2022 Ford BRONCO SPORT Manufacturer communications & TSBs.Page 2
Original record summaries, dates and identifiers for this model-year. Records 101–150 of 150, ordered newest first. Dated records on this page: Nov 23, 2021–Apr 4, 2023.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Apr 4, 2023Service Bulletin/Repair Instructions
SSM 51536
NHTSA communication ID: 10235153
NHTSA source summary · Original PDF not reviewed by Recallfolio
For 2000-2024 Ford and Lincoln vehicles, swapping a module from a vehicle for diagnosis purposes is likely to cause errors and is not recommended. It is also not recommended to order a replacement module using a vehicle identification number (VIN) from a different vehicle. Most modules on these affected vehicles are VIN/vehicle specific and hardware variations between modules do exist. Swapping a module from a vehicle or ordering a module using a different vehicle/VIN can cause ineffective repairs and additional vehicle down time. Make sure all appropriate Workshop Manual (WSM) procedures are followed when diagnosing the condition prior to all module replacements and only order modules using the correct VIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2023 Bronco Sport vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P025A, P025B, P00C6, P008A, P0627 and/or U0109 stored in the powertrain control module (PCM). This may be due to an intermittent or partial disconnect of the harness, connector pin push-outs or loose/corroded grounds to the fuel pump control module (FPCM) connector, PCM connector and/or battery junction box connector. Inspect the following connectors for 1.5L and 2.0L engines: C1551B, C1035A, C110, C401, C4033, C4330. Verify the connections are fully seated, without damage and/or pushed out pins/terminals prior to performing Workshop Manual (WSM) diagnostics or replacing any components. Inspect G404 and verify it's clean and secure. If any connector damage is found, repair as necessary. Refer to Wiring Diagram, Cell 005.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Escape/Corsair, 2021-2022 Bronco Sport, and 2022 Maverick vehicles built on or before 23-Mar-2022 may exhibit a hard, stiff, and/or difficult to turn condition due to a lack of power steering assist during engine start-up with U3000 diagnostic trouble codes (DTCs) stored in the PSCM. Using the latest version of Ford Diagnosis and Repair System (FDRS) tool, select and run the PSCM - Reset the Power Steering Control Module (PSCM) application. After PSCM reset, perform an ignition cycle. Update the PSCM to the latest software level using FDRS tool. If the U3000 DTC returns, continue with diagnostics and repair direction using Workshop Manual (WSM), Section 211-02 > Power Steering > Diagnosis and Testing. For claiming, use causal part 3C529 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2021-2023 Model Year Bronco Sport and 2020-2022 Model Year Escape Vehicles with a 3-cylinder 1.5L Engine Replacement of High-Pressure Fuel Injectors
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Escape/Corsair, 2021-2022 Bronco Sport, 2022 Maverick vehicles built on or before 23-Mar-2022 may exhibit driver assistance warning messages displayed in the instrument panel cluster (IPC): Pre-collision Assist Not Available, Cruise Control Not Available, Collision Warning Malfunction and/or Adaptive Cruise Control Malfunction. Diagnostic trouble code (DTC) U0415:00 may also be stored in the power steering control module (PSCM), DTC C0051:67 stored in the anti-lock brake system (ABS) module and DTC U0418:86 stored in the image processing module A (IPMA). This may be due to the software in the PSCM. Using the latest version of Ford Diagnosis and Repair System (FDRS) scan tool, update the PSCM to the latest software level. For claiming, use causal part 3C529 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
2020-2022 Model Year Escape and Corsair, 2021-2022 Bronco Sport and 2022 Maverick Vehicles Equipped With a 2.0L EcoBoost Engine Vehicle Emissions Control Information Label Update Owner Letters
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL · EQUIPMENT:OTHER:LABELS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Escape vehicles built on 1-Nov-2020 and through 29-Aug-2022 and 2021-2022 Bronco Sport vehicles built on or before 23-Sep-2022 may exhibit a moan noise when the vehicle is driven in reverse (R) in cold weather and/or high humidity. This may be due to the suspension sensitivity of the vehicle and interaction of the caliper housing with the pad backplate. To correct this condition, follow the Service Procedure to replace the rear caliper bushings.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2020-2022 Model Year Escape and Corsair, 2021-2022 Bronco Sport and 2022 Maverick Vehicles Equipped With a 2.0L EcoBoost Engine Vehicle Emissions Control Information Label Update
NHTSA source summary · Original PDF not reviewed by Recallfolio
