2018 Ford EXPLORER Manufacturer communications & TSBs.Page 2
Original record summaries, dates and identifiers for this model-year. Records 101–190 of 190, ordered newest first. Dated records on this page: Oct 6, 2017–Jun 20, 2019.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Jun 20, 2019Service Bulletin/Repair Instructions
SSM 48049
NHTSA communication ID: 10162086
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2017 F-150/Mustang, 2015-2018 Edge/MKC, 2016-2018 MKX, 2013-2018 Explorer/Taurus/Flex/MKT, and 2017-2018 Fusion/MKZ/Continental vehicles built on or before 19-Oct-2017 may exhibit an inoperative adaptive cruise control, collision warning, and/or collision avoidance system with a Pre-Collision Assist Not Available, Collision Warning Not Available, and/or Adaptive Cruise Fault message present in the instrument panel cluster (IPC) and diagnostic trouble code (DTC) U3000:49 present in the cruise control module (CCM). To resolve the condition, reprogram the CCM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 9E731 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2019 Explorer/Flex/Taurus/MKT vehicles equipped with a 3.5L EcoBoost engine may exhibit an illuminated malfunction indicator lamp (MIL), powertrain malfunction (wrench) lamp, Service AdvanceTrac message, Hill Start Assist Not Available message, and/or lack of power with diagnostic trouble codes (DTCs) P0107, P0108 and/or P0109 present. This may be due to a faulty manifold absolute pressure and temperature (MAPT) sensor. To correct the condition, follow the Service Procedure steps to diagnose and replace the MAPT sensor.
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2019 Explorer vehicles equipped with a 2.3L EcoBoost engine may exhibit a squeal noise from the accessory drive belt, illuminated charging system indicator, and/or damaged alternator pulley. Accessory drive belt DA8Z-8620-G has been released to eliminate this noise and alternator pulley damage. Refer to Workshop Manual (WSM), Section 303-05 for the removal and installation procedure. For claiming, use causal part 8620 and applicable labor operations in Section 06 of the Service Labor Time Standards (SLTS) Manual.
Source components: ENGINE · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
On vehicles equipped with an automatic transmission it is imperative that the converter pilot hub be greased with Motorcraft Multi-Purpose Grease Spray XL-5-A even if grease was not applied from the factory. Also verify that the engine/transmission alignment dowel pins are present as well as the engine crankshaft dowel pin, if equipped, when installing the transmission. Failure to adequately lubricate the converter hub greatly increases the likelihood of the flexplate cracking in the future. Missing dowels may cause a misalignment issue also resulting in a premature failure. Refer to Workshop Manual (WSM), Section 307-01.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2019 vehicles equipped with a EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2019 Explorer vehicles may exhibit a loose cushion cover corner and/or exposed foam on the 2nd row left 60 percent seat. The left 2nd row 60 percent seat cushion cover is a different design from the right 2nd row 40 percent cushion cover and the two are not comparable. The right seat trim wraps under the seat and is closed off while the left side is not closed off and may appear loose. This is normal appearance and no repairs should be performed. If the seat foam is exposed, the foam can be tucked upward and the cushion cover refitted to conceal the foam. The seat cushion cover and/or foam should not be replaced for either condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SSM 47948 - 2010-2019 Various Vehicles - Turbocharged Engines - Oil Supply Filter Replacement When Replacing The Turbocharger Or The Turbocharger Oil Supply Tube For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. When specified in the WSM, the turbocharger oil supply filter must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2019 vehicles equipped with a EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:APPLIANCE:AIR CONDITIONER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SSM 47926 - 2018-2019 F-150/Expedition/Navigator/Transit/Explorer - Illuminated MalfunctionIndicator Lamp (MIL) With Diagnostic Trouble Code (DTC) P025A Some 2018-2019 F-150, Expedition, Navigator, Transit and Explorer vehicles may exhibit an illuminated MIL with DTC P025A stored in the powertrain control module (PCM). This may be due to an intermittent or partial disconnect of the harnessto the fuel pump driver module (FPDM) connector. Confirm FPDM connector (F-150 C4336, Expedition/Navigator C433, Transit C433, Explorer C3239) is fully seated prior to performing PC/ED diagnostics or replacing any components. APPLICABLE VEHICLES
Source components: ELECTRICAL SYSTEM · FUEL SYSTEM, GASOLINE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SSM 47914 - 2016-2019 Explorer roof rack cap trim clips now available. 2016-2019 Explorer roof rack cap clips are now available as a separate part. It is no longer necessary to order a complete roof rack rail to obtain the cap retainer clips. To correct loose roof rack caps or broken or missing clips, order part number FB5Z-7851050-A. Ensure roof rails are properly torqued to 55 in/lbs (6.2 Nm) and that power tools are not used for installation as over-torqueing may cause warpage and poor fitment.
