2018 Ford EXPEDITION Manufacturer communications & TSBs.Page 2
Original record summaries, dates and identifiers for this model-year. Records 101–165 of 165, ordered newest first. Dated records on this page: Jun 19, 2018–Jul 15, 2021.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Jul 15, 2021Service Bulletin/Repair Instructions
21B10-S2
NHTSA communication ID: 10199480
NHTSA source summary · Original PDF not reviewed by Recallfolio
In some of the affected vehicles, an undesirable noise may develop from the cam phasers in the 3.5L GTDI engine. This noise might occur as a rattle when starting the engine after the vehicle was turned off for an extended period of time, or as a knocking noise when the engine is idling after it is warmed up. A cam phaser that has developed an undesirable noise does not affect the vehicle safety, performance, or emissions.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2021 Edge, 2016-2018 MKX, 2019-2021 Nautilus, 2018-2021 Expedition/Navigator, and 2020-2021 Escape/Corsair/Explorer/Aviator vehicles may exhibit an inoperative power liftgate. This may be due to the rear gate trunk module (RGTM) software. To correct the condition, reprogram the RGTM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 14B291 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016 MKS, 2016-2017 Navigator, 2016-2018 F-150/Focus/C-MAX/Edge/Fiesta/MKX/Transit Connect/Mustang, 2017-2018 Continental/Fusion/MKZ, 2017-2019 Explorer, 2016-2019 Escape/MKC/Flex/MKT/Taurus/Transit/Expedition/F-Super Duty, and 2018-2019 EcoSport vehicles equipped with SYNC 3 may experience various SYNC performance related concerns.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2021 Ford and Lincoln vehicle owners may experience a condition of missing Authorization, Command and Control, Battery Charging Details or Phone-as-a-Key setup buttons/selections in their FordPass or LincolnWay App. This condition is due to an error within the FordPass or LincolnWay App and not due to a concern on the vehicle. Verify that the customers FordPass or LincolnWay App is at the latest version. Replacement or reprogramming of the telematics control unit (TCU)/gateway module (GWM)/remote function actuator (RFA) will not resolve this condition. If the condition persists, Utilize the FordPass Guides or Lincoln Way Concierge teams.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2020 Ford and Lincoln vehicles may exhibit inoperative remote features via the Ford Pass/Lincoln Way mobile app, incomplete user authorization, no modem electronic serial number (ESN) displayed or DTCs U2100 and/or B156D in the telematics control unit (TCU). These symptoms may persist even after performing a TCU software update and/or replacement. To correct this condition, start a new session with the latest version of the appropriate diagnostic scan tool and perform a PMI on the TCU. If issues persist, open a hotline assistance request and include the IDS version (if applicable) used to perform the PMI and the Authorization Status PID value in the TCU datalogger. For claiming use causal part 14G229 and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2021 Ford and Lincoln vehicles may not be able to perform remote commands via the FordPass/LincolnWay App due to an erroneous deep sleep message. If the vehicle has been driven within 14 days and the battery state of charge is above 9.5 volts when the deep sleep message set, this is an erroneous message. Starting and running the vehicle will clear the message and allow the remote commands to function again. Inform customers that engineering is currently working on a solution for this condition that will be released via an over the air (OTA) update that is expected in June 2021. Replacement or reprogramming of the telematics control unit (TCU)/gateway module (GWM) will not resolve this condition. Monitor OASIS for additional information and schedule service appointments for customers once the repair becomes available.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2021 vehicles supported by FDRS may not list a software update for a module under the SW Updates tab although an SSM or TSB is published for a software update. This may be due to the module already being at the latest software level. A later software level may have been programmed at the assembly plant, during a previous dealer visit or by an over the air (OTA) update for vehicles that have automatic updates enabled in the SYNC system settings. To review a vehicle's OTA update history, visit the Connected Vehicle > OTA Dashboard tab in OASIS. Information about the OTA Dashboard can be found on FMCDealer.com when performing a search on OTA History Job Aid.