2019 Ford EDGE Manufacturer communications & TSBs.Page 2
Original record summaries, dates and identifiers for this model-year. Records 101–200 of 201, ordered newest first. Dated records on this page: Nov 14, 2018–Mar 19, 2021.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Mar 19, 2021Service Bulletin/Repair Instructions
TSB 21-2081
NHTSA communication ID: 10189788
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019-2021 Edge and 2019-2020 Nautilus vehicles built on or before 11-Mar-2021 and equipped with a 8F35 transmission may exhibit a shudder/buck/jerk while driving up to 35 mph (57 km/h). This may be due to the software in the powertrain control module (PCM). To correct this condition, follow the Service Procedure steps to reprogram the PCM and the transmission solenoid strategy.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2020 Edge, 2016-2018 MKX, and 2019-2020 Nautilus vehicles may require replacement of the roof opening panel track or frame for various conditions. When replacing the roof opening panel, the replacement component may have less magnet plates. In order to prevent any noise vibration or harshness (NVH) concerns, the magnets on the headliner around the roof opening panel that line up with the removed magnet plates should be discarded.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021 Mustang Mach-E vehicles may experience a concern of the alarm activating when an unlocked door is opened, the driver door does not unlock/open when pressing the door activation switch, or the door activation switch not lighting up. This may be due to a software configuration in the body control module (BCM). To correct the condition, reprogram the BCM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 15604 and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019-2020 Edge vehicles may exhibit a condition where the rear wiper continuously operates. This may be due to a pinched or damaged wire in the liftgate where the harness enters the liftgate causing a short to ground. To correct the condition, inspect the area where the wiring harness enters the liftgate and repair any damage found to the wiring.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019-2021 Edge/Nautilus, 2020-2021 Escape/Corsair, 2021 Bronco Sport vehicles equipped with all wheel drive (AWD) may exhibit chatter/shudder during low speed turning events due to fluid contamination. Drain and refill the rear drive unit (RDU), refer to Workshop Manual Section (WSM) 205-02. Drive for 8 km (5 miles) in stop and go conditions with right and left turns and re-evaluate. If the issue is still present, continue with WSM diagnostics. For claiming, use base (4000) causal part.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019-2020 Edge/Nautilus vehicles may exhibit an inoperative power liftgate with or without diagnostic trouble code U3000-49 stored in the rear gate trunk module (RGTM). This may be due to the RGTM software. To correct the condition, reprogram the RGTM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming use causal part 14B291 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2020 Ford and Lincoln vehicles equipped with TCU and WiFi Hotspot, May display Vehicle Hotspot feature not enabled on this vehicle when attempting to enter the Hotspot menu. When using the FordPass/Lincoln Way application, the customer may receive a message saying Wi-Fi has been disabled from this vehicle. Check the vehicle specifications or vehicle build information for the mfal code on the PTS website (Detailed Vehicle Specifications). If mfal = WAFAC or WAFAB do not replace the TCU, engineering is currently investigating this condition. Inform customers Ford is developing a software fix that is expected in early March. In the interim, let the customer know they can continue to drive the vehicle and schedule a follow-up appointment with the customer for early March. Monitor OASIS for updates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2021 F-150, 2016-2018 MKX, 2019-2021 Nautilus, 2015-2021 Edge, 2017-2019 Fusion, 2017-2020 MKZ And 2017-2020 Continental vehicles equipped with a 2.7L/3.0L EcoBoost engine may appear to have a low engine oil level if the proper procedures are not followed. Refer to the Owner's Manual > Maintenance > Engine oil check section. When checking the engine oil level after shutting off the engine wait at least 15 minutes prior to checking in order to allow the oil to drain back to the oil pan. The engine oil level can be checked immediately if the engine has not been started. When changing the engine oil the engine needs to be at normal operating temperature and the oil filter removed before draining the oil. Allow the oil pan to drain completely for up to 5 minutes. Check oil level after filling by following the oil level check procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019-2020 Edge/Nautilus/Ranger, 2020 Escape and 2020-2021 Corsair/Explorer vehicles equipped with a 2.0L/2.3L EcoBoost may exhibit a lack of power with an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P02AB, P0243, P0299, P1464, P25B3, P25B4, P2AB7, P2AB8 and/or P2AB9. This may be due to a missing wastegate actuator e-clip. A lower level service component has been released, K2GZ-9G488-B for Edge/Nautilus/Escape/Corsair vehicles and LB5Z-9G488-B for Explorer/Ranger vehicles, for service to replace the actuator, actuator rod and both e-clips. Turbocharger replacement is not necessary for missing wastegate actuator e-clips.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019 MKC, 2019-2020 Edge/Nautilus/Escape/Ranger, 2020 Corsair, 2019-2021 Explorer vehicles equipped with 2.0L and 2.3L EcoBoost engines may exhibit a light to moderate ticking type noise at idle (600-700 RPM). The noise is usually more prominent in the area of the high-pressure fuel pump, located on the top of the engine just behind the number 4 ignition coil. This noise is not detrimental to engine function and has no short or long-term effects on engine durability. This an operating characteristic of these engines and no repairs should be attempted.