Certain 2022 Model Year Multiple Vehicle Lines Equipped with 8F35 Transmissions Transmission Replacement In all of the affected vehicles, the snap ring that is used to hold the 8F35 transmission clutch compression spring engaged was not fully seated in the assembly process. When the snap ring is not fully seated, the transmission will function as if the C clutch is partially engaged. The customer may experience rough shifts until the transmission can adapt to the clutch performance. There is a potential long term durability concern associated with the compromised function of the clutch.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Bronco Sport vehicles built on or before 07-Nov-2022 may exhibit a squeak/rattle/creak noise from the roof opening panel when the glass is closed or in vent position while driving on uneven highways. This may be due to roof opening panel bolts not being properly secured. To correct this condition, confirm that the bolts on each side of the moon roof are properly tightened. If the bolts are not properly tightened, tighten the bolts. Refer to the Workshop Manual Section (WSM), Section 501-17 Roof Opening Panel Glass > Removal and Installation.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Escape/Corsair, 2021-2022 Bronco Sport, 2022 Maverick vehicles may exhibit any of the following driver assistance warning messages displayed in the instrument panel cluster (IPC): Pre-collision Assist Not Available, Cruise Control Not Available, Collision Warning Malfunction and/or Adaptive Cruise Control Malfunction. Diagnostic trouble code (DTC) U0415:00 may also be stored in the power steering control module (PSCM), DTC C0051:67 stored in the anti-lock brake system (ABS) module and DTC U0418:86 stored in the image processing module A (IPMA). This may be due to the software in the power steering control module (PSCM). To correct this condition, using the latest version of Ford Diagnosis and Repair System (FDRS) scan tool. Update the PSCM to the latest software level.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 22-2176 to increase the labor operation allowance and update the part list. Some 2020-2022 Escape/Corsair vehicles built on or before 3-Jan-2022, 2020-2022 Explorer vehicles built on or before 14-Feb-2022, 2020-2022 Aviator vehicles built on or before 07-Feb-2022 and 2021-2022 Bronco Sport vehicles built on or before 3-Dec-2021 may exhibit a slow fuel fill and/or spit back condition during refueling. This may be due to the design of the fuel tank filler pipe. To correct the condition, follow the Service Procedure to replace the fuel tank filler pipe.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Escape/Corsair, 2021-2022 Bronco Sport, and 2022 Maverick vehicles may exhibit a hard, stiff, and/or difficult to turn condition due to a lack of power steering assist during engine start-up with various U3000 diagnostic trouble codes (DTCs) and/or U3000:66. To correct this condition, using the latest version of Ford Diagnosis and Repair System (FDRS) tool, select and run the PSCM - Reset the Power Steering Control Module (PSCM) application. After PSCM reset, perform an ignition cycle. Update the PSCM to the latest software level using (FDRS) tool. If DTCs U3000 returns, continue with diagnostics and repair direction using Workshop Manual (WSM), Section 211-02 > Power Steering > Diagnosis and Testing. For claiming, use causal part 3C529 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: POWER TRAIN · STEERING:STEERING CONTROL MODULE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Escape/Corsair/F-53 Motorhome/F-59 Commercial Stripped Chassis, 2021-2023 F-650/F-750/E-Series, and 2021-2022 Bronco Sport vehicles may exhibit an intermittent no crank/no start condition and/or an intermittent blank instrument panel cluster (IPC)/SYNC touchscreen. This may be due to the software in the gateway module (GWM). To correct the condition, reprogram the GWM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming use causal part 14F642 and the applicable labor operations of Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: BACK OVER PREVENTION:SOFTWARE · ENGINE AND ENGINE COOLING:ENGINE:CRANK/CAMSHAFT POSITION SENSOR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2021 Expedition/Navigator, 2020-2022 F Super Duty/Explorer, 2021-2022 Bronco/Corsair/Escape/Bronco Sport, 2022 Maverick vehicles may exhibit the wireless charger inoperative or poor performance when using some Apple iPhone models that use MagSafe wireless charging including iPhone 12 and 13. This may be due to limited compatibility with the wireless accessory charging module (WACM). To correct the condition, follow the Service Procedure to update the WACM. Note: The WACM software is designed to improve the compatibility between some Apple MagSafe charging iPhones, including iPhone 12 and 13 models, and the Ford Qi wireless charging module.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022 Bronco Sport vehicles built on 04-Aug-2022 and through 05-Aug-2022 may exhibit an ABS warning indicator with diagnostic trouble code (DTC) C0030:07 stored in the ABS module. The vehicle may also exhibit a squeal noise from the left front wheel area. This may be due to a condition where the wheel bearing and snap ring are not fully seated in the left wheel knuckle causing contact between the front halfshaft and wheel knuckle. To correct this condition, follow the Service Procedure to diagnose and replace the wheel knuckle, hub, bearing and front halfshaft.