Original record summaries, dates and identifiers for this model-year. Records 201–282 of 282, ordered newest first. Dated records on this page: Mar 20, 2013–Oct 11, 2019.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
Oct 11, 2019Service Bulletin/Repair Instructions
9004144
NHTSA communication ID: 10168382
NHTSA source summary · Original PDF not reviewed by Recallfolio
RADIO, MULTI Media For RA3 and RA4 8.4? radio concern of reoccurring update request pop-up on each key cycle after a radio FOTA (Firmware Update Over the Air) has been completed, please DO NOT replace the radio. To recover the radio, 12v power needs to be disconnect from the radio to clear radio memory either by removal of the radio fuse or preforming a battery disconnect. Note: Fuse removal is the preferred method. The radio needs to be disconnected from power long enough to clear memory and discharge the Capacitance within the radio. Please refer to the latest in diagnostics for further information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash Over The Air (FOTA) Software Update RA3 and RA4 Radio This bulletin provides information regarding the latest Flash Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Pentastar Upgrade Oil Fill Level after an Oil Change This bulletin involves rechecking the oil fill level after filling the engine to the correct specifications. The customer may describe that after an oil change they check their oil fill level and it is showing overfilled on the oil dipstick.
NHTSA source summary · Original PDF not reviewed by Recallfolio
RADIO [RES] - New and/or Service Exchange For RES radio concerns. Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
ACTUATOR, A/C and Heater Before replacing HVAC actuator, please contact either Thomas Conway (248) 635-7090 or Paul Aquino (248) 854-4819. Engineering is looking to gather infomation on fail mode and customer concern. If no response in 15 minutes, proceed with repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
ROTOR, Brake For Grand Cherokee (WK) with BR2 or BR3 Sales Codes, you MUST replace both Front and Rear rotors. Order (2) 68035012A$ and order (2) 68035022A$ Durango (WD) only requires Front Rotors - order (2) 68240046A$
Source components: SERVICE BRAKES, HYDRAULIC · SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC:ROTOR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Motor, Windshield Wiper For Jeep Grand Cherokee, Dodge Durango, Chrysler 300, Dodge Charger, and Dodge Challenger that exhibit a non-functional Windshield Wiper Motor, replace the entire wiper module and contact FCA Current Production Quality at (248) 613-7591. If no response within 15 minutes, proceed with repair.
Source components: ELECTRICAL SYSTEM · VISIBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
A/C Pressure Transducer A/C inoperative and diagnosis leads to pressure transducer. Call Steve Rice at cell (248) 867-0061 before replacing the pressure transducer. If no response in 15 minutes, please proceed with repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Motor, Windshield Wiper For Jeep Grand Cherokee, Dodge Durango, Chrysler 300, Dodge Charger, and Dodge Challenger that exhibit a non-functional Windshield Wiper Motor, replace the entire wiper module and contact FCA Current Production Quality at (248) 613-7591. If no response within 15 minutes, proceed with repair.
Source components: ELECTRICAL SYSTEM · EQUIPMENT · VISIBILITY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
A/C Pressure Transducer A/C inoperative and diagnosis leads to pressure transducer. Call Steve Rice at cell (248) 867-0061 before replacing the pressure transducer. If no response in 15 minutes, please proceed with repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
RA3 and RA4 Radio Enhancements This bulletin involves inspecting and if required, updating the radio software. Customers may experience one or more of the following:Radio functions/touchscreen locks up (does not affect backup camera). Phone presets do not save. ?Navigation Failed? message is displayed. Navigation is inoperative or inaccurate. CD player will not play songs and/or locks up the radio. Clock will not automatically update to local time. Clock may be off by several hours. (RA3 only). Poor or no connection to cellular network. ?Charge Complete? notification is not received (RU PHEV only). Some Uconnect® App remote commands do not execute with the vehicle. Radio Apps are inoperative. Radio display screen is black or blank. Battery drain - due to radio staying on. Navigation failed message is displayed. Clock not automatically updating to local time. Improvements:Auto Play can now be configured. Media devices, Phone pairing and Bluetooth® usage improvements. Add the ability to drag and drop icons into the menu bar. Adds ?Do Not Disturb? text message feature. Fix for radio locks up/frozen. Enhanced Voice recognition (VR) performance. Improved tuner performance. Human Machine Interface (HMI) improvements. Satellite radio reception improvements.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Rear View Camera In the case for inoperative camera, radio screen is blue or black in reverse mode. Before proceeding with the normal procedure call Ali Ikram at (248) 576-9265 Mon- Fri between 8 am - 4pm. If you do not get a response within 15 minutes continue with the normal diagnostic procedure. Before replacing the camera, please disconnect and clean harness and camera connector. Clean & dry both connectors. If replacing the camera, please replace wire harness also and return parts to QEC.