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2020 Ford and Lincoln vehicles may exhibit inoperative remote features via the Ford Pass/Lincoln Way mobile app, incomplete user authorization, no modem electronic serial number (ESN) displayed or DTCs U2100 and/or B156D in the telematics control unit (TCU). These symptoms may persist even after performing a TCU software update and/or replacement. To correct this condition, start a new session with the latest version of the appropriate diagnostic scan tool and perform a PMI on the TCU. If issues persist, open a hotline assistance request and include the IDS version (if applicable) used to perform the PMI and the Authorization Status PID value in the TCU datalogger. For claiming use causal part 14H092 and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: ELECTRICAL SYSTEM:SOFTWARE · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2020 Ford and Lincoln vehicles equipped with TCU and WiFi Hotspot, May display Vehicle Hotspot feature not enabled on this vehicle when attempting to enter the Hotspot menu. When using the FordPass/Lincoln Way application, the customer may receive a message saying Wi-Fi has been disabled from this vehicle. Check the vehicle specifications or vehicle build information for the mfal code. If mfal = WAFAC or WAFAB do not replace the TCU, engineering is currently investigating this condition. Inform customers Ford is developing a software fix that is expected in early January. In the interim, let the customer know they can continue to drive the vehicle and schedule a follow-up appointment with the customer for early January. Once the update becomes available, contact the customer and confirm the service appointment is going forward. Monitor OASIS for updates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019 MKZ, 2019-2020 EcoSport/Mustang/Continental/Fusion/F-150/Transit Connect/Ranger/Edge/Nautilus and 2020 Escape/Corsair/Aviator/Explorer/Expedition/Navigator/F-Super Duty vehicles with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019-2020 Edge/Nautilus vehicles may exhibit an inoperative power liftgate with diagnostic trouble code (DTC) B144F:79 stored in the rear gate trunk module (RGTM). This may be due to the calibration of the RGTM. To resolve the concern, reprogram the RGTM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming use causal part number 14B291 and Section 10 of the Service Labor Time Standards (SLTS) Manual. Do not replace the power strut unless DTC B144F remains after reprograming the RGTM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020 Edge/Nautilus vehicles built on 12-Aug-2020 and through 22-Aug-2020 may exhibit a customer concern of the FordPass or Lincoln Way mobile apps unable to connect to the vehicle. The customer may state that there is no activate button on the FordPass or Lincoln Way mobile app. This may be due to the telematics control unit (TCU) module. To correct the condition, reprogram the TCU using As-Built data. For claiming use causal component 14G087 and labor operations from Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2020 F-150/Mustang, 2016-2020 Edge, 2016-2018 MKX and 2019-2020 Nautilus vehicles built on or before 18-Jan-2020 may exhibit a mirror click and/or ratcheting noise when using memory functions or easy entry/exit function. This may be due to the software in the driver door module (DDM) and passenger door module (PDM). To correct the condition, reprogram the DDM and PDM with the latest software level of the appropriate Ford diagnostic scan tool. For claiming use causal part 14B291 and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2009-2020 Ford and Lincoln vehicles equipped with turbochargers may exhibit an oil leak from the turbocharger oil supply or return tubes, O-rings or 6.7L pedestal gasket. Although oil may collect on the turbocharger, it is very rare for a turbocharger to leak oil. To isolate the source of the leak, refer to Workshop Manual (WSM), Section 303-00 General Information > Diagnosis and Testing > Engine > Engine Oil Leaks - Fluorescent Oil Additive Method procedure. When an oil leak is present at a turbocharger oil supply or drain tube, remove the affected oil tube and inspect for damage, and replace the O-ring seals, pedestal gasket or oil tube as required. Refer to WSM, Section 303-04. For claiming, use the affected oil tube or pedestal gasket as the causal part and applicable labor operations in Sections 6 and 9 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2020 Edge, 2016-2018 MKX, and 2019-2020 Nautilus vehicles may exhibit the parking lamps stay on and/or the trailer lights flicker with vehicle turned off when a trailer is connected to the vehicle. This may be due to the software in the trailer module (TRM). To correct the condition, reprogram the TRM with the latest software of the appropriate Ford diagnostic scan tool. Use causal part 19H332 and applicable labor times from Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019 MKZ, 2019-2020 Mustang/Continental/Fusion/F-150/Transit Connect/ Ranger/Edge/Nautilus and 2020 Escape/Corsair/Aviator/Explorer/Expedition/ Navigator/F-Super Duty vehicles with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure.
Source components: BACK OVER PREVENTION: CAMERA SYSTEM · ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:SOFTWARE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2020 F-150, 2016-2018 MKX, 2019-2020 Nautilus, 2015-2020 Edge, 2017-2019 Fusion, 2017-2020 MKZ And 2017-2020 Continental vehicles equipped with a 2.7L/3.0L EcoBoost engine may appear to have a low engine oil level if the proper procedures are not followed. Refer to the Owner's Manual > Maintenance > Engine oil check section. When checking the engine oil level after shutting off the engine wait at least 15 minutes prior to checking in order to allow the oil to drain back to the oil pan. The engine oil level can be checked immediately if the engine has not been started. When changing the engine oil the engine needs to be at normal operating temperature and the oil filter removed before draining the oil. Allow the oil pan to drain completely for up to 5 minutes. Check oil level after filling by following the oil level check procedure.
Source components: ENGINE AND ENGINE COOLING:ENGINE:OIL/LUBRICATION · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019-2020 Edge/Nautilus vehicles may exhibit a false traction control or yaw control event. This may be due to software in the anti-lock braking system (ABS) module. To correct the condition, reprogram the ABS module using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 2B373 and labor times in Section 02 of the Service Labor Time Standards (SLTS) Manual.