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2023 Ford and Lincoln vehicles equipped with a telematic control unit (TCU) may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization, and/or modem electronic serial number (ESN) could not be displayed in the center display screen. To correct this condition prior to programming, remove the TCU fuse for 5-minutes then reinstall. Delete all previous session files for the vehicle. Start a new Ford Diagnosis and Repair System (FDRS) session. Perform a TCU provisioning and Program the TCU to the latest FDRS version level. If the concern is still present, follow normal diagnostics in Workshop Manual (WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Mustang Mach-E built on or before 17-Jan-2022, 2022 Escape built on or before 03-Mar-2022, Bronco Sport built on or before 04-Mar-2022, 2022 Maverick built on or before 25-Jan-2022 and 2022 Transit built on or before 17-May-2022 may exhibit a powertrain malfunction (wrench) indicator with diagnostic trouble code (DTC) P0929:77 stored in the gear shift module (GSM). This may be due to the software in the GSM. To correct this condition, perform Pinpoint Test D. Refer to Workshop Manual (WSM), Section 307-05 > Diagnosis and Testing. If the GSM is not operating correctly, perform the replacement of the GSM. Do not perform a PMI after installing a new GSM assembly. The GSM is shipped with the latest software level. For claiming, use causal part 7P155 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Escape/Corsair vehicles built on or before 17-May-2022 and 2021-2022 Bronco Sport vehicles built on or before 25-Feb-2022 may exhibit a hiss or rattle noise while driving. This may be due to an internal issue with the manual park release cable. If the noise is eliminated when the cable is disconnected from the transmission, install a new manual park release cable assembly LX6Z-7D246-T. Refer to the Workshop Manual (WSM), Section 307-05 > Automatic Transmission External Controls > Removal and Installation.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Escape vehicles built on 01-Oct-2020 and through 21-Jul-2022 and equipped with 1.5L engine and vacuum booster and 2021-2022 Bronco Sport vehicles built on or before 2-Dec-2021 may exhibit a squeal noise from the front brakes when applied at low or high speed. The alternate front brake disc (standard version) improves high frequency noise performance. To correct this condition, follow the Service Procedure to perform the replacement of the front brake discs.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Ford and Lincoln vehicles equipped with a telematic control unit (TCU) may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization, and/or modem electronic serial number (ESN) could not be displayed in the center display screen. To correct this condition prior to programming, remove the TCU fuse for 5-minutes then reinstall. Delete all previous session files for the vehicle. Start a new Ford Diagnosis and Repair System (FDRS) session. Perform a TCU provisioning and Program the TCU to the latest FDRS version level. If the concern is still present, follow normal diagnostics in Workshop Manual (WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: COMMUNICATION:MANUFACTURER TELEMATICS · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Bronco Sport vehicles may exhibit a rattle or flapping noise coming from the rear air duct vents while driving. This may be due to the normal operation of the rear air duct vents. To determine if this is a normal condition, perform a road test at 40 MPH (65 Km/h) or above. Inspect if the noise is coming from the rear vents. During the road test alternate air conditioning (A/C) between fresh mode and air re-circulation mode. If the noise is eliminated when the A/C is in fresh mode, this is considered a normal characteristic of the vehicle and no repairs should be performed.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022 Escape and Bronco Sport vehicles equipped with 1.5L engines should not be taken out of transport mode before customer delivery to reduce the risk of driving performance issues such as: rough operation, idle quality, engine misfires, lack or loss of engine power. These conditions may occur due to carbon fouled spark plugs from repeated engine ignition starts without driving the vehicle to normal operation temperatures (82°C to 97°C) during cold weather. Make sure that the vehicles in stock are in transport mode. Refer to the Workshop Manual (WSM), Section 419-10 Malfunction Electronic Modules > General Procedures.