Source components: BACK OVER PREVENTION: CAMERA SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Trans Oil Pan, Heater Tube or O-ring, Heater Applies to vehicles equipped with 8 speed transmissions only; If you have a leak that appears to be at the pan the use of proper leak detection is recommended. The fluid in the 8 speeds can be detected with a black light and there are aftermarket spray on leak detection materials to help ensure that the leak is properly diagnosed and not from another location such as cooler lines, heater tubes, or case porosity. If you have a leak concern please note that the transmission pan gasket is available for many of the 8 speed applications FCA offers. See your parts specialist for the proper gasket for the repair.
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
RA3 and RA4 Radio Enhancements This bulletin involves inspecting and if required, updating the radio software. Customers may experience one or more of the following:Radio functions/touchscreen locks up (does not affect backup camera). Phone presets do not save. ?Navigation Failed? message is displayed. Navigation is inoperative or inaccurate. CD player will not play songs and/or locks up the radio. Clock will not automatically update to local time. Clock may be off by several hours. (RA3 only). Poor or no connection to cellular network. ?Charge Complete? notification is not received (RU PHEV only). Some Uconnect® App remote commands do not execute with the vehicle. Radio Apps are inoperative. Radio display screen is black or blank. Battery drain - due to radio staying on. Navigation failed message is displayed. Clock not automatically updating to local time. Improvements:Auto Play can now be configured. Media devices, Phone pairing and Bluetooth® usage improvements. Add the ability to drag and drop icons into the menu bar. Adds ?Do Not Disturb? text message feature. Fix for radio locks up/frozen. Fix for radio loses time. Enhanced Voice recognition (VR) performance. Media devices, phone pairing and Bluetooth usage improvements. Improved tuner performance. Human Machine Interface (HMI) improvements. Satellite radio reception improvements.
Source components: BACK OVER PREVENTION:DISPLAY FUNCTION · EQUIPMENT:ELECTRICAL.
NHTSA source summary · Original PDF not reviewed by Recallfolio
RH and LH Exhaust Resonators If replacing resonator due to alignment issues between exhaust tips and rear fascia, please call the Design Release Engineer Spencer Hayes at cell (517) 215-0520 to review. If no response in 15 minutes, proceed with repair. Please take pictures of the issue and email to caitlin.feltner@fcagroup.com.
Source components: ENGINE AND ENGINE COOLING:EXHAUST SYSTEM · SUSPENSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Powertrain Diagnostic and System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one of the following DTCs have been set:P0556 - Brake Booster Pressure Sensor Circuit Performance. P040B - Exhaust Gas Recirculation Temperature Sensor 1 Circuit Performance(3.6L Only). U1424 - Implausible Engine Torque Signal Received(2017 MY Only). P2681 - Engine Coolant Bypass Valve Control Circuit Open(3.6L Only). P2299-00 - Brake Pedal Position/Accelerator Pedal Position Incompatible. B23C3 - Stop/Start Disable Switch 1/2 Correlation(3.0L and 3.6L Only). The following DTCs have been changed from a one trip fault to a two trip fault for(3.0L and 3.6L Only):P0335 - Crankshaft Position Sensor Circuit. P0339 - Crankshaft Position Sensor Intermittent. P0340 - Camshaft Position Sensor Circuit - Bank 1 Sensor 1. P0344 - Camshaft Position Sensor Intermittent - Bank 1 Sensor 1. P0365 - Camshaft Position Sensor Circuit - Bank 1 Sensor 2. P0369 - Camshaft Position Sensor Intermittent - Bank 1 Sensor 2. P0345 - Camshaft Position Sensor Circuit - Bank 2 Sensor 1. P0349 - Camshaft Position Sensor Intermittent - Bank 2 Sensor 1. P0390 - Camshaft Position Sensor Circuit - Bank 2 Sensor 2. P0394 - Camshaft Position Sensor Intermittent - Bank 2 Sensor 2. In addition, customers may experience one of the following conditions:A shorter auxiliary battery life. An illuminated Automatic Oil Change Indication (AOCI) light(3.6L Only). Other enhancements included in this update:Improvements to vehicle drivability during a cam or crank sensor MIL condition(2017 MY Only). Improved knock sensor performance.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Intake Manifold Gasket Intake Manifold Gaskets on Pentastar Upgrade (Sales Code ERC/ERF) are reusable provided they are not cut, torn or melted. The gaskets are not required by warranty to be replaced like they are on Pentastar Classic (ERB/EHB). The new gaskets are not interchangeable with Pentastar Classic Intake Manifold Gaskets.