Source components: ELECTRICAL SYSTEM:SOFTWARE · SERVICE BRAKES, AIR:ANTILOCK · TRACTION CONTROL SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019-2020 Edge vehicles may exhibit an Overspeed Warning message displayed in the IPC. The warning may display at 118 km/h (73 mph). To correct the condition, perform an as-built configuration of the IPC using the appropriate Ford diagnostic scan tool. For claiming, use causal part 10849 and applicable labor times from Section 10 in the Service Labor Time Standards (SLTS) Manual.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app , incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019 MKZ, 2019-2020 Mustang/Continental/Fusion/F-150/Transit Connect/ Ranger/Edge/Nautilus and 2020 Escape/Corsair/Aviator/Explorer/Expedition/ Navigator/F-Super Duty vehicles with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 19-2026 to update the vehicle model years affected. Some 2000 and newer Ford/Lincoln/Mercury vehicles equipped with aluminum body panels may exhibit corrosion concerns appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019-2020 Edge/Nautilus vehicles equipped with a 2.0L EcoBoost engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P0128, P0217, P044C, P1026, P1285, P1299, P139A and/or P2457 stored in the powertrain control module (PCM). The vehicle may also exhibit low coolant level, white smoke from the tailpipe, an over temperature warning in the instrument panel cluster (IPC), and/or an external coolant leak. This may be due to the exhaust gas recirculation (EGR) cooler and/or settings in the PCM software. To resolve the condition, inspect the EGR cooler and/or update the PCM software.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2020 F150/Edge/Fusion, 2016-2018 MKX, 2019-2020 Nautilus, and 2017-2020 Continental vehicles equipped with 2.7L EcoBoost engines may exhibit an illuminated malfunction indicator lamp (MIL) and/or Engine Coolant Over Temperature warning with diagnostic trouble codes (DTCs) P0116, P0117, P0118, P0119, P0128, P0217, P0330, P1026, P1299, and/or P130D. This may be due to the engine coolant temperature (ECT) sensor or knock sensor wiring harness. To correct the condition, replace the 12A648 ECT sensor and 12A699 knock sensor. Do not disconnect the ECT sensor from the knock sensor harness in case parts are called back for analysis. For claiming, use causal part 12A699 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019 F-150/Ranger/Continental/Edge/Nautilus/Mustang/Fusion/MKZ vehicles may experience voice prompts that skip or have short pauses while directions are being provided. Engineering is currently working on a solution for this condition. Please inform customers that Ford is developing a software fix that is expected in early August. In the interim, let the customer know they can continue to drive the vehicle and schedule a follow-up appointment with the customer for early August 2020. Once the update becomes available, contact the customer and confirm the service appointment is going forward. Monitor OASIS for updates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019 F-150/Ranger/Continental/Edge/Nautilus/Mustang/Fusion/MKZ vehicles may experience voice prompts that skip, hiccup or have short pauses while directions are being provided. No repairs should be made to attempt to correct this condition. Engineering is currently working on a solution for this condition. Please inform customers that Ford is developing a software fix that is expected in early August. Let the customer know they can continue to drive the vehicle and schedule a follow-up appointment with the customer for early to mid August 2020. Once the update becomes available, contact the customer and confirm the service appointment is going forward. Monitor OASIS for updates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2020 Ford and Lincoln vehicles equipped with a SYNC 3 Touchscreen may experience the volume control unresponsive from the Front Control Interface Module (FCIM) and steering volume controls when using Apple Car Play. When the Apple device is removed, volume control is restored. This is due to a concern with the Waze Navigation App software and Apple iOS version. To correct the condition, update the Waze App software and iOS to the latest version available and reboot the customer's Apple device. Perform an ignition cycle and reconnect the Apple device via USB. Open Apple Car Play and confirm volume control is restored. Installing/Updating third party software/applications is not warrantable.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019 Edge/Nautilus vehicles may exhibit a slow fuel fill and/or spit back during refueling. This may be due to the software in the powertrain control module (PCM). To correct the condition, follow the Service Procedure to reprogram the PCM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019-2020 Edge/Nautilus vehicles equipped with an 8F57 transmission may exhibit a harsh engagement when shifting from PARK to REVERSE, PARK to DRIVE and/or REVERSE to DRIVE with no DTCs present. The vehicle may also exhibit a harsh upshift and downshift. These harsh engagements may result in an engagement clunk from the driveline. This may be due to various powertrain control module (PCM) software parameters for harsh engagements when shifting from various shifter selector positions. To correct the condition, follow the Service Procedure to reprogram the PCM.
Source components: POWER TRAIN:DRIVELINE · POWER TRAIN:MANUAL TRANSMISSION:COLUMN SHIFT ASSEMBLY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2018 C-Max, 2013-2020 Escape/Fusion/MKZ, 2015-2018 Focus,2015-2019 MKC, 2015-2020 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2020 F-Super Duty, 2018-2020 EcoSport/Expedition, 2019-2020 Ranger/Nautilus vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
Source components: SEATS · STRUCTURE:FRAME AND MEMBERS:UNDERBODY SHIELDS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019-2020 Edge/Nautilus vehicles equipped with 2.0L EcoBoost engines built on or before 24-Jan-2020 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P2282 stored in the powertrain control module (PCM). This concern may be due to an intermittently stuck open brake vacuum tube assembly causing an uncommanded high air flow intake manifold leak. To resolve the condition, replace the brake vacuum tube assembly.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM) · SERVICE BRAKES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some customers may experience a notification in the FordPass and/or LincolnWay apps that indicates their vehicle has entered "deep sleep mode". This mode is enabled due to the vehicle not being started for 14 consecutive days or battery voltage is at/or below 9.5 volts. Some 2020 models will also set a warning if the telematic control unit (TCU) has received an automatic over the air update. The purpose of deep sleep mode is to conserve battery voltage. When deep sleep mode is enabled, the TCU is powered down and all communication with the FordPass and/or LincolnWay apps are disabled. To wake the vehicle from deep sleep mode, manually start the vehicle. More deep sleep mode information can be found in the FordPass or LincolnWay apps under: More > Guides > click in search entry box > type "deep sleep" and click on "Ask".
NHTSA source summary · Original PDF not reviewed by Recallfolio
SSM 48619 - Various Vehicles - Perimeter Alarm Armed And Original Vehicle Keys Cannot Be Accessed to Enter Vehicle - CAN Protection Strategy Some 2013-2016 Model Year Vehicles may exhibit a concern in which the Perimeter Alarm is active and the original keys cannot be accessed to disable the perimeter alarm. This concern would most often occur when a customer loses keys and the dealership is attempting to program new keys to the vehicle. The Workshop Manual (WSM), Section 419-01A Perimeter Anti-Theft Alarm - System Operation and Component Description has been updated to inform of the Controller Area Network (CAN) Protection Strategy. Follow the procedure outlined to prevent replacement of the Body Control Module (BCM) on CAN Protection Strategy equipped vehicles when original keys are lost and perimeter alarm is active. Refer to the WSM for further detail on the CAN Protection Strategy. Lost keys and replacement of BCM for lost keys is non-warrantable.
