concern link at the bottom of the OASIS report and fill out the form. Monitor OASIS for updates.
Source components: SEATS:FRONT ASSEMBLY:SEAT HEATER/COOLER.
Source record 10153923 at NHTSANHTSA communication ID: 10153921
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2019 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 or no modem electronic serial number (ESN) displayed. To correct this condition, remove the TCU fuse for 5 minutes prior to programing. Delete all previous session files for the vehicle and do not install the TCU fuse until a new IDS session has been started. Once the new session has been started and the fuse reinstalled, the TCU can be programmed. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual (WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
Source record 10153921 at NHTSANHTSA communication ID: 10153929
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2019 Explorer vehicles built on or before 13-Nov-2018 equipped with a 4G telematics control unit (TCU) modem may exhibit an Acquiring Signal message with a loss of satellite radio reception while driving in unobstructed areas. Follow the Service Procedure steps to correct the condition.
Source components: EQUIPMENT.
Source record 10153929 at NHTSANHTSA communication ID: 10153948
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2019 Ford and Lincoln vehicles equipped with SYNC 3 and a 6, 8 or 10 inch screen may show a pop-up message every key cycle that states 'SYNC can check for updates when connected to a WiFi network'. To remove the inconvenience of the pop-up the customer can either connect to a trusted WiFi network to complete the setup process or turn off WiFi in the WiFi settings located under the Settings menu. Adjusting the setting for the customer is not a warrantable defect.
Source components: ELECTRICAL SYSTEM.
Source record 10153948 at NHTSANHTSA communication ID: 10153931
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2018 C-Max, 2013-2019 Escape/Fusion/MKZ, 2015-2018 Focus, 2015-2019 Edge/F150/MKC/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017 Super Duty, 2018-2019 EcoSport/Expedition, and 2019 Nautilus vehicles may experience seat pan looseness, lateral movement, or clunk/thump noise on turns. Follow the Service Procedure steps to correct the condition.
Source components: EQUIPMENT · SEATS.
Source record 10153931 at NHTSANHTSA communication ID: 10152473
NHTSA source summary · Original PDF not reviewed by Recallfolio
For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. For all turbocharged engine applications, the turbocharger oil supply filter (6C683 gas engine/6L625 connector style or 6A968 diesel engine) must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.
Source components: ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER.
Source record 10152473 at NHTSANHTSA communication ID: 10152469
NHTSA source summary · Original PDF not reviewed by Recallfolio
On 2019 Explorer vehicles equipped with a 2.3L EcoBoost engine, the engine cover has been deleted. The vehicle is not mis-built. The addition of any parts would not be considered a warrantable repair. Do not submit a claim for this condition.
Source components: ENGINE · EQUIPMENT.
Source record 10152469 at NHTSANHTSA communication ID: 10152466
NHTSA source summary · Original PDF not reviewed by Recallfolio
2013-2019 vehicles equipped with a LKS system with customer complaints of steering wheel vibration, steering pull or vehicle drift may be due to an alert and/or steering aid input from the LKS. The LKS system detects unintentional drifting toward the outside of the lane and alerts and/or aids vehicle to stay in the lane. Be sure the customer understands how the lane departure warning feature settings work for Alert (steering wheel vibration) and Aid (steering input toward lane center). Further information on the LKS can be found in the owners manual. If the customers concern is due to the LKS functioning as intended, do not attempt to repair.
Source components: STEERING · STEERING: STEERING WHEEL/HANDLE BAR.
Source record 10152466 at NHTSANHTSA communication ID: 10152465
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2019 Explorers equipped with the power folding 3rd row seat may experience a seat that will not latch/unlatch from folded or normal positions. This may be due to misalignment between the seat latch and the anchor bracket or misalignment between the load floor support and the load floor panel. If the seats attempt to move and stop, attempt to neutralize the anchor brackets and load floor support brackets to improve latch alignment before replacing any parts. Refer to Workshop Manual (WSM) Section 501-10C for torque specifications.
Source components: LATCHES/LOCKS/LINKAGES · SEATS.
Source record 10152465 at NHTSANHTSA communication ID: 10149778
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2019 Police Interceptor Sedan and Utility vehicles may exhibit a reduced top speed after a transmission fluid service with unapproved fluid. The use of unapproved fluid or improper transmission fluid level can lead to reduced vehicle performance and transmission damage that is not covered under warranty. Use only Mercon LV Automatic Transmission Fluid, XT-10-QLVC (US), CXT-10-LV12 (Canada). Use only the Transmission Fluid Exchanger process when performing service intervals. Check and adjust transmission fluid level only at normal operating temperatures of 82?C-93?C (180?F-200?F). The fluid adjustment procedure requires using the appropriate Ford scan tool or equivalent to verify fluid temperature. For optimum performance at high speeds, adjust fluid level to the top of the "MIN" mark on the dipstick.
Source components: POWER TRAIN.
Source record 10149778 at NHTSANHTSA communication ID: 10149766
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2019 Police Interceptor Utility vehicles may have an illuminated MIL with ambient air temperature (AAT) sensor DTC P0073. During the installation of certain police accessories by non-Ford vehicle upfitters, wiring connector C134 may have been left disconnected following the removal and installation of the front bumper cover. If this issue is noted, first check C134 before beginning other diagnostic steps. Reconnecting C134 due to improper reassembly by an outside supplier is not a warrantable repair.
Source components: EQUIPMENT.
Source record 10149766 at NHTSA