Source components: ENGINE · ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
RA3 and RA4 Radio Over The Air Software Updates This bulletin provides information regarding the latest Flash Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The following improvements are included in this update:Fix for sport mode not working in the performance menu page (2015 LA equipped with 6.4L and 5.7L Sales Codes ESH and EZC Only). Adds Apple Siri® Eyes Free capability for iPhone® owners. Auto Play can now be configured. Adds do not disturb text message feature. The ability to drag and drop icons into the menu bar. Fix for radio locks up/frozen. Fix for stuck on black/blank screen. Human Machine Interface (HMI) improvements. Several navigation improvements. Fix for radio loss of time display. Media devices, phone pairing and Bluetooth usage improvements. Improved tuner performance. Enhanced Voice recognition (VR) performance. Enhancements in Connectivity Apps (Yelp, Pandora, Aha, etc).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Transmission Diagnostic and Shift Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) withthe latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technicianmay find the following Diagnostic Trouble Codes (DTC) set in the PCM memory:U0401-00 - Implausible Data Received From ECM/PCM (Sales Code ERC only). In addition some customers may experience one or more of the following condition:Poor shift quality on coast-down shifts (bumps) (Sales Code EZH only). During an engine limp mode condition, the transmission remains in a fixedgear. The following software enhancements are also available:Start Stop quality enhancement (WK with Sales Code ERC only). Transmission shift quality enhancement.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Water Pump, Idler Pulley If replacing the water pump or Idler Pulley for a chirp, squeal or NVH, please contact either: Ron Dallison cell: (248) 292-9510 ron.dallison@fcagroup.com Chris Riddick cell: (248) 434-3628 chris.riddick@fcagroup.com Joe Lovell cell: (734) 309-6467 joe.lovell@fcagroup.com Engineering is seeking audio recordings of the concern in an effort to root cause and make necessary improvements to future pumps. Please email any audio recording or documentation of when/where/how the pump, or Idler Pulley makes noise to the above emails. If the dealer is located in the Detroit Metro Area, Engineering may send a representative to review with technician. Any information is appreciated. If a response is not received within 15 mins , then proceed with the necessary repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Rear View Camera Before proceeding with the normal procedure call Ali Ikram at (248) 576-9265 Mon- Fri between 8 am - 4pm. If you do not get a response within 15 minutes continue with the repair. Make sure that connector is inserted properly. If there is a need to replace camera. In case of bad wire harness. Replace the harness and have it sent back to QEC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Amplifier Vehicles needing amplifier replacement, please call Rayyan Mohammed at Cell (248) 954-0790 prior to repair. If no response in 15 minutes, proceed with the repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Powertrain Diagnostic and System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one of the following DTCs have been set:P040B - Exhaust Gas Recirculation Temperature Sensor 1 Circuit Performance(2017 MY with a 3.6L Only). U1424 - Implausible Engine Torque Signal Received(2017 MY Only). P2681 - Engine Coolant Bypass Valve Control Circuit Open(3.6L Only). P2299-00 - Brake Pedal Position/Accelerator Pedal Position Incompatible. B23C3 - Stop/Start Disable Switch 1/2 Correlation(3.0L and 3.6L Only). The following DTCs have been changed from a one trip fault to a two trip fault for(3.0L and 3.6L 2017 MY Only):P0335 - Crankshaft Position Sensor Circuit. P0339 - Crankshaft Position Sensor Intermittent. P0340 - Camshaft Position Sensor Circuit - Bank 1 Sensor 1. P0344 - Camshaft Position Sensor Intermittent - Bank 1 Sensor 1. P0365 - Camshaft Position Sensor Circuit - Bank 1 Sensor 2. P0369 - Camshaft Position Sensor Intermittent - Bank 1 Sensor 2. P0345 - Camshaft Position Sensor Circuit - Bank 2 Sensor 1. P0349 - Camshaft Position Sensor Intermittent - Bank 2 Sensor 1. P0390 - Camshaft Position Sensor Circuit - Bank 2 Sensor 2. P0394 - Camshaft Position Sensor Intermittent - Bank 2 Sensor 2. In addition, customers may experience one of the following conditions:A shorter auxiliary battery life. An illuminated Automatic Oil Change Indication (AOCI) light(3.6L Only). Other enhancements included in this update:Improvements to vehicle driveability during a cam or crank sensor MIL condition(2017 MY Only). Improved knock sensor performance.