Source components: ELECTRICAL SYSTEM · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SSM 48608 - 2019 Edge - Ambient Air Temperature Inaccurate Some 2019 Edge vehicles may exhibit an incorrect or inaccurate ambient air temperature (AAT) reading. This may be due to the software in the front controls interface module (FCIM). To correct the condition, reprogram the FCIM with the latest software level of the appropriate Ford scan tool. For claiming use causal part 18842 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2020 vehicles equipped with the 8F24, 8F35, 8F40, or 8F57 transmissions may have a trace amount of transmission fluid in the main control electrical connector. This is due to the connector being submerged in transmission fluid during the main control manufacturing process. A trace amount should be considered normal and will not affect the function of the transmission. Do not attempt a repair for this condition. If more than a trace amount of fluid is found, follow normal diagnostics in the Workshop Manual(WSM), Section 307-01>Diagnosis and Testing>Leakage Inspection.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SSM 48558 - 2017-2020 Various Vehicles Equipped With Telematics Control Unit (TCU) - Various FordPass/LincolnWay Mobile App Concerns Some 2017-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2020 Escape/Corsair, Edge, Explorer, Fusion, Transit Connect Vehicles equipped with a TCU may exhibit a "Battery Backup Component Failure" message in the cluster. This may be accompanied by DTC 1477-09 - Backup Battery Component Failure. This may be due to the TCU experiencing a sudden temperature change. To correct this condition, reprogram the TCU using the appropriate Ford diagnostic scan tool. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2020 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2019 Edge/Continental, 2018 MKX and 2019 Nautilus vehicles built on or before 1-Aug-2019 and 2018-2019 Fusion/MKZ vehicles built on or before 15-Aug-2019 equipped with a 2.7L EcoBoost or 3.0L EcoBoost engine may exhibit an oil leak from the engine oil pan RTV seal. To correct the condition, follow the Service Procedure steps to replace the oil pan with a new oil pan equipped with a press in place gasket.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019-2020 Edge/Nautilus/Transit Connect and 2020 Escape/Corsair vehicles equipped with a 8F35 transmission may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0766 stored in the powertrain control module (PCM) and/or intermittent no reverse engagement concerns. This may be due to contamination in the main control valve body separator plate orifice. To correct the condition, follow the Service Procedure steps to clean the contamination from the main control plate.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2019 Expedition/Navigator, 2019 Edge/Nautilus, 2020 Explorer/Aviator vehicles equipped with a family entertainment system may experience an issue where the audio not synchronized with the video display when using the vehicle speakers. To correct this condition, contact the VOXX Customer Service Department at 1-866-869-7888. For claiming, refer to the Warranty and Policy manual for Ford Licensed Accessories.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019-2020 Edge/Escape/Nautilus/Corsair vehicles equipped with 2.0L EcoBoost engines may exhibit low coolant, white smoke from the tailpipe, an over temperature warning in the instrument panel cluster (IPC), external coolant leaking, and/or illuminated MIL with DTCs P0217, P0401, P1026, P1285, P1299, P2196 or P2467 stored in the PCM. This may be due to an EGR Cooler that is leaking coolant into the engine intake and exhaust system. The EGR cooler should be inspected first to detect the presence of any internal leaks by a visual inspection and a pressure test as defined in the Workshop Manual (WSM). If any coolant is found leaking from the coolant chamber into the exhaust chamber, replace the EGR cooler. If no issues are detected with the EGR cooler, continue repair diagnosis using standard diagnostic procedures as defined in the WSM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019 F150, Ranger, Continental, Edge, Nautilus, Mustang, Fusion or MKZ may experience voice prompts that skip, hiccup or have short pauses while directions are being provided. No repairs should be made to attempt to correct this condition. Engineering is currently investigating the concern. Monitor Oasis for updates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019 Edge/Nautilus vehicles equipped with an 8F35 transmission and built on or before 10-Sep-2019 may exhibit a harsh upshift and downshift, harsh engagements when shifting from PARK to REVERSE, PARK to DRIVE and/or REVERSE to DRIVE. These harsh engagements may result in an engagement clunk from the driveline. This may be due to various powertrain control module (PCM) software parameters for harsh engagements when shifting from various shifter selector positions. To correct the condition, follow the Service Procedure to reprogram the PCM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019 Edge/Nautilus vehicles equipped with an 8F57 transmission may exhibit a harsh upshift and downshift, harsh engagements when shifting from PARK to REVERSE, PARK to DRIVE and/or REVERSE to DRIVE with no DTCs present. These harsh engagements may result in an engagement clunk from the driveline. The vehicle may also exhibit a 4th to 5th gear upshift flare. This may be due to various powertrain control module (PCM) software parameters for harsh engagements when shifting from various shifter selector positions. To correct the condition, follow the Service Procedure to reprogram the PCM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019 Edge/Nautilus vehicles may exhibit harsh/bumpy upshift/downshifts, harsh engagements from PARK to REVERSE, PARK to DRIVE, REVERSE to DRIVE or DRIVE to REVERSE. The vehicle may also exhibit an upshift flare from 4th to 5th gear during the first shift after a cold start. This may be due to the shift strategy in the powertrain control module (PCM). Follow the Service Procedure.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019 Mustang, Continental, Fusion, MKZ, F150, Transit Connect, Ranger, Edge or Nautilus with SYNC 3 may have the following intermittent symptoms: a solid blue screen when moving forward at speeds above 16 kph (10 mph), the rear view camera remains on the screen at speeds below 16 kph (10 mph), or inoperative infotainment applications. This may be due to the SYNC 3 software version installed on the vehicle. To correct the condition, follow the Service Procedure steps to reprogram the accessory protocol interface module (APIM).