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Mustang Mach-E vehicles built on 01-Aug-2021 and through 18-Jan-2022, 2022 Maverick vehicles built on 13-Sep-2021 and through 18-Jan-2022, 2022 Escape vehicles built on 24-Sep-2021 and through 18-Jan-2022, 2022 Bronco Sport vehicles built on 08-Nov-2021 and through 18-Jan-2022 may exhibit a shift knob can be rotated without stepping on the brake pedal, although the transmission remains in park (P). This condition may be intermittent, more noticeable in warmer temperatures. DTC P0929 may also be set in the gear shift module (GSM). This may be due to a GSM concern. To correct the condition, follow the Service Procedure to update the GSM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Mustang Mach-E, 2022 Escape/Bronco Sport/Maverick/Transit vehicles may exhibit a powertrain malfunction (wrench) indicator with diagnostic trouble code (DTC) P0929:77 stored in the gear shift module (GSM). This may be due to the software in the GSM. To correct this condition, reprogram the GSM module using the latest software level of the Ford Diagnosis and Repair System (FDRS). For claiming, use causal part 7P155 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Bronco Sport vehicles equipped with 2.0L engine may exhibit a malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P0036 and/or P0138 stored in the powertrain control module (PCM). This may be due to corrosion or water intrusion in connector C201 and/or C1570. Prior to performing Workshop Manual (WSM) diagnostics, inspect the male and female side of connector C201 and C1570 for signs of corrosion or water intrusion. If corrosion or water intrusion is found, replace connector C201 and/or C1570 with a pigtail kit and apply Motorcraftî Electrical Grease (XG-12) or equivalent.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Escape and 2022 Bronco Sport vehicles may exhibit a moan noise when the vehicle is driven in reverse (R) in cold weather and/or high humidity. This may be due to the suspension sensitivity of the vehicle. To correct this condition, follow the Service Procedure to replace the rear caliper bushings.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2022 Ford and Lincoln vehicles equipped with the 8F35 transmission built on or before 16-Mar-2022 may exhibit transmission slip during acceleration from a stop when hot. This may be due damaged internal case half pump seals (7N265). To correct the condition, remove the transmission and replace the internal case half pump seals. Refer to Workshop Manual (WSM), Section 307-01.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2022 Ford/Lincoln customers may experience a notification in the FordPassÃÂÃÂÃÂî/LincolnWayÃÂÃÂÃÂî app indicating Vehicle Has Entered Deep Sleep Mode. This occurs when the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SOC) drops below 50%. A warning may also set if the telematic control unit (TCU) has received an over the air update. The TCU powers down all communication when in this mode and app features are disabled. Manually start the vehicle to wake if from mode. More information is located in the app under: Account > Help > search 'Deep Sleep' in the entry box. If the condition remains, check the BCM 12v SOC. If the SOC does not change after charging the battery or after BMS reset is performed, continue with normal battery and/or BMS sensor diagnostics.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Escape/Corsair/F-53 Motorhome/F-59 Commercial Stripped Chassis, 2021-2023 F-650/F-750/E-Series, and 2021-2022 Bronco Sport vehicles may exhibit a communication fault with emissions inspection equipment. This may be due to the software in the gateway module (GWM). To correct this condition, reprogram the GWM to latest software level using the appropriate Ford diagnostic scan tool. Use causal part 14F642 and applicable labor times from Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: ELECTRICAL SYSTEM:SOFTWARE · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL · EQUIPMENT.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Escape/Corsair, 2021-2022 Bronco Sport and 2022 Maverick vehicles may exhibit a condition where the door(s) do not open using the exterior door handle(s). This may be due to an enabled permanent engagement inertia lock within the exterior door handle, this condition occurs when the doors are closed or opened with excessive force. To correct this condition, follow the Service Procedure to properly disengage the permanent engagement inertia lock clip to allow the exterior door handle(s) to fully extend and open the door(s) from the outside.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022 Escape and Bronco Sport vehicles may exhibit a powertrain malfunction (wrench) indicator with diagnostic trouble code (DTC) P0929:77 stored in the gear shift module (GSM). This may be due to the software in the GSM. To correct this condition, reprogram the GSM module using the latest software level of the Ford Diagnosis and Repair System (FDRS). For claiming, use causal part 7P155 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: BACK OVER PREVENTION:SOFTWARE · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2017-2022 Ford and Lincoln vehicle owners may experience a condition of missing authorization, command and control, battery charging details or phone-as-a-key setup buttons/selections in their FordPass or LincolnWay App. This condition is due to an error within the FordPass or LincolnWay App and not due to a concern on the vehicle. Verify that the customers FordPass or LincolnWay App is at the latest version. Replacement or reprogramming of the telematics control unit (TCU)/gateway module (GWM)/remote function actuator (RFA) will not resolve this condition. If the condition persists, utilize the FordPass Guides or Lincoln Way Concierge teams.