Source components: STRUCTURE · STRUCTURE:BODY:ROOF AND PILLARS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2019 F-Super Duty, 2017-2019 Continental, and 2016-2018 Explorer/Police Interceptor Utility vehicles may exhibit a crank/no start condition, inoperative trailer tow lighting and/or inoperative power telescoping mirrors. This may be due to a concern within the battery junction box (BJB) relay module. A lower level service part has been released to allow for replacement of just the BJB relay module instead of the BJB harness. F-Super Duty part number HU5Z-14A067-A, Continental part number GU5Z-14A067-C, Explorer part number FU5Z-14A067-A, Police Interceptor Utility part number GU5Z-14A067-B.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various 2019 vehicles equipped with SYNC 3 and the latest software version 3.2 may exhibit an error message when attempting to update the software to version 3.3. Professional Technician Society (PTS) website may show that software version 3.3 is available for 2019 SYNC 3 vehicles. Do not carry out this update as it may lead to a hardware error message. Engineering is investigating, monitor OASIS for updates.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:SOFTWARE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2017 vehicles may experience a no crank concern due to a security access key table error. When attempting to program keys or perform a parameter reset, the procedure may fail and the Integrated Diagnostic System (IDS) scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the Body Control Module (BCM) is internally faulted and requires replacement. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2017 vehicles may experience a no crank concern due to a security access key table error. When attempting to program keys or perform a parameter reset, the procedure may fail and the Integrated Diagnostic System (IDS) scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the Body Control Module (BCM) is internally faulted and requires replacement. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2019 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 or no modem electronic serial number (ESN) displayed. To correct this condition prior to programing remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2019 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 or no modem electronic serial number (ESN) displayed. To correct this condition prior to programing remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2019 Explorer, 2016-2018 MKX, 2019 Edge/Nautilus, 2017-2019 Fusion/MKZ, and 2018-2019 F-150/Mustang/Expedition/Navigator vehicles equipped with climate controlled seats may exhibit a buzzing noise from the front seats, front seats too warm, and/or inoperative climate controlled front seats. DTCs B14BA:13, B1154:4B, and/or B14B9:13 may also be present. This may be due to loose terminal pin fit on the driver seat module (DSM) connector C341D (16 pin). If a loose terminal pin fit condition is found during normal diagnostics per Workshop Manual (WSM), Section 501-10, a new service pigtail connector (part number 3U2Z-14S411-BRAB) is available. Refer to Wiring Diagram, Cell 119 to make sure C341D is a 16 pin connector and not a 20 pin connector. Refer to Wiring Diagram, Cell 5 for the recommended splicing procedures.
Source components: ELECTRICAL SYSTEM · SEATS · SEATS:FRONT ASSEMBLY:SEAT HEATER/COOLER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2019 Explorer, 2016-2018 MKX, 2019 Edge/Nautilus, 2017-2019 Fusion/MKZ, and 2018-2019 F-150/Mustang/Expedition/Navigator vehicles equipped with climate controlled seats may exhibit a buzzing noise from the front seats, front seats too warm, and/or inoperative climate controlled front seats. DTCs B14BA:13, B1154:4B, and/or B14B9:13 may also be present. This may be due to loose terminal pin fit on the driver seat module (DSM) connector C341D (16 pin). If a loose terminal pin fit condition is found during normal diagnostics per Workshop Manual (WSM), Section 501-10, a new service pigtail connector (part number 3U2Z-14S411-BRAB) is available. Refer to Wiring Diagram, Cell 119 to make sure C341D is a 16 pin connector and not a 20 pin connector. Refer to Wiring Diagram, Cell 5 for the recommended splicing procedures.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2011-2019 Explorer and 2013-2019 Police Interceptor Utility vehicles may exhibit a detached center console rear cup holder and/or the cover panel detached from the rear cup holder. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2011-2019 Explorer and 2013-2019 Police Interceptor Utility vehicles may exhibit a detached center console rear cup holder and/or the cover panel detached from the rear cup holder. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2009-2017 Expedition/Navigator, 2009-2014 F-150/Mustang, 2008-2009 Sable, 2008-2019 Taurus/Flex/MKT, 2013-2019 Police Interceptor Sedan/Utility, and 2011-2019 Explorer vehicles may exhibit inoperative or intermittent HVAC blower motor function at various fan speed settings. This may be due to a poor electrical connection at the blower motor speed control. If the blower motor speed control is determined to be the causal part, replacement of the electrical connector pigtail harness (14S411) to the blower motor speed control is also recommended to avoid repeat repairs. Refer to Wiring Diagram, Cell 5 for recommended splicing procedures. Refer to Wiring Diagram, Cells 54/55 to obtain the service pigtail connector part number.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · EQUIPMENT:APPLIANCE:AIR CONDITIONER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2000 and newer Ford, Lincoln and Mercury vehicles equipped with aluminum body panels may exhibit corrosion concerns appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended. Follow the Service Procedure steps to correct the condition