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2020 F-150 2018-2020 Expedition/Navigator vehicles built on or before 31-Oct-2019 and equipped with a 3.5L EcoBoost engine may exhibit a ticking/tapping or rattle type noise from the top front cover area of the engine on initial start-up after a cold soak of 6 hours or more that may last for 2-5 seconds. This may be due to a worn variable cam timing (VCT) unit. To correct the condition, follow the Service Procedure steps to replace the VCT units.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2021 Expedition/Navigator vehicles equipped with electronic limited slip differential (ELSD) rear axle may exhibit an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble code (DTC) P0932:17. Check the condition of the wiring harness and connections at the ELSD and the differential control module rear (DCMR). If no problems are found, clear the DTC and test drive. If the condition returns, refer to Workshop Manual (WSM), Section 308-07A.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2018 Model Year Expedition and Navigator Vehicles Equipped With R-1234yf Refrigerant Special R-1234yf Refrigerant Service Information Vehicles not previously repaired with certain build dates, and that remain in program 18N01, can now request loaner equipment for vehicles even if they are outside of New Vehicle Limited Warranty. Vehicles not previously repaired with certain build dates, are now open in Customer Satisfaction Program 20N08 with updated labor operation codes, part ordering information, and repair instructions. Updated Technical Instructions: Dealers are to obtain the equipment from Ford Motor Company necessary to evacuate the A/C system.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2019 F-150/F-Super Duty/Expedition/Navigator and 2020 Explorer/Aviator vehicles may exhibit a 'Trailer Connected' or 'Trailer Disconnected' message in the vehicle's message center with no trailer attached to the vehicle. To address this condition, reprogram the trailer module (TRM) using the appropriate Ford diagnostic scan tool. For claiming use causal part 19H332 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
For 2018-2021 EcoSport/Expedition/Navigator, 2019-2021 Ranger/Transit Connect, 2020-2021 Escape/Explorer/SuperDuty/Transit/Aviator/Corsair, 2021 Bronco Sport/F-150/Mustang/Mach-E the Workshop Manual (WSM) diagnostics may direct to replace a module on vehicles that use Ford Diagnosis and Repair System (FDRS). First, an FDRS session must be created on the vehicle prior to removing the faulted module. Once the session is started, run the Programmable Module Installation and replace the module only when instructed by FDRS. Installing a new module prior to starting a scan tool session may result in incomplete module configuration with DTCs U2100, U2101 and/or U2200. Once a session has been started, continue to follow normal WSM procedures to repair the vehicle.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2018 Model Year Expedition and Navigator Vehicles Equipped With R-1234yf Refrigerant Special R-1234yf Refrigerant Service Information This program provides special service instructions, loaner equipment, and rental assistance to expedite the repair of affected vehicles equipped with R-1234yf Air Conditioner (A/C) refrigerant, which may be contaminated
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2021 F-150, Expedition, Navigator, Transit, Aviator and Explorer vehicles may exhibit an illuminated MIL with DTC P025A And/Or DTC U0109 stored in the powertrain control module (PCM). This may be due to an intermittent or partial disconnect of the harness to the fuel pump control module (FPCM) connector, connector pin push-outs or loose/corroded grounds. Inspect FPCM connector, applicable grounds(F-150- G401, Expedition/Navigator- G403, Transit- G401, 2018-2019 Explorer G302, 2020-2021 Explorer/Aviator- G407) and confirm FPCM connector (F-150- C4336, Expedition/Navigator- C433, Transit- C433, 2018-2019 Explorer C3239, 2020-2021 Explorer/Aviator- C4033) is fully seated prior to performing PC/ED diagnostics or replacing any components.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2020 Ford and Lincoln vehicles equipped with TCU and WiFi Hotspot, May display Vehicle Hotspot feature not enabled on this vehicle when attempting to enter the Hotspot menu. When using the FordPass/Lincoln Way application, the customer may receive a message saying Wi-Fi has been disabled from this vehicle. Check the vehicle specifications or vehicle build information for the mfal code on the PTS website (Detailed Vehicle Specifications). If mfal = WAFAC or WAFAB do not replace the TCU, engineering is currently investigating this condition. Inform customers Ford is developing a software fix that is expected in early March. In the interim, let the customer know they can continue to drive the vehicle and schedule a follow-up appointment with the customer for early March. Monitor OASIS for updates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 19-2220 to update the Part