Original record summaries, dates and identifiers for this model-year. Records 1–100 of 218, ordered newest first. Dated records on this page: May 4, 2016–May 29, 2026.
Read the applicability before drawing a conclusion.
This archive includes service bulletins, warranty notices, software instructions and other communications. Records may repeat or supersede earlier instructions. A model-year association is not proof that a document covers every engine, trim, VIN or reported symptom, or that a repair is free.
NHTSA download snapshot: Sep 28, 2026. These are communication associations for this vehicle, not unique defects. How records are joined and counted.
May 29, 2026Service Bulletin/Repair Instructions
S1623000028 REV.I
NHTSA communication ID: 11033308
NHTSA source summary · Original PDF not reviewed by Recallfolio
Outside Power Fold Rearview Mirror Noise Or Loose At Pivot. Mirror Contacts Door Window Glass In The Folded Position.
Source components: ELECTRICAL SYSTEM · STRUCTURE:BODY.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Verify Reman part number availability. Order the "R" part number for all orders: Warranty, Mopar, customer pay and service contract. Order "68" part number for New unsold units only.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates
NHTSA source summary · Original PDF not reviewed by Recallfolio
FUEL PUMP/LEVEL UNIT MODULE For vehicles with Saddle Fuel Tanks, need to determine if there are any DTCs in wiTECH. Follow Service Diagnostics published prior to making any changes. Review any existing SOL or TSBs published for customer complaint issue. Only the Fuel Pump Module should be replaced if there are DTCs associated with the Fuel Level Sensor number 1. Only the Auxiliary Level Sender should be replaced if there are DTCs associated with the Fuel Level Sensor number 2. If there is a mixture of DTCs between the Fuel Pump Module and the Auxiliary Level Sensor, then investigate if there is a Jumper Harness or circuit issue between the Level Sender and the PCM. Verify fuel transfer between auxiliary tank and the primary tank by monitoring the auxiliary level sensor to verify it drops after driving.
NHTSA source summary · Original PDF not reviewed by Recallfolio
"Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Verify current warranty policy to determine if digital imaging pre-authorization is required or pre-approval is required from the Regional Office; depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels."
NHTSA source summary · Original PDF not reviewed by Recallfolio
COOLER Engine Oil Please be aware that the oil cooler seal is serviceable as a standalone part and should be considered for replacement as a remedy for fluid leak.
NHTSA source summary · Original PDF not reviewed by Recallfolio
LIFTER, Hydraulic Roller Deactivating Please do not replace MDS lifters because the disconnecting pin is not lined up, this is normal and not a defect.
NHTSA source summary · Original PDF not reviewed by Recallfolio
LIFTER, Hydraulic Roller Deactivating Please do not replace MDS lifters because the disconnecting pin is not lined up, this is normal and not a defect.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Connector kit Before ordering this connector repair kit 68018957A$, check it in the Mopar Connector Repair Kit Website to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Lubrication and Maintenance Fluids If MOPAR fluids and chemicals are not readily available, please review Service Library for specifications so a suitable alternative can be used
NHTSA source summary · Original PDF not reviewed by Recallfolio
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
NHTSA source summary · Original PDF not reviewed by Recallfolio
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
NHTSA source summary · Original PDF not reviewed by Recallfolio
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
NHTSA source summary · Original PDF not reviewed by Recallfolio
ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Aluminum Body Panel Corrosion Repair Aluminum corrosion or bubbling along the leading edge of hood, hinges or other exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Digital imaging pre authorization is required for Smart Warranty Base dealers or Pre Approval is required from Regional Office depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
Source components: STRUCTURE · STRUCTURE:INTERIOR PANELS:DOOR · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Oil Filter If a Mopar Oil Filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils. Recommended Brands: Wix, Purolator, and NapaGold
Source components: POWER TRAIN:AUTOMATIC TRANSMISSION:FLUID/LUBRICANT:FILTER/SCREEN.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customer complaints may include abnormal engine noise, rough idle, lack of power, misfire. Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.
Source components: ENGINE AND ENGINE COOLING:ENGINE:CRANK/CAMSHAFT POSITION SENSOR · UNKNOWN OR OTHER.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customer complaints may include abnormal engine noise, rough idle, lack of power, misfire. Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.
Source components: ENGINE · ENGINE AND ENGINE COOLING.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
NHTSA source summary · Original PDF not reviewed by Recallfolio
ADAPTER, Engine Oil Filter (Pentastar V6) All vehicles equipped with a 3.2L or 3.6L except for model year 2014 vehicles with leak concern: 1) Ensure the Oil Filter Adapter (OFA) Cap O-ring is seated in the proper groove in the cap and not damaged or cut. 2) If replacing the (OFA) due to a leak detected between (OFA) and block. Ensure the torque on the 5 bolts are torqued to 12nm. If not record the actual values, torque to 12nm and contact the FCA employees listed below. 3) Remove the (OFA) and replace the O-ring and gaskets only (Kit #68191356A$), NOT THE OFA. 4) If oil was drained, add oil dye to ensure the leak is repaired. For model year 2014 vehicles replace the Oil Filter Adaptor. 5) When replacing PN's 68310865A$ & 68308741A$, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
NHTSA source summary · Original PDF not reviewed by Recallfolio
PLATE - CLUTCH PRESSURE For 68RFE trans use selective fit pressure plates between the overdrive and reverse clutch packs and hence use all three 52119929A$, 52119930A$, 04799116A$ maintain clearance For 65RFE & 66RFE no selectives for this pressure plate: 65RFE use 04799116A$ 66RFE use 52119929A$
NHTSA source summary · Original PDF not reviewed by Recallfolio
PLATE - CLUTCH PRESSURE For 68RFE trans use selective fit pressure plates between the overdrive and reverse clutch packs and hence use all three 52119929A$, 52119930A$, 04799116A$ maintain clearance For 65RFE & 66RFE no selectives for this pressure plate: 65RFE use 04799116A$ 66RFE use 52119929A$
Source components: EQUIPMENT · EQUIPMENT ADAPTIVE/MOBILITY · SERVICE BRAKES.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customer complaints may include abnormal engine noise, rough idle, lack of power, misfire. Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.
Source components: ENGINE AND ENGINE COOLING:ENGINE:CRANK/CAMSHAFT POSITION SENSOR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Customer complaints may include abnormal engine noise, rough idle, lack of power, misfire. Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Active Head Restraint (AHR) Inadvertent Deployment - X88 Warranty Extension This bulletin involves inspecting the sled bracket striker pin and possibly replacinga front seat AHR that has inadvertently deployed. Customers may comment on the following: The AHR is deployed on one or both front seats and will not reset.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Active Head Restraint (AHR) Inadvertent Deployment - X88 Warranty Extension This bulletin involves inspecting the sled bracket striker pin and possibly replacing a front seat AHR that has inadvertently deployed. Customers may comment on the following:The AHR is deployed on one or both front seats and will not reset.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Active Head Restraint (AHR) Inadvertent Deployment - X88 Warranty Extension This bulletin involves inspecting the sled bracket striker pin and possibly replacing a front seat AHR that has inadvertently deployed. Customers may comment on the following:The AHR is deployed on one or both front seats and will not reset.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Active Head Restraint (AHR) Inadvertent Deployment - X88 Warranty Extension This bulletin involves inspecting the sled bracket striker pin and possibly replacing a front seat AHR that has inadvertently deployed. Customers may comment on the following:The AHR is deployed on one or both front seats and will not reset.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Aluminum Body Panel Corrosion Repair This bulletin involves inspecting and if necessary removing corrosion and refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Aluminum Body Panel Corrosion Repair This bulletin involves inspecting and if necessary removing corrosion and refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Charging System, Battery Diagnostic Tools and Warranty This information only bulletin discusses using the correct test equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Air Suspension Components Star Parts Catalog has been updated to show individual service parts for the compressor assembly. This will allow service technicians to repair the root cause without over repairing the system. Replace only the part deemed failed by the diagnostics performed. Individual parts include: - Compressor - Valve block - Individual hoses - Temp sensor - Shield - Air line clips NOTE: in most situations when a new compressor is needed, the compressor as a separate part is the correct repair, and the assembly would not be required.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Authentic Mopar® Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar® Glass.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Authentic Mopar® Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar® Glass.
NHTSA source summary · Original PDF not reviewed by Recallfolio
RADIO [RES] - New and/or Service Exchange For RES radio concerns. Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Oil Filter Adapter If replacing Oil Filter Adapter due to oil leak, please be aware a seal kit is available for repair. If replacing due to missing Spring Loaded Check Valve, a replacement spring and check valve are now available through MOPAR.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Oil Pump Assembly If error code P06DD present on any Pentastar V6 application, please inspect oil pump for relief valve failure. See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system
NHTSA source summary · Original PDF not reviewed by Recallfolio
Oil Pump Assembly If error code P06DD present on any Pentastar V6 application, please inspect oil pump for relief valve failure. See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system
NHTSA source summary · Original PDF not reviewed by Recallfolio
Steering Column If vehicle comes in for steering column replacement, verify column installed. Go to Info Column in Star Parts and open the flow chart to determine which column is installed. If column is Daimler, verify that a replacement Daimler column is in stock and use for replacement. If no Daimler column is in stock, replacement must use Presta column (which require a number of other components to be replaced). For more information and details on PN's, see W-Series Flowchart in Star Parts. Contact parts specifying for assistance regarding correct part numbers, for technical assistance contact Star. UPDATE: 11/9/2016 If the new bearing does not fit through the double dash, you need to replace the lower double dash panel to the latest level. Please see the updated flowchart in StarParts for the correct replacement panel.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Flash: HVAC System Enhancement This bulletin involves reprogramming the Heating Ventilation Air Conditioning (HVAC) Module with new software. Customers may describe an unpleasant odor in the vehicle after driving from highway speed limits back down to city speed limits.Updating the HVAC software will correct these conditions.
Source components: ELECTRICAL SYSTEM · VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform the this inspection. Inspect the sensor for a fluid coating on the sensor pins. Orange colored rain repellant can cause this fluid build-up. Clean the pins, drain the reservoir, and fill with Mopar approved washer fluid. Check to determine if the issue has been resolved. Continue with repair if necessary. Also, please inform the customer not to use Rain-X in the system to avoid this issue. Please contact Chuck Hood at cell (248) 613-7591 if you have questions or need additional information. Thank you.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Steering Column If vehicle comes in for steering column replacement, verify column installed. Go to Info Column in Star Parts and open the flow chart to determine which column is installed. If column is Daimler, verify that a replacement Daimler column is in stock and use for replacement. If no Daimler column is in stock, replacement must use Presta column (which require a number of other components to be replaced). For more information and details on PN's, see W-Series Flowchart in Star Parts. Contact parts specifying for assistance regarding correct part numbers, for technical assistance contact Star.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Seat Shields For vehicles built prior to 5/2/2011:~ Replace old shield (1UN79TRMAA) with new shield (1XN97TRMAA) and bracket (68100737AA).~ Replace old shield (1UP58TRMAA) with new shield (1XN08TRMAA) and bracket (68100737AA).~ Replace old shield (1UQ14TRMAA) with new shield (1XN96TRMAA) and bracket (68100737AA).~ The new bracket (68100737AA) is only needed if the vehicle doesn't already have it (check PN on phyical part)
Source components: STRUCTURE:FRAME AND MEMBERS:UNDERBODY SHIELDS.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Steering Column If vehicle comes in for steering column replacement, verify column installed. Go to Info Column in Star Parts and open the flow chart to determine which column is installed. If column is Daimler, verify that a replacement Daimler column is in stock and use for replacement. If no Daimler column is in stock, replacement must use Presta column (which require a number of other components to be replaced). For more information and details on PN's, see W-Series Flowchart in Star Parts. Contact parts specifying for assistance regarding correct part numbers, for technical assistance contact Star.
NHTSA source summary · Original PDF not reviewed by Recallfolio
Seat Shields For vehicles built prior to 5/2/2011:~ Replace old shield (1UN79TRMAA) with new shield (1XN97TRMAA) and bracket (68100737AA).~ Replace old shield (1UP58TRMAA) with new shield (1XN08TRMAA) and bracket (68100737AA).~ Replace old shield (1UQ14TRMAA) with new shield (1XN96TRMAA) and bracket (68100737AA).~ The new bracket (68100737AA) is only needed if the vehicle doesn't already have it (check PN on phyical part)
NHTSA source summary · Original PDF not reviewed by Recallfolio
PSU Exhaust Phaser 05048043AB If replacing the Exhaust Phaser for the following codes: P0340 Cam Missing/Camshaft Sensor Circuit and/or P0345 Cam Missing/Camshaft Sensor Circuit Engineering is requesting that all three Valve Timing components (Phaser, Actuator, OCV) be replaced.~ Please label the components of which bank they came from prior to parts return. ~ Phaser 05048043AB Actuator 05048045AB OCV 05048044AB Please call Joe Lovell at cell (734) 309-6467 with any questions If a response is not received within 15 mins , then proceed with diagnostics/repair.
NHTSA source summary · Original PDF not reviewed by Recallfolio
RES / RHA / REB radio that supports Bluetooth and Hands-Free For issues with Bluetooth, Hands-Free Calling, and/or Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)
Source components: ELECTRICAL SYSTEM · EQUIPMENT · EQUIPMENT:ELECTRICAL.