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Escape/Corsair vehicles built on or before 3-Jan-2022, 2020-2022 Explorer vehicles built on or before 14-Feb-2022, 2020-2022 Aviator vehicles built on or before 07-Feb-2022 and 2021-2022 Bronco Sport vehicles built on or before 3-Dec-2021 may exhibit a slow fuel fill and/or spit back condition during refueling. This may be due to the design of the fuel tank filler pipe. To correct the condition, follow the Service Procedure to replace the fuel tank filler pipe.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Bronco Sport vehicles equipped with a 1.5L engine may exhibit coolant stains on the A/C compressor. If coolant stains are observed on the A/C compressor, inspect the A/C system for leaks. Refer to the Workshop Manual, Section 412-00 Climate Control System > General Information > A/C Compressor Leak Detection to ensure proper function. If no performance issues are identified, do not replace the A/C compressor for this condition.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Escape/Corsair, 2021-2022 Bronco Sport, 2022 Maverick vehicles may exhibit any of the following driver assistance warning messages displayed in the instrument panel cluster (IPC): Pre-collision Assist Not Available, Cruise Control Not Available, Collision Warning Malfunction and/or Adaptive Cruise Control Malfunction. Diagnostic trouble code (DTC) U0415:00 may also be stored in the power steering control module (PSCM), DTC C0051:67 stored in the anti-lock brake system (ABS) module and DTC U0418:86 stored in the image processing module A (IPMA). This may be due to the software in the power steering control module (PSCM). To correct this condition, using the latest version of Ford Diagnosis and Repair System (FDRS) scan tool. Update the PSCM to the latest software level.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Bronco Sport vehicles built on or before 22-Feb-2022 may exhibit a hiss or rattle noise while driving. This may be due to an internal issue with the manual park release cable. If the noise is eliminated when the cable is disconnected from the transmission, install a new manual park release cable assembly. Refer to the Workshop Manual (WSM), Section 307-05 > Automatic Transmission External Controls > Removal and Installation.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021 and 2022 Ford and Lincoln vehicles may experience a tire sidewall wavy/indentation appearance in the radial direction on one or both sidewalls. Sidewall wavy/indentation appearance is a common cosmetic characteristic of radial tire construction and will not affect the performance of the tire.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Escape/Corsair, 2021-2022 Bronco Sport, 2022 Maverick vehicles equipped with 4-wheel drive (4WD) may exhibit a grinding/rubbing noise from floor pan/underbody area. This noise will be most noticeable on tip in acceleration and may be due to a mispositioned fuel tank heat shield. To correct the condition, follow the Service Procedure to reposition the fuel tank heat shield.
NHTSA source summary · Original PDF not reviewed by Recallfolio
In various 2017-2022 Ford and Lincoln vehicles, customers may receive a message in the FordPass or LincolnWay App stating "Feature Unavailable. Since this is a fleet vehicle, it cannot access the (SYNC Connect) FordPass or LincolnWay app through the TCU Embedded Modem. If this message appears, the vehicle may be equipped with a fleet telematics module. Replacement of the TCU or TCU related repairs will not prevent this message from appearing. Please refer the customer to in app FordPass Guides or LincolnWay Concierge Teams to aid with fleet telematics removal. Open app, select Account > Help > CHAT or CALL option
NHTSA source summary · Original PDF not reviewed by Recallfolio
This article supersedes TSB 21-2236 to update the models and year affected. Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2013-2022 Escape, 2015-2018 Focus, 2015-2019 MKC, 2015-2022 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2022 F-Super Duty, 2018-2022 EcoSport/Expedition, 2019-2022 Ranger/Nautilus, 2021-2022 Bronco/Bronco Sport/Mustang Mach-E, 2022 Maverick vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2022 Ford and Lincoln vehicles may need to perform A/C leak detection diagnostics. The 2022 Workshop Manual (WSM), Section 412-00 for A/C leak detection diagnosis is incomplete and is in the process of being updated. At this time, Pinpoint Test AN of Section 412-00 in the 2022 F-150 WSM can be used temporarily for the service procedure and specifications. Use the correct vehicle specific removal and replacement sections as needed. A new labor operation 19700A45 has also been released to align with the new procedure.
