2022 Ford ESCAPE Manufacturer communications & TSBs.Page 2
Original record summaries, dates and identifiers for this model-year. Records 101–154 of 154, ordered newest first. Dated records on this page: Dec 16, 2021–Apr 25, 2023.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Apr 25, 2023Service Bulletin/Repair Instructions
SSM 51575
NHTSA communication ID: 10235311
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Escape vehicles may exhibit a condition where the low beams turn on by themselves when vehicle is OFF for 10 minutes or more with diagnostic trouble code (DTC) B1533 stored in the body control module (BCM). This may be due to the internal logic within the headlamp switch. To correct this condition, replace the headlamp switch (service base PN: 11654). Refer Workshop Manual, Section 417-01.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Escape vehicles built on or before 28-Jun-2022 may encounter false blind spot information system (BLIS) alerts. This may be due to the original packaging of the side obstacle detection radar mounting brackets. To correct the condition, follow the Service Procedure to replace the side obstacle detection radar mounting brackets and configure the modules.
NHTSA source summary · Original PDF not reviewed by Recallfolio
For 2000-2024 Ford and Lincoln vehicles, swapping a module from a vehicle for diagnosis purposes is likely to cause errors and is not recommended. It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 Ford and Lincoln vehicles may exhibit a condition where the high voltage battery stops charging when connected to level 1 or level 2 chargers with an illuminated malfunction indicator lamp (MIL) and diagnostic trouble code (DTC) P2C94 stored in the secondary on-board diagnostic control module A (SOBDM). To restore charging capability, disconnect the off-board charging station charge handle from the vehicle charge port and reconnect. This condition does not affect vehicle durability and no additional diagnosis or service is required for this condition at this time. Inform customers that they can continue to drive the vehicle and engineering is currently working on a solution for this condition that is expected in June 2023. Replacement of the SOBDM will not resolve this condition. Monitor OASIS for additional information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Escape/Corsair, 2021-2022 Bronco Sport, and 2022 Maverick vehicles built on or before 23-Mar-2022 may exhibit a hard, stiff, and/or difficult to turn condition due to a lack of power steering assist during engine start-up with U3000 diagnostic trouble codes (DTCs) stored in the PSCM. Using the latest version of Ford Diagnosis and Repair System (FDRS) tool, select and run the PSCM - Reset the Power Steering Control Module (PSCM) application. After PSCM reset, perform an ignition cycle. Update the PSCM to the latest software level using FDRS tool. If the U3000 DTC returns, continue with diagnostics and repair direction using Workshop Manual (WSM), Section 211-02 > Power Steering > Diagnosis and Testing. For claiming, use causal part 3C529 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022 Escape vehicles built on 11-Oct-2021 and through 16-Aug-2022 equipped with intelligent adaptive cruise control may exhibit a condition where the speed limit sign recognition indicator does not flash in the instrument panel cluster (IPC) when the vehicle is driven over the speed limit tolerance. This may be due to a misconfigured IPC. To correct this condition, run the IPC-Configuration app using Ford Diagnosis and Repair System (FDRS). For claiming, use causal part 10849 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS Manual).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2023 Ford and Lincoln SYNC3 equipped vehicles may experience an inaccurate notification in the FordPassî/LincolnWayî app indicating Vehicle Has Entered Deep Sleep Mode. Vehicle Has Entered Deep Sleep Mode message is expected if the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SoC) drops below 50%. If the vehicle is going into deep sleep outside these conditions, this may be due to the telematics control unit (TCU) software. To correct this condition, follow the Service Procedure to update the TCU to the latest software. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2021-2023 Model Year Bronco Sport and 2020-2022 Model Year Escape Vehicles with a 3-cylinder 1.5L Engine Replacement of High-Pressure Fuel Injectors
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Escape/Corsair, 2021-2022 Bronco Sport, 2022 Maverick vehicles built on or before 23-Mar-2022 may exhibit driver assistance warning messages displayed in the instrument panel cluster (IPC): Pre-collision Assist Not Available, Cruise Control Not Available, Collision Warning Malfunction and/or Adaptive Cruise Control Malfunction. Diagnostic trouble code (DTC) U0415:00 may also be stored in the power steering control module (PSCM), DTC C0051:67 stored in the anti-lock brake system (ABS) module and DTC U0418:86 stored in the image processing module A (IPMA). This may be due to the software in the PSCM. Using the latest version of Ford Diagnosis and Repair System (FDRS) scan tool, update the PSCM to the latest software level. For claiming, use causal part 3C529 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2020-2022 Model Year Escape and Corsair, 2021-2022 Bronco Sport and 2022 Maverick Vehicles Equipped With a 2.0L EcoBoost Engine Vehicle Emissions Control Information Label Update Owner Letters
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL · EQUIPMENT:OTHER:LABELS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Escape vehicles built on 1-Nov-2020 and through 29-Aug-2022 and 2021-2022 Bronco Sport vehicles built on or before 23-Sep-2022 may exhibit a moan noise when the vehicle is driven in reverse (R) in cold weather and/or high humidity. This may be due to the suspension sensitivity of the vehicle and interaction of the caliper housing with the pad backplate. To correct this condition, follow the Service Procedure to replace the rear caliper bushings.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2020-2022 Model Year Escape and Corsair, 2021-2022 Bronco Sport and 2022 Maverick Vehicles Equipped With a 2.0L EcoBoost Engine Vehicle Emissions Control Information Label Update
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Escape/Corsair vehicles may exhibit a door ajar warning lamp or higher than expected efforts to fully close doors. Verify the hood/liftgate are not open. Confirm all doors are fully closed and latches are fully engaged. Doors will not fully close when lightly letting go of the door or letting it swing closed from a short distance under its own weight. Push/pull effort must be applied to doors while closing to fully engage latch and turn off the ajar signal warning. If doors are still not fully latching closed, manually adjust door striker position to allow for proper alignment and engagement to the door latch. The door hang position may also need to be slightly adjusted to achieve the same effect. Refer to Workshop Manual (WSM), Section 501-03.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2022 Model Year Multiple Vehicle Lines Equipped with 8F35 Transmissions Transmission Replacement In all of the affected vehicles, the snap ring that is used to hold the 8F35 transmission clutch compression spring engaged was not fully seated in the assembly process. When the snap ring is not fully seated, the transmission will function as if the C clutch is partially engaged. The customer may experience rough shifts until the transmission can adapt to the clutch performance. There is a potential long term durability concern associated with the compromised function of the clutch.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Escape/Corsair, 2021-2022 Bronco Sport, 2022 Maverick vehicles may exhibit any of the following driver assistance warning messages displayed in the instrument panel cluster (IPC): Pre-collision Assist Not Available, Cruise Control Not Available, Collision Warning Malfunction and/or Adaptive Cruise Control Malfunction. Diagnostic trouble code (DTC) U0415:00 may also be stored in the power steering control module (PSCM), DTC C0051:67 stored in the anti-lock brake system (ABS) module and DTC U0418:86 stored in the image processing module A (IPMA). This may be due to the software in the power steering control module (PSCM). To correct this condition, using the latest version of Ford Diagnosis and Repair System (FDRS) scan tool. Update the PSCM to the latest software level.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 22-2176 to increase the labor operation allowance and update the part list. Some 2020-2022 Escape/Corsair vehicles built on or before 3-Jan-2022, 2020-2022 Explorer vehicles built on or before 14-Feb-2022, 2020-2022 Aviator vehicles built on or before 07-Feb-2022 and 2021-2022 Bronco Sport vehicles built on or before 3-Dec-2021 may exhibit a slow fuel fill and/or spit back condition during refueling. This may be due to the design of the fuel tank filler pipe. To correct the condition, follow the Service Procedure to replace the fuel tank filler pipe.