Source components: BACK OVER PREVENTION · ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · EXTERIOR LIGHTING · FUEL SYSTEM, GASOLINE.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customer Satisfaction Notification T23 ? EGR Valve Function The Powertrain Control Module (PCM) on about 415,000 of the above vehicles has software that may be operating the Exhaust Gas Recirculation valve (EGR) with an aggressive seating velocity. An aggressive seating velocity may damage the EGR valve. As a result this condition may illuminate the Malfunction Indicator Lamp (MIL) and display a P0404 code. The PCM must be reprogrammed on all involved vehicles.
Source components: ELECTRICAL SYSTEM · EXTERIOR LIGHTING · FUEL SYSTEM, GASOLINE · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Radiator Before replacing the radiator call Wes Youkhana at FCA Auburn Hills cell: (248) 564-8595 to answer a few questions. If no response in 15 minutes, please proceed with repair. When replacing Radiator for damage on engine side of radiator, also replace fan module and ship the old fan using the same ticket number.
Source components: ENGINE AND ENGINE COOLING:COOLING SYSTEM:RADIATOR ASSEMBLY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Liftgate Latch Before replacing this part, please call Lori Millen at cell (248) 379-1888. If you do not receive a return call within 15 minutes, proceed with the repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin provides information regarding the latest Flash Over The Air update (FOTA) and provides a service technician an overview of the steps a customer will need to take to complete the update.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. In addition Some customers may experience one or more of the following condition:Customer complains of shift quality bumps (Sales Code EZH only). During an engine limp mode condition, the transmission remains in a fixed gear. The following software enhancements are also available:Start Stop quality enhancement (WK with Sales Code ERC only). Transmission shift quality enhancement.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. Some customers may experience one or more of the following condition:Customer complains of shift quality bumps(Sales Code EZH only). During an engine limp mode condition, the transmission remains in a fixed gear. The following software enhancement is also available:Transmission shift quality enhancement.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
RA2 Radio 5" Uconnect Before replacing this radio, make sure you can reproduce the customer issue. If the radio is locked up, has a blank screen, or no sound, please perform a vehicle battery reset. If radio functionality is resumed, return the vehicle to the customer. If there are any questions or concerns or the vehicle has been in for repair for the same radio concern more than once, please call Rick Gordon at Cell (248) 630- 6281. If no response in 15 minutes, proceed with repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Radiator Before replacing the radiator call Wes Youkhana at FCA Auburn Hills cell: (248) 564-8595 to answer a few questions. If no response in 15 minutes, please proceed with repair.
Source components: ENGINE AND ENGINE COOLING:COOLING SYSTEM:RADIATOR ASSEMBLY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Pentastar Oil Filter Adapter All vehicles equipped with a 3.2L or 3.6L engine; If replacing the Oil Filter Adapter (OFA) due to a leak detected between OFA and block, an O-ring kit (68191356AA) is now available to repair OFA/Block Interface leaks. Using dye will assist in determining source of leak. Ensure OFA Cap Oring is seated in the proper groove in the cap and not damaged or cut. Engineering is seeking information regarding OFA leaks. Questions/info can be directed to: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Ron Dallison Cell (248-292-9510) ron.dallison@fcagroup.com Joe Lovell Cell (734) 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Fuel Tank Before replacing this part due to Hard to Fill condition, check the Fuel Filler Tube for restriction after the second door of the capless unit. Replace the Fuel Filler Tube if the second door of the capless unit does not open properly. Contact Sylvia Lopez at (248) 520-9734 if a Tank needs to be replaced.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Radiator Before replacing the radiator call Wes Youkhana at FCA Auburn Hills cell: (248) 564-8595 to answer a few questions. If no response in 15 minutes, please proceed with repair.
Source components: ENGINE AND ENGINE COOLING:COOLING SYSTEM:RADIATOR ASSEMBLY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Pentastar Oil Filter Adapter All vehicles equipped with a 3.2L or 3.6L engine; If replacing the Oil Filter Adapter (OFA) due to a leak detected between OFA and block, an O-ring kit (68191356AA) is now available to repair OFA/Block Interface leaks. Using dye will assist in determining source of leak. Ensure OFA Cap Oring is seated in the proper groove in the cap and not damaged or cut. Engineering is seeking information regarding OFA leaks. Questions/info can be directed to: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Ron Dallison Cell (248-292-9510) ron.dallison@fcagroup.com Joe Lovell Cell (734) 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Fuel Tank Before replacing this part due to Hard to Fill condition, check the Fuel Filler Tube for restriction after the second door of the capless unit. Replace the Fuel Filler Tube if the second door of the capless unit does not open properly. Contact Sylvia Lopez at (248) 520-9734 if a Tank needs to be replaced.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Accelerator Pedal Before replacing accelerator pedal, be sure to follow fault code diagnostic procedures in service manual. Make sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Accelerator Pedal Before replacing accelerator pedal, be sure to follow fault code diagnostic procedures in service manual. Make sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Rear View Camera In the case for inoperative camera, radio screen is blue or black in reverse mode. Before proceeding with the normal procedure call Ali Ikram at (248) 576-9265 Mon- Fri between 8 am- 4pm. If you do not get a response within 15 minutes continue with the repair. Make sure that connector is inserted properly. If there is a need to replace camera. In case of bad wire harness. Replace the harness and have it sent back to QEC.
Source components: BACK OVER PREVENTION: SENSING SYSTEM: CAMERA.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Brake Pedal Sensor For vehicles with DTC's P0572 or C0042, or complaints of brake lights staying on or cruise control not setting, please use wiTech to check the Brake Pedal Home Position setting and actual pedal resting position under brake pedal status in the ABS module. Before replacing the Brake Pedal Position Sensor, please call Rick Gordon at Cell (248) 630-6281. If no response within 15 minutes, proceed with repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Blind Spot Detection Sensor If you are replacing this part due to a customer complaint of "Blind spot alert unavailable - wipe rear bumper", please read the following instructions before proceeding. 1) Verify that the rear bumper is clear of any obstructions. The process to clear the blockage message involves first cycling the ignition. 2) The vehicle must be driven on the road and pass/be passed by vehicles on both the left and right sides. After completing those steps, the blockage message will clear and the system will function as designed. Please call Zaid Almasarweh (586) 258-6771 if the previous steps do not correct the problem. If there is no response within 15 minutes, please continue with your normal diagnostic process.
Source components: BACK OVER PREVENTION · ELECTRICAL SYSTEM:ADAS:BLINDSPOT:SENSORS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Rear View Camera In the case for inoperative camera, radio screen is blue or black in reverse mode. Before proceeding with the normal procedure call Ali Ikram at (248) 576-9265 Mon- Fri between 8 am- 4pm. If you do not get a response within 15 minutes continue with the repair. Make sure that connector is inserted properly. If there is a need to replace camera. In case of bad wire harness. Replace the harness and have it sent back to QEC.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Brake Pedal Sensor For vehicles with DTC's P0572 or C0042, or complaints of brake lights staying on or cruise control not setting, please use wiTech to check the Brake Pedal Home Position setting and actual pedal resting position under brake pedal status in the ABS module. Before replacing the Brake Pedal Position Sensor, please call Rick Gordon at Cell (248) 630-6281. If no response within 15 minutes, proceed with repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Blind Spot Detection Sensor If you are replacing this part due to a customer complaint of "Blind spot alert unavailable - wipe rear bumper", please read the following instructions before proceeding. 1) Verify that the rear bumper is clear of any obstructions. The process to clear the blockage message involves first cycling the ignition. 2) The vehicle must be driven on the road and pass/be passed by vehicles on both the left and right sides. After completing those steps, the blockage message will clear and the system will function as designed. Please call Zaid Almasarweh (586) 258-6771 if the previous steps do not correct the problem. If there is no response within 15 minutes, please continue with your normal diagnostic process.
Source components: LANE DEPARTURE: BLIND SPOT DETECTION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Transmission Diagnostic And Shift Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. Some customers may experience the following condition: During an engine limp mode condition, the transmission remains in a fixed gear.The following software enhancement is also available: Transmission shift quality enhancement.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following DTCs set in the PCM memory: U1424 - Implausible Engine Torque Signal Received (2017 MY Only). P2681 - Engine Coolant Bypass Valve Control Circuit Open (3.6L Only). P0335 - Crankshaft Position Sensor Circuit. P2299-00 - Brake Pedal Position/Accelerator Pedal Position Incompatible. B23C3 - Stop/Start Disable Switch 1/2 Correlation (3.0L and 3.6L Only).In addition, customers may experience the following conditions: A shorter auxiliary battery life. An illuminated Automatic Oil Change Indication (AOCI) light (3.6L Only).Other enhancements included in this update: Improved knock sensor performance.
Source components: AIR BAGS · BACK OVER PREVENTION · ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · EXTERIOR LIGHTING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Transmission Diagnostic And Shift Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. Some customers may experience the following condition: During an engine limp mode condition, the transmission remains in a fixed gear.The following software enhancement is also available: Transmission shift quality enhancement.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following DTCs set in the PCM memory: U1424 - Implausible Engine Torque Signal Received (2017 MY Only). P2681 - Engine Coolant Bypass Valve Control Circuit Open (3.6L Only). P0335 - Crankshaft Position Sensor Circuit. P2299-00 - Brake Pedal Position/Accelerator Pedal Position Incompatible. B23C3 - Stop/Start Disable Switch 1/2 Correlation (3.0L and 3.6L Only).In addition, customers may experience the following conditions: A shorter auxiliary battery life. An illuminated Automatic Oil Change Indication (AOCI) light (3.6L Only).Other enhancements included in this update: Improved knock sensor performance.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Trans Pan or Gasket If your repair requires replacing one of the two part numbers for a leak, prior to the repair please call Enzo Piazza at cell (248) 467-9163. If you cannot reach Enzo within 15 minutes proceed with the repair. Enzo needs to know the location of the leak, if the bolts were torqued, if there is sealer skip, or anything that may be pertinent to the cause of the leak. Photos would be very helpful and can be sent to Enzo's cell phone or his email. Enzo's e-mail address is enzo.piazza@fcagroup.com.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Electric Power Steering Gear If any of the following DTCs exist, it is okay to replace the steering gear: C2217-00, C15C1-00 (EPS Mechanical Performance) or C15DB-00 (Latch Active) otherwise perform the following; 1) Electrical, Communication or DTC (other then above) issue please contact: Terry Gavit @ cell (248) 882-6108 terry.gavit@fcagroup.com Engineering is requesting a copy of Vehicle Scan Report (VSR) to be emailed to the above address. 2) Noise or Mechanical issue please contact: Ruth Delong @ cell (810) 569-0354.~ If you do not receive a return call within 15 minutes, proceed with the repair.~ Please be sure to attach a copy of the Vehicle Scan Report on the repair order
Source components: BACK OVER PREVENTION · POWER TRAIN · STEERING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Door Hinge Assembly Side door hinge noisy. Only replace the door hinge with the integral check device. Do not replace the simple hinge if it is not damaged it is not the source of the noise. Replacing it unnecessary and is an over-repair.