List, Service Procedure and production fix date. Some 2018-2019 Expedition/Navigator vehicles built on or before 7-Jun-2020 may exhibit a difficulty unlatching or latching doors and/or locking or unlocking doors. This may be due to water intrusion into the door handle cables. To correct the condition, follow the Service Procedure steps to replace the mini latch module assembly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2020 F-150 and 2018-2020 Expedition/Navigator vehicles equipped with a 3.5L/2.7L EcoBoost engine and four-wheel drive (4WD) may exhibit an intermittent grinding type noise while driving in two-wheel drive (2WD), most commonly on acceleration. This noise could appear to be turbocharger related. After engineering analysis of returned turbochargers that have been replaced for this condition, no concerns were identified with the turbochargers. The grinding type noise may be related to the 4WD system integrated wheel ends (IWE). To aid in diagnosis, shift the vehicle to 4WD and attempt to verify the condition. If the grinding noise no longer occurs with the vehicle in 4WD a IWE vacuum system and/or mechanical fault may be present.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2020 Ford and Lincoln vehicles may exhibit inoperative remote features via the Ford Pass/Lincoln Way mobile app, incomplete user authorization, no modem electronic serial number (ESN) displayed or DTCs U2100 and/or B156D in the telematics control unit (TCU). These symptoms may persist even after performing a TCU software update and/or replacement. To correct this condition, start a new session with the latest version of the appropriate diagnostic scan tool and perform a PMI on the TCU. If issues persist, open a hotline assistance request and include the IDS version (if applicable) used to perform the PMI and the Authorization Status PID value in the TCU datalogger. For claiming use causal part 14H092 and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: ELECTRICAL SYSTEM:SOFTWARE · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018 EcoSport/Expedition/Explorer vehicles equipped with a telematics control unit (TCU) module may exhibit an inoperative remote start with a Vehicle Failed To Start message when using the Ford Pass mobile application. This message may be observed even if the vehicle has been driven immediately prior to the remote start request. Other functions such as remote lock and unlock from the Ford Pass mobile application will work as expected. Engineering is currently investigating this condition. Inform customers Ford is developing a software fix that is expected in early January. In the interim, let the customer know they can continue to drive the vehicle and schedule a follow-up appointment with the customer for early January. Once the update becomes available, contact the customer and confirm the service appointment is going forward. Monitor OASIS for updates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2020 Ford and Lincoln vehicles equipped with TCU and WiFi Hotspot, May display Vehicle Hotspot feature not enabled on this vehicle when attempting to enter the Hotspot menu. When using the FordPass/Lincoln Way application, the customer may receive a message saying Wi-Fi has been disabled from this vehicle. Check the vehicle specifications or vehicle build information for the mfal code. If mfal = WAFAC or WAFAB do not replace the TCU, engineering is currently investigating this condition. Inform customers Ford is developing a software fix that is expected in early January. In the interim, let the customer know they can continue to drive the vehicle and schedule a follow-up appointment with the customer for early January. Once the update becomes available, contact the customer and confirm the service appointment is going forward. Monitor OASIS for updates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
The service part long block for 2017-2018 F-150 vehicles equipped with a 3.5L EcoBoost engine built at Kansas City Assembly Plant on or before 23-Feb-2018 or Dearborn Truck Plant on or before 26-Feb-2018 and 2018 Expedition/Navigator vehicles built on or before 19-Mar-2018 has been changed to a one piece oil pan design. To make sure there is proper fitment of the new long block with the one piece oil pan, replacement of the transmission cooler coolant lines and an engine harness modification will be necessary. To correctly install, follow the Service Procedure steps to complete the repair.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT · POWER TRAIN:AUTOMATIC TRANSMISSION:COOLING UNIT AND LINES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2003-2020 Expedition/Navigator and 2006-2020 F-150 vehicles equipped with TOD transfer cases may exhibit grinding/clicking/ratcheting noise from the front wheel area. This may be due to partial engagement of the integrated wheel ends (IWE). To correct this condition, follow the Service Procedure steps to remove and cap the vacuum supply line.