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2009-2017 Expedition/Navigator, 2009-2014 F-150/Mustang, 2008-2009 Sable, 2008-2019 Taurus/Flex/MKT, 2013-2019 Police Interceptor Sedan/Utility, and 2011-2019 Explorer vehicles may exhibit inoperative or intermittent HVAC blower motor function at various fan speed settings. This may be due to a poor electrical connection at the blower motor speed control. If the blower motor speed control is determined to be the causal part, replacement of the electrical connector pigtail harness (14S411) to the blower motor speed control is also recommended to avoid repeat repairs. Refer to Wiring Diagram, Cell 5 for recommended splicing procedures. Refer to Wiring Diagram, Cells 54/55 to obtain the service pigtail connector part number.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:APPLIANCE:AIR CONDITIONER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2000 and newer Ford, Lincoln and Mercury vehicles equipped with aluminum body panels may exhibit corrosion concerns appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended. Follow the Service Procedure steps to correct the condition
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some all-wheel drive (AWD) 2013-2018 Escape vehicles equipped with 1.5L/1.6L/2.0L EcoBoost/Fusion vehicles equipped with 2.0L/2.7L EcoBoost/MKZ vehicles equipped with 2.0L EcoBoost, 2017-18 MKZ vehicles equipped with 3.0L EcoBoost, 2015-2018 MKC vehicles equipped with 2.0L/2.3L EcoBoost/Edge vehicles equipped with 2.0L/2.7L EcoBoost, 2016-2018 MKX vehicles equipped with 2.0L and 2.7L EcoBoost/Explorer vehicles equipped with 2.3L EcoBoost/Focus RS equipped with 2.3L EcoBoost, and 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost may exhibit a dark black fluid leak from the right side transfer case intermediate shaft seal. Follow the Service Procedure steps to correct the condition.
Source components: POWER TRAIN · POWER TRAIN:AXLE ASSEMBLY:AXLE SHAFT:SEAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some all-wheel drive (AWD) 2013-2018 Escape vehicles equipped with 1.5L/1.6L/2.0L EcoBoost/Fusion vehicles equipped with 2.0L/2.7L EcoBoost/MKZ vehicles equipped with 2.0L EcoBoost, 2017-18 MKZ vehicles equipped with 3.0L EcoBoost, 2015-2018 MKC vehicles equipped with 2.0L/2.3L EcoBoost/Edge vehicles equipped with 2.0L/2.7L EcoBoost, 2016-2018 MKX vehicles equipped with 2.0L and 2.7L EcoBoost/Explorer vehicles equipped with 2.3L EcoBoost/Focus RS equipped with 2.3L EcoBoost, and 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost may exhibit a dark black fluid leak from the right side transfer case intermediate shaft seal. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2019 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 or no modem electronic serial number (ESN) displayed. To correct this condition prior to programing remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229.
Source components: ELECTRICAL SYSTEM · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2012-2019 Vehicles may require repairs to the Smartlink system. Smartlink is a Ford Licensed Accessory which has a warranty provided by the accessory manufacturer. Warranty replacement parts for Smartlink that are ordered through Ford are not reimbursable through the Ford Motor Company warranty system. Please see the Warranty and Policy Manual for further information on Ford Licensed Accessories.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2019 Explorer vehicles may exhibit a heated lower front seat cushion that does not operate properly after turning the ignition on after a remote start event. To temporarily resolve the concern, the heated seat control switch may be cycled off and then back on. Do not attempt any repairs at this time. Engineering is investigating. To assist with the investigation, use the Report a Vehicle Concern link at the bottom of the OASIS report and fill out the form. Monitor OASIS for updates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2019 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 or no modem electronic serial number (ESN) displayed. To correct this condition, remove the TCU fuse for 5 minutes prior to programing. Delete all previous session files for the vehicle and do not install the TCU fuse until a new IDS session has been started. Once the new session has been started and the fuse reinstalled, the TCU can be programmed. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual (WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2019 Explorer vehicles built on or before 13-Nov-2018 equipped with a 4G telematics control unit (TCU) modem may exhibit an Acquiring Signal message with a loss of satellite radio reception while driving in unobstructed areas. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2019 Ford and Lincoln vehicles equipped with SYNC 3 and a 6, 8 or 10 inch screen may show a pop-up message every key cycle that states 'SYNC can check for updates when connected to a WiFi network'. To remove the inconvenience of the pop-up the customer can either connect to a trusted WiFi network to complete the setup process or turn off WiFi in the WiFi settings located under the Settings menu. Adjusting the setting for the customer is not a warrantable defect.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2018 C-Max, 2013-2019 Escape/Fusion/MKZ, 2015-2018 Focus, 2015-2019 Edge/F150/MKC/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017 Super Duty, 2018-2019 EcoSport/Expedition, and 2019 Nautilus vehicles may experience seat pan looseness, lateral movement, or clunk/thump noise on turns. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. For all turbocharged engine applications, the turbocharger oil supply filter (6C683 gas engine/6L625 connector style or 6A968 diesel engine) must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.