Source components: STRUCTURE:BODY:DOOR:HINGE AND ATTACHMENTS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Trans Pan or Gasket If your repair requires replacing one of the two part numbers for a leak, prior to the repair please call Enzo Piazza at cell (248) 467-9163. If you cannot reach Enzo within 15 minutes proceed with the repair. Enzo needs to know the location of the leak, if the bolts were torqued, if there is sealer skip, or anything that may be pertinent to the cause of the leak. Photos would be very helpful and can be sent to Enzo's cell phone or his email. Enzo's e-mail address is enzo.piazza@fcagroup.com.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Electric Power Steering Gear If any of the following DTCs exist, it is okay to replace the steering gear: C2217-00, C15C1-00 (EPS Mechanical Performance) or C15DB-00 (Latch Active) otherwise perform the following; 1) Electrical, Communication or DTC (other then above) issue please contact: Terry Gavit @ cell (248) 882-6108 terry.gavit@fcagroup.com Engineering is requesting a copy of Vehicle Scan Report (VSR) to be emailed to the above address. 2) Noise or Mechanical issue please contact: Ruth Delong @ cell (810) 569-0354.~ If you do not receive a return call within 15 minutes, proceed with the repair.~ Please be sure to attach a copy of the Vehicle Scan Report on the repair order
NHTSA source summary · Original PDF not reviewed by Recallfolio
Door Hinge Assembly Side door hinge noisy. Only replace the door hinge with the integral check device. Do not replace the simple hinge if it is not damaged it is not the source of the noise. Replacing it unnecessary and is an over-repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Poor Vehicle Acceleration This bulletin involves test driving the vehicle and if required, replacing the fuel pump module. The customer may notice the vehicle has poor acceleration and/or the transmission will not upshift under Wide Open Throttle (WOT). This can be caused by low fuel flow from the fuel pump module.
Source components: FUEL SYSTEM, GASOLINE · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Oil Pump Assembly If error code P06DD present on any Pentastar V6 application, please inspect oil pump for relief valve failure. See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system
NHTSA source summary · Original PDF not reviewed by Recallfolio
Poor Vehicle Acceleration This bulletin involves test driving the vehicle and if required, replacing the fuel pump module. The customer may notice the vehicle has poor acceleration and/or the transmission will not upshift under Wide Open Throttle (WOT). This can be caused by low fuel flow from the fuel pump module.
Source components: FUEL SYSTEM, GASOLINE · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Oil Pump Assembly If error code P06DD present on any Pentastar V6 application, please inspect oil pump for relief valve failure. See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system
NHTSA source summary · Original PDF not reviewed by Recallfolio
Auto Trans Rotary Electronic Shifter The rotary shifter is designed to actuate a motor within the device whenever the driver places their foot on the brake, with the car in Park (or Neutral). This generates a noise with each brake press/release. Therefore, even after replacing the shifter for a noise complaint, the replacement part will also have a characteristic noise generated whenever the driver steps on the brake. Before performing a repair procedure for a noise complaint, please perform a subjective analysis of the noise coming from the rotary shifter. If the shifter noise is deemed abnormal sound (has an uncharacteristic buzz or grind), please proceed with normal replacement procedure. If so equipped, record the sound with a handheld microphone, or cell phone, and if noise is above 54dB @ 30cm away from the knob, please proceed with normal replacement procedure. For any further questions, please contact Theodore Kahiya at cell (519) 300-2443.
Source components: ENGINE AND ENGINE COOLING · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Cleaner For A/C Evaporator Before using deodorizer to remove HVAC or evaporator odor, call Ken Deneau at cell (248) 765-0288. If no response in 15 minutes, please continue with repair
NHTSA source summary · Original PDF not reviewed by Recallfolio
Auto Trans Rotary Electronic Shifter The rotary shifter is designed to actuate a motor within the device whenever the driver places their foot on the brake, with the car in Park (or Neutral). This generates a noise with each brake press/release. Therefore, even after replacing the shifter for a noise complaint, the replacementpart will also have a characteristic noise generated whenever the driver steps on the brake. Before performing a repair procedure for a noise complaint, please perform a subjective analysis of the noise coming from the rotary shifter. If the shifter noise is deemed abnormal sound (has an uncharacteristic buzz or grind), please proceed with normal replacement procedure. If so equipped, record the sound with a handheld microphone, or cell phone, and if noise is above 54dB @ 30cm away from the knob, please proceed with normal replacement procedure. For any further questions, please contact Theodore Kahiya at cell (519) 300-2443.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Cleaner For A/C Evaporator Before using deodorizer to remove HVAC or evaporator odor, call Ken Deneau at cell (248) 765-0288. If no response in 15 minutes, please continue with repair
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Transmission Diagnostic And Shift Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. Some customers may experience the following condition: · During an engine limp mode condition, the transmission remains in a fixed gear. The following software enhancement is also available: · Transmission shift quality enhancement.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following DTCs set in the PCM memory: U1424 - Implausible Engine Torque Signal Received (2017 MY 3.0L and 3.6L Only). P2681 - Engine Coolant Bypass Valve Control Circuit Open (3.6L Only). P0335 - Crankshaft Position Sensor Circuit. P2299-00 - Brake Pedal Position/Accelerator Pedal Position Incompatible. B23C3 - Stop/Start Disable Switch 1/2 Correlation (3.0L and 3.6L Only). In addition, customers may experience the following conditions: A shorter auxiliary battery life. An illuminated Automatic Oil Change Indication (AOCI) light (3.6L Only). Other enhancements included in this update: Improved knock sensor performance.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Transmission Diagnostic And Shift Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. Some customers may experience the following condition: · During an engine limp mode condition, the transmission remains in a fixed gear. The following software enhancement is also available: · Transmission shift quality enhancement.
Source components: ELECTRICAL SYSTEM · POWER TRAIN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following DTCs set in the PCM memory: U1424 - Implausible Engine Torque Signal Received (2017 MY 3.0L and 3.6L Only). P2681 - Engine Coolant Bypass Valve Control Circuit Open (3.6L Only). P0335 - Crankshaft Position Sensor Circuit. P2299-00 - Brake Pedal Position/Accelerator Pedal Position Incompatible. B23C3 - Stop/Start Disable Switch 1/2 Correlation (3.0L and 3.6L Only). In addition, customers may experience the following conditions: A shorter auxiliary battery life. An illuminated Automatic Oil Change Indication (AOCI) light (3.6L Only). Other enhancements included in this update: Improved knock sensor performance.
Source components: ELECTRICAL SYSTEM · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following DTCs set in the PCM memory: P2681 - Engine Coolant Bypass Valve Control Circuit Open (3.6L Only). P0335 - Crankshaft Position Sensor Circuit. P2299-00 - Brake Pedal Position/Accelerator Pedal Position Incompatible. B23C3 - Stop/Start Disable Switch 1/2 Correlation (3.0L and 3.6L Only).In addition, customers may experience the following conditions: A shorter auxiliary battery life. An illuminated Automatic Oil Change Indication (AOCI) light (3.6L Only).Other enhancements included in this update: Improved knock sensor performance.
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM).
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: Blind Spot Monitor System Improvements This bulletin involves updating the Left and Right Blind Spot Sensor (LBSS/RBSS) software. The customer may experience the blind spot monitor indicator may not chime alerting them that there is an object next to the vehicle.
Source components: LANE DEPARTURE: BLIND SPOT DETECTION.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Incorrect Gap Tolerance Between The Liftgate And Left Tail Lamp This bulletin involves removing excess sealant from the body behind the tail lamp to open the gap clearance between the left tail lamp and the liftgate. .1 - Gap Clearance Too Close (Left Side)1 - Proper Gap Clearance (Right Side)
NHTSA source summary · Original PDF not reviewed by Recallfolio
Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform the this inspection. Inspect the sensor for a fluid coating on the sensor pins. Orange colored rain repellant can cause this fluid build-up. Clean the pins, drain the reservoir, and fill with Mopar approved washer fluid. Check to determine if the issue has been resolved. Continue with repair if necessary. Also, please inform the customer not to use Rain-X in the system to avoid this issue. Please contact Chuck Hood at cell (248) 613-7591 if you have questions or need additional information. Thank you.
NHTSA source summary · Original PDF not reviewed by Recallfolio
PSU Exhaust Phaser 05048043AB If replacing the Exhaust Phaser for the following codes: P0340 Cam Missing/Camshaft Sensor Circuit and/or P0345 Cam Missing/Camshaft Sensor Circuit Engineering is requesting that all three Valve Timing components (Phaser, Actuator, OCV) be replaced.~ Please label the components of which bank they came from prior to parts return. ~ Phaser 05048043AB Actuator 05048045AB OCV 05048044AB Please call Joe Lovell at cell (734) 309-6467 with any questions If a response is not received within 15 mins , then proceed with diagnostics/repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Intake Manifold Gasket Intake Manifold Gaskets on Pentastar Upgrade (Sales Code ERC/ERF) are reusable provided they are not cut, torn or melted. The gaskets are not required by warranty to be replaced like they are on Pentastar Classic (ERB/EHB). The new gaskets are not interchangeable with Pentastar Classic Intake Manifold Gaskets.
NHTSA source summary · Original PDF not reviewed by Recallfolio
82212076, 82203694 - Fabric Cleaner This "fabric cleaner" is not intended for sale in California, the otc states (Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~