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Escape/Corsair, 2021-2022 Bronco Sport, and 2022 Maverick vehicles may exhibit a hard, stiff, and/or difficult to turn condition due to a lack of power steering assist during engine start-up with various U3000 diagnostic trouble codes (DTCs) and/or U3000:66. To correct this condition, using the latest version of Ford Diagnosis and Repair System (FDRS) tool, select and run the PSCM - Reset the Power Steering Control Module (PSCM) application. After PSCM reset, perform an ignition cycle. Update the PSCM to the latest software level using (FDRS) tool. If DTCs U3000 returns, continue with diagnostics and repair direction using Workshop Manual (WSM), Section 211-02 > Power Steering > Diagnosis and Testing. For claiming, use causal part 3C529 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: POWER TRAIN · STEERING:STEERING CONTROL MODULE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Escape/Corsair/F-53 Motorhome/F-59 Commercial Stripped Chassis, 2021-2023 F-650/F-750/E-Series, and 2021-2022 Bronco Sport vehicles may exhibit an intermittent no crank/no start condition and/or an intermittent blank instrument panel cluster (IPC)/SYNC touchscreen. This may be due to the software in the gateway module (GWM). To correct the condition, reprogram the GWM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming use causal part 14F642 and the applicable labor operations of Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: BACK OVER PREVENTION:SOFTWARE · ENGINE AND ENGINE COOLING:ENGINE:CRANK/CAMSHAFT POSITION SENSOR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2021 Expedition/Navigator, 2020-2022 F Super Duty/Explorer, 2021-2022 Bronco/Corsair/Escape/Bronco Sport, 2022 Maverick vehicles may exhibit the wireless charger inoperative or poor performance when using some Apple iPhone models that use MagSafe wireless charging including iPhone 12 and 13. This may be due to limited compatibility with the wireless accessory charging module (WACM). To correct the condition, follow the Service Procedure to update the WACM. Note: The WACM software is designed to improve the compatibility between some Apple MagSafe charging iPhones, including iPhone 12 and 13 models, and the Ford Qi wireless charging module.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2023 Ford and Lincoln vehicles equipped with a telematic control unit (TCU) may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization, and/or modem electronic serial number (ESN) could not be displayed in the center display screen. To correct this condition prior to programming, remove the TCU fuse for 5-minutes then reinstall. Delete all previous session files for the vehicle. Start a new Ford Diagnosis and Repair System (FDRS) session. Perform a TCU provisioning and Program the TCU to the latest FDRS version level. If the concern is still present, follow normal diagnostics in Workshop Manual (WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Mustang Mach-E built on or before 17-Jan-2022, 2022 Escape built on or before 03-Mar-2022, Bronco Sport built on or before 04-Mar-2022, 2022 Maverick built on or before 25-Jan-2022 and 2022 Transit built on or before 17-May-2022 may exhibit a powertrain malfunction (wrench) indicator with diagnostic trouble code (DTC) P0929:77 stored in the gear shift module (GSM). This may be due to the software in the GSM. To correct this condition, perform Pinpoint Test D. Refer to Workshop Manual (WSM), Section 307-05 > Diagnosis and Testing. If the GSM is not operating correctly, perform the replacement of the GSM. Do not perform a PMI after installing a new GSM assembly. The GSM is shipped with the latest software level. For claiming, use causal part 7P155 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Escape/Corsair vehicles built on or before 17-May-2022 and 2021-2022 Bronco Sport vehicles built on or before 25-Feb-2022 may exhibit a hiss or rattle noise while driving. This may be due to an internal issue with the manual park release cable. If the noise is eliminated when the cable is disconnected from the transmission, install a new manual park release cable assembly LX6Z-7D246-T. Refer to the Workshop Manual (WSM), Section 307-05 > Automatic Transmission External Controls > Removal and Installation.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Escape vehicles built on 01-Oct-2020 and through 21-Jul-2022 and equipped with 1.5L engine and vacuum booster and 2021-2022 Bronco Sport vehicles built on or before 2-Dec-2021 may exhibit a squeal noise from the front brakes when applied at low or high speed. The alternate front brake disc (standard version) improves high frequency noise performance. To correct this condition, follow the Service Procedure to perform the replacement of the front brake discs.