Source components: BACK OVER PREVENTION: SENSING SYSTEM: CAMERA · ELECTRICAL SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019 Edge vehicles built on or before 06-Mar-2019 may exhibit a popping or snapping noise from the rear of the vehicle when the liftgate is opened or closed. This may be due to reversing lamp close out interference caused by the securing tabs. To correct the condition, follow the Service Procedure steps to replace the reversing lamp close out. A lower level service part has been released. Replacement of the reversing lamp assembly is not required. To correct the condition, follow the Service Procedure steps on vehicles that meet the following criteria: * 2019 Edge * Built on or before 06-Mar-2019 * Popping/snapping noise when opening or closing the liftgate
Source components: ELECTRICAL SYSTEM · STRUCTURE:BODY:TAILGATE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2020 vehicles equipped with an EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function. To support the proper diagnosis of this compressor, the EVDC control valve tester has been provided to each U.S. dealership (339-EVDC100). Ensure the A/C system has a full charge prior to any compressor diagnostics. To support the proper diagnosis of this compressor, the EVDC compressor tool must be used, and the results recorded in the Technician comments field with the warranty claim. This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2019 Edge/Continental/Fusion/MKZ, 2018 MKX, and 2019 Nautilus vehicles equipped with a 2.7L EcoBoost or 3.0L EcoBoost engine may exhibit an oil leak from the engine oil pan RTV seal.To correct the condition, follow the Service Procedure.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2010-2020 vehicles may exhibit distorted glass with a subtle orange peel pattern or streaking etched into the surface. This is caused by hydrofluoric acid which is used in some car wash solutions as a cleaning agent. Hydrofluoric acid can attack the glass and cause visual distortion and/or discoloration on the outer surface which cannot be removed by further cleaning. If this type of distortion is found, inspect the area of the glass that is covered by the cowl and/or molding. The portion of glass that is covered by the cowl or molding will not be affected by the acid. Hydrofluoric acid damage is not a defect in material or workmanship and is not a warrantable condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
For Ford and Lincoln vehicles that require positive or negative battery terminal replacement, it is not necessary to replace the complete battery cable harness (14300 and 14301) for this concern. Positive battery cable clamp BT4Z-14450-AA and negative battery cable clamp BT4Z-14450-BA are available for this type of repair. Do not cut or shorten the battery cable, instead carefully remove the affected battery cable clamp and clean the cable end as necessary to preserve wire length. Some rework may be necessary for some vehicle environments. Bend the new positive battery cable clamp as needed and crimp it to the existing battery cable. Make sure to use heat shrink tubing over the battery cable to battery cable clamp connection. Obtain the heat shrink tube locally.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2019 vehicles may experience a no crank concern due to a security access key table error. When attempting to program keys or perform a parameter reset, the procedure may fail and the appropriate Ford diagnostic scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the body control module (BCM) is internally damaged and requires replacement. The BCM should only be replaced for this condition when the 232 key table error message is present. If the 232 key table error is not present, follow normal diagnostics for the no crank condition. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019 Edge/Nautilus vehicles equipped with an 8F57 transmission may exhibit harsh engagements when shifting from PARK to REVERSE, PARK to DRIVE and or REVERSE to DRIVE. These harsh engagements may result in an engagement clunk from the driveline. Do not attempt any repairs at this time. Engineering is investigating, monitor OASIS for updates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2019 Edge vehicles build on or before 5-Nov-2018 may exhibit snow and/or ice accumulation below the wiper blade park position, causing the wipers to have intermittent operational issues. If normal diagnostics do not result in a root cause determination, replace the drivers side wiper motor with updated service part FT4Z-17508-H, and make sure the customer is advised to keep the cowl area clean of ice and snow. Refer to Workshop Manual (WSM), Section 501-16 and applicable labor operations in Section 11 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019 Edge/Nautilus/Transit Connect vehicles equipped with a 8F35 transmission may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0766 stored in the powertrain control module (PCM) and/or intermittent or delayed reverse engagement concerns. This may be due to contamination in the main control valve body separator plate orifice. To correct the condition, follow the Service Procedure steps to clean the contamination from the main control plate.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019 Edge/Nautilus vehicles equipped with all-wheel drive (AWD) may exhibit an AWD System Disabled message in the instrument panel cluster (IPC) with diagnostic trouble code (DTC) C0095:99. This may be due to the calibration of the AWD module. Using the latest software level of the appropriate Ford diagnostic scan tool, reprogram the AWD module. For claiming, use causal part 4000 and applicable labor times from Section 10 in the Service Labor Time Standards (SLTS) Manual.
Source components: ELECTRICAL SYSTEM · EQUIPMENT ADAPTIVE/MOBILITY · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2018 Edge and 2015-2019 Fusion/MKZ/Escape/MKC vehicles equipped with a 2.0L EcoBoost engine may exhibit a low coolant level, white exhaust smoke and/or a runs rough condition with or without an illuminated malfunction indicator lamp (MIL). Diagnostic trouble codes (DTCs) may include P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To correct the condition, follow the Service Procedure steps to replace the long block engine assembly.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2019 F-150 vehicles built on 23-Sep-2018 and through 28-Mar-2019 and 2019 Edge/Nautilus/Continental/MKZ vehicles built on 4-Dec-2018 and through 29-Mar-2019 and Fusion vehicles built on 16-Jan-2019 and through 12-Apr-2019 equipped with a 2.7L/3.0L EcoBoost engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P04DB stored in the powertrain control module (PCM). This may be due to the incorrect positive crankcase ventilation (PCV) valve installed. If the PCV valve is brown in color, refer to the Powertrain Control/Emissions Diagnosis (PC/ED) Manual for normal diagnostics. If the PCV valve is gray in color, replace the PCV valve, clear the DTC, and retest. If the DTC returns, refer to the PC/ED for normal diagnostics.
Source components: ENGINE AND ENGINE COOLING · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV).