Source components: ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2013-2019 vehicles equipped with a LKS system with customer complaints of steering wheel vibration, steering pull or vehicle drift may be due to an alert and/or steering aid input from the LKS. The LKS system detects unintentional drifting toward the outside of the lane and alerts and/or aids vehicle to stay in the lane. Be sure the customer understands how the lane departure warning feature settings work for Alert (steering wheel vibration) and Aid (steering input toward lane center). Further information on the LKS can be found in the owners manual. If the customers concern is due to the LKS functioning as intended, do not attempt to repair.
Source components: STEERING · STEERING: STEERING WHEEL/HANDLE BAR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2019 Explorers equipped with the power folding 3rd row seat may experience a seat that will not latch/unlatch from folded or normal positions. This may be due to misalignment between the seat latch and the anchor bracket or misalignment between the load floor support and the load floor panel. If the seats attempt to move and stop, attempt to neutralize the anchor brackets and load floor support brackets to improve latch alignment before replacing any parts. Refer to Workshop Manual (WSM) Section 501-10C for torque specifications.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When connecting the Vehicle Communication Module (VCM) and Integrated Diagnostic System (IDS) or Ford Diagnosis and Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic trouble codes (DTCs), no start, no crank conditions or the IPC inoperative. If a vehicle displays these issues, disconnect the equipment from the DLC and disconnect the vehicle battery. Wait 10 minutes and reinstall with the ignition off. Clear any DTCs present and retest.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2018 Explorer vehicles built on or before 07-Aug-2018 may automatically switch from A/C to heat and defrost after 1 minute during a remote start event when the customer expects the A/C to remain on. To resolve the concern, reprogram the heating, ventilation and air conditioning (HVAC) control module using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 19980 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:APPLIANCE:AIR CONDITIONER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2018 Model Year Explorer And Police Interceptor Utility Vehicles Key Off Load Battery Drain Certain 2018 Model Year MKZ Hybrid Vehicles Equipped with the Magnetic Appearance Package - Accelerator Pedal and Brake Pedal Cover Replacement
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2019 Police Interceptor Sedan and Utility vehicles may exhibit a reduced top speed after a transmission fluid service with unapproved fluid. The use of unapproved fluid or improper transmission fluid level can lead to reduced vehicle performance and transmission damage that is not covered under warranty. Use only Mercon LV Automatic Transmission Fluid, XT-10-QLVC (US), CXT-10-LV12 (Canada). Use only the Transmission Fluid Exchanger process when performing service intervals. Check and adjust transmission fluid level only at normal operating temperatures of 82?C-93?C (180?F-200?F). The fluid adjustment procedure requires using the appropriate Ford scan tool or equivalent to verify fluid temperature. For optimum performance at high speeds, adjust fluid level to the top of the "MIN" mark on the dipstick.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2018 Explorer vehicles equipped with a 110V power outlet may exhibit a high pitched buzzing or ringing noise from the right side front interior area while the engine is running. If replacing the DC/AC inverter does not resolve the concern, replace the fuel pump control module with part number FU5Z-9D370-B. Inspect the new replacement module and ensure the engineering part number suffix shows "LA" before installing. If the fuel pump control module has an engineering part number suffix "JA", the part should be returned via the normal part return process. For claiming, use causal part 9D370 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual. Engineering is investigating, monitor OASIS for updates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2018 Ford and Lincoln vehicles equipped with SYNC 3 may exhibit the Android Auto Preference menu selection is not present after an update to version 3.0 software. In prior versions of SYNC 3 software this menu was present, however in version 3.0 software the Android Auto Preference menu will only show up once an Android Phone has been initially connected to SYNC. This an operating characteristic of the Android Auto application after the SYNC 3.0 update and no repairs should be attempted.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018 Explorer, Expedition, F150 excluding Raptor fleet vehicles equipped with a telematics control unit (TCU) may exhibit incomplete Ford Telematics service subscription activation, inability to remotely interface with a vehicle, and/or not receiving fleet alerts. Reprogram the TCU using the appropriate Ford scan tool at the latest software level. Fleet vehicle and TCU type can be identified in the Vehicle Information section of OASIS. TCU will be listed as 4G SYNC Connect. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2019 Police Interceptor Utility vehicles may have an illuminated MIL with ambient air temperature (AAT) sensor DTC P0073. During the installation of certain police accessories by non-Ford vehicle upfitters, wiring connector C134 may have been left disconnected following the removal and installation of the front bumper cover. If this issue is noted, first check C134 before beginning other diagnostic steps. Reconnecting C134 due to improper reassembly by an outside supplier is not a warrantable repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018 Explorer/Police Interceptor Utility vehicles equipped with Police, Base 100A, or XLT 200A package trim levels (Type 1 analog cluster in the Owner's Manual) built on 08-May-2018 and through 05-Aug-2018 may exhibit a parasitic battery drain of approximately 250 milliamps with the instrument panel cluster (IPC) possibly staying awake with the key off. This may result in a no crank/no start/discharged battery condition. To resolve the concern, reprogram the IPC using the latest software level of the appropriate Ford diagnostic scan tool. Make sure the vehicle is connected to a battery charger. For claiming, use causal part 10849 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018 Explorer and Escape vehicles equipped with a 4G TCU modem may exhibit an Acquiring Signal message with a loss of satellite radio reception while driving in unobstructed areas. If normal Workshop Manual (WSM) diagnosis and testing does not indicate a fault and no diagnostic trouble codes (DTCs) are stored, do not attempt any repairs at this time. Engineering is investigating, monitor OASIS for updates. To assist with the investigation, use the Report A Vehicle Concern link at the bottom of the OASIS report and complete the form.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018 F-Superduty/F-150/Explorer/Taurus/Flex/MKT/Expedition/Navigator vehicles built on 8-Mar-2018 and through 18-Jun-2018 may exhibit a soft brake pedal and/or long brake pedal travel. Bleed the brake system per Workshop Manual (WSM), Section 206-00. For claiming, use causal part 2552 and applicable labor operations in Section 02 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When connecting the Vehicle Communication Module (VCM) and Integrated Diagnostic System (IDS) or Ford Diagnosis and Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic trouble codes (DTCs), no start, no crank conditions or the IPC inoperative. If a vehicle displays these issues, disconnect the equipment from the DLC and disconnect the vehicle battery. Wait 10 minutes and reinstall with the ignition off. Clear any DTCs present and retest.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018 Explorer/Police Interceptor Utility vehicles equipped with Police, Base 100A, or XLT 200A package trim levels (Type 1 analog cluster in the Owner's Manual) built on 08-May-2018 and through 05-Aug-2018 may exhibit a parasitic battery drain of approximately 250 milliamps with the instrument panel cluster (IPC) possibly staying awake with the key off. This may result in a no crank/no start/discharged battery condition. To resolve the concern, reprogram the IPC using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 10849 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2018 Escape vehicles equipped with 1.5L/1.6L/2.0L EcoBoost, 2013-2018 Fusion vehicles equipped with 2.0L/2.7L EcoBoost, 2013-2018 MKZ vehicles equipped with 2.0L EcoBoost, 2017-18 MKZ vehicles equipped with 3.0L EcoBoost, 2015-2018 MKC vehicles equipped with 2.0L/2.3L EcoBoost, 2015-2018 Edge vehicles equipped with 2.0L/2.7L EcoBoost, 2016-2018 MKX vehicles equipped with 2.0L and 2.7L EcoBoost, 2016-2018 Explorer vehicles equipped with 2.3L EcoBoost, 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost and 2016-2018 Focus RS equipped with 2.3L EcoBoost may exhibit a dark black fluid leak from the right side transfer case intermediate shaft seal. Follow the Service Procedure to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018 F-Superduty/F-150/Explorer/Taurus/Flex/MKT/Fiesta vehicles built on 8-Mar-2018 and through 18-Jun-2018 may exhibit a soft brake pedal and/or long brake pedal travel. Bleed the brake system per Workshop Manual (WSM), Section 206-00. For claiming, use causal part BRAKE and applicable labor operations in Section 02 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018 Explorer vehicles equipped with a 4G TCU modem may exhibit an Acquiring Signal message with a loss of satellite radio reception while driving in unobstructed areas. If normal Workshop Manual (WSM) diagnosis and testing does not indicate a fault and no diagnostic trouble codes (DTCs) are stored, do not attempt any repairs at this time. Engineering is investigating, monitor OASIS for updates. To assist with the investigation, use the Report A Vehicle Concern link at the bottom of the OASIS report and complete the form.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018 F-Superduty/F-150/Explorer/Taurus/Flex/MKT vehicles built on 8-Mar-2018 and through 18-Jun-2018 may exhibit a soft brake pedal and/or long brake pedal travel. Bleed the brake system per Workshop Manual (WSM), Section 206-00. For claiming, use causal part BRAKE and applicable labor operations in Section 02 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2018 Ford and Lincoln vehicles equipped with SYNC 3 not at the latest software level may exhibit Various Performance Related concerns such as Display Operation, Navigation, Voice Recognition, Phone Pairing, Applink, Travel Link, Slow System Response, etc. Check for SYNC software update under the OASIS Tab SYNC selection. If an update is available refer to WSM, Section 415-00 and update the APIM software. After Installation, complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018 Explorers equipped with Platinum trim level built on 25-Oct-2017 and through 01-May-2018 may intermittently display a "Hill Descent Control Fault" message in the IPC briefly at start up without any diagnostic trouble codes (DTCs) stored in the anti-lock brake system (ABS) module. Reprogram the IPC using the appropriate Ford scan tool or equivalent release 110.03 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. For claiming, use causal part 10849 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: ELECTRICAL SYSTEM · SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2018 Explorers equipped with the power folding 3rd row seat may experience a seat that will not latch/unlatch from folded or normal positions. This may be due to misalignment between the seat latch and the anchor bracket or misalignment between the load floor support and the load floor panel. If the seats attempt to move and stop, attempt to neutralize the anchor brackets and load floor support brackets to improve latch alignment before replacing any parts. Refer to Workshop Manual (WSM) Section 501-10C for torque specifications.