The vehicle dossier US · 2022
2022 Ford
EDGEProblems & recalls
130 distinct owner reports in the NHTSA snapshot. Other components appears in 58 of them. Explore what was reported—and which official actions are on file.
01 / Owner-reported evidence
What owners reported.
Categories attached to 130 distinct reports. A report can mention more than one component, so category totals can overlap.
See original component labels
These are reports made to NHTSA, not verified diagnoses. More reports can reflect more vehicles, more time on the road, or greater reporting activity.
The reporting timeline
When reports arrived.
Reports by year filed, not by the year a problem occurred. Showing the latest 5 years with reports.
59,000 miles is the median among 34 reports with usable mileage. The middle half spans 20,000–70,000 miles.
This describes the submitted reports. It does not predict when a vehicle will fail.
02 / Official safety campaigns
5 recall campaigns on file.
A campaign can cover only certain production dates or configurations. The count does not tell you whether an individual car has an open recall.
BACK OVER PREVENTION:SOFTWARECampaign 26V124000
Reported concern
Ford Motor Company (Ford) is recalling certain 2021-2026 Ford Bronco and 2021-2024 Ford Edge vehicles. The Accessory Protocol Interface Module (APIM) may overheat and shutdown, which can prevent the rearview camera image from displaying as intended.
Manufacturer’s stated response
The APIM software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. Owner notification letters were mailed April 13, 2026. Owners may contact Ford Customer Service at 1-866-436-7332. Ford's number for this recall is 26S09. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on March 5, 2026.
Manufacturer campaign: 26S09
Read campaign 26V124000 at NHTSABACK OVER PREVENTION:SOFTWARECampaign 25V315000
Reported concern
Ford Motor Company (Ford) is recalling certain 2021-2024 Bronco, F-150, 2021-2024 Edge, 2022-2025 Escape, F-250, F-350, F-450, F-550, F-600, 2022-2024 Expedition, 2022-2025 Transit, 2021-2023 Mach-E, 2024 Ranger, Mustang, 2021-2023 Lincoln Nautilus, 2022-2024 Navigator, and 2023-2024 Corsair vehicles. A software error may cause the rearview camera image to delay, freeze, or not display when the vehicle is in reverse.
Manufacturer’s stated response
The accessory protocol interface module (APIM) software will be updated by a dealer or through an over-the-air update, free of charge. This will be a phased campaign, with the remedy becoming available in different phases based on model and model years. Interim letters notifying owners of the safety risk were mailed on June 26, 2025. Additional letters will be mailed once the final remedy is available on each phase. Owner notification letters were sent on October 8, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S49.
Manufacturer campaign: 25S49
Read campaign 25V315000 at NHTSABACK OVER PREVENTION:SOFTWARECampaign 25V160000
Reported concern
Ford Motor Company (Ford) is recalling certain 2021-2022 Edge vehicles previously repaired incorrectly under recall number 22V-151. A software error may cause the rearview camera to display a blank or distorted image when the vehicle is in reverse.
Manufacturer’s stated response
Dealers will update the rearview camera software, free of charge. Owner notification letters were mailed April 25, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S28.
Manufacturer campaign: 25S28
Read campaign 25V160000 at NHTSAENGINE AND ENGINE COOLING:ENGINE:HARD PARTS INTERNAL/MECHANICALCampaign 24V635000
Reported concern
Ford Motor Company (Ford) is recalling certain 2021-2022 Bronco, F-150, Edge, Explorer, Lincoln Nautilus, and Lincoln Aviator vehicles equipped with either a 2.7L or 3.0L Nano EcoBoost engine. The engine intake valves may break while driving, which can result in engine failure and a loss of drive power.
Manufacturer’s stated response
Dealers will perform an engine cycle test and replace the engine as necessary, free of charge. Owner notification letters were mailed July 3, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 24S55.
Manufacturer campaign: 24S55
Read campaign 24V635000 at NHTSABACK OVER PREVENTION:DISPLAY FUNCTIONCampaign 22V151000
Reported concern
Ford Motor Company (Ford) is recalling certain 2021-2022 Edge vehicles. A software error may cause the rearview camera to display a blank or distorted image when the vehicle is in reverse.
Manufacturer’s stated response
The rearview camera software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. Owner notification letters were mailed on April 29, 2022. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 22S14.
Manufacturer campaign: 22S14
Read campaign 22V151000 at NHTSA03 / The manufacturer’s record
Instructions. Updates. Responses.
98 distinct communications list this model-year. Showing the latest 12. A matching model-year does not establish that every engine, trim or reported symptom is covered.
SSM 55031Some 2021-2026 Ford/Lincoln vehicles may exhibit various symptoms including but not limited to the auto start/stop system not operating as intended with a "Check Charging System" message in the instrument panel cluster (IPC) wh…NHTSA ID 11035269
Some 2021-2026 Ford/Lincoln vehicles may exhibit various symptoms including but not limited to the auto start/stop system not operating as intended with a "Check Charging System" message in the instrument panel cluster (IPC) while the charging system is operating properly with no charging related diagnostic trouble codes (DTC) stored. This may be due to someone using an aftermarket programmer to change the body control module (BCM) configuration to disable the auto start/stop system or perform other unsupported programming modifications. To correct this condition on F-150 and Bronco vehicles, download and run the Ford Diagnosis and Repair System (FDRS) application titled "BCM-Charging System Configuration Correction". Running this application will determine if the BCM configuration was modified by the customer and if so, provide the option to return the configuration back to factory settings. For other vehicle models exhibiting concerns related to unsupported aftermarket BCM programming, submit a Technical Support Request (TSR) requesting support to revert the BCM configuration
Components: ELECTRICAL SYSTEM · FUEL/PROPULSION SYSTEM · UNKNOWN OR OTHER. Confirm detailed applicability in the original document.
Source record 11035269 at NHTSATSB 26-2341This bulletin supersedes 26-2171. Reasons for update: update the Parts list to add a note to clarify the application of the part numbers W520102-S442 and 4S4Z-3N324-AA "FWD Only". Some of the vehicles listed in the Model statem…NHTSA ID 11035231
This bulletin supersedes 26-2171. Reasons for update: update the Parts list to add a note to clarify the application of the part numbers W520102-S442 and 4S4Z-3N324-AA "FWD Only". Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: Shudder condition, most noticeable at speeds below 60 mph (100 km/h) No relevant diagnostic trouble codes (DTC) present Traceable shudder event with IDS/FDRS reading *(Figure 1)* This condition may be perceived/felt as an engine misfire. This may be due to a concern with the output planetary assembly.
Components: POWER TRAIN · UNKNOWN OR OTHER. Confirm detailed applicability in the original document.
Source record 11035231 at NHTSASSM 55028Some 2021-2024 Ford and Lincoln vehicles may exhibit an "Updating SYNC" message on the vehicle center display screen after an over the air (OTA) update. The message can be cleared from the center display screen and SYNC can be …NHTSA ID 11035267
Some 2021-2024 Ford and Lincoln vehicles may exhibit an "Updating SYNC" message on the vehicle center display screen after an over the air (OTA) update. The message can be cleared from the center display screen and SYNC can be used normally, but it will re-appear at every subsequent ignition cycle. Inform customers that engineering is currently working on a software update solution for this condition to be delivered OTA expected in late Q3 2026. Software will update automatically if vehicle connectivity is enabled in the vehicles settings. Monitor Professional Technician System (PTS) for additional information.
Components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER. Confirm detailed applicability in the original document.
Source record 11035267 at NHTSATSB 26-2328This bulletin supersedes 26-2194. Reason for update: update the Parts list to correct a part description " Loctite 638", update the claim quantity for the drain/fill plug, update the claim quantity of the wheel hub bolts (Corsa…NHTSA ID 11035099
This bulletin supersedes 26-2194. Reason for update: update the Parts list to correct a part description " Loctite 638", update the claim quantity for the drain/fill plug, update the claim quantity of the wheel hub bolts (Corsair) and limited the parts list for Edge/Nautilus to only the rear drive unit fluid. Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: Shudder chatter condition, most noticeable at low speeds turning No relevant diagnostic trouble codes (DTCs) present This may be due to internal rear drive unit (RDU) fluid contamination.
Components: POWER TRAIN · UNKNOWN OR OTHER. Confirm detailed applicability in the original document.
Source record 11035099 at NHTSATSB 26-2297Some of the vehicles listed in the model statement above equipped with SYNC4 may experience a blank center display screen or black center display after welcome animation. The rear-view camera will still function when shifting t…NHTSA ID 11034134
Some of the vehicles listed in the model statement above equipped with SYNC4 may experience a blank center display screen or black center display after welcome animation. The rear-view camera will still function when shifting the vehicle to reverse under these conditions.
Components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER. Confirm detailed applicability in the original document.
Source record 11034134 at NHTSAECG-26.2.11.4.1 EdgeQuality improvements include: - Enhanced system performance, disk usage limits and memory monitoringNHTSA ID 11033809
Quality improvements include: - Enhanced system performance, disk usage limits and memory monitoring
Campaign / software reference: ECG-26.2.11.4.1
Components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER. Confirm detailed applicability in the original document.
Source record 11033809 at NHTSATSB 26-2194This bulletin supersedes 25-2627. Reason for update: To add a Step to reprogram the all-wheel drive (AWD) module for Bronco Sport vehicles. Some of the vehicles listed in the Model statement above may exhibit all of the followi…NHTSA ID 11031619
This bulletin supersedes 25-2627. Reason for update: To add a Step to reprogram the all-wheel drive (AWD) module for Bronco Sport vehicles. Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: Shudder chatter condition, most noticeable at low speeds turning No relevant diagnostic trouble codes (DTCs) present This may be due to internal rear drive unit (RDU) fluid contamination.
Components: POWER TRAIN. Confirm detailed applicability in the original document.
Source record 11031619 at NHTSATSB 26-2184This bulletin supersedes 23-2028. Reason for updates: increase the labor time allowance to account for axle removal. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions:…NHTSA ID 11031614
This bulletin supersedes 23-2028. Reason for updates: increase the labor time allowance to account for axle removal. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: - Fuel tank not filling up beyond half full - Small amount of fuel leaking from vapor line connection - Stalling after start - Hard to start/extended crank
Components: FUEL/PROPULSION SYSTEM. Confirm detailed applicability in the original document.
Source record 11031614 at NHTSATSB 26-2171This article updates TSB 25-2154. Reasons for update: *Parts List *Service Procedure to replace the output planetary carrier assembly *Added 2023-2024 model year vehicles Some of the vehicles listed in the Model statement above…NHTSA ID 11031490
This article updates TSB 25-2154. Reasons for update: *Parts List *Service Procedure to replace the output planetary carrier assembly *Added 2023-2024 model year vehicles Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: Shudder condition, most noticeable at speeds below 60 mph (100 km/h) No relevant diagnostic trouble codes (DTC) present Traceable shudder event with IDS/FDRS reading *(Figure 1)* This condition may be perceived/felt as an engine misfire. This may be due to a concern with the output planetary assembly.
Components: ENGINE. Confirm detailed applicability in the original document.
Source record 11031490 at NHTSASYNC-26.2.0.16.2 Edge26S09 Recall Remedy -Update to enable rearview camera image to display when in reverse after infotainment screen thermal shutdownNHTSA ID 11031651
26S09 Recall Remedy -Update to enable rearview camera image to display when in reverse after infotainment screen thermal shutdown
Campaign / software reference: SYNC-26.2.0.16.2
Components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER. Confirm detailed applicability in the original document.
Source record 11031651 at NHTSASSM 54720Various 2020-2026 Ford and Lincoln vehicles equipped with blind spot information system (BLIS) may experience an inoperative blind spot monitoring with a "Blind Spot System Fault" message displayed in the instrument panel clust…NHTSA ID 11031263
Various 2020-2026 Ford and Lincoln vehicles equipped with blind spot information system (BLIS) may experience an inoperative blind spot monitoring with a "Blind Spot System Fault" message displayed in the instrument panel cluster (IPC). This may also be accompanied by diagnostic trouble codes (DTCs) B118C:11 and/or B118C:15 stored in the driver door module (DDM), and/or B118D:11 and/or B118D:15 stored in the passenger door module (PDM). This may be due to the wiring connector from the mirror to the BLIS module. If diagnostics lead to an internal mirror wiring harness fault, a new lower level BLIS light pigtail is now released for service. It is not necessary to replace the exterior mirror assembly. Use part number SC3Z-14A411-B to resolve the concern.
Components: ELECTRICAL SYSTEM · LANE DEPARTURE: BLIND SPOT DETECTION. Confirm detailed applicability in the original document.
Source record 11031263 at NHTSA24N12 S2Certain 2021 - 2022 Model Year Various Vehicles Engine Valve Inspection Test This submission includes : Technical Instructions Updated wording and description with additional photo.NHTSA ID 11030911
Certain 2021 - 2022 Model Year Various Vehicles Engine Valve Inspection Test This submission includes : Technical Instructions Updated wording and description with additional photo.
Components: ENGINE. Confirm detailed applicability in the original document.
Source record 11030911 at NHTSARecords below contain the NHTSA bulk summary unless a document-reviewed explainer is linked. A service bulletin is not a safety recall or a promise of a free repair. Records may be revised or superseded; verify the current document with the manufacturer.
04 / Agency investigations
Official inquiries.
An investigation is an inquiry into a potential concern. Its presence does not establish a defect, and a closed case does not certify a car’s condition.
Loss of Motive PowerEA23002
On July 22, 2022, the Office of Defects Investigation (ODI) granted a Defect Petition (DP22001) and opened a Preliminary Evaluation (PE22007) to investigate allegations of loss of motive power in model year (MY) 2021 Ford Bronco vehicles equipped with 2.7L EcoBoost engines. Complainants were reporting sudden engine failure while driving resulting in a loss of motive power, often without the ability to restart. During PE22007, the cause of engine failure and loss of motive power in the subject vehicles was determined to be intake valve fracture, and the full scope of vehicles affected by the subject defect was identified as all MY 2021-2022 Ford and Lincoln models equipped with either the 2.7L or 3.0L EcoBoost engines, referred to as the “Nano” engine family. If an intake valve fractures in the subject engines, it may drop into the cylinder and contact the piston, often resulting in catastrophic engine damage. On September 29, 2023, PE22007 was upgraded to an Engineering Analysis (EA23002) to further investigate the subject defect across the full scope of affected vehicles. During EA23002, ODI visited Ford facilities to review technical information related to intake valve fracture in “Nano” engines, coordinated with NHTSA’s Vehicle Research and Testing Center (VRTC), and analyzed updated field data relating the subject defect. Forensic analysis of fractured intake valves demonstrated that the defective components exhibited “grinding burn” or out of specification hardness in the area of the keeper grooves. The presence of grinding burn is evidence that during the groove grinding phase of production, the temperature of the valve became sufficiently high to alter the microstructure of the material and is indicative that the valve supplier’s manufacturing processes were not within control specifications. Grinding burn results in a hard, brittle microstructure and high residual stresses toward the surface of the valve. Through normal engine loading, a valve with grinding burn will likely fracture at the area of highest vulnerability, which is the third keeper groove. In its response to the EA23002 Information Request (IR) letter, Ford provided evidence of 396 customer complaints (including field reports), 825 warranty claims, and 936 engine exchanges. When considering both ODI and manufacturer failure report data, there have been reports representing 1066 unique vehicles within the subject vehicle population. Analysis of the failure report data demonstrates that vehicles equipped with potentially defective intake valves were built within a production “spike period” of May 2021 – October 2021. The beginning of the spike period corresponds to a ramp up in production at the valve supplier manufacturing facility, and the end of the spike period aligns with the implementation of several mid-production process improvements and the decision to change the metal alloy used to produce intake valves from “Silchrome Lite” to “Silchrome 1”. Ford began investigating the subject defect in July 2021, determined the root cause, and took corrective measures for the new production vehicles. Analysis of the failure report data demonstrates that these corrective actions were successful in eliminating the risk of intake valve fracture for subject vehicles produced after October 2021. However, Ford did not take any field action to address vehicles produced during the spike period, and in the several months following the implementation of the production changes, a significant number of field failures continued to occur. It is Ford’s assessment that not all valves produced during the spike period are defective, and that failures associated with the subject defect occur at low time in service. Analysis of the failure report data demonstrates that the vast majority of failures have occurred before 20,000 miles with over half of all reported failures occurring before 5,000 miles. The rate of reported failures related to the subject defect has steadily decreased since November 2021. ODI coordinated with NHTSA’s National Center for Statistics and Analysis (NCSA) to conduct statistical analysis and predict the number of future failures associated with the subject defect. The results of this analysis, and the trends identified through the failure report data are generally consistent with Ford’s assessment that defective intake valves will likely fail at a low time in service and indicate that the majority of subject vehicles equipped with defective valves have already experienced a failure. On August 23, 2024, Ford submitted recall 24V635 for subject vehicles equipped with “Nano” engines and built within the production spike period identified above (total population 90,736 vehicles). The remedy includes an inspection at a Ford/Lincoln dealership where the lifetime engine cycles of the vehicle will be determined. If a vehicle does not meet a threshold for lifetime engine cycles, the dealership will conduct a high RPM engine cycle accumulation procedure, which aims to identify if the vehicle is equipped with defective intake valves. Any vehicle that fails the accumulation procedure will receive an engine replacement under the recall. In addition to recall 24V635, Ford has stated that it will launch customer satisfaction campaign 24N12, which will provide extended warranty coverage to the subject vehicles through the earlier of 10 years or 150,000 miles. In view of the recall action being taken by Ford, ODI is closing this Engineering Analysis. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Recorded closure: Oct 31, 2024
Campaign reference in the source: 24V635
Find investigation EA23002Your next step
Take good questions
to the inspection.
Use these prompts with a qualified inspector. This page is research, not a diagnosis or a substitute for a hands-on inspection.