NHTSA source summary · Original PDF not reviewed by Recallfolio
2019 Edge and Nautilus vehicles, equipped with AWD and built on 22-Jan-2019 and through 03-Mar-2019, exhibit a noise from the rear of the vehicle when a door is opened or after KOEO/KOER. The rear drive unit (RDU) in these vehicles uses a brushless DC motor to vary the amount of torque to the rear axle, and during functional verification, it produces a noticeable noise that is a normal function of the RDU. If the noise appears abnormally loud, it is recommended to compare the noise from the customers vehicle with a 2019 AWD Edge or Nautilus built before 22-Jan-2019 or after 03-Mar-2019, in a similar environment (i.e. both outside). If the noise in the customers vehicle is determined to be significantly louder than a similar vehicle built outside the build dates, do not disassemble the RDU for further diagnosis, an updated RDU assembly is available.
NHTSA source summary · Original PDF not reviewed by Recallfolio
On vehicles equipped with an automatic transmission it is imperative that the converter pilot hub be greased with Motorcraft Multi-Purpose Grease Spray XL-5-A even if grease was not applied from the factory. Also verify that the engine/transmission alignment dowel pins are present as well as the engine crankshaft dowel pin, if equipped, when installing the transmission. Failure to adequately lubricate the converter hub greatly increases the likelihood of the flexplate cracking in the future. Missing dowels may cause a misalignment issue also resulting in a premature failure. Refer to Workshop Manual (WSM), Section 307-01.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2019 vehicles equipped with a EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SSM 47948 - 2010-2019 Various Vehicles - Turbocharged Engines - Oil Supply Filter Replacement When Replacing The Turbocharger Or The Turbocharger Oil Supply Tube For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. When specified in the WSM, the turbocharger oil supply filter must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2019 vehicles equipped with a EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.
Source components: ELECTRICAL SYSTEM · EQUIPMENT:APPLIANCE:AIR CONDITIONER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019 Edge/Nautilus vehicles equipped with 2.0L EcoBoost engines built on or before 15-Mar-2019 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P2282 stored in the powertrain control module (PCM). This concern may be due to an intermittently stuck open brake vacuum tube assembly causing an uncommanded high air flow intake manifold leak. To resolve the condition, replace the brake vacuum tube assembly.
Source components: ENGINE · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SSM 47925 - 2019 Various Vehicles - SYNC 3 - Infotainment Screen Concerns, Wi-Fi ConnectionMessage, Rear View Camera Operation Some 2019 vehicles equipped with SYNC 3 may have the following intermittent symptoms: a Wi-Fi connection pop up every key cycle, frozen unresponsive screen, a solid blue screen when moving forward at speeds above 10 mph, the rear view camera remains on the screen at speeds below 10 mph, or poor App performance. To resolve this concern, check for a SYNC software update under the OASIS Tab SYNC selection. If an update is available, update the APIM software per Workshop Manual (WSM), Section 415-00. Follow the onscreen instructions provided by the programming process. To verify success after programming, turn the key off with the dooropen for 5 minutes. Perform this SYNC programming before taking any other repair steps. For claiming, use causal part 14G371 and applicable labor operations inSection 10 of the SLTS manual. APPLICABLE VEHICLES
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT:ELECTRICAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
SSM 47922 - Various Vehicles - 2.7L/3.0L EcoBoost Engine - Oil Filter Service Tip When servicing the oil filter on vehicles equipped with a 2.7L or 3.0L EcoBoostengine it is critical to inspect the oil filter housing center stem to verify is not separated or damaged. If the center stem is damaged or separated from the housing this will result in oil flow through the reservoir drain port causing low engine oil pressure and internal engine damage. If the filter housing stem is damaged or separated, the oil filter housing must be replaced. If the center stem is not damaged or separated, the O-ring seals on the stem and housing must be replaced each time the filter is serviced.
Source components: ENGINE · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019 Edge and Nautilus vehicles built on or before 14-Nov-2018 equipped with a power liftgate may exhibit a discharged battery, interior lamps cycling on and off erratically and/or a Liftgate Ajar message in the instrument panel cluster (IPC) when the liftgate/doors are shut. This may be due to the calibration of the rear gate trunk module (RGTM) keeping the module awake. Reprogram the RGTM using the latest software level of the appropriate Ford diagnostic scan tool.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019 Edge/Nautilus vehicles equipped with a 8F57 transmission and built on or before 01-Mar-2019 may exhibit harsh/bumpy upshift, downshift and/or engagement concerns. This may be due to various powertrain control module (PCM) software parameters for upshift flares, stationary and rolling engagements, and coasting downshift bumps. To resolve the condition, reprogram the PCM. Follow the Service Procedure steps to correct the condition on vehicles that meet all the following criteria: 2019 Edge/Nautilus 8F57 transmission Built on or before 01-Mar-2019 Harsh/bumpy upshift, downshift and/or engagement concerns