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2018 Explorer vehicles may automatically switch from A/C to heat and defrost after 1 minute during a remote start idle when the customer expects the A/C remain on. The system will return to normal operation after the ignition is turned to the run position. Do not attempt any repairs at this time. Engineering is investigating, monitor OASIS for updates. To assist with the investigation, use the Report A Vehicle Concern link at the bottom of the OASIS report to complete the form.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2018 Ford and Lincoln vehicles with SYNC 3 may exhibit an intermittent blue or black screen. Check for SYNC software update under the OASIS Tab SYNC selection. If update is available refer to WSM, Section 415-00 and update APIM software. After Installation Complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various 2016-2018 vehicles with SYNC 3 may experience a touch screen that does not respond to any input. Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
RKE stand alone key fobs can be added to 2016 and newer Police Utility vehicles not previously equipped with them. To program the fobs, start an IDS session and enter the Red Toolbox > Module Programming > Programmable Parameters > Police Mode > Remote Keyfob Learn > Enable. Next, refer to the RKE Transmitter Programming procedure listed in Workshop Manual (WSM), Section 501-14 > General Procedures to program the fobs. If the RKE fobs fail to program, verify that the fobs are the correct part number. If the fobs are correct for the vehicle, then refer to the inoperative key fob diagnostics outlined in WSM, Section 501-14. This procedure and part numbers do not apply to 2015 and previous model year Police Utility vehicles. Blue lift gate button fobs are part No. GB5Z-15K601-C and red panic button fobs are part No. GB5Z-15K601-A.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2018 Police Interceptor Utility vehicles equipped with a 3.7L twin independent variable camshaft timing (TiVCT) engine may exhibit an engine vibration and/or the engine mount leaking fluid. A revised engine mount (GB5Z-6038-A) has been released to address this condition. For claiming, use causal part 6038 and applicable labor operations in Section 06 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018 Explorers equipped with Platinum trim level built on 25-Oct-2017 and through 01-May-2018 may intermittently display a "Hill Descent Control Fault" message in the IPC briefly at start up without any diagnostic trouble codes (DTCs) stored in the anti-lock brake system (ABS) module. Do not attempt any repairs at this time. Engineering is investigating, monitor OASIS for updates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018 F-150, Expedition, Navigator, Transit and Explorer vehicles may exhibit an illuminated MIL with DTC P025A stored in the powertrain control module (PCM). This may be due to an intermittent or partial disconnect of the harness to the fuel pump driver module (FPDM) connector. Confirm FPDM connector (F-150 C4336, Expedition/Navigator C433, Transit C433, Explorer C3239) is fully seated prior to performing PC/ED diagnostics or replacing any components. Engineering is investigating, monitor OASIS for updates.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 or no modem electronic serial number (ESN) displayed. To correct this condition, remove the TCU fuse for 5 minutes then reinstall. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual (WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various 2018 vehicles equipped with SYNC or SYNC 3 automatic system updates via WI-FI are unable to connect to the vehicles 4G WI-FI Hotspot. SYNC/SYNC3 with automatic system updates do not support connecting SYNC to the vehicles internal 4G WI-FI Hotspot if equipped. The SYNC automatic update feature must be connected to an external Wi-Fi source to function properly. No repairs should be made in attempt to correct this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Replacing the original equipment SYNC/Navigation system with either an aftermarket SYNC/Navigation kit or modifying original SYNC/Navigation parts to provide additional features is not recommended nor supported on any Ford, Mercury or Lincoln vehicle. Only approved Genuine Ford accessories or originally installed systems are supported and certified to function correctly with other vehicle systems. If you suspect a system has been modified, the following resources can be used to verify original equipment: Monroney Label (Window Sticker), Professional Technician Society (PTS) OASIS tab select SYNC or HVBOM. For Genuine Ford accessories use: PTS Workshop Tab select Dealer Installed Accessory or Accessory Installation.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 Explorer vehicles equipped with Hankook brand tires may exhibit tread wear that is not the result of vehicle alignment concerns. For customer satisfaction, Hankook is offering pro-rated tire replacement for vehicles with less than 36,000 Miles. This program is managed by Hankook Tire America Corp. and not claimed under Ford new vehicle limited warranty. If the tire side wall is marked as: 255/50R20 105H Ventus S1 Noble 2, contact Hankook Technical Service for possible pro-rated tire replacement. Refer to FMCDealer.com Tire Page for details and Hankook contact information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2018 Ford and Lincoln vehicles equipped with SYNC 3 and connected to an iPhone recently upgraded to iOS 11.2.5 may exhibit functional concerns where USB audio playback and App Link will not operate. This may also include, under certain conditions, no Bluetooth streaming. Apple has released iOS 11.2.6 to address this concern. Advise the customer to update the device to iOS 11.2.6 and re-evaluate before performing any diagnosis or repairs for this condition. To check the iOS software level on an Apple iOS device, select Settings > General > About on the device.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2018 Explorer vehicles equipped with automatic temperature control and premium AM/FM/CD may exhibit a broken or missing temperature control switch. The driver and passenger switches are now available separately from the control head. Replacement of the control head assembly is not necessary. The switches are driver and passenger specific and must be installed in the correct location with the red heat indicator facing up. HB5Z-19986-AA - Drivers Side Switch, HB5Z-19986-BA - Passengers Side Switch