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022 Escape vehicles built on 01-Dec-2021 and through 30-Jun-2022 equipped with one-touch open driver window may exhibit a condition where the passenger rear door window is inoperative. The vehicle may also exhibit a rear door window motor overheating. This may be due to a continuous power supply of the driver door master window switch. To correct this condition, replace the driver door master window switch. Refer to the Workshop Manual (WSM), Section 501-11 Glass, Frames and Mechanisms > Removal and Installation. Let the affected window regulator motor to cool down for 1-2 minutes before operating the switch again. For claiming, use causal part 14529 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual. Note: The window regulator motor has thermal protection designed into the motor and will not be damaged
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Ford and Lincoln vehicles equipped with a telematic control unit (TCU) may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization, and/or modem electronic serial number (ESN) could not be displayed in the center display screen. To correct this condition prior to programming, remove the TCU fuse for 5-minutes then reinstall. Delete all previous session files for the vehicle. Start a new Ford Diagnosis and Repair System (FDRS) session. Perform a TCU provisioning and Program the TCU to the latest FDRS version level. If the concern is still present, follow normal diagnostics in Workshop Manual (WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: COMMUNICATION:MANUFACTURER TELEMATICS · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Bronco Sport 1.5L, 2019-2022 Edge/Nautilus, 2020-2022 Escape/Corsair, and 2022 Maverick vehicles may exhibit an illuminated AWD warning indicator or fault message with diagnostic trouble code (DTC) C0095:71/:19 stored in the all wheel drive (AWD) module. Some 2021-2022 Bronco Sport 2.0L may exhibit an illuminated AWD warning indicator or fault message with DTC C05D9:71, C05E8:71, C05D8:19 and/or C05E7:19 stored in the AWD module. This may be due to a rear drive unit (RDU) motor magnet ring misalignment. RDU assembly replacement is no longer required. To correct the condition, replace the RDU motor which is now available separately for service. Refer to Workshop Manual, Section 205-02 for diagnosis and repair procedures. For claiming use causal part 4C210 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022 Escape and Bronco Sport vehicles equipped with 1.5L engines should not be taken out of transport mode before customer delivery to reduce the risk of driving performance issues such as: rough operation, idle quality, engine misfires, lack or loss of engine power. These conditions may occur due to carbon fouled spark plugs from repeated engine ignition starts without driving the vehicle to normal operation temperatures (82°C to 97°C) during cold weather. Make sure that the vehicles in stock are in transport mode. Refer to the Workshop Manual (WSM), Section 419-10 Malfunction Electronic Modules > General Procedures.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Mustang Mach-E vehicles built on 01-Aug-2021 and through 18-Jan-2022, 2022 Maverick vehicles built on 13-Sep-2021 and through 18-Jan-2022, 2022 Escape vehicles built on 24-Sep-2021 and through 18-Jan-2022, 2022 Bronco Sport vehicles built on 08-Nov-2021 and through 18-Jan-2022 may exhibit a shift knob can be rotated without stepping on the brake pedal, although the transmission remains in park (P). This condition may be intermittent, more noticeable in warmer temperatures. DTC P0929 may also be set in the gear shift module (GSM). This may be due to a GSM concern. To correct the condition, follow the Service Procedure to update the GSM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Mustang Mach-E, 2022 Escape/Bronco Sport/Maverick/Transit vehicles may exhibit a powertrain malfunction (wrench) indicator with diagnostic trouble code (DTC) P0929:77 stored in the gear shift module (GSM). This may be due to the software in the GSM. To correct this condition, reprogram the GSM module using the latest software level of the Ford Diagnosis and Repair System (FDRS). For claiming, use causal part 7P155 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Escape and 2022 Bronco Sport vehicles may exhibit a moan noise when the vehicle is driven in reverse (R) in cold weather and/or high humidity. This may be due to the suspension sensitivity of the vehicle. To correct this condition, follow the Service Procedure to replace the rear caliper bushings.