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019 Edge/Nautilus vehicles built on or before 07-Mar-2019 may exhibit an inoperative power liftgate with diagnostic trouble code (DTC) B144F:79 stored in the rear gate trunk module (RGTM). This may be due to the calibration of the RGTM. To resolve the concern, reprogram the RGTM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming use causal part number 14B291 and Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: ELECTRICAL SYSTEM · STRUCTURE:BODY:HATCHBACK/LIFTGATE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2019 F-Super Duty, 2017-2019 Continental, 2016-2019 Edge, 2016-2018 MKX, 2019 Nautilus vehicles may exhibit a U3000:49 diagnostic trouble code (DTC) setting in the Steering Effort Control Module (SECM) with no other DTCs present. To eliminate the DTC, perform the IDS SASM module reset routine. The IDS reset routine is available under Toolbox > Chassis > Steering > Adaptive Front Steering > SASM Module Reset. Do not attempt any repairs at this time. Engineering is investigating, monitor OASIS for updates. For claiming, use causal part 3600 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019 Mustang, Continental, Fusion, MKZ, F150, Transit Connect, Ranger, Edge or Nautilus with SYNC 3 may have the following intermittent symptoms: a solid blue screen when moving forward at speeds above 10 mph, the rear view camera remains on the screen at speeds below 10 mph, or inoperative infotainment applications. To resolve this concern, check for a SYNC software update under the OASIS Tab SYNC selection. If an update is available, update the APIM software per WSM section 415-00. After the complete pop-up appears, remove the USB flash drive and install it into the IDS tool to update the Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes, which is critical for a successful installation. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019 Mustang/Fusion/Edge/F-150/Continental/MKZ/Nautilus/Ranger vehicles with SYNC 3 may show a pop-up message every key cycle that states Network Connection Needed - To complete the system updates your vehicle should connect to a Wi-Fi network or through the FordPass/LincolnWay app. Until the update is completed, some features may not be available. Would you like to attempt to connect to a Wi-Fi network now? This message may occur, even if SYNC has been connected to a trusted Wi-Fi source. To temporarily remove the inconvenience of this pop-up message, advise the customer from SYNC to select Settings > Automatic Updates > System Wi-Fi and turn off System Wi-Fi, then turn off automatic system updates. Engineering is investigating, monitor OASIS for updates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2017 vehicles may experience a no crank concern due to a security access key table error. When attempting to program keys or perform a parameter reset, the procedure may fail and the Integrated Diagnostic System (IDS) scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the Body Control Module (BCM) is internally faulted and requires replacement. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2017 vehicles may experience a no crank concern due to a security access key table error. When attempting to program keys or perform a parameter reset, the procedure may fail and the Integrated Diagnostic System (IDS) scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the Body Control Module (BCM) is internally faulted and requires replacement. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019 Edge/Nautilus vehicles equipped with 2.0L EcoBoost engines may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P2282 stored in the powertrain control module (PCM). This concern may be due to an intermittent stuck open brake vacuum on demand valve causing an uncommanded high air flow intake manifold leak. Inspect the vacuum on demand valve (K2GC-2420-AD/K2GZ-2420-A). The Powertrain Controls and Emissions Diagnosis (PC/ED) Manual Pinpoint Test HG and Workshop Manual are being updated to include a diagnostic routine for the vacuum on demand valve and a procedure to remove and install the vacuum on demand valve. Engineering is investigating, monitor OASIS for updates.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE · SERVICE BRAKES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019 Edge/Nautilus vehicles equipped with a 2.0L EcoBoost engine, built on or before 23-Jan-2019 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P0128, P0217, P02EE, P02EF, P02F0, P02F1, P044C, P1285, P1299, and/or P2196 stored in the powertrain control module (PCM). This may be due to various settings in the PCM software. To resolve the condition, update the PCM software.
Source components: ELECTRICAL SYSTEM · POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019 Edge/Nautilus vehicles equipped with 2.0L EcoBoost engines may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P2282 stored in the powertrain control module (PCM). This concern may be due to an intermittent stuck open brake vacuum on demand valve causing an uncommanded high air flow intake manifold leak. Inspect the vacuum on demand valve (K2GC-2420-AD/K2GZ-2420-A). The Powertrain Controls and Emissions Diagnosis (PC/ED) Manual Pinpoint Test HG and Workshop Manual are being updated to include a diagnostic routine for the vacuum on demand valve and a procedure to remove and install the vacuum on demand valve. Engineering is investigating, monitor OASIS for updates.
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019 Edge/Nautilus vehicles equipped with a 2.0L EcoBoost engine, built on or before 23-Jan-2019 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P0128, P0217, P02EE, P02EF, P02F0, P02F1, P044C, P1285, P1299, and/or P2196 stored in the powertrain control module (PCM). This may be due to various settings in the PCM software. To resolve the condition, update the PCM software.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2019 Explorer, 2016-2018 MKX, 2019 Edge/Nautilus, 2017-2019 Fusion/MKZ, and 2018-2019 F-150/Mustang/Expedition/Navigator vehicles equipped with climate controlled seats may exhibit a buzzing noise from the front seats, front seats too warm, and/or inoperative climate controlled front seats. DTCs B14BA:13, B1154:4B, and/or B14B9:13 may also be present. This may be due to loose terminal pin fit on the driver seat module (DSM) connector C341D (16 pin). If a loose terminal pin fit condition is found during normal diagnostics per Workshop Manual (WSM), Section 501-10, a new service pigtail connector (part number 3U2Z-14S411-BRAB) is available. Refer to Wiring Diagram, Cell 119 to make sure C341D is a 16 pin connector and not a 20 pin connector. Refer to Wiring Diagram, Cell 5 for the recommended splicing procedures.