Source components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2019-2022 Edge/Nautilus, 2020-2022 Escape/Corsair, and 2021-2022 Bronco Sport vehicles equipped with a 2.0L EcoBoost or 2.3L EcoBoost may exhibit a lack of power with an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P02AB, P0243, P0299, P25B3, P25B4, P2AB7, P2AB8 and/or P2AB9. This may be due to an inoperative wastegate actuator, missing wastegate actuator e-clip or non-visible damage to the actuator rod. If the diagnostic procedures lead to replacement of the turbocharger assembly, note that a lower level service component has been released K2GZ-9G488-B for Edge/Nautilus/Escape/Corsair/Bronco Sport for service to replace the actuator, actuator rod and both e-clips instead of a complete turbocharger assembly. When replacing the wastegate actuator, it is required to replace all parts included in the service kit.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2021 Explorer/Aviator/Escape/Corsair, 2021-2022 Bronco Sport, and 2022 Maverick vehicles may exhibit an inoperative driver door window control switch (windows inoperative, mirror control unresponsive, etc.). Diagnostic trouble code (DTC) B1088:87 may be present in the driver door module (DDM). This may be due to the software in the DDM. To correct the condition, reprogram the DDM with the latest software level of the Ford Diagnosis and Repair System (FDRS). After reprogramming the DDM, run the DDM configuration application and perform a window learn routine via FDRS. For claiming, use causal part 14B291 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Source components: ELECTRICAL SYSTEM · ELECTRICAL SYSTEM:WIRING:SWITCHES/KNOBS/BUTTONS · STRUCTURE:BODY · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 Bronco Sport vehicles equipped with passive entry system may experience a condition where the liftgate passive entry feature is inoperative. This may occur if the user inadvertently presses the liftgate button on the passive key fob once and then presses the exterior liftgate release switch, causing the liftgate passive entry feature to become inoperative. To correct this condition, press the liftgate button twice on the passive key fob to restore the liftgate passive entry feature functionality.
Source components: STRUCTURE:BODY:HATCHBACK/LIFTGATE:SUPPORT DEVICE/STRUT · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2021-2022 F-150 and Bronco vehicles built with SYNC 4 require a connected phone with Android Auto or Apple CarPlay active to enable voice interactions and use of the steering wheel Voice Control button. This is due to the affected vehicles not having built in voice interactions capability. Vehicles with built in voice interactions capability can be identified as also being equipped with the built in Connected Navigation feature which includes a navigation tab on the touchscreen. Diagnostics should only be performed for voice interactions on vehicles equipped with built in voice interaction capability or with Android Auto or Apple CarPlay active.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2020-2022 Escape, 2021-2022 Bronco Sport and 2022 Maverick vehicles may require servicing of the interior door handle lock cable mounting bracket on the interior door handle. The interior door handle cable mounting bracket, part number right hand LJ6Z-78431B14-A and left hand LJ6Z-78431B15-A are now available to service separately from the cables and latch mechanisms. It is no longer necessary to replace the complete latch assembly for a damaged interior door handle lock indicator mounting bracket.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Some 2018-2021 EcoSport, Expedition, Navigator; 2019-2021 Ranger; 2020-2021 Escape, Corsair, Explorer, Transit; 2021 Bronco, Bronco Sport, Edge, Nautilus, F-150, Mustang; 2019-2022 Transit Connect; 2020-2022 Aviator, F-Super Duty; and 2022 Maverick vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0496, P0456, P0455, P04F0, and/or P0451. Ford has tested returned EVAP canister purge valves and found them to be fully functional. Prior to replacing the canister purge valve or other EVAP components, perform the following tests using the Ford Diagnosis and Repair System (FDRS) Scan Tool: Full System EVAP Leak Test - FDRS Location: TOOLBOX > PCM > PCM - Evap Emissions System Test and the EVAP Purge Valve Leak Test - FDRS Location: TOOLBOX > PCM > Evap Emission System Toolbox > CPV Check.