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2022 Ford and Lincoln vehicles equipped with the 8F35 transmission built on or before 16-Mar-2022 may exhibit transmission slip during acceleration from a stop when hot. This may be due damaged internal case half pump seals (7N265). To correct the condition, remove the transmission and replace the internal case half pump seals. Refer to Workshop Manual (WSM), Section 307-01.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Escape/Corsair/F-53 Motorhome/F-59 Commercial Stripped Chassis, 2021-2023 F-650/F-750/E-Series, and 2021-2022 Bronco Sport vehicles may exhibit a communication fault with emissions inspection equipment. This may be due to the software in the gateway module (GWM). To correct this condition, reprogram the GWM to latest software level using the appropriate Ford diagnostic scan tool. Use causal part 14F642 and applicable labor times from Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: ELECTRICAL SYSTEM:SOFTWARE · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Escape/Corsair, 2021-2022 Bronco Sport and 2022 Maverick vehicles may exhibit a condition where the door(s) do not open using the exterior door handle(s). This may be due to an enabled permanent engagement inertia lock within the exterior door handle, this condition occurs when the doors are closed or opened with excessive force. To correct this condition, follow the Service Procedure to properly disengage the permanent engagement inertia lock clip to allow the exterior door handle(s) to fully extend and open the door(s) from the outside.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022 Escape and Bronco Sport vehicles may exhibit a powertrain malfunction (wrench) indicator with diagnostic trouble code (DTC) P0929:77 stored in the gear shift module (GSM). This may be due to the software in the GSM. To correct this condition, reprogram the GSM module using the latest software level of the Ford Diagnosis and Repair System (FDRS). For claiming, use causal part 7P155 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: BACK OVER PREVENTION:SOFTWARE · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2022 Ford and Lincoln vehicle owners may experience a condition of missing authorization, command and control, battery charging details or phone-as-a-key setup buttons/selections in their FordPass or LincolnWay App. This condition is due to an error within the FordPass or LincolnWay App and not due to a concern on the vehicle. Verify that the customers FordPass or LincolnWay App is at the latest version. Replacement or reprogramming of the telematics control unit (TCU)/gateway module (GWM)/remote function actuator (RFA) will not resolve this condition. If the condition persists, utilize the FordPass Guides or Lincoln Way Concierge teams.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Escape/Corsair vehicles built on or before 3-Jan-2022, 2020-2022 Explorer vehicles built on or before 14-Feb-2022, 2020-2022 Aviator vehicles built on or before 07-Feb-2022 and 2021-2022 Bronco Sport vehicles built on or before 3-Dec-2021 may exhibit a slow fuel fill and/or spit back condition during refueling. This may be due to the design of the fuel tank filler pipe. To correct the condition, follow the Service Procedure to replace the fuel tank filler pipe.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2023 Ford or Lincoln vehicles with modems activated through FordPass or LincolnWay may experience 12 volt battery drain symptoms when the customer uses non-Ford/Lincoln phone applications as an alternate channel to access vehicle commands such as door lock/unlock, remote start, vehicle location, etc. The battery drain may be caused by excessive calls for data through the vehicle network keeping it in an activated state. Recommend that the customer uninstall the app to ensure this is not contributing to battery symptoms experienced. Advise the customer that unaffiliated third-party app developers do not work directly with Ford to adhere to security, vehicle communication, and privacy requirements.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Escape/Corsair, 2021-2022 Bronco Sport, 2022 Maverick vehicles may exhibit any of the following driver assistance warning messages displayed in the instrument panel cluster (IPC): Pre-collision Assist Not Available, Cruise Control Not Available, Collision Warning Malfunction and/or Adaptive Cruise Control Malfunction. Diagnostic trouble code (DTC) U0415:00 may also be stored in the power steering control module (PSCM), DTC C0051:67 stored in the anti-lock brake system (ABS) module and DTC U0418:86 stored in the image processing module A (IPMA). This may be due to the software in the power steering control module (PSCM). To correct this condition, using the latest version of Ford Diagnosis and Repair System (FDRS) scan tool. Update the PSCM to the latest software level.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2020-2022 Escape, 2021-2022 Corsair, 2022 Maverick vehicles equipped with HF35/HF45 hybrid transmissions can now be disassembled to repair and clean any contamination that may have been the result of a differential or transfer shaft bearing failure and the transmission can be overhauled/rebuilt. Service tools and service parts are now available. Refer to the Workshop Manual, Section 307-01.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021 and 2022 Ford and Lincoln vehicles may experience a tire sidewall wavy/indentation appearance in the radial direction on one or both sidewalls. Sidewall wavy/indentation appearance is a common cosmetic characteristic of radial tire construction and will not affect the performance of the tire.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Escape/Corsair, 2021-2022 Bronco Sport, 2022 Maverick vehicles equipped with 4-wheel drive (4WD) may exhibit a grinding/rubbing noise from floor pan/underbody area. This noise will be most noticeable on tip in acceleration and may be due to a mispositioned fuel tank heat shield. To correct the condition, follow the Service Procedure to reposition the fuel tank heat shield.
NHTSA source summary · Original PDF not reviewed by Recallfolio
In various 2017-2022 Ford and Lincoln vehicles, customers may receive a message in the FordPass or LincolnWay App stating "Feature Unavailable. Since this is a fleet vehicle, it cannot access the (SYNC Connect) FordPass or LincolnWay app through the TCU Embedded Modem. If this message appears, the vehicle may be equipped with a fleet telematics module. Replacement of the TCU or TCU related repairs will not prevent this message from appearing. Please refer the customer to in app FordPass Guides or LincolnWay Concierge Teams to aid with fleet telematics removal. Open app, select Account > Help > CHAT or CALL option
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 21-2236 to update the models and year affected. Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2013-2022 Escape, 2015-2018 Focus, 2015-2019 MKC, 2015-2022 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2022 F-Super Duty, 2018-2022 EcoSport/Expedition, 2019-2022 Ranger/Nautilus, 2021-2022 Bronco/Bronco Sport/Mustang Mach-E, 2022 Maverick vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022 Ford and Lincoln vehicles may need to perform A/C leak detection diagnostics. The 2022 Workshop Manual (WSM), Section 412-00 for A/C leak detection diagnosis is incomplete and is in the process of being updated. At this time, Pinpoint Test AN of Section 412-00 in the 2022 F-150 WSM can be used temporarily for the service procedure and specifications. Use the correct vehicle specific removal and replacement sections as needed. A new labor operation 19700A45 has also been released to align with the new procedure.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 20202022 Escape/Aviator plug-in hybrid electric vehicle (PHEV) and 20212022 Corsair PHEV vehicles may exhibit a FordPass or LincolnWay App message notification indicating deep sleep mode and connectivity is temporarily unavailable while the vehicle is plugged in during high voltage battery charging. The vehicle may also exhibit an inoperative remote start feature and/or lock and unlock functionality. This may be due to the software in the telematics control unit (TCU). To correct this condition, follow the Service Procedure to reprogram the TCU.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022 Maverick and 2020-2022 Escape vehicles equipped with a 2.5L full hybrid electric vehicle (FHEV) powertrain may exhibit an idle surge and/or rough idle with high temperature in the catalytic convertor and sulfur odor in the cab. This may be due to the software installed in the powertrain control module (PCM). This condition does not affect vehicle durability and no additional diagnosis or service is required for this condition at this time. Inform customers that they can continue to drive the vehicle and engineering is currently developing a software update that is expected in the last week of March 2022. Once the software update is available, contact the customer and schedule a follow-up appointment for repair. Monitor OASIS for updates.
Source components: ELECTRICAL SYSTEM:SOFTWARE · ENGINE AND ENGINE COOLING · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Escape vehicles equipped with an HF45 transmission may exhibit a rattle noise on cold start up only when the engine is running. This noise may be more prevalent in cold weather conditions, typically at or below 0ðC (32ðF). This may be due to the software in the secondary on-board diagnostic control module C (SOBDMC) and on some vehicles also from the flywheel damper assembly. To correct this condition, follow the Service Procedure steps to reprogram the SOBDMC and if necessary replace the flywheel damper assembly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2018 Focus/MKX/C-MAX, 2017-2019 MKC/Taurus/Flex/MKT, 2017-2020 Fusion/MKZ/Continental, 2017-2022 Mustang/Edge/Explorer/Police Interceptor Utility/Escape/F-150/F-Super Duty, 2018-2022 Expedition/Navigator, 2019-2022 Ranger/Nautilus, 2020-2022 Corsair/Aviator, and 2021-2022 Mustang Mach-E vehicles may exhibit a noisy, incorrectly operating, and/or inoperative seat motor. This may be due to a damaged or inoperative seat track motor. A lower level service part has been released to correct noisy, incorrect operation/inoperative seat track motors.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019-2022 Edge/Nautilus, 2020-2022 Escape/Corsair, and 2021-2022 Bronco Sport vehicles equipped with a 2.0L EcoBoost or 2.3L EcoBoost may exhibit a lack of power with an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P02AB, P0243, P0299, P25B3, P25B4, P2AB7, P2AB8 and/or P2AB9. This may be due to an inoperative wastegate actuator, missing wastegate actuator e-clip or non-visible damage to the actuator rod. If the diagnostic procedures lead to replacement of the turbocharger assembly, note that a lower level service component has been released K2GZ-9G488-B for Edge/Nautilus/Escape/Corsair/Bronco Sport for service to replace the actuator, actuator rod and both e-clips instead of a complete turbocharger assembly. When replacing the wastegate actuator, it is required to replace all parts included in the service kit.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2021 Explorer/Aviator/Escape/Corsair, 2021-2022 Bronco Sport, and 2022 Maverick vehicles may exhibit an inoperative driver door window control switch (windows inoperative, mirror control unresponsive, etc.). Diagnostic trouble code (DTC) B1088:87 may be present in the driver door module (DDM). This may be due to the software in the DDM. To correct the condition, reprogram the DDM with the latest software level of the Ford Diagnosis and Repair System (FDRS). After reprogramming the DDM, run the DDM configuration application and perform a window learn routine via FDRS. For claiming, use causal part 14B291 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:WIRING:SWITCHES/KNOBS/BUTTONS · STRUCTURE:BODY · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Escape, 2021-2022 Bronco Sport and 2022 Maverick vehicles may require servicing of the interior door handle lock cable mounting bracket on the interior door handle. The interior door handle cable mounting bracket, part number right hand LJ6Z-78431B14-A and left hand LJ6Z-78431B15-A are now available to service separately from the cables and latch mechanisms. It is no longer necessary to replace the complete latch assembly for a damaged interior door handle lock indicator mounting bracket.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Escape/Corsair vehicles may exhibit a door ajar warning indicator or higher than expected efforts to fully close doors. Verify the hood/liftgate are not open. Confirm all doors are fully closed and latches are fully engaged. Doors will not fully close when lightly letting go of the door or letting it swing closed from a short distance under its own weight. Push/pull effort must be applied to doors while closing to fully engage latch and turn off the ajar signal warning. If doors are still not fully latching closed, manually adjust door striker position to allow for proper alignment and engagement to the door latch. The door hang position may also need to be slightly adjusted to achieve the same effect. Refer to Workshop Manual (WSM), Section 501-03.