Source components: ELECTRICAL SYSTEM · SEATS · SEATS:FRONT ASSEMBLY:SEAT HEATER/COOLER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2019 Explorer, 2016-2018 MKX, 2019 Edge/Nautilus, 2017-2019 Fusion/MKZ, and 2018-2019 F-150/Mustang/Expedition/Navigator vehicles equipped with climate controlled seats may exhibit a buzzing noise from the front seats, front seats too warm, and/or inoperative climate controlled front seats. DTCs B14BA:13, B1154:4B, and/or B14B9:13 may also be present. This may be due to loose terminal pin fit on the driver seat module (DSM) connector C341D (16 pin). If a loose terminal pin fit condition is found during normal diagnostics per Workshop Manual (WSM), Section 501-10, a new service pigtail connector (part number 3U2Z-14S411-BRAB) is available. Refer to Wiring Diagram, Cell 119 to make sure C341D is a 16 pin connector and not a 20 pin connector. Refer to Wiring Diagram, Cell 5 for the recommended splicing procedures.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019 Edge Equipped With Adaptive Headlamps (High Series lamp - Titanium (301A) and ST (401A)) may be reported that the front headlamp lights are not bending while the vehicle is moving through a curve at speeds above 5 kph (3 mph), or that the system check outlined in the owner guide for this feature indicates the feature is not working correctly. Engineering is aware of this issue and is working on a repair solution. The headlamps will continue to function to fully meet all applicable lighting requirements. Do not attempt any diagnosis or repairs for this issue. Continue to monitor OASIS for updates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019 Edge Equipped With Adaptive Headlamps (High Series lamp - Titanium (301A) and ST (401A)) may be reported that the front headlamp lights are not bending while the vehicle is moving through a curve at speeds above 5 kph (3 mph), or that the system check outlined in the owner guide for this feature indicates the feature is not working correctly. Engineering is aware of this issue and is working on a repair solution. The headlamps will continue to function to fully meet all applicable lighting requirements. Do not attempt any diagnosis or repairs for this issue. Continue to monitor OASIS for updates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2019 F150/Edge, 2016-2018 MKX, 2019 Nautilus and 2017-2019 Fusion/Continental vehicles equipped with a 2.7L engine may exhibit a malfunction indicator lamp (MIL) and/or wrench lamp with diagnostic trouble codes (DTCs) P0116, P0117, P0118, P0119, P0217, P0330, P1026, and/or P130D. This may be due to a engine coolant temperature (ECT) sensor connector which is not fully seated or damaged wiring between connectors C1064 and C1047 for F150 and C1016 and C1168 for Edge/MKX/Nautilus/Fusion/Continental vehicles. ECT sensors should not be replaced if damaged wiring is found at or near these connectors. For claiming, use causal part 12A699 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING:COOLING SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2019 F150/Edge, 2016-2018 MKX, 2019 Nautilus and 2017-2019 Fusion/Continental vehicles equipped with a 2.7L engine may exhibit a malfunction indicator lamp (MIL) and/or wrench lamp with diagnostic trouble codes (DTCs) P0116, P0117, P0118, P0119, P0217, P0330, P1026, and/or P130D. This may be due to a engine coolant temperature (ECT) sensor connector which is not fully seated or damaged wiring between connectors C1064 and C1047 for F150 and C1016 and C1168 for Edge/MKX/Nautilus/Fusion/Continental vehicles. ECT sensors should not be replaced if damaged wiring is found at or near these connectors. For claiming, use causal part 12A699 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019 Mustang/Fusion/Edge/F-150/Continental/MKZ/Nautilus with SYNC 3 may show a pop-up message every key cycle that states Network Connection Needed - To complete the system updates your vehicle should connect to a Wi-Fi network or through the FordPass/LincolnWay app. Until the update is completed, some features may not be available. Would you like to attempt to connect to a Wi-Fi network now? This message may occur, even if SYNC has been connected to a trusted Wi-Fi source. To temporarily remove the inconvenience of this pop-up message, advise the customer from SYNC to select Settings > Automatic Updates > System Wi-Fi and turn off System Wi-Fi, then turn off automatic system updates. Engineering is investigating, monitor OASIS for updates
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2012-2019 Vehicles may require repairs to the Smartlink system. Smartlink is a Ford Licensed Accessory which has a warranty provided by the accessory manufacturer. Warranty replacement parts for Smartlink that are ordered through Ford are not reimbursable through the Ford Motor Company warranty system. Please see the Warranty and Policy Manual for further information on Ford Licensed Accessories.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019 Mustang, Continental, Fusion, MKZ, F150, Edge or Nautilus with SYNC 3 may have a symptom of a rear view camera that remain on the screen when moving forward above 5MPH or a solid blue screen once the vehicle is at cruising speed. Some vehicles may experience inoperative infotainment applications such as Apple CarPlay. To eliminate these symptoms from occurring, it is recommended to disable the Wi-Fi in the settings menu by selecting Automatic updates. Shut off system WIFI and then disable automatic updates. If the vehicle is stuck in the rear camera state you can exit this state by shutting the vehicle off and powering the system down for at least three minutes. Engineering is investigating, monitor OASIS for updates.
Source components: BACK OVER PREVENTION · BACK OVER PREVENTION: SENSING SYSTEM: CAMERA.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2015-2019 Edge, 2016-2018 MKX, and 2019 Nautilus vehicles equipped with all wheel drive (AWD) may exhibit a fuel slosh noise primarily when the fuel tank is over 3/4 full and when driving at low speeds. This may be due to the fuel moving around in the fuel tank. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2016-2019 Ford and Lincoln vehicles equipped with SYNC 3 and a 6, 8 or 10 inch screen may show a pop-up message every key cycle that states 'SYNC can check for updates when connected to a WiFi network'. To remove the inconvenience of the pop-up the customer can either connect to a trusted WiFi network to complete the setup process or turn off WiFi in the WiFi settings located under the Settings menu. Adjusting the setting for the customer is not a warrantable defect.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019 Mustang, Continental, Fusion, MKZ, F150, Edge or MKX with SYNC 3 may have a symptom of a rear view camera that remain on the screen when moving forward above 5MPH or a solid blue screen once the vehicle is at cruising speed. To eliminate this symptom from occurring, it is recommended to disable the Wi-Fi in the settings menu by selecting Automatic updates. Shut off system WIFI and then disable automatic updates. If the vehicle is stuck in the rear camera state you can exit this state by shutting the vehicle off and powering the system down for at least three minutes. Engineering is investigating, monitor OASIS for updates.
Source components: BACK OVER PREVENTION: SENSING SYSTEM: CAMERA · ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2013-2018 C-Max, 2013-2019 Escape/Fusion/MKZ, 2015-2018 Focus, 2015-2019 Edge/F150/MKC/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017 Super Duty, 2018-2019 EcoSport/Expedition, and 2019 Nautilus vehicles may experience seat pan looseness, lateral movement, or clunk/thump noise on turns. Follow the Service Procedure steps to correct the condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019 Focus/Transit Connect/Edge/Nautilus vehicles equipped with 8F35 transmission may exhibit an appearance of a fluid leak or weep from transmission axle shaft seal. This condition may be caused by excessive internal seal (dark brown) grease lubricant that is applied during manufacturing of the axle seals. With a suitable cloth, clean the grease from the transmission seal and housing with Motorcraftù Metal Brake Parts Cleaner or equivalent. If the fluid is red, refer to Workshop Manual (WSM), Section 307-01 for normal diagnostics.
NHTSA source summary · Original PDF not reviewed by Recallfolio
For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. For all turbocharged engine applications, the turbocharger oil supply filter (6C683 gas engine/6L625 connector style or 6A968 diesel engine) must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.
Source components: ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER.