2024 Ford EXPEDITION Manufacturer communications & TSBs.Page 1
Original record summaries, dates and identifiers for this model-year. Records 1–100 of 106, ordered newest first. Dated records on this page: Feb 1, 2024–Aug 22, 2026.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Aug 22, 2026Service Bulletin/Repair Instructions
SSM 55100
NHTSA communication ID: 11036530
NHTSA source summary · Original PDF not reviewed by Recallfolio
For Various Ford and Lincoln vehicles, if diagnostics lead to the replacement of the front seat cushion cover J-clips, lower-level service parts are now available. Use service part W709919-S901 if the J-clip is completely detached from the seat cover and W715386-S424 if the clip is still partially attached. It is not necessary to replace the seat cover if only the J-clip is separating from the cover. Refer to PTS Home > Technical Assistance > Technical Support Videos > Section 501- Body and Paint > Seat J-Clips. For claiming, use causal parts from list below and labor operations 63100A and 63100A5. Causal Parts for claiming: Bronco/Bronco Sport/Escape/Explorer/Expedition/Navigator: 7862900 or 7862901 F-150/F-Super Duty: 1562900 or 1562901 Ranger/Maverick: 6062900 or 6062901
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles listed in the Model statement above may exhibit a condition where certain devices built on the Android OS platform (including Voxx rear seat entertainment system) indicate they are connected to the vehicles Wi-Fi hotspot, but internet performance is degraded. Symptoms may include no internet access, intermittent connectivity, and/or limited/very low streaming capability. Some websites/apps may partially load while others do not load at all, despite showing Connected. This may be due to the telematics control unit (TCU) software.
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2026 Ford/Lincoln vehicles may exhibit various symptoms including but not limited to the auto start/stop system not operating as intended with a "Check Charging System" message in the instrument panel cluster (IPC) while the charging system is operating properly with no charging related diagnostic trouble codes (DTC) stored. This may be due to someone using an aftermarket programmer to change the body control module (BCM) configuration to disable the auto start/stop system or perform other unsupported programming modifications. To correct this condition on F-150 and Bronco vehicles, download and run the Ford Diagnosis and Repair System (FDRS) application titled "BCM-Charging System Configuration Correction". Running this application will determine if the BCM configuration was modified by the customer and if so, provide the option to return the configuration back to factory settings. For other vehicle models exhibiting concerns related to unsupported aftermarket BCM programming, submit a Technical Support Request (TSR) requesting support to revert the BCM configuration
Source components: ELECTRICAL SYSTEM · FUEL/PROPULSION SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2024 Ford and Lincoln vehicles may exhibit an "Updating SYNC" message on the vehicle center display screen after an over the air (OTA) update. The message can be cleared from the center display screen and SYNC can be used normally, but it will re-appear at every subsequent ignition cycle. Inform customers that engineering is currently working on a software update solution for this condition to be delivered OTA expected in late Q3 2026. Software will update automatically if vehicle connectivity is enabled in the vehicles settings. Monitor Professional Technician System (PTS) for additional information.
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
NEW VEHICLE DELIVERY HOLD - Emissions Recall 26E04 Certain 2021-2025 Model Year F-150, Maverick, Mustang, Ranger, Expedition, Bronco Sport, Explorer, Bronco, Navigator, and Aviator Vehicles Powertrain Control Module Software Update
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin supersedes 26-2241. Reason For Update: update the parts list to correct the claim quantity of the part number JB3Z-4B496-B from 3 to 6. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: * Harsh 3-4, 4-5 upshifts * Harsh 5-3, 4-3 downshifts * Harsh reverse engagements These symptoms may be worse when cold. This may be due to the F clutch friction plates brinelling into the clutch and planetary container cylinder (7B177).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some of the vehicles listed in the model statement above equipped with SYNC4 may experience a blank center display screen or black center display after welcome animation. The rear-view camera will still function when shifting the vehicle to reverse under these conditions.
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022-2024 Expedition equipped with driver's assistance package (minor feature codes DBCBB or DBCBC) may exhibit various driver assistance feature warning messages displayed in the instrument panel cluster (IPC) with various invalid data/lost communication diagnostic trouble codes (DTC) stored in the power steering control module (PSCM) and/or anti-lock brake (ABS) module. To correct this condition, download and run the "IPMA - Image Processing Module A (IMPA) Software Update" application using the latest software level of the Ford Diagnosis and Repair System (FDRS). For claiming, use causal part 14G647 and labor operation MT14G647SSM up to 1.0 hours. <br /><br /> If the IPMA is failing to communicate, download and run the "IPMA - Image Processing Module A (IPMA) Recovery" application in the FDRS scan tool. Select and run the IPMA Recovery Flash Erase option from the menu. Once communication has been restored with the IPMA, download and run the "IPMA - Image Processing Module (IPMA) Alignment" application in the FDRS and download and run the "IPMA - Image Processing Module A (IPMA) Software
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin supersedes 26-2112. Reason For Update: add 2026 model year vehicles, update LV fluid XT-10-QLVC and CXT-10-LV6 description to add "Transfer Case Fluid 4WD Only", and update Step 4 to inspect/replace 7H351 and 7B177 outside of this article. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: - No upshift past second gear - Unable to achieve third gear ratio - Illuminated MIL with DTCs P0757 and P2701 This may be due to a damaged one-way clutch (OWC).
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin supersedes 25-2587. Reason For Update: update the Parts list to add the F-clutch friction plates HL3Z-7B164-D and the F-clutch steel plates PR3Z-7B164-A for the proper vehicle lines, replace the transfer case mounting bolt part number from W714288-S438 to W714288-S437, update the part number W720688-S439 quantity from 2 to 1, update the part number ML3Z-7869-C claim quantity from 2 to 1 (only if necessary), update the description of CXT-10-LV6 and XT-10-QLVC by adding "transfer case fluid, 4WD only", move HL3Z-7A191-B and L1MZ-7F396-A fluid pan gaskets to the parts to inspect and replace list, and remove TL1Z-6775-A self adhesive heat shield from the F-150/Expedition/Navigator parts list as it is not a discard item. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: * Harsh 3-4, 4-5 upshifts * Harsh 5-3, 4-3 downshifts * Harsh reverse engagements These symptoms may be worse when cold. This may be due to the F clutch friction plates brinelling into the clutch and planetary container cylinder (7B177).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various 2020-2026 Ford and Lincoln vehicles equipped with blind spot information system (BLIS) may experience an inoperative blind spot monitoring with a "Blind Spot System Fault" message displayed in the instrument panel cluster (IPC). This may also be accompanied by diagnostic trouble codes (DTCs) B118C:11 and/or B118C:15 stored in the driver door module (DDM), and/or B118D:11 and/or B118D:15 stored in the passenger door module (PDM). This may be due to the wiring connector from the mirror to the BLIS module. If diagnostics lead to an internal mirror wiring harness fault, a new lower level BLIS light pigtail is now released for service. It is not necessary to replace the exterior mirror assembly. Use part number SC3Z-14A411-B to resolve the concern.
Source components: ELECTRICAL SYSTEM · LANE DEPARTURE: BLIND SPOT DETECTION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
For 20212026 vehicles equipped with the 10R80 transmission, a new Transmission Clutch Circuit Leak Test has been introduced in the Ford Diagnosis and Repair System (FDRS). This test utilizes the pressure and vacuum transducer (PVT) when available. When referred to a specific clutch (A-F) test by a pinpoint test in Workshop Manual (WSM), Section 307-01 > Diagnosis and Testing, the Clutch Assembly tests have been updated with a hyperlink to the new Transmission Line Pressure Test - Pressure Vacuum Transducer (PVT) Is Available procedure in WSM, Section 307-01 > General Procedures. This procedure provides instructions to perform the FDRS Transmission Clutch Circuit Leak Test when applicable. The new test improves the accuracy of detecting leaks within transmission fluid circuits and replaces the previous air check method. The previous air check procedure has been shown to produce a high rate of false positives, which may lead to unnecessary repairs when no actual leak is present. Accordingly, the air check procedure is not to be used for diagnosing internal transmission hydraulic leaks or as justification
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles listed in the Model section above may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P2418:72 and/or P2450 stored in the PCM. This may be due to improperly connected evaporative emission line connections inside the fuel tank.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: * Harsh 3-4, 4-5 upshifts * Harsh 5-3, 4-3 downshifts * Harsh reverse engagements These symptoms may be worse when cold. This may be due to the F clutch friction plates brinelling into the clutch and planetary container cylinder (7B177).
Source components: POWER TRAIN · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
For 2021-2026 vehicles equipped with the 10R80 transmission, a new Transmission Clutch Circuit Leak Test has been introduced in the Ford Diagnosis and Repair System (FDRS). This test utilizes the pressure and vacuum transducer (PVT) when available. The Workshop Manual (WSM) has been updated under Section 307-01 > Diagnosis and Testing to include this procedure. The new test improves the accuracy of detecting leaks within transmission fluid circuits and replaces the previous air check method.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin supersedes TSB 26-2059. Reason For Update: To add missing labor operations. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: - No upshift past second gear - Unable to achieve third gear ratio - Illuminated malfunction indicator lamp (MIL) with DTCs P0757 and P2701 This may be due to a damaged one-way clutch (OWC).
Source components: FUEL/PROPULSION SYSTEM · POWER TRAIN · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin supersedes TSB 25-2423. Reason For Update: Replace the incorrect acronym SOWC with the correct acronym OWC. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: - No upshift past second gear - Unable to achieve third gear ratio - Illuminated malfunction indicator lamp (MIL) with DTCs P0757 and P2701 This may be due to a damaged one-way clutch (OWC).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022-2024 Expedition/Navigator vehicles equipped with minor feature codes DBCBB or DBCBC may exhibit various driver assistance feature warning messages displayed in the instrument panel cluster (IPC). Additionally, some modules may store diagnostic trouble codes (DTC) related to invalid data or lost communication. This condition may be due to the software in the image processing module A (IPMA). If the IPMA is currently failing to communicate, download and run the "IPMA - Image Processing Module A (IPMA) Recovery" application in the Ford Diagnosis and Repair System (FDRS) scan tool. Select and run the IPMA Recovery Flash Erase option from the menu. If the driver assistance warnings and/or symptoms are intermittent, and possibly not failing during the dealership visit, download and run the "IPMA - Image Processing Module A (IPMA) Recovery" application in the FDRS scan tool. Select and run the GWM Ethernet Update option from the menu. If IPMA communication had to be restored using the recovery application, download and run the "IPMA - Image Processing Module (IPMA) Alignment" application
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2024-2025 F-150, Expedition/Navigator, Escape/Corsair, Bronco, Explorer, Mustang, Maverick vehicles equipped with a 1.5/2.0/2.3/3.5L EcoBoost engine and built on 01-Oct-2024 and through 31-May-2025 may exhibit an extended crank condition, strong fuel smell in the engine oil, high engine oil level and/or may have various drivability diagnostic trouble codes (DTCs) stored in the powertrain control module (PCM) with an illuminated malfunction indicator lamp (MIL). This may be due to an internal fuel leak of the high-pressure fuel pump causing fuel to enter the crankcase and reduce fuel pressure in the direct injection fuel rail. Diagnose this condition using Pinpoint Test HP located in Workshop Manual (WSM), Section 303-04. If no DTCs are stored in the PCM, proceed from Step HP1 to Step HP5 and continue testing. Repair as necessary outside of this article. For claiming, if high-pressure fuel pump replacement is required, use causal part number 9D376 and labor operation code 9543A. If the root cause is identified as anything other than the fuel injection pump, claim the repair outside of this article.
Source components: ENGINE · FUEL/PROPULSION SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2025 F-150, 2022-2025 Expedition/Navigator, 2023-2025 F-Super Duty, 2024-2025 Ranger and 2026 Transit vehicles may exhibit a discharged battery and/or a no crank/no start condition. The vehicle may also exhibit a clicking noise from the trailer module (TRM) while the vehicle is off. This may be due to software in the TRM.<br /><br /> Verify the TRM software part number in the vehicle using Ford diagnosis and repair system (FDRS) to be PC3T-19J297-BF, PC3T-19J297-FF, ML3T-19J297-CD or ML3T-19J297-GD. To confirm a vehicle is equipped with a certain software level, review the software information by hovering over the "Diagnostics" tab in Professional Technician System (PTS) and selecting "Vehicle Software". If one of the listed software part numbers is present, follow the Service Procedure to reprogram the TRM. For vehicles with any other software part number in the TRM, refer to Workshop Manual (WSM), Section 414-01 to continue with normal diagnostics outside of this article. For claiming use causal part 19H332 and labor operation 2006D and 2006D45 of the Service Labor Time Standards (SLTS) Man
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022-2024 Expedition Timberline vehicles may exhibit a condition where the trail turn assist feature is disabled after a few seconds of activation. This may be due to the accessory protocol interface module (APIM) software. Replacement or reprogramming of the APIM will not resolve this condition. Inform customers that engineering is currently working on a solution for this condition and will be released via software updates delivered over-the-air (OTA) expected Q3 2026. Software will update automatically if vehicle connectivity is enabled in the vehicles settings. Schedule a service visit for customers who have disabled vehicle connectivity or who report that they did not receive the update by September 2026. Monitor Professional Technician System (PTS) for additional information.
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2025 F-150, 2022-2025 Expedition/Navigator, 2023-2026 F-Super Duty, 2024-2025 Ranger and 2026 Transit vehicles may exhibit a discharged battery and/or a no crank/no start condition. The vehicle may also exhibit a clicking noise from the trailer module (TRM) while the vehicle is off. This may be due to software in the TRM.<br /><br />Verify the TRM software part number in the vehicle using Ford Diagnosis and Repair System (FDRS) to be PC3T-19J297-BF, PC3T-19J297-FF, ML3T-19J297-CD or ML3T-19J297-GD. To confirm a vehicle is equipped with a certain software level, review the software information by hovering over the "Diagnostics" tab in Professional Technician System (PTS) and selecting "Vehicle Software". If one of the listed software part numbers is present, follow the Service Procedure to reprogram the TRM. For vehicles with any other software part number in the TRM, refer to Workshop Manual (WSM), Section 414-01 to continue with normal diagnostics outside of this article. For claiming, use causal part 19H332 and labor operation 12651D and 12651D4 of the Service Labor Time Standards (SLTS) Man
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022-2024 Expedition/Navigator vehicles equipped with minor feature codes DBCBB or DBCBC may exhibit various driver assistance feature warning messages displayed in the instrument panel cluster (IPC). Additionally, some modules may store diagnostic trouble codes (DTCs) related to invalid data or lost communication. This condition may be due to the software in the image processing module A (IPMA), disrupting network communication. If the IPMA is currently failing to communicate, download and run the "IPMA - Image Processing Module A (IPMA) Recovery" app in the Ford Diagnosis and Repair System (FDRS) scan tool. Select and run the IPMA Recovery Flash Erase option from the apps menu. If the driver assistance warnings and/or symptoms are intermittent, and possibly not failing during the dealership visit, download and run the "IPMA - Image Processing Module A (IPMA) Recovery" app in the FDRS scan tool. Select and run the GWM Ethernet Update option from the apps menu. If IPMA communication had to be restored using the Recovery App, download and run the "IPMA - Image Processing Module (IPMA) Alignm
Source components: ELECTRICAL SYSTEM · FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2025 F-150/Expedition/Navigator vehicles equipped with a 3.5L EcoBoost engine may exhibit diagnostic trouble code (DTC) P0299 stored in the powertrain control module (PCM) and may also exhibit a rattle noise from the turbocharger. This may be due to the wastegate actuator rod being disconnected. Workshop Manual (WSM), Section 303-04 Fuel Charging and Controls > Turbocharger has been added to address this condition to allow servicing of the turbocharger actuator rod. In addition, the wastegate actuator rod and associated retention springs and clips have been released as lower level components to complete the repair without replacing the entire turbocharger actuator assembly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2025 Expedition/Navigator/F-150/F-Super Duty/F-53 Motorhome/F59 Commercial Stripped Chassis/F-650/F-750/Transit vehicles equipped with a 2.7L/3.5L (non hybrid)/6.8L/7.3L engine and 2021-2026 E-Series may exhibit a rattle/scraping noise from the bellhousing area on start-up. Workshop Manual (WSM), Section 303-00 Engine System - General Information > Diagnosis and Testing and 303-06 > Starting System has been updated to address this condition. Additionally, WSM, Section 303-01 > Removal and Installation > Engine to Transmission Spacer Plate has been added to address this condition. Refer to the revised WSM sections for normal diagnosis.
Source components: ENGINE · POWER TRAIN · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022-2024 Expedition/Navigator vehicles equipped with driver assistance features and minor feature codes DBCBB and DBCBC may exhibit driver assistance feature warning messages displayed in the instrument panel cluster (IPC). Additionally, some modules may store invalid data/lost communication related diagnostic trouble codes (DTCs). The image processing module A (IPMA) should not store these DTCs. This condition may be due to the software in the IPMA, causing it to not communicate on the network. Whether the issue is intermittent or the IPMA is currently failing to communicate, download and run the "IPMA - Image Processing Module A (IPMA) Recovery" app in the Ford Diagnosis and Repair System (FDRS) scan tool. If IPMA communication had to be restored using the Recovery App, download and run the "IPMA - Image Processing Module (IPMA) Alignment" app, recheck DTCs and confirm that all warning messages are cleared from the IPC.<br /><br /> If these steps correct the condition, release the vehicle back to the customer. Advise the customers that a permanent repair to prevent recurrence is expected to be
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 25-2104 to update the labor times associated with the Service Procedure. Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: * Inoperative BlueCruise and lane centering * DTC U2018:51 stored in the camera module - rear (CMR) * DTC U0565:86 stored in the image processing module A (IPMA) * DTC U3000:49 is not stored in the CMR This may be due to the software in the CMR.
Source components: ELECTRICAL SYSTEM · FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL · LANE DEPARTURE: ASSIST.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2025 F-150, 2022-2025 Expedition/Navigator, 2023-2025 F-Super Duty, 2024-2025 Ranger and 2026 Transit vehicles may exhibit a discharged battery and/or a no crank/no start condition. The vehicle may also exhibit a clicking noise from the trailer module (TRM) while the vehicle is off. This may be due to software in the TRM.<br /><br />Verify the TRM software part number in the vehicle using Ford diagnosis and repair system (FDRS) to be PC3T-19J297-BF, PC3T-19J297-FF, ML3T-19J297-CD or ML3T-19J297-GD. To confirm a vehicle is equipped with a certain software level, review the software information by hovering over the "Diagnostics" tab in Professional Technician System (PTS) and selecting "Vehicle Software". If one of the listed software part numbers is present, follow the Service Procedure to reprogram the TRM. For vehicles with any other software part number in the TRM, refer to Workshop Manual (WSM), Section 414-01 to continue with normal diagnostics outside of this article. For claiming use causal part 19H332 and labor operation 12651D and 12651D4 of the Service Labor Time Standards (SLTS)
Source components: ELECTRICAL SYSTEM · FUEL/PROPULSION SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2025 various Ford and Lincoln vehicles equipped with blind spot information system (BLIS) may experience an inoperative blind spot monitoring with a "Blind Spot System Fault" message displayed in the instrument panel cluster (IPC). This may also be accompanied by diagnostic trouble codes (DTCs) B118C:11 and/or B118C:15 stored in the driver door module (DDM), and/or B118D:11 and/or B118D:15 stored in the passenger door module (PDM). This may be due to the wiring connector from the mirror to the BLIS module. If diagnostics lead to an internal mirror wiring harness fault, a new lower level BLIS light pigtail is now released for service. It is not necessary to replace the exterior mirror assembly. Use part number SC3Z-14A411-B to resolve the concern.
Source components: ELECTRICAL SYSTEM · LANE DEPARTURE: BLIND SPOT DETECTION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2025 Expedition/Navigator/F-150/F-Super Duty/F-53 Motorhome/F59 Commercial Stripped Chassis/F-650/F-750/Transit vehicles equipped with a 2.7L,3.5L EcoBoost (non-hybrid), 3.5L Cyclone, 6.8L or 7.3L engine, may exhibit a rattle/scraping noise from the bellhousing area on start-up. Workshop Manual (WSM), Section 303-00 Engine System - General Information > Diagnosis and Testing and 303-06 > Starting System has been updated. Additionally, WSM, Section 303-01 > Removal and Installation > Engine to Transmission Spacer Plate has been added to address this condition. Refer to the revised WSM sections for normal diagnosis.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some of the vehicles listed in the Model statement above may exhibit a headliner rattle or sagging condition around the roof opening panel. This may be due to the adhesive separating from the headliner substrate.
Source components: STRUCTURE:BODY · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: - No upshift past second gear - Unable to achieve third gear ratio - Illuminated malfunction indicator lamp (MIL) with DTCs P0757 and P2701 This may be due to a damaged one-way clutch (OWC).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2024-2025 F-150, Expedition/Navigator, Escape/Corsair, Bronco, Explorer, Mustang, Maverick vehicles equipped with a 1.5/2.0/2.3/3.5L EcoBoost engine and built on 01-Oct-2024 and through 31-May-2025 may exhibit an extended crank condition, strong fuel smell in the engine oil, high engine oil level and may have various drivability diagnostic trouble codes (DTCs) stored in the powertrain control module (PCM) with an illuminated malfunction indicator lamp (MIL). This may be due to an internal fuel leak of the fuel injection pump causing fuel to enter the crankcase and reduce fuel pressure in the high pressure fuel rail. Diagnose this condition using Pinpoint Test HP located in the Workshop Manual, Section 303-04A. If no DTCs are stored in the PCM, proceed from Step HP1 to Step HP5 and continue testing. For claiming, if fuel injection pump replacement is required, use causal part number 9D376 and labor operation code 9543A. If the root cause is identified as anything other than the fuel injection pump, claim the repair outside of this article. Note: Components damaged as a result of this failure mode
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various 2021-2025 Ford and Lincoln vehicles equipped with the rear camera on demand feature may exhibit "Please Check Surroundings For Safety" or "Full View Not Available" messages when the rear camera button is pressed and the vehicle is not in reverse. Inform customers this condition is considered normal operation and does not affect vehicle durability because the full rear view camera image can only be shown when the vehicle is in reverse. No additional diagnosis or service is required for this condition.
Source components: UNKNOWN OR OTHER · VISIBILITY/WIPER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2025 Ford and Lincoln vehicles equipped with SYNC4/Digital Experience may exhibit an unsuccessful telematics control unit module (TCU) software update or software activation during a universal serial bus (USB) update. This may be due to the vehicle connectivity setting being disabled.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2023 Explorer, 2022-2023 F-150, and 2023-2024 Expedition/Navigator vehicles equipped with a 2.3L/3.5L EcoBoost engine may exhibit may exhibit an illuminated malfunction indicator lamp (MIL) and/or powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTCs) P25B3, P25B4, P25B5, P25B6, P2ABA, P2ABB, P2ABC, P2AB7, P2AB8, and/or P2AB9 stored in the powertrain control module (PCM). This may be due to a concern with the turbocharger wastegate. To correct the condition, follow the applicable diagnostic pinpoint tests (PPT) steps found in Workshop Manual (WSM), Section 303-04 and repair as necessary.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2024 Edge/Nautilus, 2021-2025 Bronco/Bronco Sport/E-Series/Escape/Corsair/Expedition/Navigator/Explorer/Aviator/F-150/F-Super Duty/Mustang/Ranger, and 2022-2025 Maverick vehicles may require an A/C compressor clutch assembly replacement be performed for various concerns. Workshop Manual (WSM), Section 412-00 Removal and Installation has been updated to eliminate the need to remove and install the A/C compressor to change out the A/C Compressor clutch assembly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2025 Ford/ Lincoln vehicles equipped with SYNC4 may not be able to perform an update to the accessory protocol interface module (APIM). This may be due to the software in the APIM. Ford Engineering has de-activated the ability to update these SYNC4 APIM modules as applicable, and the Ford Diagnosis and Repair System (FDRS) will not present an update for the APIM module. Some existing directed repairs may be impacted, check Professional Technician System (PTS) before attempting any specific technical service bulletin (TSB)/special service message (SSM) and check field service action (FSA) landing pages before attempting any FSA repairs. For any vehicle repairs requiring a software update that includes an APIM update in the programming sequence, if the 5-digit product code for the APIM software is equal to or lower than 23187, do not attempt to update affected modules at this time. To determine the 5-digit product code for the APIM software on the vehicle, while the vehicle center display screen is powered up with ignition in run or accessory, go to Settings > General > About SYNC.
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022-2024 Expedition vehicles equipped with driver assistance features and minor feature codes DBCBB and DBCBC may exhibit driver assistance feature warning messages displayed in the instrument panel cluster (IPC). Additionally, some modules may store invalid data/lost communication related diagnostic trouble codes (DTCs). The image processing module A (IPMA) should not store these DTCs. To confirm a vehicle is built with a certain minor feature code, review the build information by double-clicking the vehicle identification number (VIN) in the upper left corner in the Professional Technician System (PTS). This condition may be due to the software in the IPMA, causing it to not communicate on the network. To restore communication and functionality, download and run the "IPMA - Image Processing Module A (IPMA) Recovery" app in the Ford Diagnosis and Repair System (FDRS) scan tool. Once IPMA communication has been restored, download and run the "IPMA - Image Processing Module (IPMA) Alignment" app, recheck DTCs and confirm that all warning messages are cleared from the IPC.
Source components: ELECTRICAL SYSTEM · LANE DEPARTURE: ASSIST · UNKNOWN OR OTHER · VEHICLE SPEED CONTROL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2025 Expedition/Navigator and 2021-2025 F-150 non-Lightning/non-PowerBoost vehicles may exhibit a rattle/scraping noise from the bellhousing area on start-up. This may be due to the torque converter studs contacting the engine to transmission spacer plate (separator plate). To correct this condition, inspect the engine to transmission spacer plate and torque converter studs for wear/damage. If wear/damage is found, replacement of the torque converter is not necessary. Replace only the engine to transmission spacer plate. Refer to Workshop Manual (WSM) Section 303-01 > Engine to Transmission Spacer Plate for full spacer plate removal and installation. When reinstalling the starter motor, make sure the starter is flush with the engine to transmission spacer plate prior to tightening the studbolts. Failure to do so may result in damaging the newly installed engine to transmission spacer plate.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Continental, 2020-2024 Edge/Nautilus, 2020-2025 Explorer/Aviator/Escape/Corsair/F-150/F-Super Duty/Ranger/Transit/E-Series, 2021-2025 Bronco, and 2022-2025 Maverick vehicles may require an engine cooling system flush to be performed for various concerns. Workshop Manual (WSM), Section 303-03 has been updated to eliminate the need to remove and install the radiator assembly to perform a radiator flush.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2023-2024 Escape/Corsair vehicles equipped with driver assistance features with minor feature code DBCAB for Escape and minor feature code DBCBC for Corsair and 2022-2024 Expedition vehicles equipped with driver assistance features with minor feature codes DBCBB and DBCBC may exhibit driver assistance feature warning messages displayed in the IPC. Additionally, some modules may store invalid data/lost communication related DTCs. The image processing module A (IPMA) should not store these DTCs. To confirm a vehicle is built with a certain minor feature code, review the build information by double-clicking the vehicle identification number (VIN) in the upper left corner in the Professional Technician System (PTS). This condition may be due to the software in the IPMA, causing it to not communicate on the network. To restore communication and functionality, download and run the "IPMA - Image Processing Module A (IPMA) Recovery" app in the Ford Diagnosis and Repair System (FDRS) scan tool. Once IPMA communication has been restored, download and run the "IPMA - Image Processing Module (IPMA) Alignment"
Source components: FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL · FORWARD COLLISION AVOIDANCE: AUTOMATIC EMERGENCY BRAKING · FORWARD COLLISION AVOIDANCE: WARNINGS · LANE DEPARTURE: BLIND SPOT DETECTION · LANE DEPARTURE: WARNING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2024 Expedition/Navigator vehicles equipped with 22 inch wheels, may exhibit an increased level of vibrations which can be felt while driving on a smooth road at speeds at or above 75 mph (120 km/h). Pinpoint Test G located in Workshop Manual (WSM), Section 204-04 has been developed to assist with diagnosis of this condition. When submitting a warranty claim, include all results from the Pinpoint Test.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2025 Ford and Lincoln vehicles may exhibit diagnostic trouble code (DTCs) U2100 and/or U3002 stored in the cruise control module (CCM), side obstacle detection control module LH (SODL), side obstacle detection control module RH (SODR), side obstacle detection control module C (SODCMC) and/or side obstacle detection control module D (SODCMD) after a module replacement.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022-2024 Expedition Timberline vehicles may exhibit a condition where the trail turn assist feature is disabled after a few seconds of activation.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This TSB supersedes 24-2261. Reason for update: update the procedure, parts list and labor operation. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: * Lower than actual fuel level indication on the fuel gauge * Inaccurate DTE displayed in the IPC after adding fuel to the vehicle This may be due to the IPC software and can occur if the vehicle is shut off before placing the gear shift module (GSM) in park (p) and then partially filling the fuel tank.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2023-2024 Escape/Corsair vehicles equipped with driver assistance features with minor feature code DBCAB for Escape and minor feature code DBCBC for Corsair and 2022-2024 Expedition vehicles equipped with driver assistance features with minor feature codes DBCBB and DBCBC may exhibit driver assistance feature warning messages displayed in the IPC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: * General system performance/stability/intermittent system reboot * Intermittent wireless CarPlay or Android Auto function * Phone related concerns with intermittent no audio or static * Navigation/global positioning system (GPS) related concerns through CarPlay and Android Auto * Alexa function consistency and stability * Charge Assist/Public Charging app inoperative (e-Transit only) This may be due to a concern with the software in the accessory protocol interface module (APIM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2024 Model Year F-150, Mustang, Expedition, Navigator, Transit, Super Duty, and 2025 Model Year Explorer vehicles, equipped a 10R80/10R100 Transmission. Transmission Assembly Replacement
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Quality Improvements: - Customer should be able to enable and disable Intelligent power toggle button. -Adresses SYNC reboots and improves the vehicle's conectivity with the user's phone "
Campaign / software reference: 24-OTA SU 10.1.0 Expedition
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2025 Ford and Lincoln vehicles equipped with a 10R60/10R80/10R80 MHT/10R100 transmission may exhibit a whine noise at idle and/or while driving.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 F-150 non-Lightning, 2022-2024 F-150 Lightning/Expedition/Navigator, and 2024 Ranger vehicles may exhibit a "trailer brake module fault" message in the instrument panel cluster (IPC) with diagnostic trouble codes (DTCs) U0137 and/or U0252 stored in the body control module (BCM),
NHTSA source summary · Original PDF not reviewed by Recallfolio
" Some 2023-2024 Escape/Corsair vehicles equipped with driver assistance features with minor feature code DBCAB for Escape and minor feature code DBCBC for Corsair and 2022-2024 Expedition vehicles equipped with driver assistance features with minor feature codes DBCBB and DBCBC may exhibit driver assistance feature warning messages displayed in the IPC"
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Quality improvements include: -Improve battery state of charge drainage issue due to Electronic Control Unit key off load events. -SYNC screen will display correct software update status. -Software update task will be automatically terminated after trigger expiration date"
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles equipped with SYNC4 may exhibit one or more of the following symptoms after all currently available accessory protocol interface module (APIM) software updates have been performed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
In some of the affected vehicles, it is possible the required software required for the Pro Trailer Backup Assist (PTBA) feature was not installed in the vehicle during assembly. A customer with a vehicle that did not receive the required software will be unable to complete the trailer calibration process required to use the PTBA feature. Trailer maneuvering using the steering wheel will be unaffected
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022-2024 Expedition/Navigator vehicles built on or before 09-Oct-2024 may experience a random BLIS indicator illuminated in the exterior mirror with no vehicle or objects near the vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions. While performing a transmission repair on some 2012-2024 Ford and Lincoln vehicles, a transmission seal kit may be on backorder due to supply chain interruptions.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2023-2024 Expedition vehicles equipped with driver assistance features with minor feature code DBCBB and DBCBC may exhibit various driver assistance feature warning messages displayed in the IPC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
An intermittent black screen in the vehicle center display screen with a "Camera Is Unavailable. Please Contact Your Dealership." message in the instrument panel cluster (IPC) when the vehicle is in reverse and DTC B1578:89 stored in the image processing module A (IPMA) may be present on some of the following Ford and Lincoln vehicles: * 2024 F-150/F-Super Duty built on or before 08-Apr-2024 * 2024 Expedition/Navigator built on or before 07-Mar-2024 * 2024 Corsair built on or before 30-May-2024 * 2021-2024 Mustang Mach-E built on or before 20-May-2024
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2024 Ford and Lincoln vehicles may exhibit diagnostic trouble codes (DTCs) U2100 and/or U3002 stored in the cruise control module (CCM), side obstacle detection control module LH (SODL), side obstacle detection control module RH (SODR), side obstacle detection control module C (SODCMC) and/or side obstacle detection control module D (SODCMD) after a module replacement.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2024 Expedition/Navigator vehicles built on or before 19-Dec-2023 may exhibit lower than actual fuel level indication on the fuel gauge or inaccurate DTE displayed in the IPC after adding fuel to the vehicle. This may be due to the IPC software and can occur if the vehicle is shut off before placing the gear shift module (GSM) in park (p) and then partially filling the fuel tank.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 24-2087 to update the vehicle lines, model years affected, action and service procedure. Some 2021-2024 Mustang Mach-E/F-150, 2022-2024 F-150 Lightning/Expedition/Navigator, 2023-2024 Corsair vehicles may exhibit an inoperative BlueCruise and lane centering with DTCs U2018:51 stored in the camera module - rear (CMR) and U0565:86 stored in the image processing module A (IPMA) without DTC U3000:49 stored in the CMR. This may be due to the software level of the CMR. To correct the condition, follow the Service Procedure to reprogram the CMR module using the latest software level of the Ford Diagnosis and Repair System (FDRS).
Source components: FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL · LANE DEPARTURE: ASSIST.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2024 Expedition/Navigator vehicles built on or before 07-Mar-2024 may exhibit a concern where the vehicle is unable to complete the trailer calibration drive for the trailer backup assistance feature. The customer will see all instructional information in the center display screen for the trailer calibration including "Drive Straight Forward To Calibrate", "Drive Left Or Right To Calibrate" and "System Calibrating", but the system will never complete the calibration process. This will prevent customers from using the feature to back up a trailer. This may be due to the software in the image processing module A (IPMA).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2024 F-150 and 2023-2024 Expedition/Navigator vehicles equipped with a 3.5L EcoBoost engine may exhibit a rattle/scraping noise from the bellhousing area on start-up. This may be due to the torque converter studs contacting the engine-to-transmission spacer plate (separator plate). To correct this condition, remove the transmission and flexplate and inspect the engine-to-transmission spacer plate and torque converter studs for wear/damage. If wear/damage is found, replace the engine-to-transmission spacer plate. Refer to Workshop Manual (WSM) Section 303-01 Engine - 3.5L EcoBoost (BM), Removal and Installation, Crankshaft Rear Seal. When reinstalling the starter motor, make sure the starter is flush with the engine-to-transmission spacer plate prior to tightening the studbolts. Failure to do so may result in damaging the newly installed engine-to-transmission spacer plate.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes 24-2028 to update the vehicle symptom. Some 2022-2024 Expedition/Navigator vehicles may exhibit a random "Blind Spot Not Available Sensor Blocked" and/or "Cross Traffic Alert Not Available Sensor Blocked" warning messages in the IPC with no vehicle or objects near the vehicle. This condition may be intermittent, more noticeable in wet conditions. Diagnostic trouble codes B13F3:97 in the side obstacle detection control module - left (SODL) and/or B13F4:97 in the side obstacle detection control module - right (SODR) and/or U0233 and U0232 in the image processing module A (IPMA) may also be present. This may be due to a mud/snow/ice build-up between the radar sensor and the rear bumper cover or damage or corrosion to the radar sensor, connector or harness. To correct the condition, follow the Service Procedure to repair damage and install shields.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some vehicles equipped with SYNC4 may exhibit one or more of the following symptoms after all currently available accessory protocol interface module (APIM) software updates have been performed. - General system performance, stability, and intermittent system reboots. - Intermittent Wireless CarPlay or Android Auto function. - Phone related concerns with intermittent No Audio or Static. - Navigation/global positioning system (GPS) related concerns through CarPlay and Android Auto. - Alexa function consistency and stability. These symptoms may be due to the software in the APIM. Replacing the APIM will not resolve these symptoms for the customer. Before returning the vehicle to the customer, review the procedures within Workshop Manual, Section 415-00 and ensure the latest APIM software is installed. Refer to General Service Bulletin (GSB) 23-7146 for help determining the latest available level of software. IMPORTANT: some module software updates will only display as available on Ford Diagnosis and Repair System (FDRS) after prerequisite modules are updated. This may require the technician to update certain modules multiple times during the service visit, before the latest APIM software is accessible in FDRS. If symptoms continue after latest APIM software has been installed, inform customers that Ford is working on additional software enhancements which are expected to be delivered over-the-air (OTA) by Q4 2024 on F-150, F-150 Lightning, Mustang Mach-E, Mustang, Escape, Corsair, Expedition, Navigator, Bronco, Mustang, and 2023-2024 F-Super Duty. Software will update automatically if vehicle connectivity is enabled in the vehicle's settings. For all other vehicles with SYNC4, schedule a service visit for customers in October 2024, when the updated APIM software is expected to be available to dealers. Monitor OASIS for additional information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022-2024 Expedition/Navigator vehicles may experience a random BLIS indicator illuminated in the exterior mirror with no vehicle or objects near the vehicle. This may be due to the radar signal echoing through the trailer hitch bar. To correct the condition, follow the Service Procedure to block the trailer hitch tube ends.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various vehicles equiped with 10R80/10R80 MHT/10R100/10R140 transmissions may require replacement of the seal kits (7153) when internal repairs are being performed. These kits come with 4 wheel drive (4WD) seals and will no longer include the 2WD seals. When working on a 2WD vehicle, any 2WD seals must be ordered separately. Refer to the parts catalog for the proper 2WD seals required.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2024 Expedition/Navigator vehicles built on or after 14-May-2024 may incorrectly list the keyless entry keypad code card on the loose item checklist. 2024 Expedition/Navigator vehicles built on or after 14-May-2024 do not include keyless entry keypad code cards. Customers are now able to retrieve the vehicle's keyless entry keypad master access code in vehicle by following the instructions in the Owners Manual > Keyless Entry Keypad Master Access Code. This process requires the use of two programmed intelligent access keys.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2019 Explorer and 2018-2024 Transit/F-150/Expedition/Navigator vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0627, P025A, P025B, P00C6, P008A and/or U0109 stored in the powertrain control module (PCM). Diagnosis should include checking for an intermittent or partial disconnect of the harness to the fuel pump control module (FPCM) connector, connector pin push-outs, damaged pins/terminals, or loose/corroded grounds. Confirm FPCM connector (Explorer - C3239, Transit - C433, F-150 - C460/C4336, Expedition/Navigator - C433/C4033) is fully seated and inspect applicable grounds (Explorer G302, Transit - G401, F-150 - G401, Expedition/Navigator - G403/G406) prior to performing guided diagnostics or replacing any components.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2024 Expedition/Navigator vehicles built on or before 19-Dec-2023 may exhibit lower than actual fuel level indication on the fuel gauge or inaccurate DTE displayed in the IPC after adding fuel to the vehicle. This may be due to the IPC software and can occur if the vehicle is shut off before placing the gear shift module (GSM) in park (p) and then partially filling the fuel tank. To correct the condition, perform the IPC module programming using the latest level of the Ford Diagnosis and Repair System (FDRS). For claiming, use causal part 10849 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: ELECTRONIC STABILITY CONTROL (ESC):CONTROL MODULE:SOFTWARE · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Various vehicles have had pinpoint tests, guided routines and the Warranty and Policy Manual recentlyupdated for diagnostics and repairs on SYNC generation 3 and later applications. When performingdiagnostics and repairs on SYNC Gen 3 or later, select the diagnostics tab and search for related symptoms,DTCs and keywords. The search results will be shown in the search results pane. Read and follow allTechnical Service Bulletins (TSB), Special Service Message (SSM)s or General Service Bulletin (GSB) first if abulletin specifically addresses the vehicle concern. If there are no messages, run the appropriate diagnosticpinpoint test found in the Workshop Manual (WSM). Follow the steps in the pinpoint test. Make sure to note thetitle of the guided routine, using the correct one for the vehicle's symptom or diagnostic trouble code (DTC) iscritical. Depending on the outcome of the pinpoint test, a repair validation code (RVC) may be generated eitherin the pinpoint test or Guided Routine. If the vehicle concern still exists after following the pinpoint tests orguided routine, then a manual RVC can be generated using the RVC Assist Form. A manual RVC can only begenerated once the above process has been followed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes 23-2266 to update the vehicle model years affected to include 2024 model year. Some 2022-2024 Expedition/Navigator vehicles may exhibit a random BLIS warning with no vehicle or objects near the vehicle. This condition may be intermittent, more noticeable in wet conditions. Diagnostic trouble codes B13F3:97 in the side obstacle detection control module - left (SODL) and/or B13F4:97 in the side obstacle detection control module - right (SODR) and/or U0233 and U0232 in the image processing module A (IPMA) may also be present. This may be due to a mud/snow/ice build-up between the radar sensor and the rear bumper cover or damage or corrosion to the radar sensor, connector or harness.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022-2024 various Ford/Lincoln vehicles equipped with SYNC 4 may experience concern where customers are receiving an error message when trying to enroll in connected services. This may be due to the gateway module (GWM) software. To correct the concern, download and run the Transport and Factory Mode Deactivation app: under HS1 modules select BCM > Transport and Factory Mode > Download > Run. When the pop-up message appears for Change Vehicle Mode - Transport/Factory/Normal Mode, press OK. This will proceed to the Transport and Factory Mode Deactivation screen, select Unlock Vehicle Connectivity Settings (21 MY + Vehicles). A pop-up message appears noting Vehicle Is Now In Normal Mode, select OK. This will return to the Transport and Factory Mode Deactivation screen, select Exit. A final pop-up notification stating that the application is finished, select OK. For claiming, use causal part 14G490 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
For 2015-2024 Ford and Lincoln vehicles equipped with turbocharged engines and customer concern of an engine oil leak, refer to Workshop Manual (WSM), Section 303-00 for oil leak inspection and testing methods. Ford has evaluated turbochargers replaced for oil leak symptoms and although oil may collect on the external surface of a turbocharger, it is extremely rare for a turbocharger assembly to be the root cause of the oil leak. Careful inspection of the turbocharger oil feed and drain tubes should be performed along with the recommended WSM procedures as needed. Warranty claims for turbocharger replacement going forward will be assessed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2023 F-Super Duty, 2023-2024 Expedition, 2024 Nautilus/F-150 vehicles will exhibit no light emitting diode (LED) confirmation from the key fob indicating that the vehicle has remote started (or not remote started). Factory key fobs with remote start no longer contain a LED feedback indicator. Do not replace the key fob for this condition. This is a normal operating characteristic and no service action is necessary.
Source components: ELECTRICAL SYSTEM:IGNITION:ANTI-THEFT:IMMOBILIZER/PROXIMITY:KEY/SENDER · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
During service and repair requiring removal and replacement of a crankshaft bolt and/or crankshaft damper, achieving proper torque of the crankshaft pulley bolt is critical. Incorrect torque may allow the bolt to loosen resulting in the timing gear breaking and engine damage. Replacement of the bolt is critical to the repair and accurately following the installation procedure in the Workshop Manual (WSM) Section, 303-01 is extremely important. The bolt torque procedure can be found in the crankshaft front seal removal and installation procedure or in the engine assembly procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 F-150 and 2023-2024 Expedition/Navigator vehicles equipped with a 3.5L EcoBoost engine may exhibit a rattle/scraping noise from the bellhousing area on start-up. This may be due to the torque converter studs contacting the engine-to-transmission spacer plate (separator plate). To correct this condition, remove the transmission and flexplate and inspect the engine-to-transmission spacer plate and torque converter studs for wear/damage. If wear/damage is found, replace engine-to-transmission spacer plate. Refer to Workshop Manual (WSM) Section 303-01 Engine - 3.5L EcoBoost (BM), Removal and Installation, Crankshaft Rear Seal. When reinstalling the starter motor, be sure the starter is flush with the engine-to-transmission spacer plate prior to tightening the studbolts. Failure to do so may result in damaging newly installed engine-to-transmission spacer plate.
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2022-2024 Explorer/Aviator vehicles built on or after 28-May-2022, 2022-2024 Expedition/Navigator vehicles built on or after 08-Jun-2022, 2022-2024 Escape vehicles built on or after 01-Jun-2022 and 2022 Corsair vehicles built on or after 01-Jun-2022 are no longer equipped with a hands free liftgate system. The vehicle is not misbuilt. The addition of any parts is not a warrantable repair. Do not submit a claim for this condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022-2024 Expedition/Navigator vehicles equipped with a 1 speed transfer case may exhibit a concern where the four-wheel drive (4WD) setting reverts to 2H (two-wheel drive) after a key cycle. This may be due to the transfer case control module (TCCM) software. To correct the condition, reprogram the TCCM using the latest version of the Ford Diagnosis and Repair System (FDRS). For claiming, use causal part 7E453 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022-2024 Expedition vehicles equipped with an analog camera and a 12 inch center display screen may exhibit a rear camera image that the customer describes as grainy, fuzzy, or pixelated. This may be due to the interaction between the analog camera and the high definition digital center display screen. To confirm a vehicle is built with an analog camera and a 12 inch center display screen, verify the minor feature codes J3KAR (REAR VIEW CAMERA - LEVEL 2) and HJGAX (MULTI FUNCTION DISPLAY - 12 inch) by reviewing the build information by double-clicking the vehicle identification number (VIN) in the upper left corner in the Professional Technician System (PTS). This is an operating characteristic of the vehicle. Do not attempt any repairs for this condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022-2024 Expedition/Navigator vehicles may exhibit a random BLIS warning with no vehicle or objects near the vehicle. This may be due to a mud/snow/ice build-up between the radar sensor and the rear bumper cover or damage or corrosion to the radar sensor, connector or harness