NHTSA source summary · Original PDF not reviewed by Recallfolio
2016-2018 Explorer signature lighting is standard equipment on XLT and higher level vehicles. Base model vehicles are not equipped with signature lighting and it is not an option. Base level vehicles without the LED lighting surrounding the headlamps are built correctly and should not be modified by installing the signature lamps. Prior to beginning any diagnostics, verify the proper vehicle model/series utilizing OASIS or referring to Workshop Manual Section 100-01.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2018 Ford and Lincoln Vehicle equipped with SYNC 3 and connected to an iPhone recently upgraded to iOS 11.2.5 may exhibit a concern where USB Audio playback and App Link applications will not function properly. This may also include, under certain conditions, no Bluetooth Streaming. Apple is aware of the issue and is working on a resolution with a future iOS release. No repairs should be performed at this time. To check the iOS software level on an Apple iOS device, select Settings > General > About on the device. Monitor OASIS for updates. Customers can also check Apple Support or connect to iTunes for the latest available iOS release for their phone.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2010-2018 various vehicles equipped with SYNC or SYNC 3 may not function when attempting to find or use the Spotify app via AppLink. As of an update released on 1/15/2018 Spotify will no longer be supporting their AppLink integration. No repair attempts should be attempted to correct this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
When connecting the Vehicle Communication Module (VCM) and Integrated Diagnostic System (IDS) or Ford Diagnosis and Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic trouble codes (DTCs), no start or no crank conditions or the IPC inoperative. For Lincoln vehicles, this information is now listed in the Technical Inspection and Post Road Test Sections of ePDI on the PTS website. If a vehicle displays these issues, disconnect the equipment from the DLC and disconnect the vehicle battery. Wait 10 minutes and reinstall with the ignition off. Clear any DTCs present and retest.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2018 Police Interceptor Utility vehicles may exhibit flickering front amber marker lamps (inboard amber lights under the headlamps) when the engine is running. Before attempting repairs, verify the frequency type using the Integrated Diagnostic System (IDS) or equivalent. The frequency type in police mode programmable parameters must be set to type 2. The engine must be running for the configuration to complete if this parameter is changed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2018 Explorer vehicles equipped with a 2.3L EcoBoost engine built on or before 7-Dec-2017 may exhibit an illuminated MIL with DTC P04DB (crankcase ventilation system disconnected) in the powertrain control module (PCM) memory. Reprogram the PCM using Integrated Diagnostic System (IDS) or Ford J2534 Diagnostic Software (FJDS) release 108.02 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. Calibration files may also be obtained at www.motorcraftservice.com.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2018 Explorer vehicles equipped with a 2.3L EcoBoost engine built on or before 7-Dec-2017 may exhibit an illuminated MIL with DTC P04DB (crankcase ventilation system disconnected) in the powertrain control module (PCM) memory. Reprogram the PCM using Integrated Diagnostic System (IDS) or Ford J2534 Diagnostic Software (FJDS) release 108.02 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. Calibration files may also be obtained at www.motorcraftservice.com.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The Accessory (Wireless) Keyless Entry Keypad can only be used with vehicles that are factory built with Remote Keyless Entry (RKE). The master code for the Accessory (Wireless) Keyless Entry Keypad can be retrieved from FMCDealer - Parts and Service - Parts Product Line Information - Keys/Entry Devices - Aftermarket Keyless Entry Keypad Code Access. Access to this site is granted through Dealer Program Enrollment System (DPES) and Dealer Principal, General Manager or Parts and Service Director can authorize users. Once authorized the retrieval process for master code can be obtained. The master code for the Accessory Keyless Entry Keypad cannot be retrieved from the body control module(BCM) with a diagnostic tool.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2017-2018 Explorer/Taurus vehicles equipped with 3.5L gasoline turbocharged direct injection (GTDI) engine and built on or after 27-Jun-2017 are equipped with a revised rear lower roll restrictor that eliminates the need for the front roll restrictor. The front roll restrictor has been eliminated by design on these vehicle applications even though the brackets may still be present. Do not add the front roll restrictor to units built after this date, as it may negatively impact the noise, vibration and harshness (NVH) attributes.
Source components: ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2018 Explorer vehicles equipped with a 110V power outlet may exhibit a high pitched buzzing or ringing noise from the right side front interior area while the engine is running. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The Accessory (Wireless) Keyless Entry Keypad can only be used with vehicles that are factory built with Remote Keyless Entry (RKE). The master code for the Accessory (Wireless) Keyless Entry Keypad can be retrieved from FMCDealer - Parts and Service - Parts Product Line Information - Keys/Entry Devices - Aftermarket Keyless Entry Keypad Code Access. Access to this site is granted through Dealer Program Enrollment System (DPES) and Dealer Principal, General Manager or Parts and Service Director can authorize users. Once authorized the retrieval process for master code can be obtained. The master code for the Accessory Keyless Entry Keypad cannot be retrieved from the body control module(BCM) with a diagnostic tool.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2017-2018 Explorer/Taurus vehicles equipped with 3.5L gasoline turbocharged direct injection (GTDI) engine and built on or after 27-Jun-2017 are equipped with a revised rear lower roll restrictor that eliminates the need for the front roll restrictor. The front roll restrictor has been eliminated by design on these vehicle applications even though the brackets may still be present. Do not add the front roll restrictor to units built after this date, as it may negatively impact the noise, vibration and harshness (NVH) attributes.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2018 Explorer vehicles equipped with a 110V power outlet may exhibit a high pitched buzzing or ringing noise from the right side front interior area while the engine is running. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2018 Escape/Fusion/MKZ vehicles equipped with 2.5L or 1.5L/2.0L/3.0L Ecoboost engine, 2015-2018 MKC/Edge/Explorer vehicles equipped with 2.0L/2.3L/2.7L EcoBoost engine, 2016-2018 MKX vehicles equipped with 2.7L Ecoboost engine, 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost, and AWD may exhibit a fluid leak from the PTU intermediate shaft seal. Replacement of the intermediate shaft seal seal does not require removal of the PTU and does not require the use of the cover seal and bolt kit (CV6Z-7275-K) to perform the repair. Refer to the Workshop Manual (WSM), Section 308-07.
Source components: ENGINE · POWER TRAIN:TRANSFER CASE (4-WHEEL DRIVE).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2018 Escape/Fusion/MKZ vehicles equipped with 2.5L or 1.5L/2.0L/3.0L Ecoboost engine, 2015-2018 MKC/Edge/Explorer vehicles equipped with 2.0L/2.3L/2.7L EcoBoost engine, 2016-2018 MKX vehicles equipped with 2.7L Ecoboost engine, 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost, and AWD may exhibit a fluid leak from the PTU intermediate shaft seal. Replacement of the intermediate shaft seal seal does not require removal of the PTU and does not require the use of the cover seal and bolt kit (CV6Z-7275-K) to perform the repair. Refer to the Workshop Manual (WSM), Section 308-07.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2018 Ford or Lincoln vehicles equipped with SYNC 3 may exhibit a blank screen or other various SYNC symptoms only when the vehicle is in transport mode. This is due to the power saving features enabled while in transport mode and is beneficial for battery life to keep the vehicle in transport mode until the vehicle is prepped for sale. To prevent a SYNC system lockup during transport mode deactivation, follow the Workshop Manual (WSM) procedure allowing time for the SYNC system to complete all tasks such as fully booting up or powering down and shutting off before moving to the next step of the procedure. If the vehicle exhibits a blank screen or SYNC symptoms after transport mode deactivation, refer to WSM, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 Explorer vehicles equipped with Hankook brand tires may exhibit chipping, cutting and/or unusual or even accelerated tread wear. If the tire side wall is marked as: 255/50R20 105H Ventus S1 Noble 2 contact Hankook Technical Service for possible pro-rated tire replacement. This may not be the result of improper alignment. For Hankook contact information refer to the Tire Warranty information located on FMCDealer.com.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles may exhibit a no start condition with an illuminated malfunction indicator lamp (MIL) and a DTC P161A after PCM replacement. This may be due to the parameter reset procedure not being properly completed. To clear this DTC, use the Ford Integrated Diagnostic System (IDS) service tool or Ford J2534 Diagnostic Software, select - Toolbox - Body - Security - PATS Functions - Parameter Reset. Follow the on-screen instructions to complete the procedure. This procedure will transfer the existing Key ID information between the modules without the need of having 2 programmed PATS keys present. There is no need to program keys when the PCM is going to be replaced. Additional information can be found in the Workshop Manual (WSM), Section 419-01. Missing or lost keys are not warrantable.
Source components: ELECTRICAL SYSTEM · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2018 Ford or Lincoln vehicles equipped with SYNC 3 may exhibit a blank screen or other various SYNC symptoms only when the vehicle is in transport mode. This is due to the power saving features enabled while in transport mode and is beneficial for battery life to keep the vehicle in transport mode until the vehicle is prepped for sale. To prevent a SYNC system lockup during transport mode deactivation, follow the Workshop Manual (WSM) procedure allowing time for the SYNC system to complete all tasks such as fully booting up or powering down and shutting off before moving to the next step of the procedure. If the vehicle exhibits a blank screen or SYNC symptoms after transport mode deactivation, refer to WSM, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.