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · WHEELS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2009-2020 Ford and Lincoln vehicles equipped with turbochargers may exhibit an oil leak from the turbocharger oil supply or return tubes, O-rings or 6.7L pedestal gasket. Although oil may collect on the turbocharger, it is very rare for a turbocharger to leak oil. To isolate the source of the leak, refer to Workshop Manual (WSM), Section 303-00 General Information > Diagnosis and Testing > Engine > Engine Oil Leaks - Fluorescent Oil Additive Method procedure. When an oil leak is present at a turbocharger oil supply or drain tube, remove the affected oil tube and inspect for damage, and replace the O-ring seals, pedestal gasket or oil tube as required. Refer to WSM, Section 303-04. For claiming, use the affected oil tube or pedestal gasket as the causal part and applicable labor operations in Sections 6 and 9 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2020 F-150 2018-2020 Expedition/Navigator vehicles built on or before 31-Oct-2019 and equipped with a 3.5L EcoBoost engine may exhibit a ticking/tapping or rattle type noise from the top front cover area of the engine on initial start-up after a cold soak of 6 hours or more that may last for 2-5 seconds. This may be due to a worn variable cam timing (VCT) unit. To correct the condition, follow the Service Procedure steps to replace the VCT units and update the powertrain control module (PCM) calibration with revised VCT parameters.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2020 F-150 except Raptor, 2017-2020 F-Super Duty, 2018-2020 Expedition vehicles equipped with a front camera washer may exhibit a washer fluid leak at the front camera washer jet when not in use. This may be due to the rubber seal internal to the jet. To correct the condition, follow the Service Procedure to replace the washer jet.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app , incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2020 Expedition/Navigator two-wheel drive (2WD) vehicles may exhibit a clunk noise from the driveshaft area when shifting from REVERSE to DRIVE or DRIVE to REVERSE and/or during coast down. This condition may be caused by a slip/stick condition at the transmission output flange/anti-ting ring interface. To correct the condition, follow the Service Procedure to apply a light coating of grease to the anti-ting washer and output shaft splines.
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016 MKS, 2016-2017 Navigator, 2016-2018 F150/Focus/CMAX/Edge/Fiesta/MKX/ Transit Connect/Mustang, 2017-2018 Continental/Fusion/MKZ, 2017-2019 Explorer, 2016-2019 Escape/MKC/Flex/MKT/Taurus/Transit/Expedition/F-Super Duty, and 2018-2019 EcoSport vehicles equipped with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2019 Explorer/Expedition/F-150/F-Super Duty/Taurus vehicles equipped with a forward collision warning head up display (HUD) may exhibit various warning indicators caused by a possible intermittent lack of HS2-CAN (HS-CAN for Taurus) network communication. If the concern cannot be duplicated, place the vehicle in direct sunlight for 15 to 30 minutes to increase the temperature of the HUD and retest. If the concern is present, disconnect the HUD and check for proper network communication. If proper network communication is achieved, then HUD module replacement is likely needed. If disconnecting the HUD does not re-establish communication, the HUD is not at fault, refer to Workshop Manual (WSM), Section 418-00 for diagnostics.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 19-2026 to update the vehicle model years affected. Some 2000 and newer Ford/Lincoln/Mercury vehicles equipped with aluminum body panels may exhibit corrosion concerns appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2019 Explorer/Expedition/F-150/F-Super Duty/Taurus vehicles equipped with a forward collision warning head up display (HUD) may exhibit various warning indicators caused by a possible intermittent lack of HS2-CAN network communication. If the concern cannot be duplicated, place the vehicle in direct sunlight for 15 to 30 minutes to increase the temperature of the HUD and retest. If the concern is present, disconnect the HUD and check for proper HS2-CAN network communication. If proper HS2-CAN network communication is achieved, then HUD module replacement is likely needed. If disconnecting the HUD does not re-establish communication, the HUD is not at fault, refer to Workshop Manual (WSM), Section 418-00, PPT AL for diagnostics.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2020 Ford and Lincoln vehicles equipped with a SYNC 3 Touchscreen may experience the volume control unresponsive from the Front Control Interface Module (FCIM) and steering volume controls when using Apple Car Play. When the Apple device is removed, volume control is restored. This is due to a concern with the Waze Navigation App software and Apple iOS version. To correct the condition, update the Waze App software and iOS to the latest version available and reboot the customer's Apple device. Perform an ignition cycle and reconnect the Apple device via USB. Open Apple Car Play and confirm volume control is restored. Installing/Updating third party software/applications is not warrantable.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2019 Expedition/Navigator vehicles built on or before 8-Apr-2019 equipped with a 3.5L EcoBoost engine may exhibit a ticking/tapping or rattle type noise from the top front cover area of the engine on initial start-up after a cold soak of 6 hours or more that may last for 2-5 seconds. This may be due to a worn variable cam timing (VCT) unit. To correct the condition, follow the Service Procedure steps to replace the VCT units and update the powertrain control module (PCM) calibration with revised VCT parameters.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT ADAPTIVE/MOBILITY · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 20-2028 to update the description of Labor Operation D. Some 2013-2018 F-150/Expedition/Navigator vehicles equipped with 4-wheel drive (4WD) may exhibit an intermittent grinding noise while driving in 2-wheel drive (2WD) mode most commonly on acceleration. This may be due to a loss of vacuum to the integrated wheel end (IWE) actuators and/or wear of the IWE components. To correct the condition, follow the Service Procedure steps to reprogram the transfer case control module (TCCM) and replace any worn vacuum and/or IWE components.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2012-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit an inoperative remote start with a 'Vehicle Failed To Start' message when using MyFord Mobile/Ford Pass/Lincoln Way mobile applications. The cellular cloud systems will only allow two remote start requests from the MyFord Mobile/Ford Pass/Lincoln Way apps without a vehicle drive event occurring. If a third remote start request is received, a Vehicle Failed To Start message will be displayed quickly in the mobile app. Once the vehicle is driven, the remote start counter is reset and will allow remote start commands to be sent from the mobile app. If the remote start system is not functioning using the key fob, refer to Workshop Manual (WSM) Section 303-06 for further diagnosis.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2018 C-Max, 2013-2020 Escape/Fusion/MKZ, 2015-2018 Focus,2015-2019 MKC, 2015-2020 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2020 F-Super Duty, 2018-2020 EcoSport/Expedition, 2019-2020 Ranger/Nautilus vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
Source components: SEATS · STRUCTURE:FRAME AND MEMBERS:UNDERBODY SHIELDS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2020 F-150/Expedition/Navigator/F-Super Duty vehicles built on 31-Aug-2018 and through 02-Feb-2020 may exhibit a water leak on the right front floor during and/or after the air conditioning (A/C) is used. This may be due to condensation from the evaporator drain tube entering the vehicle through the drain tube seal. To correct the condition, follow the Service Procedure steps to install an elbow on the evaporator drain tube to direct the condensation away from the seal.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 19-2232 to update the vehicles affected. Some 2017-2019 F-150 and 2018-2019 Expedition vehicles built on or before 1-Apr-2019 and equipped with a 3.5L EcoBoost engine may exhibit excessive oil consumption with no visible oil leaks with or without diagnostic trouble code (DTC) P0365 and/or P0369. This may be due to a concern with the positive crankcase ventilation (PCV) system. To correct the condition, follow the Service Procedure steps to verify the condition and replace the valve covers.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2020 Model year vehicles equipped with 3.3L, 3.5L EcoBoost, or 5.0L engines may exhibit stalling, lack of power, low fuel rail pressure and/or DTCs P0087 or P008A after a repair was made that required the removal of the fuel line that connects the high-pressure fuel pump to the port injection rail, such as injector replacements or base engine repairs. This line must be installed in the correct orientation as it has an internal one-way check valve. To determine if the fuel line has been installed improperly, look at the position of the Oetiker clamp (stainless band clamped around the black fuel line). The clamp holds the one-way check valve in place and should be located closest to the end connected to the port injection rail. If the clamp is not closest to the port injection rail, remove and reinstall the line in the proper orientation.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2018 F-150/Raptor, 2018 Expedition/Mustang/Navigator vehicles equipped with a 10R80 automatic transmission and built on or before 20-Nov-2017 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P0741 and P1744 in the powertrain control module (PCM) or transmission control module (TCM). This may be due to a sticking torque converter clutch (TCC) valve in the main control valve body assembly. To correct the condition, follow the Service Procedure to replace the main control valve body.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2018 F-150 vehicles equipped with a 3.5L EcoBoost engine built at Kansas City Assembly Plant on or before 23-Feb-2018 or Dearborn Truck Plant on or before 26-Feb-2018 and Expedition/Navigator vehicles built on or before 19-Mar-2018 may exhibit an oil leak from the oil pan RTV seal. This may be due to a lack of RTV adhesion. This article includes detailed steps to achieve proper RTV adhesion. To correct the condition, follow the Service Procedure steps to replace the oil pan.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2018 F-150/Expedition/Navigator vehicles equipped with 4-wheel drive (4WD) may exhibit an intermittent grinding noise while driving in 2-wheel drive (2WD) mode most commonly on acceleration. This may be due to a loss of vacuum to the integrated wheel end (IWE) actuators and/or wear of the IWE components. To correct the condition, follow the Service Procedure steps to reprogram the transfer case control module (TCCM) and replace any worn vacuum and/or IWE components.
Source components: EQUIPMENT · SERVICE BRAKES, HYDRAULIC:POWER ASSIST:VACUUM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2018 F-150 vehicles equipped with a 3.5L EcoBoost engine built at Kansas City Assembly Plant on or before 23-Feb-2018 or Dearborn Truck Plant on or before 26-Feb-2018 and Expedition/Navigator vehicles built on or before 19-Mar-2018 may exhibit an oil leak from the oil pan RTV seal. This may be due to a lack of RTV adhesion. This article includes detailed steps to achieve proper RTV adhesion. To correct the condition, follow the Service Procedure steps to replace the oil pan.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2019 F-150, 2017-2019 F-Super Duty, 2018-2019 Expedition/Navigator vehicles may exhibit a rattle and/or squeak noise from the vista roof opening panel while driving with the roof opening panel closed. This may be due to dirt and/or debris build up between the vista roof opening panel seal and the body. To correct the condition, follow the Service Procedure steps to clean and lubricate the vista roof opening panel seal.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2020 F-150/Expedition/Navigator/F-Super Duty vehicles may exhibit a water leak on the right front floor during or after the air conditioning (A/C) is used. This may be due to condensation from the evaporator drain tube entering the vehicle through the drain tube seal. To correct the condition, follow the Service Procedure steps to install an elbow on the evaporator drain tube to direct condensation away from the seal.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2018 F-150s built on or before 10-Jul-2018 and 2018-2019 Expedition and Navigator built on or before 8-Apr-2019 with 3.5L EcoBoost may exhibit tick, tap, or rattle type noises from top of engine front cover for 2-5 seconds after a cold start. A TSB is expected to be published late 4th quarter 2019. In the interim, replace all 4 VCT units and update the PCM calibration. Do not replace other cam drive related components unless inspection identifies a concern. Refer to the Workshop Manual (WSM), Section 303-01. Claim labor replace VCTs using published labor operations and PCM programming using M-time. Part availability is currently limited. Dealers should order parts only when required to complete a repair. Once the parts are ordered, the vehicle may be returned to the customer to drive. This condition does not affect long term durability or performance.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2018 F-150 vehicles built on or before 10-Jul-2018 and 2018-2019 Expedition/Navigator vehicles built on or before 8-Apr-2019 equipped with a 3.5L EcoBoost engine may exhibit a ticking, tapping, or rattle type noise from the top front cover area of the engine that last 2-5 seconds on initial start-up after a cold soak. This may be due to a worn variable cam timing (VCT) unit. A TSB is expected to be published 4th quarter of 2019. In the interim, replace all 4 VCT units and update the powertrain control module (PCM) calibration. Do not replace timing chains, tensioners, guides or other timing related components unless inspection clearly identifies a concern. Refer to the Workshop Manual (WSM), Section 303-01. Claim the labor required to replace VCTs using published labor operations and PCM programming using M-time. Monitor OASIS for updates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2019 vehicles may experience a no crank concern due to a security access key table error. When attempting to program keys or perform a parameter reset, the procedure may fail and the appropriate Ford diagnostic scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the body control module (BCM) is internally damaged and requires replacement. The BCM should only be replaced for this condition when the 232 key table error message is present. If the 232 key table error is not present, follow normal diagnostics for the no crank condition. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2019 F-150 and 2018-2019 Expedition/Navigator vehicles built on or before 1-Apr-2019 and equipped with a 3.5L EcoBoost engine may exhibit excessive oil consumption with no visible oil leaks with or without diagnostic trouble code (DTC) P0365 and/or P0369. This may be due to a concern with the positive crankcase ventilation (PCV) system. To correct the condition, follow the Service Procedure steps to verify the condition and replace the valve covers.
Source components: ENGINE AND ENGINE COOLING · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 F-150/Expedition/Navigator vehicles equipped with a 3.5L/2.7L EcoBoost engine and four-wheel drive (4WD) may exhibit an intermittent grinding type noise while driving in two-wheel drive (2WD), most commonly on acceleration. This noise could appear to be turbocharger related. After engineering analysis of returned turbochargers that have been replaced for this condition, no concerns were identified with the turbochargers. The grinding type noise may be related to the 4WD system integrated wheel ends (IWE). To aid in diagnosis, shift the vehicle to 4WD and attempt to verify the condition. If the grinding noise no longer occurs with the vehicle in 4WD a IWE vacuum system and/or mechanical fault may be present.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2018 F-150 and 2018-2019 Expedition/Navigator vehicles equipped with a 3.5L EcoBoost engine, where the variable cam timing (VCT) unit or long block assembly requires replacement for any reason, the PCM calibration must also be updated during the repair using the latest version of the appropriate Ford scan tool. Claim the labor required to complete PCM programming using M time. Monitor Oasis for updates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2019 F-150 and 2018-2019 Expedition/Navigator vehicles equipped with a 3.5L EcoBoost engine built on or before 1-Apr-2019 may exhibit excessive oil consumption with or without diagnostic trouble code (DTC) P0365 and/or P0369. If there are no visible external oil leaks, replace both valve covers. Refer to Workshop Manual, Section 303-01. For claiming, use causal part 6582 and applicable labor operations in Section 6 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2019 F-150 vehicles equipped with a 3.5L EcoBoost or 2.7L EcoBoost engine and some 2018-2019 Expedition and Navigator vehicles equipped with a 3.5L EcoBoost engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P04F0 and/or P144C stored in the powertrain control module (PCM). This may be due to loose or partially connected evaporative emissions (EVAP) vapor lines. Before completing the Powertrain Control/Emissions Diagnosis (PC/ED) Manual pinpoint test (PPT) HX follow the Service Procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Common portion of a presentation provided to mutiple OEM customers concerning a potential issue and investigation involving a seat adjustment recliner mechanism.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2019 F-150, 2018-2019 Expedition/Navigator/Mustang, 2019 Ranger vehicles equipped with a 10R80 transmission may exhibit a whine noise. This may occur at idle and while driving coming from the bell housing and front pan area of the transmission. The whine noise may become louder when at operating temperature and increases with higher engine RPM in the PARK position. A small amount of whine noise is considered to be characteristic of the 10R80 transmission due to the offset gear drivetrain in the front support and has no effect on durability.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2018 Expedition/Navigator, 2018-2019 F-Super Duty and 2019 E-Series/F-650/F-750 vehicles built on or after 9-Jul-2018 and 2019 F-150/Transit vehicles built on or after 2-Jan-2019 are filled with the new Motorcraft Yellow Antifreeze/Coolant. When servicing the cooling system(s) on these vehicles, use Motorcraft Yellow Antifreeze/Coolant VC-13-G (CVC-13-G for Canada). Do not mix different colors or types of coolant. NOTE: The Motorcraft Yellow Antifreeze/Coolant may appear green in color due to the florescent dye used.
Source components: ENGINE AND ENGINE COOLING · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2018 Expedition/Navigator vehicles may experience a noisy, soft, spongy and/or bouncy ride quality while driving. This may be the result of a shock absorber that is leaking fluid. To assist with the investigation please use the Report a Vehicle Concern link at the bottom of the OASIS tab on the PTS website. Include detail on which shock absorber(s) appear to be leaking and if the vehicle is in for a repeat repair for this concern. To further aid in this investigation, please attach a photo of the shock absorber date code label from the leaking shock(s). This label will have the word CAUTION at the top and may appear silver in color with a colored stripe on one side. Engineering is currently investigating this concern.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2018 F-150 and 2018 Expedition/Navigator vehicles equipped with a 3.5L EcoBoost and built on or before 13-Jul-2018 may exhibit diagnostic trouble code (DTC) P0365 and/or P0369 with excessive oil consumption. If there are no visible external oil leaks, replace both engine valve covers. Refer to Workshop Manual, Section 303-01. For claiming, use causal part 6582 and applicable labor operations in Section 6 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2018 Model Year Expedition and Navigator Vehicles Equipped With R-1234yf Refrigerant - Special R-1234yf Refrigerant Service Information. Certain 2015-2018 Model Year F-150 and 2017-2018 Model Year F-250-F-550 - Vehicles - Door Latch Freezing Concerns
NHTSA source summary · Original PDF not reviewed by Recallfolio
2018 Expedition/Navigator, 2018-2019 F-Super Duty, 2019 E-Series and F-650/F-750 vehicles built on or after 9-Jul-2018 are filled with the new Motorcraft Yellow Antifreeze/Coolant. When servicing the cooling system(s) on these vehicles, use Motorcraft Yellow Antifreeze/Coolant VC-13-G (CVC-13-G for Canada). Do not mix different colors or types of coolant, including mixing Motorcraft Yellow with similarly colored Motorcraft Gold. Monitor OASIS for updates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 F-150, 2017-2018 F-Super Duty, 2018 Expedition/Navigator vehicles equipped with a vista roof opening panel may exhibit a concern with the glass panel brackets. The brackets may crack and/or break apart resulting in symptoms that include but are not limited to binding/sticking, glass stuck open or closed, noisy operation including chatter, rattling, or grinding. The roof opening panel glass brackets are available for service as a kit (FL3Z-1651070-C). Refer to Workshop Manual (WSM), Section 501-17 for diagnosis and repair procedures. Make sure the track is free of debris prior to assembly. For claiming, use causal part 1651070 and applicable labor operations in Section 12 of the Service Labor Time Standards (SLTS) Manual. Labor operations for removal and installation of the glass and glass brackets (guides) apply.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2018 F-150 and 2017-2018 Expedition/Navigator vehicles may exhibit an intermittent grinding noise coming from the right or left IWE area in 2WD mode. This may be caused by an intermittent leak in the check valve. Before completing any normal diagnosis suspect that the check valve is the root cause of the issue. If the check valve has been ruled out as the root cause for the issue refer to Work Shop Manual 